VANITY INSTALLATION INSTRUCTIONS

Transcription

1 VANITY INSTALLATION INSTRUCTIONS Congratulations and thank you for your purchase. These cabinets have been designed and assembled to a very high standard and if installed correctly will provide you with many years of reliability. Some or all of the following instructions will be required for installing your new vanity, please read all of these instructions carefully before starting the installation. This will ensure the best possible result and avoid missing or overlooking any appropriate installation procedure which could invalidate your warranty. CONTENT Installation Instructions for all vanity cabinets Page 2 Additional Instructions when using Wall Hung cabinets Page 3 Special Installation Instructions for Poly Marble Tops Page 4 Special Installation Instructions for Vitreous China Tops Page 5 Cleaning and Maintenance Page 6 Page 1

2 Installation Instructions for all vanity cabinets INSPECTION AFTER OPENING Before installation, remove all packaging and check that the unit is in good working order and that no damage has occurred in transit. If damage has occurred, or a defect is noticed DO NOT continue with installation, contact your supplier ASAP. INSTALLATION TOOLS REQUIRED Power Drill Drill Bits Tape Measure Pencil Spirit Level Hole Saws Screws Screw Driver Silicone Caulking Gun STEP 1, To help in the installation, label and remove the doors fronts and drawers (If removable), store them in a safe place where they will not get damaged. STEP 2, Check that the unit will fit into the location allowing for the top to overhang the unit 10mm on each side. On timber walls, mark the positions of the studs so to be able to fix the unit to these later. Measure and mark the hole centre of the water supply and waste outlet on the back and/or bottom of the unit. Check that the pipes will not interfere with the drawers. STEP 3, Use a slightly larger hole saw, drill the holes for the water supply and waste outlet. Position the unit into its correct place and check unit fits correctly. Re-drill if required. STEP 4, Re-attach door panels and drawers. Check that the unit is sitting level, and is not twisted and that the drawers and doors are not racked or out of alignment. Wedges can be used if required. (NOTE: Door hinges can be adjusted to help in the realignment) STEP 5, Drill holes and fix the back of the unit to the wall. Align holes with stud if fixing to a timber wall. If no studs are accessible a toggle type system is required (fixings not supplied). STEP 6, Once unit is fixed to the wall, re-check that the doors and drawers are aligned and working correctly. Adjust screws and wedges if required. Use silicone to seal around the unit between the cabinet and the floor, and the cabinet sides and the wall (not the top). Page 2

3 Additional Instructions when using Wall Hung cabinets These additional instructions are numbered to work in conjunction with the Installation Instructions for all vanity cabinets. Please combine these 2 pages to ensure the appropriate installation steps are followed. STEP 1b, The recommended installation height to the top of the basin (front edge) is between mm off the finished floor. Extra timber supports are required in the wall if fixing this unit to a timber wall. (NOTE: A solid horizontal support in the wall just below the top of the unit is recommended) STEP 2b Position the unit against the wall (or an alternate wall) with additional support packers and check that the unit is sitting at the correct height and that it is level and is correctly positioned against the wall. Adjust if required and re-check pipe markings. (NOTE: Re-adjustment of the pipes maybe required if these are now exposed under base) STEP 5b, Position the fixing so the back panel is well supported. It is highly recommended 3-4x 75mm Coach Screws are used on a timber wall, and 3-4x 75mm Masonry Anchor on a solid wall. (NOTE: To help support and spread the load, washers should be used with each fixing) STEP 6b, Remove additional support packers and re-check that the doors and drawers are aligned, adjust if required. Use silicone to seal the sides of the cabinet and the wall (not the top). Page 3

4 Special Installation Instructions for Poly Marble Tops INSPECTION AFTER OPENING Before installation, remove all packaging and check that the top is the correct model and that no damage has occurred in transit. If damage has occurred, or a defect is noticed DO NOT continue with installation, contact your supplier ASAP. STEP 1, Check that your selected tapware and waste fit correctly, place the top into its correct position on the cabinet and check that it overhangs the cabinet on both ends and the front. If not, DO NOT continue with the installation, and contact your supplier ASAP. Small adjustments can be made to the back of the top with a belt sander If the back does not fit completely flush against the wall. STEP 2, Remove top and attach the waste and tapware according to their manufacturer s directions. STEP 3, Apply a continuous bead of silicone around the top edge of the cabinet. STEP 4, Place top onto the cabinet ensuring that it is overhanging evenly on both sides and that the back rests flush against the wall. Wipe off all excess silicone. STEP 5, Connect the water supply and the waste outlet as per their manufacturer s directions, run both hot and cold water and check for leaks. Repair if necessity. STEP 6, Use silicone to seal between the top and the wall. To create a professional finish use masking tape on the wall and the top allowing a big enough gap between the two to apply the silicone. Run a gloved finger along the silicone to smooth it out and cover both edges of the masking tape. Peel the masking tape away before the silicone starts to set. (NOTE: Allow 48 hours for the silicone to dry before using) Page 4

5 Special Installation Instructions for Vitreous China Tops INSPECTION AFTER OPENING Before installation, remove all packaging and check that the top is the correct model and that no damage has occurred in transit. If damage has occurred DO NOT continue with installation, contact your supplier ASAP. (NOTE: In the process of manufacturing vitreous china tops, the product shrinks significantly, and can sometimes lead to the product being slightly uneven, this is standard characteristic s of a vitreous china top) STEP 1, Check that your selected tapware and waste fit correctly, place the top into its correct position on the cabinet and check that it overhangs the cabinet on both ends and the front. If not, DO NOT continue with the installation, and contact your supplier ASAP. (NOTE: Check that the top does not rock on the cabinet more than 4mm, if so cabinet adjustments maybe required) STEP 2, Remove top and attach the waste and tapware according to their manufacturer s directions. STEP 3, Apply a continuous bead of silicone around the top edge of the cabinet. STEP 4, Place top onto the cabinet ensuring that it is overhanging evenly on both sides and that the back rests flush against the wall. Wipe off all excess silicone. STEP 5, Connect the water supply and the waste outlet as per their manufacturer s directions, run both hot and cold water and check for leaks. Repair if necessity. STEP 6, Use silicone to seal between the top and the wall. To create a professional finish use masking tape on the wall and the top allowing a big enough gap between the two to apply the silicone. Run a gloved finger along the silicone to smooth it out and cover both edges of the masking tape. Peel the masking tape away before the silicone starts to set. (NOTE: Allow 48 hours for the silicone to dry before using) Page 5

6 Cleaning and Maintenance IMPORTANT NOTICE This cabinet is made from water resistant board only (not water proof), so it is important that care is taken to clean up all water spillage. For personal and product safety, ensure that the HOT water supply is regulated to a maximum of 55 C. Daily Care: To protect the finish of your vanity, use a non-abrasive soap or liquid detergent to clean. Using an abrasive cleaner will dull the finish of your vanity top and cabinet and continued use may cause permanent damage to their finish. Staining: Do not use strong chemicals such as bleach or ammonia to clean your vanity. The finish on your vanity is highly resistant to staining by most household agents, but repeated exposure to strong chemicals may cause discoloration. Scratches and Dents: Your vanity top, although hard, can be scratched with a hard or sharp object. Most small surface scratches can be easily removed by applying a fine automotive rubbing compound and buffing. Deeper scratches may require sanding lightly with a 600+ grit wet sandpaper, followed by rubbing compound and automotive wax to restore the finish. Page 6