miramondo Technical Informations 1/7 La Strada

Transcription

1 1/7 La Strada Technical Informations public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

2 La Strada 2/7 Dimensions public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

3 La Strada 3/7 Hole pattern for mounting 1) With backrest 2) Without backrest 3) Table 650/1300/ /1244/ D /1300/ /1244/ D /1300/ /1234/ D public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

4 La Strada 4/7 Mounting Without foundation with threaded rod With foundation with threaded rod Threaded rod with mounting adhesive Concrete, Asphalt... Do not set nut and bolt in concrete in order to allow later disassembly Threaded rod with mounting adhesive Concrete >300 Gravel, sand... >200 Without foundation with screw and dowel With foundation with ground anchor Screw with dowel Concrete, Asphalt... Do not set nut and bolt in concrete in order to allow later disassembly Ground anchor Concrete 400 Gravel, sand... The fasteners are not included in the scope of delivery! >200 public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

5 La Strada 5/7 Maintenance Maintenance and care of the metal parts Notes about cleaning the powder-coated surface: - Only use clear water, if necessary with a little neutral cleaning agent added (ph 7) and soft, non-abrasive rags, cloths or industrial cotton. Do not rub hard. - Remove greasy, oily or sooty substances with aromatic-free petroleum spirits or isopropyl alcohol (IPA). Residues of stickers, chewing gum or adhesive bands, etc. can also be removed this way. - Do not use any solvents that contain esters, ketone, alcohols, aromatics, glycol ether or halogenated hydrocarbons or similar substances. - Do not use anything abrasive that will scratch. - Do not use strong acids or alkali cleaning agents. - Do not use cleaning agents of indeterminate composition. - The cleaning agents may not be used at temperatures that exceed 25 C. Do not use steam cleaning devices. - The surface temperature during cleaning may also not exceed 25 C. - Immediately after each cleaning, rinse with clear, cold water. Notes about refurbishing scratched steel parts: These recommendations will help refurbish a damaged surface. We ask you, however, to consider that refurbishment to the original surface quality is unfortunately not possible. A tolerance of the painted surfaces to cleaning agents, etc. which may be used to clean the surfaces must also be checked in each individual case and considered. The quality of the repairs made depends largely on the skill of the person making them. Unfortunately it is not possible to guarantee a particular result. The metal parts are made of hot-galvanised steel. They have a high-quality coating with a slight metallic pattern. Their colour is anthracite, similar to DB 703 metallic or RAL A single-component nitrocellulose paint with matte surface in the colour tone NCS 7500 N should be used to repair the powder coatings. The notes and warnings of the manufacturer in question apply for handling of the selected materials. Please do not forget to protect the surfaces against use and manipulation until the curing time recommended by the relevant manufacturer for the materials processed has elapsed. public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

6 La Strada 6/7 Maintenance Maintenance and care of the larch wood slats There are three surface treatments from which to choose. Untreated: Like all natural wood, untreated larch wood develops a beautiful silver-grey patina after weathering for a time. This protects the wood against UV rays naturally. Many of our customers like this optical transformation of the surface and they regard it as an authentic quality of the natural wood. Maintenance work for untreated wood is very easy, for it usually involves just sanding the surface. Transparent stained: For customers who would like a wood look but no greying of the surface, we offer the slats with a transparent stained finish. The stain is water-based and allows diffusion. It is applied in a medium coating thickness. The stain colour is reddish brown and darker than the natural colour of the larch wood, for it is the colour pigments that protect the wood against greying. In order to maintain a beautiful look, we recommend applying a maintenance coat of stain once a year. For this purpose, on request we can make available a pigmented natural oil glaze in a suitable colour tone. Opaque painted: Select from a collection of sixteen colours. The high-gloss paint is water-based like the transparent stain and it allows diffusion. It is also applied in a medium coating thickness and it is extremely UV-stable. Small and larger damage can be covered over easily with a maintenance coat of paint. This makes maintaining the slats extremely easy and helps keep the product looking good for a long time. For this purpose, on request we can make available a paint in a suitable colour tone. For the care of undamaged slats: Clean the slats, remove dust from them and if necessary degrease with soapy water or white spirits. Apply the natural oil or paint with a brush or cloth once. For damaged slats: Remove flaking glaze and loose parts. Sand weathered places down to the healthy wood. Clean the slats, remove dust from them and if necessary degrease with soapy water or white spirits. Then coat the whole slat once or twice with a brush. The notes and warnings of the manufacturer in question apply for handling of the selected materials. Please do not forget to protect the surfaces against use and manipulation until the curing time recommended by the relevant manufacturer for the materials processed has elapsed. public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -

7 La Strada 7/7 Tenders Text for invitation of tenders La Strada Preamble: All products listed and described below are protected by international design law. The transmission of these documents conveys no rights to existing design patents to the recipient or anyone else. Reproduction by a company other than public design GmbH is not allowed. Violations will be punished through legal means. The court of jurisdiction is Vienna, Austria. La Strada: Furniture product line for public outdoor spaces consisting of seating and table elements with surfaces of larch wood slats and steel frames in different versions: benches with backrest and armrest, benches with backrest and without armrest, benches without backrest, low tables and high tables in different dimensions. Wood surfaces untreated or glazed. All furniture is prepared for ground bolting or setting in concrete. Larch wood slats: Larch class 0-1 according to Austrian wood trade practices, without blue stain spots, centre-free and without centre cut-out, no open resin pockets, no end cracks, wood humidity approx. 12% to max. 14%. Slat diameter 80x34 mm in 3 lengths 640 mm, 1290 mm and 1940 mm. All edges are professionally planed and ground, all edges with 5mm chamfer. 2 lengthwise-running surfaces are slightly corrugated. The surfaces are available in two versions: untreated or glazed. Glaze: The slats are untreated or waterproofed and glazed twice with an open-pore medium coating glaze. The glaze is a steam-diffusion open water-based medium coating glaze. It is a glazing system equipped with UV absorbers and fungicide as well as blue stain protection. Dry coating thickness 70um. Tests and approvals according to ÖNORM B 3803 and ÖNORM C 2350 for wood protection of dimensionally-stable components made of wood. Adhesion force tested according to ISO Tested UV penetration of 0.9% with 80µn dry coating strength. Elasticity according to ÖNORM A 1605 test specifications for furniture surfaces. Water steam penetration according to ÖNORM C Steel frame: All side parts made of angle steel 50x40x5mm and flat steel 30x5mm material S235JRG2 - EN 10025, hot-dip galvanised according to DIN EN ISO 1461 and Ö-Norm E 4015, minimum coating thickness according to DIN 50976, surfaces polished and free of zinc barbs and other unevenness; stained, chromated with 6-value chrome; coated with a high-temperature coating with structure surface due to Teflon particles for exterior use, UV-stable, coating thickness according to ISO 2360, adhesion force according to ISO 53151, crosscut adhesion value GT2, colour tone Graphite grey similar to DB 703 iron mica or RAL Connection technology: Connection of the side parts with the wood slat using M6 counter-sunk safety screws with hexagonal recess and die insert according to DIN 7991 Inox A2 as well as threaded sleeve M6. Connection of the slats to the flat steel struts with wood screws with six-lobe 5x30 hot-dip galvanised blue. Mounting of the side parts on a wall with M8 cylinder screw with hexagonal recess according to DIN 912 Inox A2 and dowel Fischer M8. public design GmbH - Hanuschgasse 1 Objekt Bad Vöslau - Austria - office@.com -