COFFEE TABLE WITH RECESSED TRAY
|
|
- Jane Goodman
- 6 years ago
- Views:
Transcription
1 COFFEE TABLE WITH RECESSED TRAY Why not treat your guests to a tray laid with delicacies and then remove it from sight in your new coffee table. There's no easier way to show that you are a thoughtful and original host! All joints, both in the tray and in the table, are simple screw joints and are therefore visible. The elaborate feature of our design is the fact that the tray is set into the table. By the way: You can also make the coffee table without the tray insert; in this case, there is no need for a router. The following assembly instructions are for 20-mm-thick beech glued laminated timber board. You must adapt the list of materials accordingly if you opt for other materials or thicknesses. Ask your DIY store or carpenter to cut the required boards to size. Instructions 1. Join the table sides to make a frame
2 Bed joints are screw brackets with short arm lengths (in this case, 22 and 28 mm) and a large overall height (in this case, 127 mm). The bed joints are used to combine the short sides and the long sides of the table together so that they form a single frame. The short sides are enclosed by the long sides in this frame. The metal fittings are positioned so that the long arm is screwed together to the short side and the short arm is screwed together to the long side. Bed joints guarantee that the joints are particularly robust; however, you can also use other screw brackets for assembly. Fit the parts using the cordless screwdriver and flat head screws (4 x 15 mm). 2. Make the tray cutout in the table top
3 Using a pencil, mark a rectangular cutout measuring 280 x 430 mm for the tray on the table top, according to the specifications in our illustration. Make a hole in each of the corners using the drill and 10-mm wood drill bit. The outline of the holes must only barely touch the pencil lines, not intersect them. Insert the saw blade of your jigsaw in one of the holes while it is switched off. Now saw the cutout from one hole to the next. Since a jigsaw will never cut in a straight line without a stop, you should always remain within the pencil line when sawing. This way, you can smooth any bumps afterwards with a wood file and sanding paper. Experienced assemblers can cut 3 mm inside the line and then go back and refine the cut with the router at the parallel guide. This process will give the cutout perfectly straight edges. Finally, use the jigsaw to straighten the corners rounded by the boreholes. 3. Join the table top and frame together
4 Place the table top on your work surface with the upper surface facing downwards. Arrange the preassembled frame on top of it so that it lies flush with the table top. Now screw the remaining four bed joints axially with all four sides of the frame and the table top. For this purpose, use a cordless screwdriver and flat head screws (4 x 15 mm). 4. Prepare the inner side panels of the tray insert Since we have assembled the table top and side panels using bed joints and the insert for the tray is close to one of the narrow table side panels, we must mount the bed joints flush in the upper edge of the short side of the insert (see the detail in our illustration). This means that you must rout a U-shaped notch that is 2 mm deep and 15 mm wide in the upper edge of the short side of the insert. Before starting to rout, determine which of the surfaces of the insert side panels will face inwards (and thus be visible later) when screwed to the frame. Then place the right short side panel of the insert with the outer surface facing downwards on the backing board which you have previously secured on your work surface with clamp clips. (If you are lucky enough to have a work bench, clamp the backing board in place using the bench stop.) Now screw the short side panel of the insert tightly on the backing board; position each of the screws 10 mm inside the edges of the narrow panels and 2.6 mm inside the edges of the long side panels. This will ensure that the holes are concealed after assembly. Adjust the router with the 12-mm straight bit to a routing depth of 15 mm (= width of notch required). Rout a notch that is 5 mm deep with the aid of the parallel guide. 5. Join the tray insert sections together
5 Position the insert side panels on your work surface again in the way they will be fastened together. Using a pencil, trace the outlines of the short side panels of the insert on the inside of the long side panels, mark two holes in the centre in each case, drill the holes and countersink these from outside. You can now assemble the tray insert side panels using the cordless screwdriver and screws (3.5 x 40 mm). Tip for screwing together two pieces of wood In the piece where you want to insert the screws first, always predrill a hole that is 0.5 to 1 mm larger than the screw diameter; the hole should be countersunk for the screw head. In the piece that you are going to drill second, predrill a hole that is always 1 mm smaller than the screw diameter. To fasten the base, lay the assembled frame on its upper edge and align the base around all edges so that it is flush with the frame. Using the cordless screwdriver and screws (3.5 x 40 mm), fit the frame and base. Before doing so, refer to our tips in the previous section on screwing together two pieces of wood. 6. Mount the tray insert below the table top
6 Place the table top on trestles with the visible surface facing downwards. Arrange the tray insert on top of the opening. The 8-mm-thick spacer bars must fit exactly in the spaces between the insert and table panels. Screw together the tray insert with the three abutting table side panels through the spacer bars, using screws (4 x 45 mm). For this purpose, you can use the screwholes that were required earlier to rout the notch. Refer again to our tips on screwing together two pieces of wood. 7. Assemble the tray First use the drill and 28-mm Forstner bit (wood drill bit with diameter greater than 12 mm) to insert the handle openings in the short tray sides. To do this, use a pencil to mark the drilling points on which you will focus the centring tip of the drill bit, following the specifications in our illustration. Drill the holes, ideally on the backing board that you have already used for routing the side of the tray insert. Place the tray sides together in the way you want to assemble them. Using a pencil, trace the outlines of the short sides of the tray on the inside of the long sides, mark two holes in the centre in each case, drill the holes and countersink these from outside. You can now assemble the tray sides using the cordless screwdriver and screws (3.5 x 40 mm). Refer to our tips on screwing together two pieces of wood in step 5. To fasten the tray base, lay the assembled frame on its upper edge and align the base around all edges so that it is flush with the frame. Using the cordless screwdriver and screws (3.5 x 40 mm), fit the frame and base. Before doing so, refer again to our tips on screwing together two pieces of wood. 8. Assemble the pedestal base and fasten with screws under the table top
7
8 First reduce one of the pedestal boards in length from 260 to 190 mm. (If you have chosen another depth for the tray insert, adjust this measurement as required.) Then use the jigsaw to create a recess in the upper edge of the cross connector until the tray insert slips in. Using a pencil, draw the outline of the recessed area measuring 500 x 70 mm in the upper right-hand corner of the cross connector and cut out the rectangular section with the jigsaw. To fit the pedestal boards and cross connector, start by positioning these together in the way you want to screw them together. Using a pencil, trace the outlines of the cross connector on the inner-facing surfaces of the pedestal boards and in each case, mark two drilling positions centrally. Drill the holes and countersink these from outside. Using the cordless screwdriver and screws (4 x 60 mm), fit the pedestal board to the cross connector. First screw the eight L-shaped brackets to the pedestal base so they are flush with the upper edge. Finally, fit the pedestal base below the table top using the cordless drill and screws (3 x 16 mm). Little tip To improve stability, you can insert and tighten two flat head screws (6 x 80 mm) through the cross connector into the table cavity. 9. Sand wood surfaces Take time to prepare the surfaces so they are in the best working condition possible before starting assembly.
9 First chamfer all edges with sanding paper with a grit of 120 or 180 at a 45 angle to create a small bevel. Use your sander to sand all visible surfaces in the direction of the wood grain, first with coarse sanding paper (grit of 120, 180) and then with fine sanding paper (grit of up to 240). Damp sponge the surfaces afterwards to wipe off the dust. Some loose wood fibres may protrude while the wood is drying. You can remove these with sanding paper with a grit of 180. The wood is now ready for surface treatment. Little tip: Make sure that the sanding paper is sharp enough to remove the wood fibres properly, not just flatten them. 10. Treat the surfaces with oil or wax First read the manufacturer's safety and handling instructions thoroughly. Make sure the room you are working in is well ventilated and not used for smoking, eating or drinking. Generously apply the oil or wax with a fine spray system and remove any excess with a cloth. Observe the drying times specified by the manufacturer. If you want to apply a second coat of wax, you need to sand the surface between coats using sanding paper with a grit of 240. (A second layer of oil is often applied without resanding the surface.) Once again, you must always sand in the direction of the wood grain. Repeat the application as described in the section above. Once the wax has dried, polish the surface with a soft brush until it gleams. Safety note
10 Following the wax application, spread out the wax cloth and leave it to dry properly in a well-ventilated area. If left scrunched up in a ball, the cloth may become warm and selfignite. For great DIY advice and power tools visit
Coffee table with recessed tray
Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction
More informationAsk your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles
KITCHEN TROLLEY Next time you're whipping up some magic in the kitchen, take advantage of our willing assistant. Fixed on rollers to provide easy mobility, our kitchen trolley can be stationed wherever
More informationRobert Bosch GmbH. Minimalist washstand
Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to
More informationDIY CHILD S STOOL. Instructions
DIY CHILD S STOOL Children have their own special world. And having the right furniture is part of that world. We have designed an easy-to-assemble child's stool that you can paint in a selection of bright
More informationRobert Bosch GmbH. Lounge light fixture
Lounge light fixture Nice and relaxing Lounge light fixture Light has an important effect on mood. This cool light fixture is perfect for creating a cosy lounge atmosphere. 1 Introduction This cool light
More informationRobert Bosch GmbH. Wall organiser
Wall organiser The organisational talent Wall organiser Say goodbye to messiness! The wall organiser is the ideal place to store everything that tends to lie around. 1 Introduction Wardrobes, drawers and
More informationMLCS Instructions for Bowl and Tray Template Kit #9176/#9179
MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press
More informationCactus Routed Bowl. MLCS Items Needed:
Cactus Routed Bowl MLCS Items Needed: Cactus Bowl and Tray Template #9188 Top Mounted Bearing Dish Cutter Router Bit #7817 1/2 Router Collet Extension and Wrenches #9465 45* Degree Chamfer Bit #7676 1-3/8
More informationSideboard. Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial
Sideboard Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial design. 1 Introduction From multi-material to one of a kind!
More informationChili Pepper Routed Bowl
Chili Pepper Routed Bowl MLCS Items Needed: Chili Pepper Bowl and Tray Template #9189 Top Mounted Bearing Dish Cutter Router Bit #7817 1/2 Router Collet Extension and Wrenches #9465 3/16 Radius Round Over
More informationBuild A Cedar Chair And Ottoman
Build A Cedar Chair And Ottoman If you've ever dreamed of extending the comfort of your living room to your deck, patio or yard, our porch chair-and-ottoman combination is a great place to start making
More informationARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationContents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops
Contents pages 2-8: Installing Edge sinks into custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops pages 9-14: Installing Acrylic sinks into custom laminate countertops
More informationTHE PODIUM MUSIC STAND
THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationCurium 19H Installation Instructions & Parts List
Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationJigsaw Puzzle Tray. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationMortisting Stand. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Mortisting Stand Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos.
More informationOUTDOOR STOOL. ProWood Project Plan
ProWood Project Plan OUTDOOR STOOL With ProWood Professional Grade pressure-treated wood, you can easily build this sturdy stool and complement your outdoor deck, patio or yard furniture and expand your
More informationDubnium 11 Installation Instructions & Parts List
Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.
More informationGallium 03 Installation Instructions & Parts List
Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed
More informationPre-Paint>Wings>Fit ailerons. Objectives of this task: Materials and equipment required: Size the ailerons and pre-mould strips
Pre-Paint>Wings>Fit ailerons Objectives of this task: In this task the ailerons and the pre-mould strips will be sized and trimmed, then flocked onto the wings and glassed in place, and the next day the
More informationBUILDING A TREE BENCH
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own tree bench and paint it perfectly. 1 SIDE PIECES OF THE SEATING SURFACE Purchase the materials from the enclosed list. Draw a 10
More informationDowelling joints with VS 600
No. 112 Dowelling joints with VS 600 A Description Dowelling joints with round dowels (in addition to flat dowels) are part of the standard wood joints in furniture manufacture. This joint is very stable.
More information3Insert the second rod no. 4
Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue
More informationProject Plans Kreg Tool Company/BuildSomething. All Rights Reserved.
BY Project Plans ONE-OF-A-KIND CUTTING BOARD This solid-maple cutting board offers ample space for cutting and a comfortable handle, but the most-unique feature lies underneath. A cutout in the lower layer
More informationHow-to-Install. Laminate Countertops and Sheet Laminate. FREE brochure Reverso en español
FREE brochure Reverso en español How-to-Install Laminate Countertops and Easy to install instructions provided inside Multiple colors available for unique design options Durable and easy to care for Accessory
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationCurium 19.4H Installation Instructions & Parts List
Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationBONDO PROCESS. Installation Guide.
BONDO PROCESS Installation Guide www.karran.com BONDO PROCESS This Installation Guide demonstrates simple methods and proven techniques for seamlessly installing Karran undermount sinks in laminate countertops.
More informationINFINITE RANGE - HINGE DOOR
INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More informationServing Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate
Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to
More informationApartment Dining Table
Jeff Branch WOODWORKING You Can Build an Apartment Dining Table By JEFF BRANCH H ave you ever found yourself wanting a new piece of furniture, but everything you see in stores is too big? Big furniture
More informationBen Franklin 5&10 Store
Ben Franklin 5&10 Store RIVER LEAF MODELS, LLC RIVER LEAF MODELS, LLC Thank you for purchasing the Ben Franklin 5&10 structure kit. Your kit includes everything you need to assemble the final product.
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationEZYSTONE WORKSURFACES
EZYSTONE WORKSURFACES Installation & Maintenance Instructions 1. Tools Required Worktop Edge Finishing Kit Pack 1-100mm Velcro Backing Pad Pack 2-100mm Diamond Dry Cut Velcro Discs (100 Grit Yellow) (200
More informationKlamp Trak. Instructions (39052)
Klamp Trak TM Instructions (39052) ITEM# KKS1020 - Klamp Trak TM Getting Started There are three main methods for installing Klamp Trak in your workshop. In all three methods, your goal will be to construct
More informationWOODWORKING GUIDE: BASIC JOINERY
WOODWORKING GUIDE: BASIC JOINERY Close isn't really good enough. A perfect fit is what counts. When building furniture, there are many ways to construct joints. The simplest are those that use mechanical
More informationQWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS
QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationRetrofit Apron Front Farm Sink With Dual Mount Capability Installation Instructions
For Under-Mount Installation please refer to page 14 FOR EXPERIENCED AND PROFESSIONAL INSTALLATION ONLY This installation project is designed for an advanced skill level. Disclaimer: Undermount Application
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 2
Kentucky 4H Wood Science Plans Notebook Plans Level 2 MATERIALS NEEDED: JEWELRY BOX WS201 1 piece wood 1/4" x 4 x 4 1/2" (bottom) 1 piece wood 1/4" x 4 1/2" x 5 (top) 2 pieces wood 1/4" x 2 x 5 (front
More informationFLOW HIVE ASSEMBLY GUIDE. If we look after the bees they will look after us, and the honey really is an amazing bonus. Flow Hive Hybrid 3 Frame
AUSTRALIAN MADE If we look after the bees they will look after us, and the honey really is an amazing bonus. FLOW HIVE ASSEMBLY GUIDE Flow Hive Hybrid 3 Frame Read all instructions first. If you are unfamiliar
More informationQWALL 5.2 (2 Back Panels)
QWALL 5. ( Back Panels) SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationInstallation Guide 1
1 2 Contents Before you begin Storage & preparation Tools & materials you may need Getting started Sink & cooktop cut-outs Cabinet Joins for 20mm benchtops Joining & installation of 20mm benchtops Joining
More informationBUILDING A GOAL WALL DO IT YOURSELF! INSTRUCTIONS FOR A GOAL WALL
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own goal wall and paint it perfectly. COMPILED BY 1 PREPARING Purchase the materials from the enclosed list. The DIY store should be
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationADULT. Adirondack / Muskoka Chair Plans
ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also
More informationInstall Instructions for Torrance Jurastone #4004 Mantel
Install Instructions for Torrance Jurastone #4004 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. 20/05/11 Fires of Tradition assumes no responsibility
More informationPROJECT PLAN MODERN COFFEE TABLE
BUILD IT WITH ROCKLER PROJECT PLAN MODERN COFFEE TABLE With its clean lines and striking geometry, this coffee table will lend iconic midcentury modern style to any living space. And you can build it yourself
More informationThis tailor s cabinet was brought to my attention by a customer
So what if you don t sew? This authentic Shaker case piece is drop-dead gorgeous in any room. This tailor s cabinet was brought to my attention by a customer who wanted one just like it. She had seen the
More informationXenon 05 Installation Instructions & Parts List
Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationSeamed Undermount Bowls
CUTOUT TEMPLATES MAKING CUTOUT TEMPLATES 7.1 CUTOUT TEMPLATES The use of an accurate template is one of the most essential elements to the successful completion of a cutout in Corian. For the completion
More informationInstall Instructions for Solano Jurastone #4012 Mantel
Install Instructions for Solano Jurastone #4012 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. Updated 12/03/12 NOTE the installation requirements
More informationProject Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen
Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood
More informationOUTDOOR COOLER STAND. ProWood Project Plan
ProWood Project Plan OUTDOOR COOLER STAND With ProWood Professional Grade pressure-treated wood, you can easily build this sturdy outdoor cooler stand and expand your family s backyard fun. This project
More information(1) C & C 30 MK I I. Building the Wine Glass Holder
(1) C & C 30 MK I I Building the Wine Glass Holder 1. This package contains instructions and sketches plus scanned pictures. 2. Woodworking skills and equipment are essential to make the pieces and assemble
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: (3) 4x4x8 Ft. Boards (8) 2x4x8 Ft. Boards 2 ½-inch Pocket Screws 2 ½-inch Wood Screws 1-inch Wood Screws (16) Figure 8 Tabletop Fasteners Wood Glue Wood Filler TOOLS: Tape Measure Pencil Carpenter
More informationRECOMMENED TOOLS FOR MACHINING COUNTERTOPS
Fabrication Manual RECOMMENED TOOLS FOR MACHINING COUNTERTOPS 1. Blades a) Segmented blade for porcelain. 4. Polishing Discs a) Silicon Carbide velcro discs for dry use. Grit 60, 120, 220, 400. 2. Grinding
More informationEssential BOX JOINT JIG
Essential BOX JOINT JIG Home in on precise finger joints with this table saw sled. By Ken Burton The box (or finger) joint is a remarkably strong, interlocking corner joint that can be quickly made on
More informationRadon 07 Installation Instructions & Parts List
Radon 07 Installation Instructions & Parts List Illustration Radon 07, H1 Handle Right Hand: Open Out 14/06/2016 Revision 1.1 Page 1 of 21 IMPORTANT This shower screen / enclosure must be installed by
More informationProduct must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.
General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR ONLY ( RECESS) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationScratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout
Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout By Dwight Ennis In this section, we're going to make the Frost Box, and we'll build the Spout Hanger Assembly
More informationHow To Create An Entertainment Unit
How To Create An Entertainment Unit Materials required: 2 x Pine Panels - 1800mm x 450mm x 18mm 4 x Pine Panels - 310mm x 450mm x 18mm 1 x Pine Panels - 650mm x 450mm x 18mm 6 x Bun feet (your choice of
More informationHM OUTDOOR TABLE:HM OUTDOOR TABLE 25/7/08 11:18 AM Page 30
HM080827 OUTDOOR TABLE:HM080827 OUTDOOR TABLE 25/7/08 11:18 AM Page 30 The treated-pine frames of the table and benches are topped with sturdy blackbutt timber. HM080827 OUTDOOR TABLE:HM080827 OUTDOOR
More informationOakland II POCKET BILLIARD TABLE INSTALLATION MANUAL
TM Oakland II POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 EMAIL: BRUNSWICKSERVICE@BRUNSWICKBILLIADS.COM 51-906253-000 OCTOBER 2016
More informationREVISION LIST CHAPTER 25: AFT WINDOWS. The following list of revisions will allow you to update the Legacy construction manual chapter listed above.
REVISION LIST CHAPTER 25: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More information136 PLYWOOD DESK 522
136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationBalustrade Systems / Installation Instructions
A. PARTS AND SUPPLIES NEEDED FOR INSTALLATION Hardware included for each 10 section of rail: 2 3 x 1-1/2 L-brackets 4 1-3/4 x 3/16 Blue hex-head screws for anchoring the L-brackets to the newel cap, column
More informationInstall Instructions for Corvallis Jurastone #4008 Mantel
Install Instructions for Corvallis Jurastone #4008 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. Updated 12/03/12 NOTE the installation requirements
More informationInstallation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( )
Installation Guide A Subsidiary of Panolam Surface Systems SMPBRO00-012 6/14 Pionite decorative laminates are designed for finished interior surfaces which require high impact, wear and stain resistance
More informationMAGNUM BOARD INTERIOR INSTALLATION GUIDELINES
TECHNICAL BULLETIN No.: 090509-1405 Subject: Issue Date: September 4, 2009 Issue No.: II MAGNUM BOARD INTERIOR INSTALLATION GUIDELINES 1. CUTTING MAGNUM BOARD You can easily cut Magnum Board with carbide
More informationClassic Mitered Jewelry Box
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationProject 13586EZ: Writing Desk. Writing Desk Materials List
Project 13586EZ: Writing Desk This writing desk will make a handsome addition to just about any room in the house. The one shown is made of cherry, a logical choice for a piece like this, but mahogany
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationPRODUCT INFORMATION MANUAL SECTION: 9F-1 DUETTE ULTRAGLIDE LIFTING SYSTEM DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM
DUETTE SIGNATURE ULTRAGLIDE LIFTING SYSTEM Product View Installation Brackets UltraGlide Standard Wand Top-Down/Bottom-Up Duolite REPLACES ISSUE DATE: APPROVED BY: D.ALTIPARMAKOVA PAGE 3 Thank you for
More information30 FINE woodworking. Photo, this page: Michael Pekovich
30 FINE woodworking Photo, this page: Michael Pekovich Arts & Crafts Bed White-oak bed is loaded with Stickley style and topped off with traditional inlay by Kevin Rodel This bed design is a close copy
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationTreviso POCKET BILLIARD TABLE INSTALLATION MANUAL. SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104
Treviso TM POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 51-905881-000 NOVEMBER 2008 NOTE: Please use the instructions in this manual
More informationBasic Assembly For Conventional Series 9000 Structural Panels
Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Basic Assembly For Conventional Series 9000 Structural Panels NOTE: Assembly directions for curved panels are the same as standard panels. Tools
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More information1Use the metal file to smooth
Yamato: Step-by-step 85 Parts of the bridge and the hull a b c d e f a Part of the bridge b Part of the bridge c Part of the bridge d Radar x 2 e Part of the bridge x 2 f Wire Recommended tools and materials
More informationShopsmith Mobile Storage Cabinet.
http://wwwinstructablescom/id/shopsmith-mobile-storage-cabinet/ technology workshop living food play outside Shopsmith Mobile Storage Cabinet by Beave2012 on May 3, 2015 Table of Contents Shopsmith Mobile
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More information