VIGO - COLUMN SYSTEM

Size: px

Start display at page:

Download "VIGO - COLUMN SYSTEM"

Martin Hodge
6 years ago
Views:

1 VIGO - COLUMN SYSTEM

COMPONENTS 6 7 3 2 17 15 12 14 11 13 15 10 16 9 8 1 2 5 1 4 1 - Column system stile 2 - Column system LED cover 3 -

- 9 - Shelf support mount 10 - Double-sided shelf support 11 - Single-sided shelf support 12 - Glass shelf mount 13-400

2 COMPONENTS Column system stile 2 - Column system LED cover 3 - Column system cover 4 - Column plug 5 - Column mount 6 - Column wall support 7 - Column angle connector 8 - Chrome stand Shelf support mount 10 - Double-sided shelf support 11 - Single-sided shelf support 12 - Glass shelf mount mm support rail 14 - Rod mount 15 - Oval rod 16-18mm shelf (board) 17-8mm shelf (glass) mm shelf (board) 8mm shelf (glass) 1

3 ASSEMBLY INSTRUCTIONS 1 Assembly options: 2 Calculate the dimensions: H - installation height S - installation width h - stile height s - shelf width n - number of column sets H h = H-53mm S-(40 x n) s = n -2 in case of a board shelf s = distance between column sets -2 mm S-(40 x n) s = n -18 in case of a glass shelf s = distance between column sets -18 mm In case of assembling the column floor-to-wall the length of the column stile needed to connect the column to the wall is calculated as follows: A - distance from the column front to the wall a - length of column stile a=a-10 mm S A a 2

4 ASSEMBLY INSTRUCTIONS 3 Floor-to-ceiling column assembly. 5 Shelf support mount assembly. 1. Attach the column plug to the ceiling. 2. Insert the column into the plug and fasten it using the expansion screw of the stand. 1. Using a hex key place half of the shelf support mount on the mounting rail of the column stile. 2. Fasten the firming screws of the support mount. 3. Similarly assemble the other part of the support mount. 1. Notice: the screws firming the support should be facing down in both halves of the support mount Floor-to-wall column assembly. 1. Connect the column stiles cut at a 45 angle using the column angle connector and fasten the firming screws in the connector. 2. Insert the column into a plug with a column mount attached to the floor. 3. Insert the column into a plug with a column wall support attached to the wall. 4. Fasten the column to the mount and the wall support using the supplied screws Shelf support assembly. screws firming the support mount 1. Insert the shelf support into the support mount 2. Fasten the support using firming screws. Notice: The double-sided shelf support should be assembled with the firming screw notches facing up. The single-sided support has firming screw notches on both faces. 3. firming screw notches

5 ASSEMBLY INSTRUCTIONS 7 Shelf assembly. 9 Screw the glass shelf mount to the glass shelf and fasten it using firming screws. Next attach the shelf with the mounts to the shelf support using the screws from the shelf mount set. Screw the shelf directly to the shelf support using appropriate screws. Column stile cover assembly. Cut the cover to a length equal to the distance between the relevant shelves. Push the cover into place. The cover with a LED tape groove is assembled in the same way as the cover without a groove. A standard LED tape can be slid into the cover with a LED tape groove. The holes in the shelf supports allow to lead the LED tape through them without cutting the tape. 8 Rod assembly. Rod length = distance between columns - 4mm Attach the rod mount to the column stile using appropriate screws. Next insert the rod into the mounts. 4

6 SYSTEM COMPONENTS Column system stile 5,6 m Column mount SK-0087-SR SK-SKP01D-00 aluminium Anodizing width: 15 microns Available length: 550 cm Available colours: silver 2 mm steel sheet Column system LED cover M-LED Column wall support SK-SKP transparent plastic Available length: 260 cm, LED tape assembly 2 mm steel sheet Column system cover M-KOL Column angle connector SK-SKK00-00 transparent plastic Available length: 260 cm ZnAl Column plug SK-SKP01-00 Chrome stand - ST-KOL-00 ZnAl steel, plastic 5

7 SYSTEM COMPONENTS Shelf support mount 400 mm Support rail SK-SKZ00-00 ZnAl SK-SKW01-00 aluminium Anodizing width: 15 microns Available length: 40 cm Available colours: silver Double-sided shelf support Oval rod mount SK-SKU01-00 UCH-DR mm steel sheet chrome steel oval rod mount Single-sided shelf support SK-SKU01S-00 3 mm steel sheet 3 m Aluminium oval rod DROW AA aluminium Available length: 300 cm Available colours: silver column system, wardrobe interiors Glass shelf mount SK-USK00-00 ZnAl 6

8 QUAMIRO SP. Z O.O. Karpin Dąbrówka tel. (22) mob , fax. (22) info@quamiro.pl

WALL SHELVING SYSTEM 250/750

WALL SHELVING SYSTEM 250/750 468 2/7 Installation Example Ceiling Height (CH) : 2800 mm Ceiling Height (CH) : 28 mm Corner Installation 2 design panels are used to cover mm space in case of ceiling height 28 mm. Corner Example 469