NURABOND LOW FOAMING PU ADHESIVE TECHNICAL DATA SHEET
|
|
- Amber Smith
- 6 years ago
- Views:
Transcription
1 53 A Victoria Street Onehunga Auckland Phone NURABOND LOW FOAMING PU ADHESIVE TECHNICAL DATA SHEET DESCRIPTION AND USE Nurabond PU Adhesive is a ready to use, high performance, single component, moisture curing polyurethane adhesive for bonding Nuratech TPE SG fleece backed polymeric single ply membranes to rigid insulation, concrete, bitumen membranes and other suitable substrates. The adhesive is cold applied and has been specially developed to allow safe and rapid bonding of suitable membranes. APPLICATION Substrates must be clean and free from any liquid water although damp surfaces are acceptable. The adhesive should not be used in temperatures below 5 C or above 30 C as the working time will be dramatically reduced. To allow the adhesive to cure the relative humidity should be a minimum of 30%. In hot, dry conditions it may be necessary to lightly moisten the substrate with a fine spray of water prior to applying the adhesive. The adhesive is poured onto the substrate direct from the container and spread evenly at the coverage rate specified using a roller or squeegee. The product will become milky and start to bubble. At this point the adhesive should be left exposed for at least 10 minutes to allow solvent to escape. Roll the single ply membrane into the adhesive and consolidating to ensure good contact by brooming the surface area. Nurabond Low Foaming PU Adhesive cures within 6 hours. As the product is moisture curing, ensure the cap is firmly placed on the container when not being poured from. Do not return previously decanted adhesive to the container as it will start to cure in the drum. CLEANING To clean tools and splashes of wet adhesive use spirit based cleaners. COVERAGE RATE One 6kg pail covers approximately 20m2 although additional adhesive may be required depending on the temperature, surface texture and porosity. PACKAGING Nurabond Low Foaming PU Adhesive is supplied in 6kg containers
2 STORAGE In cold conditions Nurabond Low Foaming PU Adhesive should be stored at a minimum of 15 C prior to use to aid application. If material is stored on the roof or externally the adhesive can be maintained at a usable temperature by storing in a heated tank of water. This product should be stored in its original sealed container at a temperature between 5 C and 25 C. Nurabond Low Foaming PU Adhesive is flammable and should be kept away from sources of ignition. TECHNICAL DATA Chemical Type: Polyurethane Appearance: Clear cures to yellow Odour: Solvent Viscosity: 3000cps@20 C Solid Content: 77% HEALTH & SAFETY Nurabond Low Foaming PU Adhesive is a hazardous product. Wear suitable protective gloves and ensure adequate ventilation during use. Refer to the safety data sheet for Nurabond Low Foaming PU Adhesive. SHELF LIFE The adhesive has a shelf-life of 6 months when stored in these conditions. IMPORTANT NOTICE: The above recommendations are intended for the assistance of users and are of a general nature. They are based on our experience and judgement but because the conditions under which, and the materials with which our products are used, are beyond our control our recommendations must not be regarded as amounting to legal warranty or as involving any liability on us.
3
4 53 A Victoria Street Onehunga Auckland Phone NURABOND TPE CONTACT ADHESIVE TECHNICAL DATA SHEET DESCRIPTION AND USE Nurabond TPE Contact Adhesive is a ready to use synthetic rubber based, contact adhesive for adhering TPE roofing membranes onto various substrates. It is easy to apply using brush or roller and is specifically used to adhere Nurabond TPE membranes to various substrates at upstands and details. APPLICATION Nurabond TPE Contact Adhesive is suitable for adhering TPE roofing membranes to various substrates including wood, steel and concrete. Substrates must be clean, dry and degreased and the adhesive must only be used in dry conditions at temperatures of at least 5 C. Condensation on surfaces must be avoided as this will greatly impair adhesion, freshly applied adhesive should be protected from draughts to prevent condensation forming whilst the adhesive is drying. Nurabond TPE Contact Adhesive should be applied to both surfaces with a brush or roller. Porous surfaces may require a second adhesive layer. The layer of adhesive applied to the substrate should be allowed to dry completely. The layer of adhesive applied to the membrane should be allowed to dry until tacky to the touch. Both applications of adhesive should be allowed to dry for a minimum of 5 minutes to allow solvents to disperse before bringing the glued surfaces together. After bonding, apply pressure to the bonded area using a hand roller. The adhesive is not suitable for sealing lap joints. All lap joints must be hot air welded. CLEANING To clean tools and splashes of wet adhesive use spirit based cleaners. COVERAGE RATE The adhesive should be applied to each surface (membrane and substrate) at a combined rate of 10m2 per 5 kg tin, depending on temperature and surface porosity. A 40sqm roll of Nuratech TPE SG requires approximately 4 pails of Nurabond TPE Contact Adhesive.
5 PACKAGING Nurabond TPE Contact Adhesive is supplied in 5kg containers STORAGE Nurabond TPE Contact Adhesive is flammable and should be kept away from sources of ignition in original sealed containers at a temperature between 5 C and 25 C. HEALTH & SAFETY Nurabond TPE Contact Adhesive is a hazardous product. Wear suitable protective gloves and ensure adequate ventilation during use. Refer to the safety data sheet for TPE Contact Adhesive. SHELF LIFE The adhesive has a shelf-life of 12 months when stored in these conditions. IMPORTANT NOTICE: The above recommendations are intended for the assistance of users and are of a general nature. They are based on our experience and judgement but because the conditions under which, and the materials with which our products are used, are beyond our control our recommendations must not be regarded as amounting to legal warranty or as involving any liability on us.
NOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY).
Product Description PHOENIX PAINTS MAXICOAT 100 is a 2 Pack Water-Dispersed Top Coat which not only exhibits the physical and chemical strengths of epoxy, but also the safety and convenience of water as
More informationFurniture Adhesives.
Furniture Adhesives www.romaplastik.com Roma Plant, Gebze/Turkey ROMA HISTORY AND ROMA TODAY Founded in 1996, Roma Plastik is the world s 3 rd largest edging manufacturer and the market leader in Turkey,
More informationFABRICATING ARBOR. koroseal.com/arbor Arbor Veneered Components
Arbor Veneered Components Arbor natural wood veneer can be applied to any substrate and is flexible enough to be formed around the tightest radii providing the ultimate wood finish. From vertical wall
More information3.4 Wall Flashing Wall Flashing General
3.4 Wall Flashing 3.4.1 Wall Flashing General The wall flashing details are in line with the two methods of base tie-in, previously described. Either the field membrane has to be spliced onto the QuickSeam
More informationFix-R EPDM Installation Guide. Field Installation Guide
Field Installation Guide 1 CONTENTS General Information & Precautions 3 Tools, Equipment & Roof Surface Preparation 4 Membrane Installation Installation of Fix-R EPDM roofing 5/6 Base Tie-in Detail 7/8
More informationClassicBond Installation Guide. Field Installation Guide
Field Installation Guide 1 CONTENTS General Information & Precautions 3 Tools, Equipment & Roof Surface Preparation 4 Membrane Installation Installation of ClassicBond roofing 5 & 6 Base Tie-in Detail
More informationLow V.O.C. 2-Component Polyurethane Game Line Paint System
PBWWinc. 1 Technical Data Sheet GEN-U-LINE 4000 Series Low V.O.C. 2-Component Polyurethane Game Line Paint System Product Description: GEN-U-LINE 2-component polyurethane line paints are high gloss, flexible,
More informationSketchpaint. Ideal for turning any smooth surface into a whiteboard. Ready to use in 5 days
Sketchpaint Ideal for turning any smooth surface into a whiteboard SketchPaint - A whiteboard straight out of a tin! White Gloss or Transparent Finish Simple application Tin size available: 3m² or 6m²
More informationMagnetpaint & Sketchpaint
Magnetpaint & Sketchpaint Turn any smooth surface into a magnetically receptive whiteboard MagnetPaint is an exciting product that allows you to paint your own magnetic surface on any flat area. SketchPaint
More informationTOOLS & SUPPLIES (Included in ProTops Tool Kit)
TOOLS & SUPPLIES (Included in ProTops Tool Kit) Clean Paint/Mixing Sticks Graduated Mixing Buckets Standard Mixing Cups Nylon Paint Brush Propane Torch 3M Masking Gun Masking Film & Painter s Tape Disposable
More informationPBWWinc. GEN-U-LINE 4000 Series Application Guide. Technical Data Sheet. General Guidelines:
PBWWinc. 1 GEN-U-LINE 4000 Series Application Guide Technical Data Sheet General Guidelines: 1) Close the facility to all traffic before starting any work on the game lines. Close all doors and windows
More informationRoll Out Vinyl Installation Guide
Sub-floor Requirements The contractor performing the installation of the performance vinyl flooring must ensure the proper quality of the sub-floor. The sub-floor must be clean, smooth, permanently dry,
More informationClassicBond Installation Guide. Field Installation Guide
Field Installation Guide 1 CONTENTS General Information & Precautions 3 Tools, Equipment & Roof Surface Preparation 4 Membrane Installation Installation of ClassicBond roofing 5 & 6 Base Tie-in Detail
More informationAnti-Graffiti OVERVIEW OUR PRODUCT VS. CONVENTIONAL CLEANERS.
Technical Application Sheet Version:2.01 Edition:01/8/2015 Anti-Graffiti Anti-Graffiti OVERVIEW OUR PRODUCT VS. CONVENTIONAL CLEANERS Anti-Graffiti is a Sol-Gel based, chemical nanotechnology 2 component
More information380 Swimming Pool Paint
Issued 21 st April 2010 PRODUCT DATA SHEET UNPAINTED CEMENT 380 Swimming Pool Paint SURFACE PREPARATION New cement or render should be allowed to cure for at least 21-28 days before any preparation is
More informationTECHNICAL DATA SHEET NO: 137 VERSION: 1/31/1/03 PAGE: 1 of 5 PRINT DATE: 9/16/2004 EVERBUILD PINK GRIP
PAGE: 1 of 5 PRINT DATE: 9/16/24 EVERBUILD is a revolutionary new direct bond cartridge applied adhesive formulated specifically for the professional user, using polymers at the leading edge of adhesive
More informationRPI ROYAL EDGE EPDM MATERIAL GLOSSARY & GUIDE
RPI ROYAL EDGE EPDM MATERIAL GLOSSARY & GUIDE WHITE EPDM MEMBRANE TPO MEMBRANE WHITE EPDM MEMBRANE TPO MEMBRANE Multi-System Products: W TPO Cured field membrane used for waterproofing sidewalls, flat
More informationGlues and mastics. SILICONE ADHESIVE SEALANT 42 Marine silicone SOROMAP...42 Silicone colour RAL...42 Glue mastic MS1000 TECHNIFIX...
Glues and mastics In this chapter, we present all the products that you need to make sticking, seals, insulation and teak deck. SILICONE ADHESIVE SEALANT 42 Marine silicone SOROMAP......................................42
More informationPBWWinc. Technical Data Sheet. GERLINE Gameline Paint Instructions for Sport Flooring. General Guidelines:
PBWWinc. 1 Technical Data Sheet GERLINE Gameline Paint Instructions for Sport Flooring General Guidelines: 1) Close the facility to all traffic before starting any work on the game lines. Close all doors
More informationPrefere 4040 is approved for the use in production of load bearing timber structures by FCBA (France).
Technical Data Sheet Use is a phenol-resorcinol adhesive that is mainly used in the manufacture of load bearing timer structures. It can also be used for products exposed to high humidity such as windows
More informationInstallation Instructions
Aspex Digitally Printed Wall Art PL PREMIUM HEAVY DUTY ADHESIVE ASPEX WALL ART DOUBLE SIDED FOAM TAPE Installation of Aspex Digitally Printed Wall Art with Foam Tape and PL Premium Adhesive. Maximum size
More informationDULUX UNIVERSAL UNDERCOAT
TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Intermediate coating for use under decorative topcoats, for interior and exterior use PRODUCT
More informationLuxCore Installation Instructions
LuxCore Installation Instructions ATTENTION: LuxCore PANELS MUST BE ACCLIMATIZED FOR 24 HOURS BEFORE INSTALLATION PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION The guidelines provided herein have
More informationFlameOff Fire Barrier Paint. Application Guide
TM FlameOff Fire Barrier Paint Application Guide FlameOff FCI Phone: (888)816-7468 Email: info@flameoffcoatings.com Web: www.flameoffcoatings.com FlameOFF Coatings, Inc. owns and certifies all data in
More informationPRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
More informationPhysical constants Finish: ASTM D Flash point: Rangan Far, s Adding thinner to a paint may change the flash point of the diluted material.
Finish: The appearance of the paint film after drying under optimum conditions,- given as high gloss (>90), gloss (60-90), semi-gloss (30-60), semi-flat (15-30), or flat (
More informationInstallation Instructions
www.marlite.com Effective Date 03/01/2018 ARTIZAN FRP, SYMMETRIX FRP, ENVUE FRP, STANDARD FRP Installation Instructions Statements expressed in this technical bulletin are recommendations for the application
More informationRead and understand the requirements of this procedure Assist students with installation as needed
1. PROCEDURE OVERVIEW This procedure is to be used for installation of bonded strain gages on reinforcing bars. It includes necessary materials and a recommended practice for surface preparation, installation,
More informationControltac Graphic Film
Controltac Graphic Film 162-10 and 162-114 Product Bulletin 162 Release L, December 2008 See Bulletin Change Summary on last page. For Screen Printing and Offset Printing Only Product Description Recommended
More informationSWARCO LIMBURGER LACKFABRIK GmbH Road Marking Systems. 1-comp. FLUOX daylight luminescent paint system TECHNICAL INFORMATION
1-comp. FLUOX daylight luminescent paint system TECHNICAL INFORMATION 1-comp. FLUOX luminescent paint system Art.-No.: 8109016 white, 1-comp. FLUOX Primer Art.-No.: 810..., colored 1-comp. FLUOX luminescent
More informationFigure 1 Photograph of a strain gage on a helical wire
1. PROCEDURE OVERVIEW This procedure is to be used for installation of bonded strain gages on prestressing strand. It includes necessary materials and a recommend practice for surface preparation, installation,
More informationStep by Step Wing Bagging
Step by Step Wing Bagging By Evan Shaw 073 589 9339 evanevshaw@gmail.com Preparing the Leading Edge 1. Cut cores. (Cutting of wing cores is covered in another article elsewhere) 2. Sand the LE to a nice
More informationUnit PO0205K Knowledge of Applying Fillers and Foundation Materials
Assessment Requirements Unit PO0205K Knowledge of Applying Fillers and Foundation Materials Content: The types of substrates likely to be found in vehicle refinishing a. List types of substrate to include:
More informationIdentifying Common Interior Paint Defects/ Complaints
Identifying Common Interior Paint Defects/ Complaints Use of low quality semi-gloss or gloss acrylic paints Use of flat paint in highly trafficked areas, where a higher sheen level would be desirable Use
More informationA strong clear liquid that bonds most materials in seconds. A quality product for the DIY enthusiast Great for emergency repairs.
Superglue Super Glue 3G - 3 s A strong clear liquid that bonds most materials in seconds. A quality product for the DIY enthusiast Great for emergency repairs. Super Glue 3G - Single A strong clear liquid
More informationNanoman Anti-Graffiti (Porous Surfaces)
Nanoman Anti-Graffiti (Porous Surfaces) Nanoman Anti-Graffiti Coating is an advanced, high performance, long lasting ONE COAT, NON SACRIFICIAL, anti-graffiti coating specially formulated to protect porous
More informationAdhesives. The tradesman s essential guide
Adhesives The tradesman s essential guide Adhesives The tradesman s essential guide Trade Essentials Adhesives Trade Essentials Adhesives are a range of high quality glues specifically designed for the
More informationIMPORTANT: This product cannot perform its intended function if not properly installed.
www.emseal.com HORIZONTAL COLORSEAL INSTALL DATA - HORIZONTAL COLORSEAL FEBRUARY 2015, PAGE 1 OF 3 INSTALLD AT DO NOT OPEN ANY PACKAGES or install this material until all members of your crew have read
More informationTechnical Data February, 2016
Technical Data February, 2016 Product Description 3M DP-600 is a non-sag, grey, rapid setting, two-component polyurethane. It is packaged as 1:1 ratio liquids in a duo-pak cartridge. With the squeeze of
More informationA. Provide a comprehensive guide to the products that are used when flashing, what they are used for, and the proper way to use them.
EPDM FLASHINGS & ADHESIVES GUIDE PART 1 - GENERAL Revised March 2017 1.01. Introduction 1.02. Scope: A. While many roofing projects are likely to have their special problems, the contractor is certain
More informationIndustrial and Transportation Business DISTRIBUTOR PRODUCT LINE
Industrial and Transportation Business DISTRIBUTOR PRODUCT LINE 3900 DUCT TAPE 3900 DUCT TAPE MRO (Maintenance and Repair) Construction Trade Shows and Conventions General Industrial Electrical Aerospace
More informationFrequently asked questions about Alcolin Waterproof Glue
Frequently asked questions about Alcolin Waterproof Glue 1. How can I lengthen the time to assemble my glued furniture? Apply adhesive to both surfaces. Of the polyvinyl acetate type adhesives, Alcolin
More informationApprox. Weight in g/m²
TECHNICAL DATA SHEET Magnetically Active glass fleece Properties / Typical application The back of glass fleece has a metallic coating. Standard, commercially available magnets therefore adhere directly
More informationARDEX Butynol. Installation Instructions. For installation of ARDEX Butynol and Butyseal
Instructions For installation of ARDEX Butynol and Butyseal ARDEX Australia Pty Ltd 20 Powers Road Seven Hills NSW 2147 Phone: 1300 788 780 Fax: 1300 780 102 Email: technicalservices@ardexaustralia.com
More informationDuPont Flashing Systems Installation Guidelines. Integral Flanged Door Before water-resistive. Version 2
DuPont Flashing Systems Installation Guidelines Helping you get the job done right Integral Flanged Door Before water-resistive barrier (wrb) is installed Version 2 Table of Contents Applicable Products...2
More informationMETHOD STATEMENT. Sika FloorJoint S
METHOD STATEMENT Table of Contents 1 SCOPE 3 2 PRODUCT 3 2.1 3 3 SUBSTRATE REQUIREMENTS 3 4 Preparation of the Substrate 3 4.1 Mapping of the joint panels on the floor for the saw cuts 3 4.2 Execution
More informationSeal Coats and Surface Treatments Fred J. Benson, Dean of Engineering A. and M. College of Texas College Station, Texas The construction, as here
Seal Coats and Surface Treatments Fred J. Benson, Dean of Engineering A. and M. College of Texas College Station, Texas The construction, as here discussed, consists of an application of bituminous material
More informationTHE PARQUET WORLD AT YOUR FEET
THE WORLD AT YOUR FEET PREPARATION BONDING FINISHING Preparation DL EGALINE PRIMER Is used as a bonding primer for DL Egaline in case of layer on layer floor levelling application or as prior primer and
More informationUNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS
UNIT REF: PO0205K UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS Level: 2 Route: Knowledge Credit Value: 6 GLH: 45 Mapping: This unit is mapped to the IMI NOS PO2 and PO5 Rationale:
More informationInstallation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( )
Installation Guide A Subsidiary of Panolam Surface Systems SMPBRO00-012 6/14 Pionite decorative laminates are designed for finished interior surfaces which require high impact, wear and stain resistance
More informationATELIER MEDIUMS. Interactive Mediums
ATELIER MEDIUMS Atelier Interactive is very simple to use: use with our traditional acrylic mediums (or water) for traditional overpainting and layering techniques. Use with our exclusive interactive mediums
More informationSelf-Adhering Reflective Sheet Membrane
application instructions preparation All surfaces must be dry and clean. Dirt, dust and any other foreign matter must be removed. TW Flash-n-wrap 40 must be applied when air, substrate, and membrane temperatures
More informationDAP 33 Window Glazing
DAP 33 Window Glazing PRODUCT DESCRIPTION DAP 33 Window Glazing is a ready-to-use glazing compound that may be used for face glazing wood or metal sash. Its knife-grade consistency allows for smooth, easy
More informationCardboard Model Buildings
Cardboard Model Buildings Get more model kits from http://www.modelbuildings.org PRINTING & ASSEMBLY TIPS: These OO designs can easily be resized by reducing the print percentage as follows: OO scale is
More informationCUPRON NEXT TECHNICAL DATA SHEET
Product description New hard matrix antifouling paint free of copper and organostannic compounds. It provides good seasonal protection for boats that work even in particularly hot and aggressive waters.
More informationDuPont Flashing Systems Commercial Installation Guidelines
DuPont DuPont Flashing Systems Commercial Installation Guidelines FOR STOREFRONT WINDOW ON A KNEE WALL AFTER WRB IS INSTALLED Table of Contents Applicable Products... 2 Recommended Materials... 2 Optional
More informationsection 9 ADHESIVES & EDGING
section 9 ADHESIVES & EDGING PHOTO 9 ADHESIVES & EDGING Adhesives & fillers 158 Edging 165 Adhesives & fillers Mitre adhesive and activator Delivers a really strong joint in a matter of seconds Suitable
More informationAPPLICATION OF JAC FILMS
1. Important points For reliable results, JAC films are best applied to smooth, dry and clean surfaces (metal, glass, paintwork, plastic etc.). It is essential to ensure that the surface is free from dirt
More informationTabletop Epoxy Resin Instruction Guide
Table Top Epoxy Full Instructional Guide WARNING! You should read through ALL of these instructions BEFORE starting. These instructions are intended for Bar Tops, Table Tops, Artwork and Countertop applications.
More informationMICRO1L / MICRO2 / MICRO6 / MICRO140UV / MICROM0
Application Guide MICROperforated Films APPLICATION AND REMOVAL Microperforated Films MICRO1L / MICRO2 / MICRO6 / MICRO140UV / MICROM0 REQUIRED ACCESSORIES QA squeegee (refer to our catalogue) QRigid for
More informationVERTICAL STILE ABOVE HORIZONTAL TRIM VERTICAL STILE BELOW COVE BASE ADHESIVE. 1" [25.4mm] BASE DETAIL
Please Read All sheet will be provided in stock sizes for field cutting. All trims will be provided in 8-0 stock lengths for field cutting. CEILING TRIM 1" [25.4mm] Acrovyn Interiors vinyl acrylic wall
More informationApplication Guide. FlameOff Fire Barrier Paint. FlameOFF Fire Barrier Paint
TM FlameOff Fire Barrier Paint FlameOFF Fire Barrier Paint Application Guide Phone: (888) 816-7468 Email: info@flameoffcoatings.com Web: www.flameoffcoatings.com FlameOFF Coatings, Inc. owns and certifies
More informationINDUSTRIAL PAINTS INDUSTRIAL TOP COAT 6 GENERAL 6 ACRYLIC LACQUERS 8 ALKYD LACQUERS 10
COLORS www.soppec.com EVENT COLORS PRO TECH INDUSTRIAL PAINTS In all industrial or agricultural activities it is important to be able to carry out rapid repairs to damaged paintwork, (notably to machinery
More informationINSTALLATION INSTRUCTIONS
VESDURA VINYL PLANKS 3MM PVC GLUE DOWN - OAK COLLECTION Safety First CAUTION Asbestos Warning in existing floor. Do not sand, dry scrape, bead blast or mechanically pulverize existing resilient flooring.
More informationSlipGrip Data Sheet & Installation Guide
SlipGrip Data Sheet & Installation Guide Stair Treads Landing Covers Flat Sheets 9/2015 SlipGrip Technical Data Description SlipGrip products are high performance safety stair treads, landing covers and
More informationClay Modeling Film. Features of Clay Modeling Film. Use Clay Modeling Film
Clay Modeling Film The series of Clay Modeling Film, originally developed by TOOLS INTERNATIONAL Corp, is mainly used for interior/exterior shape confirmation, checking highlights and qualification studies
More informationMix Ratio (by volume) 7630/3600 (Base) 0830/9000 (Acid Catalyst) Metal Primer 6840B meets the technical requirements of: Mil-P-7962 Mil-C-15328
TECHNICAL DATA SHEET Product Description 6840B is a two component chromated etch primer designed to give adhesion and corrosion protection to aluminium alloys as part of the 4080 series scheme. Alternative
More informationColor PQ GROUT TROUBLESHO TING GUIDE INSTALLATION SOLUTIONS F OR T I L E A N D STO N E.
NA NA4600 4600 Color PQ TM Premium Ready-to-Use Grout with Color-Coated Quartz GROUT TROUBLESHO TING GUIDE INSTALLATION SOLUTIONS F OR T I L E A N D STO N E www.na-adhesives.com Grout discoloration A non-uniform,
More informationAtelier Mediums. They are set out in a progression from a thick heavy bodied gel through to a very liquid medium.
Atelier There are several top quality brands of artist acrylic on the world market, but Atelier Interactive is the only brand that can be used in a Fast Drying Mode and in a Wet Blending Mode. There are
More informationCleaning & Maintenance Advice Textured Glass.
Cleaning & Maintenance Advice Textured Glass. Viridian ScalaTexture Viridian ScalaMirage Viridian ScalaDesign Viridian LuminaMist Cleaning of Glass This information is offered as general information only.
More information1. Storage and transportation. Care Instruction
This is to explain proper ways to apply REFLOMAX GLODIAN EGP, HIP and SG films to traffic signs and safety signs at construction site, etc. Even though it is impossible to explain all aspects that need
More informationAdhesive Selection. 1/32 x 1/16 x 1/32 U-notch 4 Gallon 880-1,040 SF 40.0 P u u u. 1/32 x 1/16 x 1/32 U-notch 4 Gallon 1,200-1,400 SF 40.
Sheet Flooring Installation Guide TOLI MATURE SELECT & TAKIRON WELS SHEET CBC Flooring Please refer to the CBC Flooring website www.cbcflooring.com for the most current guidance about product application
More informationWallgard 1,3 product
INSTALLATION INSTRUCTIONS Wallgard 1,3 product October 2015 GENERAL Application can be done to smooth, dry, clean, sound walls of concrete, plaster, hardboard, plywood and fibreboard. Board material must
More information3M Scotchgard Surface Protection Film 2200
Effective July 2016 Commercial Solutions Division 3M Scotchgard Surface Protection Film 2200 Product Bulletin / Instruction Bulletin Product Description 3M Scotchgard Surface Protection Film 2200 is a
More informationRAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION
Suitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection. Easy to apply Excellent anti-corrosion resistance Can be applied
More informationHandrail H Series. Product Installation. Instructions. Installation Instructions For. Wall Mounted and Freestanding Round Handrails
Product Installation Installation Instructions For Instructions Handrail H Series Installation Instructions for Wall Mounted and Freestanding Round Handrails Step Nosing F Series Concrete and Timber Step
More informationAPPLICATION NOTE - SR001. Cold Weather Application
APPLICATION NOTE - SR001 Cold Weather Application Silent Running is best applied with the ambient, material and substrate temperature in the range of 65-85 degrees F. Lower temperatures will result in
More informationSPECIFICATION FOR. BRANZ Appraisal Certificate # 621 (2008)
SPECIFICATION FOR TEKTON WEATHERIZATION SYSTEM BRANZ Appraisal Certificate # 621 (2008) MW TWS 10/07/2012 Page 1 SYSTEM DESCRIPTION The Tekton Weatherization System consists of TEKTON Wall Underlay, Tekton
More informationKnowledge Requirements. Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator. trainthepainter.
Knowledge Requirements Protective Coatings Applicator Abrasive Blast Cleaning Operator Spray Painting Operator trainthepainter.com Knowledge Requirements The Knowledge Requirements the protective coatings
More informationVENEERING AND LAMINATING SOLUTIONS
With over 35 years experience in the adhesives industry, Alansons have become known as a solutions provider, rather than a mere supplier of adhesive products. Nowhere is this fact better demonstrated than
More information3M Air and Vapour Barrier 3015 Technical guide
3M Air and Vapour Barrier 3015 Technical guide Product overview Typical physical properties For installation ease and flexibility, 3M Air and Vapour Barrier 3015 High performance 3M acrylic adhesive grabs
More informationEZYSTONE WORKSURFACES
EZYSTONE WORKSURFACES Installation & Maintenance Instructions 1. Tools Required Worktop Edge Finishing Kit Pack 1-100mm Velcro Backing Pad Pack 2-100mm Diamond Dry Cut Velcro Discs (100 Grit Yellow) (200
More informationPremium quality tools are important; not only will high quality rollers, brushes, and products create a better result, they ll make your job easier.
How to Paint your Pool Introduction Painting is one of the best ways to protect and beautify your pool. In addition to adding a vibrant, fresh color, a new coat of paint can be a cost- efficient way to
More informationData Sheet 5741 Englisch
Data Sheet 5741 Englisch 2K-PUR-Acryl Silk Gloss 2K-PUR-Acryl Seidenglanzlack 5741 two-component, high mechanical resistance, for exterior and interior use, with 2K-PUR-Acryl Hardener 5770 2K-PUR-Acryl
More informationGeneral Installation Instructions
General Installation Instructions Good web sites to check out that may assist you are: For gluing engineered boards over timber chipboard/particle board/ yellow tongue: https://www.youtube.com/watch?v=bpyfr373tl8
More informationSign Maintenance. Sign Maintenance
When does it start? Maintenance should start before the ordered signs arrive. An area should be set aside for the storage of stock and replacement signs. Area should include racks where signs can be stacked
More informationStarQuartz Quartz-Lock Revolutionary Grout Technology
StarQuartz Quartz-Lock Revolutionary Grout Technology Product Description StarQuartz, QuartzLock Grout is a PRE-MIXED, READY-TO-USE URETHANE and colored quartz-based grout for ceramic, porcelain, glass
More informationTECHNICAL DATA SHEET PlastiRoute RP-2C All Colours
Product Description Application Application Equipment is a paste-like, solvent-free road marking cold plastic which cures by addition of peroxide initiator. It is recommended as permanent marking for very
More informationCHEMICAL RESISTANT EPOXY
CHEMICAL RESISTANT EPOXY DATE - 19 DECEMBRER 2016 TECHNICAL DATA SHEET DESCRIPTION is a solvent-less, two component epoxy coating system. It exhibits very good appearance and chemical and physical properties.
More informationCrackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow.
PRODUCT DESCRIPTION Crackle Paste is a water-based product formulated with styrene-acrylic copolymer emulsions, and may have a tendency to yellow. This product has white, low-density solids that replace
More informationSAFETY DATA SHEET VILLAS BITUMEN
Villas Austria GmbH Industriestraße 18 A9586 Fürnitz Tel.: +43 / 4257 / 22410 Fax: +43 / 4257 / 22412390 office@villas.at www.villas.at SAFETY DATA SHEET VILLAS BITUMEN Edition: 25.08.2011 Villas Bitumen
More informationData Sheet K-Aqua Silk Matt Enamel K-Aqua Seidenmattlack K-Aqua Hardener Properties. Material description.
0 Enamel 2388 2K-Aqua Seidenmattlack 2388 Englisch water-based, two-component, highly resistant to mechanical and chemical stress, AgBB certified, for interior and exterior use, with 2K-Aqua Hardener 2380
More informationFOTECAP TOPAZ (4100 Series) Diazo standard capillary film
FOTECAP TOPAZ (4100 Series) Diazo standard capillary film 1. Description TOPAZ is available with dry film thicknesses of 18 μm (4118), 22 μm (4122), 25 μm (4125), 29 μm (4128), 37 μm (4135) and 52 μm (4150)
More informationAtelier Mediums. NEW Atelier Mediums. New! Heavy Gel (Satin)
Atelier There are several top quality brands of artist acrylic on the world market, but Atelier Interactive is the only brand that can be used in a Fast Drying Mode and in a Wet Blending Mode. There are
More informationAQUAGARD EPDM FLAT ROOFING SYSTEMS INSTALLATION GUIDE THE MECHANICALLY FIXED SYSTEM
AQUAGARD EPDM FLAT ROOFING SYSTEMS INSTALLATION GUIDE THE MECHANICALLY FIXED SYSTEM The following guide covers the technique for the Mechanically Fixed System. This system is best employed when an overlay
More informationIRON MIOX Micaceous iron polish, anticorrosive for iron surfaces with no patchy finish
Converter name Destination Finish at high anticorrosie powerd given by the high micaceous iron oxyd. Suitable also in marine and iindustrial environment. Applicable on iron and steel surfaces as well as
More informationSection 914. JOINT AND WATERPROOFING MATERIALS
914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.
More informationCOMPOSITES LAB MANUAL
COMPOSITES LAB MANUAL Version 1 Lab 3: Surface Preparation, Wet Layup, and Vacuum Bagging The original version of this manual was a one student senior design project written by Katherine White, the Composite
More informationGrafiWrap Vehicle Wrapping
GrafiWrap Vehicle Wrapping What is GrafiWrap? GrafiWrap is the registered trade name for a combination of materials used in the wrapping of a vehicle. The GrafiWrap system is a sandwich made up of a cast
More informationInstallation Instructions Palladium 3D Hi Impact Wall System, Partial Height with Color Matched Caulk Joints
Please read all instructions before installing Palladium 3D Hi Impact Wall System.. Before installation: a. Acclimate rigid sheet, Palladium 3D boards, adhesives and wall substrates to room temperature
More information