Fasteners & Accessories For Commercial Construction
|
|
- Amice Cross
- 6 years ago
- Views:
Transcription
1 Fasteners & Accessories For Commercial Construction
2 Table of Contents Page Structural Performance Fastener Strength and Pullout Values... 2 Carbon Steel Self-Drill Fasteners, No Washer... 3 Structural Steel Self-Drill Fasteners... 4 Carbon Steel Self-Drill Fasteners, bondseal Washer... 5 Cupped Sealer Self-Drill Fastners, EPDM Washer Stainless Steel Self-Drill Fasteners... 6 ZAC Zinc Aluminum Capped Self-Drill Fasteners... 7 MAC Stainless Capped Self-Drill Fasteners... 7 Flex5 Grade 5 Performance Fasteners... 8 Wood to Metal Self-Drill Fasteners... 9 woodgrip Fasteners woodgrip HiLo Fasteners #14 Milled Point Wood Screw...11 evergrip Bi-Metal 300 Series Stainless Fasteners...11 woodgrip 300 Series Stainless Aluminum Panel Fasteners...11 woodmac Wood Screw woodzac HiLo Zinc Aluminum Capped Fastener Clip Fasteners Page Carbon Steel Self-Tapping Type A Fasteners Stainless Steel Self-Tapping Type A Fasteners Carbon Steel Self-Tapping Type B Fasteners Stainless Steel Self-Tapping Type B Fasteners SX - HWH 304SS Bi-Metal Self-Drill Fasteners irius SX 304SS Bi-Metal Self-Drill Fasteners SX TORX 304SS Bi-Metal Self-Drill Fasteners Blind Rivets BULB-TITE Rivets Grommet Fasteners Blind Rivet Tools Pipe Flashing Hannoband BG1 Joint Sealant Tape vistacoat Premium System #12 Dekfast Phillips Head (insulation attachment) #14 Dekfast Phillips Head (insulation attachment) Insulation Stress Plates Zinc Nailins Disclosure Statement Structural Performance Fastener Sizes Fastener Size #8 #9 #10 #12 1/4 #14 #17 Thread Diameter Decimal Equivalent Steel Gauge Sizes* Gauge /8 10 3/16 1/4 1/2 Decimal Equivalent (in.) Decimal Equivalent (mm) *Standard steel thickness used for panels, purlins and girts. Fasteners are designed to withstand a varied range of types of loading. Each panel or structural system has its own specifi c fastener loading requirements. Care must be taken to ensure that the appropriate loading requirements for each application are considered. Utlimate Shear Strength The point at which a fastener fails under a load exerted in offset opposing directions, usually upon the shank of the fastener. Typical structural performance criteria that infl uence fastener design include: Ultimate Tension Strength The point at which a fastener fails under a load exerted in two direct opposite direction Ultimate Pull-out Performance The ability of a fastener s threaded connection to remain intact and resist tensile loads. Ultimate Torsion Strength The point at which a fastener fails under a twisting load exerted on the head during installation in a torsional direction. Self-tapping fasteners require that a pilot hole be drilled prior to installation. The pull-out resistance will be directly related to the pilot hole diameter. Self-drilling fasteners have been developed, and are available, for most steel contruction applications, to a metal thickness of 1/2. This type of fastener is manufactured with its own integral drill point, which is engineered to drill the optimum hole size to facilitate effi cient thread forming in the metal structure, resulting in optimized pullout values. 1
3 Structural Performance, continued Ultimate Pull-over performance The ability of a fastener to resist the pulling of the fastened sheet material over the head of the fastener due to gravity, wind, or other load. SFS intec is proud to be a member of these industry trade associations: The resistance to pull-over failure is related to the strength and diameter of the fastener washer and the strength and thickness of the metal panel. Fastener Strength & Pullout Values Strength Values Diameter and TPI Tensile Strength [lbf] Shear Strength [lbf] Torsional Strength [in-lb] Flex5 Fasteners [1] / / Impax, Impax ZAC, Impax MAC Fasteners [1] [2] 1035 [2] 42 [2] / / Pullout Values (Average lbs. ultimate) Diameter and TPI Point Size Gauge /8" 3/16" 1/4" 5/16" Impax, Impax ZAC, Impax MAC Fasteners [1] [2] 479 [2] 685 [2] 933 [2] / / [3] / / [1] Values listed are from an ISO accredited lab unless otherwise noted. (report # STQA50573R1) [2] Values listed were taken from SFS intec lab test results [3] Fasteners failed in tensile 2
4 Carbon Steel Self-Drill Fasteners Metal to metal applications Buy American Act SD SD3 1/4-14 SD3 Silver Painted Colors ICC-ES Listed Material No. Description Drill Pt. Drill Capacity Material No. Impax HWH 1/4 AF, No Washer Carton Qty. Carton Wt x 1/2 SD x 5/8 SD x 3/4 SD Impax HWH 5/16 AF, No Washer x 5/8 SD x 3/4 w/serration SD x 3/4 SD x 3/4 SD * x 1 SD x 1-1/4 SD x 1-1/2 SD Impax HWH 5/16 AF, No Washer x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD x 2-1/2 SD x 3 SD x 4 SD /4-14 x 7/8 (lap) SD Impax HWH 3/8 AF, No Washer /4-14 x 3/4 SD /4-14 x 1 SD /4-14 x 1-1/4 SD /4-14 x 1-1/2 SD /4-14 x 2 SD /4-14 x 2-1/2 SD /4-14 x 3 SD /4-14 x 4 SD Indicates domestic Indicates E-Zinc plating ICC Evaluation Report ESR Buy American Act - Construction Materials Under Trade Agreements 3
5 Structural Steel Self-Drill Fasteners Metal to metal applications Buy American Act 1 Painted SD5 1/4-20 SD5 Silver Colors ICC-ES Listed Material No. Description Drill Pt. Drill Capacity Material No. Impax HWH 5/16 AF, No Washer Carton Qty. Carton Wt x 7/8 SD x 1-1/4 SD x 1-1/4 SD x 1-1/2 SD x 2 SD Impax HWH 3/8 AF, No Washer /4-20 x 3 SD * /4-20 x 4 SD * /4-20 x 5 SD * /4-20 x 6 SD * /4-20 x 7 SD * /4-20 x 8 SD * 43.5 ICC Evaluation Report ESR-3870 Buy American Act SD5 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal Washer x 7/8 SD x 1-1/4 SD x 1-1/4 SD x 1-1/2 SD x 2 SD Impax HWH 3/8 AF, with bondseal Washer /4-20 x 3 SD * /4-20 x 4 SD * /4-20 x 5 SD * /4-20 x 6 SD * /4-20 x 7 SD * /4-20 x 8 SD * Buy American Act - Construction Materials Under Trade Agreements 4
6 Carbon Steel Self-Drill Fasteners with bondseal Washer Metal to metal applications Buy American Act SD SD3 1/4-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal washer x 5/8 SD x 3/4 SD x 1 SD x 1-1/4 SD * x 1-1/2 SD Impax HWH 5/16 AF, with bondseal Washer x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD x 2-1/2 SD x 3 SD x 4 SD /4-14 x 7/8 (lap) SD Impax HWH 3/8 AF, with bondseal Washer /4-14 x 3/4 SD /4-14 x 1 SD /4-14 x 1-1/4 SD /4-14 x 1-1/2 SD /4-14 x 2 SD /4-14 x 2-1/2 SD /4-14 x 3 SD /4-14 x 4 SD * Buy American Act - Construction Materials Under Trade Agreements 5
7 Cupped Sealer Self-Drill Fasteners Metal to metal applications Buy American Act SD3 Silver Painted Colors ICC-ES Listed Material No. Description Drill Pt. Drill Capacity Material No. Impax Cupped HWH 5/16 AF, with EPDM Sealing Washer Carton Qty. Carton Wt x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD ICC Evaluation Report ESR Stainless Steel Self-Drill Fasteners Metal to metal applications Made in USA SD3 410 SS No Washer SD3 410 SS Aluminum bondseal Washer Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt. 410 Stainless HWH 5/16 AF, No Washer x 3/4 SD x 1 SD x 1-1/4 SD /4-14 x 7/8 (lap) SD Stainless HWH 5/16 AF, with Aluminum bondseal Washer x 3/4 SD * x 1 SD * x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD Buy American Act - Construction Materials Under Trade Agreements 6
8 ZAC - Zinc Aluminum Capped Self-Drill Fasteners Metal to metal applications Buy American Act SD SD5 E-Zinc Plating ICC-ES Listed Material No. Description Drill Pt. Drill Capacity Material No. ZAC Impax HWH 5/16 AF, with EPDM washer Carton Qty. Carton Wt x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD /4-14 x 7/8 (lap) SD /4-14 x 1-1/4 SD ZAC Impax HWH 3/8 AF, with EPDM washer x 1-1/4 SD x 1-1/2 SD ICC Evaluation Report ESR-3870 MAC - Stainless Capped Self-Drill Fasteners Metal to metal applications Buy American Act SD3 Silver Painted Colors ICC-ES Listed Material No. Description Drill Pt. Drill Capacity Material No. MAC Impax Stainless Capped HWH 5/16 AF, with EPDM Washer Carton Qty. Carton Wt x 1 SD x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD ICC Evaluation Report ESR Buy American Act - Construction Materials Under Trade Agreements 7
9 Flex5 Selectively Hardened Fasteners with Grade 5 Performance Made in USA ICC-ES Listed Material No. Description Drill Pt. Material No. Flex Self-Drill; HWH 5/16" AF Drill & Tap Capacity Load Bearing Area Carton Qty. Carton Wt x 3/4 SD * x 7/8 SD * x 1 SD * x 1-1/2 SD * x 2 SD * 16 Flex Self-Drill; PUF (Phillips Undercut Flat) X 1 SD * 36 Flex Self-Drill; HWH 5/16" AF x 1-3/4 SD * 36 Flex5 1/4-14 and 1/4-20 Self-Drill; HWH 3/8" AF /4-14 x 1 SD * /4-14 x 1-1/2 SD * /4-14 x 2 SD * /4-20 x 1-1/8 SD * /4-20 x 1-1/2 SD * /4-20 x 2 SD * /4-20 x 2-1/2 SD * 19 Flex5 self-drilling fasteners are made from alloy steel and are fi nished with a selective hardness heat treatment process to give the load bearing part of the fastener Grade 5 specifi cations (RC 28-34), with a higher hardness for the drill point and lead-in threads (min. RC 52). Finish: vistacorr TM Technical Data SD3 Flex5 1/4-14 SD3 Flex5 Flex5 Head Marking Grade 5 head and threads (RC 28-34) Ideal for curtainwall, architectural cladding, rainscreen and dissimilar metal applications when used with aluminum. Higher-hardness lead threads and point (min. RC 52) ICC Evaluation Report ESR-3870 Flex5 Fasteners [1] Pullout Test Results - Steel Dia. & TPI Point Type Drill Cap. Panel Thickness /8" 3/16" 1/4" 5/16" [3] / / [3] Flex5 Fasteners [1] Shear Test Results - Steel Dia. & TPI Point Type Drill Cap. Panel Thickness (Contact with head - Contact with threads) /4"-3/16' [4] [4] [4] [4] 2504 [4] 1/ [4] - 1/ [4] 2735 [4] Pullout Test Results - Aluminum Dia. & TPI Point Type Drill Cap. Panel Thickness 1/8 1/4 3/ / / Shear Test Results - Aluminum Panel Thickness Dia. & TPI Point Type Drill Cap. 1/8-1/8 1/8-1/ / / [1] Values listed are from an ISO accredited lab unless otherwise noted. (report # STQA50573R1) [3] Fasteners failed in tensile [4] Fasteners failed in shear 8
10 Wood to Metal Self-Drilling Fasteners For attaching wood to steel Buy American Act 1 1/4-20 SD4 Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Ply Metal Self-Drill with Wings; Wafer Head, #2 Phillips Drive x 1-7/16 SD /4 Plywood Header Self-Drill with Wings; Flat Head, #3 Phillips Drive x 2 SD up to x 2-1/2 SD up to 1-1/ Header Self-Drill with Wings; Flat Head, #3 Phillips Drive /4-20 x 2-3/4 SD Steel up to 1-3/4 Wood Brown Vista coating for corrosion resistance Suitable for pressure treated wood Exceeds 1,000 hours salt spray testing Wings designed to ream a hole to prevent "wood jacking" Excellent for wood or header attachments to steel Meets ASTM C1513 for cold-formed steel frame connections 1 Buy American Act - Construction Materials Under Trade Agreements 9
11 woodgrip TM Fasteners Metal to wood applications 9-15 woodgrip Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HWH 1/4 AF, with controlseal washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) x 3 Sharp Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga Silver Color woodgrip TM HiLo Wood Screw Metal to wood applications woodgrip HiLo Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HiLo, HWH 1/4 AF, with bondseal Washer x 1 Type 17 Pt. 24 ga (.024) x 1-1/2 Type 17 Pt. 24 ga (.024) x 2 Type 17 Pt. 24 ga (.024) x 2-1/2 Type 17 Pt. 24 ga (.024) x 3 Type 17 Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga
12 #14 Milled Point Wood Screw Metal to wood applications #14 Type 17-A MP Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. #14 Wood Fastener, HWH 5/16 AF. Type 17-A Milled, with bondseal Washer x 1 Type 17-A MP x 1-1/2 Type 17-A MP x 2 Type 17-A MP x 2-1/2 Type 17-A MP x 3 Type 17-A MP evergrip Bi-Metal 300 Series Stainless Fasteners Metal to wood applications 9-15 evergrip Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. evergrip Bi-Metal Stainless HWH 1/4 AF, with Stainless bondseal Washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) woodgrip 300 Series Stainless Aluminum Panel Fasteners Aluminum panel applications Painted Colors SS woodgrip Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt Series Stainless Aluminimum Panel woodgrip, 1/4 HWH, Aluminum bondseal Washer x 1 Sharp Pt..032 Alum. Max x 1-1/2 Sharp Pt..032 Alum. Max x 2 Sharp Pt..032 Alum. Max x 2-1/2 Sharp Pt..032 Alum. Max x 3 Sharp Pt..032 Alum. Max
13 woodmac TM Wood Screw Metal to wood applications 9-15 woodmac E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodmac 1/4 Stainless Capped HWH with EPDM Washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga woodzac TM HiLo Zinc Aluminum Capped Fasteners Metal to wood applications woodzac HiLo E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodzac HiLo, 5/16 AF Zinc Alloy Capped, with Aluminum bondseal Washer x 1 Type 17 Mill Pt. 24 ga (.024) x 1-1/2 Type 17 Mill Pt. 24 ga (.024) x 2 Type 17 Mill Pt. 24 ga (.024) x 2-1/2 Type 17 Mill Pt. 24 ga (.024) x 3 Type 17 Mill Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga
14 Clip Fasteners Standing Seam Panel Clip #10 Type A Pancake #12-8 XG Pancake #12-8 XG Low Profi le #12 Type A Pancake #10 SD2 Pancake #12 SD 2 Pancake #12-24 SD5 Pancake E-Zinc Plating Material No. ICC-ES Listed Material No. Description Drive Type Drill Pt. Carton Qty. Carton Wt.. Metal to Wood Application x 1 Pancake 2/2 Square Phillips Type A x 1-1/2 Pancake 2/2 Square Phillips Type A x 2 Pancake 2/2 Square Phillips Type A x 1 XG Pancake 2/2 Square Phillips Sharp Pt x 1-1/2 XG Pancake 2/2 Square Phillips Sharp Pt x 2 XG Pancake 2/2 Square Phillips Sharp Pt x 1 XG Low Profi le 2/2 Square Phillips Sharp Pt x 1-1/2 XG Low Profi le 2/2 Square Phillips Sharp Pt x 2 XG Low Profi le 2/2 Square Phillips Sharp Pt x 1 Pancake 2/2 Square Phillips Type A x SS Pancake #2 Phillips Type A x SS Pancake #2 Phillips Type A Metal to Metal Appplication x 1 Pancake 2/2 Square Phillips SD x 1-1/2 Pancake 2/2 Square Phillips SD x 2 Pancake 2/2 Square Phillips SD x 1 Pancake 2/2 Square Phillips SD x 1-1/2 Pancake 2/2 Square Phillips SD ICC Evaluation Report ESR
15 Carbon Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A - Carbon Steel; 3/8 HH with bondseal x 3/4 Type A Pre-drill required.500" x 1 Type A Pre-drill required.750" x 1-1/4 Type A Pre-drill required 1.000" x 1-1/2 Type A Pre-drill required 1.250" x 2 Type A Pre-drill required 1.750" x 2-1/2 Type A Pre-drill required 2.250" x 3 Type A Pre-drill required 2.750" x 3-1/2 Type A Pre-drill required " 1250* x 4 Type A Pre-drill required " 1000* x 5 Type A Pre-drill required " 750* x 6 Type A Pre-drill required " 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A Stainless Steel; 3/8 HH with Stainless bondseal x 3/4 Type A Pre-drill required.500" x 1 Type A Pre-drill required.750" x 1-1/4 Type A Pre-drill required 1.000" x 1-1/2 Type A Pre-drill required 1.250" x 2 Type A Pre-drill required 1.750" x 2-1/2 Type A Pre-drill required 2.250" x 3 Type A Pre-drill required 2.750" x 3-1/2 Type A Pre-drill required " 1250* x 4 Type A Pre-drill required " 1000* x 5 Type A Pre-drill required " 750* x 6 Type A Pre-drill required " 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. 14
16 Carbon Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size #8 (.199) #7 (.201) #1 (.228) #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Type Drill Capacity Carton Qty. Carton Wt. Self-Tapping - Type B - Carbon Steel; 3/8 HH with bondseal /4-14 x 3/4 Type B Pre-drill required.550" 2500* /4-14 x 1 Type B Pre-drill required.800" 2500* /4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* /4-14 x 2 Type B Pre-drill required 1.800" 2000* /4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* /4-14 x 3 Type B Pre-drill required 2.800" 1500* /4-14 x 3-1/2 Type B Pre-drill required " 1250* /4-14 x 4 Type B Pre-drill required " 1000* /4-14 x 5 Type B Pre-drill required " 750* /4-14 x 6 Type B Pre-drill required " 500* 33.0 Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size #8 (.199) #7 (.201) #1 (.228) #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Self-Tapping - Type B Stainless Steel; 3/8 HH with Stainless bondseal /4-14 x 3/4 Type B Pre-drill required.550" 2500* /4-14 x 1 Type B Pre-drill required.800" 2500* /4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* /4-14 x 2 Type B Pre-drill required 1.800" 1500* /4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* /4-14 x 3 Type B Pre-drill required 2.800" 750* /4-14 x 3-1/2 Type B Pre-drill required " 1250* /4-14 x 4 Type B Pre-drill required " 1000* /4-14 x 5 Type B Pre-drill required " 750* /4-14 x 6 Type B Pre-drill required " 500* 33.0 Part number not set up in SAP. Use description to order. Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. 15
17 SX - HWH 304SS Bi-Metal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 SX3 Stainless bondseal SX5 Stainless bondseal SX14 No Washer Painted Colors Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-1/ x 1-1/ x SX3 Self-Drill No Washer, 5/16 AF HWH x 1-1/ x 1-1/ x SX5 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 3-1/ x 3-3/ SX5 Self-Drill No Washer, 5/16 AF HWH x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 3-1/ x 3-3/ SX14 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-9/ x 1-7/ x 2-1/ x 3-1/ SX14 Self-Drill No Washer, 5/16 AF HWH x 1-9/ x 1-7/ x 2-1/ x 3-1/ SL2 Lap with Stainless bondseal Washer, 5/16 AF HWH x 1 (lap) /4-14 x 1-1/8 (lap) SL2 Lap No Washer x 1 (lap) Buy American Act - Construction Materials Under Trade Agreements 16
18 irius SX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 irius SX3 No Washer irius SX5 Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-L12 irius Self-Drill with Stainless bondseal Washer x 1-1/ x 1-1/ SX3-L12 irius Self-Drill No Washer x 1-1/ x 1-1/ x 1-1/ SX5-L12 irius Self-Drill with Stainless bondseal Washer x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 2-7/ SX5-L12 irius Self-Drill No Washer x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 2-7/ SX14-L12 irius Self-Drill with Stainless bondseal Washer x 1-9/ SX14-L12 iirius Self-Drill No Washer x 1-9/ SL2-L12 irius Self-Drill with 14mm SS bondseal Washer /4-14 x 1 (lap) SL2-L12 irius Self-Drill with 16mm SS bondseal Washer /4-14 x 1 (lap) Painted Colors Installation: The E420 irius drive socket (#973316) is required. 1 Buy American Act - Construction Materials Under Trade Agreements 17
19 SX - TORX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Rainscreen cladding Facade Panel (HPL, fiber cement) Buy American Act 1 Painted Colors SX5 TORX No Washer SX5 TORX Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-D10 TORX No Washer (T20W) x SX3-D12 TORX No Washer (T25) x 1-3/ x 2-1/ SX5-D12 TORX with Aluminum bondseal Washer (T25) x 1-1/ SX5-D12 TORX No Washer (T25) x 1-1/ SL2-S-D12 TORX with Aluminum bondseal Washer (T20W) x 1-1/16 (lap) SL2-S-D12 TORX No Washer (T20W) x 1-1/16 (lap) Blind Rivets Blind rivet attach light gauge Made in USA Call customer service for painted color rivet options Material No. Description US Dimens. Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. All Aluminum Rivet - Dome Head / Rivet Diameter - 1/ AA42D Rivet #30 ( ) AA43D Rivet #30 ( ) AA44D Rivet #30 ( ) All Stainless Rivet - Dome Head / Rivet Diameter - 1/ STST43D Rivet #30 ( ) STST44D Rivet #30 ( ) STST46D Rivet #30 ( ) Buy American Act - Construction Materials Under Trade Agreements 18
20 BULB-TITE Rivets s for up to grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Dome Head Protruding Crown - With Washer RV W 5/ #20 ( ) 3500* RV W 5/ #20 ( ) 3500* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 2000* RV W 3/ #4 ( ) 2000* RV W 3/ #4 ( ) 1500* RV W 3/ #4 ( ) 1500* RV W 3/ #4 ( ) 1500* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 1500* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* 3.0 Aluminum/Aluminum Dome Head Protruding Crown - No Washer RV / #20 ( ) 3500* RV / #20 ( ) 3500* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 2000* RV / #4 ( ) 2000* RV / #4 ( ) 1500* RV / #4 ( ) 1500* RV / #4 ( ) 1500* RV / /4 ( ) 2000* RV / /4 ( ) 2000* RV / /4 ( ) 2000* RV / /4 ( ) 1500* RV / /16 ( ) 1000* RV / /16 ( ) 1000* RV / /16 ( ) 1000*
21 BULB-TITE Rivets, continued s for up to grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Large Flange Protruding Crown - With Washer RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* 7.0 Aluminum/Aluminum Large Flange Protruding Crown - No Washer RV / /16 ( ) 1000* RV / /16 ( ) 1000* RV / /16 ( ) 1000* 7.0 Grommet Fastener Attach fi berglass panels Made in USA Material No. Description Head Style Washer Carton Qty. Carton Wt.. Stainless Grommet / Stainless bondseal x 7/8 5/16 AF Hex 15 mm O.D. 3000* x 1-1/4 1/4 AF Hex 12 mm O.D. 2500*
22 Blind Rivet Tools Installation tools for blind rivets PowerBird Pro Gold Series (Recommended for BULB-TITE rivets) 18 Volt Brushless & Cordless Riveting Tool Buy American Act 1 Material Number: Weight: 4.4 lbs Power Pack: 18.0 Volt, rechargeable Li-Ion / 2.1 Ah Battery Charger: V/50-60Hz, minute charge time Note: 9/32 diameter BULB-TITE will require Nose tip AccuBird Pro 18 Volt Brushless & Cordless Riveting Tool Material Number: Weight: 4.4 lbs Power Pack: 18.0 Volt, rechargeable Li-Ion / 2.1 Ah Battery Charger: V/50-60Hz, minute charge time Battery : Volt, 2.1 Ah Li-Ion Battery AccuBird 14.4 Volt Cordless Riveting Tool Material Number: Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah Battery Charger: 110V/60Hz, 60 minute charge time PowerBird (Recommended for BULB-TITE rivets) 14.4 Volt Cordless Riveting Tool Material Number: Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah Battery Charger: 110V/60Hz, 60 minute charge time Note: 9/32 diameter BULB-TITE will require Nose tip and shorter jaws required. Batteries: Volt, 1.3 Ah Li-Ion Battery Volt, 2.6 Ah Li-Ion Battery 1 Buy American Act - Construction Materials Under Trade Agreements 21
23 Pipe Flashing Square and round base pipe roof pipe flashing Material No. Black EPDM Material No. Gray EPDM Material No. Red Silicone Flasher Size Pipe Diameter Carton Qty. Carton Wt.. Square Base Pipe Flashing #1 1/4 to 2-3/ #2 7/8 to #3 1/4 to 5-3/ #4 2-3/4 to #5 4 to 8-1/ #6 4-3/4 to #7 5-1/2 to #8 6-3/4 to 13-1/ #9 9-1/2 to 20-1/ #10 12 to 28-1/ Retrofit Square Base Pipe Flashing #1 1/2 to #2 4 to 9-1/ #3 9-1/4 to 16-1/ Round Base Pipe Flashing #1 1/4 to 2-1/ #2 1-3/4 to #3 1/4 to #4 3 to 6-1/ #5 4-1/2 to 7-3/ #6 5 to #7 6 to #8 7 to #9 9 to Retrofit Round Base Zipper Pipe Flashing #1 3/4 to 2-3/ #2 2 to 7-1/ #3 3-1/4 to Part number not set up in SAP. Use description to order. Made in USA 22
24 Use for sealing joints and seams in metal panels, gaps around door and window frames, and expansion joints in buildings Pre-compressed, self-expanding polyurethane foam Acrylate dispersion impregnation Resistant to rain, wind, sun/uv, sound, draft and dust Pressure sensitive adhesive for fast and easy installation Flame retardant Hannoband BG1 Joint Sealant Tape Material No. Size Thickness x Width Expanded 100% Performance Fully Expanded Uncompressed Thickness Length/Roll Packaging /4 x 1 1/4 1 x ft. 12 rolls/ctn /8 x 1 3/8 1-1/2 x ft. 12 rolls/ctn 8.0 Ctn. Wt. Application vistacoat Premium System High Performance Color Finish SFS intec developed the vistacoat Premium System fi nish for panel attachment fasteners. Utilizing new coating and processing technology, the fi nish has improved appearance, corrosion resistance, durability and installation performance. The fi nish system consists of: pre-treatment seal coat color top coat - contact SFS intec for color matches zinc plating primer coat Silver vistacoat is standard. Performance Corrosion Resistance - on all plain and color product Kesternich per DIN liter - 15 cycles Salt Spray per ASTM B117 1,000 hrs. Consistent Durability Adhesion Impact resistance Appearance gloss and color; application processes ensure consistent results UV Resistance New superior UV-resistant pigmentation Results exceed previous market offerings in gloss retention and color stability 23
25 #12 Dekfast Phillips Head For insulation attachment For attachment to: Steel roof decks Wood roof decks E-Coat Plating Application / Thickness Material No. Description Steel Wood Concrete Carton Qty. Carton Wt.. #12 Dekfast, #3 Phillips drive, 13 tpi, drill point x 1-5/8" Up to 7/8" Up to 5/8" N/A 1000* x 2-1/4" 5/8" to 1-1/2" Up to 1-1/4" N/A 1000* x 2-7/8" 5/8" to 2-1/8" Up to 1-1/8" N/A 1000* x 3-1/4" 1/2" to 2-1/2" 1/2" to 2-1/4" N/A 1000* x 3-3/4" 1" to 3" 1" to 2-3/4" N/A 1000* x 4-1/2" 3/4" to 3-3/4" 3/4" to 3-1/2" N/A 1000* x 5" 1-1/4" to 4-1/2" 1-1/4" to 4" N/A 1000* x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" N/A 1000* x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" N/A 500* x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" N/A 500* 28 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #12 fasteners meet Factory Mutual corrosion-resistance Standard Installation Tools: rpm screw guns with hardened #3 Phillips bit. The standard carton package includes one #3 Phillips bit. 24
26 #14 Dekfast Phillips Head For insulation and membrane attachment For attachment to: Steel roof decks Wood roof decks Structural concrete roof decks E-Coat Plating Material No. Description Application / Thickness Steel Wood Concrete Carton Qty. Carton Wt.. #14 Dekfast, #3 Phillips drive, 10 tpi, drill point x 1-1/4" Up to 1/2" Up to 1/4" Up to 1/4" 1000* x 2" Up to 1-1/4" Up to 1-1/4" Up to 1" 1000* x 3" Up to 2-1/4" Up to 2" Up to 2" 1000* x 4" 1-1/4" to 3-1/4" 1-1/4" to 3" 2" to 3" 1000* x 5" 1-1/4" to 4-1/4" 1-1/4" to 4" 3" to 4" 1000* x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" 4" to 5" 1000* x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" 5" to 6" 500* x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" 6" to 7" 500* x 9" 5-1/4" to 8-1/4" 5-1/4" to 8" 7" to 8" 500* x 10" 6-1/4" to 9-1/4" 6-1/4" to 9" 8" to 9" 500* x 11" 7-1/4" to 10-1/4" 7-1/4" to 10" 9" to 10" 500* x 12" 8-1/4" to 11-1/4" 8-1/4" to 11" 10" to 11" 500* 45 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board and/or roof cover to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #14 fasteners meet Factory Mutual corrosionresistance Standard Installation Tools: rpm screw guns with hardened #3 Phillips bit. For structural concrete, 3/16" carbide bit and 1500 rpm max screw guns, or hammerdrills in the hammer mode. Structural concrete to be pre-drilled to minimum 1/2" deeper than fastener penetration. The standard carton package includes one #3 Phillips bit. Insulation Stress Plates For insulation attachment Use with: #12 Dekfast fasteners #14 Dekfast fasteners Made in USA AZ50 Galvalume Material No. Description Outside Diameter Inside Diameter Carton Qty. Carton Wt.. Insulation Stress Plates Galvalume Steel Hex Insulation Plate 2-7/8" Hex.270" 1000* Galvalume Steel 3" Round Insulation Plate 3" Round.260" 1000*
27 Zinc Nailins For fastening termination bar at wall terminations For attachment to: Concrete Block Brick Stone Material No. Diameter & Length Carton Qty. Carton Wt.. Zinc Nailin, Mushroom Head, Zamac 7 Body /16 x 7/8" 500* /4 x 3/4" /4 x 1" 500* /4 x 1-1/4" 500* /4 x 1-1/2" 500* /4 x 2" 500* 16 * inner boxes of 100 pc./box Performance Load Capacities (4000 psi concrete) Diameter 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" Embed. Depth 3/4" 5/8" 7/8" 1-1/8" 1-3/8" 1-7/8" Tension Load (lbs) Shear Load (lbs) Notes: Load capacity is related to embedment depth. Select anchor length to provide needed embedment depth for the installed anchor. The 1-1/4" length is popular for 1/8" composite thickness applications resulting in 1-1/8" embedment. All load values listed are ultimate load capacities and are not allowable load capacities. These loads should be reduced by an appropriate safety factor of at least 4 to determine the allowable load. Installation Tools: Carbide-tipped masonry drill bit sized slightly larger than nominal diameter to allow clearance. A 3/16" nominal masonry drill bit is actually.198"-.206" diameter. A 1/4" nominal size is actually.260"-.268" diameter. Procedure: Position the fixture and drill a hole the same diameter as the zinc nailin (3/16" or 1/4"). Insert the anchor and tap gently against the fi xture to be fastened. Drive the nail fl ush to the anchor head to expand the anchor. Disclosure Statement Fastener data shown herein is subject to change or correction for typographical error without notice. All test data and ultimate values shown in the catalog are the result of laboratory testing. Specifi c job conditions should be considered and appropriate safety factors applied when specifying fasteners. In actual applications, proper installation techniques must be used to assure adequate performance of the fastener. Final selection of fasteners or accessories for use is ultimately the decision of the purchaser. While SFS intec, Inc. may assist by providing data and information for comparison, SFS intec makes no suggestions or warranties pertaining to the suitability of its products for any particular application. TORX is a registered trademark of Textron Inc. Hannoband is a registered trademark of Hanno Werk GmbH & Co. KG. 1 Buy American Act - Construction Materials Under Trade Agreements 26
28 epost esolutions - Supply Chain innovations are just a click away eportal eshop Job Pack VMI EDI escan Our Technologies Provide easier, faster & more secure working methods n Reduce supply chain costs n Minimize errors n Improve information availability n epullout eformat Visit our website, or contact us to learn more Manufacturing Locations Exeter Plant Lincoln Corporate Center, 41 Dennis Drive, Reading, PA Medina Plant 5201 Portside Drive, Medina, OH Wyomissing Plant 1045 Spring Street, PO Box 6326, Wyomissing, PA Canada Plant 40 Innovation Drive, Dundas, ON L9H 7P3 US Service Centers: Contact Us Toll Free: Toll-free Fax: Northeast: 1045 Spring Street, PO Box 6326, Wyomissing, PA T: Northern Midwest: 500 West 3rd Avenue, Durant, IA T: Toll-free Fax: Southeast: 675 Progress Center Ave., Unit M, Lawrenceville, GA West Coast: 2426 Port Street, West Sacramento, CA F: T: F: T: Toll-free Fax: F: Canada Service Center: Contact Us Toll-Free : Toll-free Fax: Innovation Drive, Dundas, ON L9H 7P3 T: SFS Intec / Printed in USA Technical advice and sales service SFS intec Division Construction T Spring Street F PO Box 6326 us.construction@sfsintec.biz US-Wyomissing, PA F: F: Technical Changes Reserved May 2017 SFS intec - Canada 40 Innovation Drive Dundas, ON L9H 7P3 T ca.info@sfsintec.biz
Fasteners & Accessories For Commercial Construction
Fasteners & Accessories For Commercial Construction Table of Contents Page Structural Performance... 1-2 Fastener Strength and Pullout Values... 2 Carbon Steel Self-Drill Fasteners, No Washer... 3 Structural
More informationFastener Design. Fastener Materials. Coated Corrosion-Resistant Fasteners. Metal Alloy Capped Fasteners
Threaded fasteners for roofing and siding systems are available in a wide range of materials, designs, and coatings. When specifying your fastener, be sure to choose one that has a performance life equaling
More informationREPORT HOLDER: SFS INTEC 1045 SPRING STREET WYOMISSING, PENNSYLVANIA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3870 Reissued 01/2018 This report is subject to renewal 01/2019. DIVISION: 05 00
More informationRoofing and Cladding Product Guide
Product Guide Table of Contents Section Page Section Page General Information Fastener Design... 3-4 Washer Styles, Fastener Head Styles & Internal Drive Types... 5 Structural Performance... 6 Proper
More informationMETAL-TO-WOOD FASTENERS QUIKGRIP METAL2WOOD METAL2WOOD HD METAL2WOOD XD LOPRO 300SS. Value through the Roof.
METAL-TO-WOOD FASTENERS QUIKGRIP METAL2WOOD METAL2WOOD HD METAL2WOOD XD LOPRO 300SS Value through the Roof. Proven Performance. Huge Selection. Marco Quality. Value drives everything we do. That s why
More informationMETAL-TO-METAL FASTENERS QUIKDRILL METAL2METAL METAL2METAL HD. Value through the Roof.
METAL-TO-METAL FASTENERS QUIKDRILL METAL2METAL METAL2METAL HD Value through the Roof. Reliable Self-Drilling Performance. Superior Marco Value. Value drives everything we do. That s why our exclusive Weather-Tite
More informationFASTENERS QUIKDRILL QUIKGRIP CLIPSCREWS. Value through the Roof.
FASTENERS QUIKDRILL QUIKGRIP CLIPSCREWS Value through the Roof. METAL-TO-METAL FASTENERS for CANADA QUIKDRILL METAL2METAL Value through the Roof. Reliable Self-Drilling Performance. Superior Marco Value.
More informationSheet Steel Facts. Most common head design for self-drilling, self-tapping screws.
Sheet Steel Facts Fastener Guide for Sheet Steel Building Products August, 2003 Fastener Materials Fasteners are manufactured from several materials and coatings. For the purpose of this fact sheet, the
More informationUltraCon Masonry Fasteners High Performance in a Wide Range of Applications
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications The UltraCon masonry fastening system from Elco Construction Products offers optimal performance in a wide range of masonry applications.
More informationLow Slope Fastening Solutions Guide
Low Slope Fastening Solutions Guide Featuring Products & Systems Table of Contents Section Page General Information Dekfast Identification Convention...2 Fasteners #12 Phillips Head...3 #12 Hex Head...4
More informationUltraCon Masonry Fasteners High Performance in a Wide Range of Applications
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications The UltraCon masonry fastening system from Elco Construction Products offers optimal performance in a wide range of masonry applications.
More informationUltraCon Masonry Fasteners High Performance in a Wide Range of Applications
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications The UltraCon masonry fastening system from Elco Construction Products offers optimal performance in a wide range of masonry applications.
More informationScrew selecting guide for Norex & Noroc panels installation (metal screw)
Screw selecting guide for Norex & Noroc panels installation (metal screw) Anchor Capacity (lbs.) (1)()() Girt thickness (2) Panel type NOREX Mfg. 2 x TEKS ( 1) 2 x TEKS ( 28) 2 x IMPAX SD ( 1) 2 x IMPAX
More informationDEKFAST COMMERCIAL ROOFING FASTENERS
STEEL DECKING & UL DECKING ATTACHMENT FASTENERS Used for attachment of steel decking attachment to 12ga up to 1/2 thick steel purlin structures. #10 x 3/4 designed for steel B deck side lap stitch. The
More informationBUILDING FASTENERS METAL TO WOOD FASTENERS
BUILDING FASTENERS METAL TO WOOD FASTENERS PAINT + TESTING PaintingOptions MATCHTECH The world s best fasteners now in any color, any time. MatchTech is Marco Industries stateofthe art, high quality polyurethane
More informationUL Construction No. 254
UL Construction No. Wind-Uplift - Class 90 (See Item No. ) / Fire Not Investigated Metal Roof Deck Panels* Snap-Clad No. MSG or No. MSG min. thickness coated steel panels. Panels in. wide max., 0 in. wide
More informationCIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD METAL SCREWS. 6 x 3/4 P/N x 1 METAL SCREW P/N x 3/4 METAL SCREW
A21-1 1160 CIC 200 PLASTIC SCREW ANCHOR ASSORTMENT WITH PHILLIPS BINDING HEAD S For light duty applications in solid materials Color coded diameters for easy identifi cation Acid resistant NYLON FLANGED:
More informationPerlok CR 1.2 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum
Perlok CR 1.2 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum u Uses THE PERLOK CR 1.2 BASE SHEET FASTENER is a one piece unit, precision formed from G-90 galvanized
More informationLarge Diameter Tapcon
CONCRETE ANCHORING SPECIALISTS Large Diameter Tapcon (LDT ) Anchors Finished head, Removable Anchor DESCRIPTION/SUGGESTED SPECIFICATIONS Self-threading Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE The
More informationSCREW FASTENER SELECTION FOR COLD-FORMED STEEL FRAME CONSTRUCTION
test TECHNICAL NOTE On Cold-Formed Steel Construction $5.00 Cold-Formed Steel Engineers Institute Washington, DC www.cfsei.org 866-465-4732 SCREW FASTENER SELECTION FOR COLD-FORMED STEEL FRAME CONSTRUCTION
More informationNotes B
Notes B 2 TABLE OF CONTENTS TEKS Fastener Features...B 4 TEKS Self Drilling Fasteners...B 5 Light Duty Steel-To-Steel Applications...B 6 Medium Duty Steel-To-Steel Applications...B 8 Heavy Duty Steel-To-Steel
More informationFasteners Engineered for Cutting Edge Performance
?I Fasteners Engineered for Cutting Edge Performance 6357 Reynolds Road, Tyler, Texas 75708 P.O. Box 4515, Tyler, Texas 75712 800-352-4864 800-352-3940 Fax 903-592-2826 903-592-1583 Fax 9950 Princeton
More informationSpecialty Fastening Systems Solutions for the Construction Industry
Specialty Fastening Systems Solutions for the Construction Industry BI-METAL SCREWS Drywall / Denseglass SELF DRILLING SCREWS IN STAINLESS STEEL SUS304 Steel Framing Exterior Sheathing Plank / Panel Sidings
More informationGrade 5 dual-hardened concrete/masonry screw anchoring system
Innovative Fastening Technology NEW! #14 Diameter Grade 5 dual-hardened concrete/masonry screw anchoring system Virtually immune to embrittlement failure! 1 The #14 Conflex has a more robust cross-sectional
More informationPerlok CR 1.2 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum
Perlok CR 1.2 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum u THE PERLOK CR 1.2 BASE SHEET FASTENER is a one piece unit, precision formed from G-90 galvanized steel,
More informationPOWER-Skru Large Diameter Concrete Screw
POWER-Skru Large Diameter Concrete Screw Description The POWER-Skru Large Diameter Concrete Screw is a highstrength screw anchor with self-tapping threads that offer a unique undercutting design for anchoring
More informationStainless Steel Anchors. for Concrete & Masonry
Innovative Fastening Technologies Stainless Steel s for Concrete & Masonry The Industry Leader in Critical Fastening Stainless Steel s for Concrete and Masonry Applications To meet the needs of the wide
More information4isofast Product code Page
Fasteners, stress plates and plastic sleeves isofast Product code Page Carbon steel DT.3 Austenitic stainless steel S.6 Carbon steel TI.11 Drill bits SDS.13 isotak Product code Page Carbon steel Austenitic
More informationPeco Fasteners 3/8 Internal Plug Drop In 50 Per Jar 3/8-16 SMART DROP IN ANCHOR ZINC
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-794 Fax: 936-560-4685 Catalog Number Manufacturer Description Weight per unit Product Category 6337J 3/8-6 Smart Drop In Zinc Peco Fasteners,
More informationPRODUCT INFORMATION. ASTM B633,SC1, Type III (Fe/Zn 5) Rod/Anchor Diameter
PRODUCT INFORMATION Internally Threaded Expansion Anchor PRODUCT DESCRIPTION The is an all-steel, machine bolt anchor available in carbon steel. It can be used in solid concrete, hard stone, and solid
More informationElco Construction Products 1301 Kerr Drive Decorah, IA fax:
Technical Manual 2010 HangerMate anchors were designed to speed installation of fire sprinkler, HVAC, refrigeration, general piping, and electrical systems. They can also be used to install strut channels,
More informationFor. Metal Roofing. Cement Roofing. Metal Framing & Fixing. Concrete Fixing
Metal To Metal Fixing Calcium Silicate Boards Metal To wood Fasteners For Concrete Metal Roofing & Cladding For Metal Roofing Fixing AHU & Ventilators Doors & Window Framing Cement Roofing Metal Framing
More informationROSKO FASTENERS & SUPPLY, INC FASTENERS FOR CONSTRUCTION
406 Bell Court Woodstock, GA 30188 www.roskofasteners.com A Customer-Conscious Company OUR MISSION At Rosko Fasteners & Supply we are committed to the profitability of our customers. We consider our customers
More informationZXL MB Advantage Catalog. A Division of The Hillman Group
ZXL MB Advantage 2019 Catalog A Division of The Hillman Group?I ST Advantage...Value Added Innovation 6357 Reynolds Road, Tyler, Texas 75708 P.O. Box 4515, Tyler, Texas 75712 800-352-4864 800-352-3940
More informationANCHORS SLEEVE ANCHORS BOLT DIAMETER
SLEEVE ANCHORS No hole spotting. No mis-alignments. Simply drill through the fixture into concrete, insert and tighten. Preassembled for fast, easy installation. No special tools necessary; meets federal
More informationREPORT HOLDER: INTERCORP DBA OF U.S. NITTO 641 NORTH POPLAR ORANGE, CALIFORNIA EVALUATION SUBJECT: STRONG POINT SCREWS
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3528 Reissued 07/2017 This report is subject to renewal 07/2019. DIVISION: 05 00
More informationDimensions Mechanical and Performance Requirements. Drop-In Anchors Hollow Wall, Steel Regular Style Drive Style...
Dimensions Mechanical and Performance Requirements Drop-In Anchors... 257 Hollow Wall, Regular Style... 258 Drive Style... 259 Hollow Wall, Plastic Ribbed... 260 Conical, Light Duty... 261 Fluted, Light
More informationMULE-HIDE PRODUCTS CO., INC FASTENER GUIDELINES
FASTENER GUIDELINES Fastener Overview A. Mule-Hide offers a variety of fasteners and plates to: Attach roof insulation Attach mechanically fastened roofing membranes Secure All Purpose Bar and termination
More informationSECTION CONCRETE ANCHORING. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 03 15 00 CONCRETE ANCHORING Display hidden notes to specifier. (Don't know how? Click Here) A. General purpose mechanical anchors for horizontal and vertical
More informationSECTION MASONRY ANCHORAGE AND REINFORCEMENT. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 04080 MASONRY ANCHORAGE AND REINFORCEMENT Display hidden notes to specifier. (Don't know how? Click Here) A. Post installed masonry anchors. B. Miscellaneous
More informationESR-1271* Reissued September 1, 2013 This report is subject to renewal July 1, 2015.
ICC-ES Evaluation Report www.icc-es.org (800) 4-6587 (56) 699-054 ESR-7* Reissued September, 0 This report is subject to renewal July, 05. A Subsidiary of the International Code Council DIVISION: 05 00
More informationThe Quick, Economical Method to Secure Hurricane Protection
The Quick, Economical Method to Secure Hurricane Protection The PanelMate hurricane anchoring system, the most recognized name for anchoring hurricane shutters, allows fast and easy installation in concrete,
More informationDIVISION: METALS SECTION: METAL FASTENINGS REPORT HOLDER: ELCO CONSTRUCTION PRODUCTS 1032 KERR DRIVE DECORAH, IOWA 52101
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-87 (2) 99-043 www.icc-es.org ESR-3332 Reissued 09/207 This report is subject to renewal 09/208. DIVISION: 0 00 00 METALS
More informationLENGTH IDENTIFICATION
58 Power-Bolt HEAVY DUTY, ELF-UNDERCUTTING LEEVE TYPE BAE MATERIAL Concrete, Block, Brick, tone IZE RANGE 1/4" x 1" to 1-1/4" x 9 MATERIAL LENGTH IDENTIFICATION The Power-Bolt anchor has a length identification
More informationREPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS EVALUATION SUBJECT: HILTI SELF-DRILLING AND SELF-PIERCING SCREWS
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2196 Reissued 10/2017 This report is subject to renewal 10/2019. DIVISION: 05 00
More informationALLIGATOR All-Purpose Anchors
ALLIGATOR All-Purpose s Description ALLIGATOR anchors are designed to hold high loads in solid walls, ceilings, and floors... but also hold securely when they encounter an unexpected cavity, such as in
More informationFlex Technology. Innovative Fastening Technologies The Industry Leader in Critical Fastening
Flex Technology Innovative Fastening Technologies The Industry Leader in Critical Fastening The Flex Technology Concept Standard case hardened fasteners are vulnerable to delayed embrittlement failures.
More informationMECHANICAL BACK FASTENED SYSTEMS INSTALLATION DATA
MECHANICAL BACK FASTENED SYSTEMS INSTALLATION DATA 7/16 PETRARCH ARCHITECTURAL WALL PANELS APPLIED OVER A STUDWALL BY MEANS OF A FIELD ASSEMBLED BACK FASTENED SYSTEM DESIGN CONCEPT 7/16 panels may be installed
More informationHang-TITE Rod Hanger Screws
Description The Hang-TITE Rod Hanger Screw is a one-piece, internally threaded anchor designed for suspending threaded rod for applications like cable-tray, pipe hanging, fire protection, and electrical
More informationINSTALLATION SHOP DRAWINGS FOR MINNEAPOLIS, MN
MINNEAPOLIS, MN 2-0- 2-- General Notes Abbreviations Deviations from Architectural Specifications Deviations from Architectural Drawings ALUM. = ALUMINUM B.O. = BY OTHERS CONT. = CONTINUOUS. = CLEARANCE
More informationProduct Submittal/Substitution Request
Product Submittal/Substitution Request TO: PROJECT: PROJECT LOCATION: SPECIFIED ITEM: Section Page Paragraph Description PRODUCT SUBMIT TAL / SUBSTITUTION REQUESTED: The attached submittal package includes
More informationTI: Efficient self tapping fasteners into concrete without plugs
TI: Efficient self tapping fasteners into concrete without plugs Application specific fastener solutions for use either with solid or pre-cast concrete substrates are highly sought after. Indeed, some
More informationGCN150 Gas-Actuated Concrete Nailer
GCN0 Gas-Actuated Concrete Nailer The GCN0 gas-actuated concrete nailer is a portable fastening tool for attaching light-duty fixtures such as drywall track, furring strips, hat track and angle track to
More informationC O N S T R U C T I O N F A S T E N E R S S T E E L POWDER ACTUATED CARBIDE DRILL BITS
C O N S T R U C T I O N F A S T E N E R S F O R C O N C R E T E & S T E E L MECHANICAL ANCHORS ADHESIVE ANCHORS HOLLOW WALL ANCHORS POWDER ACTUATED GAS FASTENING ROOFING FASTENERS CARBIDE DRILL BITS INTRODUCTION
More informationPRICE BOOK NO. 204S ORDERING INFORMATION
Container Quantities PRICE BOOK NO. 204S ORDERING INFORMATION Replacing Catalogue 789S Effective March, 2007 and Packaged items are supplied in full containers and we reserve the right to adjust order
More informationShapes Siding. Perfection Shingles. Chalk Line
Snap a Chalk Line Shapes Siding Perfection Shingles Chalk Line To establish a straight reference line to guide the positioning of the starter strip and the first course of siding, snap a chalk line. starter
More informationMulti-Set II Drop-In Anchors
CONCRETE ANCHORING SPECIALISTS Internally Threaded Heavy- Duty Anchoring Systems DESCRIPTION/SUGGESTED SPECIFICATIONS Drop-In, Shell-Type Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE Drop-In, shell-type
More information#14 ¾" A 5 #14 1" A 5 #14 1-½" A 5 #17 1" AB 3 #14 ¾" A 3 #14 1" A 3 #14 1½" A 3
ACCESSORIES SELF-TAPPING CARBON STEEL #14 ¾" A 5 16" 13.2# 81.00 95.25 #14 1" A 5 16" 17.0# 94.90 109.15 #14 1-½" A 5 16" 21.0# 110.80 125.05 #17 1" AB 5 16" 16.0# 158.25 172.50 when using this type of
More informationACCESSORIES #14 1" A 5 #14 1-½" A 5 #17 1" AB 5. Note: Fasteners sold in quantities of 250 only. #14 1" A 3 #14 1½" A 3 #17 1" AB 3
SELF-TAPPING CARBON STEEL #14 ¾" A 5 16" 13.2# 81.00 95.25 #14 1" A 5 16" 17.0# 94.90 109.15 #14 1-½" A 5 16" 21.0# 110.80 125.05 #17 1" AB 5 16" 16.0# 158.25 172.50 when using this type of fastener 304
More informationREPORT HOLDER: ISAIAH INDUSTRIES, INC. EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1360 Reissued 08/2018 This report is subject to renewal 08/2019. DIVISION: 07 00
More informationDirectly from the Manufacturer: Mechanical Fastening Systems for the Truck and Trailer Industry
Directly from the Manufacturer: Mechanical Fastening Systems for the Truck and Trailer Industry Table of Content Competence and performances to your benefits 1 Product index 2 Floor assembly Product families:
More informationSELF DRILLING PANEL FASTENER CATALOG 2012
SELF DRILLING PANEL FASTENER CATALOG 2012 Metal Roofing Fasteners and Accessories for exposed fastener and concealed fastener panels. Products for residential and commercial metal roofing. Steel Building
More informationSubmittal Sheet. Product: Item# Description Unit Pack
Submittal Sheet Submittal Sheet #0309412 Bugle Head Screws (212) Product: Item# Description Unit Pack C368 6 x 1-1/4-in, Bugle Head, Fine Thread,, Phosphate, Collated 1,000 1268YZ 10 x 3-1/2-in, Bugle
More informationFASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S. Which FERO Tie Systems Require Fasteners?
FASTENERS C O M P AT I B L E W I T H F E R O T I E S Y S T E M S Which FERO Tie Systems Require Fasteners? Structural Actions: Fastener,, or Both? With the exception of FERO tie systems that are directly
More informationSigma Fasteners, Inc. Section 7
DESCRIPTION PAGE s Wedge s 7-1 Drop-In s 7-2 Single Expansion s 7-2 Machine Screw s 7-2 Lag Shields 7-3 Lead Wood Screw s 7-3 Hammer Drive s 7-4 Hollow Wall Fasteners 7-5 Toggle Bolts 7-6 Toggle Wings
More informationLetter of Transmittal/Submittal
Letter of Transmittal/Submittal FROM: TO: Baker Concrete Construction 1904 Jasper Street DATE JOB NUMBER 09/23/10 Aurora, CO 80011 9921 303.367.8111 ATTENTION Nick Dewald 937.536.9000 RE: Bruce Herman
More informationPowder Actuated Fasteners - Drive Pins
122 Drive Pins Standard Pins Drive pins with a.300 diameter head are designed for permanently fastening a fixture to concrete, some types of masonry and A36 structural steel. Drive pins are manufactured
More informationMetal Roof Installation Manual. Chapter 14: Fasteners
Metal Roof Installation Manual Chapter 14: Fasteners Chapter 14: Fasteners Chapter Contents 14. Introduction... 14-1 14.1 Fastener Parts and Installation... 14-1 14.1.1 Points... 14-1 14.1.2 Heads... 14-1
More informationUmbrella Inserts and Stubby Screens
ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7+ Adhesive Umbrella Inserts
More informationFlex Technology. Innovative Fastening Technologies The Industry Leader in Critical Fastening
Flex Technology Innovative Fastening Technologies The Industry Leader in Critical Fastening The Flex Technology Concept Standard case hardened fasteners are vulnerable to delayed embrittlement failures.
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2013 Hilti North American Product Technical Guide Volume 1 Direct Fastening. For complete details on this product, including data development, product specifications, general
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: SCREW PRODUCTS, INC.
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3654 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 06 00
More informationRELINER INSIDE DROP SYSTEM SPECIFICATIONS
1. PRODUCT NAME RELINER INSIDE DROP SYSTEM U.S. Patent 6074130 Canadian Patent # 2269565 All RELINER Products are proudly made in the U.S.A. 2. MANUFACTURER RELINER /Duran Inc. 53 Mount Archer Rd. Lyme
More informationT3ss Gas Powered Tool
T3ss Gas Powered Tool Gas Technology Single Pin Gas Tool Fuel Injection Cross Over Technology /SUGGESTED SPECIFICATIONS Crossing Over from Powder to Gas THE PREMIER FASTENING SYSTEM FOR THE ELECTRICAL
More informationDIVISION: METALS SECTION: METAL FASTENINGS DIVISION: FINISHES SECTION: FASTENERS REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1408 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 05 00
More informationHollo Set Drop-In Anchors
Description The Hollo Set drop-in anchor is an internally threaded, flush mount expansion anchor designed for use in hollow and solid base materials. In hollow concrete block and precast hollow core plank,
More informationAmerican Safe Room. Explosion Resistant Blast Hatch with Integrated Riser
American Safe Room Explosion Resistant Blast Hatch with Integrated Riser Drawing: ASR-50-RBH Revision: H May 17, 2012 Table of Contents Description... 3 Options... 4 Order form... 5 Option: left or right
More informationCOMPOSITE SIDING INSTALLATION GUIDE
CENTURY HOME LIVING COMPOSITE SIDING INSTALLATION GUIDE Read all instructions prior to installing any siding product. Failure to install and finish this product in accordance with all local building codes,
More informationROOFSAFE ANCHOR & CABLE
Installation Instructions ROOFSAFE ANCHOR & CABLE THE ULTIMATE IN FALL PROTECTION MANUAL Contents Guidelines for Installation 3 Top Bolt Installation 4 Toggle Installation 5 Concrete Installation 6 Component
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationBITS, NUTSETTERS, ADAPTERS
BITS, NUTSETTERS, ADAPTERS Square Recess Power Driver Bits... Colour-Coded Square Recess Power Driver Bits... Phillips Power Driver Bits... 6 Colour-Coded Phillips Power Driver Bits... 7 Six Lobe Power
More informationBUILDING FASTENERS METAL TO METAL FASTENERS
BUILDING FASTENERS METAL TO METAL FASTENERS PAINT + TESTING PaintingOptions MATCHTECH The world s best fasteners now in any color, any time. MatchTech is Marco Industries stateofthe art, high quality polyurethane
More informationWedge Type Anchors. Trubolt. Wedge Anchor ADVANTAGES
CONCRETE ANCHORING SPECIALISTS Dependable, Heavy-Duty, Inspectable, Wedge Type Expansion Anch 2015 IBC Compliant DESCRIPTION/SUGGESTED SPECIFICATIONS Wedge Type Anchs SPECIFIED FOR ANCHORAGE INTO CONCRETE
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationComplete line of Holemaking Products and Accessories
Complete line of Holemaking Products and Accessories I N T R O D U C I N G Holemaking Products Klein Tools has expanded our line of Holemaking products. We have added new flexible drill bits and related
More informationHUS 6 Screw anchor, Redundant fastening
HUS 6 Screw anchor, Anchor version HUS-A 6 Carbon steel Concrete Screw with hex head HUS-H 6 Carbon steel Concrete Screw with hex head HUS-I 6 Carbon steel Concrete Screw with hex head Benefits - Quick
More informationEvaluation of In-Pavement Light Fixture Designs and Performance
Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of
More informationPRODUCT EVALUATION Effective July 1, 2009 RC-204
TEXAS DEPARTMENT OF INSURANCE Engineering Services / MC 103-3A 333 Guadalupe Street P.O. Box 149104 Austin, Texas 78714-9104 Phone No. (512) 322-2212 Fax No. (512) 463-6693 PRODUCT EVALUATION Effective
More informationMTS-ACB. RENOGY Photovoltaic Module Adjustable Curved Bracket E Philadelphia St, Ontario, CA Version: 1.
MTS-ACB RENOGY Photovoltaic Module Adjustable Curved Bracket 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.0 Important Safety Instructions Please save these instructions. This manual
More informationCITY OF LOS ANGELES CALIFORNIA
BOARD OF BUILDING AND SAFETY COMMISSIONERS VAN AMBATIELOS PRESIDENT E. FELICIA BRANNON VICE-PRESIDENT JOSELYN GEAGA-ROSENTHAL GEORGE HOVAGUIMIAN JAVIER NUNEZ CITY OF LOS ANGELES CALIFORNIA ERIC GARCETTI
More informationDIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC AND COMPOSITE FASTENINGS REPORT HOLDER: DEWALT
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3164 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 06 00
More informationTHE ENGINEERED WOOD ASSOCIATION
D A T A F I L E APA Performance Rated Rim Boards A rim board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top
More informationBuyers Guide. Pg. 74 Bronze Screws High Speed Drill Bits Pg. 106 Packaged Fasteners Pg. 108
Buyers Guide 2 0 1 2-2 0 1 3 Mechanical Anchors Pg. 4 Adhesive Anchors Pg. 25 Light Duty Anchors Pg. 34 Powder & Gas Fastening Pg. 40 Carbide Drill Bits Pg. 62 Zinc, SS, Brass & Pg. 74 Bronze Screws High
More informationFNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson.
FASTENERS PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. Quick Reference Nuts Heavy Hex Nuts...4
More informationSelf-drilling fasteners in the most popular sizes
Self-drilling fasteners in the most popular sizes Self-drilling fasteners eliminate separate drilling and tapping operations for faster, more economical installations. Diameters: #8 to 5/16" Lengths: 1/2"
More informationICC-ES Evaluation Report
ICC-ES Evaluation Report ESR-6 Reissued April, 009 This report is subject to re-examination in two years. www.icc-es.org (800) 4-6587 (56) 699-054 A Subsidiary of the International Code Council DIVISION:
More informationInnovative Fastening Technologies
Innovative Fastening Technologies 2011 Construction Products Catalog Flex Technology Metal Fastening Systems Concrete Anchoring Systems Building Protection Drill Screws Table of Contents Stalgard High-Performance
More informationTrusted ICC ES. Issued 06/2018 HILTI, INC. Evaluation. report, or as to any. ICC-ES Evaluation
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 4185 Issued 06/2018 This report is subject to renewal 06/2019. SECTION: 05 05 23
More informationCOMPATIBILITY OF FASTENERS
COMPATIBILITY OF FASTENERS TECHNICAL BULLETIN Vol. 4, No. 2 NOVEMBER 2011 This bulletin applies to conditions where fasteners are not provided by Metl-Span. Profiled metal roof or wall panels rely upon
More information