YEAR 9 MATERIALS TECHNOLOGY PINE STORAGE BOX KNOWLEDGE BOOKLET
|
|
- Candace Tyler
- 6 years ago
- Views:
Transcription
1 YEAR 9 MATERIALS TECHNOLOGY PINE STORAGE BOX KNOWLEDGE BOOKLET You will be set homework once every two weeks. The information you need to learn is contained in this booklet. There will be a short test at the beginning of the lesson to test what you have learnt.
2 Homework 1: Health and Safety Any workshop is potentially a very dangerous place unless safe working practices are followed. 10 Health and Safety Rules 1. Always listen carefully to the teacher and follow instructions immediately. 2. Do not run in the workshop, you could bump into another student and cause an accident. 3. Always put your hand up if you need help as shouting out can cause a distraction and lead to an accident. 4. Always wear the appropriate Personal Protective Equipment (PPE) for the task being undertaken. 5. All bags and stools should be safely stored away from the work area as they are trip hazards. 6. When learning how to use equipment, listen very carefully to all the instructions given by the teacher. Ask questions if you do not fully understand. 7. Do not use a machine if you have not be shown how to operate it safely by the teacher. Always ask for permission before you turn it on. 8. Only one person must operate a machine at a time. 9. Only have one person inside the yellow / black hazard markings around a machine. 10. Do not distract others whilst they are working as this may cause an accident. Homework 1 Learn the safety rules listed and learn to recognise the safety symbols.
3 Homework 2: Tools and Equipment The workshop includes portable hand-tools and larger fixed equipment. Image Name Description Disc sander An electrically powered sanding disc used to sand wood. NB. Extraction must be used. Tri-square The wooden handle is fixed at 90⁰ (i.e. square) to the steel blade. Used to mark out a line square to an edge or to check for square. Marking gauge The adjustable stock is set the required distance from the metal pin. Used to mark lines parallel to an edge. Coping saw The thin blade may be adjusted to any angle. Used to cut curves in wood. Tenon saw A type of back saw with a stiff deep blade used to produce straight cuts / joints in wood. Homework 2 Learn the name, correct spelling and use of the tools shown in the table.
4 Homework 3: Risk Assessment Most workshop processes or activities are assessed for potential hazards and measures to minimize or control the hazard identified. Companies are required by law to carry out regular risk assessments of the equipment / processes they use. A Risk Assessment for the Pillar drill. Hazard Swarf (metal particles) or sawdust going into eyes Work spinning on the machine table Hair or lose clothing getting caught in rotating parts Drilling hand / fingers Getting a friend to help you The chuck key flying out of the chuck Leaving the Pillar drill switched on Control Measure Use the guard on the pillar drill and wear safety goggles Clamp the work to the machine table or use a machine vice (clamped to the machine table) Tie up long hair, remove lose clothing and wear an apron Clamp work or use a machine vice and avoid distractions Only have one person operating the pillar drill Never leave the chuck key in the chuck Remember to switch the pillar drill off once you have finished using it Homework 3 Learn the hazards and control measures that must be used when using the pillar drill. Identify the hazards and associated control measures when using the disc sander?
5 Homework 4: Glues and Adhesives Adhesives are used to bond materials together to form a permanent joint. There are a wide variety of adhesives available and it is important to select the correct one for the task and to use if safely. Name Material Drying / Cure Time Description / Use PVA Polyvinyl acetate Wood 4-24 hours Can be used straight from the bottle or brushed on to provide a strong joint. Parts need to be dry and clamped together while the Contact adhesive E.G. Evostick Hot glue stick Cyanocrylate (super glue) Liquid Solvent Cement (Tensol) Wood, metal and plastic Wood, metal and plastic Wood, metal and plastic Instant On cooling Instant Thermoplastics 10 minutes glue cures. A medium strength waterproof joint. Comes in liquid form and is applied using a spreader A waterproof adhesive but is relatively weak. Only suitable for modelling or temporary fixings. The glue stick is heated in a special glue gun. A waterproof, medium strength adhesive. Available, ready to use, in liquid form. Only suitable for small surface areas. A waterproof, medium strength joint. Comes in liquid form and is applied using a brush. Joints need to be held together while glue cures. Health and Safety: It is very important that adhesives are used safely. Read the instructions supplied with the product and follow them carefully. Remember also that materials need preparing before the adhesive is used. Homework 4 Learn the information on the different adhesives. What adhesive will you need to use to make the storage box?
6 Homework 5: Manufactured Boards Manufactured boards are made by converting logs into strips, veneers, chips or tiny particles, depending on the type of board being manufactured and then gluing them together to form sheet materials. Manufactured boards are stronger, more stable and more uniform than wide boards of either hardwood or softwood. Plywood Blockboard Manufacturing process Veneers glued together with each layer having the grain direction at rightangles to the previous one Strips of softwood glued side by side and then covered with a veneer on both sides Properties Flat, stable boards with uniform strength and thickness. Interior and exterior grades available A very strong and stable board Uses Furniture, boat building. Furniture Chipboard Medium Density Fibreboard MDF Thousands of tiny woodchips are mixed with glue and then compressed into sheets Tiny particles of wood are glued together and compressed with an adhesive to produce large, dense solid boards A low cost board. Difficult to join together, easily damaged by moisture A solid and stable board. Easily damaged by moisture Kitchen worktops when covered with a protective surface, flooring. Furniture, kitchen units, flooring. Hardboard Pulped wood treated to form fluffy brown fibres, mixed with glue and then compressed to form sheets A very low cost board, uniform strength in all directions. Cupboard backs, drawer bases. Homework 5 Learn the information on manufactured boards. Which manufactured board will be suitable to make the lid of the storage box?
Tuck tie in shirt, roll up sleeves, wear protective apron or lab. coat. High risk
Risk Assessment Exercises The table below lists some typical D&T activities and the risks involved in carrying them out. Assess each activity as either a high risk, low risk or no risk activity and state
More informationPINE WOODS OAK METALS POLYMERS ASH SOFTWOODS CHIPBOARD MAHOGANY MAN MADE HARDWOOD WOODS MDF PLYWOOD BEECH HARDBOARD THERMOSET FERROUS METALS CARBON
ASH PINE MAHOGANY SOFTWOODS CHIPBOARD HARDWOOD MAN MADE WOODS OAK WOODS MDF PLYWOOD BEECH HARDBOARD RESISTANT METALS MATERIALS ALUMINIUM POLYMERS NON-FERROUS METALS UREA FORMALDEHYDE COPPER ZINC THERMOSET
More informationS2 Exam: Manufacturing
S2 Exam: Manufacturing The choice of materials and manufacturing processes plays a significant role in design of various products. In order to explore these fully the designer must be aware of the properties
More informationPiXL Independence. Technology Answer Booklet KS4. Wood. Contents: I. Multiple Choice Questions 10 credits in total
PiXL Independence Technology Answer Booklet KS4 Wood Contents: I. Multiple Choice Questions 10 credits in total II. III. Shorter Answer Questions 10 credits each Exam Style Questions 100 credits each 1
More informationDesign and Technology Resistant materials Key words and definitions
Design and Technology Resistant materials Key words and definitions Word Acrylic Definition a type of thermoplastic, which is hard and can be transparent. Used to make shop signs. Perspex is a trade/brand
More informationDesign and Manufacture JOINING
Design and Manufacture JOINING Introduction Different materials require different tools. These tools and joints are used when joining wood: Finger Dovetail Housing Dowel Cross halving Corner Lap Mortise
More informationʻ L e o n a r d o d a V i n c i ʼ s gear machineʼ
1 0 0. 9 1 7 ʻ L e o n a r d o d a V i n c i ʼ s gear machineʼ Autore Covolan Girolamo Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for
More informationUnit 2 Engineered Panels
Unit 2 Engineered Panels MULTICHOICE 1. What is another name for large, reconstituted wood sheets or panels? (A) formed panels (B) engineered panels (C) architectural panels (D) construction panels 2.
More informationSAFETY INFORMATION PACKET
WILLOWCREEK MIDDLE SCHOOL SAFETY INFORMATION PACKET GENERAL SHOP SAFETY 1 WIDE BELT SANDER 2 BAND SAW 3 MITER SAW 4 UP- CUT SAW 4 PLANER 6 TABLE SAW 7 DRILL PRESS 8 LATHE 8 DISK / VERTICAL BELT SANDER
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationNojo Design: Large Step Cabinet: February 2012
Nojo Design: Large Step Cabinet: February 2012 The largest single piece of furniture I ve ever made is this stepped cabinet. Finished piece is 8! tall and over 10 long. This project has been great, although
More informationGCSE Resistant Materials Year
Term Resistant Materials knowledge/skills Using and Applying Grade Criteria The importance of and how to measure and cut Be able to mark out a comb joint accurately and cut it wood accurately and repeatedly
More informationAQA GCSE Design and Technology 8552
AQA GCSE Design and Technology 8552 Natural and manufactured timbers Unit 3 Materials and their working properties 2 Objectives Know the primary sources of materials for producing natural and manufactured
More informationDefinitions. Forestry 240 Wood Science
Definitions Forestry 240 Wood Science Chapter 15 Nonstructural Panels Panel products made from wood-based veneer and particle products that are not suitable for structural applications. Used for Decorative
More informationMan-made board page 1
Man-made board page 1 general - plywood - chipboard - edge laminated softwood board - blockboard - hardboard - mdf - stirling board General Store any sheet material in dry conditions, stacked flat. Do
More informationPneumatic Robot arm/digger
1 0 6. 1 8 6 Pneumatic Robot arm/digger Please Note The OPITEC range of projects is not primarily intended as toys for young children. It is for teaching, designing and making to ensure that pupils experience
More informationChopper Motorcycle. Warning! This product contains small parts that can be swallowed. There is a danger of choking E101980#1
1 0 1. 0 Chopper Motorcycle Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft, Design and Technolo-
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationWater Wheel. Autore Covolan Girolamo
1 0 0. 9 0 6 Water Wheel Autore Covolan Girolamo Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of
More informationDIEBOARDS & PLYWOOD. Flat Dieboards. Rotary Dieboards. Plywood. Other Sheet Materials
DIEBOARDS & PLYWOOD In addition to supplying the highest quality pattern grade lumbers for over 100 years, Freeman offers flat and rotary dieboards, a variety of high-grade, economical plywoods, and specialty
More informationMake a cupboard as a BCATS
National Certificate in Building, Construction, and Allied Trades Skills (BCATS) Make a cupboard as a BCATS project Unit Standard 25921 Level 2, Credit 6 Name: Contents Reference Page What you need to
More informationGCSE Resistant Materials. Revision
GCSE Resistant Materials Revision 1 Match the manufactured board with the explanation A B C D E 2 Which wood would normally be used to make this product and why? a. Scots Pine b. Cedar c. Parana Pine d.
More informationGCSE 4111/01 DESIGN AND TECHNOLOGY UNIT 1 FOCUS AREA: Resistant Materials Technology
Surname Centre Number Candidate Number Other Names 0 GCSE 4111/01 DESIGN AND TECHNOLOGY UNIT 1 FOCUS AREA: Resistant Materials Technology A.M. TUESDAY, 24 May 2016 2 hours S16-4111-01 For s use Question
More informationSurface planer or buzzer. Performs the tasks of dressing, squaring and straightening timber Machining short lengths of timber. Without the bridge guard. Without the appropriate training. Without PPE. Set
More informationMaking a Finished Product from Wood (National 4) level 4 (6 SCQF credit points)
Making a Finished Product from Wood (National 4) SCQF: level 4 (6 SCQF credit points) Unit code: H25Y 74 Unit outline This is the Added Value Unit in the National 4 Practical Woodworking Course. The general
More information5. Timber Application, Products and their use
TIMBER 5. Timber Application, Products and their use Lecturer: Prof. Dr. Mohammad Ismail Faculty of Civil Engineering, -Skudai, Johor Darul Ta zim, MALAYSIA 1 Room : C09-313 Tel : 07-5531688 December 6,
More information7th/8th Grade Industrial Tech General Safety. Give your undivided attention to the machine in which you are using.
7th/8th Grade Industrial Tech General Safety Wood Lab Safety General Safety Always wear safety glasses. Report all injuries to the instructor. No baggy clothing or open toed shoes. Give your undivided
More informationINTRODUCTION TO WORKSHOP SAFETY
WEEK 12 INTRODUCTION TO WORKSHOP SAFETY Safety is a major importance in any craft room. It is imperative that safe working practices are observed at all times. Failure to observe safety rules will result
More information*0600/401* 0600/401. CRAFT AND DESIGN STANDARD GRADE Foundation Level. Fill in these boxes and read what is printed below. Full name of centre
FOR OFFICIAL USE F 6/4 NATIONAL QUALIFICATIONS 29 MONDAY, 8 MAY 9. AM. AM Total CRAFT AND DESIGN STANDARD GRADE Foundation Level Fill in these boxes and read what is printed below. Full name of centre
More information2008 VCE VET Furnishing GA 2: Written examination
VCE VET Furnishing GA 2: Written examination GENERAL COMMENTS In, the number of students sitting for the VCE VET Furnishing written examination increased slightly from the previous year from 266 to 296.
More informationYear 8 Textiles KNOWLEDGE BOOKLET. You will be set homework every 2 weeks.
Year 8 Textiles At the end of this unit you will have an assessment. 50% = The quality of the Textiles cushion cover you have made 50% = The information you have learnt KNOWLEDGE BOOKLET You will be set
More information0445 DESIGN AND TECHNOLOGY
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education www.xtremepapers.com MARK SCHEME for the October/November 2011 question paper for the guidance
More informationJUNIOR CERTIFICATE 2008 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A
JUNIOR CERTIFICATE 2008 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A 1 SECTION A - Sht Answers Mark all questions, select the best 16 questions This section is marked out of 80 marks.
More informationGuild of Oregon Woodworkers Shop Safety Test
Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100% Make sure you put the answers under the correct portion of the answer sheet for the
More information*0600/401* 0600/401. CRAFT AND DESIGN STANDARD GRADE Foundation Level. Fill in these boxes and read what is printed below. Full name of centre
FOR OFFICIAL USE F 6/4 NATIONAL QUALIFICATIONS 28 WEDNESDAY, 4 MAY 9. AM. AM Total CRAFT AND DESIGN STANDARD GRADE Foundation Level Fill in these boxes and read what is printed below. Full name of centre
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission JUNIOR CERTIFICATE 2010 MARKING SCHEME MATERIALS TECHNOLOGY WOOD ORDINARY LEVEL
Coimisiún na Scrúduithe Stáit State Examinations Commission JUNIOR CERTIFICATE 2010 MARKING SCHEME MATERIALS TECHNOLOGY WOOD ORDINARY LEVEL JUNIOR CERTIFICATE 2010 MATERIALS TECHNOLOGY (WOOD) MARKING
More informationIndustry Related Manufacturing Technology
Industry Related Manufacturing Technology Focus Area: Timber Products and Furniture Technologies (Preliminary) Materials Timber and timber products structure: sapwood heartwood earlywood latewood cambium
More informationCarpentry Canadian 3rd Edition Vogt TEST BANK Full download at:
UNIT 5 Carpentry Canadian 3rd Edition Vogt SOLUTIONS MANUAL Full download at: https://testbankreal.com/download/carpentry-canadian-3rd-editionvogt-solutions-manual/ Carpentry Canadian 3rd Edition Vogt
More informationPlan #1 Wooden hinge, single action
Plan #1 Wooden hinge, single action There are two types of wooden hinges, a single action hinge (that is in effect a finger joint with a pin through it) and a double action hinge which has two pins. The
More informationIndustrial Technology Timber Products and Furniture Technologies
2010 HIGHER SCHOOL CERTIFICATE EXAMINATION Industrial Technology Timber Products and Furniture Technologies Total marks 40 General Instructions Reading time 5 minutes Working time 1 1 hours 2 Write using
More information6043 DESIGN AND TECHNOLOGY 6043/01 Paper 1 (Technology), maximum raw mark 95
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS GCE Ordinary Level MARK SCHEME for the October/November 2009 question paper for the guidance of teachers 6043 DESIGN AND TECHNOLOGY 6043/01 Paper 1 (Technology),
More informationBenchwork and Roadbed
Metro-North Division January 16, 2016 Benchwork and Roadbed Considerations and Suggestions Topics to discuss Different types of benchwork Styles of sub-roadbed What type of lumber? dimensional or plywood?
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationPRODUCT CATALOGUE WOOD PRODUCTS:
2009 200 PRODUCT CATALOGUE WOOD PRODUCTS: VitalWOOD VitalWOOD MDF MDF Melamine Boards VitalFLOOR HDF Laminated Flooring VitalPLY Plywood VitalPLY WBP Marine Plywood VitalBOARD Hard Board BMD sales@vital.com.sg
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationNational 5 Practical Woodwork
Exercise C. The legs of a chair are turned on the wood lathe. (a) (i) Sketch and name the tool used to produce the square shoulder shown at A. Name of tool: Sketch and name the tool used to check the diameter
More informationJUNIOR CERTIFICATE 2005 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A
JUNIOR CERTIFICATE 2005 MATERIALS TECHNOLOGY (WOOD) MARKING SCHEME ORDINARY LEVEL SECTION A NOTE Please ensure that totals for each question are divided by two before entering marks on marking sheets.
More informationWestern Illinois University Department of Art Woodshop Orientation
Western Illinois University Department of Art Woodshop Orientation SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationTimberflex & Flexboard Technical Guide
Timberflex & Flexboard Technical Guide A bendable substrate material that can be formed first and laminated last Patent #5,618,601; #5,232,762; #5,824,382 Doors Larger radius and small doors are easily
More informationVCE VET FURNISHING (CABINET MAKING)
Victorian Certificate of Education 2012 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET FURNISHING (CABINET MAKING) Written examination Section Monday 12 November
More informationFinishes and Finishing Techniques
Finishes and Finishing Techniques TED 126 Spring 2007 Review pages 147-150, 284-294 Finishes and finishing techniques The finishing process to choose depends partly on the type of wood and the appearance
More information1. Pupils need to have an understanding of hygiene rules that need to be considered before and during practical work.
Food: Objectives 1. Pupils need to have an understanding of hygiene rules that need to be considered before and during practical work. 2. Pupils need to be able to identify equipment and be able to give
More informationFABRICATING ARBOR. koroseal.com/arbor Arbor Veneered Components
Arbor Veneered Components Arbor natural wood veneer can be applied to any substrate and is flexible enough to be formed around the tightest radii providing the ultimate wood finish. From vertical wall
More informationInstructions for Turning Laminated Bracelets
Instructions for Turning Laminated Bracelets 1. Start with Design 1. Make a paper template circle for the bracelet. Use this to check the fit on the person you are making the bracelet for. After checking
More informationWESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART
WESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART WOODSHOP ORIENTATION SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationPortable circular saw Used to cut a wide range of construction materials Check the cord, leads and 3 pin plugs for any damage. A Residual Current Device (RCD) is plugged into the power source. Do not stand
More informationArched. Building an. Passageway. Although my company specializes in high-end jobs
Building an Arched Passageway All photos by Brian Striegler This straightforward approach combines basic shop methods with simple site joinery to create an elegant frame-and-panel archway by Gary Striegler
More informationFramework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd
FABRICATION - WOOD JOINTS The word: fabricate means to join together. Most wooden products are held together with adhesive. Adhesive works very well when the edge of a piece of wood is being glued to the
More informationMaterials Design and Technology General Course Year 12. Selected Unit 3 syllabus content for the. Externally set task 2018
Materials Design and Technology General Course Year 12 Selected Unit 3 syllabus content for the Externally set task 2018 This document is an extract from the Materials Design and Technology General Course
More information2017 VCE VET Furnishing examination report
2017 VCE VET Furnishing examination report General comments The 2017 VCE VET Furnishing examination assessed students underpinning knowledge of the competencies they had undertaken in Units 3 and 4 as
More informationHomemade Sanding Tools David Hoehns
Homemade Sanding Tools David Hoehns allskewedup@gmail.com 806 789 5108 My demonstration will focus on two types of homemade sanding devices, a foam ball sander that may be used for power sanding concave
More informationCambridge International Examinations Cambridge International General Certificate of Secondary Education
Cambridge International Examinations Cambridge International General Certificate of Secondary Education *8202623436* DESIGN AND TECHNOLOGY 0445/33 Paper 3 Resistant Materials May/June 2018 1 hour Candidates
More information0445 DESIGN AND TECHNOLOGY
CAMBRIDGE INTERNATIONAL EXAMINATIONS Cambridge International General Certificate of Secondary Education www.xtremepapers.com MARK SCHEME for the October/November 2014 series 0445 DESIGN AND TECHNOLOGY
More informationBird Feeder. Tool Requirements
Bird Feeder Written and constructed by Craig Tilley This wooden bird feeder will be an attractive addition to your garden. Its wide trays allow plenty of room for birds to come and have a snack, and the
More informationThis article was written by Phill Brander (AUS), who has built many timber catamarans including a Paper Tiger.
Building a Paper Tiger Catamaran Scarfing Plywood Paper Tiger Catamaran GUIDES Warnings/Cautions As always, using any power tools, cutting implements or adhesives carries certain risks. Make sure you understand
More informationA strong clear liquid that bonds most materials in seconds. A quality product for the DIY enthusiast Great for emergency repairs.
Superglue Super Glue 3G - 3 s A strong clear liquid that bonds most materials in seconds. A quality product for the DIY enthusiast Great for emergency repairs. Super Glue 3G - Single A strong clear liquid
More informationTech Ed Lab Safety SAFETY RULES Page 1-1
SAFETY RULES Safety Rules for Working with Wood 1. Secure your instructor s approval for all work you do in the shop. 2. Wear safety glasses when doing any operation that may endanger your eyes. 3. Always
More informationALONA YANSHINA EXERCISE 1.1
material makeup: log ALONA YANSHINA EXERCISE 1.1 timeline + development log cabin - interlocked corners by cutting notches in the ends of the logs. using log joinery technique, structures grew higher logs
More informationAhead of the curve 2 Part
F&C PROJECT Ahead of the curve 2 Part In the second part of this series, Chris Tribe constructs the table for his stylised cabinet which we looked at last month in F&C Accuracy in turning the legs for
More informationWoodwork Level 3, 3N0589
Page 1 Woodwork Level 3, 3N0589 Student Name: Student PPSN: Tutor: Date: Copyright 2016 Janna Tiearney, Educoot 1 Page 2 This workbook and accompanying ebook is by courtesy of The Woodwork Department Loughan
More informationART SCULPTURE LAB SAFETY POLICIES AND PROCEDURES. In case of Emergency or Accident: Be aware of the location of the a phone to call
The following is an explanation of the policies, operations, safety practices, and use of this facility. Objective: The Art Sculpture Lab is a community workshop for the intended purpose of offering the
More informationGeneral Purpose Flat Wagon
General Purpose Flat Wagon This is a freelance model of a flat wagon used by any number of railways for transporting large and awkward loads. The kit includes optional load securing rings and a pair of
More informationG. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
More informationEZYSTONE WORKSURFACES
EZYSTONE WORKSURFACES Installation & Maintenance Instructions 1. Tools Required Worktop Edge Finishing Kit Pack 1-100mm Velcro Backing Pad Pack 2-100mm Diamond Dry Cut Velcro Discs (100 Grit Yellow) (200
More informationCalderside Academy. Technical Department. Standard Grade Craft & Design. Knowledge & Understanding In Wood. Page
Calderside Academy Technical Department Standard Grade Craft & Design Knowledge & Understanding In Wood Page Knowledge and understanding of Wood Throughout the world there are thousands of different species
More informationCambridge International Examinations Cambridge International General Certificate of Secondary Education
www.xtremepapers.com Cambridge International Examinations Cambridge International General Certificate of Secondary Education *0816121761* DESIGN AND TECHNOLOGY 0445/31 Paper 3 Resistant Materials May/June
More informationHANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining
HANDCRAFTED LIDDED CHEST IN CHERRY With Red Cedar Lining Design A chest was desired as a gift to family. The Shaker style of furniture was identified as a pleasing style. After viewing a number of pictures
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationReplicate/restore wooden components of furniture
Replicate/restore wooden components of furniture Overview This standard addresses the competence required to make wooden components for hand-crafted furniture. This involves: 1 cutting, shaping and moulding
More informationWOOD + LATEX. Alles Wise 3d Design and Craft 2017
WOOD + LATEX Alles Wise 3d Design and Craft 2017 What is comfort? Relaxation Indulgence Comfort Comfort can often be seen as incredibly indulgent and often a wasteful pursuit. In the current status quo,
More informationBuild your own Drawer unit. D3 / D4
Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,
More informationCabinetmaking & Millwork CIP Task Grid
1 Secondary Task List 100 FOLLOW RULES FOR WORKING IN THE CABINETMAKING LAB. 101 Review and discuss school rules. 102 Review and demonstrate knowledge of cabinetmaking lab rules. 103 Complete all theory
More information6043 DESIGN AND TECHNOLOGY
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS GCE Ordinary Level MARK SCHEME for the October/November 2010 question paper for the guidance of teachers 6043 DESIGN AND TECHNOLOGY 6043/01 Paper 1, maximum
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More information6043 DESIGN AND TECHNOLOGY
www.onlineexamhelp.com www.onlineexamhelp.com CAMBRIDGE INTERNATIONAL EXAMINATIONS GCE Ordinary Level MARK SCHEME for the October/November 2013 series 6043 DESIGN AND TECHNOLOGY 6043/01 Paper 1, maximum
More informationLGCSE DESIGN AND TECHNOLOGY 0189 REPORT FOR TEACHERS
LGCSE DESIGN AND TECHNOLOGY 0189 REPORT FOR TEACHERS The 2016 Design and technology Paper was composed of 16 questions of which 10 of them formed part A and were compulsory and contributed 28 marks. These
More information25-Sep-17. SPECIES, SITE, SOIL, CLIMATE, MICROCLIMATE, WEATHER, GENES etc
SPECIES, SITE, SOIL, CLIMATE, MICROCLIMATE, WEATHER, GENES etc 1 Pine Spruce Grading use 2 WOOD 3 WOOD: CELLULOSE HEMICELLULOSES LIGNIN (BINDER) 4 WOOD: CELLULOSE HEMICELLULOSES LIGNIN (BINDER) RESINS
More informationInstructables Butcher Block Top
Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.
More informationRuhlmann-style. Poker Table BY F RANK K LAUSZ
Ruhlmann-style Poker Table BY F RANK K LAUSZ Émile-Jacques Ruhlmann was one of the finest designers of the Art Deco period. In the 1920s, he designed and produced many memorable pieces of furniture as
More informationMake your own zero clearance throat plate.
Make your own zero clearance throat plate. A picture tutorial By Wayne Breshears One of the more important table saw accessories you can have is a zero clearance insert or throat plate. The close tolerance
More informationBeds may be put up or taken down quickly by use of a simple bolted connection at rails and uprights. MATERIALS LIST
CANPLY This design has been made both functional and attractive by use of pattern cut-outs in head and foot uprights, which serve as ladders. Since most children love to climb, getting them to bed will
More informationFRIDAY, 27 MAY 9.00 AM AM. Date of birth Day Month Year Scottish candidate number
FOR OFFICIAL USE F 6/4 Q Q2 Q3 Q4 Q5 Q6 Q7 Q8 Total NATIONAL QUALIFICATIONS 2 FRIDAY, 27 MAY 9. AM. AM CRAFT AND DESIGN STANDARD GRADE Foundation Level Fill in these boxes and read what is printed below.
More informationCurved Pieces are a Common Woodworking Challenge
Curved Pieces are a Common Woodworking Challenge I recently created a set of four dining chairs that required three curved back rest pieces each. On the top piece of each chair I wanted to inlay a marquetry
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationBuilding Instructions ARTEMIS Sailing Canoe Workshop and Tools Version 1.0 Brian Pearson / Dr. Axel Schmid Two Sawhorses. Workshop and Tools
Building Instructions ARTEMIS Sailing Canoe Two Sawhorses Workshop Yes, you can build the ARTEMIS sailing canoe in the garage, with good lighting, and assuming a power supply. To have room to work it needs
More informationA candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps.
Activities Discussion These projects allow more skill development including making items to match a drawing, sizing projects to specific dimensions, and just trying fun stuff for the first time! A candle
More informationMachining Laboratory Regulations and Safety
Machining Laboratory Regulations and Safety General Laboratory Regulations Each person using the manufacturing laboratory is expected to comply with the following rules and regulations failure to do so
More informationWorking with Wood and Wood Materials
Working with Wood and Wood Materials Excerpt from the Bosch Encyclopedia of Power Tools. Written & Published by ROBERT BOSCH GmbH and Robert Bosch Tool Corporation. The grain direction of the fibers determines
More informationVCE VET FURNISHING (CABINET MAKING)
Victorian Certificate of Education 2002 SUPERVISOR TO ATTACH PROCESSING LABEL HERE Figures Words STUDENT NUMBER Letter VCE VET FURNISHING (CABINET MAKING) Written examination Friday 1 November 2002 Reading
More informationJOB READY ASSESSMENT BLUEPRINT CABINETMAKING - PILOT. Test Code: 4014 Version: 01
JOB READY ASSESSMENT BLUEPRINT CABINETMAKING - PILOT Test Code: 4014 Version: 01 Specific Competencies and Skills Tested in this Assessment: Safety Apply shop and personal safety rules and procedures,
More information