WHETSTONE SHARPENER MODEL NO: CWS200 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: GC0710

Size: px

Start display at page:

Download "WHETSTONE SHARPENER MODEL NO: CWS200 OPERATION & MAINTENANCE INSTRUCTIONS PART NO: GC0710"

Dennis Barker
6 years ago
Views:

1 WHETSTONE SHARPENER MODEL NO: CWS200 PART NO: OPERATION & MAINTENANCE INSTRUCTIONS GC0710

INTRODUCTION Thank you for purchasing this CLARKE whetstone sharpener. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully.

2 INTRODUCTION Thank you for purchasing this CLARKE whetstone sharpener. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. IMPORTANT Please read all of the safety and operating instructions carefully before using this product. Please pay particular attention to all sections of this User Guide that display warning symbols and notices. WARNING! This is a Warning symbol. This symbol is used throughout the user guide whenever there is a risk of personal injury. Ensure that these warnings are read and understood at all times. CAUTION! This is a Caution symbol. This symbol is used throughout the user guide whenever there is a risk of damaging your product. Ensure that these cautions are read and understood at all times. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. 2

3 GENERAL SAFETY RULES 1) WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY 1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. 2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 3. Do not abuse the cable. Never use it for carrying, pulling or unplugging the power tool. Keep the cable away from heat, oil, sharp edges or moving parts. Damaged or entangled cables increase the risk of electric shock. 4. When operating a power tool outdoors, use an extension cable suitable for outdoor use. Use of a cable suitable for outdoor use reduces the risk of electric shock 5. If operating the power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. 3) PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in personal injury. 2. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 3. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 4. Remove any wrench before turning the power tool on. A wrench left attached to a rotating part may result in personal injury. 5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 3

4 4) POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct accessories for your application. The correct power tool will do the job better and safer at the rate which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 4. Store idle tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate it. Power tools are dangerous in the hands of untrained users. 5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 6. Use the power tool and accessories in accordance with these instructions and in the manner intended, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation. 7. The performance of this tool may vary, depending upon variations in line voltage. Extension cable usage may also affect performance. 5) SERVICE 1. Have your power tool serviced by qualified service personnel using only identical replacement parts. This will ensure that the safety of the power tool is maintained. GRINDER/SHARPENER SAFETY INSTRUCTIONS 1. Ensure the bottom of the grindstone is constantly immersed in water to prevent overheating. 2. Hold the hand tool or blade being sharpered firmly to prevent loss of control. 3. NEVER install a grinding wheel on the polishing side of the machine. Never attempt to install a wire brush, abrasive flap wheel or sanding disc on this grinder. 4. Always replace a cracked grinding wheel immediately. 5. Never use damaged or incorrect grindstones. The stone and bolt were specially designed for your grinder, for optimum performance and safety of operation. Inspect the condition of the grinding stone before use and do not use if any damage is noticed. 6. Do not use aluminium oxide wheels when grinding non-ferrous metals such as aluminium or brass. Use silicon carbide wheels (not included) for grinding non-ferrous metals. 4

5 7. Always use the tool attachments to steady the workpiece. If the tool attachments are not used, the torque of the spinning grinding/polishing wheel may pull the workpiece from your hands. 8. Never leave the grinder unattended when it is connected to an electrical power supply. Switch off the machine and unplug it before leaving. 9. ALWAYS check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tool's operation. A part that is damaged should be properly repaired or replaced at an authorised Service Center. Following this rule will reduce the risk of electric shock, fire or serious injury. 10. Gloves, manufactured to the current European safety standards should be worn when operating grinding equipment. 11. Eye protection manufactured to the current European safety standards should be worn when operating grinding equipment. Note: Bench grinders used in industrial environments may be subject to the requirements of The Provision and Use of Work Equipment regulations 1992 (particularly regarding the training requirement of The Abrasive Wheels Regulations 1970), or other legislation. If in doubt seek advice. Please keep these instructions in a safe place for future reference. 5

6 SAFETY SYMBOLS Not suitable for hand-held cutting off Not suitable for face grinding Wear eye protection Wear protective gloves Read instruction manual before use ENVIRONMENTAL PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment 6

7 ELECTRICAL CONNECTIONS This product is provided with a BS1363 plug fitted with a 5 amp fuse and must be connected to a standard 230 Volt (50Hz) electrical supply, preferably through an approved plug or a suitably fused isolator switch. WARNING! THIS APPLIANCE MUST BE EARTHED IMPORTANT: The wires in the mains lead should be wired in accordance with the following colour code: Green & Yellow - Earth Blue - Neutral Brown - Live If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows: Connect the GREEN & YELLOW coloured wire to the terminal which is marked with a letter E or earth symbol, or coloured GREEN or GREEN & YELLOW. Connect the BROWN coloured wire to the terminal which is marked L or coloured RED. Connect the BLUE coloured wire to the plug terminal which is marked with a letter N or coloured BLACK. If this appliance is found to be fitted with a plug which is moulded onto the electrical cable (i.e. non-rewireable) please note: 1. The plug must be thrown away if it is cut from the electrical cable. There is a danger of electric shock if it is subsequently inserted into an electrical outlet socket. 2. Never use the plug without the fuse cover fitted. 3. Should you wish to replace a detachable fuse carrier,ensure that the correct replacement is used (as indicated by marking or colour code). 4. Replacement fuse covers can be obtained from your local Clarke dealer or any electrical stockist. FUSE RATING The fuse in the plug must be replaced with one of the same rating and this replacement must be ASTA approved to BS1362. We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD). 7

8 OVERVIEW NO DESCRIPTION NO DESCRIPTION 1 ON/OFF Button 5 Honing Wheel 2 Tool Support 6 Tool Support Plate 3 Fixing Knob 7 Grinding Wheel 4 Water Tank 8 Tool Holders (2) 8

BEFORE USE INVENTORY When unpacking, check to ensure that all the parts listed are present. If any are missing or damaged, contact your CLARKE dealer.

Stand the grinder on a flat and sturdy benchtop. 2. Insert the tool support into the two mounting holes at the top of the wet grinder as in Fig 1. Vertical Grinding/Honing 3.

9 BEFORE USE INVENTORY When unpacking, check to ensure that all the parts listed are present. If any are missing or damaged, contact your CLARKE dealer. 1 x Grinder 1 x Stone Grinding Wheel 1 x Water Tank 1 x Tool Support 1 x Tin Abrasive Paste 1 x Angle Guide 3 x Tool Holders (small knives, large knives & straight edges) FITTING THE TOOL SUPPORT 1. Stand the grinder on a flat and sturdy benchtop. 2. Insert the tool support into the two mounting holes at the top of the wet grinder as in Fig 1. Vertical Grinding/Honing 3. Adjust the tool support to the desired height, before tightening the two knobs to secure it in place. Horizontal Grinding 4. Attach the tool support by inserting into the two mounting holes located on the rear side of the grinder. Adjust to the desired height, before tightening the two knobs to secure it as in Fig Plug the machine into the nearest power supply. 9

10 6. Install the water tank beneath the grinding stone. Fill the water tank with clean water up to the fill line indicated on the tank as in Fig 3. During operation,the grinding stone will become saturated with water. Ensure the water tank is re-filled when necessary and discard any excess particles of stone which have accumulated in the water tank. 7. To start/stop the grinder press the ON/OFF buttons. 8. Run the grinder and apply a light coating of machine oil to the leather honing wheel. Next, distribute the abrasive paste, evenly onto the honing wheel with a stick or suitable tool as in Fig 5. This should be sufficient for five to ten tool honing operations. This process should be repeated as required to ensure the long life of the honing wheel and achieve a good finish. 10

USING YOUR GRINDER WARNING: FRAGMENTS FROM A BROKEN/DETACHED GRINDING WHEEL CAN CAUSE SERIOUS INJURY. WARNING: WHEN USING THE GRINDING WHEEL, DO NOT STAND DIRECTLY IN LINE WITH THE ROTATING WHEEL.

WARNING: WHEN GRINDING, KEEP THE TOOL BLADE STRAIGHT TO PREVENT SNATCHING OR JAMMING. WARNING: THE STONE WILL CONTINUE TO ROTATE FOR A FEW SECONDS AFTER THE SWITCH HAS BEEN PRESSED. GETTING STARTED 1.

11 USING YOUR GRINDER WARNING: FRAGMENTS FROM A BROKEN/DETACHED GRINDING WHEEL CAN CAUSE SERIOUS INJURY. WARNING: WHEN USING THE GRINDING WHEEL, DO NOT STAND DIRECTLY IN LINE WITH THE ROTATING WHEEL. WARNING: ENSURE THAT THE WORKING POSITION ADOPTED DOES NOT CAUSE OPERATOR FATIGUE WHICH MAY LEAD TO LOSS OF CONTROL OF THE TOOL BEING GROUND. WARNING: WHEN GRINDING, KEEP THE TOOL BLADE STRAIGHT TO PREVENT SNATCHING OR JAMMING. WARNING: THE STONE WILL CONTINUE TO ROTATE FOR A FEW SECONDS AFTER THE SWITCH HAS BEEN PRESSED. GETTING STARTED 1. Slide the support plate onto the tool support. Position the support plate directly above the grinding stone or honing wheel. Loosen the two knobs, on the support plate. Insert the tool blade (sharp end downwards) in the support plate, then firmly tighten the tool blade in place as in Fig Adjust the tool support so that the support plate is approximately 1-2mm from the grinding stone or honing wheel. Loosen the two knobs on the support plate to adjust the tool blade so that its sharp edge lightly touches the grinding stone or honing wheel. 3. Turn on the grinder and slowly move the support plate back and forth along the tool support to grind the tool blade. If necessary, loosen the two knobs on the support plate to re-adjust the tool blade. 11

Set the holder on the tool support and adjust the tool support downward so that the knife blade lightly touches the grinding stone or honing wheel, then temporarily remove the holder from the tool

12 GRINDING/HONING A SMALL KNIFE BLADE 1. Loosen the two knurled screws on the holder. Centre the tension plate along the top edge of the knife blade then firmly tighten the two knurled screws to secure the knife blade in position as in Fig Set the holder on the tool support and adjust the tool support downward so that the knife blade lightly touches the grinding stone or honing wheel, then temporarily remove the holder from the tool support. 3. Turn on the grinder and grip the holder firmly. Place the holder on the tool support and slowly move the holder back and forth along the tool support to grind/hone the knife blade. USING THE ANGLE GUIDE 1. The angle guide is used to determine the cutting edge angle of a tool. To do so, clamp the tool into the support plate, then install the support plate on the tool support as shown in Fig Hold the angle guide with the desired angle (as indicated on the angle guide) at the tool tip. 3. Adjust the height of the tool support so that the front end of the angle guide, touches the grinding stone. Make sure the angle guide continues to touch the tool tip. 4. Once the desired angle is achieved, firmly lock the tool support in place and remove the angle guide. GRINDING TIPS After setting the angle, turn on the grinder and begin grinding process. Press the tool evenly onto the grinding stone near the cutting edge, and move the tool crosswise across the stone. Make sure that at least half the width of the cutting edge comes into contact with the grinding stone at any time, to avoid damage to the stone. 12

Allow the grinding stone to do the cutting. Do not apply excessive downward pressure on the tool when grinding. Make sure the level of water in the tank is adequate. Never attempt to dry grind.

13 Allow the grinding stone to do the cutting. Do not apply excessive downward pressure on the tool when grinding. Make sure the level of water in the tank is adequate. Never attempt to dry grind. When finished, turn the machine off and wait until it has completely stopped before unplugging from the power supply. Then remove the tool. HONING TIPS Never hone against the direction of the honing wheel, which would cause the tool to cut into the leather honing wheel surface. Although you can work freehand for the honing process, you will achieve more precise results by securing the tool with the support plate or holder, and setting the honing angle to the angle used when grinding the tool. Press the tool evenly onto the honing wheel near the cutting edge, and move the tool crosswise across the wheel. Ensure that at least half the width of the cutting edge comes into contact with the wheel at any time to avoid damage to the wheel. Allow the wheel to do the honing, without applying excessive downward pressure on the tool. Always ensure the honing wheel is kept saturated with machine oil and abrasive paste for best results. When finished, turn off the machine and ensure it has completely stopped before removing the tool. 13

DRESSING A NEW STONE New grinding stones are frequently not true and in time can become grooved, glazed (built-up), out of round or otherwise mis-shapen.

14 MAINTENANCE INSTALLING A NEW GRINDING STONE 1. Unscrew and remove the nut, and washer that secures the stone in place. 2. Remove the old grinding stone and install the replacement, securing it with the nut and washer. Grasp the honing wheel to prevent the drive shaft from turning while tightening the nut. DRESSING A NEW STONE New grinding stones are frequently not true and in time can become grooved, glazed (built-up), out of round or otherwise mis-shapen. To correct these defects, a grinding stone dresser is required. This is available from your Clarke dealer. ET125 Grinding Wheel Dressser,- Part No: Replacement Dresser Wheel,- Part No: ET154 1/2 Carat Diamond Tip Wheel Dresser,- part No: If the grinding stone is new, allow it to spin for a minute with no load. Check that it is spinning straight and true. If not, it will require dressing before use. 2. Stand to the side of the grinding stone and hold the dresser handle firmly. Place the dresser on the tool support so that its wheels can move freely (i.e, the exposed part of the wheel should be facing up). Run the grinding stone at full speed and apply the dresser to the surface of the grindstone. INSTALLING A NEW HONING WHEEL 1. Unscrew and remove the nut and washer that secures the wheel in place. 2. Remove the old honing wheel and install the replacement, securing it with the nut and washer. Ensure the drive pin, rests in the groove in the hidden face of the wheel. 14

15 GENERAL MAINTENANCE Make sure that all nuts, bolts and screws are tight and secure. Occasionally apply a little light oil to the shaft supporting bush. Always have any damaged or worn parts repaired or replaced by qualified service personnel. Do not attempt to repair the grinder unless you are qualified to do so. CLEANING & STORAGE To maintain the best possible performance from your grinder it should be kept clean. Clean the exterior of the machine using a mild detergent or mild solvent. Never immerse the machine in liquid. To reduce fire hazard, keep the cooling vents & motor fins free of debris. Store the grinder in a clean, dry location, out of reach of children. TROUBLESHOOTING PROBLEM CAUSE SOLUTION Grinder will not operate. Motor runs but wheel not spinning. No power supply. ON/OFF switch is faulty. Fuse blown. Motor faullty. Retaining nut not tight. Honing wheel not engaged with drive pin. Motor drive shaft slipping on drive wheel. Check supply & rectify. Consult your CLARKE dealer. Check & replace if necessary. Consult your dealer if condition persists. Consult your CLARKE dealer. Ensure wheel is correctly seated. Tighten retaining nut. Loosen wheel & engage wheel on drive pin. Clean spiggot & drive wheel surface Motor gets too hot. Wrong supply voltage. Ensure supply voltage is correct. Work load too heavy. Reduce pressure applied to workpiece. Unusual vivration while working. Grindstone mounted incorrectly or damaged. Bearings badly worn. Check & rectify. Replace grinding wheel immediately. Consult your CLARKE dealer. 15

16 SPECIFICATIONS Product Dimensions (L x W x H) Weight Grinding StoneDimensions (D x T) Honing Wheel Dimensions (D x T) Stone type Rated Voltage / Frequency Motor Wattage Input Ampere (typical load) No Load Speed Duty Cycle Classification Sound pressure Sound Power Measured (Lwa db) 330 x 280 x 275 mm 9.7 kg 200 x 40 mm 200 x 30 mm K V / 50 Hz 120 W 0.43 A 113 rpm S1 (continuous) 78.5 db(a) 91.5 Lp A 16

17 EXPLODED DIAGRAM & PARTS LIST 17

18 EXPLODED DIAGRAM & PARTS LIST No Description 1 Holder Assembly 2 Knurled Screw 3 Washer 4 Spring 5 Centre Tension Plate 6 Holder Arm 7 Guard 8 Wing-nut 9 Handle 10 Tool Support Assy 11 Pivot bush 12 Spring 13 Tool Plate 14 Washer 15 Adjusting Knob 16 Support Plate 17 Nut 18 Penny Washer 19 Grinding Stone 20 Supporting Bush 21 Adjusting Knob 22 Locking Collar 23 Tool Support 24 Friction Drive Wheel 25 Washer 26 Retaining Knob 27 Honing Wheel 28 Drive Shaft 29 Roll Pin (short) 30 Roll Pin (long) 31 Washer No Description 32 Main Housing 33 Self-tapping Screw 34 ON/OFF Pushbuttons 35 Cable and Plug 36 Junction Box 37 Capacitor 38 Drive Motor 39 Plastic Foot 40 Screw 41 Water Tank 42 Angle Guide 43 Abrasive Paste 44 Nut 45 Mounting Bracket 46 Mounting Rod 47 Washer 48 Spring 49 Nut 50 Washer 51 Bolt 52 Spacer For spare parts for this product, please quote part numbers DDCWS to 52 as applicable. Only items in bold text will normally be available as over the counter spares. 18

19 DECLARATION OF CONFORMITY 19

MINI RECIPROCATING SAW MODEL NO: CRS350M

CRS350M - Mini Reciprocating saw.fm Page 1 Thursday, November 22, 2012 9:41 AM MINI RECIPROCATING SAW MODEL NO: CRS350M PART NO: 6462550 OPERATION & MAINTENANCE INSTRUCTIONS LS1112 CRS350M - Mini Reciprocating