Steel Reinforced Joining Guide (Horizontal / Vertical)
|
|
- Bertha Warner
- 5 years ago
- Views:
Transcription
1 (Horizontal / Vertical) for Andersen Patio Door and/or Elliptical Top Window Combinations Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits of your Andersen product are to be fully attained. Therefore, please read and follow this instruction guide completely. If your abilities do not match this procedure s requirements, contact an experienced contractor. You may direct any questions about this or other products to your local Andersen dealer, found in the Yellow Pages under Windows or call Andersen WindowCare service center at Monday through Friday, 7 a.m. to 7 p.m. Central Time and Saturday, 8 a.m. to 4 p.m. Central Time. Thank you for choosing Andersen. Every assembly and installation is different (windloads, structural support, etc.). Andersen strongly recommends consultation with an Andersen supplier or an experienced contractor, architect, or structural engineer prior to the assembly and installation of any Andersen product. For installation methods not covered in this guide, (i.e. through jamb) please visit the Architect Detail File on the web ( Andersen has no responsibility in regard to the post-manufactured assembly and installation of Andersen products. Use caution when working at elevated heights and around unit openings. Follow manufacturer s instructions for safe use of ladder and/or scaffolding. Failure to do so may result in injury or death. Follow manufacturer s instructions for safe operation of hand/power tools. Always wear safety glasses. Failure to do so may result in injury and/ or product damage. Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage. Unless specifically ordered, Andersen windows and doors are not equipped with safety glass, and if broken, could fragment causing injury. Many laws and building codes require safety glass in locations adjacent to or near doors. Andersen windows are available with safety glass that may reduce the likelihood of injury when broken. Information on safety glass is available from your local Andersen dealer. Andersen Installation Flanges DO NOT take the place of standard window and door flashing. Unit must be properly flashed and sealed with sealant, and full width drip cap for protection against water and air infiltration. Use non-reflective flashings. Highly reflective flashing tapes can raise the surface temperature of the vinyl to the point where vinyl deformation and product damage may occur. Do not apply any type of film to glass. Thermal stress conditions resulting in glass damage could occur. Use of movable insulating materials such as window coverings, shutters, and other shading devices may damage glass and/or vinyl. In addition, excessive condensation may result causing deterioration of windows and doors. Andersen and all other marks where denoted are trademarks of Andersen Corporation Andersen Corporation. All rights reserved BB Revised 12/27/07
2 Parts included (2) Steel Gusset Plates (16) No.7 x 5/8" Screws (8) No.10 x 2" Screws (18) No.10 x 2-1/4" Screws (pack # RMA2) (18) No.10 x 2-1/2" Screws (pack #RMB2) (18) No.10 x 2-3/4" Screws (pack #RMC2) (10) Location Blocks (11) Trim Strip Clips for 96" Length (Casement and Awning Units Only) (16) Trim Strip Clips for 150" Length (Casement and Awning Units Only) Other Andersen Parts Needed for Complete Installation Steel Joining Strip with End Brackets* Exterior Trim Strip* Inside Wood Casing* Interior Extension Jamb Inside Wood Casing* Available in 2-3/8", 2-5/8" and 2-7/8" widths in both 96" and 144" lengths. Location Block Steel Gusset Plate Screws Installation Tools Needed Safety Glasses Tape measure Saw for cutting steel Phillips head screwdriver Pencil Caulk Gun Sealant Hammer 8d Nails or #6 or Larger Screws Drill 1/8" Drill Bit 3/32" Drill Bit Carpenter's square Rust Inhibiting Primer Wood Block Filler Strip Clamps Additional Parts Required (Sold Separately) Drip Cap (full width) Steel Joining Strip* Available in 8' 0-1/4", 9' 6" and 12' 6" lengths. End Bracket* Exterior Trim Strips* Available in 96" and 150" lengths. Trim Strips Clips (Casement and Awning Units Only) * These parts are needed for a complete reinforced joining installation. They are not included in the steel gusset plate kit and must be purchased separately. Horizontal Exterior Trim Strip Metal fasteners and components may corrode when exposed to preservative-treated and/or fire-retardant treated lumber. Obtain and use the appropriate metal fasteners and hardware as called out by the installation guide to fasten unit to any rough opening made from preservative-treated and fire-retardant treated lumber. Failure to use the appropriate materials for the installation may cause a failure resulting in injury, property or product damage. The Andersen Reinforced Steel Non-Reinforced Joining products are designed to give added windload performance to joined combinations of Andersen windows and patio doors. They do not take the place of structural components in a building. Failure to provide adequate structural support could lead to window and door performance problems. Window units joined over patio doors should not rest on the door's head jamb. Units may be completed horizontally and then lifted into the rough opening, or mulled in sections and assembled in the rough opening. The method used will depend on the combination size and weight, and on the installer's individual preferences. 2
3 VERIFY YOUR SELECTION Andersen offers several choices in custom designed joining materials. Whether or not to use reinforcement PUSH PUSH in a combination is dependent on the combination size and the design load requirement. The combination size is based on the geometry and area of the combination in question. Design load is based on several factors; wind speed, location, orientation, elevation, and others. Local building codes should be consulted for determining the design load of your installation. Determination of the design load is the sole responsibility of the architect, building PULL PULL owner, contractor and/or consumer. Proper joining material selection for Andersen windows and patio doors is essential if the benefits of experienced window design and engineering, quality materials and skilled workmanship are to be fully attained. Since every installation is different, these joining material selection, assembly and installation instructions are guidelines only. Andersen strongly recommends consultation with the local Andersen supplier or an experienced contractor, architect, or structural engineer prior to the installation of any Andersen product. 1. Verify that Steel Joining is Adequate for Your Installation Calculate the average adjacent unit dimension (A+B 2). Determine the mullion length (C). Use the windload chart below to cross reference the average adjacent unit dimension with the mullion length to determine the windload performance of your combination. Be sure that this performance is adequate for your installation requirements. Refer to the Combination Design section in the Andersen Product Guide for further information. Design Windload PSF Table for Narrow Reinforced Steel Type of Combination: 1-Way or 2-Way For Combining: Andersen Patio Doors with Andersen Windows Average Adjacent Unit Dimension A + B 2 = 12' 6" A + B 2 = 12' 1" A + B 2 = 11' 6" A + B 2 = 11' 1" A + B 2 = 10' 6" A + B 2 = 10' 1" A + B 2 = 9' 6" A + B 2 = 9' 1" PSF A + B 2 = 8' 6" A + B 2 = 8' 1" A + B 2 = 7' 6" A + B 2 = 7' 1" A + B 2 = 6' 6" A + B 2 = 6' 1" A + B 2 = 5' 6" A + B 2 = 5' 1" A + B 2 = 4' 6" A + B 2 = 4' 1" A + B 2 = 3' 6" A + B 2 = 3' 1" A + B 2 = 2' 6" A + B 2 = 2' 1" C = (mullion length) 5' 6" or less 6' 1" 6' 6" 7' 1" 7' 6" 8' 1" 8' 6" 9' 1" 9' 6" 10' 1" 10' 6" 11' 1" 11' 6" 12' 1" 12' 6" Single transom row horizontal reinforcement When using a single row of transom units over doors, make sure that the units are securely fastened to the adjacent framing. This prevents the units' weight from transferring to the door head jamb. Header structure required above 4-panel gliding doors 3
4 2. Prepare Units Assemble Gliding Door frame(s) if applicable. Refer to unit installation guide. Position units on a clean flat work surface with the units' exterior facing up. Remove all packaging materials. Identify the locations for the Steel Reinforced Mullion/Transom Joints. All joins not requiring the Steel Reinforced Mullion must use standard non-reinforced wood joining strips (assembled first) and follow Andersen's Narrow Joining procedures. Measure 7/8" down from exterior edge of frame on Casement, Awning, Circle Top, or Elliptical Top units and cut Installation Flanges on the jambs to be joined with the Steel Reinforced Joining Strip (see Figure 1). On Flexiframe units or Patio Doors, remove the Installation Flanges on the jambs to be assembled with the Steel Joining Strip (see figure 2). Figure 1 Casement, Awning, Circle Top, or Elliptical Top Units Figure 2 Utility Knife Exterior Sides Up Installation Flanges must overlap one another to the exterior at the ends of the mullion/transom joints. Flip units over so exterior sides are down. Flexiframe Units or Patio Doors 3. Cut and Install Steel Joining Strip Cut the Steel Joining Strip to the length equal to the overall combined unit dimension length. If side light windows are used with a door, the steel plate can run the full length of the door jamb, or it can be cut to the length of the window jamb(s), depending on how the rough opening is framed. Cutting can be accomplished with any standard metal cutting method (hacksaw, reciprocating saw, band saw, circular saw with metal cutting blade). Gusset Plate Window Treat the cut ends and drilled holes on the Steel Joining Strip with a quality rust inhibiting primer. Failure to do so may promote premature corrosion, which could result in structural failure. Patio Door Window Steel Joining Strip Steel Joining Strip Gusset Plate bent 90 Units are shown installed for example only. 4
5 ASSEMBLY 4. Select Proper Screw Pack Envelope Select the proper screw pack envelope based on the units and the direction of the reinforced joint in your combination. For Joining These Units: In This Joining Direction: Use Screw Size: Screw Pack Gliding Door to Casement Vertical 2-1/4" RMA2 Gliding Door to Awning Horizontal 2-1/4" RMA2 Hinged Door to Casement Vertical 2-1/4" RMA2 Hinged Door to Awning Horizontal 2-1/4" RMA2 Gliding Door to Awning Vertical 2-1/2" RMB2 Gliding Door to Casement Horizontal 2-1/2" RMB2 Hinged Door to Casement Horizontal 2-1/2" RMB2 Hinged Door to Awning Vertical 2-1/2" RMB2 Gliding Door to Circle Top Horizontal 2-1/2" RMB2 Gliding Door to Elliptical Top Horizontal 2-1/2" RMB2 Hinged Door to Flexiframe Vertical/Horizontal 2-1/2" RMB2 Hinged Door to Circle Top Horizontal 2-1/2" RMB2 Awning to Circle Top Horizontal 2-1/2" RMB2 Gliding Door to Flexiframe Vertical/Horizontal 2-3/4" RMC2 Hinged Door to Elliptical Top Horizontal 2-3/4" RMC2 Casement to Elliptical Top Horizontal 2-3/4" RMC2 Flexiframe to Elliptical Top Horizontal 2-3/4" RMC2 5. Choose Reference Detail Refer to one of the details on pages 4 through 7 that illustrates the reinforced join in your combination. Awning to Gliding Door- Horizontal Join Awning to Hinged Door- Horizontal Join* or Casement to Hinged Door- Vertical Join 5
6 Casement to Gliding Door- Vertical Join Elliptical to Gliding Door- Horizontal Join Exterior Casement to Gliding Door- Horizontal Join Elliptical to Awning - Horizontal Join Circle Top Window to Gliding Door - Horizontal Join 6
7 Awning to Gliding Door- Vertical Join Casement to Frenchwood Hinged Door- Horizontal Join* or Awning to Frenchwood Hinged Door- Vertical Join Flexiframe Window to Gliding Door - Horizontal or Vertical Join Flexiframe Window to Frenchwood Hinged Door - Horizontal* or Vertical Join Elliptical to Frenchwood Hinged Door - Horizontal Join Elliptical to Casement - Horizontal Join 7
8 Flexiframe Window to Gliding Door - Horizontal Join Elliptical to Flexiframe Window - Horizontal Join 6. Assemble the Combination The Side Stop on the lock side of tandem lock Casement units has an underlying lock mechanism. Use caution when removing Side Stop on the Lock side to avoid damage to lock mechanism and/or Side Stop. Remove the inside stops from the jambs to be joined, if necessary. Position the steel joining strip between the jambs, with scribe marks facing the interior, centering the steel joining strip from each end. Clamp the jambs together firmly. For AP/PA horizontal joining, a 1/8" spacer is required, notched for flush bolt, between the steel plate and the head jamb. Drill 1/8" pilot holes, alternating sides, at 8" intervals, using scribe marks as hole locations. Drive the appropriate length screws through the pilot holes. Replace the inside stops and turn the combination over so that the exterior side is up. 7. Prepare Exterior Trim Strip(s) If combination has vertical and horizontal joins, Vertical Exterior Trim Strips must run continuously and should be applied first. Fill voids at intersections with silicone sealant and butt Horizontal Trim Strips tightly against Vertical Trim Strips. Failure to do so may allow water infiltration leading to product damage. Trim Strip Clip Locations for Casement and Awning Units Measure and cut Exterior Trim Strip(s) to length. Make sure that both the unit and the Exterior Trim Strip contact surfaces are clean. Apply a generous bead of sealant to both sides of the trim strip. If combination includes Casement and/or Awning units apply Trim Strip Clips to Exterior Trim Strip. Locate Trim Strip Clips 1" from each end, and another 6" from each end. Space remaining clips at 12" intervals. Sealant (Full Length) Trim Strip Clip (Casement and Awning Only) 8
9 8. Apply Exterior Trim Strip(s) Position Exterior Trim Strip in combination making sure both ends are flush with end of units. Using a hammer and wood block tap the Exterior Trim Strip until firmly seated. Clean off any excess sealant squeeze out immediately. Exterior Trim Strip Hammer and Wood Block Exterior Sides Up 9. Apply Sealant Apply sealant to completely fill void between joined units. Ends of Trim Strip Sealant Caulk Gun Exterior Sides Up 10. Apply Gusset Plates Predrill using a 3/32" drill bit and attach the Gusset Plates to the unit on both ends of the steel joining strip with eight #7 x 5/8" Gusset Plates Screws provided. #7 x 5/8" Gusset Plate 9
10 11. Install Combination in Rough Opening Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage. Gusset Plate Metal fasteners and components may corrode when exposed to preservative-treated and/or fire-retardant treated lumber. Obtain and use the appropriate metal fasteners and hardware as called out by the installation guide to fasten unit to any rough opening made from preservative-treated and fire-retardant treated lumber. Failure to use the appropriate materials for the installation may cause a failure resulting in injury, property or product damage. Drill Position the combination in the rough opening. Use shims as needed around the perimeter units to square and level the combination. Recheck for plumb, level and square, measurements must be within 1/8". Attach combination by fastening through installation flanges. Shim and screw through the perimeter jambs into the framing every 12" to 16" where possible with extra screws provided. Attach each Gusset Plate to the framing material with a minimum of three 8d nails or No. 6 or larger screws. Shim each Gusset Plate as necessary to maintain a proper fit in the rough opening. Seal all the areas around the Gusset Plate and installation flanges with sealant. Proceed to full width drip cap application step in unit installation guide for full width drip cap, flashing and insulation steps. 10
Steel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More informationNon-Reinforced Joining Guide (Horizontal/Vertical)
Non-Reinforced Joining Guide (Horizontal/Vertical) for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationNon-Reinforced Joining Guide (1-Way Vertical or Horizontal) for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products
(1-Way Vertical or Horizontal) for Andersen 200 Series Tilt-Wash Double-Hung Windows and Complementary Products Non-Reinforced Joining Guide Congratulations! You have just purchased one of the many fine
More informationNon-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows
(2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly,
More informationfor Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window
for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.
More informationfor Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms
for Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen Frenchwood Patio Door Sidelights and Transoms
for Andersen Frenchwood Patio Door Sidelights and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More informationPanel Assembly and Installation
Assembly and Installation Assembly and Installation for Andersen 400 Series Frenchwood, 200 Series Narroline, 200 Series Perma-Shield Gliding Patio Doors and 400 Series Perma-Shield Gliding Patio Doors
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows
for Andersen 400 Series Tilt-Wash Transom and 200 Series Narroline Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide. for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass)
for Andersen 400 Series Tilt-Wash Picture Windows with Stormwatch Protection (High-Performance Impact Resistant Glass) Installation Guide Congratulations! You have just purchased one of the many fine Andersen
More informationInstallation Guide for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows
for Andersen 200 Series Tilt-Wash Picture, Transom and Circle Top Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationSash Replacement Guide for Andersen Impact Resistant Casement Windows
Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationTransom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door
Transom Joining for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door INSTALLER: Please leave this guide with the building owner to file for future reference. Congratulations! You have just
More informationInstallation Guide for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006
for Andersen 400 Series Tilt-Wash Transom Windows with Stormwatch Protection (PG Upgrade) Manufactured After 2006 Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More information1-Way Vertical Joining (Pages 2-22) 1-Way Horizontal Joining (Pages 23-44)
3/4" LVL Reinforced Joining Guide (1-Way Vertical Joining) or (1-Way Horizontal Joining) 3/4" LVL Reinforced Joining Guide (1-Way Vertical Joining) or (1-Way Horizontal Joining) for Andersen 400 Series
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationInstallation Guide for Andersen Architectural Clad Awning Windows
Guide for Andersen Architectural Clad Awning Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More informationInstallation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors
Installation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen 400 Series Gliding Windows
for Andersen 400 Series Gliding Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits of your
More informationInstallation Guide for Andersen Architectural Clad Hinged Windows
Guide for Andersen Architectural Clad Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the
More information3/4" LVL Reinforced Joining Guide
(2-Way Horizontal and Vertical Joining) for Andersen 400 Series Tilt-Wash Double-Hung, Picture, and Transom Windows with Stormwatch Protection Congratulations! You have just purchased one of the many fine
More informationRead guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Installation Guide for E-Series/Eagle High-Performance Mullion Windows with LVL Reinforcement and Installed Using Type B Clips Thank you for choosing Andersen. Instructions are for typical, new wood-framed
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationInstallation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows
Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read
More informationReinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows
Reinforced 10 Bow Window Assembly and Installation Guide for Andersen 400 Series Transom Joined Casement Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction
More informationSash Replacement Guide for Andersen 400 Series Tilt-Wash Transom Windows
for Andersen 400 Series Tilt-Wash Transom Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen
More informationReglazing Guide for Andersen 400 Series Specialty Windows with Stormwatch Protection (High-Performance Impact Resistant Glass)
Reglazing Guide for Andersen 400 Series Specialty Windows with Stormwatch Protection (High-Performance Impact Resistant Glass) INSTALLER: This reglazing procedure is to be performed only by a professional
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationInstallation Guide for E-Series/Eagle Clad Mechanically Fastened Windows
Guide for E-Series/Eagle Clad Mechanically Fastened Windows Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Clad Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationInstallation Guidelines. Next Dimension. Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window
Installation Guidelines Next Dimension Single Hung / Single Hung Fixed / Double Hung / Sliding Window / Fixed Window Windsor Windows & Doors Windsor Windows & Doors 900 S. 19 th St. 2210 Stafford St. Extn
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Wood Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationStationary Panel Replacement
Stationary Panel Replacement Product Series: 200 Series Product Type: Hinged Inswing Patio Doors Read these instructions before starting procedure. For additional information visit www.andersenwindows.com.
More informationTools required by installer: Materials required by installer:
Installation Guidelines For Quaker Window Products Vinyl product line (Single Hung, Double Hung, Sliding Window, Fixed Window, Casement, Awning, and Hopper) Installer: Read these instructions completely
More informationReplacement Guide. For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System RECOMMENDED TOOLS:
Replacement Guide For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System IMPORTANT: READ ENTIRE GUIDE BEFORE BEGINNING INSTALLATION. PLEASE NOTE: Proper assembly, installation
More informationInstallation Instructions for E-Series 2 or 4-Panel Gliding and French Gliding Patio Doors
Installation Instructions for E-Series 2 or 4-Panel Gliding and French Gliding Patio Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More informationFollow instructions from foam, sealant and flashing manufacturer regarding material application and compatibility with this product.
Installation Guide for Andersen Wood Outswing Folding Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationInstallation Guidelines for all Quaker products with nail fins New Construction nail fin installation with a Zip sheathing system.
www.quakerwindows.com www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines for all Quaker products with nail fins New
More informationInstallation Guide for E-Series/Eagle Ascent 2 or 4 Panel Gliding (Sliding) Patio Doors
Installation Guide for E-Series/Eagle Ascent 2 or 4 Panel Gliding (Sliding) Patio Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More information26- H i n g e d P a t i o D o o r s - I n s w i n g
Contents Hinged Patio Doors - Inswing Basic Unit Details... 2 Options / Accessories Accessibility Option... 5 Andersen Grilles... 6 Extension s... 7 Anchoring Methods... 8 Joining Details... 9 Suggested
More informationINSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationINSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS.
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the owner. Please read
More informationF r e n c h w o o d G l i d i n g P a t i o D o o r s
Contents Frenchwood Gliding Patio Doors Basic Unit Details Two and Four Panel...9-2 Sidelight...9-5 Options / Accessories Ramped Insert - Interior and Exterior...9-6 Grilles...9-7 Anchoring Methods...9-9
More informationInstallation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit.
Installation Guidelines For Quaker Window Products Aluminum flange fin sub sill & receptor system using a T mulled twin window unit. Installer: Read these instructions completely before starting any installation.
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationAssembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame
Assembled Patio Door Installation Guide 2-Panel Patio Door with Non-Welded Frame americancraftsmanwindows.com American Craftsman and all other marks where denoted are trademarks of Andersen Corporation
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationFixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows
Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows Manufactured Between September 2005 and October 2006 Read all instructions carefully before attempting
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationRetractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)
Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents
More informationGrand Garden Chalet 6X3 Assembly Manual
Revision #11 June 15, 2010 Grand Garden Chalet 6X3 Assembly Manual Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety Eyewear
More informationSash and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows
and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows Please read this guide completely before starting. For questions about this and other Andersen products, call 1-888-888-7020.
More informationINSTALLATION INSTRUCTIONS for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII032)
for Wood Bay or Bow Windows with Nailing Fin or Exterior Trim (JII0) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for wood and clad wood bay
More informationSash may be heavy. Use a reasonable number of people with sufficient strength to lift, carry, remove and install. Tape broken glass with duct tape bef
Improper re-glazing product (s) can affect the performance under stress and may contribute to property damage or injury in high wind conditions. The installer should not proceed with re-glazing if these
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationWindow with Nail fin (New construction)
Window with Nail fin (New construction) Disclaimer: Improper installation and care may void warranty. These instructions are a basic/general recommendation for installation, but may not be utilized in
More informationPassive Panel Replacement
Passive Panel Replacement Product Series: 200 Series Product Type: Hinged Inswing Patio Doors Read these instructions before starting procedure. For additional information visit www.andersenwindows.com.
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationInstallation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
www.quakerwindows.comv www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines For ALUMINUM M-SERIES 3 PANEL SLIDING DOOR
More informationTHERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE)
THERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE) fig.3 Casement, Awning, Fixed Casement, Direct-Set, Double-Hung, Single-Hung & Horizontal Slider Windows Materials
More informationGrand Garden Chalet 6X3 Assembly Manual - Costco
Revision #16 March 22nd, 2013 Grand Garden Chalet 6X3 Assembly Manual - Costco Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use
More informationAll Window Installation Instruction
1 All Window Installation Instruction Hurd Window Installation Instructions for Nail Fin & Wood Brick Mould Units Nail Fin Windows See Pages 2-11 Wood Brick Mould Windows See Pages 2-6, 8 & 12BM - 14BM
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español
More informationGrand Garden Chalet 6X3 Assembly Manual
Revision #8 November 1, 2009 Grand Garden Chalet 6X3 Assembly Manual Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety
More informationPassive Panel Replacement Guide
Replacement Guide for Andersen 200 Series d Patio Doors - Inswing For questions call 1-888-888-7020. For more information and/or guides visit andersenwindows.com. Please leave this guide with building
More informationDOOR INSTALLATION GUIDE WOOD FRAMING New Construction
DOOR INSTALLATION GUIDE WOOD FRAMING New Construction IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing doors. Any local building code requirements supersede
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS
WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems
More informationGarden Chalet 4X2 Assembly Manual
Revision #6 April 12th, 2010 Garden Chalet 4X2 Assembly Manual Thank you for purchasing a 4x2 Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use Safety Eyewear
More informationI n s t a l l a t i o n I n s t r u c t i o n s
HInged PAtio Door Systems I n s t a l l a t i o n I n s t r u c t i o n s IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation.
More informationwindow installation Guide wood FRaMinG New Construction
window installation Guide wood FRaMinG New Construction IMPORTANT NOTICES AND INFORMATION Read these instructions in their entirety prior to installing windows. Any local building code requirements supersede
More informationHR175 Sash Replacement Kit Installation Instructions
HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows with Exterior Trim or Nail Fin (JII024)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows with nailing fin or primed wood windows with exterior trim. While the
More information6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015
6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015 Thank you for purchasing a 6x6 Maximizer Storage Shed. Please take the time to identify all the parts prior to assembly. Please Note-
More informationAluminum Clad Wood Window Field Mulling and Stacking Instructions
Aluminum Clad Wood Window Field Mulling and Stacking Instructions Mulling Stacking Mulling and Stacking IMPORTANT: Please read before you begin. TABLE OF CONTENTS AND TOOL / MATERIAL REQUIREMENTS START
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More informationSiding Components. Installation Guide
Siding Components Installation Guide 2016 MID-AMERICA SIDING COMPONENTS INSTALLATION GUIDE This guide will show you the products of the Mid-America Siding Components family. It provides specific installation
More informationSun Windows General Information New Construction Sliding Door Installation Instructions H F
A G B D C H F H E H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationINSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO
2008 Pella Corporation Part Number: 801V0101 INSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE
More informationFRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274
FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION
More informationInstallation Guide 2016
Installation Guide 2016 BUILDERS EDGE INSTALLATION GUIDE This guide will show you the products of the Builders Edge family. It provides specific installation steps and application details. Our main goal
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation
More informationCurtain Wall Installation Guide
Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation
More informationC-Series & S-Series Classic Frame with Transom (Single or Pair)
1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More information6X3 Patio Garden Shed Assembly Manual
Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More information