Section 1 Cubicles. Section 2 IPS Duct Panel Systems. Section 3 - Vanity Units Components & Assembly 12. Section 4 Basic Maintenance.
|
|
- Stuart Simmons
- 5 years ago
- Views:
Transcription
1
2 Contents Section 1 Cubicles Cubicle Components 3 Cubicle Installation 4-5 Cubicle Fittings Brackets 6 Hinges 7 Partition Support Leg 8 Indicator Bolt 9 Section 2 IPS Duct Panel Systems Frame, Flash & Panel Assembly 10 IPS Standard Configurations 11 Section 3 - Vanity Units Components & Assembly 12 Section 4 Basic Maintenance 13 Page 2
3 Section 1 Cubicles Cubicle Components Page 3
4 Fix Brackets to wall along the line Align & position Partition to brackets. Temporarily support Partition whilst doing so Mark vertical line on rear wall 3. Level across the top of the channel brackets to the position of the next cubicle channel brackets, mark and fix to the rear wall. (This ensures that the cubicles are all level even if the floor is not). Repeat for all remaining channel brackets to be fixed to the rear wall. Mid Pilaster 4. Position the partition(s) into the channel brackets on the rear wall, whilst providing temporary support, and level as necessary. The partitions should be set up 150mm off the floor. 5. Fix three channel brackets to the centre line of the Mid Pilaster(s), and where cubicles are in a corner, three Angle Brackets to the outer edge of the End Pilaster 6. Next check the squareness of the partition and then fit the Partition Support Leg(s) to bottom of the partition(s) approximately 100mm from the front edge. (please ensure before drilling that no under floor heating is present). 7. Position the Mid Pilaster(s) to the end of the partition, and push-fit the channel brackets over the 'open' end of the partition(s) ensuring the pilaster and partition tops are aligned. Page 4
5 8. Install End Pilasters to the side wall on the brackets provided, using 35x4mm screws and red plugs. The partitions should be set up 150mm off the floor and accurately aligned with the Mid Pilasters. 9. Drill through the pre-drilled holes in the sides of the channel brackets, and fix the partitions to the pilasters with the hex-head t-nuts provided 10. Adjust the height of the leg(s) as required, position the leg(s) to the correct cubicle centre dimension. 11. The Headrail braces the whole cubicle construction, so correct fitment is essential. Position the Head Rail over the tops of all the Pilasters & Fascia Panels, ensuring that all joints on the Header Rail are positioned over the top of a Pilaster or Panel. 12. Pilot drill the top of the Header Rail and screw down to top of front panels as necessary, ensuring door openings are equal top and bottom. 13. Drill through the pre-drilled holes in the sides of the channel brackets and fix the partitions to the rear wall. Fix the remaining End Pilaster(s) to the end wall(s), with the hex-head t-nuts provided. 14. Ensuring the Partition Support Leg(s) are at the correct height, drill and fix the inner part of the adjustable legs to the floor. 15. Unscrew the hinge assembly, and fix the double-bolt section to the Mid Pilaster(s) and 'hinge' pilaster(s). 16. The remaining part of the hinge fixes to the pre-drilled hole on the door panel. Note: the hinge contains a nylon insert, which can be turned to allow the doors to fall open, or closed. Adjust as required prior to hanging the door and refitting screws. 17. Disassemble indicator bolt, fit through the pre-drilled holes in the door, and reassemble. Fit and adjust keep for the bolt as necessary see instructions for your specific Indicator Bolt I Page 5
6 Individual Component Installation Detail BRACKETS 1. Mark off the central line on the wall 2. Position the brackets on the centre line 3. Mark the two holes per bracket 4. Drill the holes at 5.5mm / minimum depth 50mm 5. Secure the brackets using the wall plugs and screws provided 6. Repeat steps 1. to 3. on the Pilaster or Fascia Panel 7. Secure the brackets to the fascia with the screws provided 8. Position the partition in the brackets 9. Drill through the brackets using a 9.5mm drill 10. Secure the panel to the brackets using the T-Nuts and All-Thread provided Page 6
7 HINGES 1. The Hinges are face fixed to the back of the fascia and the EDGE of the door. 2. To ensure trouble free operation of the hinges it is important to be accurate and as vertical as possible to pre-vent binding of risers. 3. When dismantling the hinge remove the M5x10 Screw from the hinge pin and pull apart. 4. Align hinges to door and partition and 5. When fitting ensure the hinge pin is pointing downward. 6. secure with screws provided. Lift door into place and test for smooth operation. Hinges are supplied in the Door Open Position. 7. When satisfied with operation replace M5x10 Machine Screw to hinge pin. 25mm HINGE PIN THIS HINGE FITTED TO DOOR No.8x2 W/S No.8x3/4 W/S 79mm M5x10 M/HEAD 54mm INWARD or OUTWARD OPENING DOOR OUTSIDE HINGE INSIDE HINGE For outward opening door, turn bolt 1800 so that the slide bolt does not protrude beyond the edge of door. Use an outward opening Keep concealed behind door Page 7
8 PARTITION SUPPORT LEG Edge Design Washrooms supply several styles of Partition Support Leg. The following instructions relate to our most popular leg configuration. If the leg supplied to you is different and you have not received specific instructions for your support leg, please call us on and we will be pleased to assist or send instructions. Page 8 1. Mark all holes / centre line positions as accurately as possible. 2. Take care not to damage hardware or chip powder coatings. 3. Mark off the vertical centre line of the support onto the front edge of the partition, ideally this should be within 250mm from the front edge 4. Loosen the retaining screw in the Leg Shroud and lift up the Shroud to access the adjuster mechanism. adjust the block up into the support as far as it will allow. 5. Offer up the support to the partition and mark out the hole position on the centre line. 6. Drill through using a ø9.5mm drill. 7. Fix support to partition using the M6 T Nuts. 8. The partition can now be mounted to the wall, ensure that the front edge is supported by the use of packing pieces. 9. Once the partition is secure, the support block can be adjusted to floor level taking full support of the partition. 8. Using a ø5.50mm masonry drill, drill through the block following the angle to a depth of 50mm 10. Fit red wall plugs and secure the foot to the floor using the No.8 x 2 Woodscrews. 11. The shroud can now be lowered to the floor and secured using
9 INDICATOR BOLT Edge Design Washrooms supply several styles of Indicator Bolt. The following instructions relate to our most popular styles. If the Indicator Bolt supplied is different to that shown and you have not received specific instructions for your support leg, please call us on and we will be pleased to assist or send instructions. 1. Holes are normally factory pre-drilled. If not Mark out hole centres and slot as shown. 2. Once holes have been drilled, position up the Bolt Housing and Face Plate 3. Secure together with the 2 x M4 Bolts supplied, ensure the Bolt mechanism operates signal correctly. ( Green - Open / Red - Closed) 4. Using 2 x No8. x 1 woodscrews secure the bottom two holes of the Bolt Housing to the Door. 5. Check for free movement of Bolt and Signal. 6. Once satisfied, position the keep to the correct position on the fascia and fix in place with the 2 x No.8 x 5/8 woodscrews supplied. 7. Fit Buffers to top and bottom of the door STANDARD INDICATOR BOLT ECLIPSE INDICATOR BOLT Page 9
10 Section 2 IPS Duct Panel Systems Page 10
11 Optional postformed vertical edges to Access Panels Page 11
12 Section 3 Vanity Units Page Fix support timber batton to rear wall at the appropriate height. Ensure batton is square and does not foul service pipes 2. Fix support timber batton to floor at the appropriate distance from the rear wall 3. Screw through under carcass into bottom of downstand or use angle bracket to fix Under Carcass to Downstand 4. Screw through wall batton into underside of Vanity Top 5. Screw through floor batton into rear of Under Carcass or Vanity Plinth 6. Fix Access Panels to front of Under Carcass using the concealed Keku Clips supplied. Ensure panels are aligned with each other and parallel to the Downstand apron
13 Section 4 Basic Maintenance Cubicle Pilasters, Partitions and Doors Cleaning: Remove general stains and marks with a proprietary non-abrasive bathroom or kitchen surface cleaning solution on a damp cloth. Do not use excessive amounts of water or solution. Avoid scrubbing or using anything with sharp edges. Periodic Inspection: Every 3 months check the cubicle hardware. Spares may be ordered by calling Customer Service on Every 12 months check all panels and edgings for integrity, particularly if they have for any reason become exposed to water or damp atmosphere. Cubicle Hardware Cleaning: The hardware should be cleaned frequently. Satin anodised hardware use a mild anti-bacterial detergent and damp cloth. Powder coated and polished hardware use a polish and non-abrasive cloth. Do not use corrosive chemicals. Lubrication: Lightly lubricate the indicator bolt mechanism every 6 months to ensure continuity of movement. Light lubrication of the hinges is also required to avoid the door sticking and deterioration of the riser. Periodic Inspection: Periodically inspect all fixings, adjust to secure as and when needed. Ensure correct sized allen keys, screw drivers and drill bits are used. Safety mechanisms must also be inspected frequently in case of vandalism. If vandalism occurs the part should be replaced as soon as possible to avoid any accidents. Fitting of 'T' Nuts: When 'T' Nuts are used they should be fitted securely but not too tight to allow movement of the laminate. As the material expands with moisture, pressure is put on the `T' Nuts causing them to sheer off if they are fitted too tight. TO ORDER SPARE PARTS PLEASE CONTACT US ON Page 13
14 Notes
15 Notes
16 Edge design washrooms High street Desford Leicester LE9 9JF Tel : info@edgewashrooms.co.uk Web :
Ultra Fast Delivery SGL Toilet Cubicle Pack Fitting Instructions
Ultra Fast Delivery SGL Toilet Cubicle Pack Fitting Instructions This instructional booklet should be read in full prior to undertaking any work. If in doubt please call Commercial Washrooms on 01202 650900,
More informationINTRODUCTION Tools Required Laminate Washroom Products... 4 DUCT PANELS Fixing the Frame: Fixing the Shadow Panels...
Contents INTRODUCTION... 2 Tools Required... 3 Laminate Washroom Products... 4 DUCT PANELS... 4 Fixing the Frame:... 5 Fixing the Shadow Panels... 9 Fitting the Duct Panels:... 10 WASHSTATIONS... 15 Fixing
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR ONLY ( RECESS) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before
More informationVanity Cabinets and Mirrors Installation and User Guide
Vanity Cabinets and Mirrors Installation and User Guide MODEL NUMBERS 2451, 2452, 2454, 2455, 2457, 2459, 2453, 2456, 2458, 2460, 2470, 2473 Important :- Please quote the above model number(s) when ordering
More informationINFINITE RANGE - HINGE DOOR
INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving
More informationConstable Oak Extension Dining Table
Constable Oak Extension Dining Table Assembly Instructions - Please keep for future reference 176/0325 Dimensions Width - 160/ 200cm Depth - 90cm Height - 75cm Important - Please read these instructions
More informationTransition Range Installation, Care & Adjustment Instructions
Introduction The following instructions will enable you to complete the final assembly and adjustment of your new furniture. Hardware Box Each of the cabinets contains a Hardware box that contains all
More informationHinge Door + Side Panel
Hinge Door + Side Panel Instruction Manual KL+ KR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationInstallation Site Preparation - Site Preparation
S c u l p t u r e s Bespoke Single Door / Bespoke Frameless Hinged Door + Inline Panel Instruction Manual Truelife Consumer Guarantee Please make sure the purchaser/end user completes and returns the Guarantee
More informationFitted Furniture Installation and Aftercare Guide
Fitted Furniture Installation and Aftercare Guide Customer Service Contact Number 08008 778899 Important Information In the unlikely event that your product is damaged or faulty in any way, this must be
More informationTotal Cubicle Solutions
Rainbow Range Cubicles Vanity Units IPS Units Digital Print Rainbow Range Introducing a new dimension in washrooms. When you require a solution that just works, Rainbow provides the answer, being one of
More informationInstallation Manual for Metal Toilet Partitions Elite & Elite Plus Series
P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7
More informationWall Profiles 2 Pozi Screwdriver. Wall Profile Covers 4 Sealant. Large Panel and Thin Panel Assemblies Sealant Gun
Decem Sliding Door (Corner Fitting) Instruction Manual DXT Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed
More informationInstallation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
More informationINSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS
INSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS Table of Contents Topic Page Layout and Wall Brackets 2 Panel and Pilaster Preparation.. 3 Securing Components and Headrail 4 Panel to Pilaster/Wall
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationINSTALLATION INSTRUCTIONS
TEL -866-XANATOS INSTALLATION INSTRUCTIONS PART#: 7D5000SS\7D500A GRILL GUARD FOR DODGE SPRINTER 07-09 PARTS LIST: 8 6 Grille Guard Driver/Left Frame Mounting Passenger/Right Frame Mounting Driver/Left
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationINFINITE RANGE - CENTRE FOLDING DOOR
INFINITE RANGE - CENTRE FOLDING DOOR CENTRE FOLDING DOOR + 2 SIDE RETURN PANELS (PENINSULA) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out
More informationPassenger/Right Front Mounting Bracket
PARTS LIST: 1 Driver side running board 1 8mm Insert Installation Tool 1 Passenger side running board 4 10-1.50mm x 35mm Hex Bolt 1 Driver 10 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger 6 10mm Lock
More informationHinge Door + One Inline Panel
inge Door + One Inline Panel Instruction Manual KLD + KL Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More informationBioPrism Solid Surface
Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1350 COMBAT SERIES TOILET PARTITIONS IMPORTANT: Review these instructions thoroughly prior to installation. In the United States: BOBRICK WASHROOM EQUIPMENT INC. 200 Commerce
More informationHinge Door + Inline Panel + Return Panel
Hinge Door + Inline Panel + Return Panel Instruction Manual DXL2HDR + DXL2HR + DXR Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing
More informationStep-by-step Installation Guide
Product: Resco Series Product Code: S-5000WW Installation Guide Wall to wall version. July 2017 Step-by-step Installation Guide WALL TO WALL VERSION JULY 2017 Job# 5147 Resco Series-5000 WW version. Step-by-step
More informationWeatherfold 4s 50, 75 & 100
Codes Weatherfold 4s 50, 75 & 100 Brio Australia P: +61 2 87186718 W: brio.com.au E: sales@brio.com.au Brio RMD UK Ltd. P: +44 191 2291224 W: briouk.com E: sales@briouk.com INSTBWS1 REV D - NOV 2011 Brio
More informationBathroom Installation Manual
Bathroom Installation Manual MAKING SPACE MORE VALUABLE May 2016 1 2 Contents page 1. Introduction Page 4 2. Tools required / key Page 5 3. Fittings Page 6 4. 600 cistern unit Page 7 5. 600 vanity unit
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationLANSDOWN 400MM FLOOR CUPBOARD (LAN400FC.LW/LAN400FC.PG) INSTALLATION AND AFTERCARE INSTRUCTIONS
LANSDOWN 400MM FLOOR CUPBOARD (LAN400FC.LW/LAN400FC.PG) INSTALLATION AND AFTERCARE INSTRUCTIONS Installation Procedure This unit can be joined to other units with furniture fixing bolts (not provided).
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationBathroom Installation Guide
Bathroom Installation Guide Please read instructions carefully and check products before starting. Products should be fitted/installed by an experienced and competent fitter, failure to do so may invalidate
More informationinstallation instructions
installation instructions Easi-Plan WC Frame 820mm with Dual Flush Cistern ref: EPWC-05-1005 Easi-Plan WC Frame 980mm with Dual Flush Cistern ref: EPWC-05-1505 EASI-PLAN installation instructions Parts
More informationBi-Pass And Bi-Fold Sliders
Bi-Passs and Bi-Fold Sliders Installation Guide Bi-Pass And Bi-Fold Sliders Tools required: Hand Drill Counter Sink Drill BitSet #8 Philips Screw Driver Measuring Tape Level What s Included: Panels with
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationMODEL 1703E THE CHAMBERLAIN ARM TM INSTALLATION INSTRUCTIONS To be used in conjunction with the Lift-Master Garage Door Operator Owner's Manual
MODEL 1703E THE CHAMBERLAIN ARM TM INSTALLATION INSTRUCTIONS To be used in conjunction with the Lift-Master Garage Operator Owner's Before you begin, please read this ENTIRE instruction manual. One- Piece
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationINSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS
INSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS Table of Contents Topic Page Layout and Wall Brackets 2 Panel and Pilaster Prep. 3 Securing Components and Headrail 4 Panel to Pilaster/Wall Assembly.....
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationDOOR BiFOLD DOOR SET (3 + 1)
3 4 DOOR BiFOLD DOOR SET (3 + 1) Bespoke and Standard Sizes 3.6M - 3590mm W x 2090mm H 4.0M - 3990mm W x 2090mm H IB73HEP431 - ISSUE B All products must be installed in accordance with accepted good trade
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationINSTALLATION INSTRUCTIONS
HONEYCOMB & PLEATED Lift & Lock Cordless Lift Systems Standard Top Down/ Bottom Up INSTALLATION INSTRUCTIONS Revised 8/2018 Getting Started A few simple tools are required: - Measuring tape - Carpenters
More informationTYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side
TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS
More informationSunrise Deck Assembly Instructions for Kingston Left
Sunrise Deck Assembly Instructions for Kingston Left It s easiest to build the deck frame first like it will be lying on its back and then after all 4 legs and horizontals are in place, tip the deck toward
More informationBunk Pod Front Entry Assembly Instructions
Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationStuff-Your-Stuff Platform Bed (Twin and Full)
Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete
More informationStainless Steel 95C34 Series
Stainless Steel 95C34 Series Toilet Partition Installation Manual PHONE: FAX: 866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL
More informationUS RACK, Inc Falcon Drive, Madera, CA
US RACK, Inc - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTALLATION AND USE INSTRUCTIONS for Long-John Extension Ladder Rack WARNING: Do NOT attempt to install or use this rack without following
More informationEUROLINE CLASSIC PHENOLIC / EVERGREEN. Installation Instructions. Installation Instructions.
EUROLINE ASSIC PHENOLIC / EVERGREEN EUROLINE ASSIC PHENOLIC / EVERGREEN Before you begin, please note the following considerations: Safety First! Please use proper safety gear when performing any installation.
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationFURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS
www.hafeleindia.com FURNITURE HARDWARE & ACCESSORIES - PART 3 : LEVELLERS AND HANGERS ABOUT ITALIANA FERRAMENTA ITALIANA FERRAMENTA is specialized in the production of high quality accessories and ironmongery
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationWeatherfold 4s 50 & 100 Brio Australia P: W: brio.com.au
Codes INSTBWS2 REV J - MAR 2017 Weatherfold 4s 50 & 100 Brio Australia P: +61 2 87186718 W: brio.com.au E: brio.sales@allegion.com Brio UK P: +44 191 2291224 W: briouk.com E: brio.sales.uk@allegion.com
More informationinstallation instructions WC Frame 1180mm with Dual Flush Cistern
installation instructions WC Frame 1180mm with Dual Flush Cistern (C,D,E) K F/G N L M 12 13 14 16 1 2 11 A 5 6 Q O Y 3 C 10 E D B P,Z,AA R T V S 4 U 2 No. Part no. Description Quantity A WC Frame with
More informationCentre-fold Door. Installation Instructions. Please note: Images shown are for illustration purposes only
Centre-fold Door Installation Instructions Please note: Images shown are for illustration purposes only Please read these instructions in full before installing. The enclosure can be installed to give
More informationPortofino Case2 Installation Guide
Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301
More informationaluminium profile system
aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationCellular Shades SLUMBERSHADE. with energy saving blackout sidetracks. Installation & Care Instructions
Cellular Shades SLUMBERSHADE with energy saving blackout sidetracks Installation & Care Instructions 152725 B 9/14/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationHills Folding Frame Double and Single
Hills Folding Frame Double and Single Product Manual 2 Introduction Congratulations Congratulations on the purchase of your Hills Folding Frame Clothesline, which will bring you many years of trouble free
More informationASSEMBLY INSTRUCTIONS CORONA 2 DOOR 1 DRAWER WARDROBE
ASSEMBLY INSTRUCTIONS CORONA 2 DOOR 1 DRAWER WARDROBE IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR USE YOUR CORONA 2 DOOR 1 DRAWER WARDROBE PLEASE KEEP THESE INSTRUCTIONS
More informationMalibu - 3 Drawer 2 Door Robe
Malibu - 3 Drawer Door Robe ssembly Instructions - Please keep for future reference 7/83 38/3574 58/904 37/187 58/7679 79/1496 6/617 58/803 57/51 79/1960 55/7788 47/766 66/7355 49/661 78/5189 78/0830 Dimensions
More informationInstallation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:
Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationHow to operate (folding)
How to operate (folding) LEFT HAND STACKING OUTWARD OPENING How to operate (folding) RIGHT HAND STACKING OUTWARD OPENING LOCK BOTH LEVER HANDLE AND FLAT HANDLE UTILISING THE D-HANDLE LOCATED ABOVE THE
More informationCUBICLES & LOCKERS. Cubicles Direct, the first choice in affordable solid grade laminate cubicles.
CUBICLES & LOCKERS Cubicles Direct, the first choice in affordable solid grade laminate cubicles. www.cubiclesdirect.co.uk 02 Affordable solid grade laminate, available on a supply only basis. Cubicles
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS
INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS The following information is provided by Plascore, Inc., as a general guideline for the installation of the Plascore Narrow Stile Door and Jamb
More informationAIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS
AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS GENERAL INFORMATION...1 Freight Damage... 1 Repairing Paint Scratches...1 BASE CABINETS... 2 Drawer Removal and Reinstallation...2 Replacing Drawer
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B P7001 Standard Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST
More informationDue to possible damage in shipping, the vertical stop assembly has been removed from this machine.
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationSection 1. Kitchen installation. Base cabinets
Section 1 Kitchen installation Base cabinets Pre-build - Cabinet leg... page 16 Pre-build - Alternative cabinet leg... page 18 Pre-build - Cabinets.... page 19 Pre-build - Corner base cabinet centre upright
More informationGREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5" L 76" W 78.
ASSEMBLY INSTRUCTIONS GREENHOUSE 'x8' (Internal Dimensions) Overall Dimensions (Approx.) 7. L 9 W 00 H cms 97." L 7" W 78.8" H 0 IMPORTANT You must read these instructions carefully before you start to
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationBolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationCellular SlumberShade
Cellular SlumberShade with energy saving blackout sidetracks Installation Instructions 152110 1/6/2011 BASICS A few simple tools are required: - Measuring tape - Power drill, drill bits - Hex head and/or
More informationGENERAL FITTING INSTRUCTIONS FITTED
G07V1.1 U K GENERAL FITTING INSTRUCTIONS FITTED Important : Unpack the units carefully ensuring not to scratch them with the knife blade. Inspect every item carefully before installation as no claim for
More informationSLIDING DOOR for CORNER installation ONLY - this door closes to side panel -
by KUDOS INSTALLATION INSTRUCTIONS SLIDING DOOR for CORNER installation ONLY - this door closes to side panel - Please read these instructions throughout before installing as incorrect fitting will invalidate
More informationModel Series T o r s i o n
Model Series 7100 T o r s i o n Residential and Light Commercial Rear Mount Low Headroom Outside Hookup Table Of Contents Pre-Installation 2 Important Safety Instructions 2 Removing an Existing Door and
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More information8mm x 25mm "Z" Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Side Frame Mounting Bracket 8 12mm Hex Nuts 1 Passenger/Right Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Driver/Left
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Dodge Ram Kit No. 65220, 73132, 75525, 76253 (black) or 65221, 73133, 75530, 76254 (stainless) As you read these instructions, you will see NOTES, CAUTIONS
More informationAssembly Instructions Please keep for future reference Inspire 40
Assembly Instructions Please keep for future reference Inspire 40 Version 3 : 28/07/2014 Important - Please read these instructions fully before starting assembly ALR2902 Safety and Care Advice Important
More information