Open Up Your View With CABLE SYSTEMS

Transcription

1 Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE

2 Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching fittings or studs to the cable. All cable kits include cable that has been swaged at the factory. Interior or exterior use 1/8 diameter, 1x19 construction Framework You Will Need for Cable Railing to Comply with IBC Code Requirements: Minimum 4x4 end posts if using wood Top rail Vertical supports every 48 maximum Cable spacing 3 inch on center Tension cable to 225 lbs. Frame must support minimum of 225 lbs. tension per cable Max. 48 Support cables no more than every 48 Approximately 3 clear opening between cables.

3 Outside-of-Post Mount Pictured: 224 Series Fittings are completely concealed in most installations which maximizes your view. Can be used on stairs without drilling on an angle. No precise measurements needed. Simply pull the cable through the locking fitting, cut the excess cable and snap on the cap. Must have at least 3-1/2 clearance behind post. Ideal for double corner post installations. Cable runs cannot terminate into a single corner post without offsetting the runs.

4 Outside Post Mount Kits Choice Series Traditional stud system design. Budget friendly option. Kit includes washers for both wood and metal installations, cable with attached threaded stud, brass locknut for tensioning, locking fitting, and cap for locking fitting. Available in 5', 10', 15', 20', 25', 30', 40' and 50' kits. Preferred Series Low-Profile end caps. Simple tensioning using only a hex key. Kit includes washers, cable with attached threaded stud, tensioning fitting, locking fitting, and cap for locking fitting. Available in 5', 10',15',20',25', and 40' kits. Preferred Metal Series Low-Profile end caps. Simple tensioning using only a hex key. Fittings designed specifically for 2-3/8 metal post. Kit includes washers for both wood and metal installations, cable with attached threaded stud, tensioning fitting, locking fitting, and cap for locking fitting. *262 and 224 feature same end caps.

5 Accessories Accessories associated with Outside-of-Post Mount kits Bevel Washer (Part# 0326W) Use with 102 or 262 if drilling for your post on an angle. (Sold 4 per pack.) Push Lag (Part# 3059) Use with the 102 or 262 when you do not have access to the backside of the termination post. Push Lag with Clevis (Part# 3057) Use with the 102 or 262 when you do not have access to the backside of the termination post. The fitting pivots for angles and stairs. Stainless End Caps (Part# 3063) Caps for the stud end of the 102. (Sold in packs of 10.) Cut-off Wheel (Part# 3069) Cut cable flush with the ends of fittings. Ideal for the 102 and 262 kits.

6 Inside Post Mount Kits Pictured: Series 300 Runs can be installed into a single post without the need to offset. Sleek and modern fitting designs. Cable must be measured and cut to the appropriate length. Pictured: Series 500

7 Inside Post Mount Kits Select Series Two-piece lag allows for easy installation using a hex key. Kit includes locking fitting, tensioning fitting, wood lag bolts for both fittings, cable with attached stud and lock nut. Available in 5', 10',15', 20', 25' and 40' kits. Select Stair Series Pivots for stairs or unique angles. Kit includes locking fitting, tension fitting, lag bolts for both fittings, lag eyes with screws, cable with attached stud, and lock nut. Available in 5', 10', 15', and 20' kits. Pictured: Combination of 300 and 102 series

8 Ultra-tec Flex System Fittings do not require swaged cable. Simply insert loose cable into the locking fittings. One fitting will also act as the tensioning end. Uses 1/8 loose cable. Sold in 100 (Item# 9100) or 500 (Item# 9500) foot spools. Each system should have one tensioning end and one locking end. Fittings are sold individually or in packs of ten. Compatible with most composite sleeve installations Tensioning end with clevis 3057 Locking end with clevis Tensioning end Locking end

9 Aluminum Railing Pictured: Series 600 Rail Color Options Black Anodized Pictured: Series 200 Rail

10 Aluminum Post Options Our posts are designed specifically for the 224 series cable. The posts measure 2-3/8 and are available pre-drilled or undrilled. Pre-drilled posts are drilled with 10 holes at 3-3/16 on center to achieve a 36 rail height. All post kits include necessary bolt caps and washers. All drilled end post kits include internal post reinforcements. Mounting lags sold separate. Surface Mount Posts Fascia Mount Posts Undrilled Post Surface Mount Post Kit - Includes with 5 base plate - Item# 362SE (34-7/8 ), Predrilled end post for 200 / 400 rail. - Item# 362SI (34-7/8 ), Predrilled intermediate post for 200 / 400 rail. - Item# 366SE (36-3/8 ), Predrilled end post for 600 rail. - Item# 366SI (36-3/8 ), Predrilled intermediate post for 600 rail. Fascia Mount Post Kit - For use on fascia or flush mount installations. Bracket kits sold separately. - Item# 362FE (46-3/8 ), Predrilled end post for 200 / 400 rail. - Item# 362FI (46-3/8 ), Predrilled intermediate post for 200 / 400 rail. - Item# 366FE (46-3/8 ), Predrilled end post for 600 series rail. - Item# 366FI (46-3/8 ), Predrilled intermediate post for 600 series rail. Undrilled Post Kit - Due to the variables involved in stair applications, an undrilled post should be used and field drilled to achieve the appropriate hole placement for all stair installations. All accessories, other than bolt caps and washers, are sold separately. - Item# 426UN, Measures 51 for universal use and stairs.

11 Post Accessories Post Cap (Item# 0410), Use to cap top of post on Series 600 installations and bottom of post on fascia mounts. Post Fitting (Item# 0412), Use to make a continuous run of Series 600 rail over the post Installation Kits - Base Plate Kit (Item# 0414), Use for surface mounting on undrilled post. Included with drilled surface mount post. - Fascia Mount Kit (Item# 0415), Provides a 1 offset from fascia. Includes screws to attach bracket to post. - Double Corner Fascia Kit (Item# 0416), Provides a 1 offset from fascia. Designed to maintain proper alignment in double corner post applications. Includes screws to attach bracket to post. Item# 0414 Item# 0415 Item# 0416 Stainless Steel Lag Bolts - 4pk 5 Wood Lag Kit for Fascia / Surface Mount (Item# 0417) Item# pk 7 Wood Lag Kit for Flush Mount (Item# 0419) - 4pk 3-3/4 Concrete Lag Kit for Fascia / Surface Mount (Item# 0418) - 2pk 6-1/2 Concrete Lag Kit for Flush Mount (Item# 0420)

12 Rail Options Rail sections are sold in 20 ft. lengths to offer the fewest number of joints on longer runs. The rail is field trimmable. Easy to install bottom infill and end caps give the railing a clean, finished look. Infill and caps are sold separately. Series 200 Rectangular wide top. Perfect for your favorite beverage Item# 0110 Infill Pictured with 0112 end cap Series 400 Rail cap to attach you own wood or composite railing Item# 0110 Infill Series 600 The newel post look. Smaller profile allows for installation between posts Item# 0111 Infill Pictured with 0114 end cap

13 Rail Accessories Series 700 Rail Optional bottom rail. Sold in sections of 20 ft. Bottom Infill Plates Item# For Series 200 rail Item# For Series 600 rail and Series 700 Bottom rail Rail End Caps Item# Flush end cap for Series 200 rail Item# End cap for Series 200 rail to terminate rail into a wall. Item# Flush end cap for Series 600 rail Rail Splices to join sections of Series 200 rail Item# Straight splice Item# degree splice Item# Stair splice Rail Connector Block (RCB) Item# 0118 Used to connect rail to post on Series 600 rail and Series 700 Bottom Rail

14 Accessories Cable Braces Use a brace every 48. Measures ¾ x ¾ x 42. Level runs (Part# 4213) Pre-drilled 3-1/8 on center. Stair runs (Part# 4200) Undrilled, includes angle bracket. (Available in both Anodized or Black) Note: For use with wood handrails. Brace can also be an extra post or baluster. Cable Release (Part# 3066) Releases cable from locking fitting before tensioning Post Protector (Part# 3061) Stainless Steel insert. Protects wood post at areas where cable enters / exits on an angle. (Sold 4 per pack.) Cleaner (Part# 3067) Cleans and protects stainless parts from extreme conditions Cable Cutter (Part# 3068) For burr-free cutting of cable.

15 Accessories Painted Screws (100pk) (Item# 0910) - ¾ Screw to attach railing to post and used to attach splices on aluminum railing systems Touch Up (Item# 0911) - For use on Black railing parts Internal Post Reinforcement (Item# 0411) and (Item# 0413) Used to add strength to aluminum post for cable tensioning. Item# brace. Included in fascia / flush drilled post. Order for undrilled post when flush mounting. Item# brace. Included in all drilled post. Order for undrilled post. Interior Post and Rail Suggestions /16 x 2-3/ /16 x 2-1/4

16 CABLE SYSTEMS PRESENTED BY CROWN HERITAGE CROWN HERITAGE PO Box 130 I North Wilkesboro, NC I