PRODUCT INFORMATION MANUAL SECTION: 11-A SILHOUETTE SHADINGS SILHOUETTE SHADINGS

Transcription

1 SILHOUETTE SHADINGS

2 Product View Back/Dust Cover (Optional) Headrail End Cap Installation Bracket Top Limits Headrail Cord Loop and Tensioner Magnetic Hold-Down Brackets (Optional) EasyRise LiteRise ULTRAGLIDE Tassel Handle REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 2

3 IT S SHEER GENIUS LUXAFLEX SILHOUETTE ULTRAGLIDE 2 Shading will allow you to lower your shade with the clever retractable cord with just ONE click. It truly provides added convenience and promotes enhanced child safety. LUXAFLEX EXCLUSIVE. Shading MAGICALLY lowers with just one click. Decreases pull force by 50% making raising the shading easier to operate than ever before. Provides enhanced child safety. One constant cord length. Can cover large window spans with increased limitation Colour co-ordination from the top of the shade to the bottom of the shade. New end cap design which easily snaps on and off. COLOUR COORDINATION Ultraglide 2 Click and walk away hardware system is colour co-ordinated for a consistent design and uniform appearance. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 3

4 Silhouette Ultraglide 2 is a well-engineered product with a vast improvement in operation and aesthetics. ULTRAGLIDE 1 ULTRAGLIDE 2 Colour Co-ordination No Yes Size Limitations Maximum 2440mm x 2440mm Maximum 3040mm x 3040mm Operation Continuous pull action Click and walk away Endcaps One colour with no snap on feature Clear end caps with snap on colour coordinated covers. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 4

5 Pull cord towards centre of shading. Listen for click then release cord and walk away. The vanes automatically open once shading is completely lowered. TO LOWER Gently pull straight down and outward on cord to position angle of vanes. TO TILT VANES Pull cord straight down with long strokes. With each stroke shading partially raises. TO RAISE REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 5

6 NEW END CAPS Clear end caps slide straight into the headrail and easily secure in place with a screw. Colour co-ordinated end cap covers snap on easily and can be attached in the home. The snap on covers allow for quick repair or replacement when necessary. The clear end caps and colour coordinated covers are used across all Silhouette Shadings operating systems, creating uniformity across the range. ENHANCED BOTTOMRAIL As Australian windows are getting bigger, the trend for the contemporary larger vane sizes is increasing. This new and enhanced bottomrail was designed and developed based on the growing popularity for Silhouette Shading 75mm vane fabrics. The clever design not only differentiates the 50mm and 75mm shadings but the aesthetics have dramatically improved when the shading is lowered and vanes are open. A sophisticated finish and clearer view-through are the two main reasons why the 75mm bottomrail was developed. The new bottom rail is available across all Silhouette Shading operating systems. 75mm 50mm REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 6

7 Measuring Architrave & Reveal Face & Reveal Corners Bays REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 7

8 Multi Shades TWO SHADES SIDE BY SIDE THREE SHADES SIDE BY SIDE Product Characteristics LIGHT GAPS LIGHT GAPS (SIDE-BY-SIDE SHADES) MINIMUM RECESS MOUNT DEPTH Control End Idle End Right/Right Controls Left/Left Controls Right/Left Controls Left/Right Controls w/o Back Cover with Back Cover 13mm 7mm 20mm 20mm 26mm 14mm 25mm 30mm MINIMUM REAR FABRIC CLEARANCE 3mm CORD LOOPS WHITE ALL COLOURS* * Colours Include: White, Light Alabaster, Ivory, Cameo Pink, Manilla, Stone, Skyline Blue & Squirrel Grey. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 8

9 Options & Limitations SILHOUETTE Shadings - EASYRISE (Continuous Cord) Silhouette EasyRise Originale 50mm Originale 75mm Voila 75mm Sunscreen Privacy Shadings 75mm Matisse Collection 75mm Bon Soir 50mm Nouveau 75mm Matisse Collection Bon Soir 75mm Bon Jour 50mm & 75mm Minimum Width 300mm 300mm 300mm 300mm 300mm Maximum Width 2740mm 3040mm 3040mm 3040mm 3040mm Minimum Drop 300mm 300mm 300mm 300mm 300mm Maximum Drop 3050mm 3050mm 2590mm 2840mm 2440mm Light Gaps Control side Idle End 13mm 7mm 13mm 7mm 13mm 7mm 13mm 7mm 13mm 7mm Minimum Rear Fabric Clearance 3mm 3mm 3mm 3mm 3mm Minimum Recess Depth Oversize Headrail Depth 25mm 83mm 25mm 83mm 25mm 83mm 25mm 83mm 25mm 83mm Fully Recessed Box Mount 110mm 110mm 110mm 110mm 110mm Face Mount Min/Height 20mm 20mm 20mm 20mm 20mm Face Mount Min Above Opening Aluminium Cover Strip PVC Cover Strip Cord Loops 57mm 57mm 57mm 57mm 57mm FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT White: All Colours: Back Cover Min. Recess Mounting Depth W/o Back Cover 25mm With Back Cover 30mm W/o Back Cover 25mm With Back Cover 30mm W/o Back Cover 25mm With Back Cover 30mm W/o Back Cover 25mm With Back Cover 30mm W/o Back Cover 25mm With Back Cover 30mm Tilt Only Min Width 150mm 150mm 150mm 150mm 150mm REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 9

10 Silhouette PowerRise Minimum Width Battery Operated Minimum Width Dc Power Supply Options & Limitations SILHOUETTE PowerRise Shadings Originale 50mm Bon Soir 50mm Bon Soir 75mm Matisse Bon Soir 75mm Bon Jour 50mm & 75mm Nouvuea 75mm Originale 75mm Matisse 75mm Sunscreen Privacy Shadings 75 Voila 75mm 510mm 510mm 510mm 510mm 510mm 310mm 310mm 310mm 310mm 310mm Maximum Width 2760mm 3040mm 3040mm 3040mm 3040mm Minimum Drop 300mm 300mm 300mm 300mm 300mm Maximum Drop 3040mm 2590mm 2840mm 2440mm 3040mm Light side Gaps Control Idle End Minimum Rear Fabric Clearance Minimum Recess Depth Full Depth Fully Recessed Box Mount Face Mount Min/ Height Face Mount Min Above Opening Aluminium Cover Strip PVC Cover Strip 13mm 7mm 13mm 7mm 13mm 7mm 13mm 7mm 13mm 7mm 3mm 3mm 3mm 3mm 3mm 25mm 108mm 25mm 108mm 25mm 108mm 25mm 108mm 25mm 108mm 110mm 110mm 110mm 110mm 110mm 20mm 20mm 20mm 20mm 20mm 57mm 57mm 57mm 57mm 57mm FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT FULL FACE FIT PARTIAL FACE FIT Satellite Infra Red Eye Cord Lengths 400mm 1200mm 2400mm 400mm 1200mm 2400mm 400mm 1200mm 2400mm 400mm 1200mm 2400mm 400mm 1200mm 2400mm Back Min.Recess Cover Mounting Depth W/O Back Cover 25mm With Back Cover 30mm W/O Back Cover 25mm With Back Cover 30mm W/O Back Cover 25mm With Back Cover 30mm W/O Back Cover 25mm With Back Cover 30mm W/O Back Cover 25mm With Back Cover 30mm REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 10

11 Thank you for purchasing LUXAFLEX SILHOUETTE Shadings. With proper installation, operation, and care, your new shadings will provide years of beauty and performance. Please thoroughly review this instruction booklet before beginning the installation. If your shading has a protective plastic cover on the fabric-covered headrail, keep the plastic in place until the shading is installed. Tools and Fasteners Needed Flat blade and Phillips screwdriver Measuring tape and pencil Power drill, 3mm drill bit, and a 6mm hex driver Level (laser level is recommended) Pliers Scissors (heavy-duty) In addition, you will need fasteners designed to work with your specific mounting surface(s). #6 Hex Head Screws (Provided). Two 38mm screws are provided per installation bracket. Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long enough for a secure attachment. Speed Nuts and Screws (Provided). Extension brackets come with screws and speed nuts. Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. #6 x 38mm Hex Head Screw (Provided) Longer #6 Hex Head Screw for Use with Spacer Blocks (Not Provided) Speed Nut and Screw (Provided With Each Extension Bracket) Importance of Limit Stops on Silhouette Shadings Limit stops serve as the upper travel limit for the bottom rail, preventing it from rotating around the fabric roll. Limit stops are located 150mm from the ends of the headrail or are centred on shadings less than 915mm wide. When a shading is made, the limit stops are adjusted according to the size of the fabric roll. Occasionally, this adjustment changes during shipping or installation. If this happens, problems can be fixed by readjusting the limit stops. See the Troubleshooting section if shading operation is difficult or if the bottom rail rotates around the fabric roll. Shown below are the four possible positions of limit stops for large to small fabric rolls. Large Fabric Roll Small Fabric Roll REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 11

12 Installation Overview The number of installation brackets required varies with shading width, as shown in the table. Single Panel Shadings Installation Bracket Width (mm) Mounting Types and Window Terminology Brackets Required 310mm 910mm 2 911mm 2000mm mm 2400mm mm 3040mm 5 If the installation brackets are mounted correctly, the rest of the installation process follows very easily. To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the window casement. Sill Reveal Mount Shading fits within window opening. Face Mount Shading mounts outside window opening. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 12

13 Mount the Installation Brackets Reveal Mount Mark 50mm 75mm from each jamb for bracket location. If more than two installation brackets came with your order, space additional bracket(s) evenly between the two end brackets and mark their location. Mount into wood whenever possible. Lever Use pliers to break off the top tab of each installation bracket. Save this tab once removed. It may be used as a shim, as described later Top Tab 50mm 75mm Space Evenly Space Evenly 50mm 75mm Bottom Tab Jamb Top limits should be equal distance from the ends of headrail. Jamb in these instructions. Decide whether the front or back set of holes works best in your application. Mark the location of the screw holes. The depth required for fully recessed mounting will vary depending on the type of headrail and vane size. Refer to the chart below for depth requirements. Depth Chart for Bracket Placement Headrail Type Minimum Fully Recessed Oversized 25mm 85mm 50mm - 75mm Minimum Depth See Chart Note: Add 6mm to the minimum depth dimensions if the optional back cover is used for inside mounts. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 13

14 Use a level to check that the mounting surface is level. Shim the brackets, if necessary (use the top tab that was removed from the brackets.) Drill the screw holes using a 3mm drill bit. IMPORTANT: Use drywall anchors when mounting into drywall. Attach the installation brackets using the screws provided. IMPORTANT: Do not overtighten the screws. Check to ensure the lever can be moved easily side to side. If the lever is not moving easily, loosen the screws 3mm of a turn increments until it can be moved easily. IMPORTANT: The front edges of the installation brackets must be level and aligned to each other. Mount the Installation Brackets Face Mount Centre the headrail over the window opening at the desired height. Use a pencil to lightly mark each end of the headrail. Alternatively, measure the width of the headrail and use that width to mark the headrail end points over the window opening. Headrail End Marks 50mm 75mm Space Evenly Space Evenly 50mm 75mm Window Opening Mark 50mm 75mm from each end of the headrail, for bracket location. If more than two installation brackets came with your order, space additional bracket(s) evenly between the two end brackets and mark their location. Mount into studs whenever possible. Use pliers to break off both removable tabs from the installation. Top Tab Lever Bottom Tab REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 14

15 brackets. Centre each installation bracket on your marks and mark the location of the screw holes. CAUTION: The rear of the blocks/brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. A minimum 30mm flat vertical height is required to mount the installation brackets. The top of the installation brackets should be at the desired height of the shading. The brackets should be level and aligned. Use a 3mm drill bit to drill holes for the mounting screws. IMPORTANT: Use drywall anchors when mounting into drywall. Attach the installation brackets using the screws provided. IMPORTANT: The front edges of the installation brackets must be level and aligned to each other. Additonal Clearance If using 6mm or 13mm spacer blocks, attach the spacer block(s) and installation bracket to a flat vertical mounting surface with #6 screws long enough for a secure installation. Longer screws are not provided. IMPORTANT: The maximum spacer block allowance is 40mm. 30mm Maximum Spacer Blocks If using extension brackets, attach each extension bracket to a flat vertical mounting surface. Attach an installation bracket to the underside of each extension bracket using the provided screws and speed nuts. Extension Bracket Speed Nuts REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 15

16 Mount the Installation Brackets End Mount End mount the headrail when conventional mounting techniques will not work for example, in an arched window opening. Mount the extension brackets on a surface at least 35mm wide. Add 6mm to the minimum depth if using the optional back cover. Attach the installation brackets to the extension brackets using the provided screws and speed nuts. Extension Bracket CAUTION: To end mount shadings into a surface other than a secure wall stud, use medium to heavy-duty wall anchors (not provided) matched to the wall thickness. Failure to mount the brackets securely may result in injury or property damage. 35mm Minimum Depth Attach the Back Cover (Optional for Reveal or End Mounts) If using the back cover, use heavy-duty scissors to cut off the top tabs on the back cover brackets and both top and bottom tabs on the installation brackets. Snap the prongs on the back cover brackets into the holes on the back of the installation brackets. After bracket installation, install the cover into the back cover brackets, as shown. If necessary, trim the back cover with scissors to the desired width. Remove Top Tab Back Cover Bracket Back Cover Installation Bracket REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 16

17 Install the Shading Peel back the protective covering from the top of the fabric-covered headrail. Leave the rest of the protective covering on the front of the headrail. Position the shading so that the front faces you. Installation Bracket Slide the headrail into the installation brackets so the edge of the headrail is between the lever and the bracket, as shown. Firmly push the headrail into each bracket until it clicks and the lever snaps to the right side of the bracket. IMPORTANT: Carefully pull on the headrail at each bracket to ensure it is installed securely. Completely remove the protective covering from the fabric covered headrail. Attach the Universal Cord Tensioner (UCT) for EasyRise Only IMPORTANT: Before you proceed, you must first slide the cord tensioner to the bottom of the cord loop. Insert a small screwdriver, punch, or awl through the screw hole at the bottom of the cord tensioner. Move the screw hole down to the indicator line to release the safety mechanism. Slide the cord tensioner down to the bottom of the cord loop. Attach the cord tensioner according to the instructions provided with the Universal Cord Tensioner Installation Kit. Lever Headrail Slide the Headrail Between the Lever and the Bracket Universal Cord Tensioner Indicator Line WARNING: It is imperative that the cord tensioner be properly secured to the wall or window frame to reduce children s access to the cord loop. Young children can strangle in cord loops. They can also wrap cords around their necks and strangle. CAUTION: The shade will not operate properly unless the cord tensioner is secured. A Universal Cord Tensioner Installation Kit has been included with your shade. Follow the instructions in the kit to correctly secure the cord tensioner. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 17

18 UNIVERSAL CORD TENSIONER Before doing anything, you must first slide the universal cord tensioner to the bottom of the cord loop. Insert a small screwdriver, through the screw hole at the bottom of the cord tensioner. Move the screw hole down to the indicator line to release the safety mechanism. Slide the cord tensioner down to the bottom of the cord loop. Install the window covering and use the following instructions to secure the cord tensioner to the window casement. CAUTION: The shading will not operate properly unless the cord tensioner is secured. Only supplied cord tensioners and cord tensioner hardware should be used. MOUNTING OPTIONS Reveal Mount without a Bracket Where the cord tensioner is attached with one screw through the screw hole. Be sure the cord tensioner is not placed in the path of the bottom rail and fabric. To install the cord tensioner, mark screw locations. Insert a small tip screwdriver into the screw hole on the cord tensioner. Pull the screw hole down so that its centre aligns with the indicator lines on the cord tensioner. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 18

19 Hold the cord tensioner firmly in place and check that the cord can move freely through it. If the cord does not move freely through the cord tensioner, it is too tight and the cord tensioner and/or bracket should be moved up. If the cord tensioner locks onto the cord, it is too loose and the cord tensioner and/or bracket should be moved down. Mark and pre-drill the screw hole. Mount the cord tensioner with a Phillips screwdriver and one of the longer screws provided to attach the cord tensioner directly to the wall. Finally, ensure the cord can move freely through the cord tensioner without engaging the lock. The centre of the screw hole should be aligned with the indicator line on the cord tensioner. Do not pull the screw hole down to the bottom of the slot. This may cause the cord to become too tight, affecting the window covering function and increasing cord wear. Reveal Mount with a Bracket This option uses three screws with the inside mount bracket and slightly projects the cord loop from the window covering allowing for easier access. Locate the cord tensioner as close to the window glass as possible to minimize accessibility by children and pets. Be sure the cord tensioner is not placed in the path of the bottom rail and fabric. Reveal Face Break off the inside mount bracket and mark screw locations. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 19

20 Attach the inside mount bracket to the cord tensioner. The nub on the inside mount bracket fits into the back of the screw hole in the cord tensioner. Insert the small screw into the front of the screw hole to secure the cord tensioner to the bracket. Pull down on the bracket, aligning the centre of the screw hole with the indicator line on the cord tensioner. Hold the cord tensioner firmly in place and check that the cord can move freely through it. If the cord does not move freely through the cord tensioner, it is too tight and the cord tensioner and/or bracket should be moved up. If the cord tensioner locks onto the cord, it is too loose and the cord tensioner and/or bracket should be moved down. Mark and pre-drill the screw holes. To mount the cord tensioner, pull down on the inside mount bracket and align it with the drilled holes. Insert one of the two longer screws and loosely attach the bracket to the wall. Pivot the bracket to align it with the second screw and attach the second screw. Tighten both screws. Ensure the cord can move freely through the cord tensioner without engaging the lock. The centre of the screw hole should be aligned with the indicator line on the cord tensioner. Do not pull the screw hole down to the bottom of the slot. This may cause the cord to become too tight, affecting the window covering function and increasing cord wear. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 20

21 Face Mount This option uses three screws and is attached to an outside mount bracket. Locate the cord tensioner as close to the window covering as possible to minimize accessibility by children and pets. Be sure the cord tensioner is not placed in the path of the bottom rail and fabric. Break off the outside mount bracket and mark screw locations. Reveal Face Attach the outside mount bracket to the cord tensioner. The nub on the outside mount bracket fits into the back of the screw hole in the cord tensioner. Insert the small screw into the front of the screw hole to secure the cord tensioner to the bracket. Pull down on the bracket, aligning the centre of the screw hole with the indicator line on the cord tensioner. Hold the cord tensioner firmly in place and check that the cord can move freely through it. If the cord does not move freely through the cord tensioner, it is too tight and the cord tensioner and/or bracket should be moved up. If the cord tensioner locks onto the cord, it is too loose and the cord tensioner and/or bracket should be moved down. Mark and pre-drill the screw holes. To mount the cord tensioner, detach the cord tensioner from the bracket by removing the small screw. Use a Phillips screwdriver and the two longer screws provided to attach the outside mount bracket to the wall. Reattach the cord tensioner to the outside mount bracket using the smaller screw provided. Ensure the cord can move freely through the cord tensioner without engaging the lock. The centre of the screw hole should be aligned with the indicator line on the cord tensioner. Do not pull the screw hole down to the bottom of the slot. This may cause the cord to become too tight, affecting the window covering function and increasing cord wear. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 21

22 Final Adjustments Adjust the Cord Length for ULTRAGLIDE Operating System Only Adjusting the tassel to eye level will decrease the amount of pulls needed to raise and lower the shading. This will also enhance child safety. To Shorten the Tassel Cord Grasp both parts of the tassel (the coloured cover and the frosted body). Squeeze the tassel cover with your thumb and forefinger Separate and slide the tassel cover from the tassel body. Pull out the knotted end of the tassel cord. Retie the cord at the desired shorter length, using a double knot. Trim the tassel cord. Pull the trimmed knot up inside the tassel. Squeeze the sides of the tassel cover together while sliding it back onto the tassel body. IMPORTANT: After reassembling, be sure there are no gaps between the two components. Check that they do not pull apart easily. The tassel cover should be securely seated into the tassel body. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 22

23 Attach the Magnetic Hold-Down Brackets (Optional) Lower the shading, keeping the vanes closed. Place the magnetic hold-down bracket onto the bottom rail just inside the end cap, oriented as shown. Hold the bracket while opening and closing the vanes (it may be necessary to have someone assist you). Adjust the bracket to the best overall position. Mark the screw location using the mounting options shown below. The screw should be placed in the middle of the channel. This will allow for adjustment. Hold-Down Bracket Bottom Rail Face Mount Preferred Alternate Reveal Mount Preferred Alternate Drill the screw holes using a 3 /32" drill bit. Drill the screw holes using a 3mm drill bit. IMPORTANT: Use drywall anchors when mounting into drywall. Attach the hold-down brackets to the mounting surface using the screws provided. If necessary, adjust bracket height by loosening the screw and sliding the bracket up or down. Adjust bracket height by loosening the screw and sliding the bracket up or down. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 23

24 Attach the Dust Cover (Optional for Face Mounts and End Mounts) The dust cover is used to protect the top of the headrail from exposure on outside mounted shadings. Cut the dust cover to desired width. Remove the paper backing on one side of the hook and loop fastener dots. Apply the dots to the installation brackets on each end of the shading. Overhead View No Dust Cover Remove Paper Backing Dots Remove the remaining paper backing from the dots. Centre the dust cover over the top of the shading, above the dots. Press the dust cover down onto the dots. Dust Cover Installed Install the Pull Tassel (Optional for LiteRise Operating System Only) Rotate the bottom rail so that you can see the underside of the handle. Push the pull cord loop through the hole at the back of the handle. Thread the pull tassel through the loop. Pull the tassel to secure. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 24

25 Operate the Shading To Lower and Open the Vanes of the Shading EasyRise Shadings To Lower the Shading and Open the Vanes Pull the rear cord of the cord loop down to lower the shading. With the shading fully lowered, continue to pull the rear cord to tilt the bottom rail and open the vanes. If the cord tensioner moves up the cord, you have not secured it to the wall or window frame. You must do so for the shading to operate properly. Cord Tensioner and Bracket Front Side of Shading To Close the Vanes and Raise the Shading Pull the front cord of the cord loop down to close the vanes and raise the shading. If the cord tensioner moves up the cord, you have not secured it to the wall or window frame. You must do so for the shading to operate properly. IMPORTANT: If the shading raises or lowers unevenly, the fabric rubs against one end of the headrail, or the bottom rail is uneven when fully raised, the bottom rail weight needs to be adjusted. To Close Vanes and Raise the Shading Cord Tensioner and Bracket Front Side of Shading REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 25

26 Ultraglide 2 Click and Walk Away Shadings To Lower the Shading and Open the Vanes Pull the cord toward the centre of the shading. Listen for a click and then release the cord. The vanes automatically open once the shading is completely lowered. The shading can be stopped at any point while lowering by slightly tugging the cord straight down. Lower and Open Vanes by Pulling to Centre To Tilt the Vanes and Raise the Shading Pull the cord straight down with long strokes. Pull the cord with shorter strokes to tilt the vanes. With each stroke, the vanes close or the shading partially raises. Allow the cord to retract completely into the headrail after each downward stroke. Use multiple strokes until the shading reaches the desired position. The shading can be stopped at any point while raising. Tilt Vanes and Raise by Pulling Straight Down REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 26

27 LiteRise Shadings To Lower Slowly and steadily pull down on the bottom rail handle to lower. To Open With your thumb on the front of the handle and fingers on the back, gently pull the back of handle down and away from the shading to open the vanes. Use the handle to tilt the vanes to the desired open/closed position. To Raise Push down on the front of the handle to close the vanes. Then slowly and steadily push up on the handle to raise. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 27

28 Troubleshooting Problem Solution Vanes do not align on side-by-side shadings. Vane alignment is only guaranteed within 6mm when shadings are ordered at the same time, at the same height, with the same color and fabric, and when specified on the order form. Check that the windows are square and the same height. Problem Solution The shading is hard to raise or lower, or will not raise or lower. Shadings cannot be forced into tight inside mount window openings. If an inside mount, check that the shading is installed correctly. Make sure there is clearance between the ends of the shading and the window casement. For LiteRise Operating System Only: If the vanes are open, be sure to close the vanes first by pressing down on the front of the handle. If necessary, pull the shading away from the window to fully close. Once the vanes are closed, you can raise the shading. For EasyRise Operating System Only: Check that the universal cord tensioner is mounted correctly. Pull down on the spring to relieve tension and pull the universal cord tensioner to the bottom of the cord loop. Properly mount the cord tensioner. See the Universal Cord Tensioner Installation Instructions included with your shading. Check that the installation brackets are level. Shim to level, if necessary. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 28

29 Problem Solution Problem The shading will not snap into the installation brackets. Check that the installation brackets are aligned and level. Check that the locking tab on the installation bracket slides over the headrail. The shading raises or lowers unevenly or the bottom rail is uneven when fully raised. Solution Problem Solution Check that the window is square by measuring the diagonals. Check that the installation brackets are level. Shim to level, if necessary. Adjust the bottom rail weight (not applicable for LiteRise Shadings). See below. For LiteRise Operating System Only: Keep the bottom rail level while raising the shading. Side-to-side movement while raising may cause the fabric to skew. The shading raises or lowers unevenly, the fabric rubs against one end of the headrail, or the bottom rail is uneven when fully raised. Check that the installation brackets are level. Shim to level, if necessary. Adjust the bottom rail weight (not applicable for LiteRise Shadings). See below. Adjusting the Bottom Rail Weight Weight Clip Weight Weight Clip To release the weight clip, insert a flat blade screwdriver into the weight clip and turn clockwise. Move the weight in 25mm increments toward the side where the fabric is gathering. Secure the weight clips in position by turning them counterclockwise after making the adjustment. Test and, if necessary, adjust again. Fabric Roll Move Weight REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 29

30 Problem EasyRise Shadings Only: The universal cord tensioner has climbed to the headrail. Solution Problem Pull down on the spring to relieve tension and pull the universal cord tensioner to the bottom of the cord loop. Properly mount the cord tensioner. See the Universal Cord Tensioner Installation Instructions included with your shading. EasyRise Shadings Only: The universal cord tensioner grabs onto the cord upon operation. Solution Check that the universal cord tensioner is mounted properly. Reinstall, if necessary. Problem. Solution Problem LiteRise Shadings Only: Vanes will not open. With your thumb on the front of the handle and fingers on the back, gently pull the back of handle down and away from the shading to open. The shading must be fully lowered to tilt it open. Ultraglide Shadings Only: The tassel cord and lower cord connector have detached from the upper cord connector. Solution To Reattach the Tassel Cord: Hook one side of the lower cord connector to the upper cord connector. Rotate the lower cord connector until it snaps into place. Twirl the tassel cord to pull any stray cord fibers out of the junction of the cord connector halves. Stray fibers in the junction may cause the connector to come apart. Upper Cord Connector Lower Cord Connector Tassel Cord (Attached to the Lower Cord Connector) REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 30

31 Problem The shading is hard to raise or lower, or the bottom rail does not stop at the top limit. Solution Check the adjustment position of both limit stops. The top illustration Headrail Limit Stop shows the correct adjustment. The limit stop catches the bottom rail, and the bottom of the limit stop is slightly above or barely touching the Fabric Roll Bottom Rail fabric roll. In the second illustration, the limit stop adjustment is too tight. The fabric may not drop freely and could even be damaged when the shading Pull Back to Adjust is raised. To correct this, the limit stop should be adjusted one step up. Simply pull back on the rear of the Too Tight Adjust One Step Up limit stop to adjust its position. In the bottom illustration, the adjustment is too loose. The bottom rail can slip under the limit stop. Pull Back to Adjust If the bottom rail rotates through the headrail, it must be backed out before adjusting the limit stop. IMPORTANT: Both limit stops must Too Loose Adjust One Step Down be adjusted to the same position or else skewing may occur. Problem Solution The shading raises or lowers unevenly or the bottom rail is uneven when fully raised Check that the window is square by measuring the diagonals. Check that the installation brackets are level. Shim to level, if necessary. Adjust the bottom rail weight (not applicable for LiteRise Shadings). For LiteRise Operating System Only: Keep the bottom rail level while raising the shading. Side-to-side movement while raising may cause the fabric to skew. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 31

32 Removing the Shading Move each lever of the installation brackets to the left to release the shading. A flat blade screwdriver can be used to move the lever. CAUTION: Be very careful to not tear or damage any of the fabric. If the lever is inaccessible or inoperable, lower the shading until you can see the underside of the bracket. Carefully reach a small flat blade screwdriver behind the shading to the tab on bottom of the bracket between the screw holes. Push the tab away from the shading and pull the headrail to release it from the bracket. Carefully pull the shading to remove it from the brackets. Underside of Bracket Top View Move the lever to the left to release the shading. Tab Installation Bracket End Cap REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 32

33 Cleaning Procedures LUXAFLEX SILHOUETTE Shadings are made of 100% polyester, which means they are inherently durable and resilient. However, care must be taken to avoid wrinkling the fabric, particularly where the vanes meet the facings. The Palette Fabric-Covered Headrail Spot-clean the headrail using a sponge or delicate cloth, cool distilled water and a mild soap solution; handle with care as you would any fine fabric. Only available with The Matisse Collection, Terra and India Silk. Dusting Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances. Vacuuming Use a low suction, hand-held vacuum for more thorough dust removal. Forced Air Blow away dirt and debris between the vanes using clean compressed air. Spot-Cleaning Do not spot-clean anything other than the Palette Fabric-Covered Headrail on Silhouette Shadings. Ultrasonic Cleaning Silhouette Shadings can be ultrasonically cleaned by a professional, with the exception of The Matisse Collection, Bon Soir, Ombre, Brio, India Silk and all room darkening fabrics. Specify that a mild detergent solution be used. Never immerse the headrail in the solution. Dry the shading completely in the lowered position. Injection/Extraction (LUXAFLEX Onsite Blind Cleaning) Silhouette Shadings can be professionally cleaned using the injection/extraction method. Use only the dry method of injection/extraction for Bon Soir, Ombre and Brio Bon Soir. Never immerse the headrail in the solution. NOTE: Only available in limited regions. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 33

34 Electrostatic Cleaning Do not use electrostatic cleaning wipes on any Silhouette Shadings. A Note About Silhouette Fabrics As with all textiles, Silhouette fabrics are subject to some variations. Slight wrinkling, puckering, or bowing is inherent to this textile product and should be considered normal, acceptable quality. These characteristics are not usually visible from the front or rear but may be visible from a side angle. Precautions should be taken to reduce exposure to harsh environmental elements, such as salt air. Continuous exposure through open windows and doors will accelerate the fabric deterioration. A Note About the Metalised Hardware Colours Gold Radiance, Silver Reflection, Bronze Shimmer and Champagne Shine hardware finishes can be spotcleaned with luke warm water and a gentle soap. Do not use alcohol, baby wipes or alkaline cleansers. These may stain or destroy the finish. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 34

35 Silhouette /Nantucket EasyRise Classic Single Only Used On Chateau Fabric 1. Headrail End Plate 2. Idler Assembly 3. Screw, FLH PHH #8-18 x 0.75" 4. Rotator Rail, LW, Universal 5. RB Clutch ER 6. Screw (Clutch), #10 X 1³ ₈" SHWH Zinc-Plated Standard Parts 7. Cord Loop 8. Universal Cord Tensioner 9. Headrail, Fabric Covered 10. SU Std. Top Limit 11. Bottom Slat 12. Bottom Rail 13. Bottom Rail End Caps 14. Balance Weight 15. Weight Clips 16. Fabric 17. Polystrip With Tape 18. SU Steel Insert Strip 19. FCH Fabric 20. Full Width Tape 21. Cover Set 2015 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. Revision: 1/12/15 REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 35

36 Silhouette /Nantucket EasyRise Classic Single No. PCN Description 1. Headrail End Plate RH LH 2. Idler Assembly RH LH Screw, FLH PHH #8-18 x 0.75" xxx Rotator Rail, LW, Universal RB Clutch ER Screw (Clutch), #10 X 1³ ₈" SHWH Zinc-Plated 7. Cord Loop xxx 1' xxx 2' xxx 3' xxx 4' xxx 5' xxx 6' xxx Universal Cord Tensioner xxx Headrail, Fabric Covered 10. Top Limit SU Std XL (Only Used On Chateau Fabric Shadings) 11. N/A Bottom Slat 12. Bottom Rail xxx Classic All Fabrics Except Chateau xxx 3" For Chateau Fabrics Only 13. Bottom Rail End Caps xxx Classic All Fabrics Except Chateau xxx 3" For Chateau Fabrics Only xxx Balance Weight xxx Weight Clips 16. N/A Fabric Polystrip With Tape 18. SU Steel Insert Strip Short XL, Long For Chateau Fabrics Only NOTE: For 3" Chateau bottom rail, use one short and one long steel insert strip on each side. 19. N/A FCH Fabric 20. Full Width Tape SU FW Tape, 3.219" X 320 Yards NAN FW Tape, 3.219" X 60 Yards xxx Cover Set xxx = 3 Digit Color Code 2015 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. Revision: 1/12/15 REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 36

37 PRODUCT INFORMATION MANUAL SECTION: 11-A SILHOUETTE SHADINGS Silhouette /Nantucket UltraGlide 2 Click and Walk Away Classic Single Shading Only Used On Silhouette 3" Fabrics Standard Parts Cover Set Clutch and Booster End Cap Set Screw, FLH PHH #8-18 X 0.75 Booster Assembly One Way & Governor Assembly Top Limit Fabric Headrail, Fabric Covered Polystrip With Tape Rotator Rail, LW, Universal 11. FCH Fabric 12. Lower Cord Connector 13. Drop Cord 2.2 mm, D Designer Tassel Cover Designer Tassel Base Balance Weight Weight Clips Bottom Rail End Caps Bottom Rail Bottom Slat SU Steel Insert Strip Full Width Tape 2015 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA Revision: 2/13/15 PAGE 37

38 Silhouette /Nantucket UltraGlide 2 Click and Walk Away No. PCN Classic Single Shading Description xxx Cover Set 2. Clutch and Booster End Cap Set LH RH Screw, FLH PHH #8-18 X Booster Assembly Spring LH Spring LH Spring LH Spring LH Spring LH Spring RH Spring RH Spring RH Spring RH Spring RH 5. One Way & Governor Assembly Gov-One Way Assy, X2 Heavy RH Gov-One Way Assy, X2 Heavy LH Gov-One Way Assy, Heavy LH Gov-One Way Assy, Heavy RH Gov-One Way Assy, Med LH Gov-One Way Assy, Med RH Gov-One Way Assy, Lite LH Gov-One Way Assy, Lite RH 6. Top Limit Std. (Used On 2" Silhouette Fabrics And All 3" Nantucket Fabrics) XL (Only Used On All 3" Silhouette Fabrics) 7. N/A Fabric xxx Headrail, Fabric Covered Polystrip With Tape xxx Rotator Rail, LW, Universal 11. N/A FCH Fabric Lower Cord Connector xxx Drop Cord 2.2 mm, D xxx Designer Tassel Cover Designer Tassel Base xxx Balance Weight xxx Weight Clips 18. Bottom Rail End Caps xxx Classic All 2" Silhouette Fabrics And 3" Nantucket Fabrics xxx 3" All 3" Silhouette Fabrics 19. Bottom Rail xxx Classic Used On 2" Silhouette Fabrics And 3" Nantucket Fabrics xxx 3" Used On All 3" Silhouette Fabrics 20. N/A Bottom Slat 21. SU Steel Insert Strip Short XL, Long 22. Full Width Tape SU FW Tape, 3.219" 320 Yards For All Fabrics Except Chateau SU FW Tape, 3.219" 320 Yards For All Chateau Fabrics xxx = 3-digit color code 2015 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. Revision: 2/13/15 REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 38

39 Thank you for purchasing Hunter Douglas window fashions. As the leading manufacturer of custom window coverings in North America, we re committed to providing you with the highest level of quality and service while delivering style and beauty that transforms your home. Should you need assistance with your Hunter Douglas products, feel free to contact your local dealer or visit our website hunterdouglas.com/customersupport at. We hope you will take the time to complete and return the Warranty Registration Card which came with your Hunter Douglas products. You may also complete it online. For more information, please hunterdouglas.com/warrantycard visit. PRODUCT INFORMATION MANUAL Silhouette /Nantucket UltraGlide 2 Click and Walk Away Standard Additional Hardware x Hunter Douglas Warranty Registration Card Silhouette Nantucket Ultra- Glide Standard and Two-On-One Headrail IOC. PCN Lever Installation Brackets 2 Pack KIT9109 (Shown) 3 Pack KIT9110 Hunter Douglas Warranty Registration Card PCN Alustra Thank You Card PCN Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. Revision: 5/07/15 REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 39

40 Silhouette /Nantucket UltraGlide 2 Click and Walk Away Optional Hardware x2 x2 ¹ ₂" Spacer Block 2-Pack KIT Pack KIT2012 ¹ ₄" Spacer Block 2-Pack KIT Pack KIT9115 Back/Dust Cover PCN Back Cover Bracket KIT9116 (2 Pack) KIT9117 (3 Pack) x2 x2 Silhouette Nantucket Dust Cover Installation Kit Loops PCN Hooks PCN Magnetic Hold-Down Bracket Kit (contains two magnet holddown brackets and two ³ ₄" screws) KIT9108 Extension Bracket KIT2013 (2 Pack Shown) KIT2014 (3 Pack)) Magnetic Hold-Down Bracket Retro-Fit Kit KIT9111 x8 Mounting Screws #6X1.5 KIT Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas. Revision: 10/17/14 REPLACES ISSUE DATE: FEB 2018 APPROVED BY: D.ALTIPARMAKOVA PAGE 40