Instruction Sheet SNE SERIES. Cable Chase

Transcription

1 Instruction Sheet SNE SERIES Cable Chase THANK YOU Thank you for purchasing the SNE Series Cable Chase. Please read these instructions thoroughly before installing this product. PRODUCT FEATURES The 45 RU high chase is available in 36, 42, and 48 depths Lever Lock compatible Brush top opening for cable passage Mounts at end of bay on left or right side I Rev -

2 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Clean only with dry cloth. Only use attachments/accessories specified by the manufacturer. WARNING: A WARNING ALERTS YOU TO A SITUATION THAT COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH. CAUTION: A CAUTION ALERTS YOU TO A SITUATION THAT MAY RESULT IN MINOR PERSONAL INJURY OR DAMAGE TO THE PRODUCT AND / OR PROPERTY. IMPORTANT WARNINGS AND CAUTIONS WARNING FAILURE TO READ, UNDERSTAND AND FOLLOW THE FOLLOWING INFORMATION CAN RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO THE EQUIPMENT OR VOIDING OF THE WARRANTY. IT IS THE RESPONSIBILITY OF THE INSTALLER/USER TO ENSURE THAT THIS PRODUCT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS. CAUTION SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. CAUTION FOR LOADING, ALWAYS PUT HEAVIER ITEMS AT THE BOTTOM OF THE UNIT, NOT NEAR THE TOP, IN ORDER TO HELP PREVENT THE POSSIBILITY OF THE FURNISHING TIPPING OVER. CAUTION THIS FURNISHING IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT SUPERVISION. CAUTION IF THERE IS VISIBLE DAMAGE ON THE PRODUCT IT MUST NOT BE INSTALLED / USED. Safety Instructions - Rack Mount A. Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. B. Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. C. Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. D. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuit might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E. Reliable Earthing - Reliable earthing of rack-mounting equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips). Page 2

3 SUPPLIED HARDWARE AND COMPONENTS Top Cable Bracket (2x) A #10 Flat Head Phil. Screw (4x) E Hex Bonding Nut (3x) H Hex Head Screw (4x) B Brush and Grommet Top C Square Nut (4x) D 5/16 Hex Head Bonding Screw (3x) G Leveling Foot (2x) F 5/16-18 Hex Cap Screw (3x) J LEVER LOCK BRACKET AND HARDWARE Lever Lock Bracket (2x) Bonding Wire K PEM Stud (4x) Cable Chase Hex Keps Nut (4x) 1/4 x 9 Hex T-Handle Wrench REQUIRED TOOLS #2 Phillips Head Screwdriver or Power Driver with Bit Flat Head Screwdriver 5/16 Socket Wrench 1/4 x 9 Hex T-Handle Wrench (Provided) Page 3

4 DISASSEMBLY OF SNE ENCLOSURE 1. Remove bonding wires from top panels. 2. Remove top panel and grommet top panel using a Phillips head screwdriver. 3. Remove bonding wire from top side cover on the side you wish to install the chase. Remove the top side cover using a 5/16 socket wrench. 4. Remove bonding cables and side panels from the side you wish to install the chase. NOTE: Set aside all bonding wires, panels, cover, square nuts, and screws for reinstallation. Top Panel Grommet Top Panel Top Side Cover Side Panels SNE Enclosure (Not Included) Page 4

5 INSTALLATION NOTE: While the cable chase appears upright for the steps on this page, you may prefer carefully placing the chase in a horizontal position on the floor while completing them. 1. Install one of the top cable brackets (A) to the enclosure using a 5/16 socket wrench and replace bonding wires and square nuts. 2. Reinstall top panel and grommet top panel to the enclosure using a Phillips head screwdriver and replace bonding wires. 3. Install the other top cable bracket (A) and the top side cover to the cable chase with (4) hex head screws (B) and a 5/16 socket wrench, as shown. 4. Install brush and grommet top (C) using (4) square nuts (D) and (4) #10 flat head Phillips screws (E) as shown. 5. If casters or leveling feet are installed on your enclosure, install (2) leveling feet (F) to outside holes as shown and adjust using a flat head screwdriver. Top Panel E Grommet Top Panel D C Top Side Cover A F Page 5

6 INSTALLATION (CONTINUED) 6. Attach Lever Lock brackets (if used) before securing the chase to your enclosure. Face the flanges outside. 7. Lever Lock brackets are typically installed on the sides joined together on the enclosure and the chase. For more information, refer to the SNE Series Lever Lock Bracket instruction sheet. Lever Lock Brackets Locations 1 and 2, top left and right sides (depending on which side you install the chase). Locations 3 and 4, bottom left and right sides (depending on which side you install the chase). Page 6

7 INSTALLATION (CONTINUED) 8a. For cable chase installation on the right (facing) of the enclosure, secure the rear of the chase to your enclosure by passing (3) bonding screws (G) passthrough holes toward the front of the enclosure and chase to (3) bonding nuts (H) using a 5/16 socket wrench. 8b. For left side installation, be sure to use passthrough holes toward the front of the chase and enclosre for your bonding screws (G) and nuts (H). Passthrough holes toward front of enclosure and chase H G Page 7

8 INSTALLATION (CONTINUED) 9a. For right side installation, secure the front of the cable chase to your enclosure by passing (3) hex cap screws (J) through passthrough holes toward the front of the enclosure into the rivnut holes toward the front of the chase with the 1/4 hex t-handle wrench provided. 9b. For left side installation, pass (3) hex cap screws (J) through passthrough holes toward the front of the chase into the rivnut holes toward the front of the enclosure instead. 10. Reinstall side panels to the outside of the cable chase. Passthrough hole toward front of enclosure (chase installation to right of enclosure) Rivnut hole toward front of chase (chase installation to right of enclosure) J Page 8

9 GROUNDING AND BONDING THE CHASE Protective Earth Terminals (PET) are located on the bottom frame of the enclosure. These terminals are marked with the symbol. Enclosure accessory parts contain or are provided with bonding points for connection to the frame / PET. Protective earth and bonding connections shall be in accordance with Article 250 of the National Electric Code. When removing any bonded accessory for servicing the enclosure, make sure to disconnect the bonding terminal from the accessory. NOTE: The bonding terminal MUST be reconnected to the accessory when the part is replaced after servicing. 1. Use existing bonding wires from the enclosure to connect the following side panel bonding point locations on your cable chase as shown. 2. Attach provided bonding wire (K) to the upper panel bonding point on the diagram. K Side Panel Bonding Point Upper Panel Bonding Point Bonding Point Bonding Point Side Panel Bonding Point Bonding Point Cross Section of Enclosure Shown for Clarity Page 9

10 WARRANTY Middle Atlantic Products (the "Company") warrants the product to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product. The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection thereof at the Company's factory. This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or maintenance. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY. Corporate Headquarters Corporate Voice Fax / International Voice Fax middleatlantic.com - info@middleatlantic.com Middle Atlantic Canada Voice Fax / middleatlantic.ca - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO Registered Company. Page 10