E instruments. MAXiCAL. ATEX Calibration Lab Multifunction Pressure and Temperature ATEX Calibrators

Transcription

1 E instruments MAXiCAL ATEX Calibration Lab 3000 MAXiCAL ATEX Multifunction Calibrators - Thermocouple - Resistance Thermometers - ma Loop with power supply - V, mv, Hz, Ohm Pneumatic Calibrator with built-in pump vacuum to 40 Bar Hydraulic Calibrator with built-in pump up to 700 Bar Low pressure Calibrator with built-in pump 160mBar Absolute Sensor 2 Bar HART Programmer Certificate of calibration The Atex Calibration laboratory includes all the instruments necessary for calibration on Intrinsically Safe Bulletin CAL KIT ATEX EN - ed Area. Multifunction calibrators with simultaneous dual channel for thermocouple, resistance thermometers, ma, V and Frequency. calibrators from low 160mBar up to Hydraulic 00 Bar. A fundamental tool for Oil&as and Petrolchemical Plant. Splash proof carrying cases will protect instruments during transport and stocking Features are related to all models equipped with full configuration. On next pages you can find specific details.

2 Intrinsically-Safe Multifunction Process Calibrator Simply powerful intrinsically-safe calibration tool Summary Specifcations: (18 C to 28 C for one year) Function Measure or Source Resolution Notes Voltage 0 to 0 mv 0 to V (Source) 0 to 30 V (Measure) 0.01 mv V V 0.02 % Rdg + 2 digits Max. Load 1 ma ma 0 to ma 0.02 % Rdg + 2 digits Max. Load ma mv (TC terminals) -.00 mv to mv 0.01 mv ± (0.025 % or range + 1 digits) Resistance 15 Ω to 3200 Ω (Source) 0 Ω to 3200 Ω (Measure) 0.1 Ω to 1 Ω 0.1 Ω to 1 Ω 0. Ω to 1.0 Ω 0. Ω to 1.0 Ω Frequency 2.0 to 00.0 CPM 1 to 00 Hz 1 to.0 khz 0.1 CPM 1 Hz 0.1 khz ± (0.05 % + 1 digit) ± (0.05 % + 1 digit) ± ( % + 1 digit) For frequency source waveform is 5 V p-p squarewave, -0.1 V offset Loop supply 12 V N/A % Temperature coeffcient: - C to 18 C, 28 C to 55 C, ±0.005% of range per C The multifunction IS calibrator is able to - calibrate almost any process instrument likely to need service in an ex-hazardous area. The device is a powerful, multifunction calibration solution that offers: Measure volts dc, ma, RTDs, thermocouples, frequency and ohms Source or simulate volts dc, ma, RTDs, thermocouples,frequency and ohms Two channel simultaneous source and measure capability for calibration of Power transmitters with internal loop supply Store frequently-used test setups for later use transmitters Standard delivery: Atex Calibrator Test leads Test clips one pair of stackable test leads ISO Traceable calibration certifcate batteries instruction manual Ex-data: Ex-designation: II 1 EEx ia IIB 171 C EC-Certificate of conformity: Kema 04 ATEX 130 I.S. Class 1 Div. 1 roups B-D, 171 C Thermocouple accuracy specifcations: RTD Type Measure (4 wire) Source Ni C to 0 C Pt C to 800 C 0.33 C 0.33 C Pt C to 630 C 0.3 C 0.3 C Pt C to 630 C 0.3 C 0.3 C Pt C to 250 C 250 C to 630 C Pt C to 500 C 0.3 C 0.3 C 500 C to 630 C 0.4 C 0.4 C Pt C to 0 C 0 C to 630 C Resolution RTD 0.1 C, 0.1 F Features: Simultaneous Function Capability Channel A Channel B ma DC M ma DC with loop supply M 0.00 mv DC V DC Measure M V DC Measure.000 V DC Source Source: 15 to 3200 Ω, Measure: 0 to 3200 Ω Thermocouple J, K, E, R, S, B, L, U, N RTD Ni120; Pt0 (392); Pt0 (JIS); Pt0, 200, 500,00 (385) Frequency; Squarewave, 1 CPM to khz; fxed amplitude 5V p-p M = Measure S = Source / Simulate Technical data: Maximum Voltage: Storage temperature: Operating temperature: Relative humidity: Dimensions (HxWxD): Weight: Power supply: Operating time: Thermocouple accuracy specifcations: Thermocouple Measure or source Resolution J, K, T, E, L, N, U B, R, S J -200 to 0 C 0 to 1200 C K -200 to 0 C 0 to 1370 C T -200 to 0 C 0 to 400 C E -200 to 0 C 0 to 950 C -20 to 0 C R 0 to 500 C 500 to 1750 C -20 to 0 C S 0 to 500 C 500 to 1750 C 600 to 800 C B 800 to 00 C 00 to 1800 C -200 to 0 C L 0 to 900 C -200 to 0 C U 0 to 400 C 200 to 0 C N 0 to 1300 C 30 V -40 C to 71 C C to 55 C 90 % ( to30 C); 75 % (30 to 40 C); 45 % (40 to 50 C); 35 % (50 to 55 C) 200 x 96 x 47 mm 650 g 4x AA, type approved 25 hours typical 1.0 C 0.7 C 1.2 C 1.2 C 0.9 C 0.7 C 2.5 C 1.8 C 1.4 C 2.5 C 1.8 C 1.5 C 2.2 C 1.8 C 1.4 C 0.85 C 0.7 C 1.1 C 0.75 C 1.5 C 0.9 C 0.1 C, 0.1 F 1 C, 1 F Notes specifcations include cold junction uncertainty.

3 OVERVIEW With advanced microprocessor technology and state-of-the-art silicon pressure sensors, the ConST211 series digital pressure gauges provide an accurate, reliable, and economic solution for wide range of pressure applications. They are loaded with functionality and remarkably easy to use. To reach the best performance, every silicon pressure sensor in gauges has been specially aged, tested and screened before assembly. ConST211 series digital pressure gauges are unmatched in performance and reliability. Best of all, they are surprisingly affordable. FEATURES 0.025% full scale accuracy (ConST ) 0.05% full scale accuracy (ConST ) 0.1% full scale accuracy (ConST 211-) 0.2% full scale accuracy (ConST ) ranges to 36,000 psi (2500 bar) Fully temperature compensated accuracy from 14 F to 122 F (- C to 50 C) Up to eleven selectable pressure units Large, easy to read display with 5-digit resolution Back lighted display % pressure indication with fan-shaped graph scale for visual reference Display flash warning when pressure over 120% of FS ATEX certified intrinsically safe (Model CONST 211 IS) NIM traceable calibration certificate (optional) 9V battery power or AC adapter (optional) EX II 1 Ex ia IIC T4 a APPLICATIONS Precision pressure measurement Field gauge calibration safety valve (PSV) testing regulator testing SPECIFICATIONS Model ConST 211: Regular gauge ConST 211 IS: ATEX certified intrinsically safe ConST 211(IS)-02: 0.025% of full scale ConST 211(IS)-05: 0.05% of full scale ConST 211(IS)-: 0.1% of full scale ConST 211(IS)-20: 0.2% of full scale (For detail accuracy, please see pressure range table) auge types auge pressure Compound Absolute pressure Differential pressure s V15 P2 P5 P P15 P30 P50 P0 P300 P500 P1K P3K P5K PK P15K P25K P30K P36K [2] Media (psi) (bar) [1] auge [3] [3] Note: [1]. Sealed gauge pressure for above 00 psi [2]. =as, L=Liquid [3] % FS for gas media only Permitted for Zone0,Equipment roup II,as roup IIC hazardous atmospheres,temperature class T4 This product conforms to the following standards: EN : 2009 EN : 2007 (% FS) 0.05 (0.1, 0.2) 2 X 2 X 1.5 X 1.5 X 1.5 X

4 AP5 AP AP15 AP30 AP50 AP0 AP300 AP500 AP1K AP3K AP5K DP1 DP2 DP5 DP DP20 DP30 CP2 CP5 CP CP15 CP30 (psi) (inh O) (psi) ±2 ±5 ± ±15-15 to 30 (bar) (mbar) (bar) ±0.16 ±0.35 ±0.7 ±1-1 to 2 Absolute Media Differential Media Compound Media (% FS) (% FS) (%FS) 0.05 (0.1, 0.2) 0 X 0 X 50 X 20 X 20 X 20 X Display Description: 5 full digit FSTN LCD Display rate: 3 readings per second (Default setting) Adjustable from readings per second to 1 reading every ten seconds Numeral display height: 16.5mm (0.65 ) Fan-shaped raph Scale Similar to analog dial, including pressure swing, % indication with fan-shaped graph scale for visual reference, low/high alarm Units 2 Pa, kpa, MPa, psi, bar, mbar, kgf/cm, inh2o, mmh2o, inhg, mmhg Environmental Compensated Temperature: 14 F to 122 F (- C to 50 C) Operating Temperature*: 14 F to 122 F (- C to 50 C) *0.025%FS accuracy guaranteed only over the ambient temperature range of 68 F to 79 F (20 C to C) Storage Temperature: -4 F to 158 F (-20 C to 70 C) Humidity: <95% Media Compatibility (0 30) psi: Clean dry non-corrosive gases (50 36,000) psi: media compatible with 316L SS Port,, 1 4 NPT( 15,000psi) Autoclave F-250-C, 9/16" - 18 UNF female or Autoclave M-250-C, 9/16"-18 UNF male (>15,000psi) inch (4mm) test hose (for differential pressure) Other connections available per request Power Battery: One 9V alkaline battery (included) Battery life: 300 hours ( readings/s), 600 hours (3 reading/s), or 6000 hours (1 reading/s) Power auto-off: 60 minutes power auto-off. Auto-off may be disable External power: 1/220V external power adapter (optional) (Do not use the external power adapter in a hazardous atmosphere) Enclosure Case material: Aluminum alloy Wetted parts: 316L SS Dimension: 120mm diameter X 40mm depth Weight: 0.6kg Intrinsic Safety and European Compliance CE marked ATEX certified intrinsically safe (ConST 211IS) Communication RS232 (Do not use the RS-232 connector in a hazardous atmosphere)

5 PS-700/PS-00 PS-40 The Eigroup PS pump series are a remarkable new range of hand pumps for generating vacuum, gas and hydraulic pressure from a few mbar up to 00 bar. The pumps are the ideal tool for applying test pressures to sensors, gauges, pressure switches and any pressure device. They are a low cost solution for field and workshop use and can be supplied with the wide range of Eigroup digital pressure indicators or for OEM applications. calibrate pressure device 4 separate models range from Vacuum to 00 bar extended kit solutions to suits different needs The pneumatic pumps allow pressures in excess of 600 psi to be generated with just a few strokes of the pump. By changing the push-in switching valve to vacuum, the pump will generate vacuum down to nearly 96%. The PS 700 and PS 00 hydraulic test pumps work with a variety of different fluids, including water and oil to easily generate pressures up to 00 bar (14500 psi). The pump uses an unique switch which allows for fast priming or filling of the test system and then switching as needed to a smaller stroke for easier generation at high pressure. The desired pressure point can be easy tuned by using the vernier control and a precision needle vent valve allows for controlled venting. All 4 pumps can be supplied as a bare pump or in kit form with a hard transit case, set of adaptors, seals and hose. PS-7 SELECTION UIDE Features PS-7 PS-40 PS-700 PS-00 Pneumatic pressure capability Vacuum capability Hydraulic capability Integral fine control for accurate set point adjustable stroke for over pressure safety Controlled pressure relief valve Priming operation Fluid compatible (not distilled water) Scissor action pump TECHNICAL SPECIFICATION Parameter PS-7-OEM PS-40-OEM PS-700-OEM PS-00-OEM Operating pressure range -850 mbar to 7 bar -960 mbar to 40 bar 0 to 700 bar 0 to 00 bar media air air liquid liquid Fine adjustment resolution 1 mbar 1 mbar to 0 mbar to 0 mbar Ref port pressure connection 1/8 NPT (F) 3/8 BSP (F) 3/8 BSP (F) 3/8 BSP (F) Ref port standard adaptor 1/4 BSP (F) 1/2 BSP (F) 3/8 BSP (F) 1/2 BSP (F) Test point pressure connection 1/4 BSP (F) 1/4 BSP (F) 1/4 BSP (F) 1/4 BSP (F) Hose extension 2 x 1 meter 1 x 1 meter option option Weight 250 g 5 g 1.6 Kg 1.6 Kg Specification are based on minimum volume PS-40 Pneumatic Test Kits Combined vacuum/pneumatic kit for pressure testing includes: PS-40-OEM pump Set of BSP or NPT adaptors (to be specified) Set of seals hose with 1/4 BSP F adaptor (1 meter) Robust ABS transit case with customised foam and cells PS-700/00 Hydraulic Test Kit Hydraulic test kit for high pressure testing includes: PS-700-OEM or PS-00-OEM pump Set of BSP or NPT adaptors HTH-00-1 high pressure hose, 1 meter PS700-A-14 adaptor for HTH-00 hose Set of seals PS700-TC Robust ABS transit case with customised foam and cells

6 WE ve OT AbILITy MFC 4150 HART ATEX Communicator MFC 4150 HART Communicator is the latest HART communicator from Meriam Process Technologies. HART feld devices can be confgured and trimmed using the MFC. The MFC is a full function HART Communicator with features that optimize commissioning, confguration and maintenance operations. MFC 4150 supports all HART devices at the Universal and Common Practice command levels plus a large and growing list of devices at the Device Specifc command level. View our feld device list by going to and selecting Resources / Download Center / Advantages The MFC ofers several unique features that provide HART users with a more useful, more reliable and more available communication tool. Just consider the MFC 4150 s features: Quick start up and connect: 15 seconds! Full alpha-numeric keypad 60 hours battery life (w/o backlight) Review / Edit on the fy Update new device profles and frmware from Meriam Quick Menu short cuts for commonly used commands via the Internet the MFC 4150 is never out of your hands HART menu Home key Clone / Upload / Download confgurations Dedicated text edit keys Of-line mode for editing / reviewing confgurations Programmable lock-out settings Document and store 200 confgurations Contrast key for direct adjustment in any mode As-found / As-left history with Meriam DMS software Elastic hand strap, adjustable shoulder strap and soft carrying case 13-line, 128 x 128 graphic, backlit display Left side thumb keys for one-handed navigation Dongle coordinates AC power adapter and serial communications Certifcations Intrinsically safe (approved AA alkaline batteries only) II 1 ; EEx ia IIC T4 Intrinsically safe, Exia Class I, Div. 1 roups A, B, C, D: T4 ATEX Distributed by :