DMS 700 Multichannel System

Transcription

1 DMS 700 Multichannel System Schematic & Part List 2-32 Channel 1

2 Introduction The following schematics will help you to easily set multi channel systems. Please use the equipment that is specified in the schematics only. For your convenience and understanding, we ve added technical information and part lists. You can use this part lists when ordering the system you require! If you need any help regarding the frequency regulations or if your particular situation doesn t allow for a standard system to be installed, please do not hesitate to contact us under sport@akg.com. All the DMS700 Systems in this document are designed with active antennas that can used in all venues with a 20m RG58 antenna cable. active directional antenna For Venues (tour sound &installs) that cover large distances ( to 100m, 330 ft) like music halls, stadiums and other open air applications. RA4000 B/W active omni-directional antenna For Venues without a designated transmitter area and to 100m/330 ft free line of sight. Ideal for conference rooms, multi purpose halls, houses of worship etc. 2

3 Content General Information Page Receiver/Antenna Placement Information 4 Squelch Information 4 Intermodulation Information 4 - HiQnet System Architect Information 5 Cable Attenuation Information 6 PS4000 dip switch Information 6 AB4000 dip switch Information 6 PS4000 dip Switch Matrix Information 7 Required Component Matrix Information 8 Glossar Information 9 WMS System Antenna Type Page 2Channel 2 Channel 4Channel 4Channel RA4000 B/W RA4000 B/W Schematic / Part List Schematic / Part List Schematic / Part List Schematic / Part List Channel Schematic / Part List 19 8Channel RA4000 B/W Schematic / Part List Channel 10 Channel RA4000 B/W Schematic / Part List Schematic / Part List Channel 12 Channel 16 Channel RA4000 B/W Schematic / Part List Schematic / Part List Schematic / Part List Channel RA4000 B/W Schematic / Part List Channel Schematic / Part List Channel RA4000 B/W Schematic / Part List Channel Schematic / Part List Channel RA4000 B/W Schematic / Part List Channel Schematic / Part List Channel RA4000 B/W Schematic / Part List Channel CU 700 System Schematic 47 3

4 Technical Information Wireless Basics Every wireless microphone system has to operate on one specific frequency Transmitter and receiver of a system need to work on the same frequency Two transmitters cannot be used with the same frequency at the same time Receiver/Antenna Placement Direct line of sight between transmitter and receiver antenna Place the receiver/antennas at least 5 ft. (1.5 m) away from all transmitters Place the receiver antennas at least 5 ft. (1.5 m) away from any big metal object, wire(particularly wire mesh) or sheet metal structures, walls, ceilings, etc. Do not place the antennas in hidden places (behind walls) Place the receiver at least 5 ft. (1.5 m) away from any equipment that may emit RF radiation such as lighting racks, fluorescent lamps, digital effect units, or PCs Squelch DMS 700 has a variable squelch level. This level depends on the RF-environment and is adjusted automaticaly in order to ensure best quality in the range of operating. The audio turns on only in the presence of an DMS700 transmitter with the correct encryption key and an adequate signal quality If received signal has a bad quality or can not decrypted the audio output is muted Intermodulation Intermodulation is the result of two or more signals of different frequencies being mixed together, forming additional signals that are not harmonic frequencies of either. By using more than one transmitter simultaneously at the same location, intermodulation happens in the receiver and/or transmitter. In your case this intermodulation products are generated in the bandwidth that you are using. To avoid intermodulating frequencies, we offer you pre-calculated frequencies as presets in the, SR450 and SR4500 receiver. Please, make sure that when setting a multi channel system, all your receivers are set to the same country preset (NAME) and gro. Use the Quickset function (Automatic set) to scan for intermodulation-free and clean frequencies at your venue. 4

5 HUB 4000 Q The HUB 4000 Q adds HiQnet functionality to an AKG wireless system (DSR 700, SR 4500, SST 4 and coming devices are sported). For large wireless systems multiple HUB 4000 Q s can be used and controlled from a single computer. With connecting the HUB 4000 Q to a HiQnet network the user is able to monitor and control an AKG wireless system from a computer running System Architect. HiQnet System Architect The simple and easy to use user interface of the HUB 4000 Q plug in within System Architect allows the user to set and configure the wireless system easy and fast with tools like Auto Set, Environment Scan, RF Monitor and Device Manager. HiQnet System Architect also allows custom configuration of custom made user interfaces which makes it a perfect tool for installed sound and tour sound applications. Today's HiQnet system is built from flagship products from Harman Pro brands AKG Acoustics, BSS Audio, Crown International, dbx Professional, JBL Professional, Lexicon Pro, Soundcraft and Studer. AKG User Interface Features automatic identification of all s Simple and easy to use channel-oriented user interface Fast and intuitive set and configuration of frequency management with 1-Click Set, Enviroment Scan and Device Manager Offline configuration Device Manager Frequency Management Save and load your set Enviroment Scan - Frequency Graph 5

6 Cable Attenuation To obtain the best sound possible, you need to have the right RF input level throughout your signal chain. Premium quality wireless systems like the DMS700, WMS450 and WMS4500, offer you adjustable RF-level settings that garantee to maximise operating distance even when using different cable lenghts and different types of cable! For this purpose, AKG s antenna splitter, has 3 dip switches that you ll find on the right side of it s front panel, behind the AKG logo. RG58 Cable Attenuation (MKPS, MKA5, antenna cable) PS4000 dip switch This dip switch reduce the input RF level of the PS4000 between 0 db and 14 db. All antenna output level and the cascade(link) output level have an effect on this reduction. Power Splitter Antenna A cascade output Rear View Antenna A input Ant. B 4x Antenna A output Signal level adjustment Attenuation dip switches behind AKG Logo AB4000 dip switch The AB4000 has a fix 17.5dB amplifier in the output stage. The dip switch reduce the input RF level of the AB4000 between 0 db and -14 db. AB4000 get the DC power through the antenna cable from the PS4000 or an ASU4000 unit. AB4000 Antenna Booster Internal Attenuation Total Gain 3.5 db 5.5 db 7.5 db 9.5 db 11.5 db 13.5 db 15.5 db 17.5 db Signal level adjustment 6

7 PS4000 dip switch matrix (RG58 cable) Passiv Antennas Active Antennas Cable type & Length Antenna type & Gain ¼ wave UHF Antenna 0 db RA4000 W SRA2 W RA4000 BW SRA2 BW 1 db 4-6 db 18 db db 0110E0189 1m / 3ft 0 db 0 db -4 db MKA 5 5m / 16ft 0 db 0 db -2 db -14 db MKA 20 20m / 66ft -8 db -12 db MKA 5 + MKA 20 25m / 82ft -6 db -10 db 2x MKA 20 40m / 132ft 0 db -2 db 3x MKA 20 60m / 198ft Antenna Booster AB4000 necessary! 4x MKA 20 80m / 264ft Antenna Booster AB4000 necessary! RA4000 BW 2x MKA 20 AB db 1x MKA 20 PS db RA4000 BW 2x MKA 20 AB db 2x MKA 20 PS db SRA2 BW 2x MKA 20 AB db 1x MKA 20 PS db SRA2 BW 2x MKA 20 AB db 2x MKA 20 PS db You have to use this PS4000 dip switch settings at all PS4000 with direct connection to the antennas. All cascade PS4000 have the same dip switch setting ON/ON/ON (0dB) 7

8 DMS700 Component Matrix Number of Standard Power Sply DMS Channel DMS Receiver PS4000 ZAPD-21 MKPS PSU4000 AC12 Power Sply Additional you will need min. 2x antennas and 2x MKAxx antenna cables! Please, look at the "PS4000 dip switch matrix (RG58)" to find your antenna components. 8

9 Glossar XLR CH1 ¼ TS CH1 DMS700 Stationary Receiver CASCADE A DC IN (12V/0.5A) Power Splitter 1:4 (Distribute RF signal and DC Power) Splits 1 antenna to 4 receiver Antenna cascade(link) output to send RF-Signal to next PS4000. Cascade max. 3 PS4000. If you need more than 12 channels use an ZAPD in front of the first PS4000. PSU4000 ~90-230V DC OUT 1 (2.5A) DC OUT 2 () DC OUT 3 () AC POWER PSU4000 Power Sply Unit with 3x 12 volt outputs (2.5A and ) Active Directional Antenna (21dB Gain) RA4000 B/W Active Omni-directional Antenna (18dB Gain) RA4000 B/W Charging Unit for DHT700 or DPT700 (2 transmitter / unit) S ZAPD-21 Passive Combiner 2:1 and 1:2 ZAPD-21 A B ANT IN ASU4000 ASU4000 Antenna Sply Unit DC IN (12V/0.5A) Splies to three active elements (RA4000BW, SRAW, AB4000) ANT IN AB4000 Antenna Booster AB4000 DEV1 DEV2 DEV3 DEV4 DEV5 DEV6 DEV7 DEV8 3.5 db 17.5 db amplifier DC IN (12V/0.5A) Network Concentrator for 8 devices (, SR4000, ETHERNET SR4500 or SST4) Cable Operate with Harman System Architect software - MKPS 0.65m/2 feet RG58 antenna cable MKA5 5m/16ft RG58 antenna cable 20/66ft RG58 antenna cable 0110E01890 Front assembly cable Install ¼ wave antennas at the front of the rack Front assembly cable & ¼ wave antenna 9

10 10

11 2 Channel DMS700 System With directional antennas & 40m antenna cable (132 feet) 2x (BNC I-connector is necessary to link cables!) 2x (BNC I-connector is necessary to link cables!) BNC I-connector Available e.g. Ordernumber BNC I-connector Available e.g. Ordernumber ANT IN ASU4000 DC IN (12V/0.5A) ANT IN ASU4000 DC IN (12V/0.5A) 2xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN 2 DHT700 or DPT700 charging system (optional) - Network Concentrator (optional) AC- Power Sply (1.) 1.0 Date Build document Revision Designer Wolfgang Fritz Project Ref.No. 2 channel DMS700 system ( Antennas) 11

12 2 Channel DMS700 System with directional antennas 1 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 ASU 4000 (BNC/none) 9 Antenna Sply unit for long antenna cables (BNC connector) without AC-Adapter 3009Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z MKA 20 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 1 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 12

13 2 Channel DMS700 System with omni-directional antennas & 25m antenna cable (82 feet) RA4000 B/W RA4000 B/W 1x + 1x MKA5 (BNC I-connector is necessary to link cables!) 1x + 1x MKA5 (BNC I-connector is necessary to link cables!) BNC I-connector Available e.g. Ordernumber BNC I-connector Available e.g. Ordernumber ANT IN ASU4000 DC IN (12V/0.5A) ANT IN ASU4000 DC IN (12V/0.5A) 2xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN 2 DHT700 or DPT700 charging system (optional) - Network Concentrator (optional) AC- Power Sply (1.) 1.0 Date Build document Revision Designer Wolfgang Fritz Project Ref.No. 2 channel DMS700 system (RA4000 B/W Antennas) 13

14 2 Channel DMS700 System with omni-directional antennas 1 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 ASU 4000 (BNC/none) 9 Antenna Sply unit for long antenna cables (BNC connector) without AC-Adapter 3009Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H MKA ft. (5m) Cables for connecting ext. antennas to multi-colers (2 req.) KOAX RG Z RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 1 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 14

15 4 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Rear View Signal level adjustment Attenuation Antenna A cascade output Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -12dB 2x (40m Cable) -2dB 4xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 4 DHT700 or DPT700 charging system (optional) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) 1.0 Build document Date Revision Designer Wolfgang Fritz Project Ref.No. 4 channel DMS700 system ( Antennas) 15

16 4 Channel DMS700 System with directional antennas 2 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 2 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 16

17 4 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -8dB 0dB 4xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 4 DHT700 or DPT700 charging system (optional) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) 1.0 Build document Date Revision Designer Wolfgang Fritz Project Ref.No. 4 channel DMS700 system (RA4000 B/W Antennas) 17

18 4 Channel DMS700 System with omni-directional antennas 2 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 2 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC 3258Z00.. Adapter 1 PSU Central Power sply unit for powering to 3 WMS 4000 HUB 4000 Q, CU 700, CU 4000 or 2997Z000 1 AC 12 3 to 12V 12 AC-Adapter WMS 4500receivers for 1 PS 4000, via PS ASU4000, Mains HUB Cable 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 18

19 8 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Rear View Signal level adjustment Attenuation Antenna A cascade output Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -12dB 2x (40m Cable) -2dB 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 8 DHT700 or DPT700 charging system (optional) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Build document Date Revision Designer Wolfgang Fritz Project Ref.No. 8 channel DMS700 system ( Antennas) 19

20 8 Channel DMS700 System with directional antennas 4 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 4 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 20

21 8 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Rear View Signal level adjustment Attenuation Antenna A cascade output Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -8dB 2x (40m Cable) 0dB 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 8 DHT700 or DPT700 charging system (optional) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Build document Date Revision Designer Wolfgang Fritz Project Ref.No. 8 channel DMS700 system (RA4000 B/W Antennas) 21

22 8 Channel DMS700 System with omni-directional antennas 4 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 4 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 22

23 10 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -12dB 2x (40m Cable) -2dB 10xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 10 DHT700 or DPT700 charging system (optional) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch - Network Concentrator (optional) DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Designer Wolfgang Fritz Project Build document Revision Ref.No. 10 channel DMS700 system ( Antennas) 23

24 10 Channel DMS700 System with directional antennas 5 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 5 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 24

25 10 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -8dB 2x (40m Cable) 0dB 10xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 10 DHT700 or DPT700 charging system (optional) AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch - Network Concentrator (optional) DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Designer Wolfgang Fritz Project Build document Revision Ref.No. 10 channel DMS700 system (RA4000 B/W Antennas) 25

26 10 Channel DMS700 System with omni-directional antennas 5 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 1 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 5 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 26

27 12 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -12dB -2dB 2xMKPS 0dB 8xMKPS 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 12 DHT700 or DPT700 charging system (optional) AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch - Network Concentrator (optional) DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Designer Wolfgang Fritz Project Build document Revision Ref.No. 12 channel DMS700 system ( Antennas) 27

28 12 Channel DMS700 System with directional antennas 6 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 6 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 28

29 12 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -8dB 0dB 2xMKPS 0dB 8xMKPS 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC 12 DHT700 or DPT700 charging system (optional) AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch - Network Concentrator (optional) DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Designer Wolfgang Fritz Project Build document Revision Ref.No. 12 channel DMS700 system (RA4000 B/W Antennas) 29

30 12 Channel DMS700 System with omni-directional antennas 6 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 6 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 30

31 16 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -12dB -2dB 2xMKPS 0dB 8xMKPS 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET 16 DHT700 or DPT700 charging system (optional) PC AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN CU Network Concentrator (optional) AC- Power Sply (1.) AC-CU4000 Power Sply (1.) 1.0 Build document AC- Power Sply (1.) AC- Power Sply (1.) Date Revision Designer Wolfgang Fritz Ref.No. AC- Power Sply (1.) AC- Power Sply (1.) Project 16 channel DMS700 system ( Antennas) 31

32 16 Channel DMS700 System with directional antennas 8 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 8 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 32

33 16 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -8dB 0dB 2xMKPS 0dB 8xMKPS 8xMKPS DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET 16 DHT700 or DPT700 charging system (optional) PC AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN CU Network Concentrator (optional) AC- Power Sply (1.) AC-CU4000 Power Sply (1.) 1.0 Build document AC- Power Sply (1.) AC- Power Sply (1.) Date Revision Designer Wolfgang Fritz Ref.No. AC- Power Sply (1.) AC- Power Sply (1.) Project 16 channel DMS700 system (RA4000 B/W Antennas) 33

34 16 Channel DMS700 System with omni-directional antennas 8 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 8 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 34

35 18 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -12dB -2dB 2xMKPS 0dB 2xMKPS 8xMKPS 8xMKPS XLR CH1 ¼ TS CH1 XLR CH2 ¼ TS CH2 XLR CH1 ¼ TS CH1 XLR CH2 ¼ TS CH2 18 DHT700 or DPT700 charging system (optional) AC- Power Sply (1.) AC- Power Sply (1.) DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN PC AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Build document Revision Designer Wolfgang Fritz Ref.No. AC- Power Sply (1.) Project 18 channel DMS700 system ( Antennas) 35

36 18 Channel DMS700 System with directional antennas 9 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 9 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 36

37 18 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x 2x (20m Cable) (40m Cable) -8dB 0dB 2xMKPS 0dB 2xMKPS 8xMKPS 8xMKPS 18 DHT700 or DPT700 charging system (optional) DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Build document AC- Power Sply (1.) AC- Power Sply (1.) Date Revision Designer Wolfgang Fritz Ref.No. AC- Power Sply (1.) Project 18 channel DMS700 system (RA4000 B/W Antennas) 37

38 18 Channel DMS700 System with omni-directional antennas 9 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 2 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 9 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 38

39 24 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -12dB 2x (40m Cable) -2dB 2xMKPS 0dB 2xMKPS 0dB 8xMKPS 8xMKPS 8xMKPS XLR CH1 ¼ TS CH1 XLR CH2 ¼ TS CH2 24 DHT700 or DPT700 charging system (optional) DEV8 DEV7 DEV6 DEV5 DC IN (12V/0.5A) DEV4 DEV3 DEV2 DEV1 ETHERNET DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Build document Revision AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) Designer Wolfgang Fritz Project Ref.No. 24 channel DMS700 system ( Antennas) 39

40 24 Channel DMS700 System with directional antennas 12 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 3 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 12 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 40

41 24 Channel DMS700 System with omni-directional antennas & 20(40)m antenna cable (66 or 132 feet) RA4000 B/W RA4000 B/W Power Splitter Antenna A cascade output Rear View Signal level adjustment Attenuation Antenna A input Ant. B 4x Antenna A output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber dip switches behind AKG Logo 1x (20m Cable) -8dB 2x (40m Cable) 0dB 2xMKPS 0dB 2xMKPS 0dB 8xMKPS 8xMKPS 8xMKPS XLR CH1 ¼ TS CH1 XLR CH2 ¼ TS CH2 DEV8 DEV7 DEV6 DEV5 DC IN (12V/0.5A) 24 DHT700 or DPT700 charging system (optional) DEV4 DEV3 DEV2 DEV1 ETHERNET DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC AC- Power Sply (1.) AC- Power Sply (1.) DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch DC IN AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) - Network Concentrator (optional) AC- Power Sply (1.) AC- Power Sply (1.) 1.0 Date Build document Revision AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) AC- Power Sply (1.) Designer Wolfgang Fritz Project Ref.No. 24 channel DMS700 system (RA4000 B/W Antennas) 41

42 24 Channel DMS700 System with omni-directional antennas 12 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 3 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H RA 4000 B/W 23 External omni-directional active dipoleantenna with amplifier (2 req.) 2632Z0030 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 12 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC Adapter 3258Z HUB 4000 Q / none 13 Network concentrator without AC-Adapter; of 8 systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 42

43 32 Channel DMS700 System with directional antennas & 20(40)m antenna cable (66 or 132 feet) Power Splitter Rear View Signal level adjustment Attenuation Antenna A cascade output 40m / 132 ft Version: 2x BNC I-connector is necessary to link cables! Available e.g. Ordernumber Antenna A input Ant. B 4x Antenna A output ~90-230V PSU4000 DC OUT 1 (2.5A) DC OUT 2 () AC POWER DC OUT 3 () To No.1 To No.2 To DC IN dip switches behind AKG Logo ~90-230V PSU4000 DC OUT 1 (2.5A) DC OUT 2 () AC POWER DC OUT 3 () To No.3 To No.4 To DC IN S ZAPD-21 A B S ZAPD-21 A B 4xMKPS 1x (20m Cable) -8dB 2x (40m Cable) 0dB 2xMKPS 0dB 1x 2x (20m Cable) (40m Cable) -8dB 0dB 2xMKPS 0dB xMKPS 8xMKPS 8xMKPS 8xMKPS XLR CH1 ¼ TS CH1 XLR CH2 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 ¼ TS CH2 DC IN (12V/0.5A) ETHERNET XLR CH1 ¼ TS CH1 XLR CH2 ¼ TS CH2 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DC IN (12V/0.5A) ETHERNET PC DEV 8 DEV 7 DEV 6 DEV 5 DEV 4 DEV 3 DEV 2 DEV 1 DHCP Switch - Network Concentrator (optional) DC IN 1.0 Date Build document Revision Designer Wolfgang Fritz Project Ref.No. 32 channel DMS700 system ( Antennas) 43

44 32 Channel DMS700 System with directional antennas 16 DSR "-rack receiver, internal power sply; (frequency range to MHz or to MHz ); 2 UHF antennas; 1 IEC cable US, 1 IEC cable EU 3255Z DHT 700 or DPT Hand-held transmitter or Bodypack transmitter; (frequency range to MHz or to MHz ); stand adapter or belt clip; 2 AA size dry batteries, Colour Coding Kit and 3256Z Z00.. Windscreen 4 PS 4000W 18 Wide band antenna multi coler (4+1 out) without AC-Adapter 2996Z ZAPD21 30 passive power combiner (2in 1out) or Splitter (1in 2out) SERVSON76 40 MK PS 15 Connecting cable for PS to SR 2.15ft (65cm) 6000H SRA 2 B/W 25 External directional active "paddle" antenna with amplifier (2 req.) 3009Z0001 Additional parts for 40m(132feet) Antenna Cable 2 BNC I-connector EXTERNAL!! Not available at AKG - BNC I-Connector (you can buy it at Ordernumber ) Optional Components (Charging System & PC Control System) 16 CU Twin charger + 2 AA size rechargeable batteries for DHT 700 or DPT 700 transmitter; with AC 3258Z00.. Adapter 5 PSU Central Power sply unit for powering to 3 WMS 4000 HUB 4000 Q, CU 700, CU 4000 or 2997Z000 2 HUB 4000 Q / none 13 to Network 12 WMS concentrator 4500receivers without via AC-Adapter; PS 4000, Mains of 8 Cable systems 2955Z AC V AC-Adapter for 1 PS 4000, ASU4000, HUB 4000 Q or SR H000 1 DHCP Net Switch + CAT5 Cable EXTERNAL!! Not available at AKG - for 4 input to 1 output (e.g. D-Link) Do not forget microphone head, headset or other microphone!! DPT 700: e.g. C555L, C520ML, C516ML, C518ML, C519ML, HC577 WR-L, CK77 WR-L, CK55L, C411L, C417L 44