Telecommunications Recommendation extension "A" SPECIFICATION FOR COMMON CHANNEL SIGNALLING SYSTEM No. 7. Message Transfer Part /MTP/
|
|
- Katherine Singleton
- 5 years ago
- Views:
Transcription
1 Telecommunications Recommendation extension "A" SPECIFICATION FOR COMMON CHANNEL SIGNALLING SYSTEM No. 7 Message Transfer Part /MTP/ ISSUE
2 References References: -CCITT Blue Book Recommendation Q.701 Functional Description of MTP. -CCITT Blue Book Recommendation Q.702 Signalling data link. -CCITT Blue Book Recommendation Q.703 Signalling link. - CCITT Blue Book Recommendation Q.704 Signalling network functions and messages. - CCITT Blue Book Recommendation Q.705 Signalling network structure. -CCITT Blue Book Recommendation Q.706 Message Transfer Part Signalling Performance -CCITT Blue Book Recommendation Q.707 Testing and maintenance. -ETSI Specifications ETS (December 1991) Message Transfer Part (MTP) to support international interconnection. A 2 / 62
3 General Contents General...6 Functional description of MTP (Q.701) Introduction Signalling system structure Message transfer part and the signalling network Message transfer capability Differences from the Blue Book Compatibility in the message transfer part Interworking of Yellow, Red and Blue MTP implementations Primitives and Parameters of the Message Transfer Part...13 Signalling data link (Q.702) General Signalling bit rate Error characteristic and availability Interface specification points Digital signalling data link Analogue signalling data link...17 Signalling link (Q.703) General Basic signal unit format Signal unit delimitation Acceptance procedure Basic error correction method Error correction by preventive cyclic retransmission Initial alignment procedure Processor outage Level 2 flow control Signalling link error monitoring Level 2 codes and priorities State transition diagrams and timers...26 Signalling network functions (Q.704) Introduction Signalling message handling Signalling network management Signalling traffic management Changeover Changeback Forced rerouting Controlled rerouting Signalling point restart Management inhibiting...45 A 3 / 62
4 General 11 Signalling traffic flow control Signalling link management Signalling route management Common characteristic of message signal unit formats Formats and codes of signalling network management messages State transition diagrams...53 Signalling network structure (Q.705)...56 Message Transfer Part Signalling Performance (Q.706)...58 Testing and maintenance requirements (Q.707) General Testing Fault location Signalling network monitoring Formats and codes of signalling network testing and maintenance messages State transition diagrams...61 Document history...62 A 4 / 62
5 General CHAPTER 1 A 5 / 62
6 General General This document describes the technical requirement of Message Transfer Part of Signalling System No.7 to be applied in Signalling Points SP and Signalling Transfer Points STP implemented in the International Gateway Exchanges IGW (MTP-I) and the local and transit exchanges of the national telecommunications network (MTP-N). The differences are marked with MTP-I and MTP- N respectively. This document is based on CCITT Recommendations Q.701-Q.704 and Q.707 issued in the Blue Book and some of the requirements in ETS are also applied. This document is structured as an "Exceptions and Clarifications" specification which is intended to give a clear description of the alteration from the base documents. The specifications are written in English in order to align the description as close as possible to the terminology used in CCITT Recommendations and ETSI Standards. A 6 / 62
7 Functional description of MTP (Q.701) CHAPTER 2 Functional Description of MTP (Q.701) A 7 / 62
8 Functional description of MTP (Q.701) Functional description of MTP (Q.701) 1 Introduction 1.1 General 1.2 Objectives 1.3 General characteristic Method of description Primitives Peer-to-peer communication Contents of Recommendations Q.701 to Q.707 Series relating to the MTP 2 Signalling system structure 2.1 Basic functional division 2.2 Functional levels General Signalling data link functions (level 1) Note: Analogue signalling data links are not applied. A 8 / 62
9 Functional description of MTP (Q.701) The digital signalling channels are derived from the 2048 kbit/s digital path. Lower bit rates than 64-kbit/s are not applied Signalling link functions (level 2) Signalling network functions (level 3) User Part functions (level 4) 2.3 Signalling message 2.4 Functional interface 3 Message transfer part and the signalling network 3.1 General Signalling network components Signalling modes Signalling point modes Message labelling Note: The standard routing label shall apply for both international and national applications. 3.2 Signalling message handling functions A 9 / 62
10 Functional description of MTP (Q.701) Message routing Message distribution Message discrimination 3.3 Signalling network management functions Signalling traffic management Signalling link management The basic set of signalling link management procedures shall apply. Optional alternative sets (automatic reconfiguration of terminal devices and signalling data links) shall not apply Signalling route management 3.4 Testing and maintenance functions 3.5 Use of the signalling network Signalling network structure Provision of signalling facilities Application of signalling network functions 4 Message transfer capability A 10 / 62
11 4.1 General Functional description of MTP (Q.701) 4.2 User location in system structure 4.3 Message content Code transparency Service information Message label Message length 4.4 User accessibility Both associated and quasi-associated signalling modes shall apply. 4.5 Transport service performance Message transfer delay Message transfer failures 5 Differences from the Blue Book 5.1 Processor outage 5.2 Availability of adjacent signalling point A 11 / 62
12 Functional description of MTP (Q.701) 5.3 Handling of level 3 messages 5.4 Transferred controlled messages 5.5 Load balancing during changeback 5.6 Time-controlled changeover procedure 5.7 Changeback 5.8 MTP restart 5.9 Signalling traffic flow control 5.10 User part availability control 5.11 Signalling route management 6 Compatibility in the message transfer part 6.1 Unreasonable Information Messages containing an unallocated SIO value Messages containing an unallocated H0/H1 code A 12 / 62
13 Functional description of MTP (Q.701) Messages containing an unallocated value in a recognised field 6.2 Treatment of spare fields 6.3 Lack of acknowledgement 7 Interworking of Yellow, Red and Blue MTP implementations Shall apply 8 Primitives and Parameters of the Message Transfer Part 8.1 Transfer 8.2 Pause 8.3 Resume 8.4 Status Note: National options concerned with congestion handling shall not apply. 8.5 Restart A 13 / 62
14 Signalling data link (Q.702) CHAPTER 3 Signalling Data Link (Q.702) A 14 / 62
15 Signalling data link (Q.702) Signalling data link (Q.702) 1 General 1.1 A signalling data link is Functional configuration of... Note: Analogue signalling data links are not applied. 1.3 A digital signalling data link is... Note: The digital signalling channels are derived from the 2048 kbit/s digital path. 1.4 An analogue signalling data link is... Analogue signalling links are not applied. 1.5 Signalling System No.7 is capable of The operational signalling data link Equipment such as echo suppressors kbit/s digital signalling channels... 2 Signalling bit rate 2.1 General The standard bit rate on a digital bearer... A 15 / 62
16 Signalling data link (Q.702) Lower bit rates may be adopted... Lower bit rates are not applied The minimum signalling bit rate... Lower bit rates than 64-kbit/s shall not apply. 2.2 Use of bit rates lower than 64 kbit/s For national telephone call control Signalling System No The possible use of... 3 Error characteristic and availability 4 Interface specification points 4.1 Interface requirements may be... Interface specification point C shall apply. 4.2 For the international application... Interface specification point C shall apply. 4.3 Interface requirements for an international digital Interface requirements for an international analogue Interface at point A may or... A 16 / 62
17 Signalling data link (Q.702) 4.6 Implementations which do not follow all the requirements... 5 Digital signalling data link 5.1 Signalling data link derived from the 2048-kbit/s Signalling data link derived from the 8448-kbit/s Signalling data link derived from the 1544 kbit/s Signalling data link established over a digital path made up by digital sections based on different digital hierarchies 5.5 Signalling data link established over data circuits 6 Analogue signalling data link A 17 / 62
18 Signalling link (Q.703) CHAPTER 4 Signalling link (Q.703) A 18 / 62
19 Signalling link (Q.703) Signalling link (Q.703) 1 General 1.1 Introduction This Recommendation describes The signalling link functions Signal unit delimitation and alignment 1.3 Error detection 1.4 Error correction Two forms of error correction The basic method is a non compelled The preventive cyclic retransmission method Initial alignment 1.6 Signalling link error monitoring 1.7 Link state control functions 1.8 Flow control A 19 / 62
20 Signalling link (Q.703) 2 Basic signal unit format 2.1 General 2.2 Signal unit format 2.3 Function and codes of the signal unit fields General Flag Length indicator Service information octet Note: Messages with different priorities are not applied Sequence numbering Indicator bits Check bits Signalling information field Status field A 20 / 62
21 Signalling link (Q.703) Spare fields 2.4 Order of bit transmission 3 Signal unit delimitation 3.1 Flags 3.2 Zero insertion and deletion 4 Acceptance procedure 4.1 Acceptance of alignment A flag which is not followed If seven or more consecutive After deletion of the When the "octet counting" mode is... Shall apply 4.2 Error detection 5 Basic error correction method 5.1 General A 21 / 62
22 Signalling link (Q.703) 5.2 Acknowledgements (positive and negative acknowledgement) Sequence numbering Signal unit sequence control Positive acknowledgement Negative acknowledgement 5.3 Retransmission Response to a positive acknowledgement Response to a negative acknowledgement Repetition of message signal units 6 Error correction by preventive cyclic retransmission 6.1 General 6.2 Acknowledgements Sequence numbering Signal unit sequence control A 22 / 62
23 Signalling link (Q.703) Positive acknowledgement 6.3 Preventive cyclic retransmission Response to a positive acknowledgement Preventive cyclic retransmission procedure 6.4 Forced retransmission Forced retransmission procedure Limitation of the values N1 and N2 7 Initial alignment procedure 7.1 General 7.2 Initial alignment status indications 7.3 Initial alignment procedure 7.4 Proving periods 8 Processor outage A 23 / 62
24 Signalling link (Q.703) 9 Level 2 flow control 9.1 General 9.2 Detection of congestion 9.3 Procedure in the congestion situation 9.4 Congestion abatement procedure 10 Signalling link error monitoring 10.1 General 10.2 Signal unit error rate monitor The signal unit error rate monitor has The signal unit error rate monitor may In the "octet counting" mode When the link is brought into service The values of the three parameters... Only parameters for 64 kbit/s shall be applicable. A 24 / 62
25 Signalling link (Q.703) In the case where only random Alignment error rate monitor The alignment error rate monitor The counter is started from zero When the counter reaches a threshold The values of the four parameters Level 2 codes and priorities 11.1 Link status signal unit The link status signal unit The format of the one octet The use of link status indications Transmission priorities within level Five different items can be For the basic error correction method For the preventive cyclic retransmission... A 25 / 62
26 Signalling link (Q.703) 12 State transition diagrams and timers 12.1 Sections 12 contains the description of... Shall apply with regard to the relevant level 2 functions Timers (Bit rate of 64 kbit/s) T1 "Alignment ready" sec T2 "Not aligned" sec T3 "Aligned" 1-2 sec T4 "Proving period" normal sec "Proving period" emergency sec T5 "Sending SIB" sec T6 "Remote congestion" 3-6 sec T7 "Excessive delay of ack." sec A 26 / 62
27 Signalling network functions (Q.704) CHAPTER 5 Signalling network functions (Q.704) A 27 / 62
28 Signalling network functions (Q.704) 1 Introduction Signalling network functions (Q.704) 1.1 General characteristics of the signalling network functions This Recommendation describes the functions According to these principles Signalling message handling The purpose of the signalling message handling The signalling message handling functions As illustrated in Figure 1/Q.704, the signalling Signalling network management The purpose of the signalling network management As illustrated in Figure 1/Q.704, the signalling to 11 specify the procedures... Note: Signalling point restart procedure and national options in signalling traffic flow control procedure shall not apply The different procedures pertaining... Note: Only the basic signalling link management functions of 12 shall apply. A 28 / 62
29 Signalling network functions (Q.704) The different procedures pertaining... Note: National options (transfer restricted and signalling- route-set congestion-test procedures) shall not apply The format characteristic, common to Labelling, formatting and coding The description of signalling network... Shall apply with regard to the applicable level 3 functions. 2 Signalling message handling 2.1 General Signalling message handling comprises When a message comes from level When a message comes from level In the case that the message is destined to Message routing, discrimination and distribution The position and coding of service indicator In addition to the normal signalling message handling... A 29 / 62
30 Signalling network functions (Q.704) 2.2 Routing label The label contained in a signalling message... Note: The standard routing label applies also for the national application The standard routing label has a length The destination point code (DPC) indicates The signalling link selection (SLS) field Form the rule stated in above The above principles should also apply... The standard label structure shall apply. 2.3 Message routing function The message routing functions based Two basic cases of load sharing The routing information mentioned in See also notes in 3 and Handling of level 3 messages Messages not related to a signalling link Messages related to a signalling link... A 30 / 62
31 Signalling network functions (Q.704) Handling of messages under signalling link congestion Note: Both MTP-N and MTP-I shall apply the same congestion handling procedures In the international signalling network... Note: Congestion priorities shall not apply In national signalling networks using multiple congestion priorities 2.4 Message discrimination and distribution functions The routing criteria and load sharing method If the destination point code of the message... Note: The MTP-STATUS primitive is applied for the indication of the signalling network congestion In the case of a signalling point... Note: Different label structures are not used. 3 Signalling network management 3.1 General The signalling network management functions provide The occurrence of, or recovery from failures or... Note: Signalling route restricted state shall not apply. A 31 / 62
32 3.1.3 Whenever a change in the status of a signalling link... Signalling network functions (Q.704) Note: Signalling point restart, automatic allocation of signalling terminals and signalling data links, transfer restricted and signalling-route-set-congestion-test procedures shall not apply An overview of the use of the procedures Status of signalling links A signalling link is always considered by level Signalling link failure Signalling link restoration Signalling link deactivation Signalling link activation Signalling link blocking Signalling link unblocking Signalling link inhibiting Signalling link uninhibiting 3.3 Procedures used in connection with link status changes A 32 / 62
33 Signalling network functions (Q.704) Signalling link failed Signalling traffic management Signalling link management Signalling route management:... Note: Signalling route restricted state shall not apply Signalling link restored Signalling traffic management Signalling link management:... All available signalling links shall be active. When an unavailable signalling link has been made available, it has to be activated immediately Signalling route management Signalling link deactivated Signalling traffic management Signalling link management:... All available signalling links shall be active Signalling route management Signalling link activated Signalling traffic management... A 33 / 62
34 Signalling network functions (Q.704) Signalling link management:... All available signalling links shall be active Signalling route management Signalling link blocked Signalling traffic management:... Note: The national option shall not apply Signalling route management... Note: Signalling route set restricted state and transfer restricted procedures shall not apply Signalling link unblocked Signalling traffic management Signalling route management Signalling link inhibited Signalling traffic management Signalling link management... All available signalling links shall be active Signalling link uninhibited Signalling traffic management Signalling link management... All available signalling links shall be active. A 34 / 62
35 Signalling network functions (Q.704) Signalling route management Status of signalling routes Note: Signalling route restricted state shall not apply Signalling route unavailability Signalling route availability Signalling route restricted 3.5 Procedures used in connection with route status changes Signalling route unavailable Signalling traffic management Signalling route management Signalling route available Signalling traffic management Signalling route management Signalling route restricted 3.6 Status of signalling points A 35 / 62
36 Signalling network functions (Q.704) Signalling point unavailability Unavailability of a signalling point itself Unavailability of an adjacent signalling point... A 36 / 62
37 Signalling network functions (Q.704) Signalling point availability Availability of a signalling point itself Availability of an adjacent signalling point... Note: Transfer restricted message shall not apply. 3.7 Procedures used in connection with point status changes Signalling point unavailable Signalling point available Signalling traffic management... The signalling point restart procedure shall not apply Signalling link management... The signalling link restoration procedure shall apply. The signalling point restart procedure shall not apply Signalling route management... The transfer prohibited procedure shall apply. The transfer restricted and the signalling point restart procedures shall not apply Signalling point congested Signalling network congestion General Congestion status of signalling links When predetermined levels of MSU fill in the... A 37 / 62
38 Signalling network functions (Q.704) Note: For MTP-N also one congestion onset and one congestion abatement threshold shall be provided. National options (message priorities and multiple congestion threshold) shall not apply In national signalling networks with multiple... Shall not apply In national signalling networks using multiple Procedures used in connection with link congestion status changes Congestion states of signalling route sets a) b) c) Procedures used in connection with route set congestion status changes Signalling traffic management Signalling route management... 4 Signalling traffic management 4.1 General The signalling traffic management function The diversion of traffic in the cases of... Note: Signalling route restricted state and signalling point restart procedure shall not apply The signalling traffic flow control procedures... A 38 / 62
39 Signalling network functions (Q.704) 4.2 Normal routing situation Signalling traffic to be sent to... Notes: All available signalling links shall be active. Priorities between signalling links in a link set shall not apply Message routing (normal as well as alternative) Signalling link unavailability When signalling link becomes unavailable In the case when there is one or more alternative In the case when there is no alternative Signalling link availability When previously unavailable signalling link In the case when the link set, to which In the case when the link set (combined link set) Signalling route unavailability 4.6 Signalling route availability A 39 / 62
40 4.7 Signalling route restriction Signalling network functions (Q.704) 4.8 Signalling point availability 5 Changeover 5.1 General The objective of the changeover procedure Changeover includes the procedures to be used Network configurations for changeover Signalling traffic diverted from an unavailable As result of these arrangements, and of the message Changeover initiation and actions Changeover is initiated at a signalling point In the case when there is no traffic to transfer If no alternative signalling link exist In some cases of failures or in some network Buffer updating procedure A 40 / 62
41 5.4.1 When a decision to changeover is made... Signalling network functions (Q.704) The changeover order and changeover acknowledgement Upon reception of a changeover order or Retrieval and diversion of traffic 5.6 Emergency changeover procedures Due to the failure in a signalling terminal Time controlled changeover is initiated when Due to failures, it may be impossible for Procedures in abnormal conditions The procedures described in this section allow If no changeover message in response to If a changeover order or acknowledgement containing If a changeover acknowledgement is received If a changeover order is received without... A 41 / 62
42 Signalling network functions (Q.704) 6 Changeback 6.1 General The objective of the changeback procedure Changeback includes the basic procedures to be used Changeback initiation and actions Changeback is initiated at a signalling point... a) b) i) ii) iii) In the case when there is no traffic to transfer In the case that the signalling link made... Note: The transfer restricted procedure shall not apply In the case that the signalling link made If the signalling point at the far end of the link... Note: Signalling Point Restart procedure shall not apply. A 42 / 62
43 6.3 Sequence control procedure Signalling network functions (Q.704) When a decision is made at a given signalling point The concerned signalling point will restart The changeback declaration and changeback A particular configuration of the changeback code In the case that a signalling point ends Time controlled diversion procedure Note: Time controlled diversion procedure not applied concerning signalling point restart. The procedure shall apply in cases of controlled rerouting and changeback from another linkset The time controlled diversion procedure... Note: Signalling Point Restart procedure shall not apply When changeback is initiated after the... Note: Signalling Point Restart procedure shall not apply. 6.5 Procedures in abnormal conditions If a changeback acknowledgement is received If a changeback declaration is received after If no changeback acknowledgement is received... A 43 / 62
44 Signalling network functions (Q.704) 7 Forced rerouting 7.1 General The objective of the forced rerouting procedure Forced rerouting is the basic procedure Forced rerouting initiation and actions Forced rerouting is initiated at a signalling point In the case when there is no signalling traffic If no alternative route exist for signalling traffic... 8 Controlled rerouting 8.1 General The objective of the controlled rerouting procedure Controlled rerouting is the basic procedure... a) b) 8.2 Controlled rerouting initiations and actions Controlled rerouting is initiated at a signalling... Note: Actions in connection with the transfer restricted procedure shall not apply. A 44 / 62
45 8.2.2 In the case when there is no signalling traffic... Signalling network functions (Q.704) If the destination was inaccessible or restricted... Note: Transfer restricted procedure shall not apply. 9 Signalling point restart 10 Management inhibiting 10.1 General 10.2 Inhibiting initiation and actions 10.3 Uninhibiting initiation and actions Management-initiated uninhibiting Signalling routing control initiated uninhibiting 10.4 Receipt of unexpected management inhibition messages 10.5 Management inhibited link status and processor recovery 10.6 Inhibit test procedure A 45 / 62
46 Signalling network functions (Q.704) A local inhibit test is performed when A remote inhibit test is performed when Signalling traffic flow control 11.1 General 11.2 Flow control indications Signalling route set unavailability Signalling route set availability Signalling route set congestion (International signalling network) When the congestion status of a signalling After the reception of a transfer controlled When the status of a signalling route set Signalling route set congestion (National option with congestion priorities) Signalling route set congestion (National option without congestion priorities) Signalling point/signalling transfer point congestion A 46 / 62
47 Signalling network functions (Q.704) MTP user flow control User part congestion 12 Signalling link management 12.1 General The signalling link management function is used... The basic set of signalling link management procedures shall apply. Optional alternative sets shall not apply A signalling link set consist of one or more... The basic set of signalling management procedures shall apply. The automatic allocation of signalling terminals and signalling data links shall not apply When a link set is to be brought into service... a) b) c) 12.2 Basic signalling link management procedures Signalling link activation In the absence of failures, a link set contains... All signalling links in the link set shall be active in the absence of failures When a decision is taken to activate an Signalling link restoration Signalling link deactivation A 47 / 62
48 Signalling network functions (Q.704) Link set activation Link set normal activation Link set emergency restart Time out values 12.3 Signalling link management procedures based on automatic allocation of signalling terminal 12.4 Signalling link management procedures based on automatic allocation of signalling data links and signalling terminals 12.5 Automatic allocation of signalling terminals According the 4.4 of ETS , these procedures shall not apply Automatic allocation of signalling data links 12.7 Different signalling link management procedures at the two ends of a link set Note: The basic set of signalling management functions shall apply. 13 Signalling route management 13.1 General A 48 / 62
49 National options shall not apply. Signalling network functions (Q.704) 13.2 Transfer prohibited The transfer-prohibited procedure is performed A transfer-prohibited message relating to... i) ii) iii) iv) v) Note: Signalling point restart procedure shall not apply When a signalling point receives a transfer-prohibited In some circumstances it may happen that Transfer allowed The transfer-allowed procedure is performed A transfer-allowed message relating to When a signalling point receives a In some circumstances it may happen Transfer-restricted (National option) 13.5 Signalling-route-set-test A 49 / 62
50 Signalling network functions (Q.704) The signalling-route-set-test procedure is A signalling-route-set-test message is sent from... The transfer-restricted procedure shall not apply A signalling-route-set-test message is sent to At the reception of a signalling-route-set-test... The transfer-restricted procedure shall not apply At the reception of the transfer-prohibited Transfer controlled (International network) Shall apply for both MTP-I and MTP-N Transfer controlled (National option with congestion priorities) 13.8 Transfer controlled (National option without congestion priorities) 13.9 Signalling-route-set-congestion-test (National option) 14 Common characteristic of message signal unit formats 14.1 General 14.2 Service information octet A 50 / 62
51 Service indicator Signalling network functions (Q.704) National options shall not apply Subservice field Additional User Parts and message priorities are not used Label 15 Formats and codes of signalling network management messages 15.1 General The signalling network management messages The signalling information field consist of Label The standard label structure shall apply Heading code (H0) The applicable signalling network management messages are shown in Table 1/Q Changeover message shall apply Changeback message shall apply Emergency changeover message shall apply. A 51 / 62
52 15.7 Transfer-prohibited message Signalling network functions (Q.704) shall apply Transfer-allowed message shall apply Transfer-restricted message Signalling-route-set-test message shall apply Management inhibit message shall apply Traffic restart allowed message Note: Signalling point restart procedure shall not apply Signalling-data-link-connection-order message Note: Automatic allocation of signalling data link shall not apply Signalling-data-link-connection-acknowledgement message Note: Automatic allocation of signalling data link shall not apply Transfer controlled message Note: Multiple congestion states shall not apply Signalling-route-set-congestion-test message (National option) User part unavailable message A 52 / 62
53 Signalling network functions (Q.704) 16 State transition diagrams Shall apply with regard to the relevant level 3 functions Timers and timer values T s "Delay to avoid message mis-sequencing on changeover" T s "Waiting for changeover acknowledgement" T s "Time controlled diversion-delay to avoid mis-sequencing on changeback" T s "Waiting for changeback acknowledgement (first attempt)" T s "Waiting for changeback acknowledgement (second attempt)" T s "Delay to avoid message mis-sequencing on controlled rerouting" T7 Not used. T s "Transfer prohibited inhibition timer (transient solution)" T9 Not used. T s "Waiting to repeat signalling route set test message" T11 Not used. T s "Waiting for uninhibit acknowledgement" T s "Waiting for forced uninhibit" T s "Waiting for inhibition acknowledgement" T15 T16 Not used. Not used. T s "Delay to avoid oscillation of initial alignment..." T18 T19 T20 T21 Not used. Not used. Not used. Not used. T min. "Local inhibit test timer" T min "Remote inhibit timer" T24 Not used. Table 1/Q.704 A 53 / 62
54 Signalling network functions (Q.704) Heading code allocation of signalling network management messages Messag e Group H1 H CHM 0001 COO COA CBD CBA ECM 0010 ECO ECA FCM 0011 TFC TFM 0100 TFP TFA RSM 0101 RST MIM 0110 LIN LUN LIA LUA LID LFU LLT LRT Abbreviations: CHM COO COA CBD CBA ECM ECO ECA Changeover and changeback messages Changeover order signal Changeover acknowledgement signal Changeback declaration signal Changeback acknowledgement signal Emergency changeover messages Emergency changeover order signal Emergency changeover acknowledgement signal FCM TFC Signalling traffic flow control message Transfer controlled signal TFM TFP TFA RSM RST MIM LIN LUN LIA LUA LID LFU LLT LRT Transfer prohibited transfer allowed transfer restricted messages Transfer-prohibited signal Transfer-allowed signal Signalling-route-set-test message Signalling-route-set test signal Management inhibit messages Link inhibit signal Link uninhibit signal Link inhibit acknowledgement signal Link uninhibit acknowledgement signal Link inhibit denied signal Link forced uninhibit signal Link local inhibit test signal Link remote inhibit test signal A 54 / 62
55 Signalling network structure (Q.705) CHAPTER 6 Signalling network structure (Q.705) A 55 / 62
56 Signalling network structure (Q.705) Signalling network structure (Q.705) The Recommendation shall apply completely A 56 / 62
57 MTP signalling performance (Q.706) CHAPTER 7 Message Transfer Part Signalling Performance (Q.706) A 57 / 62
58 MTP signalling performance (Q.706) Message Transfer Part Signalling Performance (Q.706) The Recommendation shall apply completely ] A 58 / 62
59 Testing and maintenance requirements (Q.707) CHAPTER 8 Testing and maintenance requirements (Q.707) A 59 / 62
60 Testing and maintenance requirements (Q.707) Testing and maintenance requirements (Q.707) 1 General 2 Testing 2.1 Signalling data link test 2.2 Signalling link test 3 Fault location 4 Signalling network monitoring Note: All the mandatory measurements described in Recommendations Q.791 are applicable. 5 Formats and codes of signalling network testing and maintenance messages 5.1 General 5.2 Label 5.3 Heading code H0 A 60 / 62
61 Testing and maintenance requirements (Q.707) 5.4 Signalling link test messages 5.5 Time-out values and tolerances T s "Supervision timer for signalling link test acknowledgement message" 6 State transition diagrams Shall apply with regard to the relevant functions. 1 This value must be equal or greater than T6 of Q.703. A 61 / 62
62 References Document history Document history Status Date Details of change "A" 62/61
) IGNALLING LINK. SERIES Q: SWITCHING AND SIGNALLING Specifications of Signalling System No. 7 Message transfer part. ITU-T Recommendation Q.
INTERNATIONAL TELECOMMUNICATION UNION )454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (07/96) SERIES Q: SWITCHING AND SIGNALLING Specifications of Signalling System. 7 Message transfer part 3IGNALLING
More information)454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU
INTERNATIONAL TELECOMMUNICATION UNION )454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU 30%#)&)#!4)/.3 /& 3)'.!,,).' 3934%-.O 4%34).'!.$ -!).4%.!.#% )454 Recommendation 1 (Extract from the "LUE "OOK)
More information)454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU
INTERNATIONAL TELECOMMUNICATION UNION )454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU 30%#)&)#!4)/.3 /& 3)'.!,,).' 3934%- 2 ).4%22%')34%2 3)'.!,,).' 3)'.!,,).' #/$% )454 Recommendation 1 (Extract
More informationINTERNATIONAL TELECOMMUNICATION UNION DATA COMMUNICATION NETWORK: INTERFACES
INTERNATIONAL TELECOMMUNICATION UNION CCITT X.21 THE INTERNATIONAL (09/92) TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE DATA COMMUNICATION NETWORK: INTERFACES INTERFACE BETWEEN DATA TERMINAL EQUIPMENT
More information- 1 - Rep. ITU-R M.2009 REPORT ITU-R M.2009 DIRECT-DIAL TELEPHONE SYSTEMS FOR THE MARITIME MOBILE SERVICE
- 1 - REPORT ITU-R M.2009 DIRECT-DIAL TELEPHONE SYSTEMS FOR THE MARITIME MOBILE SERVICE (1995) General Although the DSC system may be used to establish fully automatic systems in the directions ship-to-shore,
More informationSuperseded by a more recent version INTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION ITU-T V.24 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (10/96) SERIES V: DATA COMMUNICATION OVER THE TELEPHONE NETWORK Interfaces and voiceband modems List of
More informationBASIC USER-NETWORK INTERFACE LAYER 1 SPECIFICATION
INTERNATIONAL TELECOMMUNICATION UNION CCITT I.430 THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE (11/1988) SERIES I: INTEGRATED SERVICES DIGITAL NETWORK (ISDN) OVERALL NETWORK ASPECTS
More informationINTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION ITU-T G.775 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (10/98) SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS Digital transmission systems
More information)454 & 4%,%'2!- 2%42!.3-)33)/. 3934%- /0%2!4)/.3!.$ 15!,)49 /& 3%26)#% 4%,%'2!0( 3%26)#%3. )454 Recommendation & INTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION )454 & TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU /0%2!4)/.3!.$ 15!,)49 /& 3%26)#% 4%,%'2!0( 3%26)#%3 4%,%'2!- 2%42!.3-)33)/. 3934%- )454 Recommendation & (Extract
More informationRecommendation T/CS (Vienna 1982, revised in Montpelier 1984) SYSTEM L1 MULTIFREQUENCY PUSH-BUTTON INTERREGISTER SIGNALING
o -r/es 49-04 E B Page 1 Recommendation T/CS 49-04 (Vienna 1982, revised in Montpelier 1984) SYSTEM L1 MULTFREQUENCY PUSH-BUTTON NTERREGSTER SGNALNG Recommendation proposed by Working Group T/WG 11 Switching
More informationINTERNATIONAL TELECOMMUNICATION UNION DATA COMMUNICATION OVER THE TELEPHONE NETWORK
INTERNATIONAL TELECOMMUNICATION UNION ITU-T V.24 TELECOMMUNICATION (03/93) STANDARDIZATION SECTOR OF ITU DATA COMMUNICATION OVER THE TELEPHONE NETWORK LIST OF DEFINITIONS FOR INTERCHANGE CIRCUITS BETWEEN
More informationEUROPEAN pr ETS TELECOMMUNICATION February 1996 STANDARD
FINAL DRAFT EUROPEAN pr ETS 300 118 TELECOMMUNICATION February 1996 STANDARD Second Edition Source: ETSI TC-TE Reference: RE/TE-05049 ICS: 33.020 Key words: PSTN, modems Public Switched Telephone Network
More information)454 6 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU
INTERNATIAL TELECOMMUNICATI UNI )454 6 TELECOMMUNICATI STANDARDIZATI SECTOR OF ITU $!4! #/--5.)#!4)/. /6% 4(% 4%,%0(/.%.%47/+,//0 4%34 $%6)#%3 &/ -/$%-3 )454 Recommendation 6 (Extract from the "LUE "OOK)
More informationEUROPEAN ETS TELECOMMUNICATION October 1998 STANDARD
EUROPEAN ETS 300 012-1 TELECOMMUNICATION October 1998 STANDARD Second Edition Source: TM Reference: RE/TM-03038-1 ICS: 33.020 Key words: Basic, ISDN, layer 1, transmission, UNI, rate Integrated Services
More informationINTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION )454 8 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU 05",)# $!4!.%47/2+3 ).4%2&!#%3,)34 /& $%&).)4)/.3 &/2 ).4%2#(!.'% #)2#5)43 "%47%%. $!4! 4%2-).!, %15)0-%.4 $4%!.$
More informationGENERAL CONSIDERATIONS ON TRANSMULTIPLEXING EQUIPMENTS. (Geneva, 1980; further amended)
5i 7.9 Other terminal equipments Recommendation G.791 GENERAL CONSIDERATIONS ON TRANSMULTIPLEXING EQUIPMENTS (Geneva, 1980; further amended) The CCITT, considering the advantages offered in some cases
More informationINTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION CCITT G.703 THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE (11/1988) SERIE G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS General
More informationRECOMMENDATION ITU-R M.541-8*
Rec. ITU-R M.541-8 1 RECOMMENDATION ITU-R M.541-8* OPERATIONAL PROCEDURES FOR THE USE OF DIGITAL SELECTIVE-CALLING EQUIPMENT IN THE MARITIME MOBILE SERVICE (Question ITU-R 9/8) (1978-1982-1986-1990-1992-1994-1995-1996-1997)
More information)454 1 '%.%2!,!30%#43 /& 05",)#,!.$ -/"),%.%47/2+3 05",)#,!.$ -/"),%.%47/2+3. )454 Recommendation 1 INTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION )454 1 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU 05",)#,!.$ -/"),%.%47/2+3 '%.%2!,!30%#43 /& 05",)#,!.$ -/"),%.%47/2+3 )454 Recommendation 1 (Extract from the
More informationPHYSICAL/ELECTRICAL CHARACTERISTICS OF HIERARCHICAL DIGITAL INTERFACES. (Geneva, 1972; further amended)
5i Recommendation G.703 PHYSICAL/ELECTRICAL CHARACTERISTICS OF HIERARCHICAL DIGITAL INTERFACES (Geneva, 1972; further amended) The CCITT, considering that interface specifications are necessary to enable
More informationETSI TS V1.1.1 ( ) Technical Specification
TS 100 392-3-8 V1.1.1 (2008-04) Technical Specification Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 3: Interworking at the Inter-System Interface (ISI); Sub-part 8: Generic Speech Format
More informationETSI TS V1.1.1 ( )
TS 100 392-3-7 V1.1.1 (2003-12) Technical Specification Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 3: Interworking at the Inter-System Interface (ISI); Sub-part 7: Speech Format Implementation
More informationCONTROLLER SPECIFICATION.
colin.subryan@tfl.gov.uk Colin Subryan Principal Engineer, Transport for London, Traffic Directorate Telephone 0203 054 2530 Email colin.subryan@tfl.gov.uk Management of a team with responsibility for
More informationInstruction manual. art Installation manual
Instruction manual art. 01521 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 4 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL FEATURES AND
More informationThorsten Reibel, Training & Qualification Global Application and Solution Team
JUNE 2017 Gateways DG/S x.64.1.1 Part 2 BU EPBP GPG Building Automation Thorsten Reibel, Training & Qualification Global Application and Solution Team Agenda New Generation DALI-Gateways DG/S x.64.1.1
More informationIMO RESOLUTION A.1001(25) Adopted on 29 November 2007 (Agenda item 9)
INTERNATIONAL MARITIME ORGANIZATION E IMO ASSEMBLY 25th session Agenda item 9 A 25/Res.1001 3 January 2008 Original: ENGLISH RESOLUTION A.1001(25) Adopted on 29 November 2007 (Agenda item 9) CRITERIA FOR
More information,787, 35,0$5<5$7(86(51(7:25.,17(5)$&(±/$<(563(&,),&$7,21 ,17(*5$7('6(59,&(6',*,7$/ 1(7:25.,6'1,6'186(51(7:25.,17(5)$&(6 ,7875HFRPPHQGDWLRQ,
INTERNATIONAL TELECOMMUNICATION UNION,787, TELECOMMUNICATION (03/93) STANDARDIZATION SECTOR OF ITU,17(*5$7('6(59,&(6',*,7$/ 1(7:25.,6'1,6'186(51(7:25.,17(5)$&(6 35,0$5
More informationIncreasing Broadcast Reliability for Vehicular Ad Hoc Networks. Nathan Balon and Jinhua Guo University of Michigan - Dearborn
Increasing Broadcast Reliability for Vehicular Ad Hoc Networks Nathan Balon and Jinhua Guo University of Michigan - Dearborn I n t r o d u c t i o n General Information on VANETs Background on 802.11 Background
More informationRECOMMENDATION ITU-R M * Definition of availability for radiocommunication circuits in the mobile-satellite service
Rec. ITU-R M.828-2 1 RECOMMENDATION ITU-R M.828-2 * Definition of availability for radiocommunication circuits in the mobile-satellite service (Question ITU-R 85/8) (1992-1994-2006) Scope This Recommendation
More informationAPPENDIX A PARAMETER DESCRIPTIONS
APPENDIX A PARAMETER DESCRIPTIONS CONTENTS Page INTRODUCTION A.5 CHANNEL PARAMETERS #101 -#102 Channel Frequencies A.5 #103 Microcomputer Clock Offset A.6 #104 Transmitter Power A.6 #105 Squelch A.6 #106
More informationDESCRIPTION OF INTENDED SINGLE SOURCE PURCHASE (PUR 7776)
DESCRIPTION OF INTENDED SINGLE SOURCE PURCHASE (PUR 7776) AGENCY Department of Management Services TITLE Mutual Aid Communication Microwave Short description of the commodity or service desired: Microwave
More information)454 ) "!3)# 53%2.%47/2+ ).4%2&!#%,!9%2 30%#)&)#!4)/. ).4%'2!4%$ 3%26)#%3 $)')4!,.%47/2+ )3$. )3$. 53%2.%47/2+ ).4%2&!#%3. )454 Recommendation )
INTERNATIONAL TELECOMMUNICATION UNION )454 ) TELECOMMUNICATION (11/95) STANDARDIZATION SECTOR OF ITU ).4%'2!4%$ 3%26)#%3 $)')4!,.%47/2+ )3$. )3$. 53%2.%47/2+ ).4%2&!#%3 "!3)# 53%2.%47/2+ ).4%2&!#%,!9%2
More informationEUROPEAN pr ETS TELECOMMUNICATION November 1996 STANDARD
FINAL DRAFT EUROPEAN pr ETS 300 723 TELECOMMUNICATION November 1996 STANDARD Source: ETSI TC-SMG Reference: DE/SMG-020651 ICS: 33.060.50 Key words: EFR, digital cellular telecommunications system, Global
More informationSummary. Rec. ITU-R M RECOMMENDATION ITU-R M *
Rec. ITU-R M.492-6 1 RECOMMENDATION ITU-R M.492-6 * Rec. ITU-R M.492-6 OPERATIONAL PROCEDURES FOR THE USE OF DIRECT-PRINTING TELEGRAPH EQUIPMENT IN THE MARITIME MOBILE SERVICE (Question ITU-R 5/8) (1974-1978-1982-1986-1990-1992-1995)
More informationUnderstanding PMC Interactions and Supported Features
CHAPTER3 Understanding PMC Interactions and This chapter provides information about the scenarios where you might use the PMC, information about the server and PMC interactions, PMC supported features,
More information1. Use of the application program
s GAMMA instabus 12 A1S2 Blind, 2 inputs 207301 1. Use of the application program 2. Product description 2.1. Description of the blind actuator UP 520/31 2.2. Delivered with the blind actuator UP 520/31
More information) ,4)0,%8 $4%$#% ).4%2&!#% &/2 53%2 #,!33%3 05",)# $!4!.%47/2+3 ).4%2&!#%3. )454 Recommendation 8 INTERNATIONAL TELECOMMUNICATION UNION
INTERNATIONAL TELECOMMUNICATION UNION )454 8 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU 05",)# $!4!.%47/2+3 ).4%2&!#%3-5,4)0,%8 $4%$#% ).4%2&!#% &/2 53%2 #,!33%3 )454 Recommendation 8 (Extract from
More information3GPP TS V5.0.0 ( )
TS 26.171 V5.0.0 (2001-03) Technical Specification 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Speech Codec speech processing functions; AMR Wideband
More information) #(2/./53 $!4! 42!.3-)33)/.!4! $!4! 3)'.!,,).' 2!4% ()'(%2 4(!. KBITS 53).' K(Z '2/50 "!.$ #)2#5)43
INTERNATIONAL TELECOMMUNICATION UNION )454 6 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU $!4! #/--5.)#!4)/. /6%2 4(% 4%,%(/.%.%47/2+ 39.#(2/./53 $!4! 42!.3-)33)/.!4! $!4! 3)'.!,,).' 2!4% ()'(%2 4(!.
More informationAbsolute Block. Uncontrolled When Printed Document to be part superseded by GKRT0055 Iss 1 and GKRT0077 Iss 1 (published on 07/09/2013)
Signatures removed from electronic version Submitted by... Richard Genner Nominated Responsible Manager Approved by... Philip Wiltshire Chairman, Train Control & Communications Subject Committee Approved
More informationEUROPEAN ETS TELECOMMUNICATION July 1997 STANDARD
EUROPEAN ETS 300 719-2 TELECOMMUNICATION July 1997 STANDARD Source: ETSI TC-RES Reference: DE/RES-04005-2 ICS: 33.020 Key words: Paging, private, radio Radio Equipment and Systems (RES); Private wide area
More informationRecommendation proposed by Working Group T/WG 10 Data Communications (CD)
o T/CD 02-01 E B Page 1 Recommendation T/CD 02-01 E (Ostende 1979, revised at Cannes 1983) Concerning the specification of engineering requirements for a synchronous digital multiplexer operating at 64
More informationETSI ETR TECHNICAL July 1998 REPORT
ETSI ETR 300-5 TECHNICAL July 1998 REPORT Source: TETRA Reference: DTR/TETRA-01011-5 ICS: 33.020 Key words: TETRA, dialling, addressing Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Designers'
More informationConfiguring OSPF. Information About OSPF CHAPTER
CHAPTER 22 This chapter describes how to configure the ASASM to route data, perform authentication, and redistribute routing information using the Open Shortest Path First (OSPF) routing protocol. The
More informationRECOMMENDATION ITU-R S.1594 *
Rec. ITU-R S.1594 1 RECOMMENDATION ITU-R S.1594 * Maximum emission levels and associated requirements of high density fixed-satellite service earth stations transmitting towards geostationary fixed-satellite
More informationSuperseded by a more recent version INTERNATIONAL TELECOMMUNICATION UNION GENERAL ASPECTS OF DIGITAL TRANSMISSION SYSTEMS
INTERNATIONAL TELECOMMUNICATION UNION ITU-T G.74 TELECOMMUNICATION (7/95) STANDARDIZATION SECTOR OF ITU GENERAL ASPECTS OF DIGITAL TRANSMISSION SYSTEMS SYNCHRONOUS FRAME STRUCTURES USED AT 544, 632, 248,
More informationRecommendation T/CS (Vienna 1982) ANALOGUE SUBSCRIBER LINE TESTS AND MEASUREMENTS
o T/es 54-07 E B Page 1 Recommendation T/CS 54-07 (Vienna 1982) ANALOGUE SUBSCRIBER LINE TESTS AND MEASUREMENTS Recommendation proposed by Working Group T/No. 11 Switching and Signaling (CS) Text of the
More informationETSI TS V5.1.0 ( )
TS 101 644 V5.1.0 (2001-02) Technical Specification Digital cellular telecommunications system (Phase 2+); Interworking between Phase 1 infrastructure and Phase 2 Mobile Stations (MS); (GSM 09.90 version
More informationTranscoding free voice transmission in GSM and UMTS networks
Transcoding free voice transmission in GSM and UMTS networks Sara Stančin, Grega Jakus, Sašo Tomažič University of Ljubljana, Faculty of Electrical Engineering Abstract - Transcoding refers to the conversion
More informationSYNCHRONISING AND VOLTAGE SELECTION
SYNCHRONISING AND VOLTAGE SELECTION This document is for Relevant Electrical Standards document only. Disclaimer NGG and NGET or their agents, servants or contractors do not accept any liability for any
More information3GPP TS V8.0.1 ( )
TS 08.52 V8.0.1 (2002-05) Technical Specification 3rd Generation Partnership Project; Technical Specification Group GSM EDGE Radio Access Network; Base Station Controller - Base Transceiver Station (BSC
More informationBASIC PARAMETERS FOR THE MEASUREMENT OF ERROR PERFORMANCE AT BIT RATES BELOW THE PRIMARY RATE
INTERNATIONAL TELECOMMUNICATION UNION CCITT O.153 THE INTERNATIONAL TELEGRAPH AND TELEPHONE CONSULTATIVE COMMITTEE (11/1988) SERIES O: SPECIFICATIONS FOR MEASURING EQUIPMENT Equipment for the measurement
More informationDraft ES V1.1.2 ( )
Standard Public Switched Telephone Network (PSTN); Protocol over the local loop for display services; Server Display and Script Services (SDSS) [European adaptation of Bellcore SR-INS-002461 and TR-NWT-001273]
More informationTECHNICAL TBR 2 BASIS for January 1997 REGULATION
TECHNICAL TBR 2 BASIS for January 1997 REGULATION Source: ETSI TC-TE Reference: DTBR/TE-005002 ICS: 33.020, 33.040.40 Key words: PDN, testing, type approval, X.25 Attachment requirements for Data Terminal
More information28 April r2 SAS-2 BROADCAST processing clarifications
To: T10 Technical Committee From: Ed D Avignon, Vitesse Semiconductor (davignon@vitesse.com) and Rob Elliott, HP (elliott@hp.com) Date: 28 April 2006 Subject: 06-177r2 SAS-2 BROADCAST processing clarifications
More informationETSI EN V1.3.1 ( )
EN 301 489-2 V1.3.1 (2002-08) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard
More informationValidation Plan: Mitchell Hammock Road. Adaptive Traffic Signal Control System. Prepared by: City of Oviedo. Draft 1: June 2015
Plan: Mitchell Hammock Road Adaptive Traffic Signal Control System Red Bug Lake Road from Slavia Road to SR 426 Mitchell Hammock Road from SR 426 to Lockwood Boulevard Lockwood Boulevard from Mitchell
More informationETSI ETR 366 TECHNICAL November 1997 REPORT
ETSI ETR 366 TECHNICAL November 1997 REPORT Third Edition Source: ETSI SMG Reference: RTR/SMG-030326QR1 ICS: 33.020 Key words: Digital cellular telecommunications system, Global System for Mobile communications
More informationTR V4.3.0 ( )
Technical Report Digital cellular telecommunications system (Phase 2); Multiband operation of GSM/DCS 1800 by a single operator (GSM 03.26 version 4.3.0) GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS R European
More informationTS V1.1.1 ( )
Technical Specification Corporate telecommunication Networks (CN); CEPT signalling systems (L1 and L2) for analogue inter-pabx lines European Telecommunications Standards Institute 2 Reference DTS/CN-00006
More informationDEDICATED SHORT-RANGE COMMUNICATION SYSTEM
DEDICATED SHORT-RANGE COMMUNICATION SYSTEM TEST ITEMS AND CONDITIONS FOR MOBILE STATION COMPATIBILITY CONFIRMATION ARIB TECHNICAL REPORT VERSION 1.0 ARIB TR-T16 Version 1.0 September 9th 2001 Association
More informationEESS 501 REVISION HISTORY
Page i EESS 5 REVISION HISTORY Issue/Revision Revision Date Pages revised since the last version / 4 November 994 Original Issue 2/ 3 August 996 All 3/ March 24 All Page ii TABLE OF CONTENTS INTRODUCTION
More information3GPP TS V8.0.0 ( )
TS 46.031 V8.0.0 (2008-12) Technical Specification 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Full rate speech; Discontinuous Transmission (DTX) for
More information)454 ' ).4%27/2+).' "%47%%..%47/2+3 "!3%$ /. $)&&%2%.4 $)')4!, ()%2!2#()%3!.$ 30%%#( %.#/$).',!73 $)')4!,.%47/2+3. )454 Recommendation '
INTERNATIONAL TELECOMMUNICATION UNION )454 ' TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU $)')4!,.%47/2+3 ).4%27/2+).' "%47%%..%47/2+3 "!3%$ /. $)&&%2%.4 $)')4!, ()%2!2#()%3!.$ 30%%#( %.#/$).',!73 )454
More informationDraft ETSI EN V1.3.1 ( )
Draft EN 300 659-2 V1.3.1 (2000-09) European Standard (Telecommunications series) Access and Terminals (AT); Analogue access to the Public Switched Telephone Network (PSTN); Subscriber line protocol over
More informationEUROPEAN pr ETS TELECOMMUNICATION March 1996 STANDARD
DRAFT EUROPEAN pr ETS 300 729 TELECOMMUNICATION March 1996 STANDARD Source: ETSI TC-SMG Reference: DE/SMG-020681 ICS: 33.060.50 Key words: EFR, DTX, digital cellular telecommunications system, Global System
More informationEUROPEAN ETS TELECOMMUNICATION January 1998 STANDARD
EUROPEAN ETS 300 778-2 TELECOMMUNICATION January 1998 STANDARD Source: ATA Reference: DE/ATA-005062-2 ICS: 33.020 Key words: PSTN, CLIP, supplementary services Public Switched Telephone Network (PSTN);
More information)454 ' TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU
INTERNATIONAL TELECOMMUNICATION UNION )454 ' TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU '%.%2!,!30%#43 /& $)')4!, 42!.3-)33)/. 3934%-3 4%2-).!, %15)0-%.43 4()2$ /2$%2 $)')4!, -5,4)0,%8 %15)0-%.4 /0%2!4).'!4
More informationSYSTEM SENSOR WIRELESS REMOTE INDICATOR PRODUCT SPECIFICATION
Model name: M200I-RF Introduction: The 200 Series Commercial RF System is designed for use with compatible intelligent fire systems using the System Sensor 200/500 Series CLIP, Enhanced and Advanced communication
More informationApplication Note. How to configure networked ecna automations to use a single LVM-250 Voltage Monitor using Virtual I/O.
Application Note How to configure networked ecna automations to use a single LVM-250 Voltage Monitor using Virtual I/O Introduction The LVM-250 Voltage Monitor is used in conjunction with the ecna to monitor
More informationSTATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE. January 15, 2016
STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE January 15, 2016 919.01 Traffic Signal Cabinet and Controller Unit General Requirements 919.02 Approved
More informationV5 - UK PSTN MAPPING REQUIREMENTS
NICC Document ND1703:1998/07 ND1703:1998/07 V5 - UK PSTN MAPPING REQUIREMENTS Protocol Implementation Conformance Statement (PICS) proforma Network Interoperability Consultative Committee Ofcom Riverside
More informationETSI EN V1.1.1 ( )
EN 300 471-2 V1.1.1 (2001-05) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Rules for Access and
More information3GPP TS V8.0.0 ( )
TS 46.081 V8.0.0 (2008-12) Technical Specification 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Discontinuous Transmission (DTX) for Enhanced Full Rate
More information3GPP TS V8.0.0 ( )
Technical Specification 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Half rate speech; Discontinuous Transmission (DTX) for half rate speech traffic channels
More informationITU Recommendations and QoS parameters related to Signalling Network design 4.5
INTERNATIONAL TELECOMMUNICATION UNION Telecommunications Development Bureau (BDT) Network Planning Strategy for Evolving Network Architectures Bangkok, 11-15 November 2002 Riccardo Passerini, ITU-BDT ITU
More informationDraftETSI EN V1.2.1 ( )
Draft EN 300 659-2 V1.2.1 (1999-12) European Standard (Telecommunications series) Public Switched Telephone Network (PSTN); Subscriber line protocol over the local loop for display (and related) services;
More informationINTERNATIONAL TELECOMMUNICATION UNION '%.%2!,!30%#43 /& $)')4!, 42!.3-)33)/. 3934%-3
INTERNATIONAL TELECOMMUNICATION UNION )454 ' TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU '%.%2!,!30%#43 /& $)')4!, 42!.3-)33)/. 3934%-3 4%2-).!, %15)0-%.43 3%#/.$ /2$%2 $)')4!, -5,4)0,%8 %15)0-%.4
More informationWHEREAS, the City of (the City ) is an Illinois municipality in. accordance with the Constitution of the State of Illinois of 1970; and,
SMALL CELL ANTENNA/TOWER RIGHT-OF-WAY SITING ORDINANCE WHEREAS, the City of (the City ) is an Illinois municipality in accordance with the Constitution of the State of Illinois of 1970; and, WHEREAS, the
More informationEN V6.3.1 ( )
European Standard (Telecommunications series) Digital cellular telecommunications system (Phase 2+); General Packet Radio Service (GPRS); Mobile Station (MS) - Base Station System (BSS) interface; Radio
More informationGROUND ROUTING PROTOCOL FOR USE WITH AUTOMATIC LINK ESTABLISHMENT (ALE) CAPABLE HF RADIOS
GROUND ROUTING PROTOCOL FOR USE WITH AUTOMATIC LINK ESTABLISHMENT (ALE) CAPABLE HF RADIOS October 2002 I FOREWORD 1. The Combined Communications-Electronics Board (CCEB) is comprised of the five member
More informationTECHNICAL TBR 25 BASIS for July 1997 REGULATION
TECHNICAL TBR 25 BASIS for July 1997 REGULATION Source: ETSI TC-BTC Reference: DTBR/BTC-02060 ICS: 33.040.40 Key words: Access, digital, interface, leased line, ONP, terminal, testing, type approval Business
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61993-2 First edition 2001-12 Maritime navigation and radiocommunication equipment and systems Automatic identification systems (AIS) Part 2: Class A shipborne equipment of the
More informationENTSO-E Draft Network Code on High Voltage Direct Current Connections and DCconnected
ENTSO-E Draft Network Code on High Voltage Direct Current Connections and DCconnected Power Park Modules 30 April 2014 Notice This document reflects the work done by ENTSO-E in line with ACER s framework
More informationb. When transmitting a message through a transmission medium, the equipment which receives the message should first find out whether it has received
b. When transmitting a message through a transmission medium, the equipment which receives the message should first find out whether it has received the message correctly. If there is an error the receive
More informationEUROPEAN ETS TELECOMMUNICATION April 2000 STANDARD
EUROPEAN ETS 300 729 TELECOMMUNICATION April 2000 STANDARD Second Edition Source: SMG Reference: RE/SMG-020681R1 ICS: 33.020 Key words: Digital cellular telecommunications system, Global System for Mobile
More informationETSI EN V8.0.1 ( )
EN 300 729 V8.0.1 (2000-11) European Standard (Telecommunications series) Digital cellular telecommunications system (Phase 2+); Discontinuous Transmission (DTX) for Enhanced Full Rate (EFR) speech traffic
More information3GPP TS V ( )
TS 32.450 V13.0.0 (2016-01) Technical Specification 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Telecommunication management; Key Performance Indicators
More informationETSI TS V8.0.0 ( ) Technical Specification
Technical Specification Digital cellular telecommunications system (Phase 2+); Enhanced Full Rate (EFR) speech processing functions; General description () GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS R 1 Reference
More informationRochester Institute of Technology Real Time and Embedded Systems: Project 2a
Rochester Institute of Technology Real Time and Embedded Systems: Project 2a Overview: Design and implement a STM32 Discovery board program exhibiting multitasking characteristics in simultaneously controlling
More informationAppendix C T1 Overview
Appendix C T Overview GENERAL T refers to the primary digital telephone carrier system used in North America. T is one line type of the PCM T-carrier hierarchy listed in Table C-. T describes the cabling,
More informationInternational maritime VHF radiotelephone system with automatic facilities based on DSC signalling format
Recommendation ITU-R M.689-3 (03/2012) International maritime VHF radiotelephone system with automatic facilities based on DSC signalling format M Series Mobile, radiodetermination, amateur and related
More informationETSI ES V1.2.1 ( )
ES 201 235-2 V1.2.1 (2002-03) Standard Access and Terminals (AT); Specification of Dual-Tone Multi-Frequency (DTMF) Transmitters and Receivers; Part 2: Transmitters 2 ES 201 235-2 V1.2.1 (2002-03) Reference
More informationATS-I USER MANUAL. Tecnoelettra srl Dal Via Vioni Dimo, S.Rocco di Guastalla (RE)
USER MANUAL ATS-I Tel.+39.0522.832004 P1/17 ATS-I User manual Fax.+39.0522.832012 Tecnoelettra_EN.doc P.1/17 Index General description...3 Electrical specifics...3 Device operative logic...4 Manual mode...4
More informationETSI EN V1.2.1 ( )
EN 301 489-19 V1.2.1 (2002-11) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard
More informationCITY COMMENTS ON THE OMBUDSMAN S RECOMMENDATIONS
CITY COMMENTS ON THE OMBUDSMAN S RECOMMENDATIONS RECOMMENDATION 1 Eligibility and Appeals We recommend that the City of Winnipeg establish revised Handi-Transit eligibility criteria that considers whether
More informationETSI EN V1.2.1 ( )
EN 301 489-23 V1.2.1 (2002-11) Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard
More informationINTERNATIONAL TELECOMMUNICATION UNION. Timing requirements of slave clocks suitable for use as node clocks in synchronization networks
INTERNATIONAL TELECOMMUNICATION UNION ITU-T G.812 TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU (06/2004) SERIES G: TRANSMISSION SYSTEMS AND MEDIA, DIGITAL SYSTEMS AND NETWORKS Digital networks Design
More informationETSI TR V8.0.0 ( )
TR 101 266 V8.0.0 (2000-03) Technical Report Digital cellular telecommunications system (Phase 2+); Multiband operation of GSM/DCS 1 800 by a single operator (GSM 03.26 version 8.0.0 Release 1999) GLOBAL
More informationEmergency Information Broadcasting Distribution System
Safety Earthquake Early Warning Broadcasting Distribution Function Emergency Information Broadcasting Distribution System Systems for broad and general emergency distribution of earthquake early warnings
More information