OPERATING INSTRUCTIONS PMR446 TRANSCEIVER. Iç-F29SR

Transcription

1 PERATING INSTRUCTINS PMR446 TRANSCEIVER Iç-F29SR

2 INTRDUCTIN FREWRD Thank you for purchasing this Icom transceiver. IMPRTANT FIRST, CAREFULLY READ INSTRUCTINS that are provided with the transceiver. SAVE THIS PERATING INSTRUCTINS These operating instructions contain additional important operating instructions for the IC-F29SR pmr446 transceiver. TABLE F CNTENTS FREWRD... i IMPRTANT... i TABLE F CNTENTS... i 1 ACCESSRIES Accessory attachments... 1 D DBattery pack... 1 D DBelt clip... 1 D DJack cover PRGRAMMABLE KEY FUNCTINS... 3 Programmable key functions LED INDICATR... 4 About the LED indicator SETTINGS Setting the Beep function... 5 Setting the beep level... 6 Setting the ringer level... 7 Setting the group code number... 8 D DCTCSS tone setting... 8 D DDTCS code setting... 9 Setting the microphone gain Setting the squelch level Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. i

3 Section 1 ACCESSRIES Accessory attachments DDBattery pack Attach or remove the battery pack, as illustrated to the right. To attach the battery pack: qqplace the tabs on the bottom of the battery pack into the slots at the bottom of the transceiver. (q) wwpush the battery pack until the battery release but- tons make a click sound. (w) To attach Battery release buttons To remove To remove the battery pack: qqpush the battery release buttons in the direction of the arrow as shown to the right. (e) wwthe battery pack is then released, and you can re- move it. (r) w e e q r DDBelt clip NTE: Before attaching or detaching the belt clip, remove the battery pack from the transceiver, if it is attached. To attach the belt clip: Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a click sound. (q) To detach the belt clip: Lift the tab up ( w), and slide the belt clip in the direction of the arrow (e). To attach q To detach w e Tab 1

4 1 ACCESSRIES Accessory attachments (Continued) DDJack cover CAUTIN: The transceiver meets IP67 requirements for dust-tight and waterproof protection, only when the jack cover or the optional HM-168LWP speaker microphone is attached. To attach the jack cover: qqplace the jack cover over the speaker-microphone jack. (q) wwinsert and tighten the screws. ( w) q w w To detach the jack cover: qqunscrew the screws using a Phillips screwdriver. (e) wwdetach the jack cover. (r) e e r 2

5 Section 2 PRGRAMMABLE KEY FUNCTINS Programmable key functions If you use the CS-F29SR cloning software (purchase separately), you can assign the functions described below to [TP],, and. NTE: Refer to the instruction sheet that comes with the transceiver for the default settings of these keys. [TP] SCAN START/STP Push to start and cancel a scan. When a scan is started with the Power N Scan or Automatic scan function, push this key to pause it. The paused scan resumes after a set time period. PRIRITY A CHANNEL, PRIRITY B CHANNEL Push to select the Priority A or Priority B channel. PRIRITY A CHANNEL (REWRITE), PRIRITY B CHANNEL (REWRITE) Push to select the Priority A or Priority B channel. Hold down to set the operating channel as the Priority A or Priority B channel. MEMRY CHANNELS 1, 2, 3, 4 Push to select memory channel 1, 2, 3, or 4. MNI Push to turn the CTCSS (DTCS) mute N or FF. While holding down this key, the transceiver opens any squelch, or releases any mute. LCK Hold down to turn the Key Lock function N or FF. Even when the Lock function is N, [MNI] and [SUR- VEILLANCE] are not locked. SURVEILLANCE Hold down to turn N the Surveillance function. Push to turn FF the function. When this function is N and a signal is received, a beep does not sound and the status indicator does not light, even if you push any key. SIREN Hold down to emit a siren sound. The transceiver keeps emitting the siren sound until the transceiver s power is turned FF. This function is for situations other than an emergency alert, such as a security alarm. SCRAMBLER Hold down to turn N the Voice Scrambler function. Push to turn FF the function. CMPANDER Hold down to turn N the Compander function. Push to turn FF the function. The Compander function reduces noise components from the transmitted audio to provide clear communication. S-RING/C-RING Push to make a Smart-Ring call. Hold down to make a Call-Ring call. ANNUNCE Push to turn the Channel Announce function N or FF. The transceiver announces the position of [Rotary Selector]. NTE: When the Beep function is FF, the operating channel is not announced, regardless of this setting. (p. 5) 3

6 Section 3 LED INDICATR About the LED indicator The LED indicator indicates the status of various parameters of the transceiver as follows: (Reference: R is Red, G is Green, is range) Cloning (reading or writing data) G G G G G G G G Cloning error (if cloning fails) Inh, Blank CH, Unlocked (when you cannot use the channel) R G R G R G R G R G R G R G R G R R R R R R R R TX Low Battery 1 (while transmitting) R R TX Low Battery 2 (while transmitting) R R R R Transmitting R Receiving G Scanning G G Low Battery 1 (You should charge the battery.) G G Low Battery 2 (You must charge the battery.) G G G G When turning N the power R G R G Making a Smart-Ring call Lockout, TX Inh, TT (when transmit is inhibited) R Smart-Ring call successful G Smart-Ring call failed R Siren G R G R G R G R 4

7 Section 4 SETTINGS Setting the Beep function The Beep function can be turned N or FF. When it is FF, the channel announcement is also turned FF. NTE: You should turn N the Beep function when you set the microphone gain, the squelch level or the group code number to check the current level setting with the beep sounding. (pp. 8 11) [VL] to turn FF the transceiver power. w wset [RTARY SELECTR] to any channel other than Channel 16. e ewhile holding down, rotate [VL] to turn N the power to enter the Beep level adjustment mode. r rpush to turn the Beep function N or FF. When a beep sounds after pushing, the Beep function is N. When no beep sounds after pushing, the Beep function is FF. If desired, push to adjust the Beep level. See page 6 for details. t trotate [VL] to turn FF the power to exit the Beep level adjustment mode. [RTARY SELECTR] [VL] 5

8 4 SETTINGS Setting the beep level You can adjust the beep level between 1 and 5, or 1 (linked) and 5 (linked). When a linked option is selected, you can adjust the beep level by rotating [VL]. [VL] to turn FF the transceiver power. w wset [RTARY SELECTR] to any channel other than Channel 16. e ewhile holding down, rotate [VL] to turn N the power and enter the beep level adjustment mode. r rpush to change the beep level as shown to the right. A beep sounds every time you push. Therefore, you can determine the current level setting by the increasing loudness of the beep that sounds. To determine if you have selected a linked level, set [VL] to minimum, then push repeatedly, listening for the loudest beep (level 5). Pushing once after the loudest beep will select 1 (Linked). Repeatedly push to select the desired linked level. t trotate [VL] to turn FF the power to exit the beep level adjustment mode. [RTARY SELECTR] [VL] Pushing (Linked) 4 (Linked) 3 (Linked) 2 (Linked) 1 (Linked) 6

9 4 SETTINGS Setting the ringer level You can adjust the ringer level between 1 and 5, or 1 (linked) and 5 (linked). When a linked option is selected, you can adjust the ringer level by rotating [VL]. [VL] to turn FF the power. w wset [RTARY SELECTR] to Channel 16. e ewhile holding down, rotate [VL] to turn N the power and enter the ringer level adjustment mode. r rpush to increase, or push to decrease the ringer level as shown to the right. A beep sounds after pushing. Therefore, you can determine the current level setting by the increasing loudness of the beep that sounds. To determine if you have selected a linked level, set [VL] to minimum, then push up to 10 times, listening for the loudest beep (level 5). Pushing once after the loudest beep will select 1 (Linked). Repeatedly push or to select the desired linked level. t trotate [VL] to turn FF the power to exit the ringer level adjustment mode. [RTARY SELECTR] [VL] Pushing (Linked) Pushing 4 (Linked) 3 (Linked) 2 (Linked) 1 (Linked) 7

10 4 SETTINGS Setting the group code number DDCTCSS tone setting The transceiver is equipped with 50 CTCSS tones. CTCSS operation enables silent standby, since you will only receive calls from group members using the same CTCSS tone. [VL] to turn FF the power. w wset [RTARY SELECTR] to any channel other than Channel 16. e ewhile holding down [PTT],, and, rotate [VL] to turn N the power. r rrotate [RTARY SELECTR] to select the desired channel (1 to 16) that you want to assign the CTCSS tone to. t thold down until two beeps sound. The transceiver enters the CTCSS tone setting mode. y ypush [PTT] the necessary number of times to enter the ten s digit of the desired CTCSS tone number (grey column) as shown in the list below. u upush. The selected number will be announced. i ipush [PTT] the necessary number of times to enter the one s digit of the desired CTCSS tone number (grey column) as shown in the list below. o opush to complete the setting. The selected number will be announced.!0 Turn FF the power to exit the CTCSS tone setting mode. [PTT] [RTARY SELECTR] [VL] NTE: If you make a mistake, go back to step q and follow all the steps again. If you want to enter 0, do not push [PTT] in step t and u, just push. Then zero will be announced. To turn FF the CTCSS tone, enter 00. [Example]: CTCSS tone No. 28 (162.2 Hz) assigned to channel 4 [VL] to turn FF the power. w wwhile holding down [PTT],, and, rotate [VL] to turn N the power. The transceiver enters CTCSS tone Setting mode. e erotate [RTARY SELECTR] to select channel 4, then hold down until two beeps sound. r rpush [PTT] two times to enter 2 (the ten s digit) of the number 28. t tpush. Two will be announced. y ypush [PTT] eight times to enter 8 (the one s digit) of the number 28. u upush to complete the setting. Eight will be announced. iiturn FF the power to set the CTCSS tone. Available CTCSS tone list No. Freq. No. Freq. No. Freq. No. Freq. No. Freq (Hz) FF 8

11 4 SETTINGS Setting the group code number (Continued) DDDTCS code setting This transceiver is equipped with 84 DTCS codes. DTCS operation enables silent standby, since you will only receive calls from group members using the same DTCS code. [VL] to turn FF the power. w wset [RTARY SELECTR] to any channel other than Channel 16. e ewhile holding down [PTT],, and, rotate [VL] to turn N the power. r rrotate [RTARY SELECTR] to select the desired channel (1 to 16) that you want to assign the DTCS code to. t thold down until two beeps sound. The transceiver enters the DTCS code setting mode. y ypush [PTT] the necessary number of times to enter the ten s digit of the desired DTCS code number (grey column) as shown in the list below. u upush. The selected number will be announced. i ipush [PTT] the necessary number of times to enter the one s digit of the desired DTCS code number (grey column) as shown in the list below. o opush. The selected number will be announced.!0 If you want to use Inverse mode, push [PTT] again. If you want to use Normal mode, skip this step.!1 Push to complete the setting.!2 Turn FF the power to exit the DTCS Code Setting mode. NTE: If you make a mistake, go back to step q and follow all the steps again. If you want to enter 0, do not push [PTT] in step t and u, just push. Then zero will be announced. To turn FF the DTCS code, enter 0. [Example]: DTCS code No. 16 (114) Inverse mode assignment to channel 5 [VL] to turn FF the power. w wwhile holding down [PTT],, and, rotate [VL] to turn N the power. The transceiver enters DTCS Code Setting mode. e erotate [RTARY SELECTR] to select channel 5, then hold down until two beeps sounds. r rpush [PTT] one time to enter 1 (the ten's digit) of the number 16. t tpush. ne will be announced. y ypush [PTT] six times to enter 6 (the one s digit) of the number 16. u upush. Six will be announced. i ipush [PTT] again, to use Inverse mode. o opush to complete the setting.!0turn FF the power to set the DTCS code. 9 Available DTCS code list No. Code No. Code No. Code No. Code No. Code [PTT] [RTARY SELECTR] [VL] FF

12 4 SETTINGS Setting the microphone gain Higher levels make the microphone more sensitive to the user s voice. [VL] to turn FF the power. w wset [RTARY SELECTR] to Channel 16. e ewhile holding down, rotate [VL] to turn N the power and enter the microphone gain adjustment mode. r rpush or to increase, or push to decrease the microphone gain. The adjustable range is 1 (minimum) to 4 (maximum). A beep sounds after pushing or. An error beep sounds if you try to exceed the adjustable range. NTE: The Beep function should be turned N. (p. 5) t trotate [VL] to turn FF the power to exit the microphone gain adjustment mode. [RTARY SELECTR] [VL] 10

13 4 SETTINGS Setting the squelch level The squelch circuit mutes the received audio signal, depending on the signal strength. [VL] to turn the transceiver power FF. w wset [RTARY SELECTR] to any channel other than Channel 16. e ewhile holding down, rotate [VL] to turn N the power and enter the squelch level adjustment mode. r rpush to increase the squelch level (tight squelch), or push to decrease the squelch level (loose squelch). The adjustable range is 0 (open squelch) and 1 (loose squelch) to 9 (tight squelch). A beep sounds after pushing or. An error beep sounds if you try to exceed the adjustable range. NTE: The Beep function should be turned N. (p. 5) t trotate [VL] to turn FF the power to exit the squelch level adjustment mode. [RTARY SELECTR] [VL] 11

14 A EU 2014 Icom Inc Kamiminami, Hirano-ku, saka , Japan