wenlok.com.mx Switched-mode and uninterruptible power supplies, and electronic fuses Let s connect. Power supply Catalogue 2015/2016

Size: px
Start display at page:

Download "wenlok.com.mx Switched-mode and uninterruptible power supplies, and electronic fuses Let s connect. Power supply Catalogue 2015/2016"

Transcription

1 Switched-mode and uninterruptible power supplies, and electronic fuses Catalogue 2015/2016 Let s connect. Power supply

2 Switch-Mode and Uninterruptible Power Supplies, Electronic Fuses Catalogue 4.3 Switch-Mode and Uninterruptible Power Supplies, Electronic Fuses Uninterruptible power supplies (UPS) Fuse protection for 24 V DC circuits Unregulated power supplies Electrical cabinet socket outlet Contents B C D E ppendix Glossary/Technical appendix Index Index Type / Index Order No. ddresses worldwide W X I

3 Product overview wenlok.com.mx Power supplies Overview connectpower 1ph PROeco connectpower 3ph PROeco connectpower PROeco diode modules Single-phase switched-mode power supply modules Slim design Large temperature range from 25 C to 70 C Three-coloured LED indicators for simple error detection dvanced visual warning at 90 % rated output current International approvals 3-phase switched-mode power supply modules Slim design Large temperature range from 25 C to 70 C Three-coloured LED indicators for simple error detection dvanced visual warning at 90 % rated output current International approvals Diode module for 100 % decoupling of switched-mode power supply modules Optimum doubling of output power Redundancy operation Up to 40 output current can be set International approvals connectpower 1ph PROmax connectpower 3ph PROmax connectpower PRO-M Extension modules Single-phase switched-mode power supply modules Very slim design High degree of efficiency Power category ,000 W Up to five devices can be connected in parallel without a diode module International approvals 3-phase switched-mode power supply modules Very slim design High degree of efficiency Power category ,000 W Up to five devices can be connected in parallel without a diode module International approvals Capacity module for increasing the peak current Diode modules for redundant construction Relay module for monitoring the output voltage connectpower PRO-M pplication solutions connectpower 1ph PRO-H connectpower PRO-H Multi-phase Wide-range input V C V DC larm relay Metal snap-on foot International approvals Single-phase switched-mode power supplies High MTBF values Cl. I Div. 2 + TEX Performance class: 70 to 600 W : 12, 24, 36 and 48 V DC Multi-phase switched-mode power supplies / V C UL approval Performance class: 180 to 600 W II

4 Product overview connectpower PRO-H Redundancy modules connectpower PRO-E connectpower 1ph INSTPOWER 15 or % load sharing Remote On/Off International approvals Cl. I Div. 2 + TEX Wall mounting Flat design Metal housing Performance classes from 25 W to 350 W Universal input and output voltages Single-phase switched-mode power supply modules for the distribution board Compact form Power category 24 and 48 W Universal input and output voltage 5 48 V International approvals connectpower 1ph WVEPOWER connectpower DC/DC converters connectpower UPS control unit Single-phase switched-mode power supply unit Slim design 22.5 mm Power category 12 W International approvals Compact form Metal housing Universal input and output voltage of 5 V to 48 V International approvals Two 24 V models in 10 /20 and 40 Temperature-compensated charging feature, for a long battery life Integrated battery diagnostics including continuous availability test Status relay and additional transistor outputs for remote monitoring Convenient LED displays for easy error analysis connectpower battery module connectpower buffer module compactpower 1ph unregulated power supplies Maintenance-free, lead-acid batteries from 1.3 h to 17 h Integrated temperature sensor for optimal battery charging Integrated fuse for reliable activation Support capacity up to 40 / 30 min or 10 / 90 min Robust metal housing for wall mounting Maintenance-free UPS on a capacitor basis, with a capacity to support 20 / 200 ms Parallel switching to increase the output current or support time Status notification via LED and relay contact Single-phase unregulated power supplies Compact form Standard voltage ~230/400 V to IEC 38 +/ 15 V tap Reliable short-circuit and overload protection III

5 Product overview wenlok.com.mx Power supplies Overview compactpower 3ph unregulated power supplies WVEGURD Electrical cabinet socket outlet 3-phase unregulated power supplies Compact form Nominal voltage to IEC 38 +/- 5 V tap Reliable short-circuit and overload protection Electronic fusing Visual fault indication and potential-free contact Reset input Compact form Simple installation in electrical cabinet TS 35 module can be rail mounted VDE mark of conformity Two-pole with earthing contact IV

6 V

7 Product overview wenlok.com.mx Find the perfect product to meet your requirement Our extensive portfolio of power supplies at a glance Series / family side side dditional functions Recommendation for application Order No. Page PROeco.4 PROmax.14 PRO-H.30 Description Phases C input voltage [V] DC input voltage [V] Rated voltage [V] Rated current [] Power rating [V] Derating at [ C] Power boost [60 s] Status relay Side-by-side connectability Temperature range [ C] Efficiency [%] MTBF time [Mh] Surge category Field cabinets Small and series machine construction Machine construction and plant manufacture Simple process applications Process industry Energy technology Power distribution Marine engineering PRO ECO 72 W 24 V NO PRO ECO 120 W 24 V NO PRO ECO 240 W 24 V NO PRO ECO 480 W 24 V NO 91 % PRO ECO 960 W 24 V NO PRO ECO3 120 W 24 V NO PRO ECO3 240 W 24 V > 55 NO to 88 > 0.5 II PRO ECO3 480 W 24 V NO PRO ECO3 960 W 24 V NO PRO ECO 72 W 12 V NO PRO ECO 120 W 12 V NO PRO ECO 240 W 48 V NO PRO ECO 480 W 48 V NO PRO MX 72 W 24 V CO % PRO MX 120 W 24 V CO PRO MX 180 W 24 V 7, CO PRO MX 240 W 24 V CO PRO MX 480 W 24 V CO PRO MX 960 W 24 V CO to PRO MX3 120 W 24 V x x % CO PRO MX3 240 W 24 V x x CO > 60 > 0.5 III PRO MX3 480 W 24 V x x % CO 91.5 SEMI F PRO MX3 960 W 24 V x x s CO Start-up PRO MX 70 W 5 V PRO MX 72 W 12 V CO 40 C PRO MX 120 W 12 V CO Cl1Div2 PRO MX 240 W 48 V CO PRO MX 480 W 48 V CO 91.5 u Some not yet awarded PRO MX 960 W 48 V CO 92.5 (status July 2014) CP T SNT 70 W 12 V n/a NO CP T SNT 140 W 12 V / n/a NO CP T SNT 90 W 24 V n/a NO 85 % CP T SNT 90 W 24 V 3.8 CL n/a NO CP T SNT 180 W 24 V / n/a NO CP T SNT 360 W 24 V / n/a NO CP T SNT 600 W 24 V / n/a NO > 40 to > 1.8 II CP T SNT 90 W 48 V n/a NO CP T SNT 180 W 48 V / n/a NO CP T SNT 360 W 48 V / n/a NO CP T SNT 600 W 48 V / n/a NO CP T SNT2 180 W 24 V / n/a NO Cl1Div2 CP T SNT2 360 W 24 V / n/a NO CP T SNT2 600 W 24 V / n/a NO NO = NO contact CO = CO contact 40 C = In the range of 40 to 25 C the device starts, but some technical parameter may differ (i. e., ripple-voltage). VI

8 Product overview Series / family dditional functions Order No. Page Description C input voltage [V] DC input voltage [V] Rated voltage [V] DC/DC.68 djustable range [V] Rated current [] Power rating [W] Status relay Parallel connection option Side-by-side connectability Temperature range [ C] (all CE) CP DCDC 250 W 24 V CP DC BUFFER 24 V to CP DC UPS 24 V 20 / U in 0.3 V 20/10 480/ USV.39 B.4 Ergänzungsmodule CP DC UPS 24 V U in 0.3 V CP BTTERY 24 V DC 1,3 h / 11.3 min. 1.3 h CP BTTERY 24 V DC 3,4 h / 11.3 min. 3.4 h CP BTTERY 24 V DC 7,2 h / 26.5 min. 7.2 h 2 to CP BTTERY 24 V DC 12 h / 51 min. 12 h CP BTTERY 24 V DC 17 h / 81 min. 17 h CP T RM 10 (PRO-H redundancy module) to CP T RM 20 (PRO-H redundancy module) CP DM 10 (diode module) U IN to CP DM 20 (diode module) U IN CP M DM 20 (diode module) U IN CP M DM 40 (diode module) U IN to CP M CP (capacity module) U IN 40 /1 ms INSTPOWER.60 CP SNT 24 W 28 V CP SNT 24 W 24 V CP SNT 24 W 15 V 1, to CP SNT 24 W 12 V 1, CP SNT 24 W 5 V CP SNT 25 W 5 V CP SNT 48 W 12 V to CP SNT 48 W 24 V CP SNT 48 W 48 V VII

9 VIII

10 Contents Overview.2 connectpower PROeco.4 connectpower PROmax.14 connectpower PRO-H.30 connectpower PRO-E.44 connectpower INSTPOWER.60 connectpower WVEPOWER.67 connectpower DC/DC converter.68.1

11 Overview wenlok.com.mx The switch-mode power supplies feature a high degree of efficiency, compact dimensions and minimal heat generation. They are an excellent, reliable solution for providing power in all automation applications safely providing 24 V DC voltage. The different product series are optimised for the automation industry: they feature Ex approvals for the processing industry, a flat shape perfect for distribution tasks within buildings, or provide decentralised control voltages. ll-purpose usage: with a wide range of C/DC inputs, single-, double- or three-phase versions, and a wide temperature range. dditional performance increases are possible using simple parallel circuitry. Weidmüller switch-mode power supplies can be depended upon for all applications because of their high efficiency and their resistance to both short circuits and overloads. Weidmüller offers a system of one- and three-phase swtichmode power supplies especially for the PROmax family. These can be expanded with additional modules to create whole system solutions. The appropriate system can be assembled for any type of application: with redundancy circuits containing decoupled outputs, monitoring of the output voltage or triggering of circuit breakers..2

12 Overview C / DC International use wide-range input (both DC as well as C voltages can be used; no switching required) and extensive approvals (UL/CS and GL (EMC 1 bridge)). Parallel connection connectpower Module power can be increased by connecting upto five power supplies in parallel without diode module. connectpower PROeco Narrow connectpower PROmax from 33 mm Space-saving configuration in the switching cabinet through very narrow housing construction and side-by-side connectability. connectpower PRO-H Robust Wide temperature range from 25 C +70 C. connectpower PRO-E Wide choice The right power supply for every application: 1-phase 3, 5, 7.5, 10, 20, 40 and 3-phase 5, 10, 20, 40. connectpower INSTPOWER connectpower WVEPOWER connectpower DC/DC converters.3

13 connectpower PROeco wenlok.com.mx PROeco power supplies with basic functionality and a high level of reliability Single- and three-phase switched-mode power supply units Slim design Large temperature range from 25 C to 70 C The output voltage can be precisely adjusted via the potentiometer on the front Remote monitoring via integrated status relay Three-coloured LED indicators for simple error detection dvanced visual warning at 90 % rated output current International approvals Derating curves Ioutput (% IN) Ioutput (% IN) 480 Watt mbient temperature ( C) 960 Watt mbient temperature ( C) General technical data % \ Ž mbient temp. operating / storage temperature 25 C +70 C / 40 C +85 C Max. perm. air humidity (operation) 5 % 95 % RH Degree of protection IP 20 Class of protection I, with PE connection Pollution degree 2 Insulation voltage input/output 3 kv E/ / 2 kv E/earth / 0.5 kv /earth MTBF > h acc. to IEC 1709 (SN29500) Parallel connection option yes, max. 5 without diode module Housing version metal, corrosion resistant Mounting position, installation notice horizontal on mounting rail TS35, 50 mm spacing top and bottom for free air circulation Short-circuit protection Yes, automatic restart Overload protection Yes, IU characteristic curve Overtemperature protection Yes, automatic restart EMC / shock / vibration Noise emission acc. to EN55022 Class B Noise immunity tests acc. to EN (ESD), EN and EN (Fields), EN (Burst), EN (Surge), EN (conducted), EN (Dips) Limiting of mains voltage harmonic currents cc. to EN Resistance against vibration and shock 1 g acc. to EN50178, shock: 15 g in all directions Electrical safety (applied standards) Electrical equipment of machines cc. to EN60204 Safety transformers for switched-mode power units cc. to EN Machinery with electronic equipment cc. to EN50178 / VDE0160 Safety extra-low voltage SELV acc. to EN , PELV acc. to EN Protective separation / protection against electrical shock VDE / acc. to DIN Protection against dangerous shock currents cc. to VDE

14 connectpower PROeco connectpower PROeco PRO ECO 72W 24V 3 PRO ECO 120W 24V 5 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 6, Char. B, circuit breaker 2...4, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 3 at 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 87 % 4 W / 9.5 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 34 / 125 mm / 578 g CE; TUEV (EN/IEC ); culus; RCM V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 6, Char. B, circuit breaker 3...5, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 5 at 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 87 % 4 W / 15 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 40 / 125 mm / 680 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 3 for L/N/PE 5 (+,--,13,14) 0.5 / / / / / / / for L/N/PE 6 (++,--,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO 72W 24V PRO ECO 120W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..5

15 connectpower PROeco wenlok.com.mx connectpower PROeco PRO ECO 240W 24V 10 PRO ECO 480W 24V 20 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 10, Char. B, circuit breaker 3...4, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 90% 3 W / 24 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 60 / 125 mm / 1026 g CE; TUEV (EN/IEC ); culus; RCM V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max. 5 6 / DI, safety fuse 16, Char. B, circuit breaker 6...8, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 91% 5 W / 43 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 100 / 125 mm / 1557 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 3 for L/N/PE 6 (++,--,13,14) 0.5 / / / / / / / for L/N/PE 7 (++,---,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO 240W 24V PRO ECO 480W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..6

16 connectpower PROeco connectpower PROeco PRO ECO 960W 24V 40 Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 20, Char. B, circuit breaker 16, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 50 C 50 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 93% 6 W / 76 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 160 / 125 mm / 3019 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 3 for L/N/PE 7 (++,---,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO 960W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..7

17 connectpower PROeco wenlok.com.mx connectpower PROeco PRO ECO 72W 12V 6 PRO ECO 120W 12V 10 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 115 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 6, Char. B, circuit breaker 2...4, Char. C, circuit breaker 12 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 12 V DC, I Nenn 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 85 % 4 W / 15 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 34 / 125 mm / 644 g CE; TUEV (EN/IEC ); culus; RCM V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max / DI, safety fuse 6, Char. B, circuit breaker 3...5, Char. C, circuit breaker 12 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 12 V DC, I Nenn 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 87 % 4 W / 20 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 40 / 125 mm / 698 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 3 for L/N/PE 5 (+,--,13,14) 0.5 / / / / / / / for L/N/PE 6 (++,--,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO 72W 12V PRO ECO 120W 12V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..8

18 connectpower PROeco connectpower PROeco PRO ECO 240W 48V 5 PRO ECO 480W 48V 10 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 115 V C 370 V DC / 120 V DC Yes / Max / DI, safety fuse 10, Char. B, circuit breaker 3...4, Char. C, circuit breaker 48 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 100 mv 48 V DC, I Nenn 5 at 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 92 % 5 W / 50 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 60 / 125 mm / 1076 g CE; TUEV (EN/IEC ); culus; RCM V C (wide-range input) V C 100 V C) Hz V DC 120 V DC) 230 V C / 110 V C 370 V DC / 120 V DC Yes / max. 3 6 / DI, safety fuse 16, Char. B, circuit breaker 6...8, Char. C, circuit breaker 48 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 100 mv 48 V DC, I Nenn 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 93% 3 W / 23 W 1 m > 230 V C / > 115 V C > V C / > V C yes, max / 100 / 125 mm / 1570 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 3 for L/N/PE 6 (++,--,13,14) 0.5 / / / / / / / for L/N/PE 7 (++,---,13,14) 0.5 / / / / 4 26 / / / 0.6 Ordering data PRO ECO 240W 48V PRO ECO 480W 48V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..9

19 connectpower PROeco wenlok.com.mx connectpower PROeco PRO ECO3 120W 24V 5 PRO ECO3 240W 24V 10 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3 x 500 V C / 3 x 400 V C 800 V DC / 450 V DC Yes / max / DI, safety fuse 2...3, Char. C, circuit breaker 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3 x 500 V C / 3 x 400 V C 800 V DC / 450 V DC Yes / max / DI, safety fuse 2...3, Char. C, circuit breaker Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 5 at 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 87 % 6 W / 13 W 1 m > 3 x 500 V C / > 3 x 400 V C > 40 3 x 500 V C / > 20 3 x 400 V C yes, max / 40 / 125 mm / 710 g CE; TUEV (EN/IEC ); culus; RCM 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 88% 6 W / 24 W 1 m > 3 x 500 V C / > 3 x 400 V C > 40 3 x 500 V C / > 20 3 x 400 V C yes, max / 60 / 125 mm / 971 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 4 for L1/L2/L3/PE 6 (++,--,13,14) 0.5 / / / / / / / for L1/L2/L3/PE 6 (++,--,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO3 120W 24V PRO ECO3 240W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..10

20 connectpower PROeco connectpower PROeco PRO ECO3 480W 24V 20 PRO ECO3 960W 24V 40 Similar to illustration Similar to illustration Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Ramp-up time / Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Capacitive load Protection against inverse voltage Signalling Indication Floating contact / Contact load Relay on/off General data Degree of efficiency Power loss, idling / Power loss, nominal load Earth leakage current, max. Power factor (approx.) C failure bridging I Nom Parallel connection option Depth x width x height / Weight 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3 x 500 V C / 3 x 400 V C 800 V DC / 450 V DC Yes / max / DI, safety fuse 3...5, Char. C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 55 C 55 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 89% 8 W / 48 W 1 m > 3 x 500 V C / > 3 x 400 V C > 30 3 x 500 V C / > 20 3 x 400 V C yes, max / 100 / 125 mm / 1495 g CE; TUEV (EN/IEC ); culus; RCM 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3 x 500 V C / 3 x 400 V C 800 V DC / 450 V DC Yes / max / DI, safety fuse 10, Char. B, circuit breaker 6...8, Char, C, circuit breaker 24 V DC ± 1 % V (adjustable via potentiometer) 100 ms / < 50 mv 24 V DC, I N 50 C 50 C, 70 C unrestricted Yes LED green (U output > 21.6 V DC), LED yellow (I output > 90% I Rated typ. ), LED red (overload, overtemperature, short-circuit, U output < 20.4 V DC) Yes / max. 30 V DC / 1 voltage > 21.6 V / < 20.4 V, overload 90% 5 W / 95 W 1 m > 3 x 500 V C / > 3 x 400 V C > 25 ms at 3 x 500 V C / > 20 ms at 3 x 400 V C yes, max / 160 / 125 mm / 2899 g CE; TUEV (EN/IEC ); culus; RCM Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque range Nm 4 for L1/L2/L3/PE 7 (++,---,13,14) 0.5 / / / / / / / for L1/L2/L3/PE 7 (++,---,13,14) 0.5 / / / / / / / 0.6 Ordering data PRO ECO3 480W 24V PRO ECO3 960W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system..11

21 connectpower PROeco wenlok.com.mx connectpower PROeco diode module CP DM 10 CP DM 20 E1 E2 V V DC +V V E1 E2 V DC + +V -V +V -V E1 E2 -V E1 E2 -V voltage current voltage current General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Mounting position, installation notice Installation advice Weight 40 V DC max. 2 x max. U in V typical max. or 10 max. for redundancy operation -10 C...55 C -20 C...85 C 95.5% horizontally, on terminal rail TS 35 Clearance: side 2 cm; above/below 10 cm 399 g CE; culus; curus; EC 40 V DC max. 2 x max. U in V typical max. or 20 max. for redundant operations -10 C...55 C -20 C...85 C 97.5% horizontally, on terminal rail TS 35 Clearance: side 2 cm; above/below 10 cm 411 g CE; culus; curus; EC Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm 4 / 0.13 / 6 4 / 0.13 / / 55.5 / / 55.5 / / 0.13 / 6 10 / 0.32 / / 55.5 / / 55.5 / 125 Ordering data CP DM CP DM ccessories.12

22 connectpower PROeco - ccessories Small metal foot Large metal foot Small plastic foot Large plastic foot Type Order No. MT 30 MF Type Order No. MT 45 MF Type Order No. MT 30 BK Type Order No. MT 45 BK Small wall mounting Large wall mounting Type Order No. CP WLLDPTER 30 MM Type Order No. CP WLLDPTER 45 MM Small screwdriver Type Blade type Size/F a b c Order No. SDIK PH SDIS 0.5X3.0X100 B Markers End bracket For DIN rail TS 35 Type Colour Qty. Order No. SM 18/9.5 K MC NE WS white Polyamide with fibre glass, screwable Colour Torque Qty. Order No. WEW 35/1 SW black 1.2 Nm

23 connectpower PROmax wenlok.com.mx connectpower PROmax Derating curve Max. limiting average on state current [] Typ\Temp. 45 C 50 C 55 C 60 C 65 C 70 C 1ph 24 V / 3 3,6 3,3 3,2 3 2,6 2,2 1ph 24 V / 5 6 5,7 5,4 5 4,4 3,8 1ph 24 V / 7,5 9 8,5 8 7,5 6,6 5,6 1ph 24 V / ,3 10,7 10 8,8 7,5 1ph 24 V / ,6 21, ,6 15 1ph 24 V / ,2 42, ,2 30 1ph 5 V / 14 16,8 15, ,3 10,5 1ph 12 V / 6 7,2 6,8 6,4 6 5,3 4,5 1ph 12 V / ,3 10,7 10 8,8 7,5 1ph 48 V / 5 6 5,7 5,4 5 4,4 3,8 1ph 48 V / ,3 10,7 10 8,8 7,5 1ph 48 V / ,6 21, ,6 15 3ph 24 V / 5 6 5,7 5,4 5 4,4 3,8 3ph 24 V / ,3 10,7 10 8,8 7,5 3ph 24 V / ,6 21, ,6 15 3ph 24 V / ,2 42, ,2 30 General technical data Current limiting > 120 % I N Insulation voltage input earth 3.5 kv Insulation voltage output earth 0.5 kv Insulation voltage input/output 4 kv Earth leakage current 3.5 m Series switching capability Yes mbient temp. operating / storage temperature / Start up -25 C C / -40 C C / -40 C Humidity at operating temperature %, no condensation Class of protection / Pollution degree I / 2 MTBF >500,000h (25 C, IEC 61709) Housing version Metal, corrosion resistant Status indication LED red/green and relay ( 21.6 V DC LED green, relay on/ 20.6 LED red, relay off) Mounting position, installation notice Horizontal on TS35 mounting rail, with 50 mm of clearance at top and bottom for air circulation. Can be mounted side by side with no space in between. EMC / shock / vibration Noise immunity tests acc. to Resistance against vibration and shock Electrical safety (applied standards) Electrical equipment of machines Safety transformers for switched-mode power units Machinery with electronic equipment Safety extra-low voltage Protective separation / protection against electrical shock Protection against dangerous shock currents EN55024; EN55022; IEC ,-3; IEC ,-3,-4,-5,-6,-8, g / 30 g in all directions cc. to EN60204 cc. to EN cc. to EN50178 / VDE0160 SELV acc. to EN60950, PELV acc. to EN60204, IEC61204 VDE / acc. to DIN cc. to VDE

24 connectpower PROmax connectpower PROmax PRO MX 72W 24V 3 PRO MX 120W 24V 5 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max. 15 6, Char. B, circuit breaker, 3-5 Char. C, circuit breaker V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max. 15 6, Char. B, circuit breaker, 6, char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 3.6 (1 min), 4.5 (4s) 9 (2ms) 89% > 230 V C min. 20 ms V DC yes, max / 32 / 130 mm 650 g CE; culus; culusex; curus; EC; TUEV 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 6 (1 min), 7.5 (4s) 15 (2ms) 89% > 230 V C min. 20 ms V DC yes, max / 40 / 130 mm 859 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 3.5 Ordering data PRO MX 72W 24V PRO MX 120W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.15

25 connectpower PROmax wenlok.com.mx connectpower PROmax PRO MX 180W 24V 7,5 PRO MX 240W 24V 10 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max , char. B circuit breaker, 6 8, char. C circuit breaker V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max , char. B circuit breaker, 6 8, char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 9 (1 min), (4s) 22,5 (2ms) 91.5% > 230 V C min. 20 ms V DC yes, max / 50 / 130 mm 950 g CE; culus; culusex; curus; EC; TUEV 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 12 (1 min), 15 (4s) 30 (2ms) 91.5% > 230 V C min. 20 ms V DC yes, max / 60 / 130 mm 1050 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 Ordering data PRO MX 180W 24V 7, PRO MX 240W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.16

26 connectpower PROmax connectpower PROmax PRO MX 480W 24V 20 PRO MX 960W 24V 40 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max , Char. B circuit breaker, 10, char. C circuit breaker V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max , char. B circuit breaker, 16, Char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 24 (1 min), 30 (4s), V C 60 (2ms) 92 % > 230 V C min. 20 ms V DC yes, max / 90 / 130 mm 2000 g CE; culus; culusex; curus; EC; TUEV 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 48 (1 min), 60 (4s), V C 120 (2ms) 93% > 230 V C min. 20 ms V DC yes, max / 140 / 130 mm 3900 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / / / x 4.0, PZ x 5.5 Ordering data PRO MX 480W 24V PRO MX 960W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.17

27 connectpower PROmax wenlok.com.mx connectpower PROmax PRO MX 70W 5V 14 PRO MX 72W 12V 6 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max. 15 6, Char. B, circuit breaker, 3-5 Char. C, circuit breaker V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max. 15 6, Char. B, circuit breaker, 3-5 Char. C, circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 5 V DC V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 16.8 (1 min), 21 (4s) 42 (2ms) 86% > 230 V C min. 20 ms > 7.5 V DC yes, max / 32 / 130 mm 650 g CE; culus; culusex; curus; EC; TUEV 12 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 7.2 (1 min), 9 (4s) 18 (2ms) 89% > 230 V C min. 20 ms > 18 V DC yes, max / 32 / 130 mm 650 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 3.5 Ordering data PRO MX 70W 5V PRO MX 72W 12V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.18

28 connectpower PROmax connectpower PROmax PRO MX 120W 12V 10 PRO MX 240W 48V 5 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max. 15 6, Char. B, circuit breaker, 6, char. C circuit breaker V C (wide-range input) V C Hz V DC 230 V C / 115 V C 370 VDC / 120 VDC Yes / max , char. B circuit breaker, 6 8, char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 12 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 12 (1 min), 15 (4s) 30 (2ms) 89% > 230 V C min. 20 ms > 18 V DC yes, max / 40 / 130 mm 850 g CE; culus; culusex; curus; EC; TUEV 48 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 5 (1 min), 7.5 (4s) 15 (2ms) 92.5% > 230 V C min. 20 ms V DC yes, max / 60 / 130 mm 1050 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 Ordering data PRO MX 120W 12V PRO MX 240W 48V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.19

29 connectpower PROmax wenlok.com.mx connectpower PROmax PRO MX 480W 48V 10 PRO MX 960W 48V 20 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max , Char. B circuit breaker, 10, char. C circuit breaker V C (wide-range input) V C Hz V DC 230 VC / 115 VC 370 VDC / 120 VDC Yes / max , char. B circuit breaker, 16, Char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 48 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 12 (1 min), 15 (4s), V C 60 (2ms) 93% > 230 V C min. 20 ms V DC yes, max / 90 / 130 mm 2000 g CE; culus; culusex; curus; EC; TUEV 48 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 24 (1 min), 30 (4s), V C 60 (2ms) 94% > 230 V C min. 20 ms V DC yes, max / 140 / 130 mm 1350 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 3 for L/N/PE 8 (++,---,11,13,14) 0.18 / / / / / / x 4.0, PZ x 5.5 Ordering data PRO MX 480W 48V PRO MX 960W 48V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.20

30 connectpower PROmax connectpower PROmax PRO MX3 120W 24V 5 PRO MX3 240W 24V 10 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3*500 VC / 3*400 VC 800 V DC / 450 V DC Yes / max , char. C circuit breaker 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3*500 VC / 3*400 VC 800 V DC / 450 V DC Yes / max Char. C, circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 6 (1 min), 7.5 (4s), V C 15 (2ms) 90% > 3*400 V C min. 20 ms V DC yes, max / 40 / 130 mm 850 g CE; culus; culusex; curus; EC; TUEV 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 12 (1 min), 15 (4s) 30 (2ms) 91.5% > 3*400 V C min. 20 ms V DC yes, max / 60 / 130 mm 1350 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 4 for L1/L2/L3/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x for L1/L2/L3/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 Ordering data PRO MX3 120W 24V PRO MX3 240W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.21

31 connectpower PROmax wenlok.com.mx connectpower PROmax PRO MX3 480W 24V 20 PRO MX3 960W 24V 40 Rated input voltage voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) / Inrush current Recommended back-up fuse 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3*500 VC / 3*400 VC 800 V DC / 450 V DC Yes / max Char. C, circuit breaker 3 x x 500 V C (wide-range input) 3 x x 575 V C / 2 x x 575 V C Hz V DC (max. 500 V DC acc. to UL508) 3*500 VC / 3*400 VC 800 V DC / 450 V DC Yes / max , char. C circuit breaker Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom Continuous output U Rated Power U Rated Pulsed current U Rated General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Protection against reverse voltages from the load Parallel connection option Depth x width x height Weight 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 24 (1 min), 30 (4s) 60 (2ms) 91.5% > 3*400 V C min. 20 ms V DC yes, max / 70 / 130 mm 1600 g CE; culus; culusex; curus; EC; TUEV 24 V DC ± 1 % V (adjustable via potentiometer) < 50 U Nenn, Full Load 60 C 45 C, 70 C 48 (1 min), 60 (4s), V C 120 (2ms) 93.5% > 3*400 V C min. 20 ms V DC yes, max / 140 / 130 mm 3400 g CE; culus; culusex; curus; EC; TUEV Connection data Connection system Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Screwdriver blade 4 for L1/L2/L3/PE 8 (++,---,11,13,14) 0.18 / / / / 4 26 / / x 4.0, PZ x 4.0, PZ 1 4 for L1/L2/L3/PE 8 (++,---,11,13,14) 0.18 / / / / / / x 4.0, PZ x 5.5 Ordering data PRO MX3 480W 24V PRO MX3 960W 24V The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. ccessories.22

32 connectpower PROmax PRO-M: diode, capacity and relay modules CP M DM20 CP M DM Rated input voltage / DC input voltage range current Rated output voltage / voltage Rated (nominal) output U Nom continous output 24 V DC Voltage monitoring / Floating contact Switching thresholds General data Degree of efficiency Depth x width x height / Weight mbient temperature (operational) / Storage temperature Humidity Protection degree / Class of protection / Pollution degree Insulation voltage MTBF Mounting position, installation notice EMC / shock / vibration Noise emission acc. to EN55022 Interference immunity test acc. to 24 V DC / V DC 2 x 10 or 1 x V DC ± 1 % / voltage V 60 C 45 C, 55 C, 70 C Yes, In both inputs / Yes 21.6 V DC, relay is on for Power Good, 20.4 V DC, relay is off for Power Fail > 24 V input voltage 150 / 34 / 130 mm / 0.3 kg -25 C...70 C / -40 C...85 C %, no condensation IP 20 / III, with no ground connection, for SELV / kv /output housing > 500,000 h acc. to IEC 1709 (SN29500 Horizontal on TS35 mounting rail. 50 mm of clearance at top & bottom for air circ. Can mount side by side with no space in between. Class B EN (ESD) EN and EN (fields) EN (burst) EN (surge) EN (conducted) 24 V DC / V DC 2 x 20 or 1 x V DC ± 1 % / voltage V 60 C 45 C, 55 C, 70 C Yes, In both inputs / Yes 21.6 V DC, relay is on for Power Good, 20.4 V DC, relay is off for Power Fail > 24 V input voltage 150 / 60 / 130 mm / 0.6 kg -25 C...70 C / -40 C...85 C %, no condensation IP 20 / III, with no ground connection, for SELV / kv /output housing > 500,000 h acc. to IEC 1709 (SN29500 Horizontal on TS35 mounting rail. 50 mm of clearance at top & bottom for air circ. Can mount side by side with no space in between. Class B EN (ESD) EN and EN (fields) EN (burst) EN (surge) EN (conducted) Resistance to vibration / Shock Electrical safety (applied standards) Electrical machine equipment For use with electronic equipment Safety extra-low voltage Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 1 g according to EN50178 / 15 g In all directions cc. to EN60204 cc. to EN50178 / VDE0160 SELV acc. to EN60950, PELV acc. to EN60204 ccsus; CE; culus; EC; GL; GOSTME25 4 (1+, 2+, 1-, 2-) 4 (3 +, 4 +, 3 -, 4 -) 0.5 / / / / / / 12 1 g according to EN50178 / 15 g In all directions cc. to EN60204 cc. to EN50178 / VDE0160 SELV acc. to EN60950, PELV acc. to EN60204 ccsus; CE; culus; EC; GL; GOSTME25 4 (1+, 2+, 1-, 2-) 4 (3 +, 4 +, 3 -, 4 -) 0.5 / / / / / 6 22 / 6 Ordering data Plastic clip-on foot Metal clip-on foot CP M DM CP M DM CP M DM CP M DM ccessories.23

33 connectpower PROmax wenlok.com.mx PRO-M: diode, capacity and relay modules CP M CP Pulse triggering for circuit breakers: with the Weidmüller capacitance module The following conditions apply to the table entries: mbient temperature of 20 C Inner resistance of the circuit breakers is taken into account Half of the rated current flows to a neighbouring circuit before the short circuit is formed DC-compatible circuit breakers: Siemens 5SY series Power supply + CP module Load 1-2- Distance in m Rated input voltage / DC input voltage range Peak current output / Recovery time for the capacitor Switching thresholds Floating contact General data Depth x width x height / Weight mbient temperature (operational) / Storage temperature Humidity Protection degree Class of protection Pollution degree Insulation voltage MTBF Mounting position, installation notice EMC / shock / vibration Noise emission acc. to EN55022 Interference immunity test acc. to Resistance to vibration / Shock Electrical safety (applied standards) Electrical machine equipment For use with electronic equipment Safety extra-low voltage 24 V DC / V DC Depending on the load (typically 40 for 1 ms) / pprox. 1 sec V DC, relay is on for Power Good, 20.4 V DC, relay is off for Power Fail Yes 150 / 34 / 130 mm / 0.4 kg -25 C...70 C / -40 C...85 C %, no condensation IP 20 III, with no ground connection, for SELV kv /output housing > 500,000 h acc. to IEC 1709 (SN29500 Horizontal on TS35 mounting rail. 50 mm of clearance at top & bottom for air circ. Can mount side by side with no space in between. Class B EN (ESD) EN and EN (fields) EN (burst) EN (surge) EN (conducted) EN (dips) 1 g according to EN50178 / 15 g In all directions cc. to EN60204 cc. to EN50178 / VDE0160 SELV acc. to EN60950, PELV acc. to EN60204 CE; culus; EC; GL Fuse tripping Conductor cross section B6 B mm 2 10 m 1.0 mm 2 14 m 6 m 1.5 mm 2 20 m 9 m 2.5 mm 2 30 m 15 m 4 mm 2 50 m 24 m 6 mm 2 B mm mm mm 2 4 m 2.5 mm 2 6 m 4 mm 2 10 m 6 mm 2 16 m C2 C mm 2 11 m 6 m 1.0 mm 2 14 m 8 m 1.5 mm 2 21 m 12 m 2.5 mm 2 34 m 19 m 4 mm 2 32 m 6 mm 2 C6 C mm 2 3 m 1.0 mm m 2 m 1.5 mm m 3 m 2.5 mm 2 9 m 5 m 4 mm 2 14 m 8 m 6 mm 2 12 m Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 4 (++--) 3 (CO contacts) 0.5 / / / / / / 12 For low-impedance connections we recommend 2.5. Ordering data Plastic clip-on foot Metal clip-on foot CP M CP CP M CP ccessories.24

34 .25

35 wenlok.com.mx connectpower PROmax PRO-M: pplication solution for wind power Switched-mode power supply with wide-range input pplication solution for wind power: V DC input larm contact Metal snap-on foot % { \u General technical data characteristic curve / current limit Earth discharge current mbient temperature (operational) / Storage temperature / Start-up Max. permitted humidity (operational) Degree of protection Class of protection Pollution degree Insulation voltage MTBF Protection against reverse voltages from the load Can be connected in parallel Housing version Signal indication Mounting position, installation notice Voltage derating 110 Pout [% Pn] DC [V] Temperature derating EMC / shock / vibration Noise emission acc. to EN55022 Noise immunity tests acc. to Pout [% Pn] mbient temperature [ C] Limiting of mains voltage harmonic currents Resistance against vibration and shock Electrical safety (applied standards) Electrical equipment of machines Safety transformers for switched-mode power units Safety transformers for switched-mode power units Safety extra low voltage Protective separation / protection against electrical shock Protection against dangerous shock currents IU / > 120 % IR < 3.5 m 25 C +70 C / 40 C +85 C / 40 C 5 % 95 % RH IP 20 I, with PE connection 2 3 kv C 1 min. / 2 kv C 1 min. / 0.5 kv C 1 min. > 500,000 h according to IEC 1709 (SN29500) V DC Yes, without diode module Metal, corrosion resistant Operations, green/red LED Horizontal on TS 35 mounting rail, with 50 mm of clearance at top and bottom for air circulation. Can be mounted side by side with no space in between. Suitable for installation in rotating systems. Class B EN (ESD), EN and EN (Fields), EN (Burst), EN (Surge), EN (conducted), EN (Dips) according to EN according to EN50178, Shock: 5 g in all directions according to EN60204 according to EN according to EN50178 / VDE0160 SELV according to EN60950, PELV according to EN60204 VDE / according to DIN according to VDE

36 connectpower PROmax PRO-M: application solutions for wind power CP M SNT 250W 24V 10 UW Rated input voltage / voltage range C Frequency range C DC input voltage range C current consumption DC current consumption fuse (internal) Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency Power factor (approx.) C failure bridging I Nom Depth x width x height / Weight dditional equipment Status indicator Relay on/off V C (wide-range input) / V C 100 V C) Hz V DC 230 V C / 115 V C 370 V DC / 120 V DC Yes 4 / DI, safety fuse 10, Char. B, circuit breaker 3...4, Char. C, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) < 50 mv 24 V DC, I N, < 2,4 V 24 V DC, I -40 C 60 C 45 C, 55 C, 70 C V C / V C > 230 V C / > 115 V C > V C / > V C 155 / 60 / 130 mm / 1.2 Kg Green LED, red LED voltage > 21.6 V / < 20.4 V CE; culus; EC; GL; GOSTME25; TUEV Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 6 (+,+,-,-,COM,NO) 0.5 / / / / / / 12 Ordering data CP M SNT 250W 24V 10UW ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..27

37 connectpower PROmax - ccessories wenlok.com.mx Small metal foot Large metal foot Small plastic foot Large plastic foot Type Order No. MT 30 MF Type Order No. MT 45 MF Type Order No. MT 30 BK Type Order No. MT 45 BK Small wall mounting Large wall mounting Type Order No. CP WLLDPTER 30 MM Type Order No. CP WLLDPTER 45 MM Small screwdriver Large screwdriver Type Blade type Size/F a b c Order No. SDIK PH SDIS 0.5X3.0X100 B Type Blade type Size/F a b c Order No. SDIS 1.0X5.5X125 B Markers Endwinkel For DIN rail TS 35 Type Colour Qty. Order No. SM 18/9.5 K MC NE WS white Polyamide with fibre glass, screwable Colour Torque Qty. Order No. WEW 35/1 SW black 1.2 Nm

38 .29

39 wenlok.com.mx connectpower PRO-H connectpower PRO-H % { \ CB Scheme L (+) N ( ) C DC PE General technical data Current limiting mbient temp. operating / storage temperature Max. perm. air humidity (operation) Degree of protection / Class of protection Pollution degree Insulation voltage input/output MTBF according to IEC DC OK Data Link > 100 % Irated C -25 C +85 C 95 % RH IP 20 / I, with PE connection 2 4 kv I/O 2 kv I/earth 0.5 kv O/earth CP T 70/90 W > 1.8 Mio. h CP T 140 W > 1.2 Mio. h CP T 180/360/600 W > 0.9 Mio. h 16 V DC / 35 V DC / 63 V DC yes, without diode module metal, corrosion resistant Thermal protection, autom. restart Unlimited, autom. restart Dual LED Operational: Green LED; Error: Red LED Horizontal on TS 35 mounting rail, with 80 mm space at top and bottom. Side by side mounting with 50 mm clearance. 7 mm Protection against reverse voltages from the load Parallel connection option Housing version Overload protection Short circuit protection Indication Mounting position, installation notice Stripping length (rated connection) Signal indication Power Good Signal Trigger point 12 V Version 9 11 V DC 24 V Version V DC 48 V Version V DC NO contact 30 V DC / 1.0 max. for 12/24 V DC modules 48 V DC/ 0.5 max. for 36/48 V DC modules 70 W 11 V DC ± 1 V DC / 20 m max. 140 W 11 V DC ± 1 V DC / 40 m max. 90 W 22 V DC ± 2 V DC / 10 m max. 180/360/600 W 24 V DC 22 V DC± 2 V DC / 20 m max. 180/360/600 W 48 V DC 44 V DC± 4 V DC / 15 m max. Potential free, floating signal contact ctive output signal Max. limiting average on state current [] Type\Temp. 1 ph 12 V / 6 1 ph 12 V / 12 1 ph 24 V / ph 24 V / ph 24 V / 15 1 ph 24 V / 25 1 ph 36 V / ph 48 V / 2 1 ph 48 V / 4 1 ph 48 V / ph 48 V / ph 24 V / ph 24 V / ph 24 V / C C C C EMC / shock / vibration Noise emission acc. to EN55022 Noise immunity tests acc. to Class B EN (ESD), EN and EN (Fields), EN (Burst), EN (Surge), EN (conducted), EN (Dips) according to EN axes, Sinus, Hz, 1 g, 1 oct./min 3 axes, 15 g, half sinus, 11 ms Limiting of mains voltage harmonic currents Vibration IEC Shock IEC Electrical safety (applied standards) Electrical equipment of machines Safety transformers for switched-mode power units Machinery with electronic equipment Safety extra low voltage according to EN60204 according to EN according to EN50178 SELV according to EN60950 CP T SNT W W 180 W 360 W Temperature [ C] W 140 W Power [% Pmax] Power [% Pmax] Voltage [V C]

40 connectpower PRO-H connectpower PRO-H CP T SNT 70W 12V 6 CP T SNT 140W 12V 12 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (wide-range input) V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 12 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 12 V DC, I nom 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 35 / 110 mm 0.5 kg BVTEX; CE; CS; curus; EC; UL V C (auto-select) V C, V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 12 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 12 V DC, I nom 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 54 / 110 mm 0.7 kg BVTEX; CE; CS; curus; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 2 (+ / -) 0.5 / / / / / / 12 3 for L/N/PE 7 (+ / - / Signal) 0.5 / / / / / / 12 Ordering data CP T SNT 70W 12V CP T SNT 140W 12V The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.31

41 connectpower PRO-H wenlok.com.mx connectpower PRO-H CP T SNT 90W 24V 3.8 CP T SNT 90W 24V 3.8 CL2 Class 2, UL 1310 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (wide-range input) V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 35 / 110 mm 0.5 kg BVTEX; CE; CS; curus; EC; UL V C (wide-range input) V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 35 / 110 mm 0.5 kg CE; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 2 (+ / -) 0.5 / / / / / / 12 3 for L/N/PE 2 (+ / -) 0.5 / / / / / / 12 Ordering data CP T SNT 90W 24V 3, CP T SNT 90W 24V3,8CL The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.32

42 connectpower PRO-H connectpower PRO-H CP T SNT 180W 24V 7.5 CP T SNT 360W 24V 15 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (auto-select) V C, V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 54 / 110 mm 0.7 kg BVTEX; CE; CS; curus; EC; UL V C (auto-select) V C, V C Hz 230 V C, 115 V C 6.3 / < 25 (230 V C) 10 16, char. B, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 80 / 110 mm 1.1 kg BVTEX; CE; CS; curus; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 7 (+ / - / Signal) 0.5 / / / / / / 12 3 for L/N/PE 7 (+ / - / Signal) 0.5 / / / / / / 12 Ordering data CP T SNT 180W 24V 7, CP T SNT 360W 24V The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.33

43 connectpower PRO-H wenlok.com.mx connectpower PRO-H CP T SNT 600W 24V 25 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (auto-select) V C, V C Hz 230 V C, 115 V C 12 / < 30 (230 V C) 16 25, char. B, circuit breaker 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 165 / 125 mm 2.8 kg BVTEX; CE; CS; curus; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 7 (+ / - / Signal) 1 / 4 1 / / / 4 18 / / 10 Ordering data CP T SNT 600W 24V ccessories The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system..34

44 connectpower PRO-H connectpower PRO-H CP T SNT 90W 48V 2 CP T SNT 180W 48V 4 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (wide-range input) V C Hz 230 V C, 115 V C 4 / < 20 (230 V C) 6 16, char. B, circuit breaker 48 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 48 V DC, I Nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 35 / 110 mm 0.5 kg BVTEX; CE; EC; UL V C (auto-select) V C, V C Hz 230 V C, 115 V C 4 / < 25 (230 V C) 6 16, char. B, circuit breaker 48 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 48 V DC, I Nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 54 / 110 mm 0.7 kg BVTEX; CE; CS; curus; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 2 (+ / -) 0.5 / / / / / / 12 3 for L/N/PE 7 (+ / - / Signal) 0.5 / / / / / / 12 Ordering data CP T SNT 90W 48V CP T SNT 180W 48V The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.35

45 connectpower PRO-H wenlok.com.mx connectpower PRO-H CP T SNT 360W 48V 7.5 CP T SNT 600W 48V 12.5 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (auto-select) V C, V C Hz 230 V C, 115 V C 6.3 / < 25 (230 V C) 10 16, char. B, circuit breaker 48 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 48 V DC, I Nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 80 / 125 mm 1.1 kg BVTEX; CE; CS; curus; EC; UL V C (auto-select) V C, V C Hz 230 V C, 115 V C 12 / < 30 (230 V C) 16 25, char. B, circuit breaker 48 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 48 V DC, I Nenn 40 C 40 C, 60 C, 70 C typ V C min V C, min V C yes, max / 165 / 125 mm 2.8 kg BVTEX; CE; CS; curus; EC; UL Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 7 (+ / - / Signal) 0.5 / / / / / / 12 3 for L/N/PE 7 (+ / - / Signal) 1 / 4 1 / / / 4 18 / / 10 Ordering data CP T SNT 360W 48V 7, CP T SNT 600W 48V 12, The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.36

46 connectpower PRO-H connectpower PRO-H CP T SNT2 180W 24V 7.5 CP T SNT2 360W 24V 15 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (switchable) V C, V C 50 / 60 Hz / < 230 V C 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 60 C, 70 C typ. 88 % min. 20 ms Yes 110 / 54 / 110 mm 0.7 kg CE; EC V C (switchable) V C, V C 50 / 60 Hz / < 230 V C 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 70 C, 60 C typ. 88 % min. 20 ms Yes 125 / 80 / 125 mm 1.1 kg CE; EC Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 4 (++ / --) 1 / / 4 1 / / 4 18 / / 10 The device is suitable for single-phase and two-phase operation. 3 for L/N/PE 4 (++ / --) 1 / / 4 1 / / 4 18 / / 10 The device is suitable for single-phase and two-phase operation. Ordering data CP T SNT2 180 W 24 V 7, CP T SNT2 360 W 24 V The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. ccessories.37

47 connectpower PRO-H wenlok.com.mx connectpower PRO-H CP T SNT2 600W 24V 25 L (+) N ( ) PE C 13 Data 14 DC Link + DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight V C (switchable) V C, V C 50 / 60 Hz / < 230 V C 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 40 C, 40 C, 70 C typ. 88 % min. 20 ms Yes 125 / 190 / 125 mm 3 kg CE; EC Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 3 for L/N/PE 5 (++ / ---) 1 / / 4 1 / / 4 18 / / 10 The device is suitable for single-phase and two-phase operation. Ordering data CP T SNT2 600 W 24 V ccessories The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system..38

48 connectpower PRO-H connectpower PRO-H CP T RM 10 CP T RM 20 1 Data Link PS1 Data Link PS2 1 Data Link PS1 Data Link PS2 Control Control 2 Remote ON/OFF DC OK 2 Remote ON/OFF DC OK Rated input voltage voltage range C Frequency range C C current consumption fuse (internal) / Inrush current Recommended back-up fuse Rated output voltage voltage Residual ripple, breaking spikes Rated (nominal) output U Nom continous output 24 V DC General data Degree of efficiency C failure bridging I Nom Parallel connection option Depth x width x height Weight 24 V DC 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 110 / 35 / 110 mm 0.4 kg CE; CS; curus; EC; GOSTME25 24 V DC 24 V DC ± 1 % V DC (adjustable via potentiometer on front) 100 mv 24 V DC, I nenn 40 C 110 / 54 / 110 mm 0.45 kg CE; CS; curus; EC; GOSTME25 Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 4 (++--) 4 (++ / --) 1 / / 4 1 / / 4 18 / / 10 4 (++--) 4 (++ / --) 1 / / 4 1 / / 4 18 / / 10 Ordering data CP T RM CP T RM ccessories.39

49 connectpower PRO H - ccessories Small screwdriver Type Blade type Size/F a b c Order No. SDIK PH SDIS 0.5X3.0X100 B Large screwdriver Type Blade type Size/F a b c Order No. SDIK PH SDIS 1.0X5.5X125 B Markers End bracket For DIN rail TS 35 Type Colour Qty. Order No. SM 18/9.5 K MC NE WS white Polyamide with fibre glass, screwable Colour Torque Qty. Order No. WEW 35/1 SW black 1.2 Nm

50 connectpower PRO-H (4.33) 35.0 (1.38) s ON V 38.5 (1.52) (4.33) (4.33) 54.0 (2.13) DC 24 V / 25 s ON V 38.5 (1.52) (4.33) DC IN 1 DC IN (3.15) DC IN 1 DC IN (3.15) 5.0 (0.20) 25.0 (0.98) 5.0 (0.20) 5.0 (0.20) 25.0 (0.98) 14.5 (0.57) 54.0 (2.13) (4.33) DC ON O/P DJ. DC OK (4.33) S P wenlok.com.mx PRO-H Dimensional drawings CP T RM 10 CP T RM 20 CP T SNT 70 W / 90 W CP T SNT 180 W / 140 W 35.0 (1.38) (4.33) DC OK DC ON O/P DJ (1.52) 38.5 (1.52) (4.33) PE N L 80.0 (3.15) PE N L 80.0 (3.15) 5.0 (0.20) 25.0 (0.98) 5.0 (0.20) 5.0 (0.20) 25.0 (0.98) 14.5 (0.57) P/ S P S Remote P/ S Remote.41

51 connectpower PRO-H wenlok.com.mx PRO-H Dimensional drawings CP T SNT 360 W / 480 W (4.92) PE N 80.0 (3.15) DC OK DC ON O/P DJ. L 45.0(1.77) 86.5(3.41) (4.92) CP T SNT 600 W / 960 W 25.0 (0.98) P/ S P S Remote (4.84) 25.0 (0.98) 21.0 (0.83) (6.50) (4.92) 5.0 (0.20) 25.0 (0.98) (1.81) (0.67) 25.0 (0.98) (4.92) 45.0 (1.77) PE N L DC OK DC ON O/P DJ (3.41) Remote P S P/ S.42

52 .43

53 connectpower PRO-E connectpower PRO-E CP E SNT 25W 5V 5 CP E SNT 25W 12V 2.1 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 5 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 25 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH 77 5 V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 240 g CE; curus; EC 0.34 / 4 91 / 51 / 28 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 25 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 240 g CE; curus; EC 0.34 / 4 91 / 51 / 28 mm Ordering data CP E SNT 25W 5V CP E SNT 25W 12V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..44

54 connectpower PRO-E connectpower PRO-E CP E SNT 25W 24V 1.1 CP E SNT 25W 48V 0.57 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 25 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 240 g CE; curus; EC 0.34 / 4 91 / 51 / 28 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 25 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 240 g CE; curus; EC 0.34 / 4 91 / 51 / 28 mm Ordering data CP E SNT 25W 24V CP E SNT 25W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..45

55 connectpower PRO-E connectpower PRO-E CP E SNT 50W 5V 10 CP E SNT 50 W 12V 4.2 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 5 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 50 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH 78 5 V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 310 g CE; curus; EC 0.34 / / 100 / 35 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 50 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 310 g CE; curus; EC 0.34 / / 100 / 35 mm Ordering data CP E SNT 50W 5V CP E SNT 50W 12V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..46

56 connectpower PRO-E connectpower PRO-E CP E SNT 50W 24V 2.2 CP E SNT 50W 48V 1.1 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 50 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 310 g CE; curus; EC 0.34 / / 100 / 35 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 50 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 310 g CE; curus; EC 0.34 / / 100 / 35 mm Ordering data CP E SNT 50W 24V CP E SNT 50W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..47

57 connectpower PRO-E connectpower PRO-E CP E SNT 75W 5V 12 CP E SNT 75W 12V 6 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 5 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 75 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH 76 5 V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 440 g CE; curus; EC 0.34 / / 98.5 / 40 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 75 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 440 g CE; curus; EC 0.34 / / 98.5 / 40 mm Ordering data CP E SNT 75W 5V CP E SNT 75W 12V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..48

58 connectpower PRO-E connectpower PRO-E CP E SNT 75W 24V 3.2 CP E SNT 75W 48V 1.6 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 75 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 440 g CE; curus; EC 0.34 / / 98.5 / 40 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 75 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 440 g CE; curus; EC 0.34 / / 98.5 / 40 mm Ordering data CP E SNT 75W 24V CP E SNT 75W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..49

59 connectpower PRO-E connectpower PRO-E CP E SNT 100W 5V 16 CP E SNT 100W 12V 8.5 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 5 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 100 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH 77 5 V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 590 g CE; curus; EC 0.34 / / 97.5 / 40 mm V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 100 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 590 g CE; curus; EC 0.34 / / 97.5 / 40 mm Ordering data CP E SNT 100W 5V CP E SNT 100W 12V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..50

60 connectpower PRO-E connectpower PRO-E CP E SNT 100W 24V 4.5 CP E SNT 100W 48V 2.3 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 100 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 590 g CE; curus; EC 0.34 / / 97.5 / 40 mm V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 100 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 590 g CE; curus; EC 0.34 / / 97.5 / 40 mm Ordering data CP E SNT 100W 24V CP E SNT 100W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..51

61 connectpower PRO-E connectpower PRO-E CP E SNT 150W 12V 12.5 CP E SNT 150W 24V 6.5 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 150 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 820 g CE; curus; EC 0.34 / / 99 / 40 mm V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 150 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 820 g CE; curus; EC 0.34 / / 99 / 40 mm Ordering data CP E SNT 150W 12V CP E SNT 150W 24V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..52

62 connectpower PRO-E connectpower PRO-E CP E SNT 150W 48V 3.3 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 150 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 820 g CE; curus; EC 0.34 / / 99 / 40 mm Ordering data CP E SNT 150W 48V The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. ccessories.53

63 connectpower PRO-E connectpower PRO-E CP E SNT 250W 12V 21 CP E SNT 250W 24V 10.5 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 12 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 250 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 1080 g CE; curus; EC 0.34 / / 115 / 49.5 mm V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer 24 V DC 250 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 1080 g CE; curus; EC 0.34 / / 115 / 49.5 mm Ordering data CP E SNT 250W 12V CP E SNT 250W 24V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..54

64 connectpower PRO-E connectpower PRO-E CP E SNT 250W 48V 5.2 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V C optional / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 250 W < 100 mv PP 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 1080 g CE; curus; EC 0.34 / / 115 / 49.5 mm Ordering data CP E SNT 250W 48V The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. ccessories.55

65 connectpower PRO-E connectpower PRO-E CP E SNT 350W 24V 14.6 CP E SNT 350W 48V 7.3 voltage current frequency fuse (internal) Recommended back-up fuse voltage voltage adjustment current power Residual ripple, breaking spikes Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output General data mbient temperature (operational) Storage temperature Max. perm. air humidity (operational) Degree of efficiency Status indicator Standards EMC standards Mounting position, installation notice Weight Connection cross-section, solid, min. / max. Depth x width x height V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 24 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 350 W 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 1250 g CE; curus; EC 0.34 / / 115 / 49.5 mm V C / V DC 230 V C / 120 V C Hz yes / max at 230 V C, characteristic curve C 48 V DC ± 10% nominal output voltage tolerance, adjustable with potentiometer V DC 350 W 120~150% Ikonst. of max. output power, automatic restart V DC 20 ms 0.5% Recommended with diode module 0.5 kv 1.5 kv 3 kv -20 C 70 C (>50 C derating,refer derated curve); 70% rated load@70 C -20 C...85 C 5 % 95 % RH V DC Operation, green LED EN EN 55011, EN 55022, EN 55024, EN /-2, -3 Panel mount, screw fix 1250 g CE; curus; EC 0.34 / / 115 / 49.5 mm Ordering data CP E SNT 350W 24V CP E SNT 350W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..56

66 .57

67 connectpower PRO-E wenlok.com.mx Installation drawing CP E SNT 25W CP E SNT 50W Ø M Ø 4 2-M3 Ø Ø M M3 CP E SNT 75W CP E SNT 100W Ø 3.5 Ø M3 Ø 3.5 Ø Ø M Ø M3 3-M Ø Ø CP E SNT 150W 28 Ø M Ø Ø M3.58

68 5-M M3 Ø4.5 wenlok.com.mx connectpower PRO-E Installation drawing CP E SNT 250W and CP E SNT 350W CP E SNT 250W and CP E SNT 350W (with mounting clip) Ø Ø M Ø Ø Ø Ø Ø CP-E-SNT derating curve / ambient temperature CP E SNT 25W up to CP E SNT 350W 100% 80% Load (%) 60% 40% 20% mbient temperature ( C).59

69 connectpower INSTPOWER wenlok.com.mx connectpower Single-phase CP SNT 24W 24V 1 CP SNT 24W 15V 1.5 L C/DC N PWM + DC L N FUSE + L N FUSE + voltage current frequency Turn-on current limit fuse Surge protection voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C, V DC V C; V C 50/ 60 Hz Thermistor 2 time-lag fuse (internal) Varistor 24 V DC 1 24 W < 2 % Surge current / thermal cut-out Varistor V C / V C 0.5% 8000 µf 0.5 kv 1.5 kv 3 kv 4 kv -20 C...50 C -40 C...85 C 78% DIN EN 50178, DIN EN 60950, IEC950 CE; CS; CSEX; culus; EC; GOSTME25 EN /-2, -3 yes, max V C, V DC V C; V C 50/ 60 Hz Thermistor 2 time-lag fuse (internal) Varistor 15 V DC W < 2 % Surge current / thermal cut-out Varistor V C / V C 0.5% 8000 µf 0.5 kv 1.5 kv 3 kv 4 kv -20 C...50 C -40 C...85 C 78% DIN EN 50178, DIN EN 60950, IEC950 CE; CS; culus; EC; GOSTME25 EN /-2, -3 yes, max 2. Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 4 / 0.08 / / 52 / 90.5 Derating loss: C The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. / 4 / 0.08 / / 52 / 90.5 Derating loss: C The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. Ordering data CP SNT 24W 24V CP SNT 24W 15V The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. ccessories.60

70 connectpower INSTPOWER connectpower Single-phase CP SNT 24W 12V 1.5 CP SNT 24W 5V 2 L C/DC N PWM + DC L N FUSE + L N FUSE + voltage current frequency Turn-on current limit fuse Surge protection voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C, V DC V C; V C 50/ 60 Hz Thermistor 2 time-lag fuse (internal) Varistor 12 V DC W < 2 % Surge current / thermal cut-out Varistor V C / V C 0.5% 8000 µf 0.5 kv 1.5 kv 3 kv 4 kv -20 C...50 C -40 C...85 C 78% DIN EN 50178, DIN EN 60950, IEC950 CE; CS; culus; EC; GOSTME25 EN /-2, -3 yes, max V C, V DC V C; V C 50/ 60 Hz Thermistor 2 time-lag fuse (internal) Varistor 5 V DC 2 10 W < 2 % Surge current / thermal cut-out Varistor V C / V C 0.5% 8000 µf 0.5 kv 1.5 kv 3 kv 4 kv -20 C...50 C -40 C...85 C 78% DIN EN 50178, DIN EN 60950, IEC950 CE; CS; culus; EC; GOSTME25 EN /-2, -3 yes, max 2. Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 4 / 0.08 / / 52 / 90.5 Derating loss: C The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. / 4 / 0.08 / / 52 / 90.5 Derating loss: C The internal varistor found in a switch-mode power supply does not replace the need for surge protection within a system. Ordering data CP SNT 24W 12V CP SNT 24W 5V The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system. ccessories.61

71 connectpower INSTPOWER wenlok.com.mx connectpower Single-phase CP SNT 25W 5V 5 L C/DC N PWM + DC L N FUSE + voltage current frequency Turn-on current limit fuse voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C / V DC 500 m at rated 230 V C 50/ 60 Hz Yes Fusible link 2.5 (T) / 250 V V DC (adjustable via potentiometer) 5 25 W 120 mv SS 105 % % I const of max. output load; automatic reset Varistor V C / V C 1% µf 0.5 kv 1.5 kv 3 kv 4 kv C (Derating ab 55 C) -20 C...85 C 70% DIN EN (PELV), DIN EN (SELV) ccsus; curus; EC; GOSTME25; UL EN 55011, EN 55022, EN ,-3, EN ,-3,-4 Max. 3 devices (rated voltages are to be calibrated at ±20 mv) Derating curve Current () mbient temperature ( C) Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 2.5 / 0.5 / / 70 / 90.5 Ordering data CP SNT 25W 5V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..62

72 connectpower INSTPOWER connectpower Single-phase CP SNT 48W 12V 4 L C/DC N PWM + DC L N FUSE + voltage current frequency Turn-on current limit fuse voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C / V DC 500 m at rated 230 V C 50/ 60 Hz Yes Fusible link 2.5 (T) / 250 V V DC (adjustable via potentiometer) 4 48 W 120 mv SS 105 % % I const of max. output load; automatic reset Varistor V C / V C 1% µf 0.5 kv 1.5 kv 3 kv 4 kv C (Derating ab 55 C) -20 C...85 C 75% DIN EN (PELV), DIN EN (SELV) ccsus; CE; curus; EC; GOSTME25; UL EN 55011, EN 55022, EN ,-3, EN ,-3,-4 Max. 3 devices (rated voltages are to be calibrated at ±20 mv) Derating curve Current () mbient temperature ( C) Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 2.5 / 0.5 / / 70 / 90.5 Ordering data CP SNT 48W 12V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..63

73 connectpower INSTPOWER wenlok.com.mx connectpower Single-phase CP SNT 48W 24V 2 L C/DC N PWM + DC L N FUSE + voltage current frequency Turn-on current limit fuse voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C / V DC 500 m at rated 230 V C 50/ 60 Hz Yes Fusible link 2.5 (T) / 250 V V DC (adjustable via potentiometer) 2 48 W 120 mv SS 105 % % I const of max. output load; automatic reset Varistor V C / V C 1% µf 0.5 kv 1.5 kv 3 kv 4 kv C (Derating ab 55 C) -20 C...85 C 78% DIN EN (PELV), DIN EN (SELV) ccsus; curus; EC; GOSTME25; UL EN 55011, EN 55022, EN ,-3, EN ,-3,-4 Max. 3 devices (rated voltages are to be calibrated at ±20 mv) Derating curve Current () mbient temperature ( C) Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 2.5 / 0.5 / / 70 / 90.5 Ordering data CP SNT 48W 24V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..64

74 connectpower INSTPOWER connectpower Single-phase CP SNT 48W 48V 1 L C/DC N PWM + DC L N FUSE + voltage current frequency Turn-on current limit fuse voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Max. capacitance at output Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Standards EMC standards Parallel connection option V C / V DC 500 m at rated 230 V C 50/ 60 Hz Yes Fusible link 2.5 (T) / 250 V V DC (adjustable via potentiometer) 1 48 W 120 mv SS 105 % % I const of max. output load; automatic reset Varistor V C / V C 1% µf 0.5 kv 1.5 kv 3 kv 4 kv C (Derating ab 55 C) -20 C...85 C 80% DIN EN (PELV), DIN EN (SELV) ccsus; curus; EC; GOSTME25; UL EN 55011, EN 55022, EN ,-3, EN ,-3,-4 Max. 3 devices (rated voltages are to be calibrated at ±20 mv) Derating curve Current () mbient temperature ( C) Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 2.5 / 0.5 / / 70 / 90.5 Ordering data CP SNT 48W 48V ccessories The internal varistor found in a switch-mode power supply does not replace the necessary surge protection in a system..65

75 connectpower INSTPOWER - ccessories Small screwdriver Type Blade type Size/F a b c Order No. SDIK PH SDIS 0.5X3.0X100 B Markers End bracket For DIN rail TS 35 Type Colour Qty. Order No. SM 18/9.5 K MC NE WS white Polyamide with fibre glass, screwable Colour Torque Qty. Order No. WEW 35/1 SW black 1.2 Nm

76 connectpower WVEPOWER connectpower Single-phase CP SNT 12W 24V 0.5 L C/DC N PWM + DC voltage current frequency fuse Surge protection voltage current power Max. residual ripple Overload protection Surge protection Mains failure bridge-over time Control at % load Parallel connection option Insulation coordination (EN 50178) electrical isolation, output-earth electrical isolation, input-earth electrical isolation, input-output electrical isolation, I/O rail General data mbient temperature (operational) Storage temperature Degree of efficiency at max. load Status indication Standards EMC standards Power factor correction V C, V DC V C; V C 50/ 60 Hz 2 time-lag fuse (internal) Varistor 24 V DC W 0.1 % Surge current / thermal cut-out Varistor V C / V C 0.6% No 0.5 kv 1.5 kv 3 kv 4 kv C -40 C...85 C 80% Green LED DIN EN 50178, DIN EN 60950, IEC950 IEC /-2, -3 No CE; CS; culus; EC; GOSTME25 Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 2.5 / 0.5 / / 22.5 / 92.4 Ordering data CP SNT 12W 24V ccessories The internal varistor found in a switch-mode power unit does not replace the necessary surge protection in a system. Supply voltage 24 V and 0 V can be cross-connected with ZQV 2.5N/2.67

77 connectpower DC/DC converter wenlok.com.mx connectpower CP DCDC 50W 22-24V 2 CP DCDC 50W 20-24V 2 Chopper Transformer Rectifier and filtering Chopper Transformer Rectifier and filtering voltage fuse voltage current Overload protection General data mbient temperature (operational) Storage temperature Status indication Switching frequency V DC, typ. 24 V DC, ± 15% internal V DC 2 Surge current cut-out with self-reset C (Derating ab 50 C) -40 C...85 C Green LED 200 khz CE; CS; CSEX; culus; EC V DC, typ. 12V DC, ± 15% internal V DC 2 Surge current cut-out with self-reset C (Derating ab 50 C) -40 C...85 C Green LED 200 khz CE; CS; CSEX; culus; EC Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 4 / 0.1 / / 57 / 98 / 4 / 0.1 / / 57 / 98 Ordering data CP DCDC 50W 22-24V CP DCDC 50W 22-24V ccessories Bracket for wall mounting: Bracket for wall mounting:

78 connectpower DC/DC converter CP DCDC 50W 12V 3 Chopper Transformer Rectifier and filtering V DC, typ. 24 V DC, ± 15% internal V DC 3 Surge current cut-out with self-reset C (Derating ab 50 C) -40 C...85 C Green LED 200 khz CE; CS; CSEX; culus; EC / 4 / 0.1 / / 57 / 98 CP DCDC 50W 12V Bracket for wall mounting:

79 connectpower DC/DC converter wenlok.com.mx connectpower CP DCDC 50W 15V 3 CP DCDC 50W 5V 8 Chopper Transformer Rectifier and filtering Chopper Transformer Rectifier and filtering voltage fuse voltage current Overload protection General data mbient temperature (operational) Storage temperature Status indication Switching frequency V DC, typ. 24 V DC, ± 15% internal 15 V DC 3 Surge current cut-out with self-reset C (Derating ab 50 C) -40 C...85 C Green LED 200 khz CE; CS; CSEX; culus; EC V DC, typ. 24 V DC, ± 15% internal 5 V DC 8 Surge current cut-out with self-reset C (Derating ab 50 C) -40 C...85 C Green LED 200 khz CE; CS; CSEX; culus; EC Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm / 4 / 0.1 / / 57 / 98 / 4 / 0.1 / / 57 / 98 Ordering data CP DCDC 50W 15V CP DCDC 50W 5V ccessories Bracket for wall mounting: Bracket for wall mounting:

80 .71

81 connectpower DC/DC converter wenlok.com.mx connectpower DC/DC converter DC voltage converter for preparation and potential isolation in 24 V DC systems Overvoltage category III Class III protection Status of relay contact DC OK transistor output % { \ u Pout [% Pn] Temperature derating mbient temperature [ C] General technical specifications characteristic curve / current limit IU / > 120 % I R Earth discharge current < m mbient temp. Operating / storage temperature 25 C +70 C / 40 C +85 C Max. permitted humidity (operational) 5 % 95 % RH Protection degree IP 20 Class of protection III Contamination degree 2 Insulation voltage 2.5 kv C 1 min. / 1.5 kv C 1 min. / 0.5 kv C 1 min. Overvoltage category III MTBF > 500,000 hrs. according to IEC 1709 (SN29500) Protection against load reverse voltages V DC Parallel capability (without diode module) Yes, max. 5 Mountable side-by-side without gaps Yes Housing version, metal Resistant to corrosion Signal operations LED green / red Mounting position, installation notice Horizontal on TS 35 DIN rail, above and below 50 mm Clearance for air circulation, suitable for aligning without clearance gap For installation in rotating systems Metal clip-on foot Yes EMC / shock / vibration Noise emission according to EN55022 Class B Interference immunity tests, according to EN (ESD), EN and EN (Fields), EN (Burst), EN (Surge), EN (conducted), EN (Dips) Limiting of mains voltage harmonic currents ccording to EN Resistance against vibration and shock ccording to EN50178, shock: 5 g in all directions Electrical safety (applied standards) Electrical equipment of machines ccording to EN60204 Safety transformers for switched-mode power units ccording to EN Machinery with electronic equipment ccording to EN50178 / VDE0160 Safety extra-low voltage SELV according to EN60950, PLEV according to EN60204 Protective separation / protection against electrical shock VDE / according to DIN Protection against dangerous shock currents ccording to VDE ccessories Diode module (for redundant power supply) CP M DM Capacity module (for pulse triggering of circuit breakers) CP M CP

82 connectpower DC/DC converter connectpower DC/DC converter CP DCDC 250W 24V 10 + DC DC + DC OK Rated input voltage / DC input voltage range DC current consumption Inrush current fuse (internal) Recommended back-up fuse Rated output voltage voltage Ramp-up time Residual ripple, breaking spikes Rated (nominal) output U Nom Short-circuit protection / Overload protection 24 V DC, 60 C General data Degree of efficiency Power loss C failure bridging I Nom Tightening torque Reverse polarity protection Depth x width x height / Weight Signalling Status indicator DC OK transistor output 1 (max. load) DC OK transistor output 0 / DC OK short circuit resistant Floating contact Contact load Relay on/off Connection data Wire connection method Number of terminals Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max 24 V DC / V DC Typ.: 11, Max.: 15.5 Max. 10 Yes 16 / DI/II safety fuse, 16, Char. B circuit breaker, 16, Char. C circuit breaker 24 V DC ± 1 % 100 ms < 50 mv 24 V DC, I N 60 C Yes / Yes 12 for 1 min, ED = 5 % typ. 91% Idle: max. 2 W, Nominal load: 24 W > 7 24 V DC Nm Yes 150 / 60 / 130 mm / 1250 g LED green (DC OK): output voltage 21.6 V, LED red (fault): output voltage 20.4 V voltage 21.6 V ( max. 250 m) voltage 20.4 V / Yes Yes max. 30 V DC / 0.5 voltage > 21.6 V / < 20.4 V culus; EC; GL; TUEV 2 for (+ -) 7 for (DCOK, 13,14, ) 0.5 / / / / / / 12 Ordering data CP DCDC 250W 24V ccessories.73

83 .74

84 Contents Uninterruptible power supplies (UPS) Uninterruptible power supplies (UPS) Uninterruptible power supplies (UPS) Overview B.2 UPS control unit B.4 Battery modules B.6 B Buffer modules B.8 B.1

85 Uninterruptible power supplies (UPS) Overview wenlok.com.mx Uninterruptible power supplies (UPS) B Uninterruptible power supplies Weidmüller s uninterruptible power supplies reliably protect 24 V DC consumers from voltage drop-outs and dips, such as those that could occur as a result of mains faults. These products therefore play a key role in increasing systems availability. The buffer module is the perfect solution for bridging short-term power supply failures or dips of up to 100 ms. The capacitor-based technology enables maintenance-free operation, depending on the application, of up to 10 years. The UPS control unit, together with the accompanying battery module and the power supply, form a complete DC UPS system with support times in minutes or hours. The modular construction allows for the overall load to be distributed into non-safe and safe load circuits, such that often a smaller UPS can be designed. huge variety of operating types are available to suit the particular application precisely. remote input to block battery operation, as well as multiple signal outputs, enable remote operation of the UPS. UPS with battery module UPS with buffer module Mains PRO-M C DC Relay and transistor ouput CP DC BUFFER 24V 20 + Buffer module Safe load V DC +24 V DC Non-safe load B.2

86 Uninterruptible power supplies (UPS) Overview Can your facility afford to experience a power failure? llow us to connect you so that you are safe from failure and downtime. Let s connect. Uninterruptible power supplies (UPS) B It is critical to safeguard a facility s power supply in the event of an outage. You cannot do without the important signals from the field, which serve to control the entire process. In addition, you also need to monitor a whole range of functions and performance parameters for your facility. Our highly modular power supply concept will support you in the practical fulfilment of all your requirements. t the same time, we will also familiarise ourselves with your future requirements and provide you with an individual, tailor-made solution, with components that are precisely aligned to work with one another. For a continual, lasting power supply and clean control voltage, we use redundant circuits, selective short-circuit solutions, battery reservoirs and DC/DC converters. nd because lightning and power surges can put an uninterrupted power supply in a production facility at risk, we also provide lightning and overvoltage protection. The VPU series provides unrestricted operation of power supplies and automation devices such as sensors, actuators and control units. The subsequent availability of the power supply means that all devices will restart in a controlled manner. Let s connect. PRO-M Used to save space in automation technology Individual modulation of the output power Up to 5 devices can be switched directly, in parallel Optional diode modules with fault signalling Expanded temperature range 25 C to 70 C UPS control unit Different status relays for status monitoring Direct switchover to battery operation in the event of malfunction utomatic reconnection to load when power recovers Long battery life due to integrated deep discharge protection Optimised charging feature B.3

87 UPS control unit wenlok.com.mx Uninterruptible power supplies (UPS) Two 24 V models in 10 /20 and 40 Temperature-compensated charging feature for long battery life Integrated battery diagnostics including continuous availability test Status relay and additional transistor outputs for remote monitoring Convenient LED displays for easy error analysis B % { \ u Indication Status relay ( max.load 30 V C/DC 0.1 ) Transistor outputs (24 to 27 V DC max. load 150 m) LED status indicator Fault (alarm), battery operation (buff.), charging (charg.) Fault (alarm), battery operation (buff.), charging (charg.) Three-colour LED: battery capacities > 85 % green, > 40 % yellow, > 20 % red, < 20 % red (flashing) Green/yellow LED: normal / buffering Yellow/red LED: temperature alarm / alarm Yellow/red LED: switch-off / battery fault General technical data mbient temperature (operational) 25 C +70 C Storage temperature 40 C +85 C Max. perm. air humidity 5 95 % Protection degree IP 20 Class of protection 3 Pollution severity level 2 Overvoltage category III Insulation voltage input/output to housing/ground 1300 V DC 1 min (typetest) MTBF > 500,000 hours acc. to IEC 1709 Protection against reverse voltages from the load V DC Parallel connection option Yes, only with diode module for redundancy Housing version Metal, corrosion resistant Mounting position, installation notice Horizontal on mounting rail TS 35, 50 mm above and below Space for free movement of air Overload protection Yes Short-circuit protection Yes EMC / shock / vibration Interference emission cc. to EN55022 Class B Interference immunity tests cc.to EN (ESD), EN and EN (fields), EN (burst), EN (surge), EN (conducted), EN (dips) Resistance against vibration and shock cc.to IEC60954 Vibration: 2.3 g, cc.to IEC shock: 30 g in all directions Electrical safety (applied standards) Electrical equipment of machines cc. to EN60204 Safety transformers for switch-mode power supplies cc. to EN Machinery with electronic equipment cc. to EN50178 / VDE0160 Extra-low voltage protection SELV acc. to EN60950, PLEV acc. to EN60204 Block diagram Cabling Interlock 1 Interlock + 2 Temperature 6 Sensor 7 Selector switches Buffer time Battery size DIP switch 10/20 (only ) + 24V DC Battery Capacity Normal / Buffering larm Cut-off / Bat.Failure Bat + + µc Charger 3 larm 4 Buffering 5 Charging larm Buffering Charging V DC Unbuffered DC Load + Buffered DC Load V DC Battery Power Supply DC UPS Battery Module PRO M Series CP DC UPS 24V DC 20/10 CP BTTERY 24V DC.. h CP DC UPS 24V DC Temperature Sensor B.4

88 UPS control unit UPS control unit CP DC UPS 24V 20/10 CP DC UPS 24V 40 Uninterruptible power supplies (UPS) Rated input voltage DC input voltage range current fuse (internal) DC current consumption Reverse polarity protection Rated output voltage voltage Rated (nominal) output U Nom continous output 24 V DC 24 V DC, 60 C Integrated battery charger Charging feature Charging voltage (temperature compensated) Temperature coefficient Charging current Battery availability test Battery module Rated voltage Storage medium Parallel connection option [battery] Operating elements and control inputs current selector switch Selector switch battery Selector switch buffer times DIP switch Remote disconnection (Interlock) Temperature probe General data Buffer times Degree of efficiency Power loss Depth x width x height / Weight 24 V DC V DC 13 (for 10), 23 (for 20) Yes max. 200 m (without battery), max. 0.5 (with fully charged battery) Yes 24 V DC ± 1 % Vo = Vin V normal operation (Imax), Vo = Vin V battery operation (Imax) 60 C 45 C, 60 C, 70 C 24 for 1 min, ED = 5 % IU characteristic curve 27, C - 48 mv / C 0.15 C every minute 24 V 1.3 h, 3.4 h, 7.2 h, 12 h, 17 h, Selectable with rotary switch yes, max 2. 20, h, 3.4 h, 7.2 h, 12 h, 17 h, No Battery, Service 0.5 min, 1 min, 3 min, 5 min, 10 min, 20 min, 30 min, 45 min,, w/0 Inversion of transistor outputs, Operation without temperature probe Yes NTC 100 kω Depending on the connected battery 96% normal mode, battery is being charged, 98% normal mode, battery is charged, 98% buffer mode < 10 W 150 / 66 / 130 mm / 980 g CE; EC; GL; GOSTME V DC 43 Yes max. 200 m (without battery), max. 0.5 (with fully charged battery) Yes 24 V DC ± 1 % Vo = Vin V normal operation (Imax), Vo = Vin V battery operation (Imax) 60 C 45 C, 70 C, 60 C 48 for 1 min, ED = 5 % IU characteristic curve 27, C - 48 mv / C 0.15 C every minute 24 V 3.4 h, 7.2 h, 12 h, 17 h, Selectable with rotary switch yes, max h, 7.2 h, 12 h, 17 h, No Battery, Service 0.5 min, 1 min, 3 min, 5 min, 10 min, 20 min, 30 min, 45 min,, w/0 Inversion of transistor outputs, Operation without temperature probe Yes NTC 100 kω Depending on the connected battery 96% normal mode, battery is being charged, 98% normal mode, battery is charged, 98% buffer mode < 10 W 150 / 66 / 130 mm / 1000 g CE; EC; GL; GOSTME25 B Connection data Wire connection method Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque Nm /output/battery Signal 0.5 / / / / / 6 26 / /output/battery Signal 0.5 / / / / / 6 26 / Ordering data CP DC UPS 24V 20/ CP DC UPS 24V B.5

89 Battery modules Uninterruptible power supplies (UPS) Battery modules Maintenence-free lead-acid batteries from 3.4 h to 17 h Integrated temperature sensor for optimal battery charging Capacity up to 40 / 30 min or 1 / 30 hrs Robust metal housing for wall mounting wenlok.com.mx CP BTTERY 24V DC1.3H CP BTTERY 24V DC3.4H B Rated input voltage Nominal capacity Charging current, max. Overload and short circuit protection Buffer time 10 Buffer time 20 current, max. Parallel connection option Series switching capability Temperature probe General data Battery type Operating life mbient temperature Storage temperature Latest commissioning Max. perm. air humidity (operational) Class of protection Protection degree Vibration DIN rail/wall in accordance with IEC Shock wall acc. to IEC Depth x width x height / Weight 24 V DC 1.3 h fuse 3 min min 15 Yes No NTC 100 kω Maintenance-free GM lead-acid battery C C (Charging); C (Discharging) -15 C...40 C 9 months 5 % 95 % RH III, with no ground connection, for SELV IP / 0.7 g 30 g 124 / 52 / 148 mm / 1500 g culus; EC; GL 24 V DC 3.4 h fuse 11.3 min 5 min 25 Yes No NTC 100 kω Maintenance-free GM lead-acid battery C C (Charging); C (Discharging) -15 C...40 C 9 months 5 % 95 % RH III, with no ground connection, for SELV IP / 0.7 g 30 g 137 / 108 / 144 mm / 3600 g culus; EC; GL Connection data Wire connection method Wire cross-section, rigid min/max Wire cross-section, flexible min/max Wire cross-section, WG/kcmil min/max Tightening torque Nm /output/battery Signal Pluggable screw connection 0.2 / / / / 4 30 / / /output/battery Signal Pluggable screw connection 0.2 / / / / / / Ordering data CP BTTERY 24V DC1.3H CP BTTERY 24V DC3.4H ccessories B.6

90 Battery modules CP BTTERY 24V DC7.2H CP BTTERY 24V DC12H CP BTTERY 24V DC17H Uninterruptible power supplies (UPS) B 24 V DC 7.2 h x25 fuse 26.5 min 11.5 min 50 Yes No NTC 100 kω 24 V DC 12 h 1.8 2x25 fuse 51 min 22.7 min 50 Yes No NTC 100 kω 24 V DC 17 h x25 fuse 81 min 34.2 min 50 Yes No NTC 100 kω Maintenance-free GM lead-acid battery C C (Charging); C (Discharging) -15 C...40 C 9 months 5 % 95 % RH III, with no ground connection, for SELV IP 20 - / 0.7 g 30 g 134 / 162 / 155 mm / 5900 g culus; EC; GL Maintenance-free GM lead-acid battery C C (Charging); C (Discharging) -15 C...40 C 9 months 5 % 95 % RH III, with no ground connection, for SELV IP 20 - / 0.7 g 30 g 134 / 229 / 155 mm / 9220 g culus; EC; GL Maintenance-free GM lead-acid battery C C (Charging); C (Discharging) -15 C...40 C 9 months 5 % 95 % RH III, with no ground connection, for SELV IP 20 - / 0.7 g 30 g 160 / 242 / 178 mm / g culus; EC /output/battery Signal Pluggable screw connection 0.2 / / / / / 6 28 / /output/battery Signal Pluggable screw connection 0.2 / / / / / 6 28 / /output/battery Signal Pluggable screw connection 0.2 / / / / / 6 28 / CP BTTERY 24V DC7.2H CP BTTERY 24V DC12H CP BTTERY 24V DC17H B.7

91 Uninterruptible power supplies (UPS) Buffer modules Buffer modules Maintenance-free UPS on capacitor basis with a capacity to support 20 / 260 ms Parallel switching to increase the output current or support time Status notification via LED and relay contact wenlok.com.mx CP DC BUFFER 24V 20 B Rated input voltage current Max. approved input current Surge protection voltage current current, max. Parallel connection option Overload protection Surge protection Status relay (max. load) Display Status indicator General data Degree of efficiency Insulation voltage, input/output Storage medium Buffer times MTBF mbient temperature (operational) Storage temperature Humidity Depth x width x height / Weight For use with electronic equipment EMC standards 24 V DC V (only at discharge) 24 V Yes, without diode module 22 (only at discharge) V (only at discharge) voltage OK (30 V C/DC 2), Ready for operation (24 V C/ DC 300 m) Green LED 95 % 1 kv Internal condenser 250 ms at 20, 6 s at 1 > 500,000 h acc. to IEC 1709 (SN C...70 C -40 C...85 C %, no condensation 150 / 66 / 130 mm / 1150 g cc. to EN50178 / VDE0160 CE; TUEV; culus; curus Connection data Wire connection method Wire cross-section, rigid min/max Signal Ordering data CP DC BUFFER 24V ccessories B.8

92 Small metal foot Large metal foot wenlok.com.mx UPS control unit - ccessories Small plastic foot Large plastic foot Uninterruptible power supplies (UPS) Type Order No. MT 30 MF Type Order No. MT 45 MF Type Order No. MT 30 BK Type Order No. MT 45 BK B Small wall mounting Large wall mounting Temperature probe Type Order No. CP WLLDPTER 30 MM Type Order No. CP WLLDPTER 45 MM Type Cable length Order No. CP DC UPS TF m CP DC UPS TF m Small screwdriver Large screwdriver Type Blade type Size/F a b c Order No. SDIS 0.5X3.0X100 B Type Blade type Size/F a b c Order No. SDIS 1.0X5.5X125 B Markers End bracket For DIN rail TS 35 Type Colour Qty. Order No. SM 18/9.5 K MC NE WS white Polyamide with fibre glass, screwable Colour Torque Qty. Order No. WEW 35/1 SW black 1.2 Nm B.9

93 Uninterruptible power supplies (UPS) B B.10

94 Contents Fuse protection for 24 V DC circuits Fuse protection for 24 V DC circuits Fuse protection for 24 V DC circuits Overview C.2 WVEGURD C.4 C C.1

95 Fuse protection for 24 V DC circuits Overview wenlok.com.mx Fuse protection for 24 V DC circuits C Fuse protection 24 V DC control voltage has become the standard in the automation industry. Selective fuse protection is often used when the power is being supplied by PLC-guided controllers. It divides the total load into separate, logically connected safety circuits. For example, the CPU, actuators and sensors can be separated in the load circuits. This selective load protection helps to decrease facility downtime and also to simplify troubleshooting. When a disruption (short circuit) occurs on a standard protective system, the entire power supply is interrupted. In a system using selective fuse protection, only the fuse in the one disrupted load circuit is triggered. If the fuse is triggered quick enough so that other loads (and particularly the CPU) can continue functioning properly, then various control algorithms can be used to deal with the disruption. It is then possible to shut down the facility in an orderly and controlled fashion. fundamental problem when using ordinary fuses is that they take a relatively long time to trigger. Usually, a switched-mode power supply is already well over the surgecurrent limit (typically 120 % of I nom ) before its fuse triggers. Ordinary fuses are therefore not suitable for constructing a selective fuse protective system. Such systems present DC fuses with special challenges. They must be able to switch off quickly enough but they must also be able to tolerate the start-up surge currents from consumer loads. Weidmüller s electronic fuses, from our established WVEGURD line, are the answer to both of these challenges: they are quick acting but can also tolerate start-up currents. You can easily implement selective load protection using our WVEGURD models. In addition, Weidmüller s electronic fuses feature a floating alarm contact and a reset input. This allows a PLC controller to query the status of the fuse or to perform an automated reset after troubleshooting. This provides you with a convenient method for remotely maintaining a complex facility. s a result, you save both time and money. C.2

96 Fuse protection for 24 V DC circuits Overview Fuse protection for 24 V DC circuits Resetting BLOCK DIGRM WVEGURD The WVEGURD family can be reset manually or by using an external signal. They can be reset remotely by simply applying a 24 V signal pulse on the reset input. The reset occurs on the falling edge of the signal. : cyclical automatic reset is not permitted and can lead to a malfunction. INPUT 24 V Reset 0V (8) (1) (7) gn re fail (9) (2) (3) OUTPUT 24 V NC contact 50 V uc /0.05 C Signalling red LED displays when the electronic fuse has been triggered. n alert is also sent out over a floating alarm contact. green LED signals that the unit is switched on. The alarm contact uses an NC contact. WVEGURD C.3

97 WVEGURD wenlok.com.mx Fuse protection for 24 V DC circuits 24 V DC V DC 3.15 C INPUT 24 V Reset 0V (8) (1 ) (7 ) gn rt fail OUTPUT (9 ) 24 V (2 ) (3 ) NC contact 50 V uc /0.05 Current ( ) Time (ms) Current ( ) Time (ms) Rated control voltage Rated current Reset Status relay / CO contact Signalling delay General data mbient temperature (operational) Storage temperature Status indication Standards EMC standards Sliding switch 24 V DC 1.6 Impulse > 100 ms +24 V, falling edge ON NC contact, max. 50 V / 0.05 ; for low voltage only! 3.5 ms typ. 0 C...55 C -20 C...85 C LED green: OK, LED red: tripped DIN EN EN 55011, EN , 2, 4 OFF - wait 10 s - ON; on / off ccsus; CE; curus; EC; GOSTME25 24 V DC 3.15 Impulse > 100 ms +24 V, falling edge ON NC contact, max. 50 V / 0.05 ; for low voltage only! 3.5 ms typ. 0 C...55 C -20 C...85 C LED green: OK, LED red: tripped DIN EN EN 55011, EN , 2, 4 OFF - wait 10 s - ON; on / off ccsus; CE; curus; EC; GOSTME25 Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm 2.5 / 0.5 / / 0.5 / / 22.5 / / 22.5 / 72 Periodic auto-reset not permitted; Tu=23 C, Tension single module clamp connection 2.5 / 0.5 / / 0.5 / / 22.5 / / 22.5 / 72 Periodic auto-reset not permitted; Tu=23 C, Tension single module clamp connection Ordering data Tension-clamp connection WGS 24Vdc 1, WGZ 24Vdc 1, WGS 24Vdc 3, WGZ 24Vdc 3, ccessories Supply voltage +24 V and 0 V can be cross-connected with ZQV 2.5 N/2 Supply voltage +24 V and 0 V can be cross-connected with ZQV 2.5 N/2 C.4

98 WVEGURD 24 V DC V DC 8 Fuse protection for 24 V DC circuits INPUT 24 V Reset 0V (8) (1 ) (7 ) gn rt fail OUTPUT (9 ) 24 V (2 ) (3 ) NC contact 50 V uc /0.05 Current ( ) Time (ms) Current ( ) Time (ms) C Rated control voltage Rated current Reset Status relay / CO contact Signalling delay General data mbient temperature (operational) Storage temperature Status indication Standards EMC standards Sliding switch 24 V DC 6.3 Impulse > 100 ms +24 V, falling edge ON NC contact, max. 50 V / 0.05 ; for low voltage only! 3.5 ms typ. 0 C...55 C -20 C...85 C LED green: OK, LED red: tripped DIN EN EN 55011, EN , 2, 4 OFF - wait 10 s - ON; on / off ccsus; CE; curus; EC; GOSTME25 24 V DC 8 Impulse > 100 ms +24 V, falling edge ON NC contact, max. 50 V / 0.05 ; for low voltage only! 3.5 ms typ. 0 C...55 C -20 C...85 C LED green: OK, LED red: tripped DIN EN EN 55011, EN , 2, 4 OFF - wait 10 s - ON; on / off ccsus; CE; curus; EC; GOSTME25 Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm 2.5 / 0.5 / / 0.5 / / 22.5 / / 22.5 / 72 Periodic auto-reset not permitted; Tu=23 C, Tension single module clamp connection 2.5 / 0.5 / / 0.5 / / 22.5 / / 22.5 / 72 Periodic auto-reset not permitted; Tu=23 C, Tension single module clamp connection Ordering data Tension-clamp connection WGS 24Vdc 6, WGZ 24Vdc 6, WGS 24Vdc 8, WGZ 24Vdc 8, ccessories Supply voltage +24 V and 0 V can be cross-connected with ZQV 2.5 N/2 Supply voltage +24 V and 0 V can be cross-connected with ZQV 2.5 N/2 C.5

99 WVEGURD wenlok.com.mx Fuse protection for 24 V DC circuits 24 V DC C INPUT 24 V Reset 0V (8) (1 ) (7 ) gn rt fail OUTPUT (9 ) 24 V (2 ) (3 ) NC contact 50 V uc /0.05 Rated control voltage Rated current Reset Status relay / CO contact Signalling delay General data mbient temperature (operational) Storage temperature Status indication Standards EMC standards Sliding switch 24 V DC adjustable Impulse > 100 ms +24 V, falling edge ON NC contact, max. 50 V / 0.05 ; for low voltage only! 3.5 ms typ. 0 C...55 C -20 C...85 C LED green: OK, LED red: tripped DIN EN EN 55011, EN , 2, 4 OFF - wait 10 s - ON; on / off ccsus; CE; curus; EC; GOSTME25 Derating curve Dynamic tripping characteristic Tripping current: 0.5 Tripping current () Time (ms) Tripping current: 5.0 Tripping current () Time (ms) Dimensions Clamping range (nominal / min. / max.) Depth x width x height mm 2.5 / 0.5 / / 0.5 / / 22.5 / / 22.5 / 72 Periodic auto-reset not permitted; Tu=23 C, Tension single module clamp connection Ordering data Tension-clamp connection WGS 24Vdc WGZ 24Vdc ccessories Supply voltage +24 V and 0 V can be cross-connected with ZQV 2.5 N/2 C.6

100 Contents Unregulated power supplies Unregulated power supplies Unregulated power supplies Overview D.2 compactpower D.4 D D.1

101 Unregulated power supplies Overview wenlok.com.mx Unregulated power supplies D Unregulated power supplies compactpower Compact power supply units are important links in the power supplies for controllers. They are used where processes or control voltages are required that vary from the mains voltage. Transformers provide the electrical isolation between the input circuit and the output circuit. The minimum requirement (to VDE 0550) is 2,000 V. Screw terminals secure the input-side connection to the mains. The single-phase devices are rated for a nominal voltage of 230 ± 15 V, or 400 V ± 15 V, 50/60 Hz, the 3-phase devices for 3 x 400 V ± 5 %. The secondary DC voltage from the transformer is conducted to a bridge rectifier where it is rectified. The pulsating DC voltage is then fed from the rectifier and filtered to a low residual ripple by means of an electrolytic capacitor. This DC voltage is then fed to the output terminal. These are designed as pluggable screw terminals. varistor is integrated in the output circuitry to attenuate voltage peaks. The operating status is indicated by means of a green LED via the output circuit. Devices with 600 W and higher are equipped with a fan. Single-phase unregulated power supplies Three-phase unregulated power supplies D.2

General technical data. Pollution degree 2. EMC / shock / vibration Noise emission acc. to EN Electrical safety (applied standards)

General technical data. Pollution degree 2. EMC / shock / vibration Noise emission acc. to EN Electrical safety (applied standards) power supplies with basic functionality and a high level of reliability Single- and three-phase switched-mode power supply units Slim design Large temperature range from 25 C to 70 C The output voltage

More information

Datasheet. PRO-M Series Power Supplies

Datasheet. PRO-M Series Power Supplies Datasheet PRO-M Series Power Supplies N E W These compact and efficient power supplies are optimized for machinery, with features that include overload resistance and high performance reserves. They also

More information

Data sheet Functional Electronics PRO-M. Power supplies for space-saving use in automation technology

Data sheet Functional Electronics PRO-M. Power supplies for space-saving use in automation technology Data sheet Functional Electronics Power supplies for space-saving use in automation techlogy NE = Power-Reliable-Optimized The optimal and reliable power supply for use in automation techlogie. The solid,

More information

Power supply CP-E 24/2.5

Power supply CP-E 24/2.5 2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment

More information

QUINT-PS/ 3AC/24DC/10

QUINT-PS/ 3AC/24DC/10 Primary-switched power supply with SFB technology, 3 AC, output current 10 A INTERFACE Data sheet 103131_en_01 1 Description PHOENIX CONTACT - 09/2009 Features QUINT POWER power supply units Maximum system

More information

MINI-PS AC/24DC/1.3

MINI-PS AC/24DC/1.3 Power supply unit INTERFACE Data sheet 102894_en_03 1 Description PHOENIX CONTACT 2015-11-17 Features MINI POWER power supplies for MCR technology In measurement and control technology (MCR), modular electronics

More information

Power supply CP-E 24/20.0

Power supply CP-E 24/20.0 2CDC 271 027 F0008 a OUTPUT L+, L+, L, L-: terminals output b INPUT L, N, PE: terminals input c 13-14: terminals - signalling contact d OUTPUT OK: green LED output voltage OK e OUTPUT LOW: red LED output

More information

QUINT-PS/ 3AC/24DC/40

QUINT-PS/ 3AC/24DC/40 Primary-switched power supply unit with SFB technology, 3 AC, output current 40 A INTERFACE Data sheet 103133_en_00 1 Description PHOENIX CONTACT - 07/2009 Features QUINT POWER power supply units Maximum

More information

Power supply CP-T 24/20.0 Primary switch mode power supply

Power supply CP-T 24/20.0 Primary switch mode power supply Data sheet Power supply CP-T 24/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

Power supply CP-E 24/2.5

Power supply CP-E 24/2.5 2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment

More information

Type CP-S, CP-C & CP-A Switch mode

Type CP-S, CP-C & CP-A Switch mode Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting

More information

QUINT-PS-24DC/24DC/10

QUINT-PS-24DC/24DC/10 QUINT-PS-24/24/10 QUINT - converter, primary switched mode, input: 24 V, output: 24 V /10 A INTERFACE Data Sheet PHOENIX CONTACT - 02/2006 Description The QUINT - converter 24 V/10 A converts the voltage

More information

Power supply CP-E 24/0.75

Power supply CP-E 24/0.75 2CDC 271 016 F0t06 a OUTPUT L+, L : terminals output b INPUT L, N, PE: terminals input c LOW: red LED output voltage too low d OK: green LED output voltage OK e OUTPUT Adjust: rotary potentiometer output

More information

Power supply CP-D 24/4.2 Primary switch mode power supply

Power supply CP-D 24/4.2 Primary switch mode power supply Data sheet Power supply CP-D 24/4.2 Primary switch mode power supply The CP-D range of modular power supply units in MDRC design (modular DIN rail components) is ideally suited for installation in distribution

More information

Power supply CP-T 24/10.0 Primary switch mode power supply

Power supply CP-T 24/10.0 Primary switch mode power supply Data sheet Power supply CP-T 24/10.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

Power supply CP-T 48/20.0 Primary switch mode power supply

Power supply CP-T 48/20.0 Primary switch mode power supply Data sheet Power supply CP-T 48/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

CP-T range Product group picture

CP-T range Product group picture Product group picture /1 ABB Catalog Electronic Products and Relays 1/1 2CDC 110 00 C09 Table of contents CP-T range Product group picture /1 Table of contents /2 Benefits and advantages / Ordering details

More information

Power supply CP-E 12/10.0 Primary switch mode power supply Data sheet

Power supply CP-E 12/10.0 Primary switch mode power supply Data sheet 2CDC 271 024 F0008 OUTPUT L+, L+, L-, L-: terminals - output INPUT L, N, PE: terminals - input OUTPUT OK: green LED - output voltage OK OUTPUT LOW: red LED - output voltage too low OUTPUT Adjust: potentiometer

More information

QUINT-PS AC/24DC/40

QUINT-PS AC/24DC/40 Power supply unit INTERFACE Data sheet 102315_en_02 1 Description PHOENIX CONTACT 2010-04-23 Features QUINT POWER power supply units for plant and special engineering reliably start heavy loads with high

More information

Power supply CP-T 24/40.0 Primary switch mode power supply

Power supply CP-T 24/40.0 Primary switch mode power supply Data sheet Power supply CP-T 24/40.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

PHOENIX CONTACT - 05/2008. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area.

PHOENIX CONTACT - 05/2008. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area. Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data Sheet 103129_en_01 PHOENIX CONTACT - 05/2008 1 Description QUINT POWER power supply units highest system availability

More information

Switching power supplies CP range, Linear power supplies CP-L range. Content

Switching power supplies CP range, Linear power supplies CP-L range. Content CP range, Linear power supplies CP-L range Content Switching power supplies, primary switch mode, CP range Benefits and advantages... 136 Approvals... 137 Ordering details... 138 Technical data... 11 Dimensional

More information

Power supply CP-T 48/5.0 Primary switch mode power supply

Power supply CP-T 48/5.0 Primary switch mode power supply Data sheet Power supply CP-T 48/5.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,

More information

CP-E range Benefits and advantages

CP-E range Benefits and advantages Benefits and advantages Characteristics Output voltages 5 V, 12 V, 2 V, 8 V DC Adjustable output voltages Benefits Signalling output/contact Output currents 0.625 A / 0.75 A / 1.25 A / 2.5 A / A / 5 A

More information

Power supply CP-E 48/5.0 Primary switch mode power supply Data sheet

Power supply CP-E 48/5.0 Primary switch mode power supply Data sheet 2CDC 271 028 F0008 OUTPUT L+, L+, L-, L-: terminals - output Features Rated output voltage 48 V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output current 5 A Rated

More information

PHOENIX CONTACT - 06/2008. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area.

PHOENIX CONTACT - 06/2008. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area. Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data Sheet 103383_en_00 1 Description PHOENIX CONTACT - 06/2008 Features QUINT POWER power supply units highest system

More information

TRIO-PS/1AC/24DC/ 5. Extract from the online catalog. Order No.:

TRIO-PS/1AC/24DC/ 5. Extract from the online catalog. Order No.: Extract from the online catalog TRIO-PS/1AC/24DC/ 5 Order No.: 2866310 DIN rail power supply unit, primary-switched mode, 1-phase, output: 24 V DC / 5 A Commercial data EAN 4046356046640 Pack 1 pcs. Customs

More information

CP-T range Benefits and advantages

CP-T range Benefits and advantages Benefits and advantages Characteristics Rated output voltages V, V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output currents 5 A, 10 A, A, A Rated output powers

More information

Primary switch mode power supplies Product group picture

Primary switch mode power supplies Product group picture Primary switch mode power supplies Product group picture /1 ABB Catalog Electronic Products and Relays 2015 2CDC 110 004 C0210 Primary switch mode power supplies Table of contents Primary switch mode power

More information

QUINT-PS/ 1AC/24DC/20

QUINT-PS/ 1AC/24DC/20 Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data sheet 103129_en_04 1 Description PHOENIX CONTACT - 02/2010 Features QUINT POWER power supply units Maximum system

More information

Power supply CP-D 24/1.3

Power supply CP-D 24/1.3 2CDC 271 027 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 24 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 1.3 A Rated output power

More information

Power supply CP-D 12/2.1

Power supply CP-D 12/2.1 2CDC 271 025 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 12 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 2.1 A Rated output power

More information

No-wear isolation of potentials in terminal block design

No-wear isolation of potentials in terminal block design TERMOPTO Overview No-wear isolation of potentials in terminal block design Space saving solid-state relay with PUSH IN connection technology The TERMOPTO opto modules are characterised by a particularly

More information

MINI-PS AC/2X15DC/1

MINI-PS AC/2X15DC/1 MII-PS-100-240AC/2X15DC/1 Power supply unit ITERFACE Data sheet 100299_en_04 1 Description PHOEIX COTACT - 2010-10-20 Features MII POWER is the extremely slim power supply unit with constructional widths

More information

Short-circuit-proof switching amplifier for inductive loads up to 10 A

Short-circuit-proof switching amplifier for inductive loads up to 10 A MICROOPTO Overview Short-circuit-proof switching amplifier for inductive loads up to 10 Powerful, compact solid-state relay with error signalling contact The MICROOPTO family offers the customer high-quality

More information

For Immediate Delivery call KMParts.com at (866)

For Immediate Delivery call KMParts.com at (866) Contents 9/1 Page Description SN4 switched-mode power supply units 9/2 GW4 power supply units 9/3 GD4 power supply units 9/4 Basic Units, Accessories 9/5 Technical data 9/6 Dimensions 9/12 9/2 Description

More information

UNO-PS/1AC/24DC/150W. Primary-switched power supply unit. Data sheet. 1 Description

UNO-PS/1AC/24DC/150W. Primary-switched power supply unit. Data sheet. 1 Description Primary-switched power supply unit Data sheet 106261_en_02 PHOEIX COTACT 2015-05-13 1 Description The power supply makes a worldwide impression thanks to maximum energy efficiency. ow idling losses (o

More information

Electronic timer CT-TGD.22

Electronic timer CT-TGD.22 2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection

More information

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,

More information

Switched mode power supply for DIN rail mounting type SMP23 DC24V/40A

Switched mode power supply for DIN rail mounting type SMP23 DC24V/40A Switched mode power supply for DIN rail mounting type SMP DC4V/40A Description Switched mode power supply (SMP) for rail mounting, three-phase supply voltage, high efficiency, integral input filter and

More information

EMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description.

EMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description. Electronic monitoring relay for voltage monitoring in three-phase networks INTERFACE Data sheet 102110_en_03 1 Description PHOENIX CONTACT - 09/2009 Features Increasingly higher demands are being placed

More information

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC 2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from

More information

EPSITRON Advanced Power Supply System. High-Performance Meets High-Efficiency

EPSITRON Advanced Power Supply System. High-Performance Meets High-Efficiency EPSITRON Advanced Power Supply System High-Performance Meets High-Efficiency WAGO EPSITRON Advanced Pages 4-9 EPSITRON PRO Power Single- and three-phase power supplies with a wide input voltage range and

More information

Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact

Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact Data sheet Electronic timer CT-MVS.12 Multifunctional with 1 c/o (SPDT) contact The CT-MVS.12 is a multifunctional electronic timer from the CT-S range and provides 10 timing functions and 10 time ranges.

More information

Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts The CT-MXS.22 is a multifunctional electronic timer from the CT-S range. It provides 5 timing functions, 2 times 10 time

More information

SITOP power supply: The standard for reliability, compactness, and functionality. Reliably supplies 24 V DC.

SITOP power supply: The standard for reliability, compactness, and functionality. Reliably supplies 24 V DC. SITOP power supply: The standard for reliability, compactness, and functionality Reliably supplies www.usa.siemens.com/sitop Always available, always safe: SITOP A reliable, constant supply of power is

More information

Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 320VAC 360VAC 400VAC 400VAC

Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 320VAC 360VAC 400VAC 400VAC Features DIN-Rail 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection Parallel

More information

Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact

Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact Data sheet Electronic timer CT-TGD.12 Pulse generator with 1 c/o (SPDT) contact The CT-TGD.12 is an electronic time relay with the function pulse generator. It is from the CT-D range. With their MDRC profile

More information

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.22 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.

More information

Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts

Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-WBS.22 Impulse generating and flashing with 2 c/o (SPDT) contacts The CT-WBS.22 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions

More information

TRIO-PS-2G/1AC/24DC/5

TRIO-PS-2G/1AC/24DC/5 TRIOPS2G/1AC/24DC/5 Power supply unit Data sheet 105900_en_01 PHOENIX CONTACT 20150831 1 Description TRIO POWER power supplies with standard functionality The power supplies of the TRIO POWER family convince

More information

Power Supplies 3. SDN-C Compact DIN Rail Series

Power Supplies 3. SDN-C Compact DIN Rail Series SDN-C Compact DIN Rail Series The SDN-C DIN rail power supplies are the next generation of the popular SDN series. These models combine high efficiency and compact size with new visual diagnostic LEDs

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with OFF-delay and 10 time ranges. All electronic timers from the CT-S

More information

Switched mode power supply for DIN rail mounting type SMP21 DC24V/10A

Switched mode power supply for DIN rail mounting type SMP21 DC24V/10A Switched mode power supply for DIN rail mounting type SMP2 DC24V/0A Description Switched mode power supply for rail mounting, with independent change-over of input voltages (AC 5/20 V), integral passive

More information

Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 400VAC

Notes: Note1: Efficiency is tested at nominal input and full load at +25 C ambient. Output Voltage 400VAC 400VAC Features DIN-Rail Description 2 and 3-phase operation Input voltage range: 320 575VAC Output trim range: 22.5 29.5VDC High electrical strength; high reliability Permanent overload and short-circuit protection

More information

ADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W

ADC5000 SERIES. AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications. 60W, 125W and 250 W ADC5000 SERIES AC/DC Switch Mode Power Supplies and Rectifiers for Industrial and Telecom Applications 60W, 125W and 250 W Input voltage 230/115 VAC voltages 12, 24, 36 or 48 VDC Statistical MTBF >3 000

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with true OFF-delay and 10 time ranges. All electronic timers from

More information

05/09/2012

05/09/2012 17.5 mm EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer ON LED) Option

More information

Output Voltage* (nom.)(adjustable)

Output Voltage* (nom.)(adjustable) Industrial Power Supplies TIB Series, 80 480 W Slim profile, reduced module width High Power Factor up to 99% High efficiency up to 94% True back power immunity Low heat dissipation 150% peak current Automatic

More information

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.23 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.

More information

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 For single-phase AC/DC currents The CM-SRS.1 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

LDW240 Series are single, two or three phase DIN Rail Switching Power Supplies.

LDW240 Series are single, two or three phase DIN Rail Switching Power Supplies. LDW240 Series are single, two or three phase DIN Rail Switching Power Supplies. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes

More information

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages Data sheet Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages The CM-EFS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications.

LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications. LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications. Its compact size, high efficiency, excellent reliability together with easy

More information

PHOENIX CONTACT - 09/2009

PHOENIX CONTACT - 09/2009 Electronic miniature circuit-breaker CLIPLINE Data sheet 03906_en_0 PHOENIX CONTACT - 09/2009 Description The EC-E... electronic miniature circuit-breaker selectively protects all 24 V DC load circuits

More information

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Power Supplies. SCL Series. Features. Related Products. Applications

Power Supplies. SCL Series. Features. Related Products. Applications SDN Series The SDN family of DIN Rail power supplies have industry leading performance with a true industrial grade design and high quality that meets difficult industrial environmental conditions including

More information

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 For single-phase AC/DC currents The CM-SRS.2 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

08/07/2015

08/07/2015 17.5 mm - 1 Solid State Relay 0.7A MUS2 Part number 88827004 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external

More information

ECP225-A Series. 225 Watts. AC-DC Power Supplies. Models & Ratings

ECP225-A Series. 225 Watts.  AC-DC Power Supplies. Models & Ratings ECP225- Series C-DC Power Supplies 225 Watts Low Profile High Power Density 3 by 5.0 Footprint 50 W Convection/ 225 W Force Cooled Ratings 5 V Standby and 2 V Fan Outputs Medical and ITE pprovals High

More information

Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages For the monitoring of voltages in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Three-phase monitoring relay CM-PFS

Three-phase monitoring relay CM-PFS Data sheet Three-phase monitoring relay CM-PFS The CM-PFS is a three-phase monitoring relay that is used to monitor three phase mains for incorrect phase sequence and phase failure. All devices are available

More information

Electronic timer CT-SDD.22

Electronic timer CT-SDD.22 CDC 099 F0t0 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied W

More information

Single or parallel use selectable by user Adjustable output voltage. New narrow width saves panel space

Single or parallel use selectable by user Adjustable output voltage. New narrow width saves panel space 4 Power Supplies The SolaHD Difference Rugged metal packaging Multiple output connections for ease of wiring multiple devices New visual diagnostic LEDs show input and output status (see table below) Large,

More information

02/11/2015

02/11/2015 35 mm - 2 Relays 8A PL2R1 Part number 88867455 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external

More information

02/11/2015

02/11/2015 35 mm - 1 Relay 8A OUR3 Part number 88867103 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external

More information

Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Industrial Power Supplies

Industrial Power Supplies Industrial Power Supplies Enduring High Quality Products 24 Volt Industrial Din Rail 120W to 480W Description: With built-in PFC 85% - 90% efficiency 60% power boost ability 23.5V to 29V adjustable output

More information

Liquid level monitoring relay CM-ENS.2x

Liquid level monitoring relay CM-ENS.2x Data sheet Liquid level monitoring relay CM-ENS.2x The CM-ENS.2x is served to regulate and control liquid levels and ratios of mixtures of conductive fluids. It can be used for overflow protection, dry

More information

Output Voltage nom. (adjustable)

Output Voltage nom. (adjustable) Industrial Power Supplies TIB Series, 80 480 W Slim profile, for DI-rail mounting Alternative side-mounting for flat panels High power factor by active power correction Very high efficiency up to 94.5%

More information

TSX Series. Modicon Manuals. Presented by: Modicon PLC. Schneider Electric Quantum Modicon Gould Gettys

TSX Series. Modicon Manuals. Presented by: Modicon PLC. Schneider Electric Quantum Modicon Gould Gettys TSX Series Modicon Manuals Presented by: Modicon PLC Schneider Electric Quantum Modicon Gould Gettys For Product Needs: Email: sales@modiconplc.com Call: 1-800-691-8511 Fax: 919-415-1614 ModiconPLC.com

More information

DSA150 Series. xxx Series. 150 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125.

DSA150 Series. xxx Series. 150 Watts.   AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125. 15 Watts xxx Series Ultra Slim Design 15% Peak Load for 3 seconds Ambient Operation from -1 C to +7 C High Efficiency Selectable Overload Characteristic Selectable Remote Inhibit or Enable 3 Year Warranty

More information

08/07/2015

08/07/2015 17.5 mm - 1 Relay 8A MUR1 Part number 88827105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external load connection

More information

LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply.

LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply. LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes

More information

Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800)

Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) Primary switched-mode power supply units In standard machine production, the requirements for a power supply unit are mostly specified in advance. Here, the TRIO POWER power supply units are suitable which

More information

Switching Power Supply Type SPP1 60W Enclosed type

Switching Power Supply Type SPP1 60W Enclosed type Type SPP1 60W Enclosed type Universal AC input full range Short circuit protection Internal input filter High efficiency High average efficiency (meets ErP) Low stand-by power consumption CE, TUV, and

More information

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Electronic timer CT-MFS.21

Electronic timer CT-MFS.21 2CDC 251 053 F0t07 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c Rotary switch for the preselection of the

More information

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet CDC 0 F0t07 Features Rated control supply voltage -8 V DC, -0 V AC Single-function timer with star-delta change-over One device includes 7 time ranges (0.0 s - 0 min) n/o contacts LEDs for status indication

More information

18V 35V 65V 40A 60A 1.5W 1.2W ms 40ms. 20ms 20ms

18V 35V 65V 40A 60A 1.5W 1.2W ms 40ms. 20ms 20ms Features DIN Rail Description Universal AC Input (85264VAC) Protections: SCP, OVP, OLP, OTP DC OK Indicator LED with Relay Contacts 5% (8W) peak load capacity Builtin active PFC,PF>,95 High effciency up

More information

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents The CM-SRS.M1 is an electronic current monitoring relay that monitors single-phase mains (DC or AC) for over- and undercurrent

More information

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units BETA Switching Transformers, Bells and Socket Outlets /2 Product overview /3 4AC3 0, 4AC3 1 bell transformers /5 4AC3 4... 4AC3 transformers for permanent loads /8 4AC2 4 power supply units / 7LQ2 2 bells

More information

CB Scheme UL508 UL ATEX II3G

CB Scheme UL508 UL ATEX II3G Industrial Power Supplies UL Hazloc Class I, division 2 approval and ATEX certification SEMI F47 compliant for voltage sag immunity Rugged metal case with optional side-mounting Very high efficiency up

More information

420 W High Line Output Power. Rugged Industrial Construction. -40 C to +70 C Operation. 5 V Standby. Screw Terminals. SEMI F47 Compliant

420 W High Line Output Power. Rugged Industrial Construction. -40 C to +70 C Operation. 5 V Standby. Screw Terminals. SEMI F47 Compliant SHP350 Series 420 W High Line Output Power Rugged Industrial Construction Variable Speed Fan for Noise Reduction -40 C to +70 C Operation AC OK, Remote On/Off and Active Current Share Screw Terminals SEMI

More information

Smart Power Relay E I...

Smart Power Relay E I... Smart Power Relay E-48-8I... Description The Smart Power Relay E-48-8I.- is a remotely controllable electronic load disconnecting relay with three functions in a single unit: l electronic relay l electronic

More information

Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages

Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages Data sheet Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages The CM-ESS.M is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Solid-State Soft Starters

Solid-State Soft Starters Selection and ordering data Rated operational voltage U e V Soft starters for three-phase asynchronous motors 3RW30 25-1B14 3RW30 35-1B14 t ambient temperature 40 C Size Order No. Price Weight Pack. Rated

More information

Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts

Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-MBS.22 Multifunctional with 2 c/o (SPDT) contacts The CT-MBS.22 is a multifunctional electronic timer from the CT-S range. It provides 10 timing functions and 10 time ranges.

More information

Related Products SDP Series SFL Series SCP Series SCL Series SDU UPS

Related Products SDP Series SFL Series SCP Series SCL Series SDU UPS 4 Power Supplies SDN-P DIN Rail Series The SDN DIN Rail power supplies provide industry leading performance. Sag Immunity, transient suppression and noise tolerant, the SDN series ensures compatibility

More information

Model Number Structure. Ordering Information. Solid-state Power OFF-delay Timer H3DE-H. Model Number Legend. List of Models

Model Number Structure. Ordering Information. Solid-state Power OFF-delay Timer H3DE-H. Model Number Legend. List of Models Solid-state Power OFF-delay Timer H3DE-H Timers Two delay-time models available. 0.1 to 12 seconds (S Series) 1 to 120 seconds (L Series) Covers wide range of supply voltage. Model Number Structure Model

More information