RSP-750_ EH RSP-750 series. 750W Power Supply with Single Output. File Name:RSP-750-SPEC

Transcription

1 RSP-750_ EH W Power Supply with Single Output File Name:RSP-750-SPEC

2 RSP-750_ EH W Power Supply with Single Output SPECIFICATION MODEL OUTPUT INPUT PROTECTION FUNCTION ENVIRONMENT SAFETY & EMC (Note 4) OTHERS NOTE RSP RSP-750- RSP RSP RSP RSP DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER 5V 00A 0 ~ 00A 500W V 6.5A 0 ~ 6.5A 750W 5V 50A 0 ~ 50A 750W 4V 3.3A 0 ~ 3.3A 75.W 7V 7.8A 0 ~ 7.8A 750.6W 48V 5.7A 0 ~ 5.7A 753.6W RIPPLE & NOISE (max.) Note. 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p 50mVp-p VOLTAGE ADJ. RANGE 4.75 ~ 5.5V 0 ~ 3.5V 3.5 ~ 6.5V 0 ~ 6.4V 4 ~ 30V 43 ~ 55V VOLTAGE TOLERANCE Note.3 ±.0% ±.0% ±.0% ±.0% ±.0% ±.0% LINE REGULATION ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% REGULATION ±.0% ±0.5% ±0.5% ±0.5% ±0.5% ±0.5% SETUP, RISE TIME 000ms, 50ms at full load HOLD UP TIME (Typ.) 6ms/30VAC 6ms/5VAC at full load VOLTAGE RANGE Note.5 90 ~ 64VAC 7 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.97/30VAC 0.98/5VAC at full load EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER OVER VOLTAGE (OVP) OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down OUTPUT VOLTAGE PROGRAMMABLE(PV) Adjustment of output voltage is allowable to 40 ~ 0% of nominal output voltage. Please refer to the Function Manual. CONSTANT CURRENT LEVEL PROGRAMMABLE(PC) Adjustment of constant current level is allowable to 40 ~ 0% of rated current. Please refer to the Function Manual. AUXILIARY POWER 0.A ; tolerance : ± 0% CONTROL Power on : short between Remote (pin3) & V-AUX(pin4) on Power off : open between Remote (pin3) & -AUX(pin4) on DC OK SIGNAL WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF DIMENSION 8% 87% 89% 90.5% 90.5% 9% 5V : 5.6A/5VAC.8A/30VAC V~48V : 8.A/5VAC 3.9A/30VAC 5A/5VAC 40A/30VAC <.0mA / 40VAC 05 ~ 5% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 5.75 ~ 6.75V 3.8 ~ 6.8V 7 ~ 0.5V 7.6 ~ 3.4V 3 ~ 36.5V 56.6 ~ 66.V Protection type : Shut down o/p voltage, re-power on to recover The TTL signal out, power supply turn on = 0 ~ V ; power supply turn off = 3.3 ~ 5.6V -30 ~ +70 (Refer to "Derating Curve") 0 ~ 90% RH non-condensing -40 ~ +85, 0 ~ 95% RH ± 0.03%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL60950-, TUV EN approved I/P-O/P:3KVAC I/P-FG:KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:00M Ohms / 500VDC / 5 / 70% RH Parameter Standard Conducted Radiated Harmonic Current Voltage Flicker EN5504, EN604-3, EN Parameter ESD Radiated EFT / Burst Surge Conducted Magnetic Field Voltage Dips and Interruptions EN550 (CISPR) / EN550 (CISPR) Class B EN550 (CISPR) / EN550 (CISPR) Class B EN EN Standard EN EN EN EN EN EN EN K hrs min. Telcordia SR-33 (Bellcore) ; 09.K hrs min. MIL-HDBK-7F (5 ) Test Level / Note Test Level / Note Level 3, 8KV air ; Level, 4KV contact Level 3 Level 3 Level 4, 4KV/Line-Earth ; Level 3, KV/Line-Line Level 3 Level 4 >95% dip 0.5 periods, 30% dip 5 periods, >95% interruptions 50 periods 50*7*4mm (L*W*H) PACKING.64Kg; 6pcs/0.8Kg/.CUFT File Name:RSP-750-SPEC

3 RSP-750_ EH-07 Block Diagram I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING RECTIFIERS & PFC POWER SWITCHING O.L.P. RECTIFIERS & FILTER +S -S PFC fosc : 90KHz PWM fosc : 70KHz PFC CONTROL PWM CONTROL DETECTION CIRCUIT DC OK PV O.V.P. AUX POWER FAN RECTIFIERS CONTROL ON/OFF RECTIFIERS & FILTER AUX POWER(V/0.A) AUX GND Static Characteristics 00 INPUT MODEL 5V V 5V 90 00~64VAC 500W 00A 750W 6.5A 750W 50A (%) VAC MODEL INPUT 00~64VAC 450W 90A 4V 75.W 3.3A 675W 56.5A 7V 750.6W 7.8A 675W 45A 48V 753.6W 5.7A INPUT VOLTAGE (VAC) 60Hz 90VAC W 8.7A W 5.0A 678.4W 4.3A Derating Curve Efficiency vs Load (48V Model) (%) EFFICIENCY (%) V AMBIENT TEMPERATURE ( ) (HORIZONTAL) 70 0% 0% 30% 40% 50% 60% 70% % 90% 00% The curve above is measured at 30VAC. File Name:RSP-750-SPEC

4 RSP-750_ EH-07 Function Manual.Remote Sense The remote sensing compensates voltage drop on the load wiring up to 0.5V TB 3 +S -S PV PC S S PS PO DC_OK GND GND G-AUX V-AUX 4 PIN3 -S - + PIN +S 4 Fig. The +S signal should be connected to the positive terminal of the load whereas -S signal to the negative terminal. By factory default, on, Remote (pin3) and V-AUX (pin4), PV(pin5) and PS (pin6), and PC (pin7) and PO (pin8, respectively, are shorted when shipped. The power supply will have no output if the shorting connector is not assembled unless certain functin needs to be activated..remote The power supply can be turned ON/OFF by using the Remote function. TB S -S PV PC S S PS PO DC_OK GND GND G-AUX 3 V-AUX SW Fig. Between Remote (pin3) and V-AUX(pin4) SW close (Short) SW open (Open) Power Supply Status ON OFF When multiple power supplies need to turn ON/OFF simultaneously by Remote control, -S & on, as well as +S &, on each power supply should be connected. File Name:RSP-750-SPEC

5 RSP-750_ EH Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to 40~0% of the nominal voltage by applying EXTERNAL VOLTAGE. Nominal Vout Vout 0%(Typ.) OUTPUT VOLTAGE (%) Non-Linear UVP 0%(Typ.) EXTERNAL VOLTAGE (VDC) If EXTERNAL VOLTAGE (VDC) <0.5V,the power supply may enter under voltage protection; it needs to be restarted to work. S S PS PO 4 8 External Voltage (~5.5VDC) S -S PV PC DC_OK GND Fig 3. 3 GND G-AUX V-AUX 4 Caution: By factory default, the Output Voltage Programming is not activated, and PV (pin5) and PS(pin6) are shorted by connector. Whenever this function is not needed to activate, as assumed in other sections diagrams, please keep PV (pin5) and PS(pin6) shorted ; other wise, the power supply will have no output. 4. Constant Current Level Programming (or, PC / remote current programming / dynamic current trim) The constant current level can be trimmed to 40~0% of the rated current by applying EXTERNAL VOLTAGE. CONSTANT CURRENT LEVEL (%) Io 5%(Typ.) Rated Current Non-Linear EXTERNAL VOLTAGE (VDC) External Voltage (~5.5VDC) S -S PV PC DC_OK GND S S PS 4 6 PO Fig 4. 3 GND G-AUX V-AUX 4 Caution: By factory default, the Output Current Programming is not activated, and PC(pin7) and PO(pin8) are shorted by connector. Whenever this function is not needed to activate, as assumed in other sections diagrams, please keep PC(pin7) and PO(pin8) shorted ; otherwise, the power supply will have no output. TB File Name:RSP-750-SPEC

6 RSP-750_ EH-07 5.DC_OK signal "DC_OK" is an open collector signal. It indicates the output status of the power supply. It can operate in two ways : One is sinking current from external TTL signal ; the other is sending out a TTL voltage signal. Sinking current from external TTL signal: The maximum sink current is 0mA and the maximum external voltage is 5.6V. Sending out TTL voltage signal : Between DC- OK(pin9) and GND(pin0&) Output Status 0 ~ V 3.3 ~ 5.6V Power supply ON Power supply OFF TB 3 +S -S PV PC S S PS PO DC_OK GND GND G-AUX V-AUX Fig 5. File Name:RSP-750-SPEC

7 RSP-750_ EH-07 Mechanical Specification Case No.A Unit:mm M4 L= SVR Air flow direction 7 0 TB 3 3-M4 L= M4 L= Mounting Instruction Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque M4 M4 6mm 4mm Control Pin No. Assignment () : HRS DF-4DP-DS or equivalent 3 Mating Housing HRS DF-4DS or equivalent Terminal HRS DF-**SC or equivalent 4 7~Kgf-cm 7~Kgf-cm Mounting Surface Mounting Screw L Chassis of RSP-750 Pin No. Function Description +S Positive sensing for remote sense. 3 S -S Signal. The S should be connected to the +S to reduce the noise when "output voltage programming" function is in use. Negative sensing for remote sense. 4 S Signal. The S should be connected to the -S to reduce the noise when "output voltage programming" function is in use. 5 PV Connect to external DC voltage source for output voltage programming, referenced to pin 0, (GND) PS PC PO Reference pin regarding output voltage programming. Please refer to the Function Manual. Connect to external DC voltage source for output current programming. Reference pin regarding output current programming. Please refer to the Function Manual. 9 0, DC_OK GND G-AUX Open collector signal, referenced to pin0,(gnd). Low when PSU turns on. The maximum sink current is 0mA and the maximum external voltage is 5.6V. These pins connect to the negative terminal (). Return for DC_OK Signal output. Auxiliary voltage output ground. The signal return is isolated from the output terminals ( & ). 3 Turns the output on and off by electrical or dry contact between pin 3 ( ON/OFF) and pin 4 (V-AUX). Short: Power ON, Open: Power OFF. 4 Auxiliary voltage output, 0.8~3.V, referenced to pin (G-AUX). V-AUX The maximum load current is 0.A. This output is not controlled by the "remote ON/OFF control". File Name:RSP-750-SPEC

8 RSP-750_ EH-07 AC Input Terminal Pin No. Assignment Pin No. 3 Assignment Diagram Mx a imum mounting torque AC/N AC/L FG 8Kgf-cm DC Output Terminal Pin No. Assignment Assignment Diagram Mx a imum mounting torque, 0Kgf-cm Installation Manual Please refer to : File Name:RSP-750-SPEC

9 Headquarter Switzerland: Pewatron AG Thurgauerstrasse 66 CH-50 Zurich Phone Office Germany: Pewatron Deutschland GmbH Edisonstraße 6 D-8576 Unterschleißheim Phone info.de@pewatron.com We are here for you. Addresses and Contacts. Sales Germany & Austria Postcode Postcode Postcode Austria Kurt Stritzelberger Phone Mobile kurt.stritzelberger@pewatron.com Postcode Postcode Gerhard Vetter Phone Mobile gerhard.vetter@pewatron.com Geometrical sensors Sensor elements Thorsten Ravagni Phone thorsten.ravagni@pewatron.com Sales Switzerland & Liechtenstein Postcode Basil Frei Phone Mobile basil.frei@pewatron.com Postcode Christian Mohrenstecher Mobile christian.mohrenstecher@pewatron.com Sales International Key Accounts Peter Felder Phone Mobile peter.felder@pewatron.com Sales Other Countries / Product Management Pressure Sensors Philipp Kistler Phone philipp.kistler@pewatron.com Gas sensors / Gas sensor modules Load cells Dr. Thomas Clausen Phone thomas.clausen@pewatron.com Flow / Level / Medical products Dr. Adriano Pittarelli Phone adriano.pittarelli@pewatron.com Accelerometers / Level Flow sensor elements Thorsten Ravagni Phone thorsten.ravagni@pewatron.com Power supplies Sebastiano Leggio Phone sebastiano.leggio@pewatron.com Linear position sensors Angle sensors Eric Letsch Phone eric.letsch@pewatron.com Drive technology CH Postcode / DE Roman Homa Mobile roman.homa@pewatron.com Drive technology CH Postcode / AT / IT / FR Christian Mohrenstecher Mobile christian.mohrenstecher@pewatron.com Current sensors Power solutions Osman Coban Phone osman.coban@pewatron.com Competitive sensor & power supply solutions worldwide