FTU233. Ripple Control Receiver. Technical Data. Load Management Ripple Control

Transcription

1 Load Management Ripple Control Ripple Control Receiver FTU233 Technical Data The FTU233 combines the functionality of a ripple control receiver and a full calendar time switch. The FTU233 receiver is suited for operation as ripple control receiver with decentralized autonomy and allows for simple remote reprogramming of parameters by means of ripple control messages. The device may also be used as calendar time switch without ripple control system. Document Version: c File: FTU233 Technical Data D _c 2011 Landis+Gyr (Europe) AG D

2 2/5 FTU233 Ripple Control Receiver Technical Data Electrical Specifications Characteristics of 230V Version Supply voltage U n 230 V (+10/ 15%) Powerl frequency f n 50 Hz (±2%) Power consumption (50 Hz) 0.7 W / 7.5 VA Characteristics of 110V Version Supply voltage U n 110 V (+10/ 15%) Power frequency f n 50 Hz (±2%) Power consumption (50 Hz) 0.6 W / 4.5 VA Communication Ripple Control Signal Nominal functional voltage U f % U n Nominal control frequency f s Hz Bandwidth 0.6 6% of f s Supports Decabit,Semagyr, Ricontic ripple control signals and other pulse codes; code length, pulse length and duration are programmable. Output Relay Number / Total Current Maximum 3 I tot 50 A Transmitter outage detection (failsafe), time is programmable at any interval (15 min... 63h 45 min.) Test function with test button Event log with up to entries Backup clock (optional): Supercapacitor-buffered real time clock with 36 hours reserve power, optional plugtype battery module for 1 year reserve power without supply voltage Parameterization Parameterization with a PC operating under Windows Parameterization Software RPT01 The software is user-friendly and allows flexible programming of the receiver functions using interpreter programs. Additional conditions and priorities can be formed by up to 16 flags. 8 Flags are nonvolatile; their status is stored even during a power outage. For parameterization, a programming adapter with infrared interface according to IEC is used. The RCA208 adapter allows the FTU2x3 to be programmed without a connection to power supply. Service Software for Pocket PC. Data transfer via infrared interface Contact Rating C/O Switch cos = 1 cos = V / 25 A 250 V / 15 A Environment Temperature Operating temperature 20 to +60 C Storage temperature -30 to +70 C Receiver Functions Intelligent annual time switch with remote programming Time switch operation with holiday calendar and summer/winter time setting Frequency-dependent load shedding Reception frequency switch Time and command strings for date-specific and timespecific automatic switching operations Astronomical calendar for lighting control Learning function: Memorized switch times and automatic initiation (e.g. in case of transmitter outage) LED for operational status display Interpreter programs for random allocation of commands and addresses to the relays Up to 24 parallel program executions, including 4 with timing functions (delay, wiper, loop, etc.) Relay confirmation selectable at any intervals from 5 to 30 minutes Automatic correction of pulse distortion Signal level storage of last message Programmable response to power outages and restoration of power Enclosure Protection IEC60529 Upright installation IP 52 without negative pressure Transverse installation IP 50 Damp heat, cyclic Electromagnetic Compatibility EN Electrostatic discharge immunity IEC Air discharge 15 kv Contact discharge 8 kv Immunity to RF fields IEC Mhz to 2.7 GHz 10 and 30 V/m Electrical fast transient/ burst immunity IEC All current and voltage circuits 4 kv Surge immunity IEC All current and voltage circuits 4 kv Protection class as per IEC Class II

3 , , , /5 Emission Class EN 55022/CISPR22 B Immunity IEC Voltage dips and variations IEC Dimension Drawings Receiver with small terminal cover ( ) Insulation AC voltage IEC All current and signal paths 4 kv 50 Hz; 1 min Surge voltage IEC All current and signal paths 6 kv; 1.2/50 us Testing according to IEC General Product Standards Ripple control General requirements and tests IEC Detailed requirements on ripple control IEC Detailed requirements on time switch IEC ,8 Receiver with medium terminal cover ( ) Conformity Europe CE Connections Phase connections Conductor cross-section 0.5 mm mm 2 Relay connections Conductor cross-section c/o contact 0.5 mm mm 2 Wiring Diagram K 1 K 2 K 3 a b a b a b 55, Receiver with large terminal cover ( ) c c c Phase link for connecting L with the relay levers for K1-K3 (Order No ). Weight and Dimensions Weight Fully equipped 0.6 kg 55,

4 /5 FTU233 Installation on Meter Terminal Cover Adapter for installation on meters ZMB, ZMD...CT and ZMD...AT Adapter for spring-loaded installation of receiver DIN : 140 DIN Adapter-Verlängerung ( abnehmbar ) L&G / ERMI : Adapter-Verlängerung ( abnehmbar ) Candelabra adapter as per DIN 438 Diagram variations as per drawing D Form A Form B

5 5/5 FTU233 Accessories Components Relay 25 A, change-over contact Adapter for ZMB meters Adapter, spring-loaded, for ZMB + DIN meters Terminal cover, small Terminal cover, medium Terminal cover, large Mounting rail (2 pcs.) including screws P Phase link Programming Tools and Adapters RPT01, PC programming software RCA208, Programming head, plug-type, USB RCA112, Programming head, optical, USB 7RZR0101XXXX RCA208 RCA112 Testing Tools and Analyzer RCI100, Ripple control test transmitter RCA111, RS232-USB Converter 72-RCI100 RCA111 Copyright 2011, Landis+Gyr (Europe) AG. All rights reserved. Technical specifications subject to change. Landis+Gyr (Europe) AG Business Line Load Management Undermülistrasse Fehraltorf Switzerland Phone.: +41 (0) Service Phone 24/7: +41 (0)