AEI800L Avid extreme Liquid Cooled Inverter Module Data Sheet REV 00, March AEI800L Liquid Cooled Inverter Module Data Sheet

Transcription

1 AEI800L Avid extreme Liquid Cooled Inverter Module REV 00, March 2016 Avid Controls Inc Park 290 Drive, Waller, TX 77484, USA (+1) (281) Page 1 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

2 Contents 1. Introduction WARNINGS Specification Electrical Power Section Electrical Control & Interface Section Cooling Environmental Mechanical High Voltage / Power Connections Low Voltage / Control Connections Overview TB3 24V DC Power TB4 Analog Outputs TB5 Solid State Relays TB6 External Trip PL2 Controller Connection User Selectable Options Overview Over-volts Trip Mode Condensation Detection Trip Defeat Analog Output Mode LED s and Fault Indication Discrete LED s LED Feedback Indication Fault Codes Document Revision History Page 2 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

3 1. Introduction The AEI800L inverter module is a high reliability liquid cooled inverter module with a nominal rating of 800A and 690Vac. Its significant technical attributes are: o Sintered solder-free IGBT modules for extended life operation o Ruggedized IGBT die for improved environmental robustness o Reduced internal voltage overshoot o More robust, fully digital gate driver o Built-in condensation detection o Continuous, accurate monitoring of IGBT silicon temperature under all operating conditions It is intended as an upgraded replacement for the MVDL800 modules from GE Power Conversion, and is therefore broadly compatible with that module. Unless otherwise stated in this data sheet, all documentation related to the GE Power Conversion MV DELTA and the MV3000 drive range is applicable to the AEI800L module. This data sheet should be considered an addendum to that documentation set. For reference, a typical set of applicable GE documents is: o T1676EN, MV3000 Getting Started Manual for AC-fed Drives o T2002EN, MV3000 Getting Started Manual for Active Energy Management Drives o T1693EN, MV DELTA Liquid Cooled Drive System o T1679EN, MV3000 Drive Range Software Technical Manual 2. WARNINGS Always refer to the Cautions and Warnings in the associated MV DELTA and MV3000 manuals when installing / commissioning / fault-finding any system containing an AEI800L module. This equipment may be connected to more than one live circuit. Disconnect ALL supplies before working on the equipment. Wait at least 5 minutes after isolating supplies and check that the voltage between DC+ and DC- has reduced to a safe level before working on the equipment. Surfaces on the coolant pipes can reach high temperatures and remain hot for some time after power is removed. Ensure that all coolant has cooled to a safe temperature and the equipment is suitably drained and isolated before the external pipework is disconnected from the equipment. Page 3 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

4 3. Specification 3.1 Electrical Power Section Specification Continuous Current, 690V Renewable Energy Applications Continuous Current, 600V Pump Applications Value for AEI800L 800A 800A Notes & Applicable Conditions 60s Overload = 110% once per 10 minutes DC Link Voltage = 1100V Coolant Temp. = 60 C PWM Frequency = 1.8kHz (Generator) = 2.5kHz (Network) Generator Power Factor = Network Power Factor = 1.00 Generator & Mains Freq. > 20Hz 60s Overload = 110% once per 10 minutes DC Link Voltage = 850V Coolant Temp. = 60 C PWM Frequency = 2.5kHz Motor Power Factor = 0.85 Motor Frequency > 20Hz Continuous Current, 600V Hoist Applications Continuous DC Link Operating Voltage Short Term (7.5s) DC Link Operating Voltage Non-Operating DC Link Withstand Voltage 587A 1188 V 1262 V 1350 V DC Link Capacitance µf 60s Overload = 150% once per 10 minutes DC Link Voltage = 820V Coolant Temp. = 60 C PWM Frequency = 2.5kHz Motor Power Factor = 0.85 Motor Frequency > 1Hz Maximum PWM Frequency 2.5 khz In some circumstance, higher frequencies may be used with de-rating contact Avid Controls if this is required. Page 4 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

5 3.2 Electrical Control & Interface Section Specification Value for AEI800L Notes Controller Interface 40-Way Ribbon Connector Fully compatible with GE Power Conversion DELTA Transistor Module Control Power Source External 24 V DC Supply Does not use DELTA SMPS Module Control Power Voltage 24 V DC +/- 5 % Power on and power off transients must occur in less than 500ms and be monotonic. Control Power Current Continuous (Peak) 5A (10A) Analog Outputs Fault Indication Operational Indication 4 Channels +/-10V Fault Codes indicated on CDC for all compatible faults Two digit LED display for additional diagnostic codes Two 24V Solid-State relay outputs for indication of fault status and condensation detection Two digit LED display for display of DC link voltage, currents and temperatures Optional indication for phase currents, temperatures etc. DIP switch function selection See section 7.3 for definition of fault codes. See section 7.2 for details. DC Link Voltage Feedback Accuracy +/- 1000V DC Measured internally within inverter unit Page 5 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

6 3.3 Cooling Specification Value for AEI800L Coolant Type Minimum Coolant Flow Maximum Coolant Inlet Pressure Coolant Pressure Drop 50/50 Water/Ethylene Glycol 25 liters/min (6.6 US-GPM) 300kPa (45psi) To be determined, but not meaningfully different to DELTA module Maximum Coolant Inlet Temperature 60 C Minimum Coolant Inlet Temperature 0 C Coolant Connection Options Typical heat load to coolant (allow 33% more than quoted values when designing cooling system) 2x Quick-Disconnect at bottom of unit 2x hose-barb at bottom of unit 1x hose-barb top, and 1x hose-barb bottom 1100Vdc, 800A, PWM= 2.5kHz, PF= 1.0: 8.8kW 1100Vdc, 800A, PWM= 1.8kHz, PF= -0.89: 7.0kW 850Vdc, 800A, PWM=2.5kHz, PF= 0.92: 7.1kW 976Vdc, 800A, PWM=1.25kHz, PF=0.90: 5.5kW 3.4 Environmental Specification Ambient Temperature (Internal cabinet temperature) Humidity Value for AEI800L 0 to 50 C 5% to 95% RH Unit must not be operated in the presence of condensation. Page 6 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

7 3.5 Mechanical Specification Dimensions Mass Electrical Connections Mounting Value for AEI800L 248mm W x 1232mm H x 546mm D) (9.75 W x 48.5 H x 21.5 D) 105kg (231lb) Location and type compatible with MVDL800 Module Fully compatible with MVDL800 Module Page 7 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

8 4. High Voltage / Power Connections AEI800L Liquid Cooled Inverter Module All power connections are compatible with the GE 800A DELTA module: Connection AC Power Terminals DC Power Terminals Ground Connection Auxiliary Power Supply Connection Value for AEI800L 2 x M10 studs per phase Maximum cable size per stud is120mm 2 2 x M10 studs each for DC+ and DC- Maximum cable size per stud is120mm 2 1 x M10 bolt 2-way connector TB1 for optional auxiliary SMPS 5. Low Voltage / Control Connections 5.1 Overview All control connections are made to terminals and plugs on the Controller Interface Board (C.I.B.) as shown in the following image (left hand side is towards the top of the unit when installed): V The terminal blocks may not be physically numbered pin one is always towards the top of the unit when installed. Page 8 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

9 5.2 TB3 24V DC Power Terminals Function Specifications and Notes 1, 2 3, 4 24V SUPPLY [+] 24V SUPPLY [-] 24V DC Supply, +/-5%, 10A maximum load Recommended to use two terminals each for supply and ground to minimize volt drop [-] terminals are connected to system 0V [GROUND] on the C.I.B. 5.3 TB4 Analog Outputs Terminals Function Specifications and Notes 1, 2, 3, 4 ANALOG OUTPUT A, B, C, D 5 0V (GND) Analog outputs for user diagnostic monitoring See section 6.4 for details on selecting specific signals to be output via analog outputs. Range is +/-10V Maximum load current is 5mA Output source impedance is 100Ω Maximum error at all outputs is +/- 1% of full range with zero load Page 9 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

10 5.4 TB5 Solid State Relays Terminals Function Specifications and Notes 1, 2 SS RELAY A 3, 4 SS RELAY B Inverter module fault indication Relay energized indicates no fault condition Relay de-energized indicates a fault condition Condensation detection indication Relay energized indicates that condensation is NOT detected in the unit Relay de-energized indicates that condensation IS detected in the unit This is provided so that external system control logic may de-energize the whole drive system when condensation is detected. Maximum operating voltage is 60Vdc / 40Vac(rms) Maximum load current is 0.4A Typical ON resistance is 0.5 Ω NOT overload (short-circuit) or overvoltage protected For reference, on-board device is Panasonic AVQ202A solid-state relay. 5.5 TB6 External Trip Terminals Function Specifications and Notes 1 EXT TRIP SUPPLY 2 EXT TRIP IN Connected to +24V SUPPLY via 150Ω resistor Connect to EXT TRIP IN to allow unit to run > +12V is healthy input < +7V causes the unit to trip on EXTERNAL TRIP fault Typically connected to EXT TRIP SUPPLY (as unit shipped) 5.6 PL2 Controller Connection Standard 40-way ribbon cable header Connected to CDC Controller PL2 to PL7 (depending on system configuration) Identical to 40-way ribbon header for controller interface on the GE Delta module Connection to CDC must be segregated, shielded and bonded in the same manner as the GE DELTA Module Page 10 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

11 6. User Selectable Options AEI800L Liquid Cooled Inverter Module 6.1 Overview There are a number of options for the inverter unit that must be configured. These are configured using a set of 8 DIP switches on the Controller Interface Board. These switches are numbered from 1 to 8, the ON position is towards the PCB itself, and the OFF position is towards the edge of the board. The DIP switches are very small, so a fine point instrument (and decent eyesight) is needed to set them correctly. The unit is shipped with all DIP switches in the OFF position. 6.2 Over-volts Trip Mode On the GE Delta, the DC link over-volts trip mode is configured on the switch-mode power supply (SMPS) unit. For the Avid module, this configuration is done on the inverter module itself, using DIP switches 1-4. The following table defines the operation of these switches: SWITCH SETTINGS SW 1 SW 2 SW 3 SW 4 DC Link Voltage Trip Instant DC Link Voltage Trip Delayed Delay Time Notes OFF OFF OFF OFF 1188 Vdc None N/A OFF OFF OFF ON 0.5s OFF OFF ON OFF 1.0s OFF OFF ON ON 1.5s OFF ON OFF OFF 2.0s OFF ON OFF ON 2.5s OFF ON ON OFF 3.0s OFF ON ON ON 3.5s 1262 Vdc 1188 Vdc ON OFF OFF OFF 4.0s ON OFF OFF ON 4.5s ON OFF ON OFF 5.0s ON OFF ON ON 5.5s ON ON OFF OFF 6.0s ON ON OFF ON 6.5s ON ON ON OFF 7.5s ON ON ON ON 1290 Vdc None N/A Equivalent behavior of GE MVC and MVC SMPS modules Equivalent behavior of GE MVC SMPS Module Units configured in one of these modes are used in the Delta 1 position of the MV3000 system. Equivalent behavior to GE MVC SMPS module. This mode is used in the Delta 2 to 6 position of the MV3000 system Page 11 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

12 6.3 Condensation Detection Trip Defeat SW5 sets the action taken when the internal condensation detector is active: OFF: Condensation detection is signaled via SS Relay B. Additionally, the unit will trip the drive system when condensation is detected. ON: Condensation detection is signaled via SS Relay B, but unit does not trip. This mode is provided to minimize nuisance tripping but with an increased risk of operation in the presence of damaging condensation. 6.4 Analog Output Mode The unit provides four analog outputs for system monitoring / debugging. See section 5.3 for electrical specifications. Scaling of different signal types is as follows: Signal Type Current DC Link Voltage Temperature Condensation Scaling +/- 10 V output is equivalent to +/- 2500A Positive values are defined as positive current OUT of the AC terminals of the unit. When the output mode is rectified phase currents, only positive values will be output. The formula for rectified mode is: Output = MAXIMUM ( Ia, Ib, Ic ). 0 to +10V is equivalent to 0 to 1500 Vdc 0 to +10V is equivalent to 0 to 150 C Note that due to the nature of the internal temperature sensor, any temperature below 30 C will be indicated as 30 C. 0V indicates no moisture detected. +5V indicates the moisture detection is at the trip level. +10V indicates double the trip level. Page 12 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

13 The signals that are output are controlled by DIP switches 6 & 7: Switch Positions Mode Analog Channel Outputs SW7 SW6 A B C D OFF OFF MIXED Full wave rectified AC currents Maximum IGBT module temperature Minimum IGBT module temperature OFF ON CURRENTS A phase AC current B phase AC current C phase AC current ON OFF TEMPS. ON ON LOG A phase IGBT module temperature Full wave rectified AC currents B phase IGBT module temperature Maximum IGBT module temperature C phase IGBT module temperature Condensation detector signal DC Link Voltage 7. LED s and Fault Indication The unit has two discrete LED s (red and green) and a two digit LED display. The discrete LED s indicate the operational state of the unit and the numeric display may either indicate various feedback signals or all active faults. 7.1 Discrete LED s - OFF - ON - FLASHING RED LED GREEN LED Meaning 24V supply is not present Internal error present on Controller Interface Board or 24V supply is out of tolerance Unit healthy (not tripped) and disabled (IGBT s not switching) Unit healthy (not tripped) and enabled (IGBT s switching) Unit faulted. Fault codes will be displayed on 2-digit display, appropriate fault codes sent to CDC (as supported see section7.3) CDC is attempting a reset cycle Page 13 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

14 7.2 LED Feedback Indication When the unit is not faulted, the 2-digit LED display cycles through indications of a number of operational feedbacks. Each feedback is displayed for 1s, before the display cycles to the next feedback. A "--" pattern is used to indicate the start of the cycle. The cycle is: "--" CURRENT - A PHASE CURRENT - B PHASE CURRENT - C PHASE TEMPERATURE A PHASE TEMPERATURE B PHASE TEMPERATURE C PHASE DC LINK VOLTAGE In a similar manner to the analog outputs, each value is displayed as the percentage of a defined value: Signal Type Explanation & Scaling Current DC Link Voltage Temperature 100% output is equivalent to 2500A The formula for the indication is: o % CURRENT = 100% x AVERAGE 1s ( Phase Current ) / 2500A Or, in words, the formula is the absolute current averaged over 1s, expressed as a percentage of 2500A Average over 1s expressed as percentage of 1500 Vdc Expressed as percentage of 150 C (0 C = 0%, 150 C = 100%) Note that due to the nature of the internal temperature sensor, any temperature below 30 C will be indicated as 20%. Page 14 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

15 7.3 Fault Codes When the unit has a fault, the 2-digit LED display cycles through a list of all active faults. Each fault that the unit recognizes is encoded into a compatible fault code for indication by the CDC. The Avid unit can identify many more and different faults than the CDC is able to recognize, so some rationalization has been necessary. The following table describes each fault code on the unit, together with the fault code that is transmitted to the CDC for each of the faults recognized by the Controller Interface Board: Fault Code on LED Display Meaning Trip Code Transmitted to CDC *1 See MV3000 Software Technical Manual for Details 1 A Phase IGBT Self-Protect Fault 31 2 B Phase IGBT Self-Protect Fault 33 3 C Phase IGBT Self-Protect Fault 35 4 A Phase Heatsink Over Temperature Fault 32 5 B Phase Heatsink Over Temperature Fault 34 6 C Phase Heatsink Over Temperature Fault 36 7 A Phase Silicon Over Temperature Fault 32 8 B Phase Silicon Over Temperature Fault 34 9 C Phase Silicon Over Temperature Fault Over Voltage (DC Link) External Trip Fault Internal Fan 1 Failure (on units where this fan is fitted) Internal Fan 2 Failure (on units where this fan is fitted) Internal Fan 3 Failure (on units where this fan is fitted) Internal Fan 4 Failure (on units where this fan is fitted) Internal Fault * Internal Fault * Internal Fault * Internal Fault * Internal Fault * Internal Fault *2 247 Page 15 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00

16 Fault Code on LED Display Meaning Trip Code Transmitted to CDC *1 See MV3000 Software Technical Manual for Details 22 Internal Fault * Internal Fault * Internal Fault * Internal Fault * Internal Fault * A Phase Positive Instantaneous Overcurrent A Phase Negative Instantaneous Overcurrent B Phase Positive Instantaneous Overcurrent B Phase Negative Instantaneous Overcurrent C Phase Positive Instantaneous Overcurrent C Phase Negative Instantaneous Overcurrent Condensation Detected Internal Fault *2 212 *1: The fault code for a unit connected in the Delta 1 position of the MV3000 system is given. For units in other positions the equivalent fault code will be displayed by the CDC. See the MV3000 documentation for details. *2: These faults indicate a fault within the MV3000 system. They do not occur in normal operation and user fault-finding is generally not possible. In the unlikely event that these faults are experienced, contact Avid Controls for support. 8. Document Revision History Rev. Date Author Changes 00 3/14/2016 Gary Pace Document created Page 16 of 16 Copyright 2016 Avid Controls Inc. DTS-MID0012-REV_00