Dual SPDT CMOS Analog Switch

Size: px
Start display at page:

Download "Dual SPDT CMOS Analog Switch"

Transcription

1 Dual SPDT CMOS nalog Switch HI-5051/883 This CMOS analog switch offers low resistance switching performance for analog voltages up to the supply rails and for signal currents up to 70m. ON resistance is low and stays reasonably constant over the full range of operating signal voltage and current. R ON remains exceptionally constant for input voltages between +5V and -5V and currents up to 50m. Switch impedance also changes very little over temperature, particularly between 0 C and +75 C. R ON is nominally 25Ω. The HI-5051/883 provides break-before-make switching and is TTL and CMOS compatible for maximum application versatility. Performance is further enhanced by Dielectric Isolation processing which insures latch-free operation with very low input and output leakage currents (0.8n at +25 C). The HI-5051/883 switch also features very low power operation (1.5mW at +25 C). The HI-5051/883 is available in a 20 Ld CLCC package and operates over the -55 C to +125 C temperature range. Features This Circuit is Processed in ccordance to MIL-STD-883 and is Fully Conformant Under the Provisions of Paragraph Wide nalog Signal Range ±15V Low ON Resistance Ω (Typ), 50Ω (Max) High Current Capability m (Max) Break-Before-Make Switching - Turn-On Time ns (Typ), 800ns (Max) - Turn-Off Time ns (Typ), 400ns (Max) No Latch-Up Input MOS Gates are Protected from Electrostatic Discharge DTL, TTL, CMOS, PMOS Compatible pplications High Frequency Switching Sample and Hold Digital Filters Operational mplifier Gain Switching Pin Configuration D 3 S3 NC S 4 D HI-5051/ LD CLCC TOP VIEW LOGIC 0 PUT NC D 1 NC S V R NC V L V+ Functional Diagram S 1 S S 2 S LOGIC 1 PUT 9 5 V L V R 12 V D 1 D 3 D 2 D 4 NOTE: NC D 2 NC S 2 2 Unused pins may be internally connected. Ground all unused pins. TYPICL SWITCH S Ordering Information N P PRT NUMBER PRT MRKG TEMP. RNGE ( C) PCKGE PKG. DWG. # HI4-5051/883 HI to Ld CLCC J20. NOTE: Source and Drain are arbitrarily depicted as nalog Input and Output, respectively. They may be interchanged without affecting performance. D FN CUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures TERSIL or Copyright Intersil mericas Inc. 1989, ll Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. ll other trademarks mentioned are the property of their respective owners.

2 bsolute Maximum Ratings Voltage Between V+ and Terminals V ±V SUPPLY to Ground (V+, ) ±18V V R to Ground V SUPPLY V L to Ground V SUPPLY Digital and nalog Input Voltage (V, V S, V D ) V SUPPLY +4V -V SUPPLY -4V Peak Current (Source to Drain) (Pulse at 1ms, 10% Duty Cycle Max) m Continuous Current (ny Pin) m ESD Rating <2000V Thermal Information Thermal Resistance θ J ( C/W) θ JC ( C/W) CLCC Package O 20 Package Power Dissipation at +75 C CLCC Package W Package Power Dissipation Derating Factor above +75 C CLCC Package mW/ C Junction Temperature C Storage Temperature Range C to +150 C Lead Temperature (Soldering 10s) C Recommended Operating Conditions Operating Temperature Range C to +125 C Operating Supply Voltage ±15V Logic Supply Voltage (V L ) V Logic Reference Voltage (V R ) V nalog Input Voltage (V S ) ±V SUPPLY ddress Low Level (V L ) V to 0.8V ddress High Level (V H ) V to +5.0V CUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. TBLE 1. D.C. ELECTRICL PERFORMNCE SPECIFICTIONS Device Tested at: Supply Voltage = ±15V, V L = +5.0V, V R = 0.0V, V H = 2.4V, V L = +0.8V, unused pins are grounded, unless otherwise specified. D.C. PRMETERS SYMBOL CONDITIONS Switch ON Resistance R DS2 V D = -10V, I S = 10m Source OFF Leakage Current Drain OFF Leakage Current Channel ON Leakage Current I S(OFF) I D(OFF) I D(ON) V D = 10V, I S = -10m V S = -10V, V D = 10V V S = 10V, V D = -10V V D = -10V, V S = 10V V D = 10V, V S = -10V V D = V S = 10V V D = V S = -10V GROUP SUBGROUPS TEMPERTURE ( C) M MX UNITS Ω 2, 3-55 to Ω Ω 2, 3-55 to Ω n 2, 3-55 to n n 2, 3-55 to n n 2, 3-55 to n n 2, 3-55 to n n 2, 3-55 to n n 2, 3-55 to n Low Level ddress Current I L V = 0V µ 1, 2 2, 3-55 to µ High Level ddress Current I H V = 2.4V, 5V µ 1, 2 2, 3-55 to µ Positive Supply Current +I CC V = 0V, 5V µ 1, 2 2, 3-55 to µ Negative Supply Current -I CC V = 0V, 5V µ 1, 2 2, 3-55 to µ 2 FN8289.0

3 TBLE 1. D.C. ELECTRICL PERFORMNCE SPECIFICTIONS (Continued) Device Tested at: Supply Voltage = ±15V, V L = +5.0V, V R = 0.0V, V H = 2.4V, V L = +0.8V, unused pins are grounded, unless otherwise specified. D.C. PRMETERS SYMBOL CONDITIONS GROUP SUBGROUPS TEMPERTURE ( C) M MX UNITS Logic Supply Current +I L V = 0V, 5V µ 2, 3-55 to µ Reference Supply Current +I R V = 0V, 5V µ 2, 3-55 to µ TBLE 2..C. ELECTRICL PERFORMNCE SPECIFICTIONS Device Tested at: Supply Voltage = ±15V, V L = +5.0V, V R = 0.0V, V H = +5.0V, V L = +0.0V, unused pins are grounded, unless otherwise specified. PRMETERS SYMBOL CONDITIONS Turn ON Time t ON V S = 10V, -10V C L = 10pF R L = 1kΩ Turn OFF Time t OFF V S = 10V, -10V C L = 10pF R L = 1kΩ GROUP SUBGROUPS TEMPERTURE ( C) M MX UNITS ns ns ns ns ns ns TBLE 3. ELECTRICL PERFORMNCE SPECIFICTIONS (NOTE 1) Device Characterized at: Supply Voltage = ±15V, V L = +5.0V, V R = 0.0V, V H = 4.0V, V L = 0.8V, unused pins are grounded, unless otherwise specified. PRMETERS SYMBOL CONDITIONS NOTE ON Resistance Match (Channel to Channel) R ON2 Match V D = ±10V I D = 10m TEMPERTURE ( C) M MX UNITS Ω ddress Capacitance C V = 0V, 5V pf Switch Input Capacitance C S(OFF) Switch Off: V = 0V pf Switch Output Capacitance C D(OFF) Switch Off: V = 0V pf C D(ON) Switch On: V = 5V pf Drain to Source Capacitance C DS(OFF) Switch Off: V = 0V pf Off Isolation V ISO V S = 2V f = 100kHz, R L =100Ω db Crosstalk V CT V S = 2V f = 100kHz, R L =100Ω Charge Transfer Error V CTE V S = GND, C L = 0.01µF V = 0V to f = 200kHz db mv NOTE: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. TBLE 4. ELECTRICL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (See Tables 1 and 2) Interim Electrical Parameters (Pre Burn-in) 1 Final Electrical Test Parameters 1 (Note 2), 2, 3, 9, 10, 11 Group Test Requirements 1, 2, 3, 9, 10, 11 Groups C & D Endpoints 1 NOTE: 2. PD applies to Subgroup 1 only. 3 FN8289.0

4 Test Circuits 10m V 2 R ON = 10m V 2 I S(OFF) I D(OFF) ±10V ±10V ±10V FIGURE 1. R DS FIGURE 2. I S(OFF) I S(OFF) I D(OFF) I D(ON) ±10V ±10V ±10V FIGURE 3. I D(OFF) FIGURE 4. I D(ON) +V CC +I CC +V CC V GND -I CC V I -V CC GND -V CC FIGURE 5. DDRESS CURRENT FIGURE 6. SUPPLY CURRENTS 4 FN8289.0

5 Test Circuits (Continued) V 2V P-P 50Ω R L V V 2V P-P SWITCHED CHNNEL 50Ω V R L OFF ISOLTION 20 Log V = V FIGURE 7. OFF ISOLTION R L CROSSTLK 20 Log V = V NOTE: pplies only to dual or double throw switches. FIGURE 8. CROSSTLK S D 0.01MF TO MESUREMENT CIRCUITRY WITH PUT RESISTNCE OF 1MΩ OR GRETER DRIVER f = 200kHz SQURE WVE t R 20ns IF PULSE TEST IS USED: t R, t F 20ns V (DRIVER) V CTE NOTE: V CTE may be a positive or negative value. SWITCHG TRNSIENT DROOP CUSED BY DEVICE LEKGE ND MESUREMENT CIRCUITRY FIGURE 9. CHRGE TRNSFER Test Characteristics V H V L V 90% 90% +10V 1 2 t ON t OFF 90% 90% 1 2 1k 1k V t OFF t ON FIGURE 10. ON/OFF SWITCH TIME (t ON, t OFF ) 5 FN8289.0

6 Test Characteristics (Continued) t 360 ON 300 t OFF DIGITL HIGH (V H ) FIGURE 11. SWITCHG TIMES FOR DIGITL TRNSITION t ON t OFF DIGITL LOW (V L ) FIGURE 12. SWITCHG TIMES FOR NEGTIVE DIGITL TRNSITION Test Waveforms 5V 5V PUT PUT PUT PUT 5V 100ns 5V 100ns Vertical Scale: Input = 5V/Div, (TTL; V H = 5V, V L = 0V) Output = 5V/Div Horizontal Scale: 100ns/Div FIGURE 13. Vertical Scale: Input = 5V/Div, (CMOS; V H = 10V, V L = 0V) Output = 5V/Div Horizontal Scale: 100ns/Div FIGURE FN8289.0

7 Burn-In Circuit HI-5051/883 CERMIC LCC NOTES: R 1 thru R 4 = 10kΩ, ±5%, 1/4W (Min) C 1, C 2, C 3 = 0.01µF/Socket (Min) or 0.1µF/Row, (Min) D 1, D 2, D 3 = 1N4002 or Equivalent/Board V L = 5.5V ±0.5V 2 = 2 = 5.5V ±0.5V (V+) - () = 30V 7 FN8289.0

8 Schematic Diagrams V+ V+ R3 VR 1 ( 2 ) TO (V R ) V+ N1 P2 N3 N2 P1 NOTE: Connect V+ to V L for minimizing power consumption when driving from CMOS circuits. FIGURE 15. TTL/CMOS REFERENCE CIRCUIT 1 ( 2 ) FIGURE 16. SWITCH CELL P3 V+ R4 200Ω V+ D1 D2 P1 N1 V R ' V L ' P4 P5 P6 P7 P8 P9 P10 P11 P P2 N2 N4 N5 N6 N7 N8 N9 N10 N11 N12 N3 NOTE: ll N-Channel bodies to, all P-Channel bodies to V+ except as shown. DIGITL PUT BUFFER ND LEVEL SHIFTER 8 FN8289.0

9 Die Characteristics DIE DIMENSIONS: 96mils x 81mils x 20mils (2430µm x 2050µm x 508µm) METLLIZTION: Type: luminum Thickness: 16kÅ ±2kÅ GLSSIVTION: Type: Nitride over Silox Silox Thickness: 12kÅ ±2kÅ Nitride Thickness: 3.5kÅ ±1kÅ SUBSTRTE POTENTIL (Powered-up): DEVICE COUNT: 82 WORST CSE CURRENT DENSITY: 1.0 x 10 5 /cm 2 at 20m Metallization Mask Layout HI-5051/883 D 1 S 1 1 D 3 S 3 V R V L S 4 D 4 V+ 10 D 2 S FN8289.0

10 Design Information The information contained in this section has been developed through characterization and is for use as application and design information only. No guarantee is implied. Typical Performance Curves T = +25 C, V SUPPLY = ±15V 80 ON RESISTNCE (Ω) V+ = +10V = -10V V+ = +12V = -12V V+ = +15V = -15V NORMLIZED ON RESISTNCE (REFERRED TO +25 C) V = 0V NLOG SIGNL LEVEL (V) FIGURE 17. ON RESISTNCE vs NLOG SIGNL LEVEL ND POWER SUPPLY VOLTGE TEMPERTURE ( C) FIGURE 18. NORMLIZED ON RESISTNCE vs TEMPERTURE n NORMLIZED ON RESISTNCE (REFERRED TO 1m) LEKGE CURRENT 10n 1n 100p I S(OFF) = I D(OFF) I D(ON) NLOG CURRENT (m) FIGURE 19. NORMLIZED ON RESISTNCE vs NLOG CURRENT 10p TEMPERTURE ( C) FIGURE 20. ON/OFF LEKGE CURRENTS vs TEMPERTURE OFF ISOLTION (db) R L = 100Ω R L = 10kΩ CROSSTLK (db) R L = 10kΩ R L = 1kΩ R L = 100Ω k 10k 100k 1M FREQUENCY (Hz) FIGURE 21. OFF ISOLTION vs FREQUENCY k 10k 100k 1M FREQUENCY (Hz) FIGURE 22. CROSSTLK vs FREQUENCY 10 FN8289.0

11 Design Information The information contained in this section has been developed through characterization and is for use as application and design information only. No guarantee is implied. Typical Performance Curves T = +25 C, V SUPPLY = ±15V (Continued) 200 POWER CONSUMPTION (mw) k 10k 100k 1M TOGGLE FREQUENCY (50% DUTY CYCLE) (Hz) FIGURE 23. POWER CONSUMPTION vs FREQUENCY For additional products, see Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. ccordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see 11 FN8289.0

12 Ceramic Leadless Chip Carrier Packages (CLCC) HI-5051/883 j x 45 o S E H S D D3 J20. MIL-STD-1835 CQCC1-N20 (C-2) 20 PD CERMIC LEDLESS CHIP CRRIER PCKGE CHES MILLIMETERS SYMBOL M MX M MX NOTES , B B , 4 B E3 E B REF 1.83 REF - B D D BSC 5.08 BSC - D BSC 2.54 BSC - h x 45 o D S E F S E PLNE 2 E BSC 5.08 BSC - E BSC 2.54 BSC - E E- PLNE 1 e BSC 1.27 BSC - e h REF 1.02 REF 5 j REF 0.51 REF M E F S HS L L B1 -H- e L3 L L L ND NE N E1 -F- E2 e1 L2 D1 B2 D2 B3 L1 Rev. 0 5/18/94 NOTES: 1. Metallized castellations shall be connected to plane 1 terminals and extend toward plane 2 across at least two layers of ceramic or completely across all of the ceramic layers to make electrical connection with the optional plane 2 terminals. 2. Unless otherwise specified, a minimum clearance of inch (0.38mm) shall be maintained between all metallized features (e.g., lid, castellations, terminals, thermal pads, etc.) 3. Symbol N is the maximum number of terminals. Symbols ND and NE are the number of terminals along the sides of length D and E, respectively. 4. The required plane 1 terminals and optional plane 2 terminals (if used) shall be electrically connected. 5. The corner shape (square, notch, radius, etc.) may vary at the manufacturer s option, from that shown on the drawing. 6. Chip carriers shall be constructed of a minimum of two ceramic layers. 7. Dimension controls the overall package thickness. The maximum dimension is package height before being solder dipped. 8. Dimensioning and tolerancing per NSI Y14.5M Controlling dimension: CH. 12 FN8289.0

HI-201HS. Features. High Speed, Quad SPST, CMOS Analog Switch. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) FN3123.

HI-201HS. Features. High Speed, Quad SPST, CMOS Analog Switch. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) FN3123. HI-HS Data Sheet September 4 FN.4 High Speed, Quad SPST, CMOS Analog Switch The HI-HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit

More information

HI-200, HI-201. Dual/Quad SPST, CMOS Analog Switches. Features. Applications. Ordering Information. Functional Diagram FN3121.8

HI-200, HI-201. Dual/Quad SPST, CMOS Analog Switches. Features. Applications. Ordering Information. Functional Diagram FN3121.8 HI-200, HI-201 Data Sheet FN3121.8 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds

More information

DATASHEET HI-201HS. Features. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) High Speed, Quad SPST, CMOS Analog Switch

DATASHEET HI-201HS. Features. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) High Speed, Quad SPST, CMOS Analog Switch DATASHEET HI-21HS High Speed, Quad SPST, CMOS Analog Switch The HI-21HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit consists of

More information

DATASHEET HI-200, HI-201. Features. Applications. Ordering Information. Functional Diagram. Dual/Quad SPST, CMOS Analog Switches

DATASHEET HI-200, HI-201. Features. Applications. Ordering Information. Functional Diagram. Dual/Quad SPST, CMOS Analog Switches DATASHEET HI-200, HI-201 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200

More information

DATASHEET. Features. Applications. Pin Configuration. Ordering Information HI-201/883. Quad SPST CMOS Analog Switch. FN7990 Rev.0.

DATASHEET. Features. Applications. Pin Configuration. Ordering Information HI-201/883. Quad SPST CMOS Analog Switch. FN7990 Rev.0. ATAHEET Quad PT CMO Analog witch The is a monolithic device comprised of four independently selectable PT switchers which feature fast switching speeds (185ns typical) combined with low power dissipation

More information

DATASHEET HI-200/883. Features. Applications. Functional Diagram. Ordering Information. Pinout. Dual SPST CMOS Analog Switch

DATASHEET HI-200/883. Features. Applications. Functional Diagram. Ordering Information. Pinout. Dual SPST CMOS Analog Switch Dual PT CMO Analog witch NOT RECOMMENDED FOR NEW DEIGN NO RECOMMENDED REPLACEMENT contact our Technical upport Center at 1-888-INTERIL or www.intersil.com/tsc DATAHEET FN6059 Rev 2.00 The HI-200/883 is

More information

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5

HA Features. Quad, 3.5MHz, Operational Amplifier. Applications. Pinout. Ordering Information. Data Sheet July 2004 FN2922.5 HA-4741 Data Sheet July 24 FN2922. Quad, 3.MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational

More information

DATASHEET HI-1818A. Features. Applications. Ordering Information. Pinout. Low Resistance, Single 8-Channel, CMOS Analog Multiplexer

DATASHEET HI-1818A. Features. Applications. Ordering Information. Pinout. Low Resistance, Single 8-Channel, CMOS Analog Multiplexer NOT RECOMMDED FOR NEW DESIGNS NO RECOMMDED REPLACEMT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Low Resistance, Single 8-Channel, CMOS Analog Multiplexer DATASHEET FN3141

More information

HI-201HS. High Speed Quad SPST CMOS Analog Switch

HI-201HS. High Speed Quad SPST CMOS Analog Switch SEMICONDUCTOR HI-HS December 99 Features Fast Switching Times, N = ns, FF = ns Low ON Resistance of Ω Pin Compatible with Standard HI- Wide Analog Voltage Range (±V Supplies) of ±V Low Charge Injection

More information

HA Features. 12MHz, High Input Impedance, Operational Amplifier. Applications. Pinout. Part Number Information. Data Sheet May 2003 FN2893.

HA Features. 12MHz, High Input Impedance, Operational Amplifier. Applications. Pinout. Part Number Information. Data Sheet May 2003 FN2893. OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 HA-2515 Data Sheet May 23 FN2893.5 12MHz, High Input Impedance, Operational Amplifier HA-2515 is a high performance operational amplifier which sets

More information

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts

HA-2640, HA Features. 4MHz, High Supply Voltage Operational Amplifiers. Applications. Ordering Information. Pinouts HA-264, HA-2645 Data Sheet January 3, 26 FN294.5 4MHz, High Supply Voltage Operational Amplifiers HA-264 and HA-2645 are monolithic operational amplifiers which are designed to deliver unprecedented dynamic

More information

DATASHEET HI-524. Features. Applications. Functional Diagram. Ordering Information. Pinout. 4-Channel Wideband and Video Multiplexer

DATASHEET HI-524. Features. Applications. Functional Diagram. Ordering Information. Pinout. 4-Channel Wideband and Video Multiplexer DATASHEET HI-524 4-Channel Wideband and Video Multiplexer The HI-524 is a 4-Channel CMOS analog multiplexer designed to process single-ended signals with bandwidths up to 10MHz. The chip includes a 1 of

More information

HA Features. 650ns Precision Sample and Hold Amplifier. Applications. Functional Diagram. Ordering Information. Pinout

HA Features. 650ns Precision Sample and Hold Amplifier. Applications. Functional Diagram. Ordering Information. Pinout HA-50 Data Sheet June 200 FN2858.5 650ns Precision Sample and Hold Amplifier The HA-50 is a very fast sample and hold amplifier designed primarily for use with high speed A/D converters. It utilizes the

More information

HA-2602/883. Wideband, High Impedance Operational Amplifier. Description. Features. Applications. Part Number Information. Pinout.

HA-2602/883. Wideband, High Impedance Operational Amplifier. Description. Features. Applications. Part Number Information. Pinout. October 2004 OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Wideband, High Impedance Operational Amplifier Features This Circuit

More information

DATASHEET HA-5101/883. Features. Applications. Ordering Information. Pinouts. Low Noise, High Performance Operational Amplifier

DATASHEET HA-5101/883. Features. Applications. Ordering Information. Pinouts. Low Noise, High Performance Operational Amplifier DATASHEET HA-511/883 Low Noise, High Performance Operational Amplifier The HA-511/883 is a dielectrically isolated operational amplifier featuring low noise and high performance. This amplifier has an

More information

DATASHEET HA-5137A. Features. Applications. Ordering Information. Pinout. 63MHz, Ultra-Low Noise Precision Operational Amplifier

DATASHEET HA-5137A. Features. Applications. Ordering Information. Pinout. 63MHz, Ultra-Low Noise Precision Operational Amplifier DATASHEET HA-5137A 3MHz, Ultra-Low Noise Precision Operational Amplifier The HA-5137 operational amplifier features an unparalleled combination of precision DC and wideband high speed characteristics.

More information

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8.

DATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8. DATASHEET HA-4741 Quad, 3.5MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each

More information

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8 HA-533 Data Sheet February 6, 26 FN2924.8 25MHz Video Buffer The HA-533 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 25MHz and

More information

DATASHEET HA-5127/883. Features. Applications. Ordering Information. Pinout. Ultra Low Noise, Precision Operational Amplifier

DATASHEET HA-5127/883. Features. Applications. Ordering Information. Pinout. Ultra Low Noise, Precision Operational Amplifier Ultra Low Noise, Precision Operational Amplifier NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc DATASHEET FN3751

More information

DATASHEET HA Features. Applications. Ordering Information. Pinout. 400MHz, Fast Settling Operational Amplifier. FN2897 Rev.5.

DATASHEET HA Features. Applications. Ordering Information. Pinout. 400MHz, Fast Settling Operational Amplifier. FN2897 Rev.5. DATASHEET MHz, Fast Settling Operational Amplifier The Intersil is a wideband, very high slew rate, monolithic operational amplifier featuring superior speed and bandwidth characteristics. Bipolar construction

More information

DATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier

DATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier 12MHz, High Input Impedance, Operational Amplifier OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 DATASHEET FN289 Rev 6. HA-255 is an operational amplifier whose design is optimized to deliver excellent

More information

DATASHEET. Features. Applications. Pin Configuration HA-5147 (CERDIP) TOP VIEW. Ordering Information HA-5147

DATASHEET. Features. Applications. Pin Configuration HA-5147 (CERDIP) TOP VIEW. Ordering Information HA-5147 DATASHEET HA-517 12MHz, Ultra-Low Noise Precision Operational Amplifiers FN291 Rev 1. The HA-517 operational amplifier features an unparalleled combination of precision DC and wideband high speed characteristics.

More information

HA MHz, Fast Settling Operational Amplifier. Features. Applications. Pinout. Part Number Information. Data Sheet November 19, 2004 FN2914.

HA MHz, Fast Settling Operational Amplifier. Features. Applications. Pinout. Part Number Information. Data Sheet November 19, 2004 FN2914. OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 888TERSIL or www.intersil.com/tsc HA595 Data Sheet November 9, 2 FN29.6 5MHz, Fast Settling Operational Amplifier The

More information

HA, HA Absolute Maximum Ratings Supply Voltage Between V+ and V Terminals V Differential Input Voltage V

HA, HA Absolute Maximum Ratings Supply Voltage Between V+ and V Terminals V Differential Input Voltage V HA, HA Data Sheet October 6, FN9.9 Dual and Quad, 8MHz, Low Noise Operational Amplifiers Low noise and high performance are key words describing HA and HA. These general purpose amplifiers offer an array

More information

DATASHEET HA-4741/883. Features. Description. Applications. Ordering Information. Pinouts. Quad Operational Amplifier. FN3704 Rev 0.

DATASHEET HA-4741/883. Features. Description. Applications. Ordering Information. Pinouts. Quad Operational Amplifier. FN3704 Rev 0. DATASHEET HA4741/883 Quad Operational Amplifier Features This Circuit is Processed in Accordance to MILSTD 883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. Slew Rate...........................0.9V/

More information

HA Features. 400MHz, Fast Settling Operational Amplifier. Applications. Ordering Information. Pinout. Data Sheet August 2002 FN2897.

HA Features. 400MHz, Fast Settling Operational Amplifier. Applications. Ordering Information. Pinout. Data Sheet August 2002 FN2897. HA-5 Data Sheet August FN97. MHz, Fast Settling Operational Amplifier The Intersil HA-5 is a wideband, very high slew rate, monolithic operational amplifier featuring superior speed and bandwidth characteristics.

More information

ISL Features. Multi-Channel Buffers Plus V COM Driver. Ordering Information. Applications. Pinout FN Data Sheet December 7, 2005

ISL Features. Multi-Channel Buffers Plus V COM Driver. Ordering Information. Applications. Pinout FN Data Sheet December 7, 2005 Data Sheet FN6118.0 Multi-Channel Buffers Plus V COM Driver The integrates eighteen gamma buffers and a single V COM buffer for use in large panel LCD displays of 10 and greater. Half of the gamma channels

More information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information HA-22, HA-22 Data Sheet August, 2 FN2894. 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-22/22 comprise a series of operational amplifiers delivering an unsurpassed

More information

HA MHz, PRAM Four Channel Programmable Amplifiers. Features. Applications. Pinout. Ordering Information

HA MHz, PRAM Four Channel Programmable Amplifiers. Features. Applications. Pinout. Ordering Information HA0 Data Sheet August 00 FN89. 0MHz, PRAM Four Channel Programmable Amplifiers The HA0 comprise a series of fourchannel programmable amplifiers providing a level of versatility unsurpassed by any other

More information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,

More information

DATASHEET HA-5104/883. Description. Features. Applications. Ordering Information. Pinout. Low Noise, High Performance, Quad Operational Amplifier

DATASHEET HA-5104/883. Description. Features. Applications. Ordering Information. Pinout. Low Noise, High Performance, Quad Operational Amplifier DATASHEET Low Noise, High Performance, Quad Operational Amplifier FN3710 Rev 1.00 Features This Circuit is Processed in Accordance to MILSTD 883 and is Fully Conformant Under the Provisions of Paragraph

More information

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table TM Data Sheet June 2000 File Number 3990.6 480MHz, SOT-23, Video Buffer with Output Disable The is a very wide bandwidth, unity gain buffer ideal for professional video switching, HDTV, computer monitor

More information

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12.

DATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12. 25MHz Video Buffer NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at -888-INTERSIL or www.intersil.com/tsc DATASHEET FN2924 Rev 8. The HA-533 is a unity

More information

EL5129, EL5329. Multi-Channel Buffers. Features. Applications. Ordering Information FN Data Sheet May 13, 2005

EL5129, EL5329. Multi-Channel Buffers. Features. Applications. Ordering Information FN Data Sheet May 13, 2005 Data Sheet May 3, 25 FN743. Multi-Channel Buffers The EL529 and EL5329 integrate multiple gamma buffers and a single V COM buffer for use in large panel LCD displays of and greater. The EL529 integrates

More information

Single-Ended 16-Channel/Differential 8-Channel CMOS ANALOG MULTIPLEXERS

Single-Ended 16-Channel/Differential 8-Channel CMOS ANALOG MULTIPLEXERS MPC507 MPC50 MPC50 MPC507 Single-ded -Channel/Differential 8-Channel CMOS NLOG MULTIPLEXERS FETURES NLOG OVERVOLTGE PROTECTION: 70Vp-p NO CHNNEL INTERCTION DURING OVERVOLTGE BREK-BEFORE-MKE SWITCHING NLOG

More information

HA-2520, HA-2522, HA-2525

HA-2520, HA-2522, HA-2525 HA-, HA-, HA- Data Sheet September 99 File Number 9. MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-// comprise a series of operational amplifiers delivering an unsurpassed

More information

DATASHEET. Features. Applications. Pin Configurations HS-139RH, HS-139EH. Radiation Hardened Quad Voltage Comparator. FN3573 Rev 6.

DATASHEET. Features. Applications. Pin Configurations HS-139RH, HS-139EH. Radiation Hardened Quad Voltage Comparator. FN3573 Rev 6. DTSHEET Radiation Hardened Quad Voltage Comparator The Radiation Hardened consists of four independent single or dual supply voltage comparators on a single monolithic substrate. The common mode input

More information

DATASHEET HI-539. Features. Applications. Ordering Information. Pinouts. Precision, 4-Channel, Low-Level, Differential Multiplexer

DATASHEET HI-539. Features. Applications. Ordering Information. Pinouts. Precision, 4-Channel, Low-Level, Differential Multiplexer DATASHEET Precision, 4-Channel, Low-Level, Differential Multiplexer The Intersil is a monolithic, 4-Channel, differential multiplexer. Two digital inputs are provided for channel selection, plus an Enable

More information

DATASHEET HI-303. Features. Functional Diagram. Applications Pinout Switch States Shown For A Logic 1 Input. Ordering Information

DATASHEET HI-303. Features. Functional Diagram. Applications Pinout Switch States Shown For A Logic 1 Input. Ordering Information TSHEET HI-33 ual, SPT CMOS nalog Switch The HI-33 switch is a monolithic device fabricated using CMOS technology and the Intersil dielectric isolation process. This switch features break-before-make switching,

More information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information

DATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information DATASHEET 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers FN2894 Rev 1. comprise a series of operational amplifiers delivering an unsurpassed combination of specifications

More information

SGM4582 High Voltage, CMOS Analog Multiplexer

SGM4582 High Voltage, CMOS Analog Multiplexer High Voltage, CMOS nalog Multiplexer GENERL DESCRIPTION The is a high voltage, CMOS analog IC configured as two 4-channel multiplexers. This CMOS device can operate from ±1.8V to ±5.5V dual power supplies

More information

CD4051B, CD4052B, CD4053B

CD4051B, CD4052B, CD4053B CD, CD, CD Data sheet acquired from Harris Semiconductor SCHSD ugust - Revised March [ /Title (CD, CD, CD ) /Subject CMOS nalog ultilexrs/dem ltiplexrs with ogic evel onverion) /uthor ) /Keyords Harris

More information

DATASHEET HA Features. Applications. Pinout. Ordering Information. 3.2µs Sample and Hold Amplifiers. FN2856 Rev.7.

DATASHEET HA Features. Applications. Pinout. Ordering Information. 3.2µs Sample and Hold Amplifiers. FN2856 Rev.7. 3.2µs Sample and Hold Amplifiers NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888TERSIL or www.intersil.com/tsc DATASHEET FN2856 Rev.7.00 The HA-2420

More information

POSSIBLE SUBSTITUTE PRODUCT HA-2842, HA-2544

POSSIBLE SUBSTITUTE PRODUCT HA-2842, HA-2544 OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA2842, HA2544 5MHz, Fast Settling, Unity Gain Stable, Video Operational Amplifier DATASHEET FN2843 Rev 4. The HA2841 is a wideband, unity gain stable, operational

More information

DATASHEET HM Description. Features. Ordering Information. Pinout. 8K x 8 Asynchronous CMOS Static RAM. FN3005 Rev 2.00 Page 1 of 8.

DATASHEET HM Description. Features. Ordering Information. Pinout. 8K x 8 Asynchronous CMOS Static RAM. FN3005 Rev 2.00 Page 1 of 8. DTSHEET 8K x 8 synchronous CMOS Static RM FN3005 Rev 2.00 Features Full CMOS Design Six Transistor Memory Cell Low Standby Supply Current............... 100 Low Operating Supply Current...............

More information

Data Sheet June Features. Pinout

Data Sheet June Features. Pinout NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 888INTERSIL or www.intersil.com/tsc 0Bit Multiplying D/A Converter The AD7533 is a monolithic, low cost,

More information

MARKING RANGE ( C) PACKAGE DWG. # HA-2600 (METAL CAN)

MARKING RANGE ( C) PACKAGE DWG. # HA-2600 (METAL CAN) DATASHEET 2MHz, High Input Impedance Operational Amplifier is an internally compensated bipolar operational amplifier that features very high input impedance (5M coupled with wideband AC performance. The

More information

DATASHEET CD4504BMS. Pinout. Features. Functional Diagram. Description. CMOS Hex Voltage Level Shifter for TTL-to-CMOS or CMOS-to-CMOS Operation

DATASHEET CD4504BMS. Pinout. Features. Functional Diagram. Description. CMOS Hex Voltage Level Shifter for TTL-to-CMOS or CMOS-to-CMOS Operation DATASHEET CD454BMS CMOS Hex Voltage Level Shifter for TTL-to-CMOS or CMOS-to-CMOS Operation FN3336 Rev. Features Pinout High Voltage Type (2V Rating) Independence of Power Supply Sequence Considerations

More information

DATASHEET CD4013BMS. Pinout. Features. Functional Diagram. Applications. Description. CMOS Dual D -Type Flip-Flop. FN3080 Rev 0.

DATASHEET CD4013BMS. Pinout. Features. Functional Diagram. Applications. Description. CMOS Dual D -Type Flip-Flop. FN3080 Rev 0. DATASHEET CD013BMS CMOS Dual D -Type Flip-Flop FN300 Rev 0.00 Features High-Voltage Type (0V Rating) Set-Reset Capability Static Flip-Flop Operation - Retains State Indefinitely With Clock Level Either

More information

DATASHEET HA-5102, HA Pinouts. Ordering Information. Features. Applications. Dual and Quad, 8MHz, Low Noise Operational Amplifiers

DATASHEET HA-5102, HA Pinouts. Ordering Information. Features. Applications. Dual and Quad, 8MHz, Low Noise Operational Amplifiers DATASHEET HA-512, HA-514 Dual and Quad, 8Hz, Low Noise Operational Amplifiers FN2925 Rev 9. October 26, 24 Low noise and high performance are key words describing HA-512 and HA-514. These general purpose

More information

TEMP. PKG. -IN 1 16 S/H CONTROL PART NUMBER RANGE

TEMP. PKG. -IN 1 16 S/H CONTROL PART NUMBER RANGE DATASHEET 7ns, Low Distortion, Precision Sample and Hold Amplifier FN59 Rev 5. The combines the advantages of two sample/ hold architectures to create a new generation of monolithic sample/hold. High amplitude,

More information

DATASHEET CD4027BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS Dual J-KMaster-Slave Flip-Flop. FN3302 Rev 0.

DATASHEET CD4027BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS Dual J-KMaster-Slave Flip-Flop. FN3302 Rev 0. DATASHEET CD7BMS CMOS Dual J-KMaster-Slave Flip-Flop FN33 Rev. Features Pinout High Voltage Type (V Rating) Set - Reset Capability CD7BMS TOP VIEW Static Flip-Flop Operation - Retains State Indefinitely

More information

DATASHEET CD4069UBMS. Features. Pinout. Applications. Functional Diagram. Description. Schematic Diagram. CMOS Hex Inverter

DATASHEET CD4069UBMS. Features. Pinout. Applications. Functional Diagram. Description. Schematic Diagram. CMOS Hex Inverter DATASHEET CD9UBMS CMOS Hex Inverter FN331 Rev. December 199 Features Pinout High Voltage Types (V Rating) Standardized Symmetrical Output Characteristics CD9UBMS TOP VIEW Medium Speed Operation: tphl,

More information

HI Bit, 40 MSPS, High Speed D/A Converter

HI Bit, 40 MSPS, High Speed D/A Converter October 6, 005 Pb-Free and RoHS Compliant HI7 -Bit, 40 MSPS, High Speed D/A Converter Features Throughput Rate......................... 40MHz Resolution................................ -Bit Integral Linearity

More information

DATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00.

DATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00. DATASHEET Low Voltage Reference The is a 1.2V temperature-compensated voltage reference. It uses the band-gap principle to achieve excellent stability and low noise at reverse currents down to 50 A. Applications

More information

HA Microsecond Precision Sample and Hold Amplifier. Features. Applications. Pinouts. Ordering Information. Data Sheet August 24, 2005 FN2857.

HA Microsecond Precision Sample and Hold Amplifier. Features. Applications. Pinouts. Ordering Information. Data Sheet August 24, 2005 FN2857. Data Sheet FN85. Microsecond Precision Sample and Hold Amplifier The was designed for use in precision, high speed data acquisition systems. The circuit consists of an input transconductance amplifier

More information

DATASHEET ISL6208. Features. Applications. Related Literature. Ordering Information. Pinout. High Voltage Synchronous Rectified Buck MOSFET Driver

DATASHEET ISL6208. Features. Applications. Related Literature. Ordering Information. Pinout. High Voltage Synchronous Rectified Buck MOSFET Driver NOT RECOMMENDED FOR NEW DESIGNS POSSIBLE SUBSTITUTE PRODUCT ISL6208 High Voltage Synchronous Rectified Buck MOSFET Driver DATASHEET FN9047 Rev 0.00 The ISL6205 is a high-voltage, high-frequency, dual MOSFET

More information

MAX4528CSA. *Contact factory for availability. Pin Configuration/Functional Diagram/Truth Table IN 3

MAX4528CSA. *Contact factory for availability. Pin Configuration/Functional Diagram/Truth Table IN 3 9-325; Rev ; /98 Low-oltage, Phase-Reversal General Description The low-voltage, CMOS analog IC is configured as a phase-reversal switch and optimized for highspeed applications such as chopper amplifiers.

More information

DATASHEET CD4503BMS. Features. Applications. Functional Diagram. Pinout. CMOS Hex Buffer. FN3335 Rev 0.00 Page 1 of 8. December FN3335 Rev 0.

DATASHEET CD4503BMS. Features. Applications. Functional Diagram. Pinout. CMOS Hex Buffer. FN3335 Rev 0.00 Page 1 of 8. December FN3335 Rev 0. DATASHEET CD503BMS CMOS Hex Buffer CD503BMS is a hex noninverting buffer with 3 state outputs having high sink and source current capability. Two disable controls are provided, one of which controls four

More information

DG200, DG201. CMOS Dual/Quad SPST Analog Switches. Description. Features. Ordering Information. Applications. Pinouts.

DG200, DG201. CMOS Dual/Quad SPST Analog Switches. Description. Features. Ordering Information. Applications. Pinouts. SEMICONDUCTOR DG200, DG20 December 993 CMOS Dual/Quad SPST Analog Switches Features Switches Greater than 28V P-P Signals with ±5 Supplies Break-Before-Make Switching t OFF 250ns, t ON 700ns Typical TTL,

More information

AD7520, AD Bit, 12-Bit, Multiplying D/A Converters. Features. Ordering Information. Pinouts. Data Sheet August 2002 FN3104.

AD7520, AD Bit, 12-Bit, Multiplying D/A Converters. Features. Ordering Information. Pinouts. Data Sheet August 2002 FN3104. AD720, AD72 Data Sheet August 2002 FN304.4 0Bit, 2Bit, Multiplying D/A Converters The AD720 and AD72 are monolithic, high accuracy, low cost 0bit and 2bit resolution, multiplying digitaltoanalog converters

More information

CD22M x 8 x 1 BiMOS-E Crosspoint Switch. Features. Applications. Block Diagram FN Data Sheet January 16, 2006

CD22M x 8 x 1 BiMOS-E Crosspoint Switch. Features. Applications. Block Diagram FN Data Sheet January 16, 2006 CD22M3494 Data Sheet FN2793.7 6 x 8 x BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 28 analog switches capable of handling signals from DC to video. Because of the switch structure, input

More information

Nano Power, Push/Pull Output Comparator

Nano Power, Push/Pull Output Comparator Nano Power, Push/Pull Output Comparator ISL289 The ISL289 is a nano power comparator optimized for low-power applications. This device is designed for single-supply operation from.8v to.v and typically

More information

Quad SPST JFET Analog Switch SW06

Quad SPST JFET Analog Switch SW06 a FEATURES Two Normally Open and Two Normally Closed SPST Switches with Disable Switches Can Be Easily Configured as a Dual SPDT or a DPDT Highly Resistant to Static Discharge Destruction Higher Resistance

More information

DATASHEET CD4098BMS. Description. Features. Applications. Pinout. CMOS Dual Monostable Multivibrator. FN3332 Rev 0.00 Page 1 of 11.

DATASHEET CD4098BMS. Description. Features. Applications. Pinout. CMOS Dual Monostable Multivibrator. FN3332 Rev 0.00 Page 1 of 11. DATASHEET CD9BMS CMOS Dual Monostable Multivibrator Features High Voltage Type (V Rating) Retriggerable/Resettable Capability Trigger and Reset Propagation Delays Independent of RX, CX Triggering from

More information

DATASHEET CD14538BMS. Description. Features. Applications. Functional Diagram. Pinout. CMOS Dual Precision Monostable Multivibrator

DATASHEET CD14538BMS. Description. Features. Applications. Functional Diagram. Pinout. CMOS Dual Precision Monostable Multivibrator DATASHEET CD153BMS CMOS Dual Precision Monostable Multivibrator FN319 Rev. Features High-Voltage Type (V Rating) Retriggerable/Resettable Capability Trigger and Reset Propagation Delays Independent of

More information

CD4063BMS. CMOS 4-Bit Magnitude Comparator. Pinout. Features. Functional Diagram. Applications. Description. December 1992

CD4063BMS. CMOS 4-Bit Magnitude Comparator. Pinout. Features. Functional Diagram. Applications. Description. December 1992 CD3BMS December 99 Features CMOS -Bit Magnitude Comparator Pinout High Voltage Type (V Rating) Expansion to 8,,... N Bits by Cascading Units CD3BMS TOP VIEW Medium Speed Operation - Compares Two -Bit Words

More information

HIP V, 300mA Three Phase High Side Driver. Features. Applications. Ordering Information. Pinout. July 2004

HIP V, 300mA Three Phase High Side Driver. Features. Applications. Ordering Information. Pinout. July 2004 HIP0 Data Sheet July 00 FN. 0V, 00mA Three Phase High Side Driver The HIP0 is a three phase high side N-channel MOSFET driver, specifically targeted for PWM motor control. Two HIP0 may be used together

More information

Features. NOTE: Non-designated pins are no connects and are not electrically connected internally.

Features. NOTE: Non-designated pins are no connects and are not electrically connected internally. OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Data Sheet December 1995, Rev. G EL2001 FN7020 Low Power, 70MHz Buffer Amplifier

More information

ISL6536A. Four Channel Supervisory IC. Features. Applications. Typical Application Schematic. Ordering Information. Data Sheet May 2004 FN9136.

ISL6536A. Four Channel Supervisory IC. Features. Applications. Typical Application Schematic. Ordering Information. Data Sheet May 2004 FN9136. ISL6536A Data Sheet May 2004 FN9136.1 Four Channel Supervisory IC The ISL6536A is a four channel supervisory IC designed to monitor voltages >, = 0.7V. This IC bias range is from 2.7V to 5V but can supervise

More information

DATASHEET. CD4051BMS, CD4052BMS and CD4053BMS analog multiplexers/demultiplexers. Features. Description. Applications. FN3316 Rev 0.

DATASHEET. CD4051BMS, CD4052BMS and CD4053BMS analog multiplexers/demultiplexers. Features. Description. Applications. FN3316 Rev 0. DATASHEET CDBMS, CDBMS, CDBMS CMOS Analog Multiplexers/Demultiplexers Features Logic Level Conversion High-Voltage Types (V Rating) CDBMS Signal -Channel CDBMS Differential -Channel CDBMS Triple -Channel

More information

CA3012. FM IF Wideband Amplifier. Description. Features. Applications. Ordering Information. Schematic Diagram. Pinout.

CA3012. FM IF Wideband Amplifier. Description. Features. Applications. Ordering Information. Schematic Diagram. Pinout. SEMICONDUCTOR CA30 November 99 FM IF Wideband Amplifier Features Exceptionally High Amplifier Gain - Power Gain at.mhz.....................7db Excellent Input Limiting Characteristics - Limiting Voltage

More information

CD4051BMS, CD4052BMS and CD4053BMS analog multiplexers/demultiplexers

CD4051BMS, CD4052BMS and CD4053BMS analog multiplexers/demultiplexers CDBMS, CDBMS CDBMS December Features Logic Level Conversion High-Voltage Types (V Rating) CDBMS Signal -Channel CDBMS Differential -Channel CDBMS Triple -Channel Wide Range of Digital and Analog Signal

More information

AD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K

AD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K a FEATURES 34 MHz Full Power Bandwidth 0.1 db Gain Flatness to 8 MHz 72 db Crosstalk Rejection @ 10 MHz 0.03 /0.01% Differential Phase/Gain Cascadable for Switch Matrices MIL-STD-883 Compliant Versions

More information

HA Quad, 3.5MHz, Operational Amplifier. Description. Features. Applications. Ordering Information. Pinouts. November 1996

HA Quad, 3.5MHz, Operational Amplifier. Description. Features. Applications. Ordering Information. Pinouts. November 1996 SEMICONDUCTOR HA4741 November 1996 Features Slew Rate...............................1.6V/µs Bandwidth................................MHz Input Voltage Noise...................... 9nV/ Hz Input Offset Voltage.........................mV

More information

FEATURES APPLICATIONS. SiP32467, SiP32468 C OUT EN EN GND. Fig. 1 - Typical Application Circuit

FEATURES APPLICATIONS. SiP32467, SiP32468 C OUT EN EN GND. Fig. 1 - Typical Application Circuit 50 mω, Slew Rate Controlled Load Switch in WCSP DESCRIPTION The and are slew rate controlled integrated high side load switches that operate in the input voltage range from 1.2 V to 5.5 V. This series

More information

DATASHEET CD4028BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS BCD-To-Decimal Decoder. FN3303 Rev 0.

DATASHEET CD4028BMS. Features. Pinout. Functional Diagram. Applications. Description. CMOS BCD-To-Decimal Decoder. FN3303 Rev 0. DATASHEET CMOS BCD-To-Decimal Decoder FN Rev. December Features Pinout High Voltage Type (V Rating) BCD-to-Decimal Decoding or Binary-to-Octal Decoding TOP VIEW High Decoded Output Drive Capability Positive

More information

Radiation Hardened Full Bridge N-Channel FET Driver

Radiation Hardened Full Bridge N-Channel FET Driver Radiation Hardened Full Bridge N-Channel FET Driver The is a monolithic, high frequency, medium voltage Full Bridge N-Channel FET Driver IC. The device includes a TTL-level input comparator, which can

More information

HA-2520, HA-2522, HA-2525

HA-2520, HA-2522, HA-2525 HA-, HA-, HA- Data Sheet November, 6 FN894.8 MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-, HA-, HA- comprise a series of operational amplifiers delivering an unsurpassed

More information

Features TEMP. RANGE ( C)

Features TEMP. RANGE ( C) DATASHEET HFA0, HFA09, HFA27, HFA28 Ultra High Frequency Transistor Arrays The HFA0, HFA09, HFA27 and the HFA28 are Ultra High Frequency Transistor Arrays that are fabricated from Intersil Corporation

More information

DATASHEET CD4060BMS. Pinout. Features. Functional Diagram. Oscillator Features. Applications. Description

DATASHEET CD4060BMS. Pinout. Features. Functional Diagram. Oscillator Features. Applications. Description DATASHEET CDBMS CMOS 1 Stage Ripple-Carry Binary Counter/Divider and Oscillator FN3317 Rev. Features Pinout High Voltage Type (V Rating) Common Reset 1MHz Clock Rate at 15V Fully Static Operation Q1 Q13

More information

NOT RECOMMENDED FOR NEW DESIGNS

NOT RECOMMENDED FOR NEW DESIGNS NOT RECOMMENDED FOR NEW DESIGNS POSSIBLE SUBSTITUTE PRODUCTS (ISL6614, ISL6614A, and ISL6614B) Dual Channel Synchronous-Rectified Buck MOSFET Driver DATASHEET FN4838 Rev.1. The HIP662 is a high frequency,

More information

CA3290, CA3290A. BiMOS Dual Voltage Comparators with MOSFET Input, Bipolar Output. Features. Applications. Pinout. Ordering Information

CA3290, CA3290A. BiMOS Dual Voltage Comparators with MOSFET Input, Bipolar Output. Features. Applications. Pinout. Ordering Information Data Sheet September 99 File Number 09.3 BiMOS Dual Voltage Comparators with MOSFET Input, Bipolar Output The CA390A and CA390 types consist of a dual voltage comparator on a single monolithic chip. The

More information

FEATURES APPLICATIONS. SiP32460, SiP32461, SiP32462 C OUT EN EN GND. Fig. 1 - Typical Application Circuit

FEATURES APPLICATIONS. SiP32460, SiP32461, SiP32462 C OUT EN EN GND. Fig. 1 - Typical Application Circuit 50 mω, Slew Rate Controlled Load Switch in WCSP DESCRIPTION The SiP32460,, and SiP32462 are slew rate controlled integrated high side load switches that operate over the input voltage range from 1.2 V

More information

EL2142. Features. Differential Line Receiver. Applications. Ordering Information. Pinout. Data Sheet February 11, 2005 FN7049.1

EL2142. Features. Differential Line Receiver. Applications. Ordering Information. Pinout. Data Sheet February 11, 2005 FN7049.1 Data Sheet FN7049.1 Differential Line Receiver The is a very high bandwidth amplifier designed to extract the difference signal from noisy environments, and is thus primarily targeted for applications

More information

DATASHEET HI1171. Ordering Information. Typical Application Circuit. Pinout. 8-Bit, 40 MSPS, High Speed D/A Converter. FN3662 Rev.3.

DATASHEET HI1171. Ordering Information. Typical Application Circuit. Pinout. 8-Bit, 40 MSPS, High Speed D/A Converter. FN3662 Rev.3. -Bit, 40 MSPS, High Speed D/A Converter Pb-Free and RoHS Compliant DATASHEET FN366 Rev.3.00 Features Throughput Rate.......................... 40MHz Resolution.................................-Bit Integral

More information

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8187 Rev 1.

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8187 Rev 1. DATASHEET X93255 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93255 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a

More information

DATASHEET ISL6700. Features. Ordering Information. Applications. Pinouts. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver

DATASHEET ISL6700. Features. Ordering Information. Applications. Pinouts. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver DATASHEET ISL6700 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver FN9077 Rev.6.00 The ISL6700 is an 80V/1.25A peak, medium frequency, low cost, half-bridge driver IC available in 8-lead

More information

DATASHEET CD22M3494. Features. Applications. Block Diagram. 16 x 8 x 1 BiMOS-E Crosspoint Switch. FN2793 Rev 8.00 Page 1 of 10.

DATASHEET CD22M3494. Features. Applications. Block Diagram. 16 x 8 x 1 BiMOS-E Crosspoint Switch. FN2793 Rev 8.00 Page 1 of 10. DATASHEET CD22M3494 16 x 8 x 1 BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 128 analog switches capable of handling signals from DC to video. Because of the switch structure, input signals

More information

Ultrafast TTL Comparators AD9696/AD9698

Ultrafast TTL Comparators AD9696/AD9698 a FEATURES 4.5 ns Propagation Delay 200 ps Maximum Propagation Delay Dispersion Single +5 V or 5 V Supply Operation Complementary Matched TTL Outputs APPLICATIONS High Speed Line Receivers Peak Detectors

More information

DATASHEET ISL9021A. Features. Pinouts. Applications. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO. FN6867 Rev 2.

DATASHEET ISL9021A. Features. Pinouts. Applications. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO. FN6867 Rev 2. NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL9021A 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO DATASHEET FN6867 Rev 2.00 The ISL9021 is a single LDO providing high performance

More information

NTMKB4895NT3G. Power MOSFET 30 V, 82 A, Single N Channel, ICEPAK

NTMKB4895NT3G. Power MOSFET 30 V, 82 A, Single N Channel, ICEPAK Power MOSFET V,, Single N Channel, Features Low Package Inductance Low R DS(on) to Minimize Conduction Losses Low Capacitance to Minimize Driver Losses Optimized Gate Charge to Minimize Switching Losses

More information

Improved Quad CMOS Analog Switches

Improved Quad CMOS Analog Switches Improved Quad CMOS Analog Switches DESCRIPTION The analog switches are highly improved versions of the industry-standard DG2A, DG22. These devices are fabricated in proprietary silicon gate CMOS process,

More information

POSSIBLE SUBSTITUTE PRODUCT HA-2525, HA-2842

POSSIBLE SUBSTITUTE PRODUCT HA-2525, HA-2842 HA511 1MHz, Low Noise, Operational Amplifiers OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA2525, HA282 DATASHEET FN295 Rev 5. May 2 The HA511 is a dielectrically isolated operational amplifier featuring

More information

HA5023. Dual 125MHz Video Current Feedback Amplifier. Features. Applications. Ordering Information. Pinout. Data Sheet September 30, 2015 FN3393.

HA5023. Dual 125MHz Video Current Feedback Amplifier. Features. Applications. Ordering Information. Pinout. Data Sheet September 30, 2015 FN3393. HA523 Data Sheet September 3, 215 FN3393.9 Dual 125MHz Video Current Feedback Amplifier The HA523 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1

More information

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8186 Rev 1.

DATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8186 Rev 1. DATASHEET X93254 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93254 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a

More information

Shunt Mode Audio Click-and-Pop Eliminator

Shunt Mode Audio Click-and-Pop Eliminator 19-4295; Rev ; 1/8 Shunt Mode udio Click-and-Pop Eliminator General Description The is an audio click-and-pop eliminator for portable multimedia devices. Operating from a 1.7V to 3.6V supply, the connects

More information

DATASHEET. Features. Applications. Related Literature ISL V, Low Quiescent Current, 50mA Linear Regulator. FN7970 Rev 2.

DATASHEET. Features. Applications. Related Literature ISL V, Low Quiescent Current, 50mA Linear Regulator. FN7970 Rev 2. DATASHEET ISL8136 4V, Low Quiescent Current, 5mA Linear Regulator The ISL8136 is a high voltage, low quiescent current linear regulator ideally suited for always-on and keep alive applications. The ISL8136

More information

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches

MAX14759/MAX14761/MAX14763 Above- and Below-the-Rails Low On-Resistance Analog Switches // General Description The // analog switches are capable of passing bipolar signals that are beyond their supply rails. These devices operate from a single +3.V to +5.5V supply and support signals in

More information

DATASHEET HA4314B. Features. Ordering Information. Applications. Truth Table. 400MHz, 4x1 Video Crosspoint Switch. FN3679 Rev 12.

DATASHEET HA4314B. Features. Ordering Information. Applications. Truth Table. 400MHz, 4x1 Video Crosspoint Switch. FN3679 Rev 12. DATASHEET B 4MHz, 4x1 Video Crosspoint Switch FN3679 Rev 12. The B is a very wide bandwidth 4x1 crosspoint switch ideal for professional video switching, HDTV, computer monitor routing, and other high

More information