Specification For Approval

Transcription

1 Specification For Approval Customer : Description : Customer Part No. : Delta Model No. : Safety Model No. : Sample Issue No. : Sample Issue Date : EC FAN GTB040PUD26R N1 GTB040PUD26 05/24/2017 Rev : Please send one copy of this specification back after you signed approval for production pre-arrangement Approved by : Date : Delta Electronics, Inc. No.252, Shangying Road, Guishan Industrial Zone, TEL : Taoyuan City, 33341, Taiwan FAX :

2 *** SAMPLE HISTORY *** CUSTOMER: CUSTOMER P/N: DELTA MODEL:GTB040PUD26R N1 CHECKED REV DESCRIPTION DRAWN ME EE 邱瀞美邱瀞美林科亦 X03 ISSUE SPEC. 05/ / /24 17 APPROVED 顏承偉 05/24 17 ISSUE DATE 05/24 17

3 Electronically Commutated (EC) Fan Centrifugal Fan ψ404 x 257 mm Delta Electronics, Inc. No.252, Shangying Road, Guishan Industrial Zone, Taoyuan City, 33341, Taiwan TEL: FAX: Technical features Input Side Physical Nominal Voltage 3~ 400Vac 50/60Hz Rotation Direction CW, Seen on rotor Input Source 3~ 380Vac - 480Vac Material (Impeller / Frame) Aluminum sheet / Die-cast aluminum Free air 640 W Bearing system Ball bearings Max. load 1000 W Weight (kg) 11.9 Output Side Speed (RPM) 1850 Electrical leads Environmental Via terminal block Qmax. (CMH / CFM) 6001 / 3532 Pmax. (Pa / inaq) 755 / 3.03 Operating temperature range -25 ~ +60 Storage temperature range -40 ~ +70 Noise Qmax Functions Passive power factor correction Control input 0-10VDC / PWM / 4-20mA. Output +10VDC (±10%), max. 10mA. Control voltage output: 0-10VDC. RS485 control bus Alarm relay, Locked rotor protection, Soft start. Speed telling, Frequency generator signal. Safety Safety IP Level EMC Protection class Insulation class Leakage current Motor protection Life expectance UL; cul; TUV IP54 EN /3, EN /3 Ⅰ B <= 3.5 ma Over temperature protected 60,000 hrs at 40 / 15 ~ 65 %RH Voltage / Current monitoring. NOTE : Delta reserves the right to change specifications and other product information without prior notice.

4 Pressure (Pa) Pressure (inaq) GTB040PUD26R N1 P & Q curves Airflow (CFM) Airflow (CMH) Measure data: P [Pa] Q [CMH] N [R.P.M.] P1 [W] I [A] Lp [db(a)] Test Condition: Input Voltage: Nominal Voltage Temperature : Room Temperature Humidity : 65%RH Measured with inlet cone. Noise (Lp) is measured at a distance of one meter from the inlet side.

5 Dimension drawing Label : Fan : Note : 1. Depth of screw : 12 ~16 mm. 2. Cable Diameter : Ø 6.0 ~ Ø 10.0 mm 3. Open the cover and refer to definition of terminal block. UNIT : mm[inch]

6 Definition of terminal block PROTECTIVE EARTHING PROTECTIVE EARTHING Text Functions Power L1 AC main (3~ VAC) L2 AC main (3~ VAC) L3 AC main (3~ VAC) Status NO Alarm relay, open by failure COM Alarm relay, common (2A/250VAC) NC Alarm relay, close by failure Signal RSA RS485-A RSB RS485-B RSA RS485-A RSB RS485-B GND Ground +10V +10V output, MAX 10mA (For external potentiometer) GND Ground FG Frequency generator (FG) signal 0-10V/PWM Speed control,input 0-10VDC 4-20mA Speed control,input 4-20mA OUT Control voltage output 0-10VDC (For external potentiometer)

7 Lead wire connection: PROTECTIVE EARTHING Fan internal M5x0.8 THREAD DEPTH 8mm 3~ VAC 50/60 Hz L1 L2 L3 RELAY WILL BE BREAKED WHEN FAILURE OCCUR RS485 (COMPUTER) PIN1 PIN2 Tacho O/P SIGNAL R>=2K CONTROL O/P PIN6 PIN7 PIN8 PIN9 PIN10 PIN11 1M k 200 M5x0.8 THREAD DEPTH 8mm PROTECTIVE EARTHING

8 Speed setting Full Speed PIN 9 Short PIN6 & PIN9 Fan will run full speed. PIN 6 Voltage Control A PIN 6 PIN 9 Connector 1-10kΩ variable resistor Between +10VDC with GND and 0-10V/PWM Turn the variable resistor,can change the 0-10V/PWM voltage (0 10V) PIN 7 Voltage Control B 0-10V DC Source PIN 9 PIN 7 Use voltage source support DC+ : connector PIN9(+) DC - : connector PIN7(-) 0~10VDC voltage PWM Control PWM Generator Current Control 4-20mA Current Source PIN 9 PIN 7 PIN 10 PIN 7 PWM duty control PWM amplitude is 10VDC(+-5%) Frequency Range is 100Hz 100kHz -PWM duty higher than 15%, fan start up -PWM duty lower than 5%, fan stop 4~20mA Current Control Open 0-10V/PWM PIN - Lower than 4.8 ma Fan Stop - Higher than 5.6 ma Fan Start up - Higher than 19.5 ma Maximum Speed

9 Signal function RS485 control function RS485 control function -Select the control mode of speed, fixed speed or fixed PWM duty -Speed and power consumption feedback. -Allow multiple FANs control and status patrol. Control O/P The analog signal level is the derivative of current control level. Current (ma) Control O/P (VDC) (REF) Voltage/PWM control The speed comparison will control level Voltage (V) PWM (%) Speed (RPM) (REF) ±50RPM ±8% ±5% Current control The speed comparison will control level Current (ma) Speed (RPM) (REF) ±50RPM ±8% ±5% Alarm state NO and COM will OPEN ; NC and COM will CLOSE. FG V CE (sat) = 0.7V MAX. V FG = 30.0V MAX. I C = 5mA MAX. R V FG / I C Frequency generator waveform

10 Control Voltage VS. RPM Curve 2000 RPM VDC Voltage(VDC), PWM duty (% ), 4~20mA table Voltage VDC PWM duty % 4~20 ma ma