UNISONIC TECHNOLOGIES CO., LTD 3544 LINEAR INTEGRATED CIRCUIT

Transcription

1 UNISONIC TECHNOLOGIES CO., LTD 3544 LINEAR INTEGRATED CIRCUIT HEADPHONE AMPLIFIER FOR CD-ROMS DESCRIPTION As a dual headphone amplifier the UTC 3544 is digital-source. The UTC 3544 has a steady gain of 6dB and so it is unnecessary for external gain setting. The UTC 3544 has internal mute function so that it is greatly simplified for prevention of the popping sound when power is turned on and off. To prevent damage from short circuits the UTC 3544 is equipped with thermal shutdown circuit. FEATURES * Internal mute function to prevent popping sounds when *the power is turned on and off. * Built-in thermal shutdown circuit (50 C) to prevent *damage to the IC if a short circuit occurs. ORDERING INFORMATION Ordering Number Lead Free Halogen Free Package Packing 3544L-D08-T 3544G-D08-T DIP-8 Tube G-S08-R SOP-8 Tape Reel MARKING DIP-8 SOP-8 of 9 Copyright 05 Unisonic Technologies Co., Ltd QW-R D

2 PIN DESCRIPTIONS PIN NO. PIN NAME I/O PIN VOLTAGE INTERNAL EQUIVALENT CIRCUIT FUNCTION Vcc OUT O.V Output pin 7 OUT O.V (V CC =5V) 7 0k MUTE I 0.V (When open) Mute control pin (set to low for prevention of popping noise when power is turned on and off). Operating: High Muting: Low(open) 3 IN I.V Input pin 5 IN I.V (V CC =5V) 6 BIAS I/O 4 GND I 8 V CC I.V (V CC =5V) Bias pin (the external 47μF capacitor also serves as the anti-pop time constant, therefore make the proper considerations be changing it). UNISONIC TECHNOLOGIES CO., LTD of 0 QW-R D

3 BLOCK DIAGRAM UNISONIC TECHNOLOGIES CO., LTD 3 of 0 QW-R D

4 ABSOLUTE MAXIMUM RATINGS (Ta=5 C) PARAMETER SYMBOL RATINGS UNIT Applied Voltage V MAX 7.0 V Power Dissipation 450 mw P D Derate above 5 C 4.5 mw/ C Operating Temperature T OPR -5 ~ 75 C Storage Temperature T STG -55 ~ 5 C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING CONDITIONS (Ta=5 C) PARAMETER SYMBOL MIN TYP MAX UNIT Power Supply Voltage V CC V ELECTRICAL CHARACTERISTICS (Ta=5 C, V CC =5.0V, R L =3Ω, V IN = -6dBV, f=khz) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT Mute Pin Control Voltage V TM V Quiescent Current I Q V IN =0Vrms ma Voltage Gain Gv db Voltage Gain Difference Between Channels Gv (DIFF) db Total Harmonic Distortion THD BW=0~0kHz % Rated Output Po R L =3Ω,THD<0.% 5 3 mw Rated Output Po R L =6Ω,THD<0.% 50 6 mw Output Noise Voltage en BW=0~0kHz,Rg=0Ω dbv Channel Separation CS Rg=0Ω 8 90 db Mute Attenuation ATT Rg=0Ω db Ripple Rejection RR f RR =00Hz, V RR = -0dBV db UNISONIC TECHNOLOGIES CO., LTD 4 of 0 QW-R D

5 MEASUREMENT CIRCUIT 3 6 SW7 V 330μ VAC SW5 μ VIN 47μ SW8B A I Q 0μ Vcc OUT BIAS IN SW8A VRR TSD 6dB 6dB BIAS 90K 90K Vcc MUTE 3 6 SW VAC V 3 4 GND OUT MUTE IN VTM 330μ μ SW3 VIN MEASUREMENT CONDITIONS SW TABLE SIGNAL MONITOR SW SW3 SW5 SW7 SW8A SW8B I Q OFF I Q CONDITIONS V TM G VC ON VAC,VAC f=khz,v IN/=-6dBV, V TM =.6V Gvc GVC GVC THD ON VAC,VAC fin=khz,v IN/= -6dBV, V TM =.6V Po ON VAC,VAC fin=khz,v IN/= -6dBV, V TM =.6V Po ON VAC,VAC fin=khz,v IN/= -6dBV, V TM =.6V V NO ON VAC,VAC CS ON ON VAC,VAC VAC,VAC fin=khz,v IN = -6dBV, V TM =.6V fin=khz,v IN = -6dBV, V TM =.6V ATT ON VAC,VAC fin=khz,v IN/= -6dBV, V TM =0.3VB RR ON VAC,VAC V RR = -0dBV, f RR =00Hz UNISONIC TECHNOLOGIES CO., LTD 5 of 0 QW-R D

6 CIRCUIT OPERATION Rising edge timing Rising period A Play period A Descending period Vcc B C OUT VMUTE A: MUTE period(use with MUTE=Low to prevent the popping noise when the power is turned on and off ). B: MUTE release time(used to prevent the popping noise at the release of MUTE with the external C and R and therefore possesses a time constant,so be careful of the timing). C: MUTE start time(also possesses a time constant like the MUTE release time). UNISONIC TECHNOLOGIES CO., LTD 6 of 0 QW-R D

7 APPLICATION EXAMPLE Vcc 330μ C C6 47μ Vcc OUT BIAS IN μ C3 VIN TSD 6dB BIAS 90K 6dB 90K MUTE H:Active L:Mute VMUTE C7 330μ 3 4 OUT MUTE IN GND R 00k C μ μ C5 VIN EXPLANATION OF EXTERNAL COMPONENTS ()Input coupling capacitor (C3 and C5) First determined by the low-band cut-off frequency. Because the input impedance is 80kΩ for this IC, it can be determined by this formula C3(C5)=/(π 80kΩ f) But make sure taking the fluctuations, ambient temperature, etc into consideration. A multi-layered ceramic capacitor is recommended. ()BIAS capacitor(c6) 47μF when Vcc=5V, and 33μF when Vcc=3V. Before changing these values take the sufficient considerations.it is because the electrical characteristics will be adversely affected and popping noise may occur if the capacitance is lowered too much. (3)MUTE pin for anti-pop measures (R and C) An impedance of 90kΩ must be possessed with respect to GND, so the MUTE mode may become unable to be released if R is increased too much. (4)Output coupling capacitor(c and C7) Also determined by the low-band cutoff frequency. Like the output load resistance value R L (a resistor Rx will be inserted,assuming that for output protection or current limiting), it can be calculated by this formula C(C7)=/(π (R L Rx) f) (5)Input gain adjustment resistor(r3 and R4) External resistors R3 and R4 can perform input gain adjustment.the desired gain can be calculated by this formula Gv=60log(90kΩ/(90kΩR3))[dB] UNISONIC TECHNOLOGIES CO., LTD 7 of 0 QW-R D

8 Output Voltage, VOUT (dbv) Quiescent Current, IQ (ma) Bias DC Voltage, VBIAS (V) 3544 LINEAR INTEGRATED CIRCUIT TYPICAL CHARACTERISTICS Quiescent Current vs. Power Supply Voltage Pin DC Current vs. Power Supply Voltage Ta=5 R L =3Ω MUTE: OFF MUTE: ON Ta=5 R L =3Ω Output DC Voltage, VOUT (V) Supply Voltage, Vcc (V) Supply Voltage, Vcc(V) Output Voltage vs. Mute Control Voltage Ta=5 RL=3Ω Vcc=5V VIN=0dBV f=khz Voltage Gain, Gv (db) Voltage Gain vs. Frequency Ta=5 R L =3Ω Vcc=5V 00 k 0k 00k Mute Control Voltage, V TM (V) Frequency, F(Hz) 0 Total Harmonic Distortion vs. Output Voltage ( I ) Ta=5 RL=3Ω Vcc=5V f=0khz 0 Total Harmonic Distortion vs. Output Voltage ( II ) Ta=5 RL=3Ω Vcc=3V f=0khz 0. f=khz 0. f=khz 0.0 f=00hz 0.0 f=00hz Output Voltage, V OUT (dbv) Output Voltage, V OUT (dbv) UNISONIC TECHNOLOGIES CO., LTD 8 of 0 QW-R D

9 TYPICAL CHARACTERISTICS(Cont.) UNISONIC TECHNOLOGIES CO., LTD 9 of 0 QW-R D

10 UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD 0 of 0 QW-R D