WTX-610 Illuminator 6 GHz Multi-Mode Test Transmitter User Manual

Transcription

1 Ver. 3.0 January 2018 WTX-610 Illuminator 6 GHz Multi-Mode Test Transmitter User Manual

2 Page1 Copyright 2018 Consultix Company All Rights Reserved No part of this manual may be produced or transmitted in any form or by any means without prior written consent of Consultix. Trademarks Consultix is a trademark of Consultix Company. All other trademarks mentioned in this manual are the property of their respective holders. Notice The information in this manual is subjected to be changed without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information and recommendations in this manual do not constitute the warranty of any kind, expressed or implied

3 Page2 Contents Overview... 3 Introduction... 3 Key Features... 3 Applications... 3 Safety Compliances & Precautions... 4 Getting Started... 5 Package contents... 5 WTX-610 ILLUMINATOR Panels... 6 General Operations... 7 Preparations... 7 WTX-610 Display Screen... 7 Example test setup... 9 WTX-610 ILLUMINATOR Upgrades Specifications FDD LTE frequency bands... 14

4 Page3 Overview Introduction Consultix WTX-610 illuminator is the gold standard for portable RF signal generators / test transmitters. Using modulated signals makes it versatile tool for myriad applications. Wideband operation up to 6 GHz allows the illuminator to address all your future needs of signal generators / test transmitters even over unlicensed bands for LTE-U and LAA or the CBRS Band. These features combined with the ultra-portable handheld form factor and innovative touch interface for maximum ease of use make the WTX-610 illuminator a convenient choice for laboratory users as well as field applications such as DAS & Small Cells radio planning and testing. The built-in optional wideband power amplifier extends the illuminator s capabilities to missions that requires high power CW test transmitter, whether for odas test and design or for performing outdoor CW model calibration. Key Features CW, LTE & WCDMA modulations 200 to 6000 MHz in a single device 10 Watt (Built-in Option) 1 KHz frequency resolution 1 db Accuracy (Typ.) Key-word upgradeable Light weight < 2 K gm (5 lbs.) Handheld & heavy-duty Touch screen operation Friendly user interface Ergonomic enclosure Applications CW Measurements Walk-Tests IBS Path Loss Measurements DAS Performance Evaluation In-Building Coverage Enhancement General Purpose Signal Generator

5 Page4 Safety Compliances & Precautions In order to avoid damage to your WTX-610 illuminator and to ensure efficient operation of your test transmitters, please make sure to follow the following recommendations and best practices: A. To avoid hazard or damage, only use original accessories with the device. B. Don't touch the antenna during operation as it may alter the radiation pattern. C. The best practice is to connect the antenna before turning-on the RF Power. D. Do not operate in Wet/Very Damp Conditions. E. Do not operate near flammable or explosive materials. F. If you suspect there is a damage to this product, have it inspected only by authorized service personnel or service centers.

6 Page5 Getting Started Package contents Please unpack and inspect the shipping package to make sure that you have received all the parts without damage; the shipping package is shown in table 1. WTX-610 ILLUMINATOR 3G ANTENNA 850/900/1800/1900/2100MHz 12Vdc Power Adapter USB-Mini B Touch Pin 8GB Flash Memory Carrying Case Table 1: WTX-610 ILLUMINATOR Packing List For any issue regarding the shipment package, please contact your nearest Consultix distributer or contact us directly at support@consultix-egypt.com

7 Page6 WTX-610 ILLUMINATOR Panels Figure 1 below depicts the Front Panel of the WTX-610 ILLUMINATOR. N-Type Connector (High power RF output) SMA Connector (Low power RF output) Display Screen a- Front Panel USB Interface Power Switch Charging Interface (12 Vdc) b- Bottom Panel Figure1: WTX-610 ILLUMINATOR User Interface

8 Page7 General Operations Preparations Connect the power adapter to the DC socket Switch On the device by a one-second press on the power switch Before starting RF transmission, please connect the antenna to illuminator. WTX-610 Display Screen Figure 2, depicts the device display Figure2: Consultix Illuminator Main Window User Inputs 1) Freq. : Type in the signal frequency in MHz. 2) Amp. : Type in the required signal level in dbm. 3) Mode: Select the required signal generation mode CW: Select the Continuous Wave (CW) Mode WCDMA: Select the WCDMA Mode - Scr. Code: Type in the scrambling code from 0 to 51. LTE: Select the LTE Mode - Cell ID: Type in the LTE Cell ID from 0 to Band No. : Type in the required B number as per LTE standard bands. Note: User has to choose certain B number to work with Test/commercial phones (optional). Dwelling: Select the Dwelling Mode (Optional)

9 Page8 Note: When switching to LTE or WCDMA modes, the device takes a while after you press RF ON/OFF button. 4) TX Port: Switches between high & low power mode Low: Low power signal generation for indoor applications; -10 dbm to 15 dbm (Standard) High: High Power signal generation for outdoor applications; +20 to +40 dbm (Optional); PA ON/OFF button appears in this mode. 5) RF ON/ OFF: Start/Stop RF signal generation; RF ON status indicator appears on the upper right corner. 6) PA ON/OFF: Turn on/off built-in power amplifier; PA ON status indicator appears on the upper right corner. Warning: Please make sure that a suitable antenna is connected to High power RF port before turning on the built-in power amplifier module. 7) Settings: Enter the device information window where the user can view the device information (Serial Number, HW Version and UI Version) and can activate WCDMA, LTE and Dwelling licenses by typing the license key in the License Key text box as shown in Figure 3 below: Enter the license key Figure3: Consultix Illuminator License Activation

10 Page9 Example test setup Generating LTE signal (only supported in low power mode) Figure 4, depicts an example of generating 5dBm LTE signal at MHz (EARFCN#1301) with Cell ID = 3 using Consultix WTX-610 Multi-mode Illuminator. Figure 4: 5dBm LTE signal generation at MHz 1- Connect the 12Vdc Power Adapter to the DC socket and power on the device 2- On the display screen follow the following steps: Set the operation mode to LTE Choose LTE band number Band No. as per standard LTE bands Type in the required Cell ID (From 0 to 503) Choose the Tx Port to be Low In the Freq. Textbox, type in the signal frequency = MHz. In the Amp. Textbox, type in the signal level = 5 dbm. 3- Toggle RF ON/OFF button to start RF Transmission; LTE waveform will be generated. Note: In order to obtain Consultix Illuminator LTE mode license or any other licenses, please contact support@consultix-egypt.com

11 Page10 4- Start your drive/walk test by holding your receiver/scanner or test phone and getting signal parameters in different locations at venue as depicted in Figure 5 below. DL EARFCN = 1301 Cell ID = 3 Figure 5: A complete Modulated Walk Test using WTX-610 Illuminator and test phone

12 Page11 Generating CW signal using high power mode Figure 6 below depicts an example of generating 40dBm CW signal at 2600MHz using Consultix WTX- 610 Multi-mode Illuminator. Figure 6: 40dBm CW signal generation at 2600MHz 5- Connect the 24Vdc Power Adapter to the charging socket and power on the WTX-610 Illuminator. 6- On the display screen follow the following steps: Set the operation mode to CW Choose the Tx Port to be High ; PA ON/OFF button will be activated. In the Freq. Textbox, type in the signal frequency = 2600 MHz. In the Amp. Textbox, type in the signal level = 40 dbm. 7- Toggle PA ON/OFF button to turn on power amplifier module; PA ON indicator appears on the upper right corner. 8- Toggle RF ON/OFF button to start RF Transmission; RF ON indicator appears on the upper right corner.

13 Page12 In Figure 7, a 2.6GHz CW signal is generated using WTX-610 Illuminator Figure 7: 40 dbm CW signal generation at 2.6GHz 9- Once you have done your test, toggle RF ON/OFF button to stop RF Transmission then turn off power amplifier module by pressing PA ON/OFF button. WTX-610 ILLUMINATOR Upgrades WTX-610 ILLUMINATOR is upgradeable by boot-loader process for any type of arbitrary waveform generations please contact support@consultix-egypt.com to get your appropriate firmware version

14 Page13 Specifications RF Characteristics RF Ports Frequency Range Internal Frequency Accuracy Frequency Step Output Power Level Steps Modualtions LTE Settings LTE BW WCDMA Settings Port 1 Output Power (CW) Port 1 Output Power (Modulated) Port 1 Level Accuarcy Port 1 RF Interface Port 2 Frequency Range Port 2 Output Power (Optional Built-in Output Amplifier) Port 2 Level Accuarcy Port 2 RF Interface Dwelling Mode (Optional) Port 1 (Standard), Port 2 (Optional) 200MHz 6000MHz 1 ppm 1 KHz 1 db Continuous Wave (CW), LTE-FDD(Optional), LTE-TDD(Optional) and W-CDMA (Optional) Cell ID (Synchronization & Reference Signal) and Bandwidth 5MHz (10 MHz Optional) Scrambling Code 200 MHz to 4.8 GHz: -10 dbm to 15 dbm 4.8 GHz to 6 GHz: -10 dbm to 10 dbm 400MHz to 2700 MHz: -10 dbm to 15 dbm +/- 2 db (Typ. 1dB) 50 Ohm SMA Female 350 to 2700 MHz 350 MHz to 2700 MHz: 40 dbm (10 Watt. CW) +/- 2 db (Typ. 1dB) 50 Ohm Type-N Up to ms hopping speed Power supply Input Power Included AC/DC Adapter Physical Characteristics External Dimensions Weight Operating Temperature Interfaces Standard Package 24 VDC /12 VDC (Without Amplifier) 110/220V AC, 50/60 Hz L 220 x W 100 x H 62mm <2 Kgm (5 lbs) with Amplifier -10 to +40 C 1 x Type-N Female, 1 x SMA Female, 1 x USB and 1DC Jack Handheld CW Transmitter, AC/DC Adapter, Tri-band Antenna, Soft case and User Manual

15 Page14 FDD LTE frequency bands BAND NUMBER UPLINK (MHZ) DOWNLINK (MHZ) BANDWIDTH (MHZ) DUPLEX SPACING (MHZ) BAND GAP (MHZ) / n/a

16 Page15 Further Help For any support inquiry, kindly contact: Support: Or contact our distributer covering your region (Check