Test report No. : S-A Page : 2 of 80 Issued date : July 2, 2014 Revised date : July 30, 2014 FCC ID : N43E REVISION HISTORY

Transcription

1

2 Test report No. : S-A Page : 2 of 80 Issued date : July 2, 2014 Revised date : July 30, 2014 FCC ID : N43E REVISION HISTORY Original Test Report No.: S-A Revision Test report No. Date Page revised Contents -(Original) S-A July 2, S-A July 30, , 2, 43, 44 P43, 44: Correction of misdescription Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

3 Test report No. : S-A Page : 3 of 80 Issued date : July 2, 2014 FCC ID : N43E Contents Page SECTION 1: Customer information... 4 SECTION 2: Equipment under test (E.U.T.)... 4 SECTION 3: Test specification, procedures & results... 6 SECTION 4: Operation of E.U.T. during testing... 9 SECTION 5: Conducted emission SECTION 6: Radiated emission SECTION 7: 6dB bandwidth & Occupied bandwidth (99%) SECTION 8: Maximum peak output power SECTION 9: Out of band emissions (Antenna port conducted) SECTION 10: Peak power density Contents of APPENDIXES APPENDIX 1: Data of Radio tests APPENDIX 2: Test instruments APPENDIX 3: Photographs of test setup Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

4 Test report No. : S-A Page : 4 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 1: Customer information Applicant: Company Name : Honda ing Co., Ltd. Address : 6-1, Hagadai, Haga-Machi, Haga-Gun, Tochigi, Japan Telephone Number : Facsimile Number : Contact Person : Tomokazu Takasaka Manufacturer: Company Name : NEC ing, Ltd. Address : 1753 Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa Japan Telephone Number : Facsimile Number : Contact Person : Atsushi Suzuki SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : WLAN CARD Model Number : E Serial Number : Refer to 4.2 in this report. Rating : DC5V Country of Mass-production : Japan Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Receipt Date of Sample : March 7, 2014 Modification of EUT : No modification by the test lab. 2.2 Product description Model: E (referred to as the EUT in this report) is a WLAN CARD. Clock frequency(ies) in the system : kHz, 26MHz Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

5 Test report No. : S-A Page : 5 of 80 Issued date : July 2, 2014 FCC ID : N43E Radio specification: Equipment type : Transceiver Frequency of operation *1) : 2.4GHz: MHz (IEEE b, 11g, 11n-20HT) W52: MHz (IEEE a, 11n-20HT) W53: MHz (IEEE a, 11n-20HT) W56: MHz (IEEE a, 11n-20HT) W58: MHz (IEEE a, 11n-20HT) Bandwidth : 20MHz Channel spacing : 5MHz (2.4GHz), 20MHz (IEEE a, 11n-20HT, 5GHz)) Type of modulation : DSSS, OFDM Antenna type : 2.4GHz band: /4 monopole, 5GHz band: /4 dipole Antenna gain with cable loss : 2.4GHz band: 1.6dBi, 5GHz band: 4.1dBi Antenna connector type : SMD ITU code : D1D, G1D Operation temperature range : 0 to +60 deg.c *1) Refer to the test reports: S-C and S-E for FCC * The EUT does not perform simultaneous transmission of 2.4GHz and 5GHz Wireless LAN. FCC (e) The RF Module has its own regulator. The RF Module is constantly provided voltage (DC1.8V and DC3.3V) through the regulator regardless of input voltage. Therefore, this EUT complies with the requirement. FCC The antenna is not removable from the EUT. Therefore the equipment complies with the requirement Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

6 Test report No. : S-A Page : 6 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 3: Test specification, procedures & results 3.1 Test specification Test specification : FCC Part 15 Subpart C: 2014, final revised on May 1, 2014 and effective June 2, 2014 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section Conducted limits Section Radiated emission limits, general requirements Section Operation within the bands MHz, MHz, and MHz * The revision on May 1, 2014 does not affect the test specification applied to the EUT. 3.2 Procedures & Results Item Test Procedure *1) Specification Remarks Deviation Worst Margin Results 12.4dB Freq.: MHz Conducted Detection: Average ANSI C63.10:2009 FCC N/A emission Phase: L1 Complied Mode: Tx 2462MHz, IEEE g 6dB bandwidth Maximum peak output power Out of band emission & Restricted band edges ANSI C63.10:2009 ANSI C63.10:2009 ANSI C63.10:2009 FCC (a)(2) FCC (b)(3) FCC , (d) & Conducted N/A Complied * See data Conducted N/A Complied Conducted / Radiated N/A 1.7dB Freq.: MHz Polarization: Horizontal Detection: Quasi-Peak Mode: Tx 2462MHz, IEEE g Complied FCC Power density ANSI C63.10:2009 Conducted N/A * See data Complied (e) Note: UL Japan s EMI Work Procedures No.13-EM-W0420 and 13-EM-W0422. *1) These tests were also referred to KDB v03 r01 (FCC), "Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under Addition to standard Item Test Procedure Specification Remarks Worst Margin Results Occupied Bandwidth (99%) ANSI C63.10:2009, RSS-Gen Conducted - - Note: UL Japan s Work Procedures No. 13-EM-W0420 and 13-EM-W0422 * Other than above, no addition, exclusion nor deviation has been made from the standard Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

7 Test report No. : S-A Page : 7 of 80 Issued date : July 2, 2014 FCC ID : N43E Uncertainty The following uncertainties have been calculated to provide a confidence level of 95% using a coverage factor k=2. No.1 SAC *1 /SR *2 No.2 SAC/SR No.3 SAC/SR Item Frequency range (±) (±) (±) Conducted emission 150kHz-30MHz 3.6 db 3.6 db 3.5 db (AC Mains) LISN Radiated emission (Measurement distance: 3m) Radiated emission (Measurement distance: 1m) *1: SAC=Semi-Anechoic Chamber *2: SR= Shielded Room is applied besides radiated emission 9kHz-30MHz 3.7 db 3.7 db 3.6 db 30MHz-300MHz 4.8 db 5.0 db 4.8 db 300MHz-1GHz 5.0 db 5.0 db 4.8 db 1GHz-15GHz 4.9 db 4.9 db 4.9 db 15GHz-18GHz 5.7 db 5.6 db 5.6 db 18GHz-40GHz 5.2 db 4.3 db 4.3 db Conducted emission test The data listed in this test report has enough margin, more than the site margin. Radiated emission test The data listed in this report meets the limits unless the uncertainty is taken into consideration. Antenna port conducted test Power measurement uncertainty above 1GHz for this test was: (±) 1.5dB Spurious emission (Conducted) measurement (below 1GHz) uncertainty for this test was: (±) 1.7dB Spurious emission (Conducted) measurement (1G-3GHz) uncertainty for this test was: (±) 2.3dB Spurious emission (Conducted) measurement (3G-18GHz) uncertainty for this test was: (±) 3.0dB Spurious emission (Conducted) measurement (18G-26.5GHz) uncertainty for this test was: (±) 2.9dB Bandwidth measurement uncertainty for this test was: (±) 5.4% Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

8 Test report No. : S-A Page : 8 of 80 Issued date : July 2, 2014 FCC ID : N43E Test location , Megumigaoka, Hiratsuka-shi, Kanagawa-ken JAPAN Telephone number : Facsimile number : JAB Accreditation No. : RTL02610 FCC Registration No. IC Registration No. Width x Depth x Height (m) Size of reference ground plane (m) / horizontal conducting plane No.1 semi-anechoic chamber D x 11.3 x x m No.2 semi-anechoic chamber D x 11.3 x x m No.3 semi-anechoic chamber D x 7.7 x x 7.7 5m No.4 semi-anechoic chamber x 5.1 x x No.1 shielded room x 4.1 x x No.2 shielded room x 4.1 x x No.3 shielded room x 4.7 x x No.4 shielded room x 4.7 x x No.5 shielded room x 6.4 x x No.6 shielded room x 6.4 x x No.1 measurement room x 4.1 x Test setup, Test data & Test instruments Refer to APPENDIX 1 to 3. Maximum measurement distance Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

9 Test report No. : S-A Page : 9 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 4: Operation of E.U.T. during testing 4.1 Operating mode Test item Mode Tested frequency Worst data mode *1) Power setting *2) Conducted emission Transmitting IEEE g 2462MHz PN9, 24Mbps 13dBm Radiated emission (below 1GHz) *3) Radiated emission Transmitting IEEE b 2412MHz, PN9, 1Mbps 17dBm (above 1GHz) 2437MHz, 2462MHz Transmitting IEEE g 2412MHz, 2437MHz, 2462MHz PN9, 24Mbps 13dBm Transmitting IEEE n-20HT Transmitting IEEE a Transmitting IEEE n-20HT 2412MHz, 2437MHz, 2462MHz 5745MHz, 5785MHz, 5825MHz 5745MHz, 5785MHz, 5825MHz Other items Transmitting IEEE b 2412MHz, 2437MHz, 2462MHz Transmitting IEEE g Transmitting IEEE n-20HT Transmitting IEEE a Transmitting IEEE n-20HT 2412MHz, 2437MHz, 2462MHz 2412MHz, 2437MHz, 2462MHz 5745MHz, 5785MHz, 5825MHz 5745MHz, 5785MHz, 5825MHz PN9, MCS1 (Long GI) PN9, 6Mbps PN9, MCS0 (Long GI) PN9, 1Mbps PN9, 24Mbps PN9, MCS1 (Long GI) PN9, 6Mbps PN9, MCS0 (Long GI) 12dBm 12dBm 12dBm 17dBm 13dBm 12dBm 12dBm 12dBm *1) The worst condition was determined based on the test result of Maximum Peak Output Power. *2) Software for the power setting: WlanCalib ver *3) Test operating mode was determined as follows according to Section 1 of a/b/g/n testing- Managing Complex Regulatory Approvals - of TCB Council Workshop October Justification: The system was configured in typical fashion (as customer would normally use it) for testing Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

10 Test report No. : S-A Page : 10 of 80 Issued date : July 2, 2014 FCC ID : N43E Configuration and peripherals A C D B 1 E 2 AC120V/60Hz * Test data was taken under worse case conditions. Description of EUT and support equipment No. Item Model number Serial number Manufacturer Remarks A WLAN CARD E *1) NEC ing EUT B 3.0G LET E PP Honda ing - C 3.0G LET E NEC - SUB TEST BOARD D WIRE LESS BOARD E OKI CABLE - FPC E AC Adapter UIA UNIFIVE Technology - *1) Antenna terminal conducted tests: 2BE030014K, Conducted/Radiated emission tests: 2BE030022J List of cables used No. Cable Name Length (m) Shield Remarks Cable Connector 1 DC 1.8 Unshielded Unshielded - 2 AC 2.0 Unshielded Unshielded Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

11 Test report No. : S-A Page : 11 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 5: Conducted emission 5.1 Operating environment Test place : See test data (APPENDIX 1) Temperature : See test data (APPENDIX 1) Humidity : See test data (APPENDIX 1) 5.2 Test configuration EUT was placed on a platform of nominal size, 1m by 2.0m, raised 0.8m above the conducting ground plane. The table is made of Styrofoam and covered with polyvinyl chloride. That has very low permittivity. The rear of tabletop was located 40cm to the vertical conducting plane. The rear of peripheral was aligned and was flushed with rear of tabletop. All other surfaces of tabletop were at least 80cm from any other grounded conducting surface. EUT was located 80cm from LISN. Each EUT current-carrying power lead, except the ground (safety) lead, was individually connected through a LISN to the input power source. All unused 50ohm connectors of the LISN were resistively terminated in 50ohm when not connected to the measuring equipment. Photographs of the set up are shown in APPENDIX Test conditions Frequency range : MHz EUT position : Table top 5.4 Test procedure The AC Mains Terminal Continuous disturbance Voltage had been measured with the EUT within a Shielded room. The AC adapter was connected to a Line Impedance Stabilization Network (LISN). An overview sweep with peak detection has been performed. The measurements had been performed with a quasi-peak detector and if required, a CISPR average detector. The conducted emission measurements were made with the following detection of the test receiver. Detection Type : Quasi-Peak/ CISPR Average IF Bandwidth : 9kHz 5.5 Results Summary of the test results : Refer to APPENDIX 1 Pass Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

12 Test report No. : S-A Page : 12 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 6: Radiated emission 6.1 Operating environment Test place : See test data (APPENDIX 1) Temperature : See test data (APPENDIX 1) Humidity : See test data (APPENDIX 1) 6.2 Test configuration EUT was placed on a polystyrene foam platform of nominal size, 0.5m by 0.5m, raised 0.8m above the conducting ground plane. Photographs of the set up are shown in APPENDIX Test conditions Frequency range : 30MHz to 40GHz EUT position : Table top 6.4 Test procedure The Radiated Electric Field Strength intensity has been measured on a semi-anechoic chamber with a ground plane and at a distance of 3m (below 15GHz) / 1m (above 15GHz) (Refer to Figure 1). Measurements were performed with quasi-peak, peak and average detector. The measuring antenna height was varied between 1 and 4m and EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. The measurements were performed for both vertical and horizontal antenna polarization. The radiated emission measurements were made with the following detection. Frequency MHz 1-40GHz 20dBc Detection type Quasi-Peak Peak Average *1) Peak IF Bandwidth 120kHz RBW: 1MHz VBW: 3MHz RBW: 1MHz VBW: 3MHz Detector: RMS RBW: 100kHz VBW: 300kHz *1) Average Power Measurement was measured based on of "Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under The carrier levels and noise levels were confirmed at each position of X, Y and Z axes to see the position of maximum noise, and the test was made at the position that has the maximum noise. 2.4GHz band Antenna polarization Carrier Spurious (Below 1GHz) Spurious (1-15GHz) Spurious (15-18GHz) Horizontal X Y X X X Vertical X Y X X X 5GHz band Antenna polarization Carrier Spurious (1-15GHz) Spurious (15-18GHz) Spurious ( GHz) Horizontal X X X X X Vertical Z Y Y Y X Spurious ( GHz) Spurious ( GHz) Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

13 Test report No. : S-A Page : 13 of 80 Issued date : July 2, 2014 FCC ID : N43E Figure 1. Antenna angle No.3 Semi-Anechoic Chamber (Antenna angle) Radiated Emission (Below 1GHz) 45 deg. 90 deg. Biconical Antenna / Logperiodic Antenna 0 deg. 3m / 3t TurnTable 3m No.3 Semi-Anechoic Chamber (Antenna angle) Radiated Emission (Above 1GHz) 45 deg. 90 deg. Horn Antenna 0 deg. 3m / 3t Measuring Receiver TurnTable 3m No.3 Semi-Anechoic Chamber (Antenna angle) Radiated Emission 45 deg. 90 deg. 0 deg. Horn Antenna 3m / 3t Measuring Receiver TurnTable 1m 6.5 Band edge Band edge level at 2390MHz and MHzis below the limits of FCC and band edge level at 2400MHz, 5725MHz and 5850MHz is below the 20dBc. Refer to the data. 6.6 Results Summary of the test results : Pass * No noise was detected above the 3rd order harmonics. Refer to APPENDIX Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

14 Test report No. : S-A Page : 14 of 80 Issued date : July 2, 2014 FCC ID : N43E SECTION 7: 6dB bandwidth & Occupied bandwidth (99%) Test procedure The bandwidth was measured with a spectrum analyzer connected to the antenna port. The test was measured based on Method 8.1 Option 1 and 8.2 Option 2 of Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under Summary of the test results: Refer to APPENDIX 1 Pass SECTION 8: Maximum peak output power Test procedure The Maximum Peak Output Power was measured with a power meter connected to the antenna port. The test was measured based on Method PKPM1 of Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under Summary of the test results: Refer to APPENDIX 1 Pass SECTION 9: Out of band emissions (Antenna port conducted) Test procedure The Out of Band Emissions was measured with a spectrum analyzer connected to the antenna port. The radio frequency power that is produced by the intentional radiator confirmed 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power, based on a radiated measurement. In the frequency range below 30MHz, RBW was narrowed to separate the noise contents. Then, wide-band noise near the limit was checked separately, however the noise was not detected as shown in the chart. (9kHz-150kHz:RBW=200Hz, 150kHz-30MHz:RBW=10kHz) Summary of the test results: Refer to APPENDIX 1 Pass SECTION 10: Peak power density Test procedure The peak power density was measured with a spectrum analyzer connected to the antenna port. Instrument used : Spectrum Analyzer RBW / VBW : 3kHz / 9.1kHz The test was measured based on Method 10.2 PKPSD of Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS) Operating Under Summary of the test results: Refer to APPENDIX 1 Pass Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

15 Test report No. : S-A Page : 15 of 80 Issued date : July 2, 2014 FCC ID : N43E Contents of APPENDIXES APPENDIX 1: Data of Radio tests Conducted emission 6dB bandwidth Maximum peak output power Radiated emission Spurious emission (Antenna port conducted) Peak power density Occupied bandwidth APPENDIX 2: Test instruments Test instruments APPENDIX 3: Photographs of test setup Conducted emission Radiated emission Pre-check of the worst position Megumigaoka, Hiratsuka-shi, Kanagawa-ken, JAPAN

16 Test Report No : S-A 16 of 80

17 Test Report No : S-A -6dB Bandwidth Test place No.5 Shielded Room Date March 11, 2014 Temperature / Humidity 24deg.C, 39%RH Tatsuya Arai Mode Tx, IEEE802.11b, PN9, worst data mode 1Mbps Freq. [MHz] dB Bandwidth [MHz] Limit [MHz] > > > Tx1_6OBW Tx, 2412MHz Tx2_6OBW Tx, 2437MHz Tx3_6OBW Tx, 2462MHz 17 of 80

18 Test Report No : S-A -6dB Bandwidth Test place No.5 Shielded Room Date March 11, 2014 Temperature / Humidity 24deg.C, 39%RH Tatsuya Arai Mode Tx, IEEE802.11g, PN9, worst data mode 24Mbps Freq. [MHz] dB Bandwidth Limit [MHz] [MHz] > > > Tx1_6OBW Tx, 2412MHz Tx2_6OBW Tx, 2437MHz Tx3_6OBW Tx, 2462MHz 18 of 80

19 Test Report No : S-A -6dB Bandwidth Test place No.5 Shielded Room Date March 11, 2014 Temperature / Humidity 24deg.C, 39%RH Tatsuya Arai Mode Tx, IEEE802.11n-20HT, PN9, worst data mode 1(MCS) Freq. [MHz] dB Bandwidth [MHz] Limit [MHz] > > > Tx1_6OBW Tx, 2412MHz Tx2_6OBW Tx, 2437MHz Tx3_6OBW Tx, 2462MHz 19 of 80

20 Test Report No : S-A -6dB Bandwidth Test place No.5 Shielded Room Date March 11, 2014 Temperature / Humidity 24deg.C, 39%RH Tatsuya Arai Mode Tx, IEEE802.11a, PN9, worst data mode 6Mbps Freq. [MHz] dB Bandwidth [MHz] Limit [MHz] > > > Tx1_6OBW Tx, 5745MHz Tx2_6OBW Tx, 5785MHz Tx3_6OBW Tx, 5825MHz 20 of 80

21 Test Report No : S-A -6dB Bandwidth Test place No.5 Shielded Room Date March 11, 2014 Temperature / Humidity 24deg.C, 39%RH Tatsuya Arai Mode Tx, IEEE802.11n-20HT, PN9, worst data mode 0(MCS) Freq. [MHz] dB Bandwidth [MHz] Limit [MHz] > > > Tx1_6OBW Tx, 5745MHz Tx2_6OBW Tx, 5785MHz Tx3_6OBW Tx, 5825MHz 21 of 80

22 Test Report No : S-A Maximum Peak Conducted Output Power (PKPM1) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11b, PN9, worst data mode : 1 Mbps (* P/M: Power Meter with power sensor) Ch Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss [Pre check] Data rate Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [Mbps] [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss 22 of 80

23 Test Report No : S-A Maximum Conducted Output Power (Reference data for SAR testing) (AVGPM) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11b, PN9, worst data mode : 1 Mbps (* P/M: Power Meter with power sensor, AV: Average) Ch Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor E.I.R.P = Result + Antenna Gain [Pre check] Data rate Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [Mbps] [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor 23 of 80

24 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power 1[Mbps]: Duty Factor =10*log(1/x)= 0.02 db 2[Mbps]: Duty Factor =10*log(1/x)= 0.04 db x:ton/(ton+toff)= 8.61 / 8.65 x:ton/(ton+toff)= 4.40 / 4.45 Tx2_Rate01_Nom Tx2_Rate02_Nom 5.5[Mbps]: Duty Factor =10*log(1/x)= 0.11 db 11[Mbps]: Duty Factor =10*log(1/x)= 0.21 db x:ton/(ton+toff)= 1.72 / 1.77 x:ton/(ton+toff)= 0.95 / 1.00 Tx2_Rate03_Nom Tx2_Rate04_Nom 24 of 80

25 Test Report No : S-A Maximum Peak Conducted Output Power (PKPM1) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11g, PN9, worst data mode : 24 Mbps (* P/M: Power Meter with power sensor) Ch Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss [Pre check] Data rate Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [Mbps] [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss 25 of 80

26 Test Report No : S-A Maximum Conducted Output Power (Reference data for SAR testing) (AVGPM) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11g, PN9, worst data mode : 24 Mbps (* P/M: Power Meter with power sensor, AV: Average) Ch Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor E.I.R.P = Result + Antenna Gain [Pre check] Data rate Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [Mbps] [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor 26 of 80

27 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power 6[Mbps]: Duty Factor =10*log(1/x)= 0.15 db 9[Mbps]: Duty Factor =10*log(1/x)= 0.22 db x:ton/(ton+toff)= 1.43 / 1.48 x:ton/(ton+toff)= 0.96 / 1.01 Tx2_Rate01_Nom Tx2_Rate02_Nom 12[Mbps]: Duty Factor =10*log(1/x)= 0.29 db 18[Mbps]: Duty Factor =10*log(1/x)= 0.42 db x:ton/(ton+toff)= 0.72 / 0.77 x:ton/(ton+toff)= 0.49 / 0.54 Tx2_Rate03_Nom Tx2_Rate04_Nom 27 of 80

28 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power 24[Mbps]: Duty Factor =10*log(1/x)= 0.55 db 36[Mbps]: Duty Factor =10*log(1/x)= 0.79 db x:ton/(ton+toff)= 0.37 / 0.42 x:ton/(ton+toff)= 0.26 / 0.31 Tx2_Rate05_Nom Tx2_Rate06_Nom 48[Mbps]: Duty Factor =10*log(1/x)= 1 db 54[Mbps]: Duty Factor =10*log(1/x)= 1.08 db x:ton/(ton+toff)= 0.20 / 0.25 x:ton/(ton+toff)= 0.18 / 0.23 Tx2_Rate07_Nom Tx2_Rate08_Nom 28 of 80

29 Test Report No : S-A Maximum Peak Conducted Output Power (PKPM1) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11n-20HT, PN9, worst data mode : 1 (MCS) (* P/M: Power Meter with power sensor) Ch Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss [Pre check] Long Guard Interval Mode Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss (MCS) [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Short Guard Interval Mode Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss (MCS) [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss 29 of 80

30 Test Report No : S-A Maximum Conducted Output Power (Reference data for SAR testing) (AVGPM) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11n-20HT, PN9, worst data mode : 7 (MCS) (* P/M: Power Meter with power sensor, AV: Average) Ch Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor E.I.R.P = Result + Antenna Gain [Pre check] Long Guard Interval Mode Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor (MCS) [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Short Guard Interval Mode Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor (MCS) [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor 30 of 80

31 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Long Guard Interval 0(MCS): Duty Factor =10*log(1/x)= 0.16 db 1(MCS): Duty Factor =10*log(1/x)= 0.31 db x:ton/(ton+toff)= 1.34 / 1.39 x:ton/(ton+toff)= 0.69 / 0.74 Tx2_Rate01_Nom_2 Tx2_Rate02_Nom_2 2(MCS): Duty Factor =10*log(1/x)= 0.44 db 3(MCS): Duty Factor =10*log(1/x)= 0.56 db x:ton/(ton+toff)= 0.47 / 0.52 x:ton/(ton+toff)= 0.36 / 0.41 Tx2_Rate03_Nom_2 Tx2_Rate04_Nom_2 31 of 80

32 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Long Guard Interval 4(MCS): Duty Factor =10*log(1/x)= 0.78 db 5(MCS): Duty Factor =10*log(1/x)= 0.98 db x:ton/(ton+toff)= 0.26 / 0.31 x:ton/(ton+toff)= 0.20 / 0.25 Tx2_Rate05_Nom_2 Tx2_Rate06_Nom_2 6(MCS): Duty Factor =10*log(1/x)= 1.05 db 7(MCS): Duty Factor =10*log(1/x)= 1.13 db x:ton/(ton+toff)= 0.18 / 0.23 x:ton/(ton+toff)= 0.17 / 0.22 Tx2_Rate07_Nom_2 Tx2_Rate08_Nom_2 32 of 80

33 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Short Guard Interval 0(MCS): Duty Factor =10*log(1/x)= 0.18 db 1(MCS): Duty Factor =10*log(1/x)= 0.34 db x:ton/(ton+toff)= 1.21 / 1.26 x:ton/(ton+toff)= 0.62 / 0.67 Tx2_Rate01_Nom Tx2_Rate02_Nom 2(MCS): Duty Factor =10*log(1/x)= 0.48 db 3(MCS): Duty Factor =10*log(1/x)= 0.64 db x:ton/(ton+toff)= 0.43 / 0.48 x:ton/(ton+toff)= 0.33 / 0.38 Tx2_Rate03_Nom Tx2_Rate04_Nom 33 of 80

34 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Short Guard Interval 4(MCS): Duty Factor =10*log(1/x)= 0.85 db 5(MCS): Duty Factor =10*log(1/x)= 1.06 db x:ton/(ton+toff)= 0.23 / 0.28 x:ton/(ton+toff)= 0.18 / 0.23 Tx2_Rate05_Nom Tx2_Rate06_Nom 6(MCS): Duty Factor =10*log(1/x)= 1.14 db 7(MCS): Duty Factor =10*log(1/x)= 1.23 db x:ton/(ton+toff)= 0.17 / 0.22 x:ton/(ton+toff)= 0.16 / 0.21 Tx2_Rate07_Nom Tx2_Rate08_Nom 34 of 80

35 Test Report No : S-A Maximum Peak Conducted Output Power (PKPM1) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11a, PN9, worst data mode : 6 Mbps (* P/M: Power Meter with power sensor) Ch Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss [Pre check] Data rate Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [Mbps] [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss 35 of 80

36 Test Report No : S-A Maximum Conducted Output Power (Reference data for SAR testing) (AVGPM) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11a, PN9, worst data mode : 18 Mbps (* P/M: Power Meter with power sensor, AV: Average) Ch Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor E.I.R.P = Result + Antenna Gain [Pre check] Data rate Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [Mbps] [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor 36 of 80

37 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power 6[Mbps]: Duty Factor =10*log(1/x)= 0.15 db 9[Mbps]: Duty Factor =10*log(1/x)= 0.22 db x:ton/(ton+toff)= 1.43 / 1.48 x:ton/(ton+toff)= 0.96 / 1.01 Tx2_Rate01_Nom Tx2_Rate02_Nom 12[Mbps]: Duty Factor =10*log(1/x)= 0.29 db 18[Mbps]: Duty Factor =10*log(1/x)= 0.43 db x:ton/(ton+toff)= 0.72 / 0.77 x:ton/(ton+toff)= 0.49 / 0.54 Tx2_Rate03_Nom Tx2_Rate04_Nom 37 of 80

38 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power 24[Mbps]: Duty Factor =10*log(1/x)= 0.55 db 36[Mbps]: Duty Factor =10*log(1/x)= 0.78 db x:ton/(ton+toff)= 0.37 / 0.42 x:ton/(ton+toff)= 0.26 / 0.31 Tx2_Rate05_Nom Tx2_Rate06_Nom 48[Mbps]: Duty Factor =10*log(1/x)= 1 db 54[Mbps]: Duty Factor =10*log(1/x)= 1.08 db x:ton/(ton+toff)= 0.20 / 0.25 x:ton/(ton+toff)= 0.18 / 0.23 Tx2_Rate07_Nom Tx2_Rate08_Nom 38 of 80

39 Test Report No : S-A Maximum Peak Conducted Output Power (PKPM1) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11n-20HT, PN9, worst data mode : 0 (MCS) (* P/M: Power Meter with power sensor) Ch Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss [Pre check] Long Guard Interval Mode Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss (MCS) [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Short Guard Interval Mode Freq. P/M (Peak) Cable Atten. Result Limit Margin Reading Loss Loss (MCS) [MHz] [dbm] [db] [db] [dbm] [mw] [dbm] [mw] [db] Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss 39 of 80

40 Test Report No : S-A Maximum Conducted Output Power (Reference data for SAR testing) (AVGPM) Test place No.5 Shielded Room Date March 10, 2013 Temperature / Humidity 24deg.C, 37%RH Shinichi Takano Mode Tx, IEEE802.11n-20HT, PN9, worst data mode : 7 (MCS) (* P/M: Power Meter with power sensor, AV: Average) Ch Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Low Mid High Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor E.I.R.P = Result + Antenna Gain [Pre check] Long Guard Interval Mode Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor (MCS) [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Worst Short Guard Interval Mode Freq. P/M (AV) Cable Atten. Duty Result Limit Margin Reading Loss Loss Factor (MCS) [MHz] [dbm] [db] [db] [db] [dbm] [mw] [dbm] [mw] [db] Sample Calculation: Result = Reading + Cable Loss (including the cable(s) customer supplied) + Atten. Loss + Duty Factor 40 of 80

41 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Long Guard Interval 0(MCS): Duty Factor =10*log(1/x)= 0.16 db 1(MCS): Duty Factor =10*log(1/x)= 0.31 db x:ton/(ton+toff)= 1.34 / 1.39 x:ton/(ton+toff)= 0.69 / 0.74 Tx2_Rate01_Nom Tx2_Rate02_Nom 2(MCS): Duty Factor =10*log(1/x)= 0.45 db 3(MCS): Duty Factor =10*log(1/x)= 0.56 db x:ton/(ton+toff)= 0.47 / 0.52 x:ton/(ton+toff)= 0.36 / 0.41 Tx2_Rate03_Nom Tx2_Rate04_Nom 41 of 80

42 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Long Guard Interval 4(MCS): Duty Factor =10*log(1/x)= 0.78 db 5(MCS): Duty Factor =10*log(1/x)= 0.98 db x:ton/(ton+toff)= 0.26 / 0.31 x:ton/(ton+toff)= 0.20 / 0.25 Tx2_Rate05_Nom Tx2_Rate06_Nom 6(MCS): Duty Factor =10*log(1/x)= 1.06 db 7(MCS): Duty Factor =10*log(1/x)= 1.14 db x:ton/(ton+toff)= 0.18 / 0.23 x:ton/(ton+toff)= 0.17 / 0.22 Tx2_Rate07_Nom Tx2_Rate08_Nom 42 of 80

43 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Short Guard Interval 0(MCS): Duty Factor =10*log(1/x)= 0.18 db 1(MCS): Duty Factor =10*log(1/x)= 0.34 db x:ton/(ton+toff)= 1.21 / 1.26 x:ton/(ton+toff)= 0.62 / 0.67 Tx2_Rate01_Nom_2 Tx2_Rate02_Nom_2 2(MCS): Duty Factor =10*log(1/x)= 0.48 db 3(MCS): Duty Factor =10*log(1/x)= 0.62 db x:ton/(ton+toff)= 0.43 / 0.48 x:ton/(ton+toff)= 0.33 / 0.38 Tx2_Rate03_Nom_2 Tx2_Rate04_Nom_2 43 of 80

44 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Caliculation chart for Maximum Conducted Output Power Short Guard Interval 4(MCS): Duty Factor =10*log(1/x)= 0.85 db 5(MCS): Duty Factor =10*log(1/x)= 1.07 db x:ton/(ton+toff)= 0.23 / 0.28 x:ton/(ton+toff)= 0.18 / 0.23 Tx2_Rate05_Nom_2 Tx2_Rate06_Nom_2 6(MCS): Duty Factor =10*log(1/x)= 1.14 db 7(MCS): Duty Factor =10*log(1/x)= 1.22 db x:ton/(ton+toff)= 0.17 / 0.22 x:ton/(ton+toff)= 0.16 / 0.21 Tx2_Rate07_Nom_2 Tx2_Rate08_Nom_2 44 of 80

45 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Burst rate confirmation Tx, IEEE802.11b, PN9, worst data mode 1Mbps duty cycle = / = (99.5%) Tx2_duty1 Tx2_duty2 45 of 80

46 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Calculation chart Tx, IEEE802.11g, PN9, worst data mode 24Mbps Duty Factor Calculation Duty Factor: 20log (1/duty cycle) = 1.1dB duty cycle = / = (88.1%) Tx2_duty1 Tx2_duty2 46 of 80

47 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Calculation chart Tx, IEEE802.11n-20HT, PN9, worst data mode 1(MCS) Duty Factor Calculation Duty Factor: 20log (1/duty cycle) = 0.6dB duty cycle = / = (93.1%) Tx2_duty1 Tx2_duty2 47 of 80

48 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Calculation chart Tx, IEEE802.11a, PN9, worst data mode 6Mbps Duty Factor Calculation Duty Factor: 20log (1/duty cycle) = 0.3dB duty cycle = / = (96.6%) Tx2_duty1 Tx2_duty2 48 of 80

49 Test place No.5 Shielded Room Date March 7, 2013 Temperature / Humidity 22deg.C, 34%RH Shinichi Takano Test Report No : S-A Duty Factor Calculation chart Tx, IEEE802.11n-20HT, PN9, worst data mode 0(MCS) Duty Factor Calculation Duty Factor: 20log (1/duty cycle) = 0.3dB duty cycle = / = (96.3%) Tx2_duty1 Tx2_duty2 49 of 80

50 Test Report No : S-A Radiated Emission Test place No.3 Semi Anechoic Chamber No.3 Semi Anechoic Chamber Date March 10, 2014 March 11, 2014 Temperature / Humidity 21 deg.c, 41 %RH 20 deg.c, 33 %RH Tatsuya Arai Tatsuya Arai Mode Tx, 2412 MHz Tx, IEEE802.11b (* PK: Peak, AV: Average, QP: Quasi-Peak) Polarity Frequency Detector Reading Ant.Fac. Loss Gain Result Limit Margin Height Angle Remark [MHz] [dbuv] [db/m] [db] [db] [dbuv/m] [dbuv/m] [db] [cm] [deg] Hori PK Hori PK Hori PK Hori PK Hori PK Hori PK Hori PK Hori AV Hori AV Hori AV Hori AV Hori AV Hori AV Hori AV Vert PK Vert PK Vert PK Vert PK Vert PK Vert PK Vert PK Vert AV Vert AV Vert AV Vert AV Vert AV Vert AV Vert AV Result = Reading + Ant.Fac. + Loss (Cable + Attenuator + Filter - Distance factor(above 15GHz)) - Gain(Amprifier) Distance factor : 15GHz -40GHz : 20log(3.0m/1.0m)= 9.5dB *Other frequency noises omitted in this report were not seen or have enough margin (more than 20dB) 20dBc Data Sheet (RBW 100kHz, VBW 300kHz) Polarity Frequency Detector Reading Ant.Fac. Loss Gain Result Limit Margin Remark [MHz] [dbuv] [db/m] [db] [db] [dbuv/m] [dbuv/m] [db] Hori PK Hori PK Vert PK Vert PK Result = Reading + Ant.Fac. + Loss (Cable + Attenuator + Filter) - Gain(Amprifier) 50 of 80

51 Test Report No : S-A Radiated Emission Test place No.3 Semi Anechoic Chamber No.3 Semi Anechoic Chamber Date March 10, 2014 March 11, 2014 Temperature / Humidity 21 deg.c, 41 %RH 20 deg.c, 33 %RH Tatsuya Arai Tatsuya Arai Mode Tx, 2437 MHz Tx, IEEE802.11b (* PK: Peak, AV: Average, QP: Quasi-Peak) Polarity Frequency Detector Reading Ant.Fac. Loss Gain Result Limit Margin Height Angle Remark [MHz] [dbuv] [db/m] [db] [db] [dbuv/m] [dbuv/m] [db] [cm] [deg] Hori PK Hori PK Hori PK Hori PK Hori PK Hori PK Hori PK Hori AV Hori AV Hori AV Hori AV Hori AV Hori AV Hori AV Vert PK Vert PK Vert PK Vert PK Vert PK Vert PK Vert PK Vert AV Vert AV Vert AV Vert AV Vert AV Vert AV Vert AV Result = Reading + Ant.Fac. + Loss (Cable + Attenuator + Filter - Distance factor(above 15GHz)) - Gain(Amprifier) Distance factor : 15GHz -40GHz : 20log(3.0m/1.0m)= 9.5dB *Other frequency noises omitted in this report were not seen or have enough margin (more than 20dB) 51 of 80