MAINTENANCE MANUAL MDX POWER AMPLIFIER BOARDS 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz)

Transcription

1 MAINTENANCE MANUAL MDX POWER AMPLIFIER BOARDS 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz) TABLE OF CONTENTS Page DESCRIPTION... 1 CIRCUIT ANALYSIS... 1 SERVICE NOTES... 2 PARTS LIST... 3 OUTLINE DIAGRAM... 4 SCHEMATIC DIAGRAM... 5 DESCRIPTION The Power Amplifier Board (A4) used in the MDX radio is housed in a cavity running parallel to the side of the radio main casting assembly. Refer to the combination manual for a complete mechanical layout of the radio. The PA Board amplifies the driver output from the RF Board (approximately 13 watts) to a level of approximately 40 watts, over the frequency range of MHz. There are no tuning adjustments on the board. The board consist of a single stage RF power amplifier. Also included on the board are two multi-pin connectors used to distribute non-amplifier related signals in the radio. Two SMB connectors are used to apply drive to and take RF output from the amplifier. The MHz range of frequencies is covered by three groups of PA Boards: 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz) CIRCUIT ANALYSIS The driver output from the RF Board (13 watts, 50 ohms impedance) is matched to the base of transistor Q1 by capacitors C10, C11, C15 and a 50 ohm microstrip. Inductor L2 provides a bias return for class "C" operation. A network consisting of capacitor C19 and resistor R1 enhances stability. Once the drive is amplified to approximately 45 watts by Q1, it is matched back up to 50 ohms by capacitors C7, C8, C12, C13/C17, C5/C18, C6 and the 50 ohm microstrip. Capacitor C4 is a DC blocking capacitor, which keeps DC voltage from appearing at the amplifier output. Supply voltage (A+) is applied to the collector of power transistor Q1 through a network consisting of inductor L1 and capacitors C1, C2, C3, C14 and C16. In addition to enhancing stability, these components also prevent RF from getting onto the A+ line. The amplifier output is fed back to the radio RF Board where it passes through the antenna switch, low pass filter and directional coupler before being applied to the antenna connector. Supply voltage (A+) is applied through 6-pin connector J4 by feedthru capacitor assembly Z903. Other non-amplifier related signals are routed through the PA Board for distribution to other boards in the radio. These include A+, switched A+, relay and volume/squelch HI. A wiring harness plugs into connector J3 for this purpose. 1

2 SERVICE NOTES This amplifier can be easily checked without removing it from the radio. RF input (at connector J1) and output (at connector J2) impedances are 50 ohms. Remover all power from the radio when servicing the PA Board. The radio power switch does not remove A+ power from the board. There are 12 chip mica capacitors on this PA Board. If any are removed, replace them with a new part since they are easily damaged. Apply them in the exact positions shown in the outline diagram. Failure to do this will have an adverse effect on amplifier gain, bandwidth and efficiency. PA TRANSISTOR REPLACEMENT 1. Remove the two retaining screws securing PA transistor Q1 to the chassis assembly. 5. Replace the transistor mounting screws, leaving them loose at this time. Align the leads on the transistor being replaced with the microstrip. Position each lead so that a maximum amount of lead is in contact with the microstrip. Tighten each mounting screw to 4 ±1 inch-pounds. 6. "Tin" the 6 transistor leads and then using 2% silver solder. Solder each lead to the printed wire board. 7. Torque the mounting screws to 6 inch-pounds. Remove any flux left on the circuit board. NOTE The PA transistor contains Beryllium Oxide, a TOXIC substance. If the ceramic or other encapsulation is opened, crushed, broken or abraded, the escaping dust may be hazardous if inhaled. Use care when replacing the transistor. 2. Unsolder the six leads of the transistor and remove it from the printed wire board. Be careful not to damage the board. 3. Remove all excess solder from the board near Q1 and clean the board to allow the new transistor to be positioned properly. Refer to the Figure and trim the new transistor leads (if required) to the same lead lengths of the transistor just removed PIN 1. EMITTER 2. COLLECTOR 3. EMITTER 4. BASE 4. Apply silicon grease to the back of the replacement transistor and place the transistor in the mounting cutout. Make sure that the base and collector leads are not reversed. PA TRANSISTOR LEAD IDENTIFICATION Copyright April 1994, Ericsson GE Mobile Communications Inc. 2

3 PARTS LIST LBI POWER AMPLIFIER BOARD 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz) Issue 1 SYMBOL PART NUMBER DESCRIPTION 19D904792G1, G CAPACITORS C1 19A702236P42 Ceramic: 47 pf ±5%, 50 VDCW, temp coef ±30 PPM. SYMBOL PART NUMBER DESCRIPTION TX PA Kit 344A4256G4 ( MHz) TRANSISTOR Q1 344A3948P1 Power Transistor, NPN, Silicon, 50 Watt, UHF MISCELLANEOUS A702364P208 Screw, Machine, Pan Head, Steel. 2 19A700033P3 Washer, lock, External tooth. C2 19A702052P33 Ceramic: 0.1 µf ±10%, 50 VDCW. C3 and C4 19A705108P36 Mica Chip: 91 pf ±5%, 500 VDCW, temp coef PPM. C5 19A705108P206 Mica Chip: 2.2pF ±0.25pF, 500 VDCW, temp coef PPM/ C. C6 19A705108P11 Mica: 8.2 pf ±5%, 500 VDCW. C7 and C8 19A705108P23 Mica Chip: 27 pf ±5%, 500 VDCW, temp coef PPM/ C. C9 19A705108P35 Mica: 82 pf ±5%, 500 VDCW, temp coef PPM/ C. C10 19A705108P24 Mica Chip: 30 pf ±5%, 500 VDCW, temp coef PPM/ C. C11 19A705108P8 Mica: 6.2 pf ±.25 pf, 500 VDCW. C12 19A705108P7 Mica Chip: 5.6 pf ± 0.25 pf, 500 VDCW. C13 19A705108P13 Mica Chip: 10 pf ±%5, 500 VDCW, temp coef PPM/ C. C14 19A702052P28 Ceramic: µf ±10%, 50 VDCW. C15 19A705108P25 Mica Chip: 33 pf ±5%, 500 VDCW, temp coef PPM/ C. C16 344A4196P Electrolytic, 10 µf. (Used in G1) JACKS J1 and J2 19B801342P1 Connector, RF. (Used in G1). J3 19A700072P33 Printed wire: 7 contacts 2.5 amps; Sim to Molex (Used in G1).Molex (Used in G1). F J INDUCTORS L1 19B800891P2 Coil, RF Choke: sim to Paul Smith SK L2 19B800891P6 Coil, RF:.084 µh; sim to Paul Smith SK RESISTORS R1 19A700113P7 Composition: 4.7 ohms ±5%, 1/2 w. (Used in G1). *COMPONENTS ADDED, DELECTED OR CHANGED BY PRODUCTION CHANGES 3

4 OUTLINE DIAGRAM COMPONENT SIDE Power Amplifier Board 19D904792G1, G2 & G3 (19D904792, Rev. 2) (19D904690, Component Side, Rev. 3) 4

5 SCHEMATIC DIAGRAM LBI Power Amplifier 19D904792G1, G2 & G3 (19D904791, Rev. 0) 5

6 Printed in U.S.A. 6