EXPERIMENT 3 - Part I: DSB-SC Amplitude Modulation

Size: px
Start display at page:

Download "EXPERIMENT 3 - Part I: DSB-SC Amplitude Modulation"

Transcription

1 OBJECTIVE To generate DSB-SC amplitude modulated signal. EXPERIMENT 3 - Part I: DSB-SC Amplitude Modulation PRELIMINARY DISCUSSION In the modulation process, the message signal (the baseband voice, video, etc.) modifies a higher-frequency signal called the carrier, which is usually a sinusoidal wave. As the name suggests, in amplitude modulation, the information signal varies the amplitude of the carrier. Figure 1 below shows a simple message signal, an unmodulated carrier, and DSB-SC amplitude modulated signal. Figure 1 Mathematically, DSB-SC signal can be given as: DSB-SC = the message x the carrier Let the message signal be denoted by m(t) and the carrier signal be denoted by c(t), then DSB-SC amplitude modulated signal u(t) is given by u( t) m( t) c( t) Note that DSB-SC offers a substantial power saving over DSB by not sending the carrier. THE EXPERIMENT In this experiment you'll use the Emona Telecoms-Trainer 101 to generate a real DSB-SC signal by implementing its mathematical model. You'll examine the DSB-SC signal using the scope and compare it to the original message. You'll do the same with speech for the message instead of a simple sinewave. 1

2 Equipment Emona Telecoms-Trainer 101 (plus power-pack) Dual channel 20MHz oscilloscope two Emona Telecoms-Trainer 101 oscilloscope leads assorted Emona Telecoms-Trainer 101 patch leads Procedure Part A - Generating a DSB-SC signal using a simple message 1. Gather a set of the equipment listed above. 2. Set up the scope. Ensure that: the Trigger Source control is set to the CH1 (or INT) position. the Mode control is set to the CH1 position. 3. Connect the set-up shown in Figure 2 below. Figure 2 With values, Figure 2 implements the following equation: DSB-SC = 4Vp-p 2kHz sine x 4Vp-p 100kHz sine. Note that in class, we assume the carrier has the following form: c( t) Ac cos(2 fct c ). If c / 2, c( t) Acsin(2 fct). 4. Adjust the scope's Timebase control to view two or so cycles of the Master Signals module's 2kHz SINE output. 5. Set the scope's Mode control to the DUAL position to view the DSB-SC signal out of the Multiplier module as well as the message signal. 6. Set the scope's Channel 1 Vertical Attenuation control to the 1V/div position and the Channel 2 Vertical Attenuation control to the 2V/div position. 7. Draw the two waveforms to scale in the space provided. 8. Use the scope's Channel 1 Vertical Position control to overlay the message with the DSB-SC signal's envelopes and compare them. Question 1 The DSB-SC signal is a complex waveform consisting of more than one signal. Is one of the signals a 2kHz sinewave? Explain your answer. Question 2 For the given inputs to the Multiplier module, how many sinewaves does the DSB-SC signal consist of, and what are their frequencies? 2

3 Question 3 State advantage(s) of DSB-SC signals over DSB signals? Part B - Generating a DSB-SC signal using speech This part of the experiment lets you see what a DSB-SC signal looks like when modulated by speech. 9. Disconnect the plugs to the Master Signals module's 2kHz SINE output. 10. Connect them to the Speech module's output as shown in Figure 3 below. Remember: Dotted lines show leads already in place. Figure Set the scope's Timebase control to the 2ms/div position. 12. Talk, sing or hum while watching the scope's display. 3

4 EXPERIMENT 3 - Part II: DSB-SC Demodulation OBJECTIVE To demodulate DSB-SC amplitude modulated signal via product detector and to investigate effects of the carrier synchronization on the product detector s performance. PRELIMINARY DISCUSSION DSB-SC signals are demodulated using a circuit called a product detector (though product demodulator is a more appropriate name) and its basic block diagram is shown in Figure 1 below. Other names for this type of demodulation include a synchronous detector and switching detector. Figure 1 As its name implies, the product detector uses multiplication. The incoming DSB-SC signal is multiplied by a pure sinewave that must be the same frequency as the DSB-SC signal's suppressed carrier. This sinewave is generated by the receiver and is known as the local carrier, cl () t. Throughout this experiment, we assume the carrier has the following form: c( t) sin(2 fct). Note that when c( t) c ( t), the output of the multiplier is given by L 1 sin(4 ft c ) 1 x( t) m( t) c( t) cl ( t) m( t) m( t) other terms 2 2 In order to recover the message, a low-pass filter is then used to reject higher frequency components. THE EXPERIMENT In this experiment, you'll connect the DSB-SC signal as generated in Part I.A to the product detector's input and compare the demodulated output to the original message and the DSB-SC signal's envelopes. Then, you'll investigate the effect on the product detector's performance of an unsynchronized local carrier. Equipment Emona Telecoms-Trainer 101 (plus power-pack) Dual channel 20MHz oscilloscope two Emona Telecoms-Trainer 101 oscilloscope leads assorted Emona Telecoms-Trainer 101 patch leads one set of headphones (stereo) Procedure Part A - Setting up the DSB-SC modulator To experiment with DSB-SC demodulation you need a DSB-SC signal first. Thus, generate a DSB-SC signal as in the Part I.A of the experiment. 4

5 Part B - Recovering the message using a product detector 1. Locate the Tuneable Low-pass Filter module and set its Gain control to about the middle of its travel. 2. Turn the Tuneable Low-pass Filter module's soft Cut-off Frequency Adjust control fully clockwise. 3. Modify the set-up as shown in Figure 2 below. Remember: Dotted lines show leads already in place. Figure 2 The entire set-up is represented by the block diagram in Figure 3 below. It highlights the fact that the modulator's carrier is "stolen" to provide the product detector's local carrier. This means that the two carriers are synchronized which is necessary for DSB-SC communications to work. Figure 3 4. Draw the demodulated DSB-SC signal to scale. Part C - Transmitting and recovering speech using DSB-SC 5. Adjust the scope's Trigger Source control to the CH1 position. 6. Modify the set-up as shown in Figure 4 below. 5

6 Figure 4 7. Set the scope's Timebase control to the 2ms/div position. 8. Turn the Buffer module's Gain control fully anti-clockwise. 9. Without wearing the headphones, plug them into the Buffer module's headphone socket. 10. Put the headphones on. 11. As you perform the next step, set the Buffer module's Gain control to a comfortable sound level. 12. Talk, sing or hum while watching the scope's display and listening on the headphones. Part D - Carrier synchronization Crucial to the correct operation of a DSB-SC communications system is the synchronization between the modulator's carrier signal and the product detector's local carrier. Any phase or frequency difference between the two signals adversely affects the system's performance. The effect of phase errors If there's a phase error between the carriers, that is, c( t) sin(2 fct) and cl( t) sin(2 fct ). The output of the multiplier: 1 x( t) m( t) c( t) cl( t) m( t)cos( ) other terms 2 Note that if the phase difference between the carriers is 90 0, the message signal will be lost. 13. Turn the Buffer module's Gain control fully anti-clockwise again. 14. Return the scope's Timebase control to about the 0.1ms/div position. 15. Locate the Phase Shifter module and set its Phase Change control to the 180 position. 16. Set the Phase Shifter module's Phase Adjust control to about the middle of its travel. 17. Modify the set-up as shown in Figure 5 below. 6

7 Figure 5 The entire set-up can be represented by the block diagram in Figure 6 below. The Phase Shifter module allows a phase error between the DSB-SC modulator's carrier and the product detector's local carrier to be introduced. Figure Slowly increase the Buffer module's gain until you can comfortably hear the demodulated 2kHz tone. 19. Vary the Phase Shifter module's Phase Adjust control left and right while watching and listening to the effect on the recovered message. 20. Adjust the Phase Shifter module's Phase Adjust control until the recovered message is biggest. Question 1 Given the size of the recovered message's amplitude, what is the likely phase error between the two carriers? 7

8 21. Adjust the Phase Shifter module's Phase Adjust control until the recovered message is smallest. Question 2 Given the size of the recovered message's new amplitude, what is the likely phase error between the two carriers? The effect of frequency errors There may be a frequency error between the DSB-SC signal's carrier and the product detector's local carrier. If the error is small (say 0.1Hz) the two signals will alternately reinforce and cancel each other which can render the message periodically inaudible but otherwise intelligible. If the frequency error is larger (say 5Hz) the message is reasonably intelligible but fidelity is poor. When frequency errors are large, intelligibility is seriously affected. 22. Locate the VCO module and set its Range control to the HI position. 23. Set the VCO module's Frequency Adjust control to about the middle of its travel. 24. Modify the set-up as shown in Figure 7 below. Figure 7 The entire set-up can be represented by the block diagram in Figure 8 below. The VCO module allows the local oscillator to be completely frequency (and phase) independent of the DSB-SC modulator. 8

9 Figure Vary the VCO module's Frequency Adjust control left and right and observe the effect on the recovered message. 26. If you're not doing so already, listen to the recovered message using the headphones. 27. Use the display of the recovered message on the scope and your hearing to try to get VCO module's frequency as close as possible to the transmitter's carrier frequency. Tip: If you can't remember what 2kHz sounds like, disconnect the plug to the VCO module's output and connect it to the Master Signals modules 100kHz SINE output for a couple of seconds. This will mean that the two carriers are the same again and the message will be recovered. 28. Disconnect the plugs to the Master Signals module's 2kHz SINE output and connect them to the Speech module's output. 29. Talk, sing, etc into the microphone while varying the VCO module's Frequency Adjust control and listen to the effect of an unsynchronized local carrier on speech. Question 3 Derive the expression for the output of DSB-SC demodulator in the case of frequency errors. 9

EXPERIMENT 4 - Part I: DSB Amplitude Modulation

EXPERIMENT 4 - Part I: DSB Amplitude Modulation OBJECTIVE To generate DSB amplitude modulated signal. EXPERIMENT 4 - Part I: DSB Amplitude Modulation PRELIMINARY DISCUSSION In an amplitude modulation (AM) communications system, the message signal is

More information

3 - Using the Telecoms-Trainer 101 to model equations

3 - Using the Telecoms-Trainer 101 to model equations Name: Class: 3 - Using the Telecoms-Trainer 101 to model equations Experiment 3 Using the Telecoms-Trainer 101 to model equations Preliminary discussion This may surprise you, but mathematics is an important

More information

EXPERIMENT 2: Frequency Shift Keying (FSK)

EXPERIMENT 2: Frequency Shift Keying (FSK) EXPERIMENT 2: Frequency Shift Keying (FSK) 1) OBJECTIVE Generation and demodulation of a frequency shift keyed (FSK) signal 2) PRELIMINARY DISCUSSION In FSK, the frequency of a carrier signal is modified

More information

EXPERIMENT 1: Amplitude Shift Keying (ASK)

EXPERIMENT 1: Amplitude Shift Keying (ASK) EXPERIMENT 1: Amplitude Shift Keying (ASK) 1) OBJECTIVE Generation and demodulation of an amplitude shift keyed (ASK) signal 2) PRELIMINARY DISCUSSION In ASK, the amplitude of a carrier signal is modified

More information

Figure 1: a BPSK signal (below) and the message (above)

Figure 1: a BPSK signal (below) and the message (above) EXPERIMENT 3: Quadrature Phase Shift Keying (QPSK) 1) OBJECTIVE Generation and demodulation of a quadrature phase shift keyed (QPSK) signal. 2) PRELIMINARY DISCUSSION QPSK is a form of phase modulation

More information

17 - Binary phase shift keying

17 - Binary phase shift keying Name: Class: 17 - Binary phase shift keying Experiment 17 Binary Phase Shift Keying Preliminary discussion Experiments 15 and 16 show that the AM and FM modulation schemes can be used to transmit digital

More information

Volumes 1 and 2 Experiments in Modern Analog & Digital Telecommunications Barry Duncan

Volumes 1 and 2 Experiments in Modern Analog & Digital Telecommunications Barry Duncan Emona 101 Trainer SAMPLE Lab Manual Volumes 1 and 2 Experiments in Modern Analog & Digital Telecommunications Barry Duncan Emona 101 Trainer SAMPLE Lab Manual Volumes 1 and 2 Experiments in Modern Analog

More information

Experiment 19 Binary Phase Shift Keying

Experiment 19 Binary Phase Shift Keying Experiment 19 Binary Phase Shift Keying Preliminary discussion Experiments 17 and 18 show that the AM and FM modulation schemes can be used to transmit digital signals and this allows for the channel to

More information

CME312- LAB Manual DSB-SC Modulation and Demodulation Experiment 6. Experiment 6. Experiment. DSB-SC Modulation and Demodulation

CME312- LAB Manual DSB-SC Modulation and Demodulation Experiment 6. Experiment 6. Experiment. DSB-SC Modulation and Demodulation Experiment 6 Experiment DSB-SC Modulation and Demodulation Objectives : By the end of this experiment, the student should be able to: 1. Demonstrate the modulation and demodulation process of DSB-SC. 2.

More information

AMPLITUDE MODULATION

AMPLITUDE MODULATION AMPLITUDE MODULATION PREPARATION...2 theory...3 depth of modulation...4 measurement of m... 5 spectrum... 5 other message shapes.... 5 other generation methods...6 EXPERIMENT...7 aligning the model...7

More information

OBJECTIVES EQUIPMENT LIST

OBJECTIVES EQUIPMENT LIST 1 Reception of Amplitude Modulated Signals AM Demodulation OBJECTIVES The purpose of this experiment is to show how the amplitude-modulated signals are demodulated to obtain the original signal. Also,

More information

Problems from the 3 rd edition

Problems from the 3 rd edition (2.1-1) Find the energies of the signals: a) sin t, 0 t π b) sin t, 0 t π c) 2 sin t, 0 t π d) sin (t-2π), 2π t 4π Problems from the 3 rd edition Comment on the effect on energy of sign change, time shifting

More information

Emona DATEx. Volume 1 Experiments in Modern Analog & Digital Telecommunications. Barry Duncan

Emona DATEx. Volume 1 Experiments in Modern Analog & Digital Telecommunications. Barry Duncan Emona DATEx Lab Manual Volume 1 Experiments in Modern Analog & Digital Telecommunications Barry Duncan . Emona DATEx Lab Manual Volume 1 Experiments in Modern Analog & Digital Telecommunications Barry

More information

PRODUCT DEMODULATION - SYNCHRONOUS & ASYNCHRONOUS

PRODUCT DEMODULATION - SYNCHRONOUS & ASYNCHRONOUS PRODUCT DEMODULATION - SYNCHRONOUS & ASYNCHRONOUS INTRODUCTION...98 frequency translation...98 the process...98 interpretation...99 the demodulator...100 synchronous operation: ω 0 = ω 1...100 carrier

More information

Amplitude Modulation. Ahmad Bilal

Amplitude Modulation. Ahmad Bilal Amplitude Modulation Ahmad Bilal 5-2 ANALOG AND DIGITAL Analog-to-analog conversion is the representation of analog information by an analog signal. Topics discussed in this section: Amplitude Modulation

More information

PHASE DIVISION MULTIPLEX

PHASE DIVISION MULTIPLEX PHASE DIVISION MULTIPLEX PREPARATION... 70 the transmitter... 70 the receiver... 71 EXPERIMENT... 72 a single-channel receiver... 72 a two-channel receiver... 73 TUTORIAL QUESTIONS... 74 Vol A2, ch 8,

More information

Amplitude Modulation Chapter 2. Modulation process

Amplitude Modulation Chapter 2. Modulation process Question 1 Modulation process Modulation is the process of translation the baseband message signal to bandpass (modulated carrier) signal at frequencies that are very high compared to the baseband frequencies.

More information

CARRIER ACQUISITION AND THE PLL

CARRIER ACQUISITION AND THE PLL CARRIER ACQUISITION AND THE PLL PREPARATION... 22 carrier acquisition methods... 22 bandpass filter...22 the phase locked loop (PLL)....23 squaring...24 squarer plus PLL...26 the Costas loop...26 EXPERIMENT...

More information

Costas Loop. Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier

Costas Loop. Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier Costas Loop Modules: Sequence Generator, Digital Utilities, VCO, Quadrature Utilities (2), Phase Shifter, Tuneable LPF (2), Multiplier 0 Pre-Laboratory Reading Phase-shift keying that employs two discrete

More information

CME 312-Lab Communication Systems Laboratory

CME 312-Lab Communication Systems Laboratory Objective: By the end of this experiment, the student should be able to: 1. Demonstrate the Modulation and Demodulation of the AM. 2. Observe the relation between modulation index and AM signal envelope.

More information

AC : DEVELOPING DIGITAL/ANALOG TELECOMMUNICA- TION LABORATORY

AC : DEVELOPING DIGITAL/ANALOG TELECOMMUNICA- TION LABORATORY AC 2011-2119: DEVELOPING DIGITAL/ANALOG TELECOMMUNICA- TION LABORATORY Dr. Yuhong Zhang, Texas Southern University Yuhong Zhang is an assistant professor at Texas Southern University Xuemin Chen, Texas

More information

The Sampling Theorem:

The Sampling Theorem: The Sampling Theorem: Aim: Experimental verification of the sampling theorem; sampling and message reconstruction (interpolation). Experimental Procedure: Taking Samples: In the first part of the experiment

More information

cosω t Y AD 532 Analog Multiplier Board EE18.xx Fig. 1 Amplitude modulation of a sine wave message signal

cosω t Y AD 532 Analog Multiplier Board EE18.xx Fig. 1 Amplitude modulation of a sine wave message signal University of Saskatchewan EE 9 Electrical Engineering Laboratory III Amplitude and Frequency Modulation Objectives: To observe the time domain waveforms and spectra of amplitude modulated (AM) waveforms

More information

Experiment Five: The Noisy Channel Model

Experiment Five: The Noisy Channel Model Experiment Five: The Noisy Channel Model Modified from original TIMS Manual experiment by Mr. Faisel Tubbal. Objectives 1) Study and understand the use of marco CHANNEL MODEL module to generate and add

More information

Part I - Amplitude Modulation

Part I - Amplitude Modulation EE/CME 392 Laboratory 1-1 Part I - Amplitude Modulation Safety: In this lab, voltages are less than 15 volts and this is not normally dangerous to humans. However, you should assemble or modify a circuit

More information

Receiver Architectures

Receiver Architectures Receiver Architectures Modules: VCO (2), Quadrature Utilities (2), Utilities, Adder, Multiplier, Phase Shifter (2), Tuneable LPF (2), 100-kHz Channel Filters, Audio Oscillator, Noise Generator, Speech,

More information

EE 460L University of Nevada, Las Vegas ECE Department

EE 460L University of Nevada, Las Vegas ECE Department EE 460L PREPARATION 1- ASK Amplitude shift keying - ASK - in the context of digital communications is a modulation process which imparts to a sinusoid two or more discrete amplitude levels. These are related

More information

DSBSC GENERATION. PREPARATION definition of a DSBSC viewing envelopes multi-tone message... 37

DSBSC GENERATION. PREPARATION definition of a DSBSC viewing envelopes multi-tone message... 37 DSBSC GENERATION PREPARATION... 34 definition of a DSBSC... 34 block diagram...36 viewing envelopes... 36 multi-tone message... 37 linear modulation...38 spectrum analysis... 38 EXPERIMENT... 38 the MULTIPLIER...

More information

Outline. Communications Engineering 1

Outline. Communications Engineering 1 Outline Introduction Signal, random variable, random process and spectra Analog modulation Analog to digital conversion Digital transmission through baseband channels Signal space representation Optimal

More information

CHAPTER 2! AMPLITUDE MODULATION (AM)

CHAPTER 2! AMPLITUDE MODULATION (AM) CHAPTER 2 AMPLITUDE MODULATION (AM) Topics 2-1 : AM Concepts 2-2 : Modulation Index and Percentage of Modulation 2-3 : Sidebands and the Frequency Domain 2-4 : Single-Sideband Modulation 2-5 : AM Power

More information

Emona Telecoms-Trainer ETT-101

Emona Telecoms-Trainer ETT-101 EXPERIMENTS IN MODERN COMMUNICATIONS Emona Telecoms-Trainer ETT-101 Multi-Experiment Single Board Telecommunications Trainer for Technical College and Technical High School Students EMONA INSTRUMENTS www.ett101.com

More information

EE 400L Communications. Laboratory Exercise #7 Digital Modulation

EE 400L Communications. Laboratory Exercise #7 Digital Modulation EE 400L Communications Laboratory Exercise #7 Digital Modulation Department of Electrical and Computer Engineering University of Nevada, at Las Vegas PREPARATION 1- ASK Amplitude shift keying - ASK - in

More information

Communication Systems Lab

Communication Systems Lab LAB MANUAL Communication Systems Lab (EE-226-F) Prepared by: Varun Sharma (Lab In-charge) Dayal C. Sati (Faculty In-charge) B R C M CET BAHAL DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING Page

More information

Exercise 2: FM Detection With a PLL

Exercise 2: FM Detection With a PLL Phase-Locked Loop Analog Communications Exercise 2: FM Detection With a PLL EXERCISE OBJECTIVE When you have completed this exercise, you will be able to explain how the phase detector s input frequencies

More information

EE-4022 Experiment 2 Amplitude Modulation (AM)

EE-4022 Experiment 2 Amplitude Modulation (AM) EE-4022 MILWAUKEE SCHOOL OF ENGINEERING 2015 Page 2-1 Student objectives: EE-4022 Experiment 2 Amplitude Modulation (AM) In this experiment the student will use laboratory modules to implement operations

More information

German Jordanian University Department of Communication Engineering Digital Communication Systems Lab. CME 313-Lab

German Jordanian University Department of Communication Engineering Digital Communication Systems Lab. CME 313-Lab German Jordanian University Department of Communication Engineering Digital Communication Systems Lab CME 313-Lab Experiment 7 Binary Frequency-shift keying (BPSK) Eng. Anas Al-ashqar Dr. Ala' Khalifeh

More information

Charan Langton, Editor

Charan Langton, Editor Charan Langton, Editor SIGNAL PROCESSING & SIMULATION NEWSLETTER Baseband, Passband Signals and Amplitude Modulation The most salient feature of information signals is that they are generally low frequency.

More information

Pulse-Width Modulation (PWM)

Pulse-Width Modulation (PWM) Pulse-Width Modulation (PWM) Modules: Integrate & Dump, Digital Utilities, Wideband True RMS Meter, Tuneable LPF, Audio Oscillator, Multiplier, Utilities, Noise Generator, Speech, Headphones. 0 Pre-Laboratory

More information

Speech, music, images, and video are examples of analog signals. Each of these signals is characterized by its bandwidth, dynamic range, and the

Speech, music, images, and video are examples of analog signals. Each of these signals is characterized by its bandwidth, dynamic range, and the Speech, music, images, and video are examples of analog signals. Each of these signals is characterized by its bandwidth, dynamic range, and the nature of the signal. For instance, in the case of audio

More information

TIMS-301 USER MANUAL. Telecommunications Instructional Modelling System

TIMS-301 USER MANUAL. Telecommunications Instructional Modelling System TIMS-301 R MANUAL Telecommunications Instructional Modelling System TIMS-301 R MANUAL Issue Number 1.4 February 2002 Published by: EMONA INSTRUMENTS PTY LTD a.c.n. 001 728 276 86 Parramatta Road Camperdown

More information

ANALOG COMMUNICATION

ANALOG COMMUNICATION ANALOG COMMUNICATION TRAINING LAB Analog Communication Training Lab consists of six kits, one each for Modulation (ACL-01), Demodulation (ACL-02), Modulation (ACL-03), Demodulation (ACL-04), Noise power

More information

PRINCIPLES OF COMMUNICATION SYSTEMS LAB

PRINCIPLES OF COMMUNICATION SYSTEMS LAB PRINCIPLES OF COMMUNICATION SYSTEMS LAB LAB MANUAL (EE-230-F) IV SEM ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT OF ELECTRICAL & ELECTRONICS DRONACHARYA COLLEGE OF ENGINEERING KHENTAWAS, GURGAON-123506

More information

Fundamentals of Communication Systems SECOND EDITION

Fundamentals of Communication Systems SECOND EDITION GLOBAL EDITIO Fundamentals of Communication Systems SECOD EDITIO John G. Proakis Masoud Salehi 78 Effect of oise on Analog Communication Systems Chapter 6 The noise power is P n = ow we can find the output

More information

AM Limitations. Amplitude Modulation II. DSB-SC Modulation. AM Modifications

AM Limitations. Amplitude Modulation II. DSB-SC Modulation. AM Modifications Lecture 6: Amplitude Modulation II EE 3770: Communication Systems AM Limitations AM Limitations DSB-SC Modulation SSB Modulation VSB Modulation Lecture 6 Amplitude Modulation II Amplitude modulation is

More information

Amplitude Modulation II

Amplitude Modulation II Lecture 6: Amplitude Modulation II EE 3770: Communication Systems Lecture 6 Amplitude Modulation II AM Limitations DSB-SC Modulation SSB Modulation VSB Modulation Multiplexing Mojtaba Vaezi 6-1 Contents

More information

ELG3175: Introduction to Communication Systems. Laboratory II: Amplitude Modulation

ELG3175: Introduction to Communication Systems. Laboratory II: Amplitude Modulation Introduction: ELG3175: Introduction to Communication Systems Laboratory II: Amplitude Modulation In this lab, we shall investigate some fundamental aspects of the conventional AM and DSB-SC modulation

More information

Lecture 6. Angle Modulation and Demodulation

Lecture 6. Angle Modulation and Demodulation Lecture 6 and Demodulation Agenda Introduction to and Demodulation Frequency and Phase Modulation Angle Demodulation FM Applications Introduction The other two parameters (frequency and phase) of the carrier

More information

AC LAB ECE-D ecestudy.wordpress.com

AC LAB ECE-D ecestudy.wordpress.com PART B EXPERIMENT NO: 1 AIM: PULSE AMPLITUDE MODULATION (PAM) & DEMODULATION DATE: To study Pulse Amplitude modulation and demodulation process with relevant waveforms. APPARATUS: 1. Pulse amplitude modulation

More information

Operating Manual Ver 1.1

Operating Manual Ver 1.1 Frequency Modulation and Demodulation Trainer ST2203 Operating Manual Ver 1.1 An ISO 9001 : 2000 company 94-101, Electronic Complex Pardesipura, Indore- 452010, India Tel : 91-731- 2570301/02, 4211100

More information

Code No: R Set No. 1

Code No: R Set No. 1 Code No: R05220405 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2007 ANALOG COMMUNICATIONS ( Common to Electronics & Communication Engineering and Electronics & Telematics) Time: 3 hours

More information

UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering

UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 8 AMPLITUDE MODULATION AND DEMODULATION OBJECTIVES The focus of this lab is to familiarize the student

More information

Exercise 2: Demodulation (Quadrature Detector)

Exercise 2: Demodulation (Quadrature Detector) Analog Communications Angle Modulation and Demodulation Exercise 2: Demodulation (Quadrature Detector) EXERCISE OBJECTIVE When you have completed this exercise, you will be able to explain demodulation

More information

EE-4022 Experiment 3 Frequency Modulation (FM)

EE-4022 Experiment 3 Frequency Modulation (FM) EE-4022 MILWAUKEE SCHOOL OF ENGINEERING 2015 Page 3-1 Student Objectives: EE-4022 Experiment 3 Frequency Modulation (FM) In this experiment the student will use laboratory modules including a Voltage-Controlled

More information

Modulations Analog Modulations Amplitude modulation (AM) Linear modulation Frequency modulation (FM) Phase modulation (PM) cos Angle modulation FM PM Digital Modulations ASK FSK PSK MSK MFSK QAM PAM Etc.

More information

Introduction to Amplitude Modulation

Introduction to Amplitude Modulation 1 Introduction to Amplitude Modulation Introduction to project management. Problem definition. Design principles and practices. Implementation techniques including circuit design, software design, solid

More information

Twelve voice signals, each band-limited to 3 khz, are frequency -multiplexed using 1 khz guard bands between channels and between the main carrier

Twelve voice signals, each band-limited to 3 khz, are frequency -multiplexed using 1 khz guard bands between channels and between the main carrier Twelve voice signals, each band-limited to 3 khz, are frequency -multiplexed using 1 khz guard bands between channels and between the main carrier and the first channel. The modulation of the main carrier

More information

MTI 7601 PAM Modulation and Demodulation

MTI 7601 PAM Modulation and Demodulation Page 1 of 1 MTI 7601 PAM Modulation and Demodulation Contents Aims of the Exercise Learning about the functioning principle of the pulse-amplitude modulation (sampling, time division multiplex operation)

More information

Amplitude Modulation Fundamentals

Amplitude Modulation Fundamentals 3 chapter Amplitude Modulation Fundamentals In the modulation process, the baseband voice, video, or digital signal modifies another, higher-frequency signal called the carrier, which is usually a sine

More information

Modulation Methods Frequency Modulation

Modulation Methods Frequency Modulation Modulation Methods Frequency Modulation William Sheets K2MQJ Rudolf F. Graf KA2CWL The use of frequency modulation (called FM) is another method of adding intelligence to a carrier signal. While simple

More information

(b) What are the differences between FM and PM? (c) What are the differences between NBFM and WBFM? [9+4+3]

(b) What are the differences between FM and PM? (c) What are the differences between NBFM and WBFM? [9+4+3] Code No: RR220401 Set No. 1 1. (a) The antenna current of an AM Broadcast transmitter is 10A, if modulated to a depth of 50% by an audio sine wave. It increases to 12A as a result of simultaneous modulation

More information

Chapter 3. Amplitude Modulation Fundamentals

Chapter 3. Amplitude Modulation Fundamentals Chapter 3 Amplitude Modulation Fundamentals Topics Covered 3-1: AM Concepts 3-2: Modulation Index and Percentage of Modulation 3-3: Sidebands and the Frequency Domain 3-4: AM Power 3-5: Single-Sideband

More information

Amplitude Modulation, II

Amplitude Modulation, II Amplitude Modulation, II Single sideband modulation (SSB) Vestigial sideband modulation (VSB) VSB spectrum Modulator and demodulator NTSC TV signsals Quadrature modulation Spectral efficiency Modulator

More information

German Jordanian University. Department of Communication Engineering. Digital Communication Systems Lab. CME 313-Lab. Experiment 8

German Jordanian University. Department of Communication Engineering. Digital Communication Systems Lab. CME 313-Lab. Experiment 8 German Jordanian University Department of Communication Engineering Digital Communication Systems Lab CME 313-Lab Experiment 8 Binary Frequency-shift keying (BPSK) Eng. Anas Al-ashqar Dr. Ala' Khalifeh

More information

Modulation is the process of impressing a low-frequency information signal (baseband signal) onto a higher frequency carrier signal

Modulation is the process of impressing a low-frequency information signal (baseband signal) onto a higher frequency carrier signal Modulation is the process of impressing a low-frequency information signal (baseband signal) onto a higher frequency carrier signal Modulation is a process of mixing a signal with a sinusoid to produce

More information

4.1 REPRESENTATION OF FM AND PM SIGNALS An angle-modulated signal generally can be written as

4.1 REPRESENTATION OF FM AND PM SIGNALS An angle-modulated signal generally can be written as 1 In frequency-modulation (FM) systems, the frequency of the carrier f c is changed by the message signal; in phase modulation (PM) systems, the phase of the carrier is changed according to the variations

More information

Experiment One: Generating Frequency Modulation (FM) Using Voltage Controlled Oscillator (VCO)

Experiment One: Generating Frequency Modulation (FM) Using Voltage Controlled Oscillator (VCO) Experiment One: Generating Frequency Modulation (FM) Using Voltage Controlled Oscillator (VCO) Modified from original TIMS Manual experiment by Mr. Faisel Tubbal. Objectives 1) Learn about VCO and how

More information

Universitas Sumatera Utara

Universitas Sumatera Utara Amplitude Shift Keying & Frequency Shift Keying Aim: To generate and demodulate an amplitude shift keyed (ASK) signal and a binary FSK signal. Intro to Generation of ASK Amplitude shift keying - ASK -

More information

Elements of Communication System Channel Fig: 1: Block Diagram of Communication System Terminology in Communication System

Elements of Communication System Channel Fig: 1: Block Diagram of Communication System Terminology in Communication System Content:- Fundamentals of Communication Engineering : Elements of a Communication System, Need of modulation, electromagnetic spectrum and typical applications, Unit V (Communication terminologies in communication

More information

COMMUNICATION SYSTEMS (EE-226-F)

COMMUNICATION SYSTEMS (EE-226-F) COMMUNICATION SYSTEMS (EE-226-F) LAB MANUAL IV SEMESTER Department Of Electronics & Communication Engg Dronach harya College Of Engineering Khentawas, Gurgaon 123506 LIST OF EXPERIMENTS S.No. NAME OF THE

More information

B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering)

B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering) Code: 13A04404 R13 B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering) Time: 3 hours Max. Marks: 70 PART A

More information

Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)

Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE) Department of Electronics & Telecommunication Engg. LAB MANUAL SUBJECT:-DIGITAL COMMUNICATION SYSTEM [BTEC-501] B.Tech V Semester [2013-14] (Branch: ETE) KCT COLLEGE OF ENGG & TECH., FATEHGARH PUNJAB TECHNICAL

More information

DELTA MODULATION. PREPARATION principle of operation slope overload and granularity...124

DELTA MODULATION. PREPARATION principle of operation slope overload and granularity...124 DELTA MODULATION PREPARATION...122 principle of operation...122 block diagram...122 step size calculation...124 slope overload and granularity...124 slope overload...124 granular noise...125 noise and

More information

ELEC3242 Communications Engineering Laboratory Amplitude Modulation (AM)

ELEC3242 Communications Engineering Laboratory Amplitude Modulation (AM) ELEC3242 Communications Engineering Laboratory 1 ---- Amplitude Modulation (AM) 1. Objectives 1.1 Through this the laboratory experiment, you will investigate demodulation of an amplitude modulated (AM)

More information

3.1 Introduction 3.2 Amplitude Modulation 3.3 Double Sideband-Suppressed Carrier Modulation 3.4 Quadrature-Carrier Multiplexing 3.

3.1 Introduction 3.2 Amplitude Modulation 3.3 Double Sideband-Suppressed Carrier Modulation 3.4 Quadrature-Carrier Multiplexing 3. Chapter 3 Amplitude Modulation Wireless Information Transmission System Lab. Institute of Communications Engineering g National Sun Yat-sen University Outline 3.1 Introduction 3. Amplitude Modulation 3.3

More information

1B Paper 6: Communications Handout 2: Analogue Modulation

1B Paper 6: Communications Handout 2: Analogue Modulation 1B Paper 6: Communications Handout : Analogue Modulation Ramji Venkataramanan Signal Processing and Communications Lab Department of Engineering ramji.v@eng.cam.ac.uk Lent Term 16 1 / 3 Modulation Modulation

More information

TIMS: Introduction to the Instrument

TIMS: Introduction to the Instrument TIMS: Introduction to the Instrument Modules: Audio Oscillator, Speech, Adder, Wideband True RMS Meter, Digital Utilities 1 Displaying a Signal on the PicoScope 1. Turn on TIMS. 2. Computer: Start > All

More information

2011 PSW American Society for Engineering Education Conference

2011 PSW American Society for Engineering Education Conference Communications Laboratory with Commercial Test and Training Instrument Peter Kinman and Daniel Murdock California State University Fresno Abstract A communications laboratory course has been designed around

More information

LAB Assignment No. 6: TO STUDY GENERATION OF DOUBLE SIDE BAND AMPLITUDE MODULATE (AM) WAVEFORMS, USING DSB/SSB TRANSMITTER

LAB Assignment No. 6: TO STUDY GENERATION OF DOUBLE SIDE BAND AMPLITUDE MODULATE (AM) WAVEFORMS, USING DSB/SSB TRANSMITTER LAB Assignment No. 6: TO STUDY GENERATION OF DOUBLE SIDE BAND AMPLITUDE MODULATE (AM) WAVEFORMS, USING DSB/SSB TRANSMITTER APPARATUS: Oscilloscope DSB/SSB Traine Power supply Connecting leads THEORY: A

More information

EECS 307: Lab Handout 2 (FALL 2012)

EECS 307: Lab Handout 2 (FALL 2012) EECS 307: Lab Handout 2 (FALL 2012) I- Audio Transmission of a Single Tone In this part you will modulate a low-frequency audio tone via AM, and transmit it with a carrier also in the audio range. The

More information

Experiment 7: Frequency Modulation and Phase Locked Loops

Experiment 7: Frequency Modulation and Phase Locked Loops Experiment 7: Frequency Modulation and Phase Locked Loops Frequency Modulation Background Normally, we consider a voltage wave form with a fixed frequency of the form v(t) = V sin( ct + ), (1) where c

More information

ANALOG (DE)MODULATION

ANALOG (DE)MODULATION ANALOG (DE)MODULATION Amplitude Modulation with Large Carrier Amplitude Modulation with Suppressed Carrier Quadrature Modulation Injection to Intermediate Frequency idealized system Software Receiver Design

More information

EC310 Security Exercise 20

EC310 Security Exercise 20 EC310 Security Exercise 20 Introduction to Sinusoidal Signals This lab demonstrates a sinusoidal signal as described in class. In this lab you will identify the different waveform parameters for a pure

More information

Communication Engineering Prof. Surendra Prasad Department of Electrical Engineering Indian Institute of Technology, Delhi

Communication Engineering Prof. Surendra Prasad Department of Electrical Engineering Indian Institute of Technology, Delhi Communication Engineering Prof. Surendra Prasad Department of Electrical Engineering Indian Institute of Technology, Delhi Lecture - 10 Single Sideband Modulation We will discuss, now we will continue

More information

NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES

NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES Course : EET 24 Communications Electronics Module : AM Tx and

More information

Experiment 02: Amplitude Modulation

Experiment 02: Amplitude Modulation ECE316, Experiment 02, 2017 Communications Lab, University of Toronto Experiment 02: Amplitude Modulation Bruno Korst - bkf@comm.utoronto.ca Abstract In this second laboratory experiment, you will see

More information

Communication Channels

Communication Channels Communication Channels wires (PCB trace or conductor on IC) optical fiber (attenuation 4dB/km) broadcast TV (50 kw transmit) voice telephone line (under -9 dbm or 110 µw) walkie-talkie: 500 mw, 467 MHz

More information

UNIT-2 Angle Modulation System

UNIT-2 Angle Modulation System UNIT-2 Angle Modulation System Introduction There are three parameters of a carrier that may carry information: Amplitude Frequency Phase Frequency Modulation Power in an FM signal does not vary with modulation

More information

EE452 Senior Capstone Project: Integration of Matlab Tools for DSP Code Generation. Kwadwo Boateng Charles Badu. May 8, 2006

EE452 Senior Capstone Project: Integration of Matlab Tools for DSP Code Generation. Kwadwo Boateng Charles Badu. May 8, 2006 EE452 Senior Capstone Project: Integration of Matlab Tools for DSP Code Generation Kwadwo Boateng Charles Badu May 8, 2006 Bradley University College of Engineering and Technology Electrical and Computer

More information

CS311: Data Communication. Transmission of Analog Signal - I

CS311: Data Communication. Transmission of Analog Signal - I CS311: Data Communication Transmission of Analog Signal - I by Dr. Manas Khatua Assistant Professor Dept. of CSE IIT Jodhpur E-mail: manaskhatua@iitj.ac.in Web: http://home.iitj.ac.in/~manaskhatua http://manaskhatua.github.io/

More information

Exercise 1: RF Stage, Mixer, and IF Filter

Exercise 1: RF Stage, Mixer, and IF Filter SSB Reception Analog Communications Exercise 1: RF Stage, Mixer, and IF Filter EXERCISE OBJECTIVE DISCUSSION On the circuit board, you will set up the SSB transmitter to transmit a 1000 khz SSB signal

More information

MAHALAKSHMI ENGINEERING COLLEGE-TRICHY QUESTION BANK UNIT IV PART-A

MAHALAKSHMI ENGINEERING COLLEGE-TRICHY QUESTION BANK UNIT IV PART-A MAHALAKSHMI ENGINEERING COLLEGE-TRICHY QUESTION BANK SATELLITE COMMUNICATION DEPT./SEM.:ECE/VIII UNIT IV PART-A 1. What are the advantages of the super heterodyne receiver over TRF receiver? (AUC MAY 2004)

More information

Solution of ECE 342 Test 3 S12

Solution of ECE 342 Test 3 S12 Solution of ECE 34 Test 3 S1 1 A random power signal has a mean of three and a standard deviation of five Find its numerical total average signal power Signal Power P = 3 + 5 = 34 A random energy signal

More information

Emona DATEx. Volume 2 Further Experiments in Modern Analog & Digital Telecommunications For NI ELVIS I and II. Barry Duncan

Emona DATEx. Volume 2 Further Experiments in Modern Analog & Digital Telecommunications For NI ELVIS I and II. Barry Duncan Emona DATEx Lab Manual Volume 2 Further Experiments in Modern Analog & Digital Telecommunications For NI ELVIS I and II Barry Duncan . Emona DATEx Lab Manual Volume 2 Further Experiments in Modern Analog

More information

Chapter 14 FSK Demodulator

Chapter 14 FSK Demodulator Chapter 14 FSK Demodulator 14-1 : Curriculum Objectives 1. To understand the operation theory of FSK demodulator. 2. To implement the FSK detector circuit by using PLL. 3. To understand the operation theory

More information

YEDITEPE UNIVERSITY ENGINEERING FACULTY COMMUNICATION SYSTEMS LABORATORY EE 354 COMMUNICATION SYSTEMS

YEDITEPE UNIVERSITY ENGINEERING FACULTY COMMUNICATION SYSTEMS LABORATORY EE 354 COMMUNICATION SYSTEMS YEDITEPE UNIVERSITY ENGINEERING FACULTY COMMUNICATION SYSTEMS LABORATORY EE 354 COMMUNICATION SYSTEMS EXPERIMENT 3: SAMPLING & TIME DIVISION MULTIPLEX (TDM) Objective: Experimental verification of the

More information

Signals and Systems Lecture 9 Communication Systems Frequency-Division Multiplexing and Frequency Modulation (FM)

Signals and Systems Lecture 9 Communication Systems Frequency-Division Multiplexing and Frequency Modulation (FM) Signals and Systems Lecture 9 Communication Systems Frequency-Division Multiplexing and Frequency Modulation (FM) April 11, 2008 Today s Topics 1. Frequency-division multiplexing 2. Frequency modulation

More information

RAO PAHALD SINGH GROUP OF INSTITUTIONS BALANA(MOHINDER GARH)123029

RAO PAHALD SINGH GROUP OF INSTITUTIONS BALANA(MOHINDER GARH)123029 1 COMMUNICATION SYSTEM LAB (EE-226 -F) Communication System Lab (EE-226-F) LAB MANUAL IV SEMESTER RAO PAHALD SINGH GROUP OF INSTITUTIONS BALANA(MOHINDER GARH)123029 Department Of Electronics and Communication

More information

Chapter-15. Communication systems -1 mark Questions

Chapter-15. Communication systems -1 mark Questions Chapter-15 Communication systems -1 mark Questions 1) What are the three main units of a Communication System? 2) What is meant by Bandwidth of transmission? 3) What is a transducer? Give an example. 4)

More information

Angle Modulated Systems

Angle Modulated Systems Angle Modulated Systems Angle of carrier signal is changed in accordance with instantaneous amplitude of modulating signal. Two types Frequency Modulation (FM) Phase Modulation (PM) Use Commercial radio

More information

Experiment No. 3 Pre-Lab Phase Locked Loops and Frequency Modulation

Experiment No. 3 Pre-Lab Phase Locked Loops and Frequency Modulation Experiment No. 3 Pre-Lab Phase Locked Loops and Frequency Modulation The Pre-Labs are informational and although they follow the procedures in the experiment, they are to be completed outside of the laboratory.

More information