SpikerBox v1.3 DIY Instructions

Size: px
Start display at page:

Download "SpikerBox v1.3 DIY Instructions"

Transcription

1 SpikerBox v. DIY Instructions Prepare yourself. In hours, you will have built your own SpikerBox to begin doing neuroscience and whatever your creative mind can conjure. Materials Needed:. A Backyard Brains Bag of Parts. Soldering Iron. Solder. Magnifying Glass to read labels on Chips and Capacitors. 9V battery to power your SpikerBox.. Silly Putty to hold components in place on board while you solder on backside. Pair of scissors. Wire Strippers and Wire Clippers 9. Superglue (gel is best) to glue speaker into enclosure. 0. Electrical Tape A Soldering Iron can be purchased at RadioShack or any local hardware store. The Magnifying Glass and Silly Putty are available at drug stores. SpikerBox Circuit Construction (refer to photograph on next page while building):. Solder Speaker Connector. Install Audio Line Out. Install Power Switch. Install LED (bulb pointing out). Install RCA signal in. Install Chip Holders. The half circle should point toward the front of the board (where input, switch, LED, and line out are).. Install 0 uf capacitor (big one) at C. Grey Stripe needs to point toward connector row (see photo).. Install 0 uf (blue cap) capacitor at C0, C, and C. These have 0 labels in sm all text on them 9. Install 0 kω resistors at R and R (brown black orange). 0. Install 90 Ω resistor at R (near LED) (orange white brown). Install kω resistor at R (near RCA signal in) (orange orange orange). Install kω resistor at R (brown black red) and. Install 0. uf capacitor at C. The capacitor has in small text on it.. Install 0 kω resistor at R (red red yellow).. Install 0 pf capacitor at C. The capacitor has in small text on it.. Install 0.0 uf capacitor at C. The capacitor has in small text on it.. Install 0 Ω resistor at R (brown black black).. Install 0. uf capacitor at C. The capacitor has 0 in small text on it. 9. Install the 9V battery connectors. Take care to ensure the two connectors are flush with each other or else battery will not plug in. The skinny connector (male) goes on the bottom of the board. We recommend soldering with a battery in place.. Install Chips in holders, with circle on all chips pointing towards top of board. AD goes in left holder, LM on right holder, and the TLC goes in the middle holder.. Install battery.

2 Enclosure Construction:. Remove paper backing from the SpikerBox plastic enclosure pieces (or you can leave these on). Place screws in bottom plastic enclosure piece, with screws facing up.. Measure your tubing and cut it into equal parts of 0. inches and parts of 0. inches.. Place 0. inch spacers on top of screws.. Slide your circuit board through the screws on top of the 0. inch spacers, and then put the 0. inch spacers on top of the circuit board through the screws.. Solder Speaker Connector (female) on ends of speaker wire. Take care that the two solder joints do not touch. Separate and wrap solder joints away from each other using electrical tape. Press the speaker into the enclosure, then attach the female end of the cord to the male end of the PCB. If the speaker doesn t fit, you can lightly sand the inner hole until the speaker fits. You can use just a touch of superglue in the inside hole to secure speaker. Be careful superglue smears acrylic very easily.. Slide the top enclosure board on your circuit,, and add the hex nuts to the top of the SpikerBox. Note that the nuts could go either on the top or bottom of the board. There is an internal struggle here at Backyard Brains on which looks better: Nuts up vs. Nuts down. It's your SpikerBox, you decide. 9. Peel and place the cork sticker to the right of the speaker, close to the RCA jack. Electrode Construction:. Unscrew end of RCA connector.. Split and Strip ½ inch lengths from speaker wire on both sides and both ends.. Place wire in eyelets of RCA connector, solder, and crimp where applicable. Take care that connections are both strong and not touching each other.. Rescrew RCA end back on connector.. Solder two sewing needles on other ends of speaker wire. Congratulations! You are done. Turn on your SpikerBox. If your LED comes on and you hear your speaker Click on, your SpikerBox probably works. Now grab your favorite invertebrate and do some experiments. What resistor is what? Resistors have color stripe bands that signify their values. For example, a 0 Ohm resistor is Brown, Black, Black as below: 0 Ω = Brown Black Black 90 Ω = Orange White Brown kω = Brown Black Red 0 kω = Brown Black Orange kω = Orange Orange Orange 0 kω = Red Red Yellow Sometimes you will find an extra silver or gold stripe, but you can ignore those. (They specify the tolerances, %, 0%, etc). For your kit, you will need the following values:

3 BATT BATT BATT R 90 LED SIG 0k 0k R R U AD A B C D E This turns 9V into /.v v 0 = v R 0k =.v I RR 0k0k < To Cockroach Leg Stage Gain gain = 00kΩ = 00kΩ =9v RCA plug R kω =.0x Backyard Brains SpikerBox v..c Dec, 0 REF UA TLC R K x Gain Instrumentation Amp AMP k R C C 0.uF 0.uF C 0.uF R 0k C 0pF TLC HighPass filter Stage Gain Speaker Amp default UB POWER x BandPass Filter Stage AMPA C0 0uF fc = π. r. c fc = π. = Hz x0. 0.0x0 R9 U AMPB 0x Gain Audio Amplifier R Audio Out X X LMN C 0.uF C 0 AMPA R C C 0.0uF 0uF Lowpass Filter SPEAKER AMPB SP Stage GaIn Calculation Speaker Out gain = R/R = 0k/k = 0x fc = π. r. c fc = π. =,9 Hz 0x0. 0x0 0x X But.. In reality it s lower due to roll off: 0 gain Hz frequency Total GaIn Headphone Out = x. x = 9x Speaker = x x 0 =,90x only x at peak,9 Hz A B C D E

4

5

Mono Amplifier. LM386 Headphone Amp

Mono Amplifier. LM386 Headphone Amp Mono Amplifier LM386 Headphone Amp Layout On/Off Switch - cuts power to the circuit Mono Input Jack: use either L or R or solder together Schematic Step 1 - Parts List 1.) R1-10ohm Resistor - Brown Black

More information

Building the Toothpick Audio CW Filter

Building the Toothpick Audio CW Filter Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier

More information

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 3.0 CREATE YOUR OWN SPEAKER DOCK WITH THIS

MONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 3.0 CREATE YOUR OWN SPEAKER DOCK WITH THIS ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 3.0 Build Instructions

More information

Micro USB Lamp Kit TEACHING RESOURCES. Version 2.1 DESIGN A STYLISH LAMP WITH THIS

Micro USB Lamp Kit TEACHING RESOURCES. Version 2.1 DESIGN A STYLISH LAMP WITH THIS TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE DESIGN A STYLISH LAMP WITH THIS Micro USB Lamp Kit Version 2.1 Index of Sheets TEACHING RESOURCES

More information

Pacific Antenna Code Practice Oscillator Kit

Pacific Antenna Code Practice Oscillator Kit Pacific Antenna Code Practice Oscillator Kit This kit is offered to initiate the first time builder in the various techniques of mechanical and electronic kit construction. At the end of the approximately

More information

TV Remote. Discover Engineering. Youth Handouts

TV Remote. Discover Engineering. Youth Handouts Discover Engineering Youth Handouts Electronic Component Guide Component Symbol Notes Amplifier chip 1 8 2 7 3 6 4 5 Capacitor LED The amplifier chip (labeled LM 386) has 8 legs, or pins. Each pin connects

More information

Manual Version July 2007

Manual Version July 2007 Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the

More information

Xylophone Teaching Notes Issue 1.3

Xylophone Teaching Notes Issue 1.3 Teaching Notes Issue 1.3 Product information: www.kitronik.co.uk/quicklinks/2105/ TEACHER Xylophone Index of sheets Introduction Schemes of work Answers The Design Process The Design Brief Investigation

More information

Starving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24

Starving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24 SS2 guide Written By: 6L6 2019 guides.diyaudio.com/ Page 1 of 24 INTRODUCTION This is a build guide for the hybrid headphone/pre-amplifier. You can buy a kit at the SSII product listing on the diyaudio

More information

LDB-1 Kit Instructions Page 1 of 8

LDB-1 Kit Instructions Page 1 of 8 LDB-1 Kit Instructions Page 1 of 8 Important Information Congratulations and thank you for your purchase of the LDB-1 Little Drummer Boy Analog Drum Machine Kit! Before you start, please read the enclosed

More information

Code Practice Oscillator (CPO) For kit building instructions turn to Page 3.

Code Practice Oscillator (CPO) For kit building instructions turn to Page 3. Code Practice Oscillator (CPO) For kit building instructions turn to Page 3. Overview Many thanks for your purchase of this code practice oscillator or CPO, this guide is intended to allow you to quickly

More information

CW-ADD. Universal CW Adapter for SSB Transceivers. Assembly manual. Last updated: October 1,

CW-ADD. Universal CW Adapter for SSB Transceivers. Assembly manual. Last updated: October 1, CW-ADD Universal CW Adapter for SSB Transceivers Assembly manual Last updated: October 1, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for building the Universal CW Adapter kit CW-ADD

More information

Specimen Products Single Ended Stereo Amp Instruction Book

Specimen Products Single Ended Stereo Amp Instruction Book Specimen Products Single Ended Stereo Amp Instruction Book Specimen tube amplifier designs are informed by decades of servicing and building musical instrument amps. As a result of being subjected to the

More information

10 2 2,13,15,16,46 27, non-inductive ,26,

10 2 2,13,15,16,46 27, non-inductive ,26, HANDS-ON RADIO PARTS LIST (Thanks, John AF4WM and Steve AD7KR) Updated through Experiment 129 Quantities assume all parts available for re-use MAX QTY EXPERIMENT NOTES 1/4 WATT RESISTOR (All values are

More information

Main improvements are increased number of LEDs and therefore better temperature indication with one Celsius degree increments.

Main improvements are increased number of LEDs and therefore better temperature indication with one Celsius degree increments. LED Thermometer V2 (Fahrenheit/Celsius/±1 ) PART NO. 2244754 After completing this great starter kit, users will have a nice interactive LED thermometer. You will learn one principle how temperature can

More information

BrewsBySmith.com STC DIY Kit

BrewsBySmith.com STC DIY Kit BrewsBySmith.com STC-1000 + DIY Kit Contact Information: Greg Smith www.brewsbysmith.com greg@boostbysmith.com I. Hardware Included: STC-1000 flashed with latest software (v1.06 currently) (if purchased)

More information

Building the Sawdust Regenerative Receiver

Building the Sawdust Regenerative Receiver Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide

More information

Penrose Quantizer Assembly Guide

Penrose Quantizer Assembly Guide Penrose Quantizer Assembly Guide Schematic and BOM The schematic can be found here: www.sonic-potions.com/public/penrosequantizerschematic.pdf The BOM is available at google docs: Link to BOM Prepare the

More information

Amplifier, Product Design

Amplifier, Product Design Amplifier, Product Design Choose one component from the amplifier circuit and investigate technical, theory and mathematical information related to your chosen component. This work will be completed over

More information

FM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS

FM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Build Instructions Before you start, take

More information

Wiring Manual NEScaf April 2010 (August 2006)

Wiring Manual NEScaf April 2010 (August 2006) Wiring Manual NEScaf April 2010 (August 2006) Switched Capacitor Audio Filter The NEScaf is a switched capacitor audio filter (acronym SCAF) built around a building-block type filter chip. The NEScaf will

More information

Value Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1

Value Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1 Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same

More information

Read This Page First

Read This Page First Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly

More information

S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions

S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions First, make sure you have all the required components: HARDWARE Qty Item 1 DSKY PCB v1.0d 1 Arduino Nano 1 VA RTC 1 IMU 1 Buck StepDown 1 SKM53

More information

Building the Sawdust Regenerative Receiver

Building the Sawdust Regenerative Receiver Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide

More information

Lesson 2: Soldering. Goals

Lesson 2: Soldering. Goals Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit

More information

Model 333 Single Channel USB Chromatography Data System Relay ( Contact Closure ) Installation

Model 333 Single Channel USB Chromatography Data System Relay ( Contact Closure ) Installation Remove the four screws holding the Model 333 A/D board in the stand-alone box. If the 333 is installed in a GC or HPLC, remove the four hex head screws from the outside of the instrument which secure the

More information

INSPIRE VLF-3 Rev #1C Receiver Kit ASSEMBLY INSTRUCTIONS

INSPIRE VLF-3 Rev #1C Receiver Kit ASSEMBLY INSTRUCTIONS INSPIRE VLF-3 Rev #1C Receiver Kit ASSEMBLY INSTRUCTIONS The following assembly instructions should be followed carefully. The INSPIRE VLF-3 receiver kit is NOT a simple electronic assembly. If you follow

More information

Welcome to the DIY Thirsty Plant Kit - Manual

Welcome to the DIY Thirsty Plant Kit - Manual Welcome to the DIY Thirsty Plant Kit - Manual This is a step-by-step guide to making your own Thirsty Plant Detector. The equipment you should have at your station are wire strippers, wire cutters, wooden

More information

Elektor Construction Guide TAPIR

Elektor Construction Guide TAPIR Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1

More information

Programmable Timer Teaching Notes Issue 1.2

Programmable Timer Teaching Notes Issue 1.2 Teaching Notes Issue 1.2 Product information: www.kitronik.co.uk/quicklinks/2121/ TEACHER Programmable Timer Index of sheets Introduction Schemes of work Answers The Design Process The Design Brief Investigation

More information

Guitarpedalkits.com Overdrive Pedal Build Instructions

Guitarpedalkits.com Overdrive Pedal Build Instructions Page 1 Guitarpedalkits.com Overdrive Pedal Build Instructions Follow the instructions in this guide to build your very own DIY overdrive pedal from GuitarPedalKits.com. If you re a first time builder,

More information

DELUXE STEREO AMPLIFIER KIT

DELUXE STEREO AMPLIFIER KIT TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE CREATE YOUR OWN SPEAKER DOCK WITH THIS DELUXE STEREO AMPLIFIER KIT Version 2.0 Index of Sheets TEACHING

More information

DARK ACTIVATED COLOUR CHANGING NIGHT LIGHT KIT

DARK ACTIVATED COLOUR CHANGING NIGHT LIGHT KIT TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE CREATE SOOTHING LIGHTING EFFECTS WITH THIS DARK ACTIVATED COLOUR CHANGING NIGHT LIGHT KIT Version

More information

Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit!

Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping

More information

EASY BUILD TIMER KIT TEACHING RESOURCES. Version 2.0 LEARN ABOUT SIMPLE TIMING CIRCUITS WITH THIS

EASY BUILD TIMER KIT TEACHING RESOURCES. Version 2.0 LEARN ABOUT SIMPLE TIMING CIRCUITS WITH THIS TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE LEARN ABOUT SIMPLE TIMING CIRCUITS WITH THIS EASY BUILD TIMER KIT Version 2.0 Index of Sheets TEACHING

More information

& ' (wire, inches) 16 black Tef-Flex 16 Black Lex 32 Red Lex 48 Blue Tef-Flex 32 White Tef-Flex

& ' (wire, inches) 16 black Tef-Flex 16 Black Lex 32 Red Lex 48 Blue Tef-Flex 32 White Tef-Flex ! " # $! " % Qty Part (woofer) 1 4.40mH 16 AWG inductor 1 10.0uF Yellow film capacitor 1 5.62 Ohm NORTH resistor (tweeter) 1 8uF Yellow film capacitor 1 0.56mH 16 AWG inductor 1 3.32 Ohm NORTH resistor

More information

Pacific Antenna Easy TR Switch

Pacific Antenna Easy TR Switch Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver

More information

_ o -+- o. ) \/\/(_) <_\ (_)

_ o -+- o. ) \/\/(_) <_\ (_) _ o _ (_ _> _> _> _ o -+- o _ (_) _(/_ (/_ (/_ (_ (/._ _ ) \/\/(_)

More information

3. Assembly manual ANALYZING THE PCB'S LCD PCB. Component side: Solder side:

3. Assembly manual ANALYZING THE PCB'S LCD PCB. Component side: Solder side: 3. Assembly manual ANALYZING THE PCB'S LCD PCB Component side: Solder side: MAIN PCB Component side: Solder side: ASSEMBLGING THE LCD PCB 1. Resistor R1: 33 Ohm (orange, black, black) 2. 6 Pin female header

More information

Value Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1

Value Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1 P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!

More information

Patton Robotics, LLC.

Patton Robotics, LLC. Patton Robotics LLC Patton Robotics T3 Motherboard Assembly Instructions Version 1.1 Patton Robotics, LLC. 61 Hagan Drive New Hope, PA 18938 Phone: 609-977-5525 Email: pattonrobotics@gmail.com Copyright

More information

Firefly Jar Learn to Solder Kit

Firefly Jar Learn to Solder Kit Firefly Jar Learn to Solder Kit Parts Tools A. Firefly Jar PCB B. 10mm Flickering LED (White or Yellow) C. Resistor D. Tilt Switch (Black or Green) E. Battery Holder F. Velcro ( Not Pictured) G. Jar (

More information

Pacific Antenna - Easy TR Switch

Pacific Antenna - Easy TR Switch Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair

More information

STEADY HAND GAME WITH LATCHING LED

STEADY HAND GAME WITH LATCHING LED ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS TEST YOUR HAND-EYE COORDINATION WITH THIS STEADY HAND GAME WITH LATCHING LED Version 2.0

More information

TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT. Version 2.

TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT. Version 2. TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT Version 2.2 Index of Sheets TEACHING RESOURCES Index of Sheets

More information

DC Motor. Controller. User Guide V0210

DC Motor. Controller. User Guide V0210 DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,

More information

The Walford Electronics Ford Receiver Kit Project Construction Manual

The Walford Electronics Ford Receiver Kit Project Construction Manual The Walford Electronics Ford Receiver Kit Project Construction Manual Walford Electronics Ford Receiver construction manual V1.5 Page 1 of 22 Introduction The Ford receiver has four stages: The first stage

More information

4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com

4ms SCM Breakout. Kit Builder's Guide for PCB v2.1 4mspedals.com 4ms SCM Breakout Kit Builder's Guide for PCB v2.1 4mspedals.com Shuffling Clock Multiplier Breakout This guide is for building a Shuffling Clock Multiplier Breakout module (SCMBO) version 2.1 from the

More information

ABC V1.0 ASSEMBLY IMPORTANT!

ABC V1.0 ASSEMBLY IMPORTANT! ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through

More information

Assembly and Installation Instructions for White Oak Audio Design PL400 Series 1 LED board

Assembly and Installation Instructions for White Oak Audio Design PL400 Series 1 LED board Thank you for purchasing White Oak Audio Design s Phase Linear PL400 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with

More information

Lighthouse Beginner s soldering kit

Lighthouse Beginner s soldering kit Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1

More information

Cricket 80a Assembly Manual v Copyright David Cripe NM0S The 4 State QRP Group

Cricket 80a Assembly Manual v Copyright David Cripe NM0S The 4 State QRP Group Cricket 80a Assembly Manual v. 1.0 Copyright 2017 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a CRICKET 80a Transceiver. We hope you will enjoy building it and find it

More information

Assembly Instructions

Assembly Instructions Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with

More information

SoftRock v6.0 Builder s Notes. May 22, 2006

SoftRock v6.0 Builder s Notes. May 22, 2006 SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),

More information

MICROGRANNY v2.1 - Assembly Guide

MICROGRANNY v2.1 - Assembly Guide last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl

More information

PAT-4 POWER SUPPLY ASSEMBLY MANUAL Rev B Version

PAT-4 POWER SUPPLY ASSEMBLY MANUAL Rev B Version PAT-4 POWER SUPPLY ASSEMBLY MANUAL Rev B Version 2013 AkitikA, LLC All rights reserved Revision Bp01 November 3, 2013 Page 1 of 16 Table of Contents Table of Contents... 2 Table of Figures... 2 Section

More information

THE RING RESONATOR (K-975)

THE RING RESONATOR (K-975) THE RING RESONATOR (K-975) OUTPUT BOOST The Ring Resonator An Octave Up Fuzz Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery life. Use these instructions

More information

THE STEP LADDER (K-978)

THE STEP LADDER (K-978) THE STEP LADDER (K-978) Footswitch True-bypass = 0 db OUTPUT INPUT Ground shunt switching on the input jack keeps the amp quiet when unplugged from the Step Ladder. Attenuator Pot Full clockwise = 0 db

More information

Raygun. Vector Weapon. projects. Raygun vector weapon. Build a mini analog sound-effects circuit. By Symetricolour. Time: 2 4 hours CosT: $15 $20

Raygun. Vector Weapon. projects. Raygun vector weapon. Build a mini analog sound-effects circuit. By Symetricolour. Time: 2 4 hours CosT: $15 $20 projects Raygun vector weapon Raygun Vector Weapon By Symetricolour Time: 2 4 hours CosT: $5 $20 Build a mini analog sound-effects circuit. Gregory Hayes 02 Materials» raygun Vector Weapon Kit item #MSVWP

More information

PB 700 PB 1000 PB 1100 PB 1500 PB 2600 PB 1200 PB 1700 PB 2200 PB 2700 USER'S MANUAL.

PB 700 PB 1000 PB 1100 PB 1500 PB 2600 PB 1200 PB 1700 PB 2200 PB 2700 USER'S MANUAL. PB 700 PB 1000 PB 1100 PB 1500 PB 2600 PB 1200 PB 1700 PB 2200 PB 2700 USER'S MANUAL www.pyramidcaraudio.com congratulations... on your purchase of a Pyramid America Series amplifier. This amplifier extends

More information

Time of Arrival Radio Direction Finder.

Time of Arrival Radio Direction Finder. Time of Arrival Radio Direction Finder. Time of arrival (TOA) RDF units are simple and very useful. Various designs have been distributed over the years, and here is another one. This Kit Developed by

More information

KASTLE v1.5 - Assembly Guide

KASTLE v1.5 - Assembly Guide last update: 14. 12. 2017 KASTLE v1.5 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the Kastle kit - mini modular synthesizer. It is suitable for beginners. It is

More information

Bill of Materials: Metronome Kit PART NO

Bill of Materials: Metronome Kit PART NO Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different

More information

N3ZI Kits General Coverage Receiver, Assembly & Operations Manual (For Jun 2011 PCB ) Version 3.33, Jan 2012

N3ZI Kits General Coverage Receiver, Assembly & Operations Manual (For Jun 2011 PCB ) Version 3.33, Jan 2012 N3ZI Kits General Coverage Receiver, Assembly & Operations Manual (For Jun 2011 PCB ) Version 3.33, Jan 2012 Thank you for purchasing my general coverage receiver kit. You can use the photo above as a

More information

DRTXM2 TRANSMITTER BILL OF MATERIAL IDENT QTY PART NUMBER DESCRIPTION

DRTXM2 TRANSMITTER BILL OF MATERIAL IDENT QTY PART NUMBER DESCRIPTION DRTXM2 TRANSMITTER BILL OF MATERIAL H1 C1-5,7,10-11,15,17-18,20, 22-28,34,38, 43-46,49-53,1A,2A 8 Right Angle LED Mount 0 0.01uf 50V Ceramic Disc Capacitor 31 0.1 UF/50V Decoupling Capacitors C13,14,39-42

More information

Build Your Own Clone Chancellor Kit Instructions

Build Your Own Clone Chancellor Kit Instructions Build Your Own Clone Chancellor Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.

More information

Line Following Circuit Board Wiring Guide

Line Following Circuit Board Wiring Guide Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove

More information

DIY-990. assembly guide. Hairball Audio, LLC V3.0

DIY-990. assembly guide. Hairball Audio, LLC V3.0 DIY-990 V3.0 assembly guide Hairball Audio, LLC Saftey Precausions Read and understand all of the instructions before assembling this DIY project. Improper assembly could result in damage to your property

More information

The Useless Machine. Parts Only - Build Guide v0001

The Useless Machine. Parts Only - Build Guide v0001 TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,

More information

SoftRock v6.0 Builder s Notes. April 6, 2006

SoftRock v6.0 Builder s Notes. April 6, 2006 SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),

More information

The Useless Machine. DIY Soldering Edition. Instruction Guide v0004

The Useless Machine. DIY Soldering Edition. Instruction Guide v0004 The Useless Machine DIY Soldering Edition Instruction Guide v0004 TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: Soldering

More information

DeluxeArcade. JAMMA Fingerboard. Introduction. Features. Version 1.1, November 2014 Martin-Jones Technology Ltd

DeluxeArcade. JAMMA Fingerboard. Introduction. Features. Version 1.1, November 2014 Martin-Jones Technology Ltd DeluxeArcade JAMMA Fingerboard Version., November 204 Martin-Jones Technology Ltd http://www.martin-jones.com/ Introduction The Deluxe Arcade JAMMA Fingerboard is designed to make adapting non-jamma arcade

More information

IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015

IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The

More information

Never power this piano with anything other than a standard 9V battery!

Never power this piano with anything other than a standard 9V battery! Welcome to the exciting world of Digital Electronics! Who is this kit intended for? This kit is intended for anyone from ages 13 and above and assumes no previous knowledge in the field of hobby electronics.

More information

ASSEMBLY and OPERATION MANUAL

ASSEMBLY and OPERATION MANUAL ASSEMBLY and OPERATION MANUAL TTL NIXIE Digital Clock Rev. 2 January 19, 2011 TABLE OF CONTENTS Introduction 3 Design Objective 3 Theory of Operation 3 Assembly tips 4 Required tools 4 Inspection 4 Before

More information

Minty Amp assembly instructions

Minty Amp assembly instructions Minty Amp assembly instructions Parts Required: LM386 OpAmp (included in kit) 2x 100uf (min 16v) Electrolytic Capacitors (included in kit) 0.1uf Ceramic Capacitor (included in kit) 0.047uf Ceramic Capacitor

More information

OpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV

OpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering

More information

16 Bit Micro Experimenter Assembly and Check out Instructions

16 Bit Micro Experimenter Assembly and Check out Instructions 16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly

More information

LITTLE NERD v1.1 Assembly Guide

LITTLE NERD v1.1 Assembly Guide last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills

More information

VOLUME AND TONE CONTROL - PREAMPLIFIER K8084

VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control H8084IP-1 Features & specifications When

More information

Assembly Instructions for the 1.5 Watt Amplifier Kit

Assembly Instructions for the 1.5 Watt Amplifier Kit Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are

More information

Tutorial Building the Mono Amp Case

Tutorial   Building the Mono Amp Case Kitronik Ltd Building the Mono Amp Case Tools you will need: Wire cutters/strippers A soldering iron A small cross headed screwdriver A pair of pliers A ruler Included with your case you should find: 16

More information

Bill of Materials: General Purpose Alarm, Pulsed PART NO

Bill of Materials: General Purpose Alarm, Pulsed PART NO General Purpose Alarm, Pulsed PART NO. 2190207 I hate alarms that sound continuously - unless they are smoke alarms. Smoke alarms should be annoying, but others should not. I wanted an alarm for a function

More information

How to build a Cracklebox. Red Wierenga Brooklyn College Center for Computer Music October 13, 2015

How to build a Cracklebox. Red Wierenga Brooklyn College Center for Computer Music October 13, 2015 How to build a Cracklebox Red Wierenga Brooklyn College Center for Computer Music October 13, 2015 What s a Cracklebox? What s a Cracklebox? The Cracklebox was developed by Michel Waisvisz and others at

More information

Stereo 3.7W Class D Audio Amplifier

Stereo 3.7W Class D Audio Amplifier Stereo 3.7W Class D Audio Amplifier Created by Bill Earl Last updated on 2014-10-28 10:45:16 AM EDT Guide Contents Guide Contents Overview Specifications: What is a Class D Amplifier? Other Audio amps

More information

CALF Configurable Audio Limiter Filter

CALF Configurable Audio Limiter Filter CALF Configurable Audio Limiter Filter CALF Parts List Package Contents PCB Calf Front Panel PCB CALF Main Board Enclosure w/ Panels Components Front Panel Components Chassis Components Power Supply Components

More information

EE43 43/100 Fall Final Project: 1: Audio Amplifier, Part Part II II. Part 2: Audio Amplifier. Lab Guide

EE43 43/100 Fall Final Project: 1: Audio Amplifier, Part Part II II. Part 2: Audio Amplifier. Lab Guide EE 3/00 EE FINAL PROJECT PROJECT:AN : AUDIO AUDIO AMPLIFIER AMPLIFIER Part : Audio Amplifier Lab Guide In this lab we re going to extend what you did last time. We re going to use your AC to DC converter

More information

Intellivision A/V Mod Installation Guide

Intellivision A/V Mod Installation Guide Intellivision A/V Mod Installation Guide This document will guide you through installing your Intellivision A/V Mod Kit to your Intellivision I, II, and III game consoles. Installation is basically the

More information

QRPGuys Michigan Mighty Might Plus 40M Transmitter

QRPGuys Michigan Mighty Might Plus 40M Transmitter QRPGuys Michigan Mighty Might Plus 40M Transmitter First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use

More information

SoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit

SoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),

More information

Circuit Board Assembly Instructions for Babuinobot 1.0

Circuit Board Assembly Instructions for Babuinobot 1.0 Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming

More information

IPR LA-3 KIT last update 15 march 06

IPR LA-3 KIT last update 15 march 06 IPR LA-3 KIT last update 15 march 06 PART-2: Audio Circuitry CIRCUIT BOARD LAYOUT: Power and Ground Distribution Now that your power supply is functional, it s time to think about how that power will be

More information

Build this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ

Build this Direct Digital Synthesizer Development Kit By: Diz Gentzow, W8DIZ Build this Direct Digital Synthesizer "Development Kit" By: Diz Gentzow, W8DIZ A great tutorial for adding a keypad to the DDS Kit by Bruce, W8BH This manual has been prepared to be read directly on screen.

More information

Read This Page First

Read This Page First Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions contact qrpkits.com@gmail.com There is no need to print out the whole assembly

More information

SSB-MITE Assembly Manual. Copyright David Cripe NM0S The 4 State QRP Group. Introduction

SSB-MITE Assembly Manual. Copyright David Cripe NM0S The 4 State QRP Group. Introduction SSB-MITE Assembly Manual Copyright 2017 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a SSB-MITE. We hope you will enjoy building it and find it a useful addition to your

More information

STEP 0 Prepare the Materials.

STEP 0 Prepare the Materials. How to Build a Germanium Fuzz Guitar Effect. This document will guide you to build and test your Germanium Fuzz guitar pedal. With all the materials on hand, it takes around 2-4 hours to build it. Try

More information

Assembly and Installation Instructions for White Oak Audio Design TM-1001 LED board

Assembly and Installation Instructions for White Oak Audio Design TM-1001 LED board Thank you for purchasing White Oak Audio Design s TM-1001 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with your tuner.

More information

Materials. Eight pin DIP socket 0.1 µf capacitor

Materials. Eight pin DIP socket 0.1 µf capacitor JOE GROELE Project Outline The goal of this project was to build a plasma speaker that will amplify an electric guitar sound. Build an audio oscillator circuit using an ordinary speaker Test speaker performance

More information

The Wave (K-MOD103) GUITAR DWELL REVERB REVERB SWITCH ON OUT OFF

The Wave (K-MOD103) GUITAR DWELL REVERB REVERB SWITCH ON OUT OFF The Wave (K-MOD103) OUT IN GUITAR IN DWELL REVERB REVERB SWITCH ON GUITAR OUT POWER ON OFF OFF Please note, there are no labels for this kit. The controls, switches and connectors have only been labeled

More information