Comparative Analysis of Rectangular Microstrip Patch Array Antenna with Different Feeding Techniques

Transcription

1 , pp Comparative Analysis of Rectangular Microstrip Patch Array Antenna with Different Feeding Techniques K. Srinivasa Naik 1, S. Aruna 2, Karri.Y.K.G.R.Srinivasu 1 and Darimisetti Sai Kiran 1 1 Department of Electronics and Communication Engineering 1 Vignan s Institute of Information and Technology, Visakhapatnam, A.P, India nivas @gmail.com 2 Department of Electronics and Communication Engineering 2, 2 Andhra University, Visakhapatnam, A.P, India aruna @gmail.com Abstract. Wireless communication system plays a prominent role in many applications like long distance communication, mobile applications, high performance aircraft, missile applications. For this purpose wireless communication systems requires antenna with compact, flexible, ease of installation, high gain and directivity. Rectangular single element microstrip patch antenna used in many applications, but these are not suitable for satellite communications, space crafts, high resolution Radars because they need enhanced gain and also directivity. In view of the above facts to enhance the gain and directivity and low beam width by increasing the number of patch elements with series, parallel and individual feed network at an operating frequency of 10GHz with dielectric constant 2.2. The 4 element and 8 element design has carried out in this work by comparing with single element. Some of the system operational characteristics depend on directional properties of antenna. HFSS software is a tool for this project design and implementation. Antenna primary parameters such as impedance band width, directivity, gain, radiation pattern, beam width were compared among all three types of feed network. Keywords: Wireless communication; Rectangular micro strip patch antenna; Beam width; Gain; Directivity; Operating frequency; HFSS (High Frequency Structure Simulator). 1 Introduction A simple conducting element which provides impedance matching between source to load can act as an antenna. The morphological changes applied to conducting elements can turn into an antenna and it must also satisfy both maximum power transfer theorem and reciprocity theorem is well. Though the antennas are extensively used in communications they must be capable of radiating the energy to longer distance. Hence a flared structure is incorporated to the antenna [1-2]. To find the distance of the ships and to navigate at sea shore, the ships are subjected to roll and pitch in marine radar applications. The sum patterns which are ISSN: ASTL Copyright 2017 SERSC

2 observed in the ships are very useful in wireless communication and in high resolution radar applications [3-5]. 2 Microstrip Patch Antenna Microstrip patch antennas have advantages like low size, high performance, low cost, low profile antenna. With the increase in the advancement of science and technology the usage of microstrip patch antenna has been increased because of their low structural characteristics [6]. For accurate and high efficiency system design requires a lossless substrate material and substrate height. Here in this pursuit ROGERS RT-DUROID is a lossless substrate material with dielectric constant value of 2.2 [7]. Generally, we have different types of micro strip patch antennas like rectangular, circular, square, triangular, disk sector and many more but out of this rectangular micro strip patch antenna having essential characteristics, low cost, ease to design. The general design of microstrip patch antenna shown in figure 1. Fig. 1. Rectangular Microstrip Patch Antenna To provide better efficiency and larger bandwidth. Microstrip patch antennas constitutes of a narrow conducting strip whose thickness is very negotiable when compared to its operating wavelength (t<<λ 0), the height of the patch is usually dependent on the material (h << λ 0, usually 0.003λ 0 h 0.05λ 0) which is separated by a fraction of λ 0 above the conducting plane. The length L of the element is usually λ 0/3 < L < λ 0/2 for a rectangular patch [8]. 136 Copyright 2017 SERSC

3 3 Design Equations f r 2L 1 reff 0 0 (1) reff (2) W r 1 2 r 1 r 1 h (3) W 1 L 2 L (4) f 2 r reff o o 4 Design of the Models The dimensions of the single element patch antenna are follows, Length of the patch 0.9cm, width of the patch 1.19cm, inset feed length 0.295cm, feed width of 0.243cm are calculated by using above mentioned transmission line model equations. The same units of the single element microstrip patch antenna are also used in designing four element microstrip patch antenna with series feed. The separation gap between two patches is λ/2. The feeding port always exists at the extreme end patch out of 4 elements. All the 4 elements are interconnected with a narrow feed line [9]. The 8 element design of patch array antenna network is also utilizing the dimensions of the one element antenna. Upon the substrate all the 8 elements were placed serially and the feeding is provided to the last element in the array. The space consumption of the 8 element array is more when compared to the 4 element and single element antenna. All the patch elements are separated by a gap of λ/2 and the lumped port excitation has been given using 50ohm feed line. The Four element and Eight element rectangular microstrip patch Antenna are excited with Series Feed, Parallel Feed and Individual Feed Networks. Fig. 2. Single Element Rectangular Microstrip Patch Antenna Copyright 2017 SERSC 137

4 Fig. 3. Four Element Rectangular Microstrip Patch Array Antenna with Series Feed Fig. 4. Four Element Rectangular Microstrip Patch Array Antenna with Parallel Feed 5 Results The following section gives result analysis of all the above mentioned designs are shown below with their plots. 138 Copyright 2017 SERSC

5 Copyright 2017 SERSC 139

6 Table 1. Comparison Between All Different RMPA Antennas Number of Patch Elements in the Antenna Comparison Between Parameters Return Loss Gain Directivity Beam Width Four element series feed design -22.7dB 11.9dB db 40 0 Eight element series feed design dB 13.2dB 13.3 db 34 0 Two element parallel feed design dB 10.18dB db 36 0 Four element parallel feed design dB 13.02dB db 17 0 Eight Element parallel feed design dB 16.46dB db 9 0 Two element individual feed design dB 10.60dB db 40 0 Four element individual feed design dB 13.60dB db 20 0 Eight element individual feed design dB 16.59dB db 11 0 From the above tabular data, there are few conclusions that can be made, by which the performance analysis of the RMPA antenna can be illustrated. The maximum gain that can be attained is 16.59dB for an eight element patch array with individual feed. 140 Copyright 2017 SERSC

7 6 Conclusion The designed array antennas are centered at frequency around 10GHz can be adopted into Radar applications because of its low beam width. Return loss value increases when the antenna feeds in a serial way, and coming to parallel feed mechanism, there is a fluctuation of return loss value due to the number of elements. Whereas in individual feed, the variation in the return loss also increases but it is negotiable. Irrespective of whether an antenna is in series, parallel or individual feed, if the number of patch elements increases, the Gain and Directivity value increases whereas beam width decreases. Hence it can be concluded that when compared to all three types of feeding methods, individual feed technique offers better results in terms of Gain and Directivity. References 1. Kraus, John D. "Antennas." (1988). 2. Raju, G. S. N. Antennas and wave propagation. Pearson Education India, Pozar, David M. "Microstrip antenna aperture-coupled to a microstripline." Electronics letters 21 (1985): Naik, K. Srinivasa, and S. Aruna. "Investigations on the generation of patterns for marine radar applications." Indian Journal of Science and Technology 9, no. 7 (2016). 5. Naik, K. Srinivasa, and G. S. N. Raju. "Studies on Difference patterns from Cosecant patterns." IOSR-JECE 9, no. 6 (2014): Balanis, Constantine A. Antenna theory: analysis and design. John Wiley & Sons, Skolnik, Merrill Ivan. "Radar handbook." (1970). 8. Marrocco, Gaetano. "The art of UHF RFID antenna design: impedance-matching and sizereduction techniques." IEEE antennas and propagation magazine 50, no. 1 (2008): Ab Wahab, Norfishah, Zulkifli Bin Maslan, Wan Norsyafizan W. Muhamad, and Norhayati Hamzah. "Microstrip rectangular 4x1 patch array antenna at 2.5 GHz for WiMax application." In Computational Intelligence, Communication Systems and Networks (CICSyN), 2010 Second International Conference on, pp IEEE, Garg, Ramesh. Microstrip antenna design handbook. Artech house, Carver, Keith, and James Mink. "Microstrip antenna technology." IEEE transactions on antennas and propagation 29, no. 1 (1981): Mak, C. L., K. M. Luk, K. F. Lee, and Y. L. Chow. "Experimental study of a microstrip patch antenna with an L-shaped probe." IEEE Transactions on Antennas and Propagation 48, no. 5 (2000): Kumar, Girish, and K. P. Ray. Broadband microstrip antennas. Artech House, Copyright 2017 SERSC 141