AMP NETCONNECT Category 6 System

Size: px
Start display at page:

Download "AMP NETCONNECT Category 6 System"

Transcription

1 AMP NETCONNECT Category 6 System

2 2 How Did We Get Here? Basic Cabling Structure Component Specifications Link/Channel Specifications Additional Structure Options EIA/TIA TSB36 EIA/TIA 568 TIA/EIA TSB40 TIA/EIA TSB72 TIA/EIA TSB67 IEC TIA/EIA TSB75 TIA/EIA 568-A Patch Cord E DIN Prop Delay, Skew Enhanced Addendum Additional Cat 5 Specs ISO/IEC CAT 6 &7 Specs

3 Data Rate = Bandwidth 100 MHz Is Not 100 Mbps! 3 Bandwidth is... A specified frequency range for components and systems Not based on application or data rate 1 MHz to 100 MHz per Cat 5 specifications 1 MHz to 250 MHz per Cat 6 specifications Limited by usable ACR (not data rate) Data rate is... Data speed at a given bandwidth Dependent on the application and encoding scheme

4 Data Rate = Bandwidth Encoding Schemes 4 V 0 V 0 +V Binary Bit Stream NRZI 1 cycle (1 Hz) = 2 bits 1 cycle (1Hz) = 4 bits MLT-3 -V

5 5 Data Rate and Signal Bandwidth Network Cable Pairs Full Duplex Line Code Min. Signal Bandwidth Coding Levels Cabling Category 10BASE-T 2 No Manch -ester 100VG- AnyLAN 10 MHz No NRZ 12.5 MHz BASE-Tx 2 No MLT MHz Mbps ATM 2 Yes NRZ 77.5 MHz BASE-T 4 Yes TX/T MHz 5 5?

6 6 Cat 5 - Where It All Started TSB 67-10/95 1st Definition of field test requirements 3 Years after definition of Cat 5 components Defines link and channel Defines test parameters Wire map Length Attenuation NEXT Defines requirements for test equipment

7 7 Performance Characteristics Key Performance Parameters Near End Crosstalk (NEXT) Attenuation Attenuation to Crosstalk Ratio (ACR) Pair 1 XCVR Pair 2 XCVR NIC HUB

8 8 NEXT, Attenuation and ACR NIC Transmitter Coupled NEXT Noise HUB Receiver Receiver Attenuated Signal Transmitter Transmitted Signal ACR Attenuated Signal NEXT Noise

9 9 The Move to Cat 5e June IEEE begins work on Gigabit Ethernet Questions raised about unspecified parameters of Category 5 Also need to standardize manufacturers claims of performance in excess of Cat 5

10 Addendum September TIA/EIA-568-A-1: Propagation delay and skew requirements added for Cat 5 cable.

11 Specifications Effects of Skew 1 1 T1 T2 Fastest Pair 1 Pair 2 Pair 3 NIC Pair 4 Slowest HUB Skew is the difference in propagation delay between the fastest and slowest pairs in a cable. Proposed requirement: < MHz (Channel)

12 1 2 Two More Addenda Drafted SP-4194 Proposed Addendum No. 4 to 568-A Additional Transmission Performance Specifications for 4-Pair 100 Ohm Category 5 Cabling SP-4195 Proposed Addendum No. 5 to 568-A Additional Transmission Performance Specifications for 4-Pair 100 Ohm Enhanced Category 5 Cabling

13 1 3 Addendum vs. TSB The TIA changed its position on SP-4194 Can t place new specifications on existing components and installations Information has been published as TSB 95 Informational purposes Changes from shall to probably!

14 TSB95 - Additional Cat 5 Specifications 1 4 The development of certain high-speed applications has brought to the attention of the TIA the need for additional transmission requirements such as return loss and far end crosstalk (FEXT). These parameters are needed by system designers for applications that utilize all four pairs in the cable for full duplex transmission. Although these are new specifications, the existing worst-case, two-connector topologies compliant with TIA/EIA-568-A are expected to meet these requirements. Other topologies are supported as long as they meet the ELFEXT and Return Loss requirements of this document.

15 Two-connector Topologies? 1 5 Other Topologies... (i.e. with cross-connect and/or transition point)

16 1 6 New Performance Specifications Additional performance parameters for 4-pair systems Power Sum NEXT Power Sum ELFEXT Return Loss Skew Pair Mbps Pair 2 Pair Mbps Pair 4 NIC HUB

17 Performance Characteristics NEXT: Pair-to-Pair vs. Power Sum 1 7 Pair-to-pair: Single disturber Single receiver Power sum: Multiple disturbers Single receiver Power sum performance is the sum of the pair-to-pair performance of the component or system.

18 1000BASE-T Noise Sources Mb/s Full Duplex 1000 Mb/s PS NEXT PS FEXT 1000 Mb/s NIC EMI Return Loss HUB NEXT - Cancelable by DSP Return Loss- Cancelable by DSP FEXT - Non-Cancelable by DSP EMI - Non-cancelable by DSP

19 SP Enhanced Cat The development of certain high-speed applications has brought to the attention of the TIA the need for additional transmission requirements such as multi-disturber NEXT, return loss and multi-disturber far end crosstalk (FEXT). These parameters are needed by system designers for applications that utilize all four pairs in the cable for simultaneous bi-directional transmission. Addendum 5 for category 5e cabling provides higher performance over a minimally compliant category 5 channel and recognizes advances in cabling technology.

20 Cat 5 Comparisons 2 0 Original Cat 5 Current Cat 5 Cat 5e Attenuation Same Same (components, link, channel) NEXT (components, Same Better link, channel) Skew (link, channel) Same Return Loss (cable, Better link, channel) ELFEXT (cable, link, Better channel) PSELFEXT (link, channel) Better PSNEXT (cable, link, channel) FEXT (connector)

21 Cat 5 vs. Cat 5e 2 1 db Cat 5 ACR Cat 5e ACR Frequency, MHz Attenuation Cat 5 NEXT Cat 5e NEXT Cat 5e PSNEXT

22 What Do You NEED to Run 1000BASE-T? 2 2 IEEE 802.3ab Physical layer specification for 1000 Mb/s operation on four pairs of Category 5 or better balanced twisted pair cable (1000BASE-T) 40.8 Link Segment Characteristics 1000BASE-T uses a duplex transmission system. Four full duplex channels are required to transport data between two PMDs. Each duplex channel supports an effective data rate of 250 Mbps in each direction simultaneously. The term link segment used in this clause refers to four duplex channels and the term duplex channel will be used to refer a single channel with full duplex capability. Specifications for a link segment applies equally to each for the four duplex channels. 1000BASE-T is designed to operate over a 4-pair Category 5 cabling system.

23 Designed to Operate Over Cat 5, BUT ANNEX 40A Additional Cabling Design Guidelines Although the 1 Gb/s specification described in Clause 40 was designed to operate over 4- pair Category 5 cabling systems as specified in ANSI/TIA/EIA-568-A and ISO/IEC 11801, there are additional steps that may be taken by network designers that will provide additional operating margins and ensure the objective BER of is achieved. Power Sum NEXT Defined but not spec d higher than Cat 5 Power Sum ELFEXT Spec d in TSB95 (Cat 5) Don t use 25-pair Don t use crossconnect or transition point

24 2 4 Cat 5 and Cat 5e Bottom Line Cat 5 will probably run Gigabit Ethernet. But maybe only with two connectors! Cat 5e provides the extra margin required to ensure 1000BASE-T support with 4-connector channels. It s been ratified as TIA/EIA-568-A-5. Cat 5 is not recommended in TIA/EIA-568-B. It s been relegated to an annex. Cat 5e is the minimum recommendation for data cabling.

25 2 5 What About Category 6? Cat 6 was originally a German DIN standard addressing shielded cabling systems with performance out to 600 MHz. Category 6/Class E was re-proposed by ISO/IEC A as specifying positive channel performance to 250 MHz. Both the ISO and the TIA are now working on Cat 6 and its frequency range has been extended to 250 MHz. The German DIN Cat 6 is now Cat 7/Class F, also under development by the ISO.

26 Cat 5e vs. Cat Cat 5e ACR Cat 6 ACR Cat 5e Attn Cat 6 Attn Cat 5e NEXT Cat 6 NEXT

27 Chicken and Egg Which Came First? 2 7 LAN Standards ATM Forum IEEE Cabling Trends Power Sum Category 6 LAN Technologies 622 Mbps ATM Gigabit Ethernet Cabling Standards Enhanced Cat 5 Cat 6/Class E

28 2 8 Why Install Category 6? Performance Level: 250 MHz Applications: All existing UTP applications including 1000BASE-T Forms the basis on which the next generation of twisted pair applications will be developed 25-Year System Warranty: Category 6

29 2 9 The AMP NETCONNECT Category 6 System Category 6 performance confirmed by independent testing Intertek Testing Services (ETL SEMKO) End-to-end system engineering ensures optimum performance Critical at 250 MHz Category 6 bandwidth Look at the system performance - not just cable Single vendor solution and warranty No shifting partnerships

30 3 0 Category 6 Cable Performance superior to Category 6 requirements Designed to complement AMP NETCONNECT connectors and patch cables Round filler/ Keeps size small Easy to prepare Non-bonded pairs No need to separate wires prior to termination Contains no lead

31 3 1 Category 6 Jacks New slim SL Series profile 90 O or 180 O 110Connect termination using standard punchdown tool Patent pending bendlimiting strain relief Protects cable geometry at point of termination Increases cable retention Coming soon!

32 3 2 Category 6 Jacks Paired terminals for improved crosstalk performance Minimize pair untwist Maximize pair separation Wedge-shaped towers for easy pair splitting Pairs stay tightly twisted Pairs are physically separated

33 3 3 Category 6 Jacks Free-end compensation Category 6 crosstalk compensation performed by secondary PC board Compensation is separate from signal path

34 3 4 Category 6 Patch Panels 12, 24, 48 and 96 port sizes Accept 9 mm and 12 mm labels, icons Supported by AMP NETCONNECT Labeling System software

35 Category 6 Patch Panels 3 5 Use identical circuitry for each port to ensure consistent performance Many panels use different circuitry for each port. This means that the performance is different for each port.

36 3 6 Category 6 Patch Cable Assemblies Designed to provide optimum performance when combined with AMP NETCONNECT Cat 6 jacks, panels and cable Flexible, robust stranded cable Color matched snagless boots ½ Ft. to 50 ft. lengths

37 The Channel 3 7 The most important performance characteristics are those of the channel. The channel numbers represent the performance of the entire cabling system.

38 3 8 Channel Performance In order to be Cat 6 compliant, the entire cabling system must meet all of the requirements when configured in the worst-case configuration. The worst-case configuration allowed by the TIA is the 100-meter, 4-connector channel. On March 5, 2001 Intertek Testing Services tested AMP NETCONNECT plenum and non-plenum channels constructed from production Category 6 products. The following slides show the absolute worst performance at each frequency point from those tests.

39 3 9 AMP NETCONNECT Cat 6 Channel Performance AMP Spec AMP Spec AMP Spec AMP Spec PSNEXT, db NEXT, db Return Loss, db Attenuation, db Freq. MHz

40 4 0 AMP NETCONNECT Cat 6 Channel Performance AMP Spec AMP Spec AMP Spec AMP Spec PSACR, db ACR, db PSELFEXT, db ELFEXT, db Freq. MHz

41 AMP NETCONNECT ACR Performance db MHz! Spec AMP 20 Headroom Frequency, MHz

42 4 2 AMP NETCONNECT PSACR Performance db MHz! Spec AMP Headroom Frequency, MHz

43 4 3 Why a System Approach? Piecemealing cabling infrastructure components is no longer a viable approach to delivering reliable, high performance networks The entire system must be evaluated as a whole to ensure the best performance The AMP NETCONNECT Category 6 System has been independently tested to confirm 250 MHz bandwidth performance Customers attempting to assemble cabling systems through so-called best of breed components are not guaranteed the best system performance levels

44 Category 6 System Benefits 4 4 Designed, engineered and manufactured as a System It s not enough to have good components Installed as a System NETCONNECT Design and Installers (ND&Is) Rigorous and demanding training and qualification Tested and certified as a System Leading-edge, state-of-the art Demanding test procedures are required Warranted as a System From Tyco to the end-user The Total System from One Source

45 Thanks for Your Time! 4 5

TSB-67. Transmission Performance Specifications for Field Testing of UTP Cabling Systems

TSB-67. Transmission Performance Specifications for Field Testing of UTP Cabling Systems TSB-67 Transmission Performance Specifications for Field Testing of UTP Cabling Systems Prepared by: ANSI/EIA/TIA PN-3287 Task Group on UTP Link Performance Required Field Test Parameters for TSB-67 Wire

More information

n Proper pin termination at each end n Continuity to the remote end n Shorts between any two or more conductors n Transposed pairs: n Crossed pairs.

n Proper pin termination at each end n Continuity to the remote end n Shorts between any two or more conductors n Transposed pairs: n Crossed pairs. INTRODUCTION Structured Cabling or data cabling (also known Local Area Network or LAN Cabling) is increasing in its deployment for business, commercial and residential use to carry signaling for networks

More information

Cable Analysis. Extracting Information from Measured Data. The Performance Leader in Hand-Held Network Tools. Fanny Mlinarsky.

Cable Analysis. Extracting Information from Measured Data. The Performance Leader in Hand-Held Network Tools. Fanny Mlinarsky. Cable Analysis Extracting Information from Measured Data Fanny Mlinarsky 2-Nov-98 The Performance Leader in Hand-Held Network Tools Introduction Every cable tells a story. Cable certification measurements

More information

XX.7 Link segment characteristics

XX.7 Link segment characteristics XX.7 Link segment characteristics 10GBASE-T is designed to operate over a 4-pair balanced cabling system. Each of the four pairs supports an effective data rate of 2500 Mbps in each direction simultaneously.

More information

Product Bulletin. Belden DataTwist 4800 Cables

Product Bulletin. Belden DataTwist 4800 Cables Product Bulletin PB 296 Belden DataTwist 4800 Cables DataTwist 4800 UTP Cables provide significant headroom and robust data transmission performance for today s most demanding applications. The cables

More information

Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail

Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail Level III measurement accuracy of field testers for Twisted Pair Copper Cabling Explained in Technical Detail 1 Outline Henriecus Koeman Fluke Networks July 9, 2001 This rather technical discussion contains

More information

Field Measurements of Return Loss

Field Measurements of Return Loss Field Measurements of Return Loss White Paper By Mark Johnston and Jim Tonti Microtest October 21, 1998 Page 1 12/15/99 Overview Return loss is an important new measurement used to qualify the performance

More information

Data sheet Patch cord Cat.6 A AWG m yellow

Data sheet Patch cord Cat.6 A AWG m yellow Illustrations Dimensional drawing Page 1/6 See enlarged drawings at the end of document Product specification especially suitable for shielded and unshielded class E A systems fully shielded Cat.6 A patch

More information

AESA TECHNOLOGY OF LAN CABLE

AESA TECHNOLOGY OF LAN CABLE TECHNOLOGY OF LAN CABLE CONTENT CHAPTER INTRODUCTION CHAPTER LOCAL AREA NETWORK (LAN) CHAPTER STRUCTURED CABLING SYSTEM (SCS) CHAPTER OPTICAL FIBER CABLE CHAPTER STANDARD CHAPTER COPPER LAN CABLE DESIGN

More information

DELTA Test Report. Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model. Performed for Sterling

DELTA Test Report. Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model. Performed for Sterling DELTA Test Report TEST Reg. no. 19 Certification testing of generic cabling products: Unscreened channel, Class E, 4 connector model Performed for Sterling DANAK-19/16909 Project no.: T213173-01 Page 1

More information

Test report number CRT-001b Project number CRT-001b

Test report number CRT-001b Project number CRT-001b 3933 US Route 11 Cortland, NY 13 Telephone: (7) 3-6711 Facsimile: (7) 8-39 www.intertek.com July 24, 215 Nexans Cabling Solutions Alsembergsesteenweg 2, b3 B-151 Buizingen BELGIUM Test report number 12193693CRT-1b

More information

Cable Testing TELECOMMUNICATIONS AND NETWORKING

Cable Testing TELECOMMUNICATIONS AND NETWORKING Cable Testing TELECOMMUNICATIONS AND NETWORKING Analog Signals 2 Digital Signals Square waves, like sine waves, are periodic. However, square wave graphs do not continuously vary with time. The wave holds

More information

Qualification testing of 100 ohm shielded channel, Class EA. Performed for Tyco Electronics Raychem N.V.

Qualification testing of 100 ohm shielded channel, Class EA. Performed for Tyco Electronics Raychem N.V. We help ideas meet the real world DELTA Test Report DANAK TEST Reg. no. 19 Qualification testing of 100 ohm shielded channel, Class EA Performed for Tyco Electronics Raychem N.V. DANAK-19J1636 Project

More information

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860)

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860) 3933 US Route 11 Cortland, NY 1345 Telephone: (67) 753-6711 Facsimile: (67) 758-3659 www.intertek.com December 16, 214 Test Report Number: 33592CRT-137 Project Number: 33592 Legrand North America Superior

More information

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860)

125 Eugene O Neill Drive 6120 Powers Ferry Road New London, CT Suite 150 Ph (860) Atlanta, GA Fax (860) 3933 US Route 11 Cortland, NY 1345 Telephone: (67) 753-6711 Facsimile: (67) 758-3659 www.intertek.com December 16, 214 Test Report Number: 33592CRT-136 Project Number: 33592 Legrand North America Superior

More information

UTP Copper. SFTP Copper. FUTP Copper. Composite. Special Applications Copper. Category 5e. Category 6 Category 5E Category 3. Category 7A Category 7

UTP Copper. SFTP Copper. FUTP Copper. Composite. Special Applications Copper. Category 5e. Category 6 Category 5E Category 3. Category 7A Category 7 05/2011 Table of Contents n Table of Contents 1 n Product Selection 2 n HCM Overview 4 n HCM Certified Cabling Systems 6 n UTP Copper 8 n SFTP Copper 32 n FUTP Copper 36 n Special Applications Copper 42

More information

Independent Testing - For End User Confidence

Independent Testing - For End User Confidence Independent Testing - For End User Confidence ELECTRICAL TRANSMISSION PERFORMANCE TESTING OF SCREENED CATEGORY 6 ISO/IEC, EN & TIA/EIA CONNECTING HARDWARE ACCORDING TO REQUIREMENTS OF 2ND EDITION ISO/IEC

More information

Superiorr Essex. Suite 150

Superiorr Essex. Suite 150 3933 US Route 11 Cortland, NY 1345 Telephone: (67) 753-6711 Facsimile: (67) 758-3659 www.intertek.com March 2, 216 Test Report Number: 1246639CRT-14 Project Number: 1246639 Legrand North America 125 Eugene

More information

10GBASE-T. Channel Model Proposal

10GBASE-T. Channel Model Proposal Channel Model Proposal March 2004 Orlando, FLA 0 Overview Purpose of presentation: Get agreement on a baseline channel models that will be used for evaluating PHY proposals Channel models must be acceptable

More information

Media. Twisted pair db/km at 1MHz 2 km. Coaxial cable 7 db/km at 10 MHz 1 9 km. Optical fibre 0.2 db/km 100 km

Media. Twisted pair db/km at 1MHz 2 km. Coaxial cable 7 db/km at 10 MHz 1 9 km. Optical fibre 0.2 db/km 100 km Media Attenuation Repeater spacing Twisted pair 10-12 db/km at 1MHz 2 km Coaxial cable 7 db/km at 10 MHz 1 9 km Optical fibre 0.2 db/km 100 km conniq.com provides an excellent tutorial on physical media.

More information

10GBASE-T T Tutorial. SolarFlare Communications IEEE Kauai, Hawaii. November 11, 2002

10GBASE-T T Tutorial. SolarFlare Communications IEEE Kauai, Hawaii. November 11, 2002 10GBASE-T T Tutorial IEEE 802.3 Kauai, Hawaii November 11, 2002 Communications Communications 10GBASE-T IEEE Tutorial, 11/11/2002 1 Agenda Introduction, Cabling & Challenges - George Zimmerman, Ph.D. CEO

More information

- Characteristic impedance of cabling links is characterised by Return Loss

- Characteristic impedance of cabling links is characterised by Return Loss ISO/IEC 11801 ISO 11801 is the principle design standard for structured cabling systems for all countries of the world that do not have more specific standards, such as ISO 11801 (European Union), TIA

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 61935-1 Edition 3.0 2009-07 Specification for the testing of balanced and coaxial information technology cabling Part 1: Installed balanced cabling as specified in ISO/IEC 11801

More information

Call For Interest PoE- plus. Chris Di Minico MC Communications

Call For Interest PoE- plus. Chris Di Minico MC Communications Call For Interest PoE- plus Chris Di Minico MC Communications cdiminico@ieee.org 1 IEEE 802.3 CFI Powering Ethernet Devices Over Data Cabling IEEE 802.3af Web Cameras Ethernet Switch Data and Power Security

More information

Test Report based on DIN EN ISO/IEC 17025:2005

Test Report based on DIN EN ISO/IEC 17025:2005 Test Report based on DIN EN ISO/IEC 1725:25 GHMT Type Approval 2 Connector Permanent Link, Copper, Class E according ISO/IEC 1181-1 Ed.1. 217-11 Document-no: P4945b-18-E This Test Report with the measurements

More information

CABLE.

CABLE. CABLE www.pcnet-cable.com.tw sales@pcnet-cable.com.tw PCnet Leading Your Net! PCnet was founded in 1985 and is a leading manufacturer of netwking industries. We provide a complete range of products f structured

More information

Application Note 5044

Application Note 5044 HBCU-5710R 1000BASE-T Small Form Pluggable Low Voltage (3.3V) Electrical Transceiver over Category 5 Unshielded Twisted Pair Cable Characterization Report Application Note 5044 Summary The Physical Medium

More information

Data sheet C6 A modul K 180 jack - Keystone style

Data sheet C6 A modul K 180 jack - Keystone style Illustrations Dimensional drawing Cut-out Page 1/7 See enlarged drawings at the end of document Product specification modular Cat.6 A termination unit RJ45 mounting version: Keystone, 180 cable feed solid,

More information

Data sheet E-DAT modul 2 port AP Cat.6 A, pearl white

Data sheet E-DAT modul 2 port AP Cat.6 A, pearl white Illustrations Dimensional drawing Wiring Page 1/7 See enlarged drawings at the end of document Product specification surface-mounted termination unit with E-DAT modul component testing for Cat.6 A to ISO/IEC

More information

Data sheet C6 A modul K 90 jack - keystone style

Data sheet C6 A modul K 90 jack - keystone style Illustrations Dimensional drawing Cut-out Page 1/7 See enlarged drawings at the end of document Product specification modular Cat.6 A termination unit RJ45 mounting version: Keystone, 90 cable feed solid,

More information

IEEE Std 802.3ap (Amendment to IEEE Std )

IEEE Std 802.3ap (Amendment to IEEE Std ) IEEE Std 802.3ap.-2004 (Amendment to IEEE Std 802.3.-2002) IEEE Standards 802.3apTM IEEE Standard for Information technology. Telecommunications and information exchange between systems. Local and metropolitan

More information

QAM-Based Transceiver Solutions for Full-Duplex Gigabit Ethernet Over 4 Pairs of UTP-5 Cable. Motivation for Using QAM

QAM-Based Transceiver Solutions for Full-Duplex Gigabit Ethernet Over 4 Pairs of UTP-5 Cable. Motivation for Using QAM QAM-Based Transceiver Solutions for Full-Duplex Gigabit Ethernet Over 4 Pairs of UTP-5 Cable Henry Samueli, Jeffrey Putnam, Mehdi Hatamian Broadcom Corporation 16251 Laguna Canyon Road Irvine, CA 92618

More information

Install & Go SMARTen (Cat.6A) STP Trunk Cable Assembly General

Install & Go SMARTen (Cat.6A) STP Trunk Cable Assembly General Install & Go SMARTen (Cat.6A) STP Trunk General Cat 8 Filler Cat.6A U/FTP Horizontal cables (x6) Fan-Out Cables Cat.6A STP Keystones TRUNK CABLE SECTION VIEW Trunk Isometric Front View RiT s Copper Install

More information

Test Report based on DIN EN ISO/IEC 17025: 2005

Test Report based on DIN EN ISO/IEC 17025: 2005 Test Report based on DIN EN ISO/IEC 1725: 25 GHMT Type Approval 2 Connector Permanent Link, Copper, Class EA according ISO/IEC 1181-1 Ed.1. Document-no: P582a-18-E This Test Report with the measurements

More information

Cabling Ad Hoc Cat 5e Measurements

Cabling Ad Hoc Cat 5e Measurements Cabling Ad Hoc Cat 5e Measurements Larry Cohen Solarflare Communications 1 Overview Cabling Ad Hoc Test Plan Measurement One Cat 5e horizontal cable sample, four test channel configurations characterized

More information

Modular Plug Connectors Compliant to Enhanced Category 5 Standards

Modular Plug Connectors Compliant to Enhanced Category 5 Standards Modular Plug Connectors Compliant to Enhanced Category 5 Standards TM2P Series (Shielded Type) TM22P-88P (Non-shielded Type) Features. Supports High-Speed LAN Transmission Conforms to requirements of TIA/EIA-568B

More information

B. Division-16 Basic Materials and Methods section apply to work specified in this section.

B. Division-16 Basic Materials and Methods section apply to work specified in this section. Section 16745 PREMISE CABLING SYSTEMS PART ONE GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification

More information

Data sheet MC GC1000 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft

Data sheet MC GC1000 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft Page 1/6 MC GC0 pro23 Cat.7 S/FTP 4P LSHF-FR 1640 ft 18427034141 Illustrations Principle diagram Product specification 10 GBit installation cable, simplex installation cable Cat.7 AWG 23 S/FTP with wires

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 +1-603-862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu +1-603-862-0166

More information

Modular Plug Connectors Compliant to Enhanced Category 5 Standards

Modular Plug Connectors Compliant to Enhanced Category 5 Standards Modular Plug Connectors Compliant to Enhanced Category 5 Standards TM2P Series (Shielded Type) TM22P-88P (Non-shielded Type) Features. Supports High-Speed LAN Transmission Conforms to requirements of TIA/EIA-568B

More information

Category 6 UTP EuroClass C ca Cables

Category 6 UTP EuroClass C ca Cables Category 6 UTP EuroClass C ca Cables Datasheet: GD103704v1 APPLICATION Brand-Rex Cat6Plus C6U cables exceed the Category 6 performance standards. They are rated to 250MHz and are suitable for use in all

More information

10GBASE-T Transmitter Key Specifications

10GBASE-T Transmitter Key Specifications 10GBASE-T Transmitter Key Specifications Sandeep Gupta, Jose Tellado Teranetics, Santa Clara, CA sgupta@teranetics.com 5/19/2004 1 1000BASE-T Transmitter spec. overview Differential voltage at MDI output

More information

Part Number: 7953A Cat 6 600V DataTuff, (4 pr) 23 AW G Solid BC, PP/PVC/PVC, Foil Shld, CMR, CMX-Outdoor

Part Number: 7953A Cat 6 600V DataTuff, (4 pr) 23 AW G Solid BC, PP/PVC/PVC, Foil Shld, CMR, CMX-Outdoor Part Number: Cat 6 600V DataTuff, (4 pr) 23 AW G Solid BC, PP/PVC/PVC, Foil Shld, CMR, CMX-Outdoor Product Description Four Cat 6 23 AW G solid bare copper conductors, bonded pair polypropylene insulation,

More information

University of New Hampshire InterOperability Laboratory Fast Ethernet Consortium

University of New Hampshire InterOperability Laboratory Fast Ethernet Consortium University of New Hampshire InterOperability Laboratory Fast Ethernet Consortium As of February 25, 2004 the Fast Ethernet Consortium Clause 25 Physical Medium Dependent Conformance Test Suite version

More information

Technical Committee Mb/s Physical Layer Specification for Category-3 Unshielded Twisted Pair. af-phy

Technical Committee Mb/s Physical Layer Specification for Category-3 Unshielded Twisted Pair. af-phy Technical Committee 155.52 Mb/s Physical Layer Specification for Category-3 Unshielded Twisted Pair af-phy-0047.000 November, 1995 af-phy-0047.000 155.52 Mb/s Physical Layer Specification for Category-3

More information

Communications Integrators, Inc. June S. Wilson Street, Suite 105 Tempe, Arizona Toll Free (800) Web Site

Communications Integrators, Inc. June S. Wilson Street, Suite 105 Tempe, Arizona Toll Free (800) Web Site Communications Integrators, Inc. June 2008 2625 S. Wilson Street, Suite 105 Tempe, Arizona 85282 Toll Free (800) 679-9711 Web Site www.ciinet.com Product Guide Specification Specifier Notes: This product

More information

Data sheet C6 A RJ45 field plug pro

Data sheet C6 A RJ45 field plug pro Illustrations Dimensional drawing Page 1/6 See enlarged drawings at the end of document Product specification Cat.6 A class E A RJ45 plug to be assembled in the field fully shielded and multi-port capable

More information

Category 7 A /Class F A Products

Category 7 A /Class F A Products CATEGORY 7 A /CLASS F A PRODUCTS Category 7 A /Class F A Products Exceeding ISO/IEC category 7 A /class F A specifications, Siemonʼs fully shielded TERA endto-end cabling solution is the highest-performing,

More information

Four Cat 5e 24 AW G Bonded-Pairs solid bare copper conductors, polyolefin insulation, PVC jacket.

Four Cat 5e 24 AW G Bonded-Pairs solid bare copper conductors, polyolefin insulation, PVC jacket. Part Number: 7923A Cat 5e MSHA DataTuff, (4 pr) 24 AW G Solid BC, PO/PVC, EtherNet/IP, CMR, CMX-Outdoor Product Description Four Cat 5e 24 AW G Bonded-Pairs solid bare copper conductors, polyolefin insulation,

More information

Data sheet MC GC1200 pro22 Cat.7A S/FTP 4P LSHF-FR, class Dca s2 d2

Data sheet MC GC1200 pro22 Cat.7A S/FTP 4P LSHF-FR, class Dca s2 d2 Page 1/7 Illustrations Principle diagram See enlarged drawings at the end of document Product specification 10 GBit installation cable, simplex installation cable Cat.7A AWG 22 S/FTP with wires shielded

More information

Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification

Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification Samtec MODS-LJ Series (LIFEJACK ) Category 5/5e Qualification J. Ferry, C. Arroyo Copyright 2008 Samtec, Inc Page 1 Summary LIFEJACK met or exceeded TIA/EIA-568-B.2-2001 Category 5e requirements for Insertion

More information

Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada

Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada Some considerations concerning alien crosstalk Dr.-Ing. J.-H. (Jo) Walling Consultant Beaconsfield, P.Q. Canada jo.walling@sympatico.ca 0. Summary Contrary to the simplified perception about alien crosstalk,

More information

Data sheet MC GC1200 pro22 Cat.7A S/FTP 2x4P LSHF-FR 1640 ft

Data sheet MC GC1200 pro22 Cat.7A S/FTP 2x4P LSHF-FR 1640 ft Page 1/7 Illustrations Principle diagram Product specification 10 GBit installation cable, duplex installation cable Cat.7A AWG 22 S/FTP with wires shielded in pairs 2x4 pairs (PiMF) pair shield: plastic

More information

10GBASE-S Technical Feasibility

10GBASE-S Technical Feasibility 10GBASE-S Technical Feasibility Picolight Cielo IEEE P802.3ae Los Angeles, October 2001 Interim meeting 1 10GBASE-S Feasibility Supporters Petar Pepeljugoski, IBM Tom Lindsay, Stratos Lightwave Bob Grow,

More information

CAT 6 Data Wiring System Connectors

CAT 6 Data Wiring System Connectors NEW CAT 6 Data Wiring System Connectors TM2 Series Features. High-Speed Data Transfer Conforms to the TIA/EIA-568B.2- data Wiring standard, thereby clears CAT 6 transfer performance requirements. As such,

More information

Power over Ethernet Consortium Interoperability Test Suite v2.2 Report

Power over Ethernet Consortium Interoperability Test Suite v2.2 Report Power over Ethernet Consortium Interoperability Test Suite v2.2 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 (603) 862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu 603.862.0116

More information

NETWORK CONNECTIVITY SYSTEMS

NETWORK CONNECTIVITY SYSTEMS NETWORK CONNECTIVITY SYSTEMS Installation Cable KS-STP Category 7 Installation Cable Certificates 10GBaseT FTP Category 6 Installation Cable UTP Category 6 Installation Cable UTP Category 5E Installation

More information

Independent Testing - For End User Confidence

Independent Testing - For End User Confidence Independent Testing - For End User Confidence EVALUATION OF PERFORMANCE OF LEVEL IIIe FIELD TESTER FROM FLUKE NETWORKS, TYPE DTX-1800 CABLE ANALYZER, FOR 500 MHz PERMANENT LINK MEASUREMENTS Main Unit,

More information

Data sheet. E-DAT modul 3 port AP Cat.6A, pure white. Illustrations P/N E EAN Product specification. Page 1/

Data sheet. E-DAT modul 3 port AP Cat.6A, pure white. Illustrations P/N E EAN Product specification. Page 1/ Page 1/7 Illustrations Dimensional drawing Wiring See enlarged drawings at the end of document Product specification surface-mounted termination unit with E-DAT modul component testing for Cat.6A to ISO/IEC

More information

UTP Cat 5e cable (200 MHz) (PVC sheath)

UTP Cat 5e cable (200 MHz) (PVC sheath) JetLan is the only structured cabling system that includes all the passive components required for the installation or adaptation of your data network, as we include all the different types of high performance

More information

Data sheet C6 A RJ45 field plug pro 360

Data sheet C6 A RJ45 field plug pro 360 Illustrations Dimensional drawing See enlarged drawings at the end of document Product specification Cat.6 A class E A RJ45 plug to be assembled in the field fully shielded and multi-port capable variable

More information

The Amphenol Alden Products Company Industrial Ethernet Family of Products

The Amphenol Alden Products Company Industrial Ethernet Family of Products The Amphenol Alden Products Company Industrial Ethernet Family of Products The AmphenolAlden Products Company Industrial Ethernet Family of Products Ethernet Migrates Out of the Office Environment to the

More information

IEEE Draft P802.3ap/WP0.5 Draft Amendment to IEEE Std September 24, 2004

IEEE Draft P802.3ap/WP0.5 Draft Amendment to IEEE Std September 24, 2004 0 0 0 0 0 Editor s Notes: To be removed prior to final publication.. The Table of Contents, Table of Figures and Table of Tables are added for reading convenience. This document is a straw man proposal.

More information

5/8/16/24 Ports. Fast Ethernet Switch. User s Guide VER:1.0

5/8/16/24 Ports. Fast Ethernet Switch. User s Guide VER:1.0 5/8/16/24 Ports Fast Ethernet Switch User s Guide VER:1.0 TABLE OF CONTENTS 1 INTRODUCTION 1.1 Unpacking... 2 1.2 Front Panel..... 2 1.3 Rear Panel...... 2 1.4 LED Indicators.... 2 1.5 Features... 3 2

More information

New Product Bulletin. Belden Digital Audio Cable. Belden Brilliance AES/EBU

New Product Bulletin. Belden Digital Audio Cable. Belden Brilliance AES/EBU New Product Bulletin NP 267 Belden Digital Audio Cable Belden Brilliance AES/EBU Digital Audio Cable, Part No. 1353A, is a robust single-pair Cat 5e patch cord that utilizes Belden s exclusive Bonded-Pair

More information

IEEE Draft P802.3ap/WP0.6 Draft Amendment to IEEE Std September 28, 2004

IEEE Draft P802.3ap/WP0.6 Draft Amendment to IEEE Std September 28, 2004 0 0 0 0 0 Editor s Notes: To be removed prior to final publication.. The Table of Contents, Table of Figures and Table of Tables are added for reading convenience. This document is a straw man proposal.

More information

Install & Go Cat.8 STP Trunk Cable Assembly Description

Install & Go Cat.8 STP Trunk Cable Assembly Description Description Cat 8 Filler Cat.8.2 S/FTP Horizontal cables (x6) Fan-Out Cables Cat 8 STP Keystones TRUNK CABLE SECTION VIEW Assembly Isometric Front View RiT s Copper Install & Go System provides a pre-terminated

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 +1-603-862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu +1-603-862-0166

More information

1) The addition of TCL and ELTCTL requirements to Category 6

1) The addition of TCL and ELTCTL requirements to Category 6 Subject 444 TO: SUBJECT: 455 East Trimble Road San Jose, CA 95131 July 28, 2008 Subscribers to UL s Listing and Verification Services for Communications Cable (DUZX) Revised Test and Follow-Up Service

More information

Test Report. Test Result: PASS

Test Report. Test Result: PASS Test Report Designation : C6 A TIA/EIA68B. UTP Length :. m Temp :. Deg C Specification : CAT6 A MHZ UTP Test Date/Time : 11--16 1:1 Sample-ID-No. : GGRQ4 Customer : Rertech Drum no. :. Cable type : CAT6A

More information

Install & Go Cat.8 S/FTP Trunk Cable Assembly Description

Install & Go Cat.8 S/FTP Trunk Cable Assembly Description Description Cat 8 Filler Cat.8.2 S/FTP Horizontal cables (x6) Fan-Out Cables Cat 8 STP Keystones TRUNK CABLE SECTION VIEW Assembly Isometric Front View RiT s Copper Install & Go System provides a pre-terminated

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 (603) 862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu 603.862.0166

More information

SFP Cooper 1000Base-T 100M SL-SFP-3T-XX

SFP Cooper 1000Base-T 100M SL-SFP-3T-XX SFP Cooper 1000Base-T 100M SL-SFP-3T-XX Overview Sourcelight SL-SFP-3T-XX Copper Small Form Pluggable (SFP) transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and

More information

Data sheet C6 A RJ45 field plug pro 360

Data sheet C6 A RJ45 field plug pro 360 Illustrations Dimensional drawing Page 1/6 See enlarged drawings at the end of document Product specification Cat.6 A class E A RJ45 plug to be assembled in the field fully shielded and multi-port capable

More information

Automatic measuring system for LAN cables AXT & Cat 8 HF only

Automatic measuring system for LAN cables AXT & Cat 8 HF only Picture for information only Automatic measuring system for LAN cables AXT & Cat 8 HF only The fastest measuring system on the market Checked against certified ISO 17025 standards High accuracy Easy to

More information

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report

Power over Ethernet Consortium Interoperability Test Suite v2.3 Report Power over Ethernet Consortium Interoperability Test Suite v2.3 Report UNH-IOL 121 Technology Drive, Suite 2 Durham, NH 03824 (603) 862-0090 Consortium Manager: Gerard Nadeau grn@iol.unh.edu 603.862.0166

More information

PHY PMA electrical specs baseline proposal for 803.an

PHY PMA electrical specs baseline proposal for 803.an PHY PMA electrical specs baseline proposal for 803.an Sandeep Gupta, Teranetics Supported by: Takeshi Nagahori, NEC electronics Vivek Telang, Vitesse Semiconductor Joseph Babanezhad, Plato Labs Yuji Kasai,

More information

Bill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables.

Bill Ham Martin Ogbuokiri. This clause specifies the electrical performance requirements for shielded and unshielded cables. 098-219r2 Prepared by: Ed Armstrong Zane Daggett Bill Ham Martin Ogbuokiri Date: 07-24-98 Revised: 09-29-98 Revised again: 10-14-98 Revised again: 12-2-98 Revised again: 01-18-99 1. REQUIREMENTS FOR SPI-3

More information

10 Mb/s Single Twisted Pair Ethernet Evaluation Board Noise Measurements Marcel Medina Steffen Graber Pepperl+Fuchs

10 Mb/s Single Twisted Pair Ethernet Evaluation Board Noise Measurements Marcel Medina Steffen Graber Pepperl+Fuchs 10 Mb/s Single Twisted Pair Ethernet Evaluation Board Noise Measurements Marcel Medina Steffen Graber Pepperl+Fuchs IEEE P802.3cg 10 Mb/s Single Twisted Pair Ethernet Task Force 9/6/2017 1 Content AWGN/Impulsive

More information

Category 6 A F/FTP Euroclass C ca Cables

Category 6 A F/FTP Euroclass C ca Cables Category 6 A F/FTP Euroclass C ca s Datasheet: GD103266v2 APPLICATION The Brand-Rex AC6F/FTP C ca cables are compliant with the European Construction Products Regulation, achieving Euroclass level C ca

More information

Migration to 50/125 µm in the Local Area Network

Migration to 50/125 µm in the Local Area Network Migration to 50/125 µm in the Local Area Network By Doug Coleman Introduction Enterprise local area networks (LAN) should be designed to support legacy applications as well as emerging high-data-rate applications.

More information

WHITE PAPER INTRODUCTION DC RESISTANCE UNBALANCE TESTING: EASY, LOW-COST INSURANCE FOR YOUR POE SYSTEMS

WHITE PAPER INTRODUCTION DC RESISTANCE UNBALANCE TESTING: EASY, LOW-COST INSURANCE FOR YOUR POE SYSTEMS WHITE PAPER DC RESISTANCE UNBALANCE TESTING: EASY, LOW-COST INSURANCE FOR YOUR POE SYSTEMS INTRODUCTION Originally ratified by IEEE in 999 and 00 respectively, gigabit Ethernet (000BASE-T) and power over

More information

Product Specification Gb/s RoHS Compliant Short Wavelength 2x5 SFF Transceiver. FTLF8519F2xTL

Product Specification Gb/s RoHS Compliant Short Wavelength 2x5 SFF Transceiver. FTLF8519F2xTL Product Specification 2.125 Gb/s RoHS Compliant Short Wavelength 2x5 SFF Transceiver FTLF8519F2xTL PRODUCT FEATURES Up to 2.125 Gb/s bi-directional data links Standard 2x5 pin SFF footprint (MSA compliant)

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD IEC 61935-1 Edition 4.0 2015-12 colour inside Specification for the testing of balanced and coaxial information technology cabling Part 1: Installed balanced cabling as specified

More information

Detailed Specifications & Technical Data

Detailed Specifications & Technical Data RFP Specification #17-11125-C, Exhibit 2 Programmable Light Poles for BART Plaza ENGLISH MEASUREMENT VERSION 1502SB Multi-Conductor - Multimedia Control Cable For more Information please call 1-800-Belden1

More information

GIGABIT ETHERNET CONSORTIUM

GIGABIT ETHERNET CONSORTIUM GIGABIT ETHERNET CONSORTIUM Clause 126 2.5G/5GBASE-T PMA Test Suite Version 1.2 Technical Document Last Updated: March 15, 2017 2.5, 5 and 10 Gigabit Ethernet Testing Service 21 Madbury Road, Suite 100

More information

Data sheet C6 A RJ45 field plug pro 360

Data sheet C6 A RJ45 field plug pro 360 Illustrations Dimensional drawing Page 1/6 See enlarged drawings at the end of document Product specification Cat.6 A class E A RJ45 plug to be assembled in the field fully shielded and multi-port capable

More information

400G CWDM8 10 km Optical Interface Technical Specifications Revision 1.0

400G CWDM8 10 km Optical Interface Technical Specifications Revision 1.0 400G CWDM8 10 km Optical Interface Technical Specifications Revision 1.0 Contact: cwdm8-msa.org CWDM8 10 km Technical Specifications, Revision 1.0 1 Table of Contents 1. General...5 1.1. Scope...5 1.2.

More information

2.5G/5G/10G ETHERNET Testing Service

2.5G/5G/10G ETHERNET Testing Service 2.5G/5G/10G ETHERNET Testing Service Clause 126 2.5G/5GBASE-T PMA Test Plan Version 1.3 Technical Document Last Updated: February 4, 2019 2.5, 5 and 10 Gigabit Ethernet Testing Service 21 Madbury Road,

More information

SECTION BUILDING WIRE AND CABLE

SECTION BUILDING WIRE AND CABLE SECTION 260519 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Building wire and cable. 2. Wiring connectors and connections. B. RELATED SECTIONS 1. Section 26 05 53 Electrical Identification. 2. Section

More information

Data sheet C5 RJ45 field plug pro 2P PROFINET

Data sheet C5 RJ45 field plug pro 2P PROFINET Illustrations Dimensional drawing Page 1/5 See enlarged drawings at the end of document Product specification Cat.5 class D RJ45 plug, 2 pairs, to be assembled in the field fully shielded and multi-port

More information

FCOPPER-SFP BASE-TX Copper SFP Transceiver

FCOPPER-SFP BASE-TX Copper SFP Transceiver 100BASE-TX Copper SFP Transceiver March 27, 2012 Product Overview The electrical Small Form Factor Pluggable (SFP) transceiver module is specifically designed for converting 100BASE-FX NRZI port interface

More information

Add names. Midspan / Channel Requirements below 1MHz, New material +Updates. Yair Darshan, May, 2008 Page 1

Add names.  Midspan / Channel Requirements below 1MHz, New material +Updates. Yair Darshan, May, 2008 Page 1 IEEE P802.3at Task Force Power Via MDI Enhancements Midspan Adhoc Midspan/Channel Requirements below 1MHz New Material +Updates May 7, 2008 Yair Darshan / Microsemi Corporation Add names Midspan / Channel

More information

Test Report based on DIN EN ISO/IEC 17025

Test Report based on DIN EN ISO/IEC 17025 Test Report based on DIN EN ISO/IEC 17025 GHMT PREMIUM Verification Program Recertification Connector, Copper, Category 6A ISO/IEC 11801 Ed.2.2 This Test Report with the measurements consists of 28 pages.

More information

Data sheet E-DAT Industry RJ45 field plug black Cat.6 Class E A

Data sheet E-DAT Industry RJ45 field plug black Cat.6 Class E A Illustrations Dimensional drawing See enlarged drawings at the end of document Product specification multi-port Cat.6 class E A plug to be assembled in the field compliance with class E A to ISO/IEC 11801

More information

White Paper: DC Resistance Unbalance Testing: Easy, Low-Cost Insurance for Your PoE Systems

White Paper: DC Resistance Unbalance Testing: Easy, Low-Cost Insurance for Your PoE Systems White Paper: DC Resistance Unbalance Testing: Easy, Low-Cost Insurance for Your PoE Systems Originally ratified by IEEE in 1999 and 2003 respectively, gigabit Ethernet (1000BASE-T) and power over Ethernet

More information

ATM Physical Medium Dependent Interface Specification for 155 Mb/s over Twisted Pair Cable

ATM Physical Medium Dependent Interface Specification for 155 Mb/s over Twisted Pair Cable September, 1994 AF-PHY-0015.000 Technical Committee ATM Physical Medium Dependent Interface Specification for 155 Mb/s over Twisted Pair Cable af-phy-0015.000 AF-PHY-0015.000 September, 1994 The ATM Forum

More information

Data sheet. E-DAT modul Cat.6A 8(8) jack, T568B. Illustrations P/N I-B1 EAN Product specification. Page 1/

Data sheet. E-DAT modul Cat.6A 8(8) jack, T568B. Illustrations P/N I-B1 EAN Product specification. Page 1/ Page 1/9 Illustrations Dimensional drawing Cut-out See enlarged drawings at the end of document Product specification modular termination unit Cat.6A, RJ45 component testing for Cat.6A to ISO/IEC 11801

More information

Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables

Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables Indicative picture Phoenix 1004 DT Automatic measuring system for xdsl & LAN cables (100 MHz) Designed to measure all types of telecom and special cables Compliant to all major national standards for telephone,

More information

CAT 6 Data Wiring System Connectors

CAT 6 Data Wiring System Connectors CAT Data Wiring System Connectors TM23 Series Features 1. High-Speed Data Transfer Conforms to the TIA/EIA-58B.2-1 data Wiring standard, thereby clears CAT transfer performance requirements. As such, these

More information