NetPA AT Series Setup Guide

Size: px
Start display at page:

Download "NetPA AT Series Setup Guide"

Transcription

1 DProduct NetPA Series Setup uide This guide provides basic instructions for an experienced technician to install the and NetPA 0070V Networked Power Amplifiers. Both the and NetPA 0070V models are collectively referred to as NetPA in this guide. For additional information and specifications, see the NetPA product page at WARNIN: Installation and service must be performed by experienced personnel only. AVERTISSEMENT : L installation et l entretien doivent être effectués par le personnel autorisé uniquement. 0040V 0.5AMAX Hz A B J C D E F H I 0040V 0.5AMAX NetPA 0070V HPF 70 V OUTPUTS Hz OFF 5060Hz Figure. and NetPA 0070V Rear Panels A IEC AC power input, 00 to 240 VAC, 5060 Hz B ain adjustment (see step 2, on page 8 for C Line out connector (see step 7 on page 2 for D Remote connector (see step 6 on page 2 for E RJ45 Ethernet connector (see step 3 on page 2 for F Link indicator (see Link Indicator LED on page 0 for Reset button (see Resetting the NetPA on page 9 for H Amplified stereo audio output connector (see step 4 on page 2 for I Amplified mono audio output connector (see step 4 on page 2 for J HPF (high pass filter switch) (see step 5 on page 2 for Step Powering Down Equipment Be sure that power to the NetPA is turned off first by disconnecting the power A. NOTE: Adjust the audio level to = (full attenuation) prior to powering the amplifier in step 8. Turn off all other equipment and disconnect the power cables. Verify that the amplifier is disconnected from the power source before proceeding. Step 2 Application Example and Mounting For a typical application example, see Application Example in the user guide. For further mounting instructions, see Mounting the NetPA in the user guide.

2 NetPA Series Setup uide (Continued) Step 3 Connecting the NetPA to the Network Using standard C cable, connect the RJ45 connector E of the NetPA to a LAN for digital audio transport (see Creating a Physical Dante Network on page 9). Step 4 Audio Output Connector Stereo audio output connector Wire the speakers to the output connector of the H using the 4pole captive screw connector, as shown below. Do not tin the wires! Mono audio output connector Wire the speakers to the output connector of the NetPA 0070V I using the 2pole captive screw connector, as shown below. Do not tin the wires! 70 V OUTPUTS Step 5 Setting the High Pass Filter (HPF) On the NetPA 0070V, use a Tweeker or small screwdriver to toggle the high pass filter switch J between Off (no filtering) and 80 Hz (default). Setting the switch to 80 Hz prevents the saturation of speaker input transformers by low frequency signals. The high pass filter can be safely turned off only if the filtering is applied upstream of the amplifier. Step 6 Remote Connector The 3.5 mm, 2pin captive screw remote control port D forces the unit into standby mode when the remote standby pin is shorted to ground. The amplifier wakes from standby and resets the inactivity timer when the connection is reopened. See the user guide for details. Step 7 Line Out Connector Connect an amplifier or other device to the 3pole, 3.5 mm captive screw connectors C for channel and channel 2 () or the single channel (NetPA 0070V). Wire as shown below. Tip Ring Sleeve Balanced Output Audio Output Wiring Tip NO round Here Sleeve Unbalanced Output " (5 mm) MAX. Do not tin the wires! TENTION: For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative ( ) contacts. TENTION : Pour l audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs ( ). NOTE: The signal that comes out of the line output is the same signal that goes into the amplifier stage, prior to the gain potentiometers. (The same audio content coming out of channel amplified output comes out of the channel line output.) 2

3 Product Category Step 8 Powering On the Equipment TENTION: The amplifier must be powered on last. TENTION : L amplificateur doit être allumé en dernier. Reconnect all power cables and switch on all other equipment before powering on the amplifier. The front panel power LED of the NetPA lights green. Step 9 Installing Dante Controller for Windows Software Dante Controller from Audinate is required to select and route digital inputs and outputs to connected Dante compatible devices. Install Dante Controller on a PC running Microsoft Windows 7 or newer. For full details about computer requirements, see the product page on the Extron website. Dante Controller must be installed to rename the connected NetPA to assist identification on the network. Downloading Dante Controller for Windows The software application is available at From enter NetPA in the search field and press <Enter>. The NetPA product page opens. 2 Figure 2. NetPA Product Page 2. Click Downloads (2). The Downloads panel opens. Dante Controller is listed. 3. Click Dante Controller (3). 3 3

4 NetPA Series Setup uide (Continued) The Download Center page opens. 4 5 Figure Fill in the required fields. Download Center Dante Download 5. Click Download dantecontrollernxn.exe. 6. Save the file to your desktop (or other known location). 7. Locate and doubleclick the saved Dante Controller file to begin installation. 8. Follow the onscreen instructions. When the installation completes, close the installation dialog. Step 0 Dante Network Setup Rename the NetPA Dante Controller autodiscovers all Dante devices on the network and advertises itself to allow other Danteenabled devices to communicate with it. The default device name is the word NetPA followed by the last six digits of the MAC address of the device. Multiple devices on the same network can present difficulty identifying inputs and outputs. To avoid confusion, each device must be renamed to a unique identifier. NOTE: To simplify renaming, connect only one Dante device to the network at a time. As each device is renamed, it can remain connected. Ensure the control computer and the NetPA are connected to the same network.. From the start menu select All Programs > Audinate > Dante Controller > Dante Controller. The Dante Controller Network View screen opens. All Dante devices on the network are discovered and listed. 4

5 Product Category 2. From the toolbar, select Device>Device View. 3. The Dante Controller Device View dialog opens. Select your device from the (Select a Dante Device...) dropdown list. NOTES: If there are multiple NetPA s connected to the network that have not been renamed, to identify an individual device you must obtain the MAC address of the desired device from the label on the rear panel. The identify device tool can also be used to identify the unit (see Identifying the Physical Device on page 6). The Device View dialog populates with the selected NetPA information. 4. Click the Device Config tab to open the device configuration page. 5. In the Rename Device panel, enter the new name of the device in the text field. No spaces are allowed in the name. 5

6 NetPA Series Setup uide (Continued) 6. Click Apply. A warning opens. 7. Click Yes to enter the new name, then close the Device Configuration dialog. The new name is written to the NetPA. Repeat as necessary for all NetPA devices. NOTE: After the NetPA is renamed, it can remain connected to the network. However, subsequent devices must be connected one at a time and renamed before the next device is connected. Identifying the Physical Device If the amplifier needs to be physically identified, the identify device tool can be used to aid in its location.. Start with steps through 3 of Rename the NetPA on page To identify the NetPA, click on the eye icon on the toolbar. 3. Both the front panel power LED (see figure 6, A, on page 0) and the rear panel link LED F (see figure, F, on page ) blink amber at a rate of 0.5 Hz for ten seconds, after which the LEDs return to their previous state. 4. Locate the unit with the blinking LEDs. NOTE: For advanced network setup, refer to the user guide. 6

7 Product Category Step Dante Operation Select Devices After the receiver inputs of the NetPA are configured, they must be routed to the other Dante devices on the audio network. Dante Controller is required.. Ensure the control computer and NetPA are connected to the same network. 2. From the start menu select All Programs > Audinate > Dante Controller > Dante Controller. The Dante Controller Network View screen opens. Dante Controller autodiscovers Dante devices on the network and advertises itself to allow other Danteenabled devices to communicate with it. Device inputs are Dante receivers (listed vertically on the left) and device outputs are Dante transmitters (listed horizontally across the top). Transmitters (outputs) connect to receivers (inputs) using the connection matrix. 3. Click the + box next to the NetPA (NetPAClassroom0) in the Dante Receivers column to show all device inputs. 4. Click the + box next to the transmitter (DMP28LectureHall) in the Dante Transmitter row to show all device outputs. 7

8 NetPA Series Setup uide (Continued) Route Inputs and Outputs. Click the + box next to the input channels (receivers) on the NetPA (NetPAClassroom0 in the example above). All device outputs (transmitters) display horizontally. 2. Click the junction of the desired connection (Example: DMP28LectureHall Output0 to NetPAClassroom0 INPUTMONO). A checkmark at the junction indicates the connection is made. A checkmark is also placed next to the receiver channel. NOTE: An input (receiver) can connect to only one output (transmitter). An output (transmitter) can connect to multiple inputs (receivers). 3. Click the junction again to disconnect the input from the output. See the Dante Controller section of the NetPA Series user guide for information on Dante Controller operation. Step 2 Setting the ain Potentiometer Turn up the gain potentiometer to the desired level. When the pot is set to 0 db, and a 0 dbfs signal is transmitted through the Dante port, the amplifier outputs full power. Use a Tweeker or small screwdriver to adjust the audio input gain for the corresponding channel. The analog potentiometers control the gain from = (full attenuation) to 0 db (no gain) to + 6 db gain. NOTE: The potentiometer affects the gain post DAC and pre amplifier stage. The gain potentiometer does not adjust the level of the line output NetPA 0070V

9 0040V 0.5AMAX 5060Hz 0040V ~ A MAX 0040V ~ A MAX MIC 8V DMP 28 C V 0.5AMAX /60 Hz Tx Rx EXP LAN MIC 8V DMP 28 C Hz RS /60 Hz Tx Rx EXP LAN RS V 0.5AMAX 5060Hz POWER 2V.0A MAX I/O 0 IN 002 IN 002 IN002 IN 002 IN AXP 50 C POWER 2V.0A MAX I/O IN 002 IN 002 IN002 IN 002 IN AXP 50 C 0040V 0.5AMAX 5060Hz Product Category Creating a Physical Dante Network A physical network is required to share Dante audio channels between a DMP 28 device and a NetPA. The and NetPA 0070V have an RJ 45 connector located on the back panel that accepts a standard network cable. A DMP 28 based Dante network can be configured in a star or daisy chain network topology using the four port switch and the Dante Controller in switched mode. Star network topology places one DMP 28 C as the central unit, which connects directly to up to three more units. Alternatively, a larger network switch in place of the central DMP 28, allows more than four NetPA s to connect in the star configuration. MIC/LINE INPUTS OUTPUTS DIITAL I/O DMP 28 C Star Network Topology Figure 4. Star Network Topology A daisy chain configuration can also be used. Each NetPA device can connect only to the end of the chain. MIC/LINE INPUTS OUTPUTS DIITAL I/O DMP 28 AXP 50 C # AXP 50 C #2 INPUTS Daisy Chain Network Topology INPUTS Figure 5. Daisy Chain Topology Hybrid versions combining the star and daisy chain topologies can be built, but a ring topology, or any topology that creates a duplicate connection causes a connection failure in Dante Controller. NOTE: Connections between ports in either a star or daisy chain network do not need to be sequential ( to 2, 2 to 3, 3 to 4), nor do they need to be made between the same port numbers ( to, 2 to 2, 3 to 3, 4 to 4). NOTE: At the moment, Dante is not compatible with EEE (Energy Efficient Ethernet) technology. Care should be taken when using a network switch with this technology in a Dante network. If using a managed switch, ensure that it supports disabling EEE on all ports that will be used for Dante traffic. If using an unmanaged switch, do not use models that support the EEE function, as it can not be disabled on these models. For more information on this topic, see the Audinate website. Resetting the NetPA The NetPA utilizes DHCP addressing by default. A recessed reset button on the rear panel (see figure,, on page ) initiates a reset mode. Reset sets the IP addressing mode to DHCP (Dante default), clear the previous IP address, and reset the device name to default. NOTE: Initiating a reset while the NetPA is connected to a transmitting device severs that connection. To reset the NetPA, press and hold down the reset button for ten seconds until both of the rear panel RJ45 Ethernet port LEDs blink twice. NOTE: When the NetPA is first powered on, or reset, the default name shall be NetPAxxxxxx where xxxxxx are the last six digits or letters of the MAC address of the unit. Ethernet Port LEDs 9

10 Link Indicator LED The Link indicator LED (see figure, F, on page ) is locked to the Dante sync signal. This LED indicates three states in normal operation: Blinking ( Hz) reen The Dante card generates network audio clock. The unit is master clock. Solid green The Dante card is locked to network audio clock. The unit is slaved to network audio clock. Off The Dante card is not locked to network audio clock. Front Panel Features LIMITER/PROTECT SINAL NETWORK POWER AMPLIFIER A BC LIMITER/PROTECT SINAL NetPA 0070V NETWORK POWER AMPLIFIER Figure 6. A Power LED NetPA Series Front Panels Lights solid green when powered on and active. Lights amber when: In standby mode. DC voltage is detected on the output. NOTE: The unit can be cleared only by cycling AC power off then back on. Momentarily blinks in the same color and pattern as the rear panel link indicator when the identify device tool is activated (see Identifying the Physical Device on page 6 for more. Once this sequence has completed, the power LED resumes its previous function. B Limiter/Protect LED Lights solid red when the channel is in protection mode, triggered by any of the limiter protection circuits: Clip limiter activated due to excessive clipping Short circuit on output Thermal protection C Signal LED The LED lights green when the input signal is detected and varies in intensity. The green signal LED varies in brightness corresponding to the realtime input signal level. It begins to light at 60 dbfs increasing in steps to full intensity as the signal level increases A 03 5 Extron Headquarters Inside USA/Canada Only Extron USA West Extron USA East FAX FAX Extron Europe Inside Europe Only FAX Extron Asia FAX Extron Japan FAX Extron China FAX Extron Middle East FAX Extron Korea FAX Extron India (Inside India Only) FAX Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.

DPA602 1/7. Multi-Channel Network Amplifier. General Description. Features. Applications. AtlasIED.com. DPA602 Front. DPA602 Back

DPA602 1/7. Multi-Channel Network Amplifier. General Description. Features. Applications. AtlasIED.com. DPA602 Front. DPA602 Back 1/7 DPA602 Multi-Channel Network Amplifier Features Configurations 2 x 300 Watt 70V / 100V (Factory Default) 4 x 150 Watt @ 4Ω 1 x 300 Watt 70V / 100V & 2 x 150 Watt @ 4Ω No Computer Required to Operate

More information

Overview. Features. Technical Data Sheet 1 / 5. Power Amplifier XMV8140-D

Overview. Features. Technical Data Sheet 1 / 5. Power Amplifier XMV8140-D Overview Multi-channel power amplifiers with features designed specifically to benefit installation sound systems. Features Eight-channel power amp that can operate in both high-impedance (70V/100V line)

More information

WPE 48N USER MANUAL Version1.1

WPE 48N USER MANUAL Version1.1 Version1.1 Security instructions 1. Read this manual carefully. 2. Follow all instructions and warnings. 3. Only use accessories specified by WORK PRO. 4. Follow the safety instructions of your country.

More information

Best Practices Guide Polycom SoundStructure and HDX Microphones

Best Practices Guide Polycom SoundStructure and HDX Microphones Best Practices Guide Polycom SoundStructure and HDX Microphones This document introduces HDX microphones and the best practices for using the HDX microphones with SoundStructure devices. In addition this

More information

Stereo / Mono. Audio Power Amplifier - 60 W. Introduction. Applications

Stereo / Mono. Audio Power Amplifier - 60 W. Introduction. Applications Amplifier - 60 W Introduction The Atlona Gain 60 (AT-GAIN-60) is a compact power amplifier designed for low or high impedance applications. A mode selector switch allows the Gain 60 to deliver two channels

More information

ECM S10 Partition Sensor Setup Guide

ECM S10 Partition Sensor Setup Guide Product Category EC Partition ensor etup uide EC is a pollution degree product with a rated impulse voltage of V. Construction of Control is defined as Independently ounted. The purpose of the control

More information

Boulder 810 Preamplifier

Boulder 810 Preamplifier Boulder 810 Preamplifier Owners Manual 6/8/06 Boulder Amplifiers, Inc. 3235 Prairie Ave. Boulder, CO 80301 www.boulderamp.com APPENDIX RECORDING BOULDER LINK PROGRAMMING REMOTE CONTROL OPERATION GETTING

More information

CXD-Q 8-Channel Amplifier

CXD-Q 8-Channel Amplifier CXDQ 8Channel Amplifier Quick Start Guide EXPLANATION OF TERMS AND SYMBOLS The term WARNING! indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily

More information

Specifications MPS 602

Specifications MPS 602 Specifications MPS 602 Video VGA Inputs Gain... Unity Bandwidth... 350 MHz (-3 db) Crosstalk... -50 db @ 10 MHz, -30 db @ 100 MHz Switching speed...

More information

Programming Parameter Guide

Programming Parameter Guide Secure Wireless Microphone ELITE PRO Programming Parameter Guide rev:1 How to use Programmer: Start Programming application Runs On PC or Mac running Windows 7/10. To put Handset into programming mode,

More information

3 GHz Carrier Backhaul Radio. Model: AF-3X. Tel: +44 (0) Fax: +44 (0) LINK GPS MGMT DATA DATA

3 GHz Carrier Backhaul Radio. Model: AF-3X.   Tel: +44 (0) Fax: +44 (0) LINK GPS MGMT DATA DATA LINK GPS MGMT DATA DATA MGMT GPS LINK 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you

More information

"Terminal RG-1000" Customer Programming Software. User Guide. August 2016 R4.3

Terminal RG-1000 Customer Programming Software. User Guide. August 2016 R4.3 "Terminal RG-1000" Customer Programming Software User Guide August 2016 R4.3 Table of Contents Table of Contents Introduction 2 3 1.1 Software installation 3 1.2 Connecting the RG-1000 GATEWAYs to the

More information

Setup Utility Guide. ADX-0808 and ADX-1616 Audio Matrix Pre-amp Systems

Setup Utility Guide. ADX-0808 and ADX-1616 Audio Matrix Pre-amp Systems Setup Utility Guide ADX-0808 and ADX-1616 Audio Matrix Pre-amp Systems Configuration Using the Setup Utility The Setup Utility is the most efficient way to set up ADX advanced features (using *Mac or PC),

More information

Tel. 0621/ FAX 0621/

Tel. 0621/ FAX 0621/ Änderungen und Irrtümer vorbehalten Video VGA Gain Bandwidth Crosstalk Switching speed Unity 350 MHz (-3 db) -50 db @ 10 MHz, -30 db @ 100 MHz

More information

Focusrite Saffire 6 USB. User Guide

Focusrite Saffire 6 USB. User Guide Focusrite Saffire 6 USB User Guide 1 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus

More information

FreeSpace IZA 250-LZ / 190-HZ TECHNICAL DATA SHEET. integrated zone amplifier. Key Features. Product Overview. Product Information.

FreeSpace IZA 250-LZ / 190-HZ TECHNICAL DATA SHEET. integrated zone amplifier. Key Features. Product Overview. Product Information. Product Overview For background/foreground music and paging applications, the Bose FreeSpace IZA 250-LZ and IZA 190-HZ s are designed to deliver premium sound, provide simplified set up and easy daily

More information

Boulder W Mono Power Amplifier

Boulder W Mono Power Amplifier Boulder 1050 500 W Mono Power Amplifier Owners Manual 4/11/04 Boulder Amplifiers, Inc. 3235 Prairie Ave. Boulder, CO 80301 www.boulderamp.com APPENDIX BOULDER LINK REMOTE CONTROL OPERATION GETTING STARTED

More information

FreeSpace IZA 2120-LZ Integrated Zone Amplifier

FreeSpace IZA 2120-LZ Integrated Zone Amplifier Product Description For background/foreground music and paging applications, Bose FreeSpace IZA 2120-LZ integrated zone amplifier elevates the audio experience when using FreeSpace loudspeakers. Optimized

More information

Mbox Basics Guide. Version 6.4 for LE Systems on Windows XP and Mac OS X. Digidesign

Mbox Basics Guide. Version 6.4 for LE Systems on Windows XP and Mac OS X. Digidesign Mbox Basics Guide Version 6.4 for LE Systems on Windows XP and Mac OS X Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support (USA)

More information

JEM Radio II Operation Guide. Manual P/N M Victor Place Colorado Springs, Colorado

JEM Radio II Operation Guide. Manual P/N M Victor Place Colorado Springs, Colorado JEM Radio II Manual P/N M09999-999 2115 Victor Place Colorado Springs, Colorado 80915 800.284.0399 www.jemcom.com Table of Contents Display... 3 Channel Entry... 4 Shortcuts... 4 Text Messages... 4 Buttons...

More information

Warning: Electrical Hazard... 3 Safety Instruction Sheet for STG Product Overview What s in the box?... 4

Warning: Electrical Hazard... 3 Safety Instruction Sheet for STG Product Overview What s in the box?... 4 STG-2412 User Guide Warning: Electrical Hazard... 3 Safety Instruction Sheet for STG-2412... 3 Product Overview... 4 What s in the box?... 4 Using STG-2412 for Mixing, Processing, and Recording... 5 Software

More information

Installer Guide. Read Me First... PA 8 ELITE PA 8 ULTRA ELITE PA 16 ELITE. Multi-Channel Power Amplifiers. If you need help...

Installer Guide. Read Me First... PA 8 ELITE PA 8 ULTRA ELITE PA 16 ELITE. Multi-Channel Power Amplifiers. If you need help... Installer Guide PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE Multi-Channel Power Amplifiers Read Me First... If you need help.... Check the online help of the Web Installer Interface.. Check our website support

More information

Owner s Manual HPA-DAC2. HPA-DAC2 Dante Accessory Card. AtlasIED.com

Owner s Manual HPA-DAC2. HPA-DAC2 Dante Accessory Card. AtlasIED.com Owner s Manual 1 AtlasIED.com Owner s Manual Description The accessory card is designed to work in conjunction with HPA Series 2-channel amplifiers. The is a 2-input Dante receiver that features digital

More information

IX Feb Operation Guide. Sequence Creation and Control Software SD011-PCR-LE. Wavy for PCR-LE. Ver. 5.5x

IX Feb Operation Guide. Sequence Creation and Control Software SD011-PCR-LE. Wavy for PCR-LE. Ver. 5.5x IX000693 Feb. 015 Operation Guide Sequence Creation and Control Software SD011-PCR-LE Wavy for PCR-LE Ver. 5.5x About This Guide This PDF version of the operation guide is provided so that you can print

More information

SR3400 Base Station Module Configuration and Use Series-2 Cards Only

SR3400 Base Station Module Configuration and Use Series-2 Cards Only SR3400 Base Station Module Configuration and Use Series-2 Cards Only A.W. Communication Systems Ltd Crook Barn, The Crook Rowel Town, Carlisle Cumbria Telephone (44) 1697-748777 Fax (44) 1697-748778 www.toneremote.com

More information

3050 Stereo Power Amplifier

3050 Stereo Power Amplifier 3050 Stereo Power Amplifier Owners Manual 10/26/2016 Boulder Amplifiers, Inc. 255 Taylor Ave. Louisville, CO 80027 (303) 449-8220 www.boulderamp.com Fault Conditions Boulderlink Appendix Remote Control

More information

Mounting Instruction. Compact Mini EGC Amplifier and Application

Mounting Instruction. Compact Mini EGC Amplifier and Application Mounting Instruction Compact Mini EGC Amplifier 93230 and 93240 Application The Compact Mini EGC Amplifier type 93230 and type 93240 has one active output and is mainly used as distribution amplifier.

More information

INSTRUCTION MANUAL IP REMOTE CONTROL SOFTWARE RS-BA1

INSTRUCTION MANUAL IP REMOTE CONTROL SOFTWARE RS-BA1 INSTRUCTION MANUAL IP REMOTE CONTROL SOFTWARE RS-BA FOREWORD Thank you for purchasing the RS-BA. The RS-BA is designed to remotely control an Icom radio through a network. This instruction manual contains

More information

User Guide FFFA

User Guide FFFA User Guide FFFA001253 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...4 System Requirements....4

More information

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. June 2018 R2.2.2 v2

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. June 2018 R2.2.2 v2 Customer Programming Software RG-1000e (CPS RG-1000e) User Guide June 2018 R2.2.2 v2 Table of Contents Table of Contents Foreword 3 Revision history 4 Introduction 5 1. RG-1000e Customer Programming Software

More information

Installation Instructions

Installation Instructions Installation Instructions www.phonak.com 1. Setup is a Dynamic SoundField receiver that upgrades an amplification system to intelligent dynamic behavior. This guide is aimed at professional installers.

More information

Sampling and Reconstruction

Sampling and Reconstruction Experiment 10 Sampling and Reconstruction In this experiment we shall learn how an analog signal can be sampled in the time domain and then how the same samples can be used to reconstruct the original

More information

Protea-Equipped Media Amplifier

Protea-Equipped Media Amplifier 5-Year Warranty Hand-built in Webster, NY 70V Rated 100V Rated pema4125 pema4250 pema8125 pema8250 PEMA PEMA sets a new industry benchmark for value-engineered zone sound systems. By seamlessly merging

More information

Protea-Equipped Media Amplifier

Protea-Equipped Media Amplifier 5-Year Warranty Hand-built in Webster, NY 70V Rated 100V Rated pema4125 pema4250 pema8125 pema8250 PEMA PEMA sets a new industry benchmark for value-engineered zone sound systems. By seamlessly merging

More information

1160 Stereo Power Amplifier

1160 Stereo Power Amplifier 1160 Stereo Power Amplifier 03/01/2018 Rev. 1.0 P/N: 91055 Boulder Amplifiers, Inc. 255 S. Taylor Ave. Louisville, CO 80027 (303) 449-8220 www.boulderamp.com About About Boulder Amplifiers, Inc. Boulder

More information

PC Tune PC Tune Test Procedures for 5100 Series Portable Radios

PC Tune PC Tune Test Procedures for 5100 Series Portable Radios PC Tune PC Tune Test Procedures for 5100 Series Portable Radios Part Number 002-9998-6513014 August 2008 Copyright 2006, 2007, 2008 by EFJohnson Technologies The EFJohnson Technologies logo, PC Configure,

More information

MC108A-2 RF MULTI-COUPLER USER S GUIDE

MC108A-2 RF MULTI-COUPLER USER S GUIDE MC108A-2 RF MULTI-COUPLER USER S GUIDE Systems Engineering & Management Company 1430 Vantage Court Vista, California 92081 PROPRIETARY INFORMATION THE INFORMATION CONTAINED IN THIS DOCUMENT CONSTITUTES

More information

TEMPO USB MICROPHONE

TEMPO USB MICROPHONE TEMPO USB MICROPHONE Congratulations on your purchase of the MXL Tempo USB microphone. MXL microphones are the result of worldclass engineering and manufacturing capabilities. They are designed to provide

More information

RAM-34 RX Pre-amplifier System Installation and Operation Manual

RAM-34 RX Pre-amplifier System Installation and Operation Manual RAM-34 RX Pre-amplifier System Installation and Operation Manual ( www.hamation.com ) RAM-34 Front and Rear Views Introduction The RAM-34 is a complete pre-amplifier system designed primarily for the low

More information

Contents. Saffire PRO 10 i/o. User Guide. Changes to Version 1. Additional Info. Hardware Monitoring Digital Output Monitoring...

Contents. Saffire PRO 10 i/o. User Guide. Changes to Version 1. Additional Info. Hardware Monitoring Digital Output Monitoring... Contents Hardware Monitoring... 2 Digital Output Monitoring... 3 Digital Inputs and Sync Source Selection... 3 Changes to Version 1 Using Multiple Units on a PC... 3 Additional Info Setting up Multiple

More information

FM RADIO TRANSMITTER

FM RADIO TRANSMITTER FM RADIO TRANSMITTER Instruction Manual i702 Please read this manual carefully before operating and save it for future reference. Questions? Please visit http://www.i-luv.com CONTENTS INTRODUCTION General

More information

RMV25 / RMV50 RMU25 / RMU45

RMV25 / RMV50 RMU25 / RMU45 RMV25 / RMV50 RMU25 / RMU45 Owner's Manual TABLE OF CONTENTS INTRODUCTION... 3 FCC Requirements... 3 SAFETY WARNING INFORMATION... 3 CONTROLS and INDICATORS... 5 FRONT PANEL... 5 LCD Icons and Indicators...

More information

Dante. Dante Network Class D Professional Audio Amplifier D-3000

Dante. Dante Network Class D Professional Audio Amplifier D-3000 Dante TM Dante Network Class D Professional Audio Amplifier D-3000 SUMMARY The D-3000 is a high power professional amplifier specially designed for the sound re-enforcement market also referred to as SR,

More information

WEB I/O. Wireless On/Off Control USER MANUAL

WEB I/O. Wireless On/Off Control USER MANUAL Wireless On/Off Control Technical Support: Email: support@encomwireless.com Toll Free: 1 800 617 3487 Worldwide: (403) 230 1122 Fax: (403) 276 9575 Web: www.encomwireless.com Warnings and Precautions Warnings

More information

AirScope Spectrum Analyzer User s Manual

AirScope Spectrum Analyzer User s Manual AirScope Spectrum Analyzer Manual Revision 1.0 October 2017 ESTeem Industrial Wireless Solutions Author: Date: Name: Eric P. Marske Title: Product Manager Approved by: Date: Name: Michael Eller Title:

More information

Apogee Ensemble Thunderbolt Audio Interface

Apogee Ensemble Thunderbolt Audio Interface Apogee Ensemble Thunderbolt Audio Interface Quick Start Guide Fall 2014 Contents Overview... 3 Introduction...3 Package Contents...4 Ensemble Product Tour...6 Getting Started... 8 System Requirements...8

More information

USB.007 Studio Quality USB Stereo Condenser Mic. User Manual

USB.007 Studio Quality USB Stereo Condenser Mic. User Manual USB.007 Studio Quality USB Stereo Condenser Mic User Manual Congratulations on your purchase of the MXL USB.007 which uses two gold diaphragm capsules in an X/Y pattern for stereo recording. MXL microphones

More information

Getting Started with TrangoLink

Getting Started with TrangoLink Getting Started with TrangoLink Overview: TrangoLink allows you to configure and monitor your EAGLE PLUS, FALCON, or PTZ-900 transmitters and receivers. On the EAGLE PLUS and FALCON transmitters, you can

More information

System Power Amplifier (SPA)

System Power Amplifier (SPA) System Power Amplifier (SPA) Installation Guide SPA-60 Amplifi er Amplifi er EXPLANATION OF SYMBOLS The term WARNING! indicates instructions regarding personal safety. If the instructions are not followed

More information

MPR kHz Reader

MPR kHz Reader MPR-5005 Page 1 Doc# 041326 MPR-5005 125kHz Reader Installation & Operation Manual - 041326 MPR-5005 Page 2 Doc# 041326 COPYRIGHT ACKNOWLEDGEMENTS The contents of this document are the property of Applied

More information

User Guide. Version 1.0.

User Guide. Version 1.0. User Guide Version 1.0 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 3 Box Contents...4 Hardware Features...4

More information

MA40E Mini Amplifier with DSP

MA40E Mini Amplifier with DSP MA40E Mini Amplifier with DSP Clearly better sound MA40E Front Panel MA40E Rear Panel General Description The MA40E is a very compact stereo amplifier of advanced design, intended for integration into

More information

Apogee Ensemble Thunderbolt Audio Interface

Apogee Ensemble Thunderbolt Audio Interface Apogee Ensemble Thunderbolt Audio Interface Quick Start Guide July 2017 Contents Overview... 3 Introduction...3 Package Contents...4 Ensemble Product Tour...6 Getting Started... 8 System Requirements...8

More information

MICROWAVE FREQUENCY SYNTHESIZER QP-FSPLL USER MANUAL

MICROWAVE FREQUENCY SYNTHESIZER QP-FSPLL USER MANUAL MICROWAVE FREQUENCY SYNTHESIZER QP-FSPLL-0040-01 USER MANUAL The QP-FSPLL-0040-01 is a low-phase noise wideband synthesizer operating from 50 MHz to 40 GHz with a nominal output power of +15 dbm. The synthesizer

More information

This is by far the most ideal method, but poses some logistical problems:

This is by far the most ideal method, but poses some logistical problems: NXU to Help Migrate to New Radio System Purpose This Application Note will describe a method at which NXU Network extension Units can aid in the migration from a legacy radio system to a new, or different

More information

Programming Parameters - Feature Comparison : Rev 1

Programming Parameters - Feature Comparison : Rev 1 Secure Wireless Microphone ELITE PRO CLASSIC Programming Parameters - Feature Comparison : Rev 1 How to use Programmer: Start Programming application Runs On PC or Mac running Windows 7/8. To put Handset

More information

M-16DX 16-Channel Digital Mixer

M-16DX 16-Channel Digital Mixer M-16DX 16-Channel Digital Mixer Workshop Using the M-16DX with a DAW 2007 Roland Corporation U.S. All rights reserved. No part of this publication may be reproduced in any form without the written permission

More information

M-300 Mono power amplifier User s guide

M-300 Mono power amplifier User s guide M-300 Mono power amplifier User s guide M-300 Mono power amplifier User s guide Specifications: Contents: Power output: 8Ω: 290W, 0.01% THD SPECIFICATIONS Page 2 Input impedance: Gain: 4Ω: 580W, 0.01%

More information

Portable Multi-Channel Recorder Model DAS240-BAT

Portable Multi-Channel Recorder Model DAS240-BAT Data Sheet Portable Multi-Channel Recorder The DAS240-BAT measures parameters commonly found in process applications including voltage, temperature, current, resistance, frequency and pulse. It includes

More information

Studio Broadcast System

Studio Broadcast System SET UP and USE 1. REGULATORY AND COMPLIANCE STATEMENTS... 3 2. OVERVIEW 2.1 Core Performance Targets 2.2 Specifications 2.3 System Components 2.4 System Block Diagram 3. BP24 UWB BODY PACK TRANSMITTER...

More information

LincView OPC USER GUIDE. Enhanced Diagnostics Utility INDUSTRIAL DATA COMMUNICATIONS

LincView OPC USER GUIDE. Enhanced Diagnostics Utility INDUSTRIAL DATA COMMUNICATIONS USER GUIDE INDUSTRIAL DATA COMMUNICATIONS LincView OPC Enhanced Diagnostics Utility It is essential that all instructions contained in the User Guide are followed precisely to ensure proper operation of

More information

Benchmark DAC3 B Instruction Manual

Benchmark DAC3 B Instruction Manual Benchmark DAC3 B Instruction Manual Reference Stereo PCM and DSD D/A Converter with ESS9028PRO Conversion System (Version 1.x Firmware) Safety Information Fuses CAUTION: FOR CONTINUED FIRE HAZARD PROTECTION

More information

OVEN INDUSTRIES, INC. Model 5C7-362

OVEN INDUSTRIES, INC. Model 5C7-362 OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...

More information

LBI-31807D. Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1. Maintenance Manual. Printed in U.S.A.

LBI-31807D. Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1. Maintenance Manual. Printed in U.S.A. D Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1 Maintenance Manual Printed in U.S.A. This page intentionally left blank 13 PARTS LIST 12 PARTS LIST LBI-31807 11 PARTS LIST 10 SCHEMATIC

More information

BandMaster V Manual. Installation

BandMaster V Manual. Installation BandMaster V Manual Installation Installing and configuring the BM-5 BandMaster V is a simple process. All the configuration process is done from the front panel. Installation and configuration steps are

More information

MINIMUM SYSTEM REQUIREMENTS

MINIMUM SYSTEM REQUIREMENTS Quick Start Guide Copyright 2000-2012 Frontline Test Equipment, Inc. All rights reserved. You may not reproduce, transmit, or store on magnetic media any part of this publication in any way without prior

More information

pêma protea êquipped media amplifier

pêma protea êquipped media amplifier Powered Matrix Processors pêma protea êquipped media amplifier pêma 4125 4250 8125 8250 pêma specifications Features: Powered Processors Ashly Audio s promise to Simplify Integration continues with pêma

More information

Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O

Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O Introduction Many people are using relatively low cost, professional audio interfaces such

More information

AN797 WDS USER S GUIDE FOR EZRADIO DEVICES. 1. Introduction. 2. EZRadio Device Applications Radio Configuration Application

AN797 WDS USER S GUIDE FOR EZRADIO DEVICES. 1. Introduction. 2. EZRadio Device Applications Radio Configuration Application WDS USER S GUIDE FOR EZRADIO DEVICES 1. Introduction Wireless Development Suite (WDS) is a software utility used to configure and test the Silicon Labs line of ISM band RFICs. This document only describes

More information

Boulder W Class A Stereo Power Amplifier

Boulder W Class A Stereo Power Amplifier Boulder 2060 600 W Class A Stereo Power Amplifier Owners Manual V1.0 10/10/97 TABLE OF CONTENTS GETTING STARTED Placement of the 2050 Power amplifier......................................... 1-1 Connecting

More information

LM48821 Evaluation Board User's Guide

LM48821 Evaluation Board User's Guide National Semiconductor Application Note 1589 Kevin Hoskins May 2007 Quick Start Guide from the two amplifiers found on pins OUTR and OUTL, respectively. Apply power. Make measurements. Plug in a pair of

More information

User Guide FFFA

User Guide FFFA User Guide FFFA001255 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...4 System Requirements....4

More information

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. October 2017 R2.0

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. October 2017 R2.0 Customer Programming Software RG-1000e (CPS RG-1000e) User Guide October 2017 R2.0 Table of Contents Table of Contents Foreword 2 Revision history 3 Introduction 4 5 1.1 Software installation 5 1.2 Connecting

More information

Always there to help you. Register your product and get support at AJB4300. Question? Contact Philips.

Always there to help you. Register your product and get support at  AJB4300. Question? Contact Philips. Always there to help you Register your product and get support at www.philips.com/support Question? Contact Philips AJB4300 User manual Contents 1 Important 2 Safety 2 2 Your FM/DAB+ clock radio 3 Introduction

More information

M-Powered Basics Guide

M-Powered Basics Guide M-Powered Basics Guide Version 6.8 for M-Powered Systems on Windows or Macintosh Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support

More information

PowerShare PS604A adaptable power amplifier

PowerShare PS604A adaptable power amplifier Product Description Bose delivers 600 watts for fixed-install applications. Through patented technology, total amplifier power is shared across all output channels, allowing installers the freedom to utilize

More information

Delta 44 Quick Start Guide

Delta 44 Quick Start Guide Delta 44 Quick Start Guide The M-Audio Delta 44 is a high grade professional sound card. When setup properly for use with the SDR- 1000, the results speak for themselves. Unbelievably high dynamic range

More information

TT-208. User s Manual. 300Mps 5.8 GHz. IP Camera Wireless Transmission Kit

TT-208. User s Manual. 300Mps 5.8 GHz. IP Camera Wireless Transmission Kit TT-208 300Mps 5.8 GHz IP Camera Wireless Transmission Kit User s Manual V1.0 02 / 2014 Welcome Thank you for purchasing the TT-208 Wireless Transmission Kit for IP Cameras. This user s manual is designed

More information

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. March 2018 R2.2.1

Customer Programming Software RG-1000e (CPS RG-1000e) User Guide. March 2018 R2.2.1 Customer Programming Software RG-1000e (CPS RG-1000e) User Guide March 2018 R2.2.1 Table of Contents Table of Contents Foreword 3 Revision history 4 Introduction 5 1. RG-1000e Customer Programming Software

More information

DSP AMPLIFIERS DI

DSP AMPLIFIERS DI DATA SHEET DSP AMPLIFIERS THE LATEST GENERATION OF DIGITAL HIGH-PERFORMANCE AMPLIFIERS EN PRODUCT DESCRIPTION The new DI-SERIES digital amplifiers have been developed and manufactured in house by FOHHN

More information

USB Microphone. Marshall Electronics

USB Microphone. Marshall Electronics USB Microphone Marshall Electronics Warranty Marshall microphones are guaranteed against defects in material and workmanship for one year from date of purchase. Should you encounter any problem with this

More information

ADI-100 Interrupter. Operator s Manual. 526 S. Seminole Bartlesville, OK /

ADI-100 Interrupter. Operator s Manual. 526 S. Seminole Bartlesville, OK / ADI-100 Interrupter Operator s Manual 526 S. Seminole Bartlesville, OK 74003 918/336-1221 www.sescocp.com ADI - 100 Interrupter FEATURES Clock Accuracy 100% during GPS lock Clock Drift 30 µsec per degree

More information

Mastr III P25 Base Station Transmitter Tune-up Procedure

Mastr III P25 Base Station Transmitter Tune-up Procedure Mastr III P25 Base Station Transmitter Tune-up Procedure 1. Overview The Mastr III Base Station transmitter alignment is performed in several steps. First, the Transmit Synthesizer module is aligned to

More information

Occupancy Sensor OCS 100W Setup Guide

Occupancy Sensor OCS 100W Setup Guide Sensor OCS 100W Setup Guide The OCS 100W is a wall-mounted occupancy sensor that incorporates ultrasonic (US) and passive infrared (PIR) into a dual technology sensor. The US sensor emits ultrasonic sound

More information

Benchmark LA4 Instruction Manual. Reference Stereo Line Amplifier with Relay Gain and Input Control

Benchmark LA4 Instruction Manual. Reference Stereo Line Amplifier with Relay Gain and Input Control Benchmark LA4 Instruction Manual Reference Stereo Line Amplifier with Relay Gain and Input Control Safety Information Fuses CAUTION: FOR CONTINUED FIRE HAZARD PROTECTION ALWAYS REPLACE THE FUSES WITH THE

More information

MC450/MC650 (MC750) OPERATING INSTRUCTIONS

MC450/MC650 (MC750) OPERATING INSTRUCTIONS MC450/MC650 (MC750) OPERATING INSTRUCTIONS MC 2 AUDIO Ltd., Units 6 & 7 Kingsgate, Heathpark Industrial Estate, HONITON, Devon EX14 1YG England Tel: ++(0)1404.44633 Fax: ++(0)1404.44660 www.mc2-audio.co.uk

More information

AT-D868UV CodePlug Programming Guide

AT-D868UV CodePlug Programming Guide INTRODUCTION The AnyTone D868UV radio is a VHF and UHF radio with both Digital DMR (Tier I and II) and Analog capabilities. It offers a total of 4,000 channels (Analog and Digital), 10,000 Digital Talk

More information

RadioStar FST RadioStar FST-5270 Inputs and Outputs Document T15226 Issue 15 Sheet 1

RadioStar FST RadioStar FST-5270 Inputs and Outputs Document T15226 Issue 15 Sheet 1 RadioStar FST-5270 RadioStar FST-5270 Inputs and Outputs Document T15226 Issue 15 Sheet 1 Document ID T/15226 Document Control Document Name Security Circulation Prepared By Reviewed By FST-5270 Inputs

More information

Side view View from below Rear view

Side view View from below Rear view Dimension diagrams All dimensions in mm Side view View from below Rear view Cut out: 138 +0,8 x 138 +0,8 mm Typical connection SPS SPS 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 DSUB-9 5 4 3 2 1 8 7 6 5 4

More information

I n s ta l l at i o n M a n u a l f o r T E D P r o H o m e T E D P r o L i t e A B C Rev 4.0

I n s ta l l at i o n M a n u a l f o r T E D P r o H o m e T E D P r o L i t e A B C Rev 4.0 I n s t a l l a t i o n M a n u a l f o r T E D P r o H o m e T E D P r o L i t e A B C Rev 4.0 IMPORTANT: The installation of your TED Pro Home system is a several-step process. The 1st step is the installation

More information

WDMX-512. user manual

WDMX-512. user manual WDMX-512 user manual Measurements are in millimeters. WDMX512 Standard model 195 50 125 223 436 44 482 182 WDMX512 ProDiversity model 2003 Martin Professional A/S, Denmark. All rights reserved. No part

More information

AW2400iTR USER S MANUAL 2.4 GHz Indoor Wireless Ethernet Radio

AW2400iTR USER S MANUAL 2.4 GHz Indoor Wireless Ethernet Radio USER S MANUAL 2.4 GHz Indoor Wireless Ethernet Radio Industrial-grade, long-range wireless Ethernet systems AvaLAN W I R E L E S S Thank you for your purchase of the AW2400iTR Indoor Wireless Ethernet

More information

AX6220Z/AX6240Z. Energy-Efficient, DSP-Powered and Ethernet/USB-Controlled 1000/900-Watt 70/100 V High-Impedance Power Amplifier.

AX6220Z/AX6240Z. Energy-Efficient, DSP-Powered and Ethernet/USB-Controlled 1000/900-Watt 70/100 V High-Impedance Power Amplifier. Features Ultra-reliable, dual-channel 2*500/2*900-Watt power amplifier with 70/100 V technology, designed for continuous operation in distributed music, paging and AV applications State-of-the-art, energy-saving

More information

SETUP and OPERATING MANUAL ADVANCED MULTI-CHANNEL VEHICLE INTERCOM SYSTEM (AMCVIS)

SETUP and OPERATING MANUAL ADVANCED MULTI-CHANNEL VEHICLE INTERCOM SYSTEM (AMCVIS) SETUP and OPERATING MANUAL Sept 23, 2010 Rev D ADVANCED MULTI-CHANNEL VEHICLE INTERCOM SYSTEM (AMCVIS) with DIGITAL CREW CONTROL and RADIO BRIDGING The AMCVIS was designed, manufactured and is supported

More information

ASTRO 25. Single Transmit Site, Multiple Receiver Voting Subsystem. Trunked Integrated Voice and Data System Release 6.9/7.2 * Y29* Y29-A

ASTRO 25. Single Transmit Site, Multiple Receiver Voting Subsystem. Trunked Integrated Voice and Data System Release 6.9/7.2 * Y29* Y29-A ASTRO 25 Trunked Integrated Voice and Data System Release 6.9/7.2 Single Transmit Site, Multiple Receiver Voting Subsystem *6881014Y29* 6881014Y29-A 2006 Motorola, Inc. All rights reserved. December 2006

More information

MA6480A. Energy-Efficient, Multi-Function 240-Watt Mixing Amplifier with Dual 70/100 V and 4 Ohms Outputs. Features

MA6480A. Energy-Efficient, Multi-Function 240-Watt Mixing Amplifier with Dual 70/100 V and 4 Ohms Outputs. Features Features Multi-function 240-Watt mixing amplifier with dual 70/100 V and 4 Ω outputs, designed for continuous operation in distributed music, paging and AV applications State-of-the-art, energy-saving

More information

Telex. User Instructions. Model SPS2000A Power Supply Audiocom Intercom Systems SPS2000A. Volume RESET

Telex. User Instructions. Model SPS2000A Power Supply Audiocom Intercom Systems SPS2000A. Volume RESET R Telex User Instructions SPS000A RESET Volume Model SPS000A Power Supply Audiocom Intercom Systems FCC Statement This equipment uses, and can radiate radio frequency energy that may cause interference

More information

MFJ-1272M TNC/MICROPHONE SWITCH

MFJ-1272M TNC/MICROPHONE SWITCH TNC/MICROPHONE SWITCH Introduction Thank you for purchasing the TNC/MIC Switch. The is designed to allow simultaneous connection of both your microphone and your TNC to the radio. The microphone switches

More information

BRU-100 Physical Installation

BRU-100 Physical Installation APPENDIX B BRU-100 In This Appendix: Warnings and Cautions, page 50, page 51 Check List, page 57 This appendix provides guidance for the physical installation of the BRU-100 Remote Unit at a subscriber

More information

Copyright 1996 Codan Pty Ltd.

Copyright 1996 Codan Pty Ltd. No part of this handbook may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Pty Ltd. Copyright 1996 Codan Pty

More information