INSTALLATION INSTRUCTION Supersedes: N1.8Y (399) N1.8Y (699)

Size: px
Start display at page:

Download "INSTALLATION INSTRUCTION Supersedes: N1.8Y (399) N1.8Y (699)"

Transcription

1 MILLENNIUM HEAD PRESSURE CONTROL KIT FOR LOW AMBIENT APPLICATIONS INSTALLATION INSTRUCTION Supersedes: N.8Y (399) N.8Y (99) HEAD PRESSURE CONTROL FOR 208/230 & 0V 25, 30 & 0 TON MILLENNIUM UNITS DESCRIPTION These units are only designed to operate at ambient temperatures down to 0 F. This accessory will insure safe operation at ambient temperatures down to 0 F. The Head Pressure Control option controls the speed of condenser fan # for low ambient mechanical cooling operation of systems # and #2. System #3 on a 30 ton and system #3 and # on a 0 ton are locked out below 5 F ambient. TABLE -CONTROL APPLICATION DATA ACCESSORY MODEL NO. 2LA LA07030 TABLE - 2 COMPONENTS SUPPLIED WITH KIT QUANTITY DESCRIPTION Head pressure Control assembly. consisting of: Sheet metal back plate. (HPC assembly back plate) VOLTAGE 208V & 230V 0V 2LA = 208/230 Variable frequency drive, Magnetek 333, Model # DS022 2LD07030 = 0V Variable frequency drive, Magnetek 333, Model # DS02 The option includes two pressure transducers, a proportional integral sequence controller and a one horsepower variable frequency drive. The pressure transducers are connected to the discharge line of system # and #2. Each pressure transducer is equipped with a switching diode on the white signal wire to eliminate feed back through the other transducer. The proportional integral sequence controller (PI controller), provides 3.9 VDC power from terminal "VDC" to each pressure transducer. The transducer has an output signal of 0-0 VDC, which connects to the PI controller at terminal "SN". The PI controller regulates the output signal to the variable frequency drive based on a fixed setpoint of 20 PSI. The output signal from the PI controller is -20ma at the "I" terminal. The input terminal on the variable frequency drive is the "9" terminal. The PI controller will vary the output to maintain a minimum discharge pressure of 20 PSI. The Proportional Integral Sequence controller is factory set for direct acting operation (the signal output increases as the pressure signal increases). DIP switch setting is factory set for C (switch to ON position, all others OFF). This is the fastest integration time available, designed to compensate for extremely rapid rates of change. The Throttling range is factory set to 20 PSIG (adjustable from 0 to 00 PSIG). The minimum output is factory set for 2VDC (20%) which is adjustable from 0 to VDC (0 to 0%). 2 Electronic Proportional Plus Integral Control, Johnson model P352P Refrigerant Pressure Transducer, Johnson model P99 ". + / ) -, +, * ), 2 Diode 2LA = 0VA transformer 230 volt primary and 2 volt secondary. 2LA07030 = 0VA transformer 0 volt primary and 2 volt secondary. Sheet metal cover. 0 F Cooling lockout switch (CLO2), Thermodisc model 37TV Connector Tee 2 Neoprene air seal blocks Wiring Diagram for Head Pressure Control Circuitry ( ), ) / Wire ties and #0 screws + * : FIG. - COOLING LOCKOUT SWITCH LOCATION NOTE: ALTERING THE FACTORY SETTINGS COULD RE- SULT IN POOR CONTROL OR OPERATION OF THE SYS- TEM. No special motor is required on the /0 volt units. The volt variable frequency drive requires single-phase input power and it produces three-phase variable output power

2 N.8Y to condenser fan motor #. The 0-volt variable frequency drive requires three-phase input power and produces threephase variable output power to condenser fan motor #.On the 575-volt and 380volt 0-hertz units a transformer is used to reduce line voltage to 230 volts. This instruction provides all the necessary information to properly field install a low ambient head pressure control on the units indicated above. All of the components required to install this kit are provided in the kit. Refer Table for control application data and Table 2 for the components that are 7 EJ * = I A = E I J = A M A F H A A = EH I A = >? I = B J A H H K J E C J D A J H = K? A H M EH A = C J D A > J J B J D A > = I A H = E + 7 * 0 A 2 H A I I K H A + J H 2! # H = I B H A H. H # % # & 8 J 8., F JE H J H 0 A 2 H A I I K H A 8., 8., FIG 2 - MOUNTING LOCATION OF HEAD PRESSURE CONTROL supplied in the respective accessory. INSTALLATION 2 H A I I K H A H = K? A H. H J H 8., WARNING:To prevent bodily injury or damage to the unit, turn unit power off at the disconnect. INSTALLING THE 0 F COOLING LOCKOUT SWITCH. Mount the 0 F Cooling lockout switch (CLO2) next to the 0 F Cooling lockout switch (CLO) on the condenser bulkhead panel. (see figure ) 2. Feed CLO2 wires through the same bushing used by CLO into the electrical control box. 3. Disconnect wire 259/BL from LOR-A and connect it to LOR2-A.. Remove wire 39/BL between LOR-A and LOR2-A. 5. Connect CLO2 wire to 258/Y for VAV/VFD units or wire 252/Y for CV units and connect 9/BL to LOR-A. ( Refer Fig. 5) INSTALLING THE HEAD PRESSURE CONTROL ASSEMBLY. Locate the X conduit box opposite the control box in the Supply blower section.(fig. 2). The X conduit box provides access to the # condenser fan power wiring. H = K? A H M EH E C B H J D A 2! # 2? J H A H H K J E C J J D EI? D = H C A E A 5 D H A H L = L A B? F H A I I H I FIG. 3 TRANSDUCER WIRE ROUTING 2. Mount the Head pressure Control assembly on the sheet metal panel approximately 2-" to the right of the X conduit box.(fig. 2) 3. Remove the X box cover and pull out the wires. NOTE: Refer to wiring diagram for steps - 7. Disconnect wire 9/BK from wire /BK. 5. Connect wire 9/BK to T/.. Connect wire /BK to L/R. 7. Disconnect wire 92/Br from wire 7/BR. 8. Connect wire 92/BR to T2/V. 9. Connect wire 7/BR to L2/S. 0. Disconnect wire 93/PR from wire 8/PR.. Connect wire 93/PR to T3/W. 2. Connect wire 8/PR to L3/T. 3. Disconnect ground wires 82 and 83 from one another.. Connect ground wire 82 to G/E. 5. Connect ground wire 83 to G/E. INSTALLING THE PRESSURE TRANSDUCERS. Remove both pressure transducers from their shipping position on the sheet metal cover. CAUTION: Do not remove the plastic plugs from the transducers until they are ready to connect to the shrader tees. 2. Remove Neoprene air seal blocks (See figure 3). 3. Route the pressure transducers along the inside bottom of the base rail channel to the compressor discharge lines.(see Fig.3). Replace neoprene air seal blocks. 5. Install each pressure transducer to a tee connector using Red Loctite #55 thread sealant (for use with R22 refrigerant systems). To ensure a proper seal, install the flare gasket shown in Figure.. Install one tee connector (with the transducer) on the spare shrader fitting located on the #compressor discharge line 2 York International

3 2 ' ' ) 5, using Red Loctite #55 thread sealant (for use with R22 refrigerant systems). NOTE: The pressure transducers are connected in parallel at the controller, therefore it does not make a difference which transducer is installed on system # or #2. 7. Install the other tee connector (with the transducer) on the spare shrader fitting located on the #2 compressor discharge line using Red Loctite #55 thread sealant (for use with R22 refrigernat systems). TESTING. Connect a pressure gauge to the discharge line of compressor #. 2. Connect a pressure gauge to the discharge line of compressor #2. 3. Restore power to the unit.. Observe condenser fan operation upon a call for first stage cooling. 5. Check condenser fan # for proper rotation.. ) - / ) FIG. PRESSURE TRANSDUCER INSTALLATION N.8Y. Monitor discharge pressure on system # and #2, the P352P controller will try to maintain a pressure of 225-PSI +/- 20 PSI. Sequence of Operation A call for first stage cooling powers the M contactor powering the variable frequency drive. The drive will ramp to the preprogrammed minimum speed of 0 hertz immediately upon start up. The drive is preprogrammed for a minimum speed at 0 hertz and a maximum speed at 0 hertz. As the discharge pressure rises above 20 PSI during start up on system # or #2 compressor, then the PI controller will increase the output signal to the variable frequency drive. The drive will increase the speed of condenser # fan accordingly. The scroll compressor produces a rapid rise in discharge pressure upon start up and this, most often times, will result in full speed operation of condenser fan #. After the discharge pressure has settled out, the speed of condenser # may decrease especially during times when the ambient temperature is below 80 F. After the # system has stabilized and compressor #2 is energized, usually the speed on condenser fan # will increase, compensating for the discharge pressure rise. As the discharge pressure begins to fall below the 20 PSI setpoint, the drive will reduce the speed of condenser fan #. As the ambient temperature drops below 0 F the # condenser fan will slow to the minimum speed. The #2 condenser fan will disengage when the discharge pressure drops below 80 PSIG as the ambient temperature falls. The discharge pressure of system # and/or #2 will increase when condenser fan #2 is disengaged. PROBLEM POSSIBLE CAUSE / SOLUTION ) 2) Discharge pressure is high, condenser fan # RPM is slow. Variable frequency drive is operating at 0 hertz (read out on display) with high discharge pressure.. 2. Check pressure transducer connections at the P352 controller, white wire connects to terminal "SN", brown wire connects to terminal "VDC" and the green wire connects to TB9. Check diode on the transducer signal wire (white) for correct position. The cathode end (visible band at the end of the diode) should face toward the wire end, away from the transducer. 3. Check power to the P352 controller at the 2 VDC and COM terminals.. Check connection from P352 controller to the variable frequency drive. 5. Check transducer connection. Valve depressor may not be contacting/depressing the valve core. Check to ensure the transducer has VDC power to it on the brown wire from the P352 controller terminal VDC. Check the voltage out from the transducer on the white wire. Voltage should be above VDC. 3) Condenser fan operates in the reverse direction.. Power leads to drive (VFD) are phased improperly. Switch any two leads. ) Condenser fan motor does not operate.. Check power to the drive. 2. Power leads to drive may be reversed. Wires 9, 92 and 93 should connect to U/T, V/T2, and W/T3. Wires, 7 and 8 should connect to L/R, L2/S, and L3/T. NOTE: If the power lead (, 7 and 8) from the contactors are connected to U/T2, V/T2, and W/T3, the drive will be permanently damaged. York International 3

4 ; 2 ), * / 5 ' * * ; -!, * 9 - %! % " % # % $ % % % & % ' & 5, - + * : % %! / * " ' *! & 8., *! ' * + 5 ) * + ' $ + - +, ) / ) * % 9 0 * ' " ' # # %!. 7 " # $ * ". 7! ' * # # #. 7! & ; -, * 9-8., ) ;, ) * +, -. / 0! &, * 9 - /, 7 /!! # # #. 7! ' * # $ * ". 7 " # %!. 7 / 5 * 8., 8 ) ) * ;, 8 - / / ' * * ; -! / * " + 5 / N.8Y FIG. 5 - WIRING DIAGRAM * % * 9 0 ' " 8 ) ) * ;, 8 - # $ * ' # CAUTION: OPEN ALL DISCONNECTS BEFORE SERVICING THIS UNIT " # % # # / * / / 035-9D000 REV.A /, 7 /! York International

5 K A + A? J H E E K K J F K J 2 J A J E A J A H D H J J E C = C A 2 J A J E A J A H F A H = J E A K F A H, EHA?J)?JE 2 I EJ E 2 A H? A J B K J F K J E? = J H EC D 8 5 8, + + " 8 J ) K J F K J ' A H E = 8., 7 - : ' ' FIG. - P352P PRESSURE CONTROL York International 5

6 N.8Y York International

7 N.8Y York International 7

8 Unitary Products Group 5005 York Drive, Norman, Oklahoma 7309 Subject to change without notice. Printed in U.S.A. Copyright by York International Corporation 999. All Rights Reserved. SBY N.8Y (99)

Sealed Interface Control: EC20300

Sealed Interface Control: EC20300 ISO 9001:2000 WITH DESIGN Certificate #02.002.1 Sealed Interface Control: EC20300 FEATURES: Weather tight control package Pulse Width Modulated output Waterproof altitude pressure and vapor release vent

More information

April 1994 UCM-420A. Setpoint Controller. Operating and Installation Instructions

April 1994 UCM-420A. Setpoint Controller. Operating and Installation Instructions April TM UCM-A Setpoint Controller Operating and Installation Instructions A LARGE number of applications in a SMALL package... REMOTE SETPOINT CONTROLLER LOCAL SETPOINT CONTROLLER - ma SIGNAL GENERATOR

More information

Quantum LX Motor Current Testing

Quantum LX Motor Current Testing The Quantum LX control panel is capable of reading external analog devices, such as Current transformers (CT) or other external devices, such as a VFD. It uses these input signals for the purpose of monitoring

More information

Electronically Commutated (EC) Motor Control with Solo, Select and Sync PWM Boards

Electronically Commutated (EC) Motor Control with Solo, Select and Sync PWM Boards Electronically Commutated (EC) Motor Control with Solo, Select and Sync PWM Boards The Solo, Select and Sync PWM boards provide a pulse-width modulated (PWM) signal to the EC motor to control fan speed.

More information

Evolution. EC Motor Series 1. Automation Interface CONTROLS INC. EVO /ECM-ACU+ Application. Ordering

Evolution. EC Motor Series 1. Automation Interface CONTROLS INC. EVO /ECM-ACU+ Application. Ordering Evolution Automation Interface COTROLS IC. EVO /ECM-ACU+ EC Motor Series 1 Application The allows industry standard 0V to +10V automation signals to adjust and monitor EC Motors. These are fractional horsepower

More information

SINPAC Switches: Brief Operating Description. Mounting Options

SINPAC Switches: Brief Operating Description. Mounting Options SINPAC Switches: Brief Operating Description For over 75 years, single-phase motors have utilized a mechanical centrifugal switch to switch the start circuit. Inherent characteristics of a mechanical device

More information

SixPac Series of SCR AC Controller and DC Converters

SixPac Series of SCR AC Controller and DC Converters SixPac Series of SCR AC Controller and DC Converters Complete Series of SCR Three-Phase Power Control Units Features Include: Compact, rugged construction Applications include: Windmill Converters Motor

More information

Optidrive Applications Support Library

Optidrive Applications Support Library Optidrive Applications Support Library Application Note Title AN-ODE-2-032 Related Products Optidrive E2 Overview Level 2 PI Closed Loop Feedback Control Applications 1 Fundamental - No previous experience

More information

(267 kw THROUGH 735 kw)

(267 kw THROUGH 735 kw) YCWS (HFC-407C) 50 HZ WATER COOLED LIQUID CHILLERS INSTALLATION, OPERATION AND MAINTENANCE New Release Form 201.24-NM2.1 (202) YCWS WATER COOLED LIQUID CHILLERS YCWS0313SB 0663SB (ADDENDUM FOR HFC-407C

More information

HLC-1000 High-limit Humidity Control

HLC-1000 High-limit Humidity Control FANs 216, 1628.3 Product/Technical Bulletin HLC-1000 Issue Date 1197 HLC-1000 High-limit Humidity Control The HLC-1000 is designed to limit duct humidity by comparing a controller s request for humidification

More information

PARTS LIST FOR MODEL 7000 SERIES - 17/46

PARTS LIST FOR MODEL 7000 SERIES - 17/46 ITEM PARTS LIST FOR MODEL 7000 SERIES - 17/46 1 Rotor 3 Housing 1 4 End Plate 6 Drive End Cover 1 7 Free End Cover 1 8 Timing Gear Set 1 9 Bearing, Drive End 10 Bearing, Free End 1 Lip Seal, Viton 4 13

More information

Technical Information

Technical Information Date of last update: Aug-14 Ref: REFRIGERATION - CONTROLLING DIGITAL SCROLL Application Engineering Europe 1 Introduction Refrigeration applications such as retail and convenience stores are requesting

More information

PWM. Design, Installation, and Operation. (Pulse Width Modulation Zone Controller)

PWM. Design, Installation, and Operation. (Pulse Width Modulation Zone Controller) Small Duct Heating, Cooling and Indoor Air Quality Systems www.hi-velocity.com TM PWM (Pulse Width Modulation Zone Controller) Design, Installation, and Operation Includes: PWM Design PWM Installation

More information

SmartZone-2 & SmartZone-4

SmartZone-2 & SmartZone-4 SmartZone-2 & SmartZone-4 Quick-Start Guide UPDATED 2011-7-26 This guide is intended to give the installer a brief set of instructions about how to set up the XCI Zoning SmartZone System. For more detailed

More information

Potentiometer Control EC20200

Potentiometer Control EC20200 Engineering & Manufacturing Solutions Potentiometer Control EC20200 APPLICATION: Proportionally control the speed of hydraulic motors and cylinders. ISO 9001:2008 WITH DESIGN Certificate #02.002.1 Features

More information

The MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. The main is drilled out under pressure.

The MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. The main is drilled out under pressure. MUELLER SMALL DRILLING MACHINES 2.1 Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines are available in hand

More information

EXPLODED VIEW OF KINNEY MODELS KC-5 & KC-8

EXPLODED VIEW OF KINNEY MODELS KC-5 & KC-8 EXPLODED VIEW OF KINNEY MODELS KC-5 & KC-8 KC-5 KC-8 Pump RPM 638 1022 Motor HP (kw) 0.33 (0.25) 0.50 (0.37) Oil Capacity, qts. (liters) 0.8 (0.76) Forced Drain w/ open suction, qts. (liters) 0.85 (0.80)

More information

Installation of Fillmaster DuraBlue Melters. System on. Introduction. Instruction Sheet P/N B

Installation of Fillmaster DuraBlue Melters. System on. Introduction. Instruction Sheet P/N B Instruction Sheet P/N 1047806B Installation of Fillmaster DuraBlue Melters System on WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment. The use

More information

Optional end of travel limit switches for user setting of minimum and maximum pressure values.

Optional end of travel limit switches for user setting of minimum and maximum pressure values. A M/P Converters Features (Varies with s) AC Control Unit (CC) Output pressure locks in last position in event of power failure. Continuous AC Motor unit is instant start-stop, heavy duty impedance protected

More information

Optional end of travel limit switches for user setting of minimum and maximum pressure values.

Optional end of travel limit switches for user setting of minimum and maximum pressure values. A M/P Converters Features (Varies with s) AC Control Unit (CC) Output pressure locks in last position in event of power failure. Continuous AC Motor unit is instant start stop, heavy duty impedance protected

More information

PARTS LIST ELECTRIC BOILERS MODELS: CE24 CE36 CE42 CE48 CE324 CE336 CE342 CE348

PARTS LIST ELECTRIC BOILERS MODELS: CE24 CE36 CE42 CE48 CE324 CE336 CE342 CE348 PARTS LIST ELECTRIC BOILERS MODELS: CE24 CE36 CE42 CE48 CE324 CE336 CE342 CE348 CROWN FOOD SERVICE EQUIPMENT LTD. 70 OAKDALE ROAD, DOWNSVIEW, (TORONTO), ONTARIO, CANADA, M3N 1V9 TELEPHONE: (416) 746-2358,

More information

MUELLER GAS. DH-5 Drilling Machine. For use on 1 1 /2 & 2 Line Stopper Fittings. Reliable Connections. General Information 2

MUELLER GAS. DH-5 Drilling Machine. For use on 1 1 /2 & 2 Line Stopper Fittings. Reliable Connections. General Information 2 operating Instructions manual MUELLER GAS TAble of contents PAGE DH-5 Drilling Machine For use on 1 1 /2 & 2 Line Stopper Fittings General Information 2 Installing and Stopping-off 1 1 /2 and 2 Line Stopper

More information

PA FAN PLATE ASSEMBLY 188D6127G1 SYMBOL PART NO. DESCRIPTION. 4 SBS /10 Spring nut. 5 19A702339P510 Screw, thread forming, flat head.

PA FAN PLATE ASSEMBLY 188D6127G1 SYMBOL PART NO. DESCRIPTION. 4 SBS /10 Spring nut. 5 19A702339P510 Screw, thread forming, flat head. MAINTENANCE MANUAL 851-870 MHz, 110 WATT POWER AMPLIFIER 19D902797G5 TABLE OF CONTENTS Page DESCRIPTION.............................................. Front Page SPECIFICATIONS.................................................

More information

The MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. Hand or power. kpa/34.

The MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. Hand or power. kpa/34. MUELLER SMALL DRILLING MACHINES 2.1 Shaded area indicates change Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines

More information

GUIDE SPECIFICATIONS CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP GENERAL DESCRIPTION

GUIDE SPECIFICATIONS CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP GENERAL DESCRIPTION GUIDE SPECIFICATIONS 256920-UGS-A-0506 Simplicity Intelli-Comfort Optional Control in 3-25 Ton Packaged Units GENERAL DESCRIPTION CONTROLS SPECIFICATIONS AND CONTROL POINT DATA MAP Equipment with Simplicity

More information

INSTRUCTION MANUAL G EN1000/EN1001 CASCADE/MULTI-VALVE SERIES CONTROLS

INSTRUCTION MANUAL G EN1000/EN1001 CASCADE/MULTI-VALVE SERIES CONTROLS INSTRUCTION MANUAL 700194G EN1000/EN1001 CASCADE/MULTI-VALVE SERIES CONTROLS MICROPROCESSOR BASED Weld Sequence Controls With Solid State Thyristor Contactors Wiring Diagrams Cabinet Style EN1000 EN1001

More information

H2-50 Hydrogen Generator Field Update

H2-50 Hydrogen Generator Field Update This field update is intended to provide extra protection in the event the H2 generation cell fractures or cracks. Please add the additional parts to your H2-50 as soon as possible. Please take a digital

More information

Model 2400 Explosion-Proof M/P Converters -- LOCK IN LAST POSITION --

Model 2400 Explosion-Proof M/P Converters -- LOCK IN LAST POSITION -- A Explosion-Proof M/P Converters -- LOCK IN LAST POSITION -- Electrical AC Control Unit Motor Voltage...115vAC, 60Hz Power Consumption (watts) 10 Regulator...5(Max.) 16 Regulator...3(Max.) 80 Regulator...3(Max.)

More information

AWUF Series. Wall-Mount Air Handler 1½ to 3 Tons. Contents. Product Features

AWUF Series. Wall-Mount Air Handler 1½ to 3 Tons. Contents. Product Features Series Wall-Mount Air Handler 1½ to 3 Tons Contents Nomenclature...2 Accessories...2 Product Specifications...3 Dimensions...6 Airflow Data...8 Wiring Diagram...9 Product Features Equipped with a Check

More information

YD (MOD A-C) WITH OPTIVIEW CONTROL CENTER FIELD CONTROL MODIFICATIONS

YD (MOD A-C) WITH OPTIVIEW CONTROL CENTER FIELD CONTROL MODIFICATIONS Supersedes: 160.69-PW2 (815) Form 160.69-PW2 (116) WIRING DIAGRAM CONTRACTOR ORDER NO. JCI CONTRACT NO. JCI ORDER NO. YD (MOD A-C) WITH OPTIVIEW CONTROL CENTER FIELD CONTROL MODIFICATIONS PURCHASER JOB

More information

PRESSURE REGULATORS PARKER PRESSURE REGULATING VALVES PRESSURE REGULATORS

PRESSURE REGULATORS PARKER PRESSURE REGULATING VALVES PRESSURE REGULATORS PARKER PRESSURE REGULATING VALVES For R-22, R-502, R-404A, R-507 and other common refrigerants Pilot operated for close control at desired set point. Long life diaphragms. No bellows to fail. Lightweight

More information

FW / FIG Partition Kit(s) Installation Instructions

FW / FIG Partition Kit(s) Installation Instructions FW / FIG Partition Kit(s) Installation Instructions This instruction explains how to join 8 in. and 10 in. top piping partitions to FIG and FW merchandisers. Do not remove the shipping braces until the

More information

FA-3300 Heavy Duty Electric Actuator. Features and Benefits. FA-3300 Actuator with VG8000 valve. Constant running time. Fixed close-off force.

FA-3300 Heavy Duty Electric Actuator. Features and Benefits. FA-3300 Actuator with VG8000 valve. Constant running time. Fixed close-off force. European Electronic Controls Catalogue Section E Product Bulletin FA-3300 Issue Date 0998 FA-3300 Heavy Duty Electric Actuator I ntroduction The FA-3300 series synchronous motor-driven, reversible, heavy

More information

30AUTO Speed Lathe Manual

30AUTO Speed Lathe Manual 30AUTO Speed Lathe Manual Standard Features 3/4 HP Motor Air-Collet Closure 1800 RPM, Single Speed Electric Brake Cast Housing 5C Collets 3 Phase / 240 Volts DESCRIPTION: The Crozier Model 30AUTO Automotive

More information

MM1/MM2 CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS THE FUTURE OF CONTROL TM

MM1/MM2 CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS THE FUTURE OF CONTROL TM THE FUTURE OF CONTROL TM MM1/MM CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS 317-335-60 P.O. Box 18 McCordsville, Indiana 46055 www.proportionair.com FEATURES Universal Mounting Din Rail,

More information

University of Houston Master Construction Specifications Insert Project Name SECTION MECHANICAL SCOPE OF WORK PART 1 - GENERAL

University of Houston Master Construction Specifications Insert Project Name SECTION MECHANICAL SCOPE OF WORK PART 1 - GENERAL SECTION 23 00 10 - MECHANICAL SCOPE OF WORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section 23 01

More information

Conic Systems Inc. INSTRUCTION MANUAL FOR DATATRAN C2547 UNIVERSAL AMPLIFIER MODULE

Conic Systems Inc. INSTRUCTION MANUAL FOR DATATRAN C2547 UNIVERSAL AMPLIFIER MODULE Conic Systems Inc. INSTRUCTION MANUAL FOR DATATRAN C2547 UNIVERSAL AMPLIFIER MODULE FOR TECHNICAL OR SALES ASSISTANCE CONTACT CONIC SYSTEMS INC. AT TEL: 845.856.4313 OR FAX: 845.858.2824 EMAIL: INFO@CONICSYSTEMS.COM

More information

THE FUTURE OF CONTROLTM MM1/MM2 CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS

THE FUTURE OF CONTROLTM MM1/MM2 CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS THE FUTURE OF CONTROLTM MM1/MM CONTROL VALVES CLOSED LOOP PROPORTIONAL PRESSURE CONTROLS 317-335-60 P.O. Box 18 McCordsville, Indiana 46055 www.proportionair.com FEATURES Universal Mounting Din Rail, Panel

More information

BENCHTOP PRESSURE CONTROLLER USER MANUAL

BENCHTOP PRESSURE CONTROLLER USER MANUAL Engineering Your Success BENCHTOP PRESSURE CONTROLLER USER MANUAL Parker Hannifin Corporation Precision Fluidics Division 26 Clinton Drive Unit 103 Hollis, NH, 03049 USA Phone 603-595-1500 GENERAL DESCRIPTION

More information

Power Output. Spindle. 7.7 Inches (196 cm) 11.0 Lbs. (5.0 Kg)

Power Output. Spindle. 7.7 Inches (196 cm) 11.0 Lbs. (5.0 Kg) HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual SUPER HEAVY DUTY VERTICAL GRINDERS 4 Horsepower Vertical Grinders 4 HORSEPOWER Model Number Throttle Type Power Output Weight

More information

Rhino Packing Gland Tool

Rhino Packing Gland Tool Instruction Sheet P/N Rhino Packing Gland Tool 1. Description See Figure 1. The Rhino packing gland tool is used to remove the packing gland from Rhino bulk unloader pumps. The tool consists of two components,

More information

BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide

BL-ER-P Ethernet Radio Unit for Pedestal Installation Guide Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem

More information

Digital Interface Card DEC005000

Digital Interface Card DEC005000 Engineering & Manufacturing Solutions Digital Interface Card DEC005000 APPLICATION: The DEC005000 conveniently interfaces industry standard signals 4-20mA, 0-5V or 0-10V with a proportional solenoid valve

More information

BFS / BFSM SERIES Installation & Maintenance Manual

BFS / BFSM SERIES Installation & Maintenance Manual Introduction: The BFS / BFSM series electric actuators have battery backup modules for fail safe operation. The BFS series is for two position control and the BFSM series is for proportional control, both

More information

Direct solenoid and solenoid pilot operated valves

Direct solenoid and solenoid pilot operated valves Direct solenoid and solenoid pilot operated valves Series 5 Individual mounting Series Inline Bonded spool Air return Manual operator Solenoid 4-way pilot with balanced poppet 33 34 36 3 37 38 5 67 69

More information

Series R48 Single Zone Load Sequenced Economizer System: Installation & Troubleshooting

Series R48 Single Zone Load Sequenced Economizer System: Installation & Troubleshooting FANs 216, 121 Technical Bulletin R48 Issue Date 0695 Series R48 Single Zone Load Sequenced Economizer System: Installation & Troubleshooting Table of Contents Mounting... 1 Output Control... 2 Wiring...

More information

Merloni Elettrodomestici. Technical Fitting Manual FRIDGE. Language Issue/Edition Page GB /

Merloni Elettrodomestici. Technical Fitting Manual FRIDGE. Language Issue/Edition Page GB / GB 99-11-03/01 1-38 Index 1 CONFORMITY OF APPLIANCE 3 2 MAIN ASSEMBLY TYPES 3 2.1 Under worktop 3 2.2 Double door 10 2.3 Combined 14 2.4 Single door Fridge or single door Freezer 19 2.5 Combined free-standing

More information

Z 406 Bench work Manual

Z 406 Bench work Manual 08686 Z 406 Bench work Manual Rev A Custodian: Brian Simeone Table of Contents Section Gantry Removal & Replacements Page 1.. Remove & Replace Printer Module.......3 2.. Remove & Replace Head Card Assembly.....

More information

500mA Laser Diode Controller

500mA Laser Diode Controller IP500 500mA Laser Diode Controller Operating Manual THORLABS, Inc. Ph: (973) 579-7227 435 Route 206N Fax: (973) 300-3600 Newton, NJ 07860 USA www.thorlabs.com Table of Contents TABLE OF FIGURES 1 OVERVIEW

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Restrictor Orifice Coils These instructions must be read and understood completely before attempting installation. It is important that the Blower and Duct System be properly

More information

AU INSTALLATION INSTRUCTIONS. Revision B1 Rapid City, SD, USA, 02/2010 II_201A-AU_B1

AU INSTALLATION INSTRUCTIONS. Revision B1 Rapid City, SD, USA, 02/2010 II_201A-AU_B1 INSTALLATION INSTRUCTIONS Revision B1 Rapid City, SD, USA, 02/2010 MODELS 201A-AU 201-575-AU II_201A-AU_B1 2880 North Plaza Drive, Rapid City, South Dakota 57702 (800) 843-8848 (605) 348-5580 fax (605)

More information

SB 50 Connectors - up to 120 amps

SB 50 Connectors - up to 120 amps Connectors - up to 120 amps Based off the design pioneered by Anderson in 1953, APP s two pole SB connectors set the standard for DC power distribution and battery connections. connectors feature a one

More information

Electronic plugs for valves MSE

Electronic plugs for valves MSE Murrelektronik valve plugs with integrated electronic circuits. Saves time, money and space. Electronics With the Murrelektronik electronic valve plugs, we have made it possible to integrate many different

More information

W7100A-E Discharge Air Controller

W7100A-E Discharge Air Controller W7100A-E W7100A-E Discharge Air Controller The microprocessor based W7100 Discharge Air Controller maintains an average discharge air (DA) temperature in variable air volume (VAV) cooling systems by modulating

More information

DPFHP451 HIGH PERFORMANCE BILEVEL STEP MOTOR / MANUAL PRESET INDEXER DRIVER PACK

DPFHP451 HIGH PERFORMANCE BILEVEL STEP MOTOR / MANUAL PRESET INDEXER DRIVER PACK DPFHP451 HIGH PERFORMANCE BILEVEL STEP MOTOR / MANUAL PRESET INDEXER DRIVER PACK Internal Index Count switches Pulse Rates up to 14,792 pulses per second CW & CCW Home, Hard, & Soft Limit Inputs Adjustable

More information

Excel 10 W7761A Remote Input/Output Device

Excel 10 W7761A Remote Input/Output Device Excel 0 W776A Remote Input/Output Device INSTALLATION INSTRUCTIONS PRODUCT DESCRIPTION The W776A Remote Input/Output (RIO) Device is a Free Topology Transceiver (FTT) LonMark compliant device in the Excel

More information

Servomotor for butterfly valves VF, VFH. delta-elektrogas.com EE157-01/16

Servomotor for butterfly valves VF, VFH. delta-elektrogas.com EE157-01/16 MZ Servomotor for butterfly valves VF, VFH delta-elektrogas.com EE157-01/16 MZ Servomotor Contents Description.... 2 Features........ 2 Functioning and application..... 3 Technical specifications......

More information

AD-8100 & AD-8200 Servo Amplifiers

AD-8100 & AD-8200 Servo Amplifiers Instruction Manual IM-0607 AD-8100 & AD-8200 Servo Amplifiers Table of Contents General Information... 2 Basic Models... 3 Specifications... 3 Installation Wiring... 3 Setup & Calibration... 4-6 Troubleshooting

More information

MUELLER E-5TM. and D-5TM. Drilling Machines. Reliable Connections. E-5 General Information 2. D-5 General Information 3. Operating Instructions 4-5

MUELLER E-5TM. and D-5TM. Drilling Machines. Reliable Connections. E-5 General Information 2. D-5 General Information 3. Operating Instructions 4-5 operation Instructions manual MUELLER E-5TM and D-5TM TAble of contents PAGE E-5 General Information 2 Drilling Machines D-5 General Information 3 Operating Instructions 4-5 E-5 Parts 6 D-5 Parts 7! WARNING:

More information

Section 1, General information Introduction... 3 Description... 3 Specifications... 4 Wiring connections... 5

Section 1, General information Introduction... 3 Description... 3 Specifications... 4 Wiring connections... 5 LIST OF CONTENTS Section 1, General information Introduction... 3 Description... 3 Specifications... 4 Wiring connections... 5 Section 2, Calibration Calculations... 7 Calibration Procedure... 8 Section

More information

4.3 Section CONDUIT INSTALLATION ACCESSORIES. Thinking of the environment. Fixing accessories Coupling accessories

4.3 Section CONDUIT INSTALLATION ACCESSORIES. Thinking of the environment. Fixing accessories Coupling accessories CONDUIT INSTALLATION ACCESSORIES Thinking of the environment We use only fully recyclable halogen-free thermoplastics, without harmful additives. No cadmium or asbestos in the colourants either. For total

More information

B2...VS Series, 2-way, Ball Valve Bronze Body, Stainless Steel Ball and Stem

B2...VS Series, 2-way, Ball Valve Bronze Body, Stainless Steel Ball and Stem 2...VS Series, 2-way, all Valve ronze ody, Stainless Steel all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design Technical Data Media chilled or hot water, glycol, #

More information

Instruction Manual. HB Series Mini Level Sensor

Instruction Manual. HB Series Mini Level Sensor Instruction Manual Anderson Instrument Co., Inc. 156 Auriesville Road Fultonville, NY 12072 Phone: 8008330081 www.andersonnegele.com Instrument Model Number Instrument Serial Number HB Series Mini Level

More information

Receiver Controller and Transmitter

Receiver Controller and Transmitter 9-12 Receiver Controller and Transmitter Calibration Kit Instruction Booklet This kit is designed for use in: 1. The setup and calibration of receiver controllers. 2. Checking transmitter operation and

More information

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...

More information

Installation Instructions

Installation Instructions SYSTXBBSAM01 EVOLUTION SYSTEM ACCESS MODULE Installation Instructions NOTE: Read the entire instruction manual before starting the installation. pointsett U.S. Pat No. 7,415,102 Fig. 1 - Evolution System

More information

The transducer component converts the measured signal and displays the actual value.

The transducer component converts the measured signal and displays the actual value. Digital inductive conductivity transmitter System Integration Provides low Total Cost of Ownership PEEK/PPA version for CIP applications TEACH IN and SIMULATION Function Approval PVDF Version PEEK Version

More information

Knight Kit V44 VFO Stabilized by the Cumbria Design X-Lock 3.0

Knight Kit V44 VFO Stabilized by the Cumbria Design X-Lock 3.0 Knight Kit V44 VFO Stabilized by the Cumbria Design X-Lock 3.0 The Knight V44 VFO has a place in history. It was designed in the late 1950 s as a self contained VFO intended to plug into the crystal socket

More information

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard

Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard 5. Input Cover 6. O-Ring 7. Hex Head Cap Screw 8. Input

More information

FIELD CONTROL MODIFICATIONS MODEL YS CHILLERS (STYLE E)

FIELD CONTROL MODIFICATIONS MODEL YS CHILLERS (STYLE E) WIRING DIAGRAMS CONTRACTOR ORDER NO. JCI CONTRACT NO. JCI ORDER NO. Supersedes: 60.80-PW5 (999) Form: 60.80-PW5 (5) FIELD CONTROL MODIFICATIONS MODEL YS CHILLERS (STYLE E) PURCHASER JOB NAME LOCATION ENGINEER

More information

ph or ORP Transmitter

ph or ORP Transmitter ph or ORP Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma (Process + Temp) Removable backlighted display Universal process connection Compatible with 120 mm ph/ ORP probes

More information

Microprocessor Step Controller/Sequencer

Microprocessor Step Controller/Sequencer PRODUCT DATA 745/904 Series Microprocessor Step Controller/Sequencer The 745 and 904 Microprocessor Controllers are identical in every respect except for one feature. The 904 Series Sequencer includes

More information

Instructions AVC125-10: Voltage Regulator. Voltage Range. Maximum Continuous Burden. Voltage Range. Nominal Frequency

Instructions AVC125-10: Voltage Regulator. Voltage Range. Maximum Continuous Burden. Voltage Range. Nominal Frequency www.basler.com + 68.654.234 (USA) info@basler.com Model Description AVC25-0 Voltage Regulator INTRODUCTION The AVC63-2 and AVC25-0 regulate the level of excitation supplied to the field of a conventional,

More information

Electro Controls. Input-Output Modules WattsIndustries.co.uk

Electro Controls. Input-Output Modules WattsIndustries.co.uk Electro Controls Input-Output Modules - 2017 WattsIndustries.co.uk Input-Output Modules Section 08 B.M.S INPUT - OUTPUT MODULES SINGLE AND ADJUSTABLE RELAY ESRM.. Volt free contacts DIN RAIL mounted relay

More information

Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87

Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87 Instruction Manual 667 Actuator (Size 30/30i - 76/76i and 87) Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...

More information

SECTION 3 BASIC AUTOMATIC CONTROLS UNIT 12 BASIC ELECTRICITY AND MAGNETISM. Unit Objectives. Unit Objectives 2/29/2012

SECTION 3 BASIC AUTOMATIC CONTROLS UNIT 12 BASIC ELECTRICITY AND MAGNETISM. Unit Objectives. Unit Objectives 2/29/2012 SECTION 3 BASIC AUTOMATIC CONTROLS UNIT 12 BASIC ELECTRICITY AND MAGNETISM Unit Objectives Describe the structure of an atom. Identify atoms with a positive charge and atoms with a negative charge. Explain

More information

Table of Contents. Safety Notices

Table of Contents. Safety Notices IM0081 2018-01 Table of Contents Product Overview... 3 Principle of Operation... 3 Closed-Loop Servo Control with the FC-24 Controller... 4 Adjustments... 5 LED Status Indicators... 6 Installation...7

More information

Motor Accessories ACCESSORIES. GE TECMate Pro Service Tool. 760-ECM Motor Speed Controller. Broad Ocean ECM Motor Tester (Digimotor Test Tool)

Motor Accessories ACCESSORIES. GE TECMate Pro Service Tool. 760-ECM Motor Speed Controller. Broad Ocean ECM Motor Tester (Digimotor Test Tool) GENTEQ GENTEQ GE TECMate Pro Service Tool The Tecmate Pro Service Tool, stock #08500 is the latest advance in ECM technology developed by and for Genteq Motors. The Tecmate allows the service technician

More information

Ametek, Inc. Rotron Technical Products Division. 100 East Erie St., Suite 200 Kent, Ohio User's Guide. Number Revision F

Ametek, Inc. Rotron Technical Products Division. 100 East Erie St., Suite 200 Kent, Ohio User's Guide. Number Revision F Ametek, Inc. Rotron Technical Products Division 100 East Erie St., Suite 200 Kent, Ohio 44240 User's 120 Volt, 800 Watt and 240 Volt, 1200 Watt Brushless Motor Drive Electronics 5.7" (145 mm) and 7.2"

More information

KS TELETRAINER DESCRIPTION AND MAINTENANCE

KS TELETRAINER DESCRIPTION AND MAINTENANCE BELL SYSTEM PRACTICES AT&TCo Standard SECTION 473-411-100 Issue 4, January 1973 KS-16605 TELETRAINER DESCRIPTION AND MAINTENANCE 1. GENERAL 1.01 This section covers the description and maintenance of the

More information

Electronic fan speed regulators

Electronic fan speed regulators Electronic fan speed regulators Purpose The fan speed controller maintains the condensing pressure for fan-type condensers or fluid outlet temperatures for dry coolers, within prefixed values, for any

More information

DSSIU-6-1U. Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers.

DSSIU-6-1U. Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers. DSSIU-6-1U Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers. Powers up to 6 x DS50 to DS2000 at the same time. Supports calibration

More information

Installation Instructions

Installation Instructions CRLVHLGD017A00 CRLVHLGD026A00 - ACCESSORY LOUVERED HAIL GUARD GAS HEAT/ELECTRIC COOLING, ELECTRIC COOLING AND HEAT PUMP ROOFTOP UNITS 15 to 28 TONS Installation Instructions IMPORTANT: Read these instructions

More information

1525-BRS INFORMATION MANUAL SERV O D YN A M ICS. D y n ad r iv e Ave Crocker Suite 10 Valencia, CA

1525-BRS INFORMATION MANUAL SERV O D YN A M ICS. D y n ad r iv e Ave Crocker Suite 10 Valencia, CA 28231 Ave Crocker Suite 10 Valencia, CA 91355 818-700-8600 Servodynamics.com INFORMATION MANUAL 1525-BRS SERV O D YN A M ICS U SA www.servodynamics.com D y n ad r iv e Bru sh INDEX Page INTRODUCTION 2

More information

Over or Under Current. Over and Under Current Monitor. Current Transducer. Current Indicator. DIN Rail Mounting Current Monitors

Over or Under Current. Over and Under Current Monitor. Current Transducer. Current Indicator. DIN Rail Mounting Current Monitors Selection Guide...8.2 Over or Under ECS... 8.4 TCS... 8.8 Over and Under Monitor ECSW... 8.6 Transducer TCSA... 8.10 DCSA... 8.12 Indicator LCS... 8.14 LPM... 8.14 DIN Rail Mounting CM-SFS CM-SRS.1 CM-SRS.2

More information

D.C. BRUSHLESS MOTORS DRIVE. BLD07-IT Service Manual

D.C. BRUSHLESS MOTORS DRIVE. BLD07-IT Service Manual D.C. BRUSHLESS MOTORS DRIVE BLD07-IT Service Manual INTECNO s.r.l. Via Caduti di Sabbiuno n. 9/E 40011 Anzola Emilia (BO) - Italy tel. 051.19985350 fax 051.19985360 www.intecno-srl.com INDEX Description

More information

TURCK Inc Campus Drive Minneapolis, MN Application Support: PROX Fax: (763)

TURCK Inc Campus Drive Minneapolis, MN Application Support: PROX Fax: (763) A Sensor Designed with the Customer Applications in Mind! High Accuracy The PS400 and PS500 provide an accuracy rating of ±0.5 percent of the full scale. Flexible Mounting Options Multiple threaded connections

More information

MDC VAC Input Brushless Controller. User s Guide. 910 East Orangefair Lane, Anaheim, CA

MDC VAC Input Brushless Controller. User s Guide. 910 East Orangefair Lane, Anaheim, CA MDC200-048051 110VAC Input Brushless Controller User s Guide A N A H E I M A U T O M A T I O N 910 East Orangefair Lane, Anaheim, CA 92801 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471

More information

P o w e r. C O N T R O L S A N D a t h e n a c o n t r o l s. c o m. ATHENA CONTROLS, INC Campus Drive Plymouth Meeting, PA U.S.A.

P o w e r. C O N T R O L S A N D a t h e n a c o n t r o l s. c o m. ATHENA CONTROLS, INC Campus Drive Plymouth Meeting, PA U.S.A. P o w e r C O N T R O L S A N D a t h e n a c o n t r o l s. c o m ATHENA CONTROLS, INC. 5145 Campus Drive Plymouth Meeting, PA 19462-1129 U.S.A. TABLE OF CONTENTS Model Page Series 19/39 1 and Zero-Switched

More information

ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages

ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages ACCESSORY MODULE Including Protection, Performance, and Inlet Shut-off Valve Packages This manual must be used in conjunction with the Installation and Operation Manual for the water heater. - Do not store

More information

1-2 VOLTS PER HERTZ CHARACTERISTICS EXERCISE OBJECTIVE

1-2 VOLTS PER HERTZ CHARACTERISTICS EXERCISE OBJECTIVE 1-2 VOLTS PER HERTZ CHARACTERISTICS EXERCISE OBJECTIVE Set the rotation direction of the motor. Understand the V/f (volts per hertz) characteristics. Learn how to use an analog voltage to assign the frequency

More information

Materials (other materials see WIKA diaphragm seal program) Model S-10

Materials (other materials see WIKA diaphragm seal program) Model S-10 2.0 Specifications WIKA Tronic catalog pages and data sheets have a consistent layout of technical information that is required to select the correct transmitter. The second page of the data sheet lists

More information

Senior Swing. Caution

Senior Swing. Caution *740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product

More information

Installation & Operation Manual

Installation & Operation Manual The eco-friendly solution to hard water SB-1200, SB-2000, SB-2800, SB-3600 & SB-4000 Installation & Operation Manual 10/13 Industrial Electronic Descaler 120/240 VAC (Auto Selected) Table of Contents Section

More information

MODEL G0632Z 16" X 42" VARIABLE- SPEED WOOD LATHE MANUAL INSERT

MODEL G0632Z 16 X 42 VARIABLE- SPEED WOOD LATHE MANUAL INSERT MODEL G0632Z 16" X 42" VARIABLE- SPEED WOOD LATHE MANUAL INSERT The Model G0632Z is the same machine as the Model G0632 except it has a higher full-load current rating, a different inverter and inverter

More information

CONTENTS XV300K GB r doc XV300K 2/13

CONTENTS XV300K GB r doc XV300K 2/13 XV300K CONTENTS 1 PRELIMINARY CHECK GUARANTEE RECYCLING... 3 2 XV300K SPECIFICATIONS OF USE... 3 3 CODES - MODELS... 4 4 TECHNICAL SPECIFICATIONS... 4 5 STANDARD REFERENCES... 5 6 MECHANICAL INSTALLATION...

More information

30DC Speed Lathe Manual

30DC Speed Lathe Manual 30DC Speed Lathe Manual The Crozier Model 30DC Speed Lathe is our most popular model. It has many standard features not found on any other machine in its class or price range. Standard Features 3/4 HP

More information

BAPI-Stat 4 X-Combo, Room %RH and Temp. Sensor BA/BS4XC Installation & Operating Instructions

BAPI-Stat 4 X-Combo, Room %RH and Temp. Sensor BA/BS4XC Installation & Operating Instructions Overview and Identification The BAPI-Stat 4 X-Combo () Room Unit features 4 output channels and optional local indication of temperature and humidity. Additional options include Temperature Setpoint, Humidity

More information

Screw-in resistance thermometers with plug connector

Screw-in resistance thermometers with plug connector Data Sheet 90.2004 Page 1/7 s with plug connector for temperatures from -50 to +300 C highly resistant to shock and vibration connector locked in for reliable contact, IP65 or IP69K protection available

More information

658 Current to Position Converters

658 Current to Position Converters 658 Current to Position Converters Current to Position Converters for Solid State Switching Output Adjustable Zero, Span and Deadband Two Wire Input from Controller Operates with 90 to 1000 Ω Feedback

More information