Power shield that can drive: relays, solenoids, DC and stepper motors
|
|
- Berenice Jacobs
- 5 years ago
- Views:
Transcription
1 ILLUSTRATED KA0IP LUSTRA TED ASSEMBLY SE MANUAL AL HKA0IP Motor & Power shield Arduino Power shield that can drive: relays, solenoids, DC and stepper motors Features For use with Arduino Due, Arduino Uno, Arduino Mega Based on L98P dual full bridge driver IC Outputs: up to DC motors or bipolar stepper motor Power supply: external power or power from Arduino board Specifications Power supply: 7..VDC Max current: A Dimensions: 8 x mm /.7 x.08
2 Forum Participate our Velleman Projects Forum Subscribing our newsletter?, visit
3 Velleman N.V. Legen Heirweg 9890 Gavere (België)
4 assembly hints. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.. Make sure you have the right tools: A good quality soldering iron (-0W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any fl ux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fl y towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fi ne. For some projects, a basic multi-meter is required, or might be handy. Assembly Hints : Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes, the values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.. Soldering Hints :. Mount the component against the PCB surface and carefully solder the leads Make sure the solder joints are cone-shaped and shiny. Trim excess leads as close as possible to the solder joint - -
5 DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST! - -
6 Construction I Resistors R... R: K7 ( B) R: 0K ( B) R: K7 ( B) R: K7 ( B) R: 0K ( B) R: K7 ( B) R7: K ( B) R8: K ( B) R9: 00K ( B) R0: 0K ( B) CONSTRUCTION Ceramic capacitors c... C: 00nF (0) Shottky diode D: N89 D: N89 D: N89 D: N89 D: N89 D: N89 D7: N89 D8: N89 Transistors Male header T: BC7B T: BC7B x p x 8p 7 Female header Do not cut the connector pins! LED s Watch the polarity! c... SK8... SK0 : xpin C (-) LD LD - -
7 Construction 8 Terminal blocks 0 Dual Full Bridge driver Watch the position of the notch! IC: L98P SK : p (motor ) SK : p (motor ) SK : p (power supply) Solder 9 Electrolytic capacitors C... Watch the polarity! C: μf C: 00μF Solder each connection - 7 -
8 Connection diagram II CONNECTION DIAGRAM MOTOR DIRECTION LD Motor LD Motor PIN SELECT A MOTOR S DC Motor B BIPOLAR STEPPER MOTOR DC Motor DC MOTOR EXTERNAL POWER SUPPLY INPUT Max. 0VDC/A SELECT POWER SOURCE Vin: Power from Arduino (max. A) PWR: Power from external supply (max. 0VDC/A) DOWNLOAD SAMPLE CODE FROM KA0 PAGE ON
9 - 9 - SENSE A NC OUT OUT VS INPUT 7 ENABLE A 8 INPUT SENSE B 9 NC 8 OUT 7 OUT INPUT ENABLE B INPUT VSS HEAT L98 IC LEDRL LD LEDRL LD SCREW0 SK SK Vin V V RST SK A0 A A A A A 7 8 SK ARDUINO UNO 7 8 SK AREF - - K R7 K R8 N89 D N89 D N89 D N89 D N89 D N89 D N89 D7 N89 D8 SK7 Vin SCREW0 SK POWER POWER POWER POWER XPIN HEADER PITCH.MM SK8 ENA ENA XPIN HEADER PITCH.MM SK9 ENB ENB 9 0 XPIN HEADER PITCH.MM SK0 XPIN HEADER PITCH.MM SK DIRA DIRB 7 8 DIRA DIRB BC7 T DIRA K7 R 0K R K7 R V V DIRA DIRA BC7 T DIRB K7 R 0K R K7 R V DIRB DIRB SCREW0 SK POWER 00n C 00μ/-00V C 00K R9 0K R0 A μ C Schematic diagram
10 PCB - 0 -
11 Leds and how to use them Leds feature a specific voltage drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current! Never connect leds in parallel How to Calculate the series resistor: Example: operate a red led (.7V) on a 9Vdc source. Required led current for full brightness: ma (this can be found in the datasheet of the led) Supply voltage (V) - led voltage (V) = series resistance (ohms) required current (A) 9V -.7V = 0 ohm 0.00A Required resistor power handling= voltage over resistor x current passed trough resistor (9V -.7V) x 0.00A = 0.0W closest value : use a k resistor a standard /W resistor will do the job open collector outputs An open collector output can be compared to a switch which switches to ground when operated LEDs in series: Example: x red led (.7V) on 9V battery Required led current for full brightness: ma (this can be found in the datasheet of the led) Example: How to switch an LED by means of an open collector output Supply voltage (V) - (number of leds x led voltage (V)) = series resistance (ohms) required current (A) 9V - ( x.7v) = 780 ohm 0.00A use an 80 ohm resistor
12 The new Velleman Projects catalogue is now available. Download your copy here: Modifi cations and typographical errors reserved - Velleman nv. HKA0 IP Velleman NV, Legen Heirweg Gavere.
Configure your Arduino as a simple web server or let it get data from the worldwide web.
KA0 ILLUSTRATED LUSTRA TED ASSEMBLY SE MANUAL HKA0IP KA0 Ethernet shield for Arduino Configure your Arduino as a simple web server or let it get data from the worldwide web. Features For use with Arduino
More informationTotal solder points: 198 Difficulty level: beginner advanced DUAL ELECTRONIC DICE K3400 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 198 Difficulty level: beginner 1 2 3 4 5 advanced DUAL ELECTRONIC DICE K3400 Cheating is no longer possible! ILLUSTRATED ASSEMBLY MANUAL H3400IP-1 Features & Specifications Features:
More informationTotal solder points: 82 Difficulty level: beginner advanced. Dc to Pulse Width Modulator K8004 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 82 Difficulty level: beginner 1 2 3 4 5 advanced Dc to Pulse Width Modulator K8004 Allows very efficient control of DC motors, heaters or lights. ILLUSTRATED ASSEMBLY MANUAL H8004IP-2
More informationTotal solder points: 247 Difficulty level: beginner advanced. 10 Channel, 2-Wire REMOTE CONTROL K8023 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 247 Difficulty level: beginner 1 2 3 4 5 advanced 10 Channel, 2-Wire REMOTE CONTROL K8023 Control up to 10 devices from a distance using only 2 wires. ILLUSTRATED ASSEMBLY MANUAL H8023IP-1
More informationTotal solder points: 33 Difficulty level: beginner advanced. 7W mono amplifier K4001 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 33 Difficulty level: beginner 1 2 3 4 5 advanced 7W mono amplifier K4001 Small but powerful multipurpose amplifier. ILLUSTRATED ASSEMBLY MANUAL H4001IP-1 2 Features & Specifications
More informationK8066 3W MONO AMPLIFIER. Specifications
Total solder points: 34 Difficulty level: beginner 1 2 3 4 5 advanced 3W MONO AMPLIFIER K8066 Small but powerful amplifier suits a wide range of applications. Specifications Output power : 3Wrms (4-8 ohm,
More informationTotal solder points: 42 Difficulty level: beginner advanced UNIVERSAL STEREO PRE - AMPLIFIER K2572 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 42 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL STEREO PRE - AMPLIFIER K2572 Low noise preamplifier to boost small signals. ILLUSTRATED ASSEMBLY MANUAL H2572IP-1 Features
More informationTotal solder points: Difficulty level: beginner advanced 0 TO 60 HOUR START / STOP TIMER K6200 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 96 + 43 Difficulty level: beginner 1 2 3 4 5 advanced 0 TO 60 HOUR START / STOP TIMER K6200 Broad range mains operated start / stop timer. ILLUSTRATED ASSEMBLY MANUAL H6200IP-1 VELLEMAN
More informationTotal solder points: Difficulty level: beginner advanced 3 DIGIT PANEL METER KIT K2032 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 65 + 49 Difficulty level: beginner 1 2 3 4 5 advanced 3 DIGIT PANEL METER KIT K2032 Ideal replacement for moving coil meters ILLUSTRATED ASSEMBLY MANUAL H2032IP-1 Features & Specifications
More informationVOLUME AND TONE CONTROL - PREAMPLIFIER K8084
VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control H8084IP-1 Features & specifications When
More information400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
More informationTotal solder points: 163 Difficulty level: beginner advanced SPEAKER PROTECTION KIT K4700 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 163 Difficulty level: beginner 1 2 3 4 5 advanced SPEAKER PROTECTION KIT K4700 Protects your precious speakers against switch-on clicks and DC current. ILLUSTRATED ASSEMBLY MANUAL
More informationTotal solder points: 79 Difficulty level: beginner advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 79 Difficulty level: beginner 1 2 3 4 5 advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. ILLUSTRATED ASSEMBLY MANUAL H4102IP-1
More informationTotal solder points: 47 Difficulty level: beginner advanced METAL DETECTOR K7102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 47 Difficulty level: beginner 1 2 3 4 5 advanced METAL DETECTOR K7102 Avoid disasters when drilling holes in walls... ILLUSTRATED ASSEMBLY MANUAL H7102IP Features & Specifications
More informationTotal solder points: 108 Difficulty level: beginner advanced PINK NOISE GENERATOR K4301 ILLUSTRATED ASSEMBLY MANUAL H4301IP-1
Total solder points: 108 Difficulty level: beginner 1 2 3 4 5 advanced PINK NOISE GENERATOR K4301 Add a spectrum analyser with a microphone and check your audio system performance. ILLUSTRATED ASSEMBLY
More informationK2601 STROBOSCOPE. Features
Total solder points: 38 Difficulty level: beginner 1 2 3 4 5 advanced STROBOSCOPE K2601 Great for party s, stage, photography,... Features Power supply : 220-240VAC Power consumption : 3-10W Flash frequency
More informationTotal solder points: 63 Difficulty level: beginner advanced 2 CHANNEL RF CODELOCK TRANSMITTER K8059 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 63 Difficulty level: beginner 1 2 3 4 5 advanced 2 CHANNEL RF CODELOCK TRANSMITTER K8059 For use with K8057/VM109 2 Channel RF receiver ILLUSTRATED ASSEMBLY MANUAL H8059IP-1 VELLEMAN
More informationTotal solder points: 101 Difficulty level: beginner advanced ELECTRONIC WATCHDOG K2655 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 101 Difficulty level: beginner 1 2 3 4 5 advanced ELECTRONIC WATCHDOG K2655 Listens and scares intruders with realistic barking. ILLUSTRATED ASSEMBLY MANUAL H2655IP-2 Features & Specifications
More informationTotal solder points: 77 Difficulty level: beginner advanced OPTICAL PROXIMITY SWITCH K8092 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 77 Difficulty level: beginner 1 2 3 4 5 advanced OPTICAL PROXIMITY SWITCH K8092 Operate by waving hand or object in front of unit ILLUSTRATED ASSEMBLY MANUAL H8092IP-1 Features & Specifications
More informationTotal solder points: 338 Difficulty level: beginner advanced. Remote control by telephone K6501 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 338 Difficulty level: beginner 1 2 3 4 5 advanced Remote control by telephone K6501 Operate your appliances from anywhere with a simple phone call. ILLUSTRATED ASSEMBLY MANUAL H6501IP-1
More informationTotal solder points: 271 Difficulty level: beginner advanced. 2 x 15 LED STEREO VU METER K4306 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 271 Difficulty level: beginner 1 2 3 4 5 advanced 2 x 15 LED STEREO VU METER K4306 For high precision audio level indication ILLUSTRATED ASSEMBLY MANUAL H4306IP-1 Features & Specifications
More informationTotal solder points: 66 Difficulty level: beginner advanced. 15 Channel IR remote stick K8051 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 66 Difficulty level: beginner 1 2 3 4 5 advanced 15 Channel IR remote stick K8051 Sleek designer enclosure with just 2 buttons, yet it provides acces to a stunning 15 channels. ILLUSTRATED
More informationK8039 DMX CONTROLLED POWER DIMMER. Control a lamp or group of lamps trough a DMX signal. Suitable for resistive and mains voltage halogen lighting.
DMX CONTROLLED POWER DIMMER K8039 Control a lamp or group of lamps trough a DMX signal. Suitable for resistive and mains voltage halogen lighting. Specifications control source: DMX-512, 3 pin XLR socket
More informationTotal solder points: 47 Difficulty level: beginner advanced METAL DETECTOR K7102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 47 Difficulty level: beginner 1 2 3 4 5 advanced METAL DETECTOR K7102 Avoid disasters when drilling holes in walls... ILLUSTRATED ASSEMBLY MANUAL H7102IP Features & Specifications
More informationEight channel remote relay card. Total solder points: 277 Difficulty level: beginner advanced K8056 ILLUSTRATED ASSEMBLY MANUAL
Eight channel remote relay card This relay card can be used in several ways : stand alone card, addressed by switches or open collector outputs or remote controlled through RS232. Total solder points:
More informationK8055N. USB Experiment interface board. Interface your computer with the world using 5 digital in and 8 outputs, 2 analogue in-and outputs.
Total solder points: 313 Difficulty level: beginner 1 2 3 4 5 advanced USB Experiment interface board K8055N Interface your computer with the world using 5 digital in and 8 outputs, 2 analogue in-and outputs.
More informationTotal solder points: 91 Difficulty level: beginner advanced 2 CHANNEL RF RECEIVER K8057 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 91 Difficulty level: beginner 1 2 3 4 5 advanced 2 CHANNEL RF RECEIVER K8057 For use with K8059/VM108 2 Channel RF transmitter ILLUSTRATED ASSEMBLY MANUAL H8057IP-1 Assembly hints
More information10W Class D Stereo Amplifier Kit
1 Total Solder Joints: 70 Difficulty Level : beginner expert 10W Class D Stereo Amplifier Kit PARADIGM Technologies (UK) Ltd Electronic Kits and Modules K1420 High power multipurpose audio amplifier Specifications
More information10W Class D Ultra Stereo Amplifier Kit
1 Total Solder Joints: 70 Difficulty Level : beginner expert PARADIGM Technologies (UK) Ltd Electronic Kits and Modules 10W Class D Ultra Stereo Amplifier Kit K1421 High power / quality audio amplifier
More information1A POWER SUPPLY K1823
Total solder points: 27 Skill level : 1 1A POWER SUPPLY K1823 Applications : Just add a suitable transformer (see table inside) Great to power your projects and save on batteries Use as adjustable power
More informationBill of Materials: PWM Stepper Motor Driver PART NO
PWM Stepper Motor Driver PART NO. 2183816 Control a stepper motor using this circuit and a servo PWM signal from an R/C controller, arduino, or microcontroller. Onboard circuitry limits winding current,
More informationπλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets
πλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets Specifications Power supply: +5V DC/50mA Dimensions: 100 x 100 x 23mm Congratulations on purchasing
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationK2655. Electronic watchdog. Features: Specifications :
Total solder points: 101 Difficulty level: beginner 1 2 3 4 5 advanced Features: Electronic watchdog K2655 Very realistic simulation through the use of a random generator. Choice of two different dogs.
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationLITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
More informationLine-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
More informationTwo channel codelock receiver
Total solder points: 224 Difficulty level: beginner 1 2 3 4 5 advanced Two channel codelock receiver K6727 Features: Easy to build: no coils to be made! Works together with the K6706/K6706A two channel
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: May 1,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thanks for constructing the TKEY-1A CW touch key Have
More information3. Assembly manual ANALYZING THE PCB'S LCD PCB. Component side: Solder side:
3. Assembly manual ANALYZING THE PCB'S LCD PCB Component side: Solder side: MAIN PCB Component side: Solder side: ASSEMBLGING THE LCD PCB 1. Resistor R1: 33 Ohm (orange, black, black) 2. 6 Pin female header
More informationIR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015
IR add-on module circuit board assembly - Jeffrey La Favre January 27, 2015 1 2 For the main circuits of the line following robot you soldered electronic components on a printed circuit board (PCB). The
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationPacific Antenna Easy SWR Indicator Kit
Pacific Antenna Easy SWR Indicator Kit Description Monitoring the match of an antenna to your transmitter or adjusting an antenna tuner for best match requires an indicator of the reflected power as an
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
More informationOcean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller
Ocean Controls KT-5198 Dual Bidirectional DC Motor Speed Controller Microcontroller Based Controls 2 DC Motors 0-5V Analog, 1-2mS pulse or Serial Inputs for Motor Speed 10KHz, 1.25KHz or 156Hz selectable
More informationMICROGRANNY v2.1 - Assembly Guide
last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl
More informationLine Following Circuit Board Wiring Guide
Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationPacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationIntroduction 1. Download socket (the cable plugs in here so that the GENIE microcontroller can talk to the computer)
Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away
More informationTekBot Remote Control Receiver Board Construction
TekBot Remote Control Receiver Board Construction Purpose This tutorial illustrates the procedure for construction of the Receiver board for the TekBot. A Guide to Soldering Many of you have soldered once
More informationINSTANT ROBOT SHIELD (AXE408)
INSTANT ROBOT SHIELD (AXE408) 1.0 Introduction Thank you for purchasing this Instant Robot shield. This datasheet is designed to give a brief introduction to how the shield is assembled, used and configured.
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationDC Motor. Controller. User Guide V0210
DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,
More informationPacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
More informationBill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
More informationRead This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions contact qrpkits.com@gmail.com There is no need to print out the whole assembly
More informationVC Divider Assembly manual
1 VC Divider Assembly manual Thank you for your purchase of the SSSR Labs VC Divider DIY Kit! This manual will help you assemble the VC Divider quickly and easily. Follow the instructions! As you may know,
More informationElectronic Components
Electronic Components Arduino Uno Arduino Uno is a microcontroller (a simple computer), it has no way to interact. Building circuits and interface is necessary. Battery Snap Battery Snap is used to connect
More informationTemperature activated switch
Build instructions, circuit explanation and example applications Issue 1.5 Product information: www.kitronik.co.uk/quicklinks/2113/ TEACHER Temperature activated switch Introduction About the project kit
More informationDuoDrive Nixie Bargraph Kit
Assembly Instructions And User Guide Nixie Bargraph Kit - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 12 December 2017 New document - 2 - 1. INTRODUCTION 1.1 About Nixie Bargraph Driver IN-9
More informationInstructions for Building the Pulsed Width Modulation Circuit. MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08)
Instructions for Building the Pulsed Width Modulation Circuit MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08) Congratulations on your purchase of the MC-12 DC Motor
More informationHEAT ACTIVATED SWITCH KIT
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE REACT TO THE TEMPERATURE WITH THIS HEAT ACTIVATED SWITCH KIT Version 2.1 Heat Activated Switch Teaching
More informationModifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
More informationElektor Construction Guide TAPIR
Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1
More informationWarm Tube Clock. Before we start, please make sure that you have all required parts that come for the main board :
Warm Tube Clock Assembly Instructions for the main board Introduction Congratulations on your purchase of OSH Nixie Tube Clock. In this document you will see all steps you need to follow in order to successfully
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationRead This Page First
Pacific Antenna 0 Watt HF Amplifier Kit Manual This is Version 5.5 dated 060505 Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions
More informationBill of Materials: General Purpose Alarm, Pulsed PART NO
General Purpose Alarm, Pulsed PART NO. 2190207 I hate alarms that sound continuously - unless they are smoke alarms. Smoke alarms should be annoying, but others should not. I wanted an alarm for a function
More information16 Bit Micro Experimenter Assembly and Check out Instructions
16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly
More informationGuitarpedalkits.com Overdrive Pedal Build Instructions
Page 1 Guitarpedalkits.com Overdrive Pedal Build Instructions Follow the instructions in this guide to build your very own DIY overdrive pedal from GuitarPedalKits.com. If you re a first time builder,
More informationTHE RING RESONATOR (K-975)
THE RING RESONATOR (K-975) OUTPUT BOOST The Ring Resonator An Octave Up Fuzz Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery life. Use these instructions
More information5W Mono Amplifier Kit
5W Mono Amplifier Kit Kit Construction Before you start assembling your kit there are a couple of important things you must do. FIRST read through these instructions entirely before you start construction
More informationCompact Motor Driver Robot Shield
Compact Motor Driver Robot Shield Build Time: 25 mins Skill Level: Beginner (2/5) Here s your task - putting Arduino brains into the soulless shell of your mechanical monster. Ah, but what are brains without
More informationKASTLE v1.5 - Assembly Guide
last update: 14. 12. 2017 KASTLE v1.5 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the Kastle kit - mini modular synthesizer. It is suitable for beginners. It is
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationLA502 Assembly guide Main PCB Resistors - (2)
LA502 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationAssembly and User Guide
Assembly and User Guide AtariPunkr is an adjustable stepped tone generator. AtariPunkr provides hours of fun everyone! Powered by: 9V Battery Outputs: Mylar Speaker (Included) Stereo Output (3.5mm Jack)
More informationLED Infinity Mirror Controller, 32 LEDs, Multiple Patterns.
http://wwwinstructablescom/id/led-infinity-mirror-controller-32-leds-multiple-/ Food Living Outside Play Technology Workshop LED Infinity Mirror Controller, 32 LEDs, Multiple Patterns by ChromationSystems
More informationSoldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT.
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT. Soldering 101 Soldering is the process of joining two metals together to form an electrically ll and mechanically secure bond using heat and a third
More informationCongratulations on your purchase of the SparkFun Arduino ProtoShield Kit!
Congratulations on your purchase of the SparkFun Arduino ProtoShield Kit! Well, now what? The focus of this guide is to aid you in turning that box of parts in front of you into a fully functional prototyping
More informationThe ability to make basic voltage and resistance measurements using a digital multimeter
Congratulations on your purchase of a new OneShot chassis! The PC01 OneShot combines a rugged enclosure, power supply, and discrete instrument DI in a compact 1/4U package. A few minutes of assembly are
More informationGat ew ay T o S pace AS EN / AS TR Class # 07. Colorado S pace Grant Consortium
Gat ew ay T o S pace AS EN / AS TR 2500 Class # 07 Colorado S pace Grant Consortium One Minute Reports: - Can we have two data loggers? - Do you provide us with cameras? {Hardware Checkout after proposal}
More informationModification of USB Sound Card for Asterisk app_rpt Use
Modification of USB Sound Card for Asterisk app_rpt Use First off a huge thank you to Steve for providing the original notes on how to modify a USB sound card. (http://images.qrvc.com/usbfob.pdf) These
More informationPacific Antenna Code Practice Oscillator Kit
Pacific Antenna Code Practice Oscillator Kit This kit is offered to initiate the first time builder in the various techniques of mechanical and electronic kit construction. At the end of the approximately
More informationTS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationBP-1A. Band-Pass variable filter continuous tuning from 3 to 30MHz. For analogue or software-defined receivers (SDR) Assembly manual
BP-1A Band-Pass variable filter continuous tuning from 3 to 30MHz. For analogue or software-defined receivers (SDR) Assembly manual Last updated: December 1, 2017 ea3gcy@gmail.com Updates and news at:
More informationUltrasound Range Finder
Ultrasound Range Finder PCB Version 1.0 Assembly Manual Range Finder Assembly Instructions Read This Before You Begin 1. Avoid touching the PCB copper traces and pads with your fingers until you are ready
More informationInstructions for Building the Pulsed Width Modulation Circuit. MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 8/08)
Instructions for Building the Pulsed Width Modulation Circuit MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 8/08) Using this circuit for a pulsed DC current to your cell. Do
More informationTHE THUNDERDRIVE (K-950)
THE THUNDERDRIVE (K-950) OUTPUT DISTORTION Unplug when not in use to save battery life. TO AMP IN The Thunderdrive Modkitsdiy.com FROM GUITAR OUT Use these instructions to learn: How to build an effects
More informationEASY BUILD TIMER KIT TEACHING RESOURCES. Version 2.0 LEARN ABOUT SIMPLE TIMING CIRCUITS WITH THIS
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE LEARN ABOUT SIMPLE TIMING CIRCUITS WITH THIS EASY BUILD TIMER KIT Version 2.0 Index of Sheets TEACHING
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationConstruction notes for the symmetrical 400 watt amplifier
Construction notes for the symmetrical 400 watt amplifier Introduction The symmetrical amplifier is an update of one of my designs, which appeared in the Australian electronics magazine Silicon Chip in
More informationAxis Fuzz Kit Building Manual
Axis Fuzz Kit Building Manual Effect Pedal Kits: Axis Fuzz The Axis Fuzz Kit is based in the Roger Mayer Axis Fuzz, the effect pedal responsible for Jimi Hendrix sound in Axis Bold As Love. What else is
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More information