SE3401. Installation Instructions Wireless (RF) Point Tracking Transmitter

Transcription

1 SE340 EN Installation Instructions Wireless (RF) Point Tracking Transmitter

2 SE340 Installation Instructions.0 General Information EN.0 General Information The SE340 Point Transmitter is a magnetic and dry contact wireless transmitter used for monitoring assets. The unit is equipped with an internal reed contact for use with an external magnet assembly (included), a cover tamper switch, and RF supervision. The SE340 can accept a supervised dry contact input from an external device.. Supervision Supervision is provided by transmitting a low power level signal to the receiver every 70 min. if there is no other activity. All transmissions from the SE340 send battery status information to the system.. Auto Tracking Once an alarm is initiated, such as the transmitter moved away from the magnet, the auto tracking feature begins. The transmitter sends a signal back to the central console every few seconds, updating its location for several minutes. To reset the transmitter after an alarm has been initiated, all device conditions (such as tamper, loop, or magnet) must be reset to normal..0 Specifications Table : Specifications 3.0 Mounting the Point Transmitter Avoid mounting the point transmitter on metal surfaces as it can reduce the range of the unit. Placing the point transmitter on ferrous metal (iron or steel) surfaces can affect operation of the magnetic contact. 3. Recommended Mounting. Position the mounting plate over the desired location and attach it with the supplied screws. Figure : Attach Mounting Plate - Release tab - Mounting holes M A G N E T. Depending on the product you are using, select the picture that best describes it to open the cover. Description SE340 Wireless Point Tracking Transmitter Figure : Open Cover Dimensions (H x W x D) Transmitter without Mounting Plate: 35 mm x 76.5 mm x 9 mm (.4 in. x 3.5 in. x 0.75 in.) Mounting Plate: 35 mm x 76.5 mm x 3. mm (.4 in. x 3.5 in. x 0.5 in.) Operating Temperature Operating Voltage -0 C to +65 C (-4 F to +50 F) Supplied by a 3 VDC lithium battery. Battery Life Up to five years under normal usage with the recommended battery types. Higher usage decreases battery life. Recommended Battery Types Duracell DL 3A, Energizer EL 3AP, or Panasonic CR 3A Compatible Receivers EA0A-304 Options Magnet-RF-0 Assembly (supplied in packages of ten) - Insert screwdriver and press here - Push in Bosch Security Systems 6/03 408E

3 SE340 Installation Instructions 3.0 Mounting the Point Transmitter EN 3 3. Be sure to note the location of the magnet when mounting the base. 4. Slide the point transmitter over the base to lock it into place as shown is Figure 3. Figure 3: Slide Point Transmitter Over Base 3. Mounting Without the Mounting Plate. If the battery was installed in the point transmitter, remove it at this time.. Using a small screwdriver, gently lift the printed circuit board away from the case mounting clips. You do not need to remove the cover to remove the board. Figure 5: Lift Printed Circuit Board 5. The point transmitter can be released from the base by pressing the release tab with a small screwdriver or a paper clip. 6. For higher security installations, mount the transmitter using the tamper screw provided (see Figure 4). Figure 4: Mount Transmitter Using Tamper Screw 3. Rock the board gently to loosen the battery clips from the case and slide the board away from the mounting clips near the area where the cover connects to the base. 4. Mount the point transmitter in the desired location, taking note the magnet needs to be on the same side of the case as the reed switch. Figure 6: Mount Point Transmitter in Desired Location - Tamper screw - Magnet side - Mounting holes Bosch Security Systems 6/03 408E

4 SE340 Installation Instructions 4.0 Installing the Battery EN Mounting the Magnet Mount the magnet as shown in Figure 7. The magnet must mount within 9 mm (0.75 in.) of the base of the unit. Figure 7: Mount the Magnet 4.0 Installing the Battery Install the recommended type of battery: Duracell DL3A, Energizer EL3AP, or Panasonic CR3A. Be sure to observe the polarity. Figure 8: Install Battery - End view from the opening end - Battery Bosch Security Systems 6/03 408E

5 SE340 Installation Instructions 5.0 Setting Up Magnetic or External Contacts EN Setting Up Magnetic or External Contacts The SE340 has the capacity to monitor magnetic and/or dry external contacts. External Normally Closed (NC) or external Normally Open (NO) contacts can be monitored. Figure : Magnet (Optional) Typical NO Wiring Figure 9: Magnet - Battery - EOL. kω - Battery - EOL Note: If not using external contacts, you must install the EOL. Figure 0: Magnet (Optional) Typical NC Wiring - Battery - EOL. kω Bosch Security Systems 6/03 408E

6 SE340 Installation Instructions 6.0 System Programming EN System Programming A two part ID sticker is located on the enclosure. You need the number on this sticker to program this device into the system. See your Security Escort Reference Guide for programming information for wireless type devices. Figure : ID Sticker FCC Compliance Notice This device complies with Part 5 of the FCC rules and with RSS-0 of Industry and Science Canada. Operation is subject to the following two conditions: This device cannot cause harmful interference. This device must accept any interference received, including interference that can cause undesirable operation. Changes or modifications not expressly approved by Bosch Security Systems can void the user s authority to operate the equipment ID number Bosch Security Systems 6/03 408E

7 SE340 Installation Instructions Notes: EN 7 Notes: Bosch Security Systems 6/03 408E

8 Bosch Security Systems 30 Perinton Parkway Fairport, NY USA Customer Service: (800) Technical Support: (888) Bosch Security Systems Subject to change Printed in the USA 408E