Starbox. Installation guide

Transcription

1 Starbox Installation guide

2 Introduction Welcome The Starbox is a wiring centre that allows ican networks to be wired in a star topology (as an alternative to the standard daisy-chain topology). The Starbox is a passive device, which does not process ican messages nor does it appear in any of the ilight software tools used for network configuration or monitoring. The Starbox connects to seven ican networks. Messages input from an ican network, is sent to the other six ican networks. There is one Master and six Secondary ican networks. The only difference between them is that the Master must be connected as it provides power to the Starbox microprocessor. Specification General A. The unit requires 240 VAC 50/60Hz, 1A single phase supply B. Ambient temperature range 0 C to 40 C (32 F to 104 F) C. Humidity 5% to 95% Non-condensing D. Reprogrammable FLASH memory E. Seven ican networks F. Internal +12 VDC, 2A power supply G. Alarm input Dimensions Weight Packed: Unpacked: 2.6 kg (5.7 lbs.) 2.4 kg (5.3 lbs.) Product Overview Six Secondary network connectors each with a green (power) and yellow (network activity) LED 2. Starbox reset button 3. Reprogramming Connector 4. Master network connectors (2) with a green (power) and yellow (network activity) LED 5. Mains Supply Terminal Block 6. Alarm input with red status LED 7. Internal Power Supply P1

3 Safety! WARNING HAZARDOUS VOLTAGES DISCONNECT FROM SUPPLY BEFORE REMOVING COVERS NO USER SERVICEABLE PARTS INSIDE SERVICE BY QUALIFIED PERSONNEL ONLY Please read this first By following the steps listed below and elsewhere within this guide, you can ensure safe installation and operation of this unit. The installation must comply with the appropriate electrical codes and regulations in force in your area. Ensure that all wiring used conforms fully to local specifications and is sufficiently rated for the installation. All new wiring must be fully verified before applying power. Ensure that high voltage and low voltage wiring remains separate. Mounting Location and spacing The Starbox should be installed in a dry ventilated location, where ambient conditions are maintained within the requirements of the unit. The unit has ventilation slots on the sides to allow convection cooling and under no circumstances should these be blocked. Allow 50mm (2 ) above and below the unit if trunking with a depth greater than 50mm (2 ) is used. Ambient atmosphere requirements Temperature: 0 C to +40 C (32 F to 104 F) Humidity: 5% to 95% Non-condensing Mounting Holes The unit is provided with four 6.35mm (0.25 ) diameter fixing holes for wall mounting. The mounting holes can be accessed by undoing the four screws on the front cover and removing it. 6.35mm (0.25") Mounting Holes 4-Off. 180mm (7.09in) 175mm (6.89in) P2

4 Supply Wiring Connecting the Supply This unit requires a V (50-60 Hz) single phase supply (live and neutral) with 1.0 A capability. A screwless terminal block is used to connect the mains input to the internal power supply There is no electrical isolation between ican networks. The shield on each connector is connected to chassis ground via a 470K ohm resistor. Master ican Network The Master network must be used because the Starbox is powered by the 12V of the Master network. The green LED (LD1) indicates that the Master network and the Starbox is powered. As shipped from the factory, the Master network is powered by the internal power supply. Two 5 way connector blocks (CON1 and CON2) are provided for the connection of the ican network cable to the Master terminals. The Master ican network is also connected to an RJ12 (CON9) socket in parallel with CON1 and CON2. The yellow LED (ACT) next to the master network connectors indicates Master ican network activity. Wire Gauge for Supply Terminals The live, neutral, and earth mains input are pushed into the terminals on the input side of the connector. Each of these wires can only be released by depressing the corresponding tab. Mains input cable size for live, neutral, and earth is from 1.00mm 2 to 2.5mm 2. Neutral Earth Live Control Wiring ican Network All ican Messages received by the Starbox from any network are output to the other six ican networks. Secondary ican Network One 5 way connector is provided for each of the six Secondary ican Networks (1-6, CON3-8 respectively). When power (+12V and 0V) is connected to each of the Secondary ican networks the green LED (PWR) is turned ON. The yellow LED (ACT) indicates network activity on that Secondary ican network. Each of the secondary green power LEDs must be connected to +12V and 0V. This can be achieved by the following options: Connect them to the master connector via wire jumpers Connect them to an external power supply. Connect them to an external icanet device. P3

5 ican Network Wiring The following cable strategies may be used for wiring the ican network. It is not recommended to mix cable types in a single installation. Use Belden cable to maximise network runs up to 1000m without a bridge/repeater. Cable type: Belden 1502R or 1502P Maximum cable length: 1000m (3275 ft.) Devices per segment: 100 (without bridge or repeater) Use CAT5 FTP for economy and wide availability, but there are tighter limitations on the network run without a bridge/repeater. Cable type: Maximum cable length: Devices per segment: Network Termination CAT 5 FTP 305m (1000 ft.) 100 (without bridge or repeater) ican devices are daisy-chained on the network. Spurs from the network are not permitted and will result in communication problems. Devices on an ican network can be wired in any order. Termination is required at both ends of the network. Alarm Input Connector CON11 (AL and 0V) provide an Alarm input to the Starbox. The Starbox outputs an Alarm On message to all connected ican networks when AL is shorted to OV. The Starbox outputs an Alarm Off message to all connected ican networks when the short between AL and 0V is cleared. Operation Commissioning The Starbox must be energized from the mains for it to operate. The Master green LED indicates that the unit is powered correctly. A red flashing LED indicates that the unit is operating normally. When the red LED is ON, it indicates that there Alarm inputs are close together. Intermittent flashing yellow LEDs indicate that ican messages have been output on the corresponding network. The icanet cables carry low voltage signals and misconnection of these cables could result in damage to the Starbox and devices connected on the network. Verify ican Networks The Starbox is provided with a termination resistor fitted to each ican network. For each ican network that terminates in the Starbox, keep the 120 ohm resistor connected across CAN-H and CAN-L. For each ican network that does not terminate in the Starbox, remove the 120 ohm resistor from that connector and store it in the bottom of the Starbox for future use. Connect an icanet control panel, whose buttons have been programmed with ican messages, to the master network and terminate appropriately. Connect a PC node to secondary 1 network and run icansoft monitor. Press a control panel button and check that the message sent by the control panel is received by icansoft monitor. If the message is not received, check the cabling and termination resistors. Repeat the above process for all secondary networks. P4

6 ilight Cooper Controls Limited Unit 4, Enterprise Centre Penshurst, Tonbridge Kent, TN11 8BG Tel: +44 (0) Fax: +44 (0) All products manufactured by Cooper Controls and identified with the ilight brand are warranted to be free from defects in material and workmanship and shall conform to and perform in accordance with Seller s written specifications. For detailed warranty information, visit our website at This warranty will be limited to the repair or replacement, at Seller s discretion, of any such goods found to be defective, upon their authorized return to Seller. This limited warranty does not apply if the goods have been damaged by accident, abuse, misuse, modification or misapplication, by damage during shipment or by improper service. There are no warranties, which extend beyond the hereinabove-limited warranty, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS. No employee, agent, dealer, or other person is authorized to give any warranties on behalf of the Seller or to assume for the Seller any other liability in connection with any of its goods except in writing and signed by the Seller. The Seller makes no representation that the goods comply with any present or future federal, state or local regulation or ordinance. Compliance is the Buyer s responsibility. The use of the Seller s goods should be in accordance with the provision of the National Electrical Code, UL and/or other industry or military standards that are pertinent to the particular end use. Installation or use not in accordance with these codes and standards could be hazardous. North America Headquarters 203 Cooper Circle Peachtree City, GA P: F: ControlsSales@cooperindustries.com International Headquarters 20 Greenhill Crescent Watford Business Park Watford, Herts, WD18 8XG. UK P: +44 (0) F: +44 (0) enquiries@coopercontrols.co.uk Document IM8896 Iss.01