NSSM124T Pb-free Reflow Soldering Application RoHS Compliant RGB Sorted (RGB die lit separately.)

Transcription

1 NICHIA CORPORATION SPECIFICATIONS FOR FULL COLOR LED NSSM124T Pb-free Reflow Soldering Application RoHS Compliant RGB Sorted (RGB die lit separately.)

2 SPECIFICATIONS (1) Absolute Maximum Ratings Absolute Maximum Rating Item Symbol Blue Green Red Unit Forward Current I F ma Pulse Forward Current I FP ma Reverse Voltage V R 5 V Power Dissipation P D mw Total Power Dissipation P TOT 150 mw Operating Temperature T opr -30~85 C Storage Temperature T stg -40~100 C Junction Temperature T J C * Absolute Maximum Ratings at T A =25 C. * I FP conditions with pulse width 10ms and duty cycle 10%. * The absolute maximum Power Dissipation per die. * The absolute maximum Power Dissipation in total per package. (2) Initial Electrical/Optical Characteristics Typ Item Symbol Condition Blue Green Red Unit Forward Voltage V F B I F =20mA G I F =20mA V R I F =20mA Reverse Current I R B V R =5V G V R =5V μa R V R =5V Luminous Intensity I V B I F =20mA G I F =20mA R I F =20mA mcd x B I F =20mA Chromaticity Coordinate - G I F =20mA - y R I F =20mA * Characteristics at T A =25 C. * Luminous Intensity value as per CIE 127:2007 standard. * Chromaticity Coordinates as per CIE 1931 Chromaticity Chart. 1

3 RANKS Item Blue Green Red Min Max Min Max Min Max Unit Forward Voltage V Reverse Current μa Luminous Intensity mcd Color Rank Blue Rank W x y Green Rank G0d x y Red Rank R x y * Ranking at T A =25 C. * Forward Voltage Tolerance: ±0.05V * Luminous Intensity Tolerance: ±10% * Chromaticity Coordinate Tolerance: ±0.01 2

4 CHROMATICITY DIAGRAM G0d y R W x 3

5 OUTLINE DIMENSIONS ± 0.1 (0.7)(0.7) (2.55) 3 4

6 SOLDERING Recommended Reflow Soldering Condition(Lead-free Solder) Recommended Hand Soldering Condition Temperature Soldering Time 350 C Max 3sec Max 1 to 5 C per sec Pre-heat 180 to 200 C 60sec Max Above 220 C 260 CMax 10sec Max 120sec Max Recommended Soldering Pad Pattern * This LED is designed to be reflow soldered on to a PCB. If dip soldered, Nichia cannot guarantee its reliability. * Reflow soldering must not be performed more than twice. Hand soldering must not be performed more than once. * If the LEDs are reflowed a second time, it is recommended to perform the second soldering as soon as the LEDs have cooled down to room temperature naturally after the first soldering in order to avoid moisture absorption. * Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature. * Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation, caused by heat and/or atmosphere. * Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. * When soldering, do not apply stress to the LED while the LED is hot. * When using a pick and place machine, choose an appropriate nozzle for this product. * This product can differ in optical characteristics depending on both the number of reflow cycles and reflow temperature conditions. In a single display, only LEDs with both the same number of reflow cycles and reflow temperature conditions should be used regardless of the application type (e.g. rental and/or permanent installations). * The recommended soldering pad pattern is designed for attachment of the LED without problems. When precise mounting accuracy is required, such as high-density mounting, ensure that the size and shape of the pad are suitable for the circuit design. * Consider factors such as the reflow soldering temperature, hand soldering temperature, etc. when choosing the solder. * When flux is used, it should be a halogen free flux. Ensure that the manufacturing process is not designed in a manner where the flux will come in contact with the LEDs. * Make sure that there are no issues with the type and amount of solder that is being used. 5

7 TAPE AND REEL DIMENSIONS テーピング部 Tape Φ ±0.1 2 ± ± ±0.05 管理番号 No. Nxxx124x STS-DA7-0042A ( 単位 Unit: mm) Pin-1 Mark 3.5 ± ±0.1 4 ±0.1 Φ ± ±0.1 トレーラ部 / リーダ部 Trailer and Leader エンボスキャリアテープ Embossed Carrier Tape トップカバーテープ Top Cover Tape 引き出し方向 Feed Direction トレーラ部 MIN 160mm( 空部 ) Trailer 160 mm MIN (Empty Pockets) リール部 Reel Φ 21 ±0.8 f 21 ± LED 装着部 Loaded Pockets 11.4 ±1 9 ±0.3 引き出し部 MIN 100mm( 空部 ) Leader with Top Cover Tape 100 mm MIN (Empty Pocket) リーダ部 MIN 400mm Leader without Top Cover Tape 400 mm MIN * 数量は1リールにつき 3500 個入りです Reel Size: 3500pcs * JIS C 0806 電子部品テーピングに準拠しています The tape packing method complies with JIS C 0806 (Packaging of Electronic Components on Continuous Tapes). ラベル Label f 13 ±0.2 Φ 13 ±0.2 Φ * 実装作業の中断などでエンボスキャリアテープをリールに巻き取る場合 エンボスキャリアテープを強く (10N 以上 ) 締めないで下さい LEDがカバーテープに貼り付く可能性があります When the tape is rewound due to work interruptions, no more than 10N should be applied to the embossed carrier tape. The LEDs may stick to the top cover tape. 6

8 PACKAGING - TAPE & REEL 7

9 LOT NUMBERING CODE Lot Number is presented by using the following alphanumeric code. YMxxxx - RRR Y - Year Year Y 2014 E 2015 F 2016 G 2017 H 2018 I 2019 J M - Month Month M Month M A B C xxxx-nichia's Product Number RRR-Rank * The label does not have the RANK field for un-ranked products. 8

10 DERATING CHARACTERISTICS 管理番号 No. NSSM124x STS-DA7-0043B 周囲温度 - 許容損失特性 * Ambient Temperature vs Power Dissipation Derating1 250 BLUE GREEN RED 周囲温度 - 全許容損失特性 Ambient Temperature vs Total Power Dissipation 250 ** Derating2 許容損失 Power Dissipation(mW) (32, 124)GREEN (38, 127)RED 100 (47, 88.7)BLUE (85, 30.0)RED 50 (85, 27.0)GREEN (85, 25.0)BLUE 周囲温度 Ambient Temperature( C) 全許容損失 Total Power Dissipation(mW) 200 (40, 150) (85, 37.5) 周囲温度 Ambient Temperature( C) デューティー比 - 許容順電流特性 Duty Ratio vs Allowable Forward Current 1000 Duty T A =25 C BLUE GREEN RED 許容順電流 Allowable Forward Current(mA) デューティー比 Duty Ratio(%) * ** 多色点灯の際も 1 素子当たりの値はこの定格内におさめて下さい The graph shows the maximum allowable power dissipation for a LED die of each color. 2 素子以上点灯の際は トータル値を定格内におさめて下さい The graph shows the maximum allowable total power dissipation for a LED package. 9

11 OPTICAL CHARACTERISTICS * 本特性は参考です All characteristics shown are for reference only and are not guaranteed. 発光スペクトル Spectrum Spectrum 管理番号 No. NSSM124 STS-DA 相対発光強度 Relative Emission Intensity (a.u.) 波長 Wavelength (nm) Directivity1 T A = 25 C BLUE ( I F = 20 ma) GREEN ( I F = 20 ma) RED ( I F = 20 ma) 指向特性 Directivity X-X T A = 25 C 放射角度 Radiation Angle BLUE ( I FP = 20 ma) GREEN ( I FP = 20 ma) RED ( I FP = 20 ma) X (-90 ) Y(90 ) X (90 ) Y(-90 ) 相対光度 Relative Luminosity (a.u.) 90 Y-Y Directivity T A = 25 C 放射角度 Radiation Angle BLUE ( I FP = 20 ma) GREEN ( I FP = 20 ma) RED ( I FP = 20 ma) 相対光度 Relative Luminosity (a.u.) 90 10

12 FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です All characteristics shown are for reference only and are not guaranteed. 管理番号 No. NSSM124x STS-DA7-0045A 順電圧 - 順電流特性 Forward Voltage vs Forward Current 1000 VfIf T A =25 C BLUE GREEN RED 周囲温度 - 順電圧特性 Ambient Temperature vs Forward Voltage 5.0 TaVf BLUE GREEN RED I FP = 20mA I FP = 20mA I FP = 20mA 4.5 順電流 Forward Current(mA) 順電圧 Forward Voltage(V) 順電圧 Forward Voltage(V) 周囲温度 Ambient Temperature( C) 順電流 - 相対光度特性 Forward Current vs Relative Luminosity 7 IfIv T A =25 C BLUE GREEN RED 周囲温度 - 相対光度特性 Ambient Temperature vs Relative Luminosity 1.4 TaIvBLUE GREEN RED I FP = 20mA I FP = 20mA I FP = 20mA 6 相対光度 Relative Luminosity(a.u.) 相対光度 Relative Luminosity(a.u.) 順電流 Forward Current(mA) 周囲温度 Ambient Temperature( C) 11

13 RELIABILITY (1) Tests and Results Failure Test Reference Test Units Test Conditions Criteria Standard Duration Failed/Tested # Resistance to JEITA ED-4701 T sld =260 C, 10sec, 2reflows, Soldering Heat #1 0/ Precondition: 30 C, 70%RH, 168hr (Reflow Soldering) Temperature Cycle JEITA ED C(30min)~25 C(5min)~ C(30min)~25 C(5min) 100cycles #1 0/50 Moisture Resistance JEITA ED C~65 C~-10 C, 90%RH, (Cyclic) hr per cycle 10cycles #1 0/50 High Temperature JEITA ED-4701 Storage T A =100 C 500hours #1 0/50 Temperature Humidity JEITA ED-4701 Storage T A =60 C, RH=90% 500hours #1 0/50 Low Temperature JEITA ED-4701 Storage T A =-40 C 500hours #1 0/50 B I F =9mA Room Temperature Operating Life T A =25 C G I F =14mA 500hours #1 0/50 R I F =18mA B I F =5mA Temperature Humidity Operating Life 60 C, RH=90% G I F =11mA 500hours #1 0/50 R I F =11mA B I F =9mA Low Temperature Operating Life T A =-30 C G I F =14mA 500hours #1 0/50 R I F =18mA NOTES: Measurements are performed after allowing the LEDs to return to room temperature. (2) Failure Criteria (Value for one LED device (Single color).) Criteria # Items Conditions Failure Criteria Forward Voltage(V F ) B I F =20mA G I F =20mA >U.S.L. 1.1 R I F =20mA #1 Luminous Intensity(I V ) B I F =20mA G I F =20mA <L.S.L 0.7 R I F =20mA Reverse Current(I R ) B V R =5V G V R =5V R V R =5V >U.S.L. 2.0 U.S.L. : Upper Specification Limit L.S.L. : Lower Specification Limit 12

14 CAUTIONS (1) Storage Conditions Temperature Humidity Time Before Opening Aluminum Bag 30 C 90%RH Within 1 Year from Delivery Date Storage After Opening Aluminum Bag 30 C 70%RH 168hours Baking 65±5 C - 24hours Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details. Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination and result in optical performance degradation. Products are packed in moisture-proof aluminum bags to minimize moisture absorption during transportation and storage. Included silica gel desiccants change from blue to red if moisture had penetrated bags. After opening the moisture-proof aluminum bag, the products should go through the soldering process within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants in a hermetically sealed container, preferably the original moisture-proof bags for storage. After the Period After Opening storage time has been exceeded or silica gel desiccants are no longer blue, the products should be baked. Baking should only be done once. The leads or electrode pads (anode and cathode) of the product are plated with silver. Exposure to a corrosive environment might cause the silver plated the leads or electrode pads to tarnish, and thus leading to difficulties in soldering. If unused LEDs remain, they must be stored in a hermetically sealed container. Nichia recommends using the original moisture-proof bag for storage. Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur. The extremely corroded or contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended as a material for seals. Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts inside the products, caused by low molecular weight volatile siloxane. To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions. Do not store the LEDs in a dusty environment. Do not expose the LEDs to direct sunlight and/or an environment where the temperature is higher than normal room temperature. (2) Directions for Use In designing a circuit, the current through each LED die must not exceed the Absolute Maximum Rating current specified for each die. It is recommended that each LED die is driven at a constant current. When having the two or more dice within this product on at the same time, the total power dissipation for the LED package must be within the absolute maximum value specified in this specification. This product should be operated using forward current. Ensure that the product is not subjected to either forward or reverse voltage while it is not in use. In particular, subjecting it to continuous reverse voltage may cause migration, which may cause damage to the LED die. When used in displays that are not used for a long time, the main power supply should be switched off for safety. It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics. Care must be taken to ensure that the reverse voltage will not exceed the Absolute Maximum Rating when using the LEDs with matrix drive. Ensure that excessive voltages such as lightning surges are not applied to the LEDs. This product is specifically designed for indoor applications. For outdoor use, necessary measures should be taken to prevent direct sunlight, water, moisture and salt air damage. 13

15 (3) Handling Precautions Do not handle the LEDs with bare hands as it will contaminate the LED surface and may affect the optical characteristics: it might cause the LED to be deformed and/or the wire to break, which will cause the LED not to illuminate. The lead could also cause an injury. When handling the product with tweezers, be careful not to apply excessive force to the resin. Otherwise, The resin can be cut, chipped, delaminate or deformed, causing wire-bond breaks and catastrophic failures. Dropping the product may cause damage. Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped, delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures. (4) Design Consideration PCB warpage after mounting the products onto a PCB can cause the package to break. The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist. The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines. The LED should be placed in a way to minimize the stress on the LEDs due to board flexing. Board separation must be performed using special jigs, not using hands. (5) Electrostatic Discharge (ESD) The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials Ensure that tools (e.g. soldering irons), jigs and machines that are being used are properly grounded and that proper grounding techniques are used in work areas. For devices/equipment that mount the LEDs, protection against surge voltages should also be used. If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers The customer is advised to check if the LEDs are damaged by ESD when performing the characteristics inspection of the LEDs in the application. Damage can be detected with a forward voltage measurement or a light-up test at low current ( 1mA). LEDs with ESD-damaged dice (i.e. other than red) may have an increased leakage current, current flow at a low voltage, or no longer illuminate at a low current. Failure Criteria: V F <2.0V at I F =0.5mA (6) Thermal Management Proper thermal management is an important when designing products with LEDs. LED die temperature is affected by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature does not exceed the maximum Junction Temperature (T J ). Drive current should be determined for the surrounding ambient temperature (T A ) to dissipate the heat from the product. (7) Cleaning The LEDs should not be cleaned with water, benzine, and/or thinner. If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs due to the damage to the resin portion. The effects of such solvents should be verified prior to use. In addition, the use of CFCs such as Freon is heavily regulated. When dust and/or dirt adheres to the LEDs, soak a cloth with Isopropyl alcohol (IPA), then squeeze it before wiping the LEDs. Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs depending on the ultrasonic power and how LED is assembled. If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning. 14

16 (8) Eye Safety In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps and lamp systems, which added LEDs in its scope. On the other hand, the IEC :2007 laser safety standard removed LEDs from its scope. However, please be advised that some countries and regions have adopted standards based on the IEC laser safety standard IEC : , which still includes LEDs in its scope. Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1. High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2. Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs with optical instruments which may greatly increase the damages to your eyes. Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product, please be careful to avoid adverse effects on the human body caused by light stimulation. (9) Others The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles, traffic control equipment, life support systems and safety devices). The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis. The specifications and appearance of this product may change without notice; Nichia does not guarantee the contents of this specification. Both the customer and Nichia will agree on the official specifications of supplied products before the volume production of a program begins. 15