3.3V / 1310 nm / 1.25 Gbps Digital Diagnostic LC SFP SINGLE-MODE TRANSCEIVER

Transcription

1 / SPS-7110AWG (RoHS Compliant).V / 110 nm / 1. Gbps Digital Diagnostic LC SFP SINGLE-MODE TRANSCEIVER ********************************************************************************************************************************************************************** FEATURES Hot-Pluggable SFP Footprint LC Optical Transceiver Small Form-Factor Pluggable (SFP) MSA compatible Compliant with IEEE 80.z 1000BASE-LX Compliant with Fibre Channel 1x SM-LC-L FC-PI SFF-87 Digital Diagnostic Function AC/AC Coupling according to MSA Distance up to 10 km Single +. V Power Supply RoHS Compliant -10 to o C Operation: -0 to o C Operation: SPS-7110AWG Class 1 Laser International Safety Standard IEC-608 Compliant APPLICATIONS Gigabit Ethernet Switches and Routers Fibre Channel Switch Infrastructure XDSL Applications Metro Edge Switching ORDER INFORMATION P/No. Bit Rate (Gb/s) 1000 BASE Distance (km) Wavelength (nm) DESCRIPTION The series single mode transceivers are small form factor pluggable module for bi-directional serial optical data communications such as Gigabit Ethernet 1000BASE-LX and Fibre Channel 1x SM-LC-L FC-PI. It is with the SFP 0-pin connector to allow hot plug capability. Digital diagnostic functions are available via an I C. This module is designed for single mode fiber and operates at a nominal wavelength of 110 nm. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-608. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-608 and FDA 1 CFR and The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. Package Temp. ( o C) TX Power (dbm) RX Sens. (dbm) 1 RoHS Compliant 1. LX / LH LC SFP with DMI -10 to - to Yes SPS-7110AWG 1. LX / LH LC SFP with DMI -0 to - to Yes Absolute Maximum Ratings Parameter Symbol Min Max Units Notes Storage Temperature Tstg -0 o C Operating Case Temperature Topr o C SPS-7110AWG Power Supply Voltage Vcc V Recommended Operating Conditions Parameter Symbol Min Typ Max Units / Notes Power Supply Voltage Vcc.1.. V Operating Case Temperature Topr o C / C / SPS-7110AWG Power Supply Current I CC (TX+RX) ma Data Rate Mb/s

2 Transmitter Specifications (-10 o C < Topr < o C,.1V < Vcc <.V) Parameter Symbol Min Typ Max Units Notes Optical Optical Transmit Power Po dbm 1 Output Center Wavelength nm Output Spectrum Width nm RMS (σ) Extinction Ratio E R db Optical Rise Time t r 60 ps 0 % to 80% Values Optical Fall Time t f 60 ps 0 % to 80% Values Relative Intensity Noise RIN -10 db/hz Electrical Data Input Current Low I IL -0 A Data Input Current High I IH 0 A Differential Input Voltage V IH - V IL 0.. V Peak-to-Peak TX Disable Input Voltage Low T DIS, L 0 0. V TX Disable Input Voltage High T DIS, H.0 Vcc V TX Disable Assert Time T ASSERT 10 s TX Disable Deassert Time T DEASSERT 1 ms TX Fault Output Voltage -- Low T FaultL 0 0. V TX Fault Output Voltage -- High T FaultH.0 Vcc+0. V 1. Output power is power coupled into a 9/1 m single mode fiber.. There is an internal.7k to 10K ohm pull-up resistor to VccTX.. Open collector compatible,.7k to 10K ohm pull-up to Vcc (Host Supply Voltage). Receiver Specifications (-10 o C < Topr < o C,.1V < Vcc <.V) Parameter Symbol Min Typ Max Units Notes Optical Sensitivity Sens -1 dbm Maximum Input Power Pin - dbm Signal Detect -- Asserted Pa dbm Transition: low to high Signal Detect -- Deasserted Pd dbm Transition: high to low Signal detect -- Hysteresis db Wavelength of Operation nm Electrical Differential Output Voltage V OH V OL V Output LOS Voltage -- Low V OL 0 0. V Output LOS Voltage High V OH.0 Vcc+0. V. Measured at 7-1 PRBS at BER 100 nm.. Open collector compatible,.7k to 10K ohm pull-up to Vcc (Host Supply Voltage).

3 CONNECTION DIAGRAM PIN Signal Name Description PIN Signal Name Description 1 TX GND Transmitter Ground 11 RX GND Receiver Ground TX Fault Transmitter Fault Indication 1 RX DATA OUT- Inverse Receiver Data Out TX Disable Transmitter Disable (Module disables on high or open) 1 RX DATA OUT+ Receiver Data Out MOD-DFE Modulation Definition Two wires 1 RX GND Receiver Ground serial ID Interface MOD-DEF1 Modulation Definition 1 Two wires 1 Vcc RX Receiver Power.V±% serial ID Interface 6 MOD-DEF0 Modulation Definition 0 Ground in 16 Vcc TX Transmitter Power.V±% Module 7 N/C Not Connected 17 TX GND Transmitter Ground 8 LOS Loss of Signal 18 TX DATA IN+ Transmitter Data In 9 RX GND Receiver Ground 19 TX DATA IN- Inverse Transmitter Data In 10 RX GND Receiver Ground 0 TX GND Transmitter Ground Module Definition Module Definition MOD-DEF PIN MOD-DEF1 PIN MOD-DEF0 PIN 6 Interpretation by Host SDA SCL LV-TTL Low Serial module definition protocol Module Definition specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the -wire serial CMOS E PROM protocol of the ATMEL ATC01A/0/0 family of components.

4 D Optoway 1 RECOMMENDED CIRCUIT SCHEMATIC (1,17,0) VeeT Tx_DISABLE Tx_DISABLE Tx_FAULT Tx_FAULT C LD Driver 100Ω TD + TD - VccT VccR μH 1μH Vcc.V TD + TD - SerDes IC Protocol IC RD Ω RD - POST Amp RD + LOS 1 8 RD + depending on SERDES LOSS OF SINGAL VeeR MOD_DEF(0) (9,10,11,1) 6 MODULE DETECT B EEPROM MOD_DEF(1) SCL MOD_DEF() SDA SFP module Vcc.V PACKAGE DIAGRAM Units in mm A Title Size Number B Date: File: -Dec-006 D:\WORK\sch.ddb 1 Note: Specifications subject to change without notice.

5 Revision History Version Subject Release Date 1.0 Initial datasheet 00/1/1.0 Revise package diagram for high port density use 008/1/1