PAVIRO End Of Line Slave Module

Transcription

1 PAVIRO End Of Line Slave PVA-1WEOL en Installation note

2

3 PAVIRO End Of Line Slave Table of Contents en 3 Table of contents 1 Short information 4 2 Installation 5 3 Technical data 9 4 Standards and compliancy 13

4 4 en Short information PAVIRO End Of Line Slave 1 Short information The End Of Line (EOL) Slave monitors the integrity of a loudspeaker line. In combination with the EOL master, integrated in every Controller and Router of the PAVIRO system, the loudspeaker line can be monitored against short-circuit or opencircuit. The status LED of the module can help to check the installation. Please refer to the documentation of IRIS-Net or the Controller/Router for more details. Parts included Quantity Component 1 PVA-1WEOL 1 Set of screws 1 Installation note

5 PAVIRO End Of Line Slave Installation en 5 2 Installation Before connecting the module, a module address must be set via the DIP switches S2 and S1 (see following illustration). The module address allows for identification of the affected loudspeaker line in case an error (e.g. open-circuit) occurred. 1 2 Figure 2.1: Location of the DIP switches ➊ and the Status LED ➋ at the module Notice! The module address must be unique within each zone topology (each controller or router).

6 6 en Installation PAVIRO End Of Line Slave DIP switch S2 DIP switch S1 address OFF OFF OFF OFF OFF OFF 0 (not connected) OFF OFF OFF OFF OFF ON 1 OFF OFF OFF OFF ON OFF 2 OFF OFF OFF OFF ON ON 3 OFF OFF OFF ON OFF OFF 4 OFF OFF OFF ON OFF ON 5 OFF OFF OFF ON ON OFF 6 OFF OFF OFF ON ON ON 7 OFF OFF ON OFF OFF OFF 8 OFF OFF ON OFF OFF ON 9 OFF OFF ON OFF ON OFF 10 OFF OFF ON OFF ON ON 11 OFF OFF ON ON OFF OFF 12 OFF OFF ON ON OFF ON 13

7 PAVIRO End Of Line Slave Installation en DIP switch S2 DIP switch S1 address OFF OFF ON ON ON OFF 14 OFF OFF ON ON ON ON 15 OFF ON OFF OFF OFF OFF 16 OFF ON OFF OFF OFF ON 17 : : : : : : ON ON ON ON OFF OFF 60 OFF Reserved ON OFF To activate the ON status LED for five minutes, switch from ON to OFF Table 2.1: DIP switch settings on the module (the settings on delivery are shown in bold)

8 8 en Installation PAVIRO End Of Line Slave Status LED Off Slow flashing (2 Hz) Rapid flashing (10 Hz) Description No voltage supply (e.g. pilot tone deactivated) ready Data is being received from EOL master Table 2.2: Status LED for checking installation! Caution! Please ensure that all safety regulations are observed. Mounting the module on spacers is strongly recommended.

9 PAVIRO End Of Line Slave Technical data en 9 3 Technical data Power supply Minimum R G (resistance between speaker line and ground) Maximum C G using successive numbers (capacity between speaker line and ground) Maximum number of modules allowed is 60 Maximum number of modules allowed is 58 Maximum C G using even or odd numbers (capacity between speaker line and ground) Maximum number of modules allowed is khz, 8 V eff, 20 mw 1.5 MΩ / 3.0 MΩ (FW / 1.2.0) Hardware version 1.1 Firmware version = 400 nf Hardware version 1.1 Firmware version = 400 nf Hardware version 1.1 Firmware version = 400 nf Hardware version 1.1 Firmware version = 1200 nf Operating temperature -5 C to +45 C

10 10 en Technical data Product dimensions (Width Height Depth) Net weight PAVIRO End Of Line Slave mm 30 g Speaker + + Filter DC/DC R G C G Speaker - Shield / Wire / Ground - - Send/ Receive Control Address Figure 3.1: Circuit diagram (R G and C G are caused by the loudspeaker installation, e.g. wire type, length)

11 PAVIRO End Of Line Slave Technical data en 11 Notice! Depending on the audio route, the EOL modules might be in parallel with an amplifier channel. The capacitance for any EOL module that might be in parallel to one (amplifier) channel must be added to the total capacitance. Ensure that the worst case situation does not exceed the maximum allowed capacitance. A capacitance calculator to check if the capacitance is in the safe zone and an additional application note can be found on the Bosch Security website.

12 12 en Technical data PAVIRO End Of Line Slave Figure 3.2: Wiring diagram C G = C 1 + C 2 + C 3

13 PAVIRO End Of Line Slave Standards and compliancy en 13 4 Standards and compliancy The device meets the following standards (as of November 2015): IEC EN EN EN FCC ICES-003 EN FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ICES-003 This class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

14

15

16 Bosch Security Systems B.V. Torenallee BA Eindhoven Netherlands Bosch Security Systems B.V., 2016