DA-Type Socket Assemblies
|
|
- Jeffrey Owen
- 6 years ago
- Views:
Transcription
1 DA-Type Socket Assemblies Socket Assemblies with Transimpedance Amplifier (DA Type) DA type socket assemblies contain an active voltage-divider circuit and an amplifier that converts high impedance current signals from the photomultiplier tube into low impedance voltage signals. These socket assemblies ensure stable photomultiplier operation with excellent output linearity. Features Active Voltage Divider Superior DC Output Linearity Photomultiplier Tube Gain Adjustment Function (C7246 series) Wide Frequency Bandwidth (C7247 series) /output Connectors (C , C , C , C ) Specifications Type No. C7246- C C7247- C C7246 C C7247 C Applicable s 28 mm Side-on type 28 mm Head-on type R374, R2228, R929, R694, R69, etc. Voltage ±2 to ± Voltage ±8 Supply Voltage (ma) +2/-.3 +4/- +2/-.3 +4/- Amplifier Frequency Bandwidth (-3 db) DC to 2 khz DC to MHz DC to 2 khz DC to MHz Current to Voltage Conversion Factor (V/µA).3 kω). Ω).3 kω). Ω) Output Signal Voltage + kω) +3 Ω) + kω) +3 Ω) NOTE: AIf the output signal voltage is 3 V or higher (with kω load), the divider circuit input voltage should be -6 V to - V. Frequency Response of Built-in Amplifier C7246/-/-22/-23 C7247/-/-22/-23 TACCB46EB TACCB6EA RELATIVE GAIN (db) dB RELATIVE GAIN (db) dB FREQUENCY (khz) FREQUENCY (MHz) Circuit Diagrams C7246 (- B /-22/-23 B ) C7247 (- B /-22/-23 B ) K DY DY2 DY3 DY4 DY DY6 DY7 DY8 DY9 DY DY P Ω SIGNAL OUTPUT K DY DY2 DY3 DY4 DY DY6 DY7 DY8 DY9 DY DY P Ω SIGNAL OUTPUT C C2 C3 C4 C C2 C3 C4 ACTIVE DIVIDER C, C2: nf C3: 22 nf C4: 47 nf ACTIVE DIVIDER C, C2: nf C3: 22 nf C4: 47 nf -HV VR = MΩ * GAIN ADJ. CIRCUIT * PATENT -HV NOTE: BC7247-/-23 are for 28 mm side-on so that the last dynode number is "DY9" 2 NOTE: BC7246-/-23 are for 28 mm side-on so that the last dynode number is "DY9" TACCC3EC TACCCEB
2 Amplifier Offset Output Noise Voltage Voltage Max. (mv) Typ. (mv rms) ± ±3 ± ±3.9 kω) 4. Ω).9 kω) 4. Ω) Voltage-divider Circuit Recommended Divider Supply Voltage Supply Voltage Current (µa) -3 to - A -3 to -6-4 to - A -4 to -9-2 (HV = - V) 66 (HV = -6 V) 74 (HV = - V) 29 (HV = -9 V) Gain Adjustable Range (db) 3 Operating Ambient Temprature Storage to +4 - to +6 Weight (g) Dimensional Outlines (Unit : mm) C7246/-22, C7247/-22 [BOTTOM VIEW] C7246/-22 C7246-/-23, C7247-/ ±.3 3. [BOTTOM VIEW] C7246-/ ± ) POT (VR) GAIN ADJ ± ± ±.3 ) POT (VR) GAIN ADJ ±. C7247/ ± ±.3 C7247-/-23. TACCA7EF. TACCA97ED Type No. Cable Type Cable Length Connector C7246/- C7247/- C /-23 C /-23 /output -HV SHIELD CABLE 2) (GRAY) Signal Output COAXIAL CABLE: RG-74/U (BLACK) ± V TWISTED PAIR CABLE WITH SHIELD 3) (GRAY) -HV SHIELD CABLE (GRAY) Signal Output ± V COAXIAL CABLE: RG-74/U (BLACK) TWISTED PAIR CABLE WITH SHIELD (GRAY) 4 ± ± 2 SHV-P BNC-P DIN (6 PIN)-P NOTES: ) Turning this pot clockwise decreases the gain. (2 turns max.) 2) At the end of HV cable, it's possible to attach SHV connector fitting RG-74/U. 3) Connect as follow. WHITE... - V ORANGE... + V SHIELD... * See page 2 for details on flanges and housing contains a magnetic shield case. 3
3 DP-Type Socket Assemblies High Voltage Power Supply Socket Assemblies (DP Type) DP type socket assemblies include a high voltage power supply and so allow easily operating a photomultiplier tube just by supplying a low voltage (+ V or + V). These socket assemblies ensure highly stable photomultiplier tube operation with excellent output linearity. Features Superior DC Output Linearity Active Voltage Divider (C297-, C33-, C34-) Fast High Voltage Programming Response (C297-, C33-, C34-) Cockcroft-Walton Circuit (C899, C899-, C344-3, C2842-, C2842-2) Low Power Consumption (C899, C899-, C344-3, C2842-, C2842-2) Specifications Type No. Applicable s Voltage Voltage B Current (ma) Linear DC Anode E Output Current Ripple Noise Min. (µa) Typ. (mvp-p) C ± 6 C. C899 C899- C33- C34- C mm side-on type 2 mm head-on type R924A, R92A, R3A, R7A, etc. 28 mm head-on type R374, R2228, R929, R694, R69, etc. +. to to +. + ± +. to +. C2842- A 8 stage dynode, head-on type R623, R6232, R6233, R6234, R623, R6236, R6237, etc. C A stage dynode, head-on type R878, R, R94, R877, R2, R3, etc. NOTE: A C2842-S/-2S which is with shutter(ms to DC) function are also available. Please refer the individual datasheet for details. B When photomultiplier tube is not attached. + ± D C D D...6 (Max.) C Supply Voltage: - V, Within: ±2 % linearity D Supply Voltage: - V, Within: ±. % linearity E Load resistance= MΩ, Load capacitance=2 pf to 2 pf DEVIATION (%) DC Linearity Characteristics 2 - TACCB2EB 33 kω / STAGE SUPPLY : - V C899/-, C344-3 C2842-/-2 Schematic Diagrams C297- C33- C34- OUTPUT CURRENT (µa) C297-, C33-, C34- OUTPUT CURRENT (µa) Practical DC Output Limits TACCB3EC C899/-, C344-3 C2842-/-2 33 kω / STAGE SUPPLY * * Photomultiplier tube must be used with a supply voltage within the rated range. C899 C899- C344-3 C34- C297- C OUTPUT High Voltage Controlling Characteristics TACCB4EE C297-, C33- C34- C899* C899- C344-3 C2842-/ CONTROL C2842- C * C899 can be controlled up to +.2 V (output voltage -2 V) (C297-, C33-, C34-) (C899/-, C344-3, C2842-/-2) ACTIVE DIVIDER HIGH POWER SUPPLY.8 kω.8 kω + V IN (RED) (BLACK) Vref (+ V) OUT (BLUE) : C297-, C33- Vref (+6 V) OUT (BLUE) : C34- (BLACK) COCKCROFT- WALTON CIRCUIT (HIGH DIVIDER) HIGH ADJUSTMENT CIRCUIT 6.2 kω + V IN (RED) Vref (+2. V) OUT (C899-, C344-3) (BLUE) Vref (+.2 V) OUT (C899) (BLUE) (BLACK) COCKCROFT- WALTON CIRCUIT (HIGH DIVIDER) HIGH ADJUSTMENT CIRCUIT 6.2 kω + V IN (RED) Vref (+2. V) OUT (BLUE) (BLACK) 4 TACCC22EB TACCC4EA TACCC67EA
4 Output Voltage Range - to -2 F -2 to -2 F -2 to - F -2 to -2 F -2 to - F -2 to - F Linear Regulation Typ. (%) ±. G High Voltage Power Supply Output H Output Voltage Voltage Programing Control Response Typ. (ms) V to + V or 8 external kω potentiometer V to +.2 V or external kω potentiometer V to +. V or external kω potentiometer V to + V or external kω potentiometer 8 V to +6 V or external kω potentiometer V to +. V or external kω potentiometer Settling Time (s) I Coefficient Typ. (%/ C) ±. ±. ±. ±. Operating Ambient to + to + to +4 to + Storage - to +6 Weight (g) to - V to +. V or external kω potentiometer ±. to + 76 F Output voltage that guarantees the characteristics. G Against ± V input change H for %/99 % HV change I The time required for the output to reach a stable level following a change in the control voltage from +. V to +. V. Dimensional Outlines (Unit: mm) C297- C33- C34- C899 C899- C344-3 C2842-/ ± ± ± ±. 4 MIN. 3.8 ± ±. 4 MIN. 3.8 ±. 4. ± ±. 4 ± ± ± ± ±.3 3. ±. 4 MIN ±. 33. ± ± ± ± ±. 4 ± ±.3. + V INPUT AWG 24, RED + V INPUT AWG 24, RED + V INPUT AWG 24, RED SIGNAL OUTPUT + V INPUT Vref OUTPUT HV CONTROL INPUT COAXIAL CABLE RG-74/U AWG 24, RED AWG 24, BLUE AWG 24, WHITE + V INPUT AWG 24, RED + V INPUT AWG 26, RED Vref OUTPUT AWG 26, BLUE HV CONTROL INPUT AWG 26, WHITE AWG 26, BLACK TACCA328EA TACCA329EA TACCA33JA TACCA3EE TACCA294EA TACCA323EA * See page 2 for details on flanges and housing contains a magnetic shield case.
5 DAP-Type Socket Assemblies High Voltage Power Supply Socket Assemblies with Transimpedance Amplifier (DAP Type) DAP type socket assemblies contain an high voltage power supply and an amplifier that converts high impedance current signals from the photomultiplier tube into low impedance voltage signals. These socket assemblies ensure stable photomultiplier operation with excellent output linearity. Features Superior DC Output Linearity Active Voltage Divider (, C79, C79-) Fast High Voltage Programming Response (, C79, C79-) Cockcroft-Walton Circuit (C2843-, C2843-2) Low Power Consumption (C2843-, C2843-2) Wide Frequency Bandwidth (C79, C79-) Single Power Supply Operation () Specifications Type No. Applicable s Voltage Voltage Current (ma) + ± +8 +6/ 28 mm side-on type C79 ± ± ±8 +6/-2 28 mm head-on type C79- R374, R2228, R929, R694, R69, etc. C2843- A 8 stage dynode, head-on type R623, R6232, R6233, R6234, R623, R6236, etc. ± ±. ±6 +6./-3. C A stage dynode, head-on type R878, R, R94, R877, R2, R3, etc. NOTE: A C2843-S/-2S which is with shutter(ms to DC) function are also available. Please refer the individual datasheet for details. B When photomultiplier tube is not attached. B Linear DC Output Current Min. (µa) 43 kω) C 8 Ω) D 4 kω) E Frequency Bandwidth (-3 db) DC to khz DC to MHz DC to 2 khz Amplifier Current to Voltage Output Conversion Factor Signal Voltage (V/µA).3 +3 kω) kω). +.2 Ω) Ω). +4 kω) kω) C Supply Voltage: - V, Within: ±2 % linearity D Supply Voltage: -9 V, Within: ±2 % linearity E Supply Voltage: - V, Within: ±. % linearity DEVIATION (%) DC Linearity Characteristics TACCB4EB 2 SUPPLY : - V (, C2843-/-2) -9 V (C79, C79-) C79/- 33 kω / STAGE C2843-/-2 OUTPUT CURRENT (µa) Practical DC Output Limits TACCBEB C79/- 33 kω / STAGE C2843-/ OUTPUT CURRENT (µa) SUPPLY High Voltage Controlling Characteristics TACCB6EB - C2843-/-2 Frequency Bandwidth TACCB8EB -2 OUTPUT C79*, C79-* RELATIVE GAIN (db) - - C2843-/2 C79/- -3 db (, C79, C79-) (C2843) CONTROL * The output is -9 V even if the control voltage is set higher than +3.6 V. -2. FREQUENCY (khz)
6 ±.3 ± Amplifier Signal Output Offset Voltage Typ. (mv) Induced Ripple on Signal Output 2 mvp-p F (Typ.) mvrms G (Typ.) Output Voltage Range to -2 to -9 Line H Regulation Typ. (%) ±. ±.3 High Voltage Power Supply Output I Output Voltage Voltage Programing Control Response Typ. (ms) V to + V or 8 external kω potentiometer V to +3.6 V 8 Settling Time (s) J Coefficient Typ. (%/ C) ±. ±.3 Operating Ambient to +4 to +4 Storage Weight (g) - to ± mvp-p F (Max.) to - ±. V to +. V or external kω potentiometer ±. to + 8 F Load resistance= MΩ, Load capacitance=2 pf to 2 pf G Load resistance= Ω, Load capacitance=2 pf H Against ± V input change I for %/99 % HV change J The time required for the output to reach a stable level following a change in the control voltage from +. V to +. V. Schematic Diagrams C79, C79- C2843-, C Ω Ω Ω - V IN (BLUE) - V IN (GREEN) ACTIVE DIVIDER.8 kω HIGH POWER SUPPLY + V IN (RED) Vref (+ V) OUT (BLUE) (BLACK) (BLACK) ACTIVE DIVIDER HIGH POWER SUPPLY + V IN (RED) (SHIELD) COCKCROFT- WALTON CIRCUIT (HIGH DIVIDER) HIGH 6.2 kω ADJUSTMENT CIRCUIT + V IN (RED) Vref (+2. V) OUT (BLUE) (BLACK) TACCC96EE TACCC2EA TACCC69EA Dimensional Outlines (Unit: mm) C79 C79- C2843-/ ± MIN R CONDUCTIVE PLASTIC 4 ± 7.7 ± ± ± ± ±.3 4 ± 6. ±. 3.7 ± ±. 4 ± V INPUT AWG 24, RED C79, C79- COAXIAL CABLE RG-74/U BLACK SIGNAL OUTPUT HV CONTROL INPUT WHITE SHIELDED CABLE GRAY ORANGE (TWISTED PAIR CABLE) SHIELD + V INPUT RED TACCA6EE SHIELDED CABLE LIGHT - V INPUT BLUE (TWISTED PAIR CABLE) BLUE SHIELD. * See page 2 for details on flanges and housing contains a magnetic shield case.. TACCA26EA + V INPUT AWG 26, RED Vref OUTPUT AWG 26, BLUE HV CONTROL INPUT AWG 26, WHITE AWG 26, BLACK - V INPUT AWG 26, GREEN TACCA337EA 7
DA-Type Socket Assemblies
DA-Type Socket Assemblies DA-TYPE ASSEMBLIES C7246 SERIES, C7247 SERIES The C7246 and C7247 series are DA type socket assemblies designed for 28 mm (1-1/8 inch) diameter side-on and head-on photomultiplier
More informationVariable-Gain High Speed Current Amplifier
Features Transimpedance (gain) switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper cut-off frequency switchable to 1 MHz, 10 MHz or full bandwidth Switchable AC/DC coupling Adjustable
More informationFirst Sensor Evaluation Board Data Sheet Part Description MOD Order #
FOTO Input + 5 DC voltage Optical input (optional C-mount for lens) Mechanical potentiometer for APD-bias setting Output 16 channels voltage signal of amplified APD (300 MHz bandwidth and additional gain
More informationPHOTOMULTIPLIER TUBE MODULES, NEW RELEASED PAMPHLET
PHOTOMULTIPLIER TUBE MODULES, NEW RELEASED PAMPHLET This pamphlet is gathered up the new released products from January 9. Photomultiplier tube (PMT) module functions are shown in the chart below. PMT
More informationVariable-Gain High Speed Current Amplifier
Features Transimpedance (Gain) Switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper Cut-Off Frequency Switchable to 1 MHz, 10 MHz or Full Bandwidth Switchable AC/DC Coupling Adjustable
More information6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable
99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using
More informationCHAPTER 8 PHOTOMULTIPLIER TUBE MODULES
CHAPTER 8 PHOTOMULTIPLIER TUBE MODULES This chapter describes the structure, usage, and characteristics of photomultiplier tube () modules. These modules consist of a photomultiplier tube, a voltage-divider
More informationUser Guide. SIB Channel MAPMT Interface Board Hamamatsu H7546 series
SIB164-1018 64 Channel MAPMT Interface Board Hamamatsu H7546 series Disclaimer Vertilon Corporation has made every attempt to ensure that the information in this document is accurate and complete. Vertilon
More informationHigh-Speed Data Communication LA310Z 8.3 GHz Differential Limiting Amplifier 16-pin Plastic QFN Package
High-Speed Data Communication LA10Z 8. GHz Differential Limiting Amplifier 16-pin Plastic QFN Package PRODUCT DESCRIPTION The LA10Z is an ultra-broadband fully differential limiting amplifier designed
More informationLOW NOISE AMPLIFIER SA SERIES
LOW NOISE AMPLIFIER SA SERIES Accurate and ultra low noise measurements of very small signals Achieve one of the highest level of low noise amplification SA600 series SA400 series Differential input SA200
More informationHigh-Speed Data Communication LA302Z 10 GHz Differential Limiting Amplifier 16-pin Plastic QFN Package
High-Speed Data Communication LA302Z 10 GHz Differential Limiting Amplifier 16-pin Plastic QFN Package PRODUCT DESCRIPTION The LA302Z is an ultra-broadband fully differential limiting amplifier designed
More informationType Ordering Code Package TAA 762 A Q67000-A2271 P-DIP-6-1 TAA 762 G Q67000-A2273 P-DSO-6-1 (SMD) TAA 765 A Q67000-A524 P-DIP-6-1
Single Operational Amplifiers TAA 762 Bipolar IC Features Wide common-mode range Large supply voltage range Large control range Wide temperature range (TAA 762) High output frequency compensation Open
More informationDual operational amplifier
DESCRIPTION The 77 is a pair of high-performance monolithic operational amplifiers constructed on a single silicon chip. High common-mode voltage range and absence of latch-up make the 77 ideal for use
More informationQuadrupole Power Supply Unit QPS400-3
http://www.cgc-instruments.de/ Quadrupole Power Supply Unit QPS400-3 Instruction Manual Document version 1.00, created on 12.07.2004 Technical Data Quadrupole Power Supply Unit 3 400 V QPS400-3 Version
More informationType Ordering Code Package TDA Q67000-A5168 P-DIP-18-5
Video Modulator for FM-Audio TDA 5666-5 Preliminary Data Bipolar IC Features FM-audio modulator Sync level clamping of video input signal Controlling of peak white value Continuous adjustment of modulation
More informationFour-Channel Sample-and-Hold Amplifier AD684
a FEATURES Four Matched Sample-and-Hold Amplifiers Independent Inputs, Outputs and Control Pins 500 ns Hold Mode Settling 1 s Maximum Acquisition Time to 0.01% Low Droop Rate: 0.01 V/ s Internal Hold Capacitors
More informationModel 176 and 178 DC Amplifiers
Model 176 and 178 DC mplifiers Features*! Drifts to 100 MΩ! CMR: 120 db @! Gain Linearity of ±.005% *The key features of this amplifier series, listed above, do not necessarily apply
More informationPIN CONFIGURATION FEATURES ORDERING INFORMATION EQUIVALENT CIRCUIT. D,F, N Packages
DESCRIPTION The µa723/µa723c is a monolithic precision voltage regulator capable of operation in positive or negative supplies as a series, shunt, switching, or floating regulator. The 723 contains a temperature-compensated
More informationLM3046 Transistor Array
Transistor Array General Description The LM3046 consists of five general purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected to form a differentiallyconnected
More information1 of 6 03/12/2012 14:56 2012-12-03 HAMEG > Products > Accessories > Probes http://www.hameg.com/186.0.html P R O B E S H Z 5 6-2 * AC/ DC Current Clamps This AC/DC Current Probe is used to measure currents
More informationCHAPTER 3 BASIC OPERATING METHODS OF PHOTOMULTIPLIER TUBES
CHAPTER 3 BASIC OPERATING METHODS OF PHOTOMULTIPLIER TUBES This section provides the first-time photomultiplier tube users with general information on how to choose the ideal photomultiplier tube (often
More information400 MHz Photoreceiver with InGaAs PIN Photodiode
The picture shows the -FS with free space input. The photoreceiver will be delivered without post holder and post. Features InGaAs PIN detector Spectral range 900... 1700 nm Bandwidth DC... 400 MHz Amplifier
More informationCX1100 Series Current and Differential Sensors
DATA SHEET CX00 Series Current and Differential Sensors CX0A Current Sensor, Single Channel CX0A Current Sensor, Dual Channel CX03A Current Sensor, Low Side CX04A Current Sensor, Selectable Resistive Sensor
More informationLow Power, Precision FET-INPUT OPERATIONAL AMPLIFIERS
OPA3 OPA3 OPA3 OPA3 OPA3 OPA3 OPA3 OPA3 OPA3 Low Power, Precision FET-INPUT OPERATIONAL AMPLIFIERS FEATURES LOW QUIESCENT CURRENT: 3µA/amp OPA3 LOW OFFSET VOLTAGE: mv max HIGH OPEN-LOOP GAIN: db min HIGH
More informationHA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information
HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,
More information10-Bit µp-compatible D/A converter
DESCRIPTION The is a microprocessor-compatible monolithic 10-bit digital-to-analog converter subsystem. This device offers 10-bit resolution and ±0.1% accuracy and monotonicity guaranteed over full operating
More informationhvbase-n Negative High Voltage Generator and Voltage Divider for 10-stage PMT
and Voltage Divider for 10-stage PMT hvbase-n The is a combined negative high voltage generator and voltage divider for 10-stage photomultiplier tubes (PMT). It supports digital or analog high-voltage
More informationCA-550 Series / CA-650 Series
WIDEBAND CURRENT AMPLIFIER CA- SERIES / CA-6 SERIES CA- Series / CA-6 Series CA- Series and CA-6 Series are low noise wideband current amplifiers (current to voltage converter) with a high gain. There
More informationLM4562 Dual High Performance, High Fidelity Audio Operational Amplifier
Dual High Performance, High Fidelity Audio Operational Amplifier General Description The is part of the ultra-low distortion, low noise, high slew rate operational amplifier series optimized and fully
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationAN7511, AN7511S. 1-W BTL audio power amplifier. ICs for Audio Common Use. Overview. Features. Applications. Block Diagram AN7511
.±. AN, ANS -W BTL audio power amplifier Overview The AN and ANS are the audio power amplifier ICs with -ch output. The BTL (Balanced Transformer-Less) method can provide fewer external parts and more
More information8558A 8 1/2 Digit Multimeter
8558A 8 1/2 Digit Multimeter Product Specifications March 2019 Rev. A 2019 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks
More informationHA MHz, High Slew Rate, High Output Current Buffer. Description. Features. Applications. Ordering Information. Pinouts.
SEMICONDUCTOR HA-2 November 99 Features Voltage Gain...............................99 High Input Impedance.................... kω Low Output Impedance....................... Ω Very High Slew Rate....................
More informationTL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
More informationSerial Input 18-Bit Monolithic Audio DIGITAL-TO-ANALOG CONVERTER
Serial Input 8-Bit Monolithic Audio DIGITAL-TO-ANALOG CONVERTER FEATURES 8-BIT MONOLITHIC AUDIO D/A CONVERTER LOW MAX THD + N: 92dB Without External Adjust 00% PIN COMPATIBLE WITH INDUSTRY STD 6-BIT PCM56P
More informationHigh Speed FET-INPUT OPERATIONAL AMPLIFIERS
OPA OPA OPA OPA OPA OPA OPA OPA OPA High Speed FET-INPUT OPERATIONAL AMPLIFIERS FEATURES FET INPUT: I B = 5pA max WIDE BANDWIDTH: MHz HIGH SLEW RATE: V/µs LOW NOISE: nv/ Hz (khz) LOW DISTORTION:.% HIGH
More informationUltralow Input Bias Current Operational Amplifier AD549
Ultralow Input Bias Current Operational Amplifier AD59 FEATURES Ultralow input bias current 60 fa maximum (AD59L) 250 fa maximum (AD59J) Input bias current guaranteed over the common-mode voltage range
More informationINTEGRATED CIRCUITS DATA SHEET. TDA1074A Dual tandem electronic potentiometer circuit. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 December 1982 GENERAL DESCRIPTION The is a monolithic integrated circuit designed for use as volume and tone control circuit in stereo
More informationSON3130 FEATURES PRODUCT DESCRIPTION PIN CONFIGURATION (TOP VIEW) APPLICATIONS
PRODUCT DESCRIPTION The SON313 is designed for heart rate output with SON133(heart rate sensor) offering low cost. It has a wide input common mode voltage range and output voltage swing, and takes the
More informationSerial Input 18-Bit Monolithic Audio DIGITAL-TO-ANALOG CONVERTER
Serial Input 8-Bit Monolithic Audio DIGITAL-TO-ANALOG CONVERTER FEATURES 8-BIT MONOLITHIC AUDIO D/A CONVERTER LOW MAX THD + N: 92dB Without External Adjust 00% PIN COMPATIBLE WITH INDUSTRY STD 6-BIT PCM56P
More informationCurrent Transducer CTSR 1-P = 1A
Current Transducer CTSR 1-P I PRN = 1A For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary (high power) and the secondary circuit (electronic circuit).
More informationElectro Optical Components, Inc. SUNSTAR 传感与控制 TEL: FAX: Skylane Boulev
Electro Optical Components, Inc. 5460 Skylane Boulevard, Santa Rosa, CA 95403 Toll Free: 855-EOC-6300 www.eoc-inc.com info@eoc-inc.com Features Transimpedance (Gain) Switchable from 1 x 10 3 to 1 x 10
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM150/LM250 LM350 THREE-TERMINAL 3 A ADJUSTABLE VOLTAGE REGULATORS GUARANTEED
More informationINTEGRATED CIRCUITS DATA SHEET. TDA1029 Signal-sources switch. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 January 1980 The is a dual operational amplifier (connected as an impedance converter) each amplifier having 4 mutually switchable inputs
More informationLINEAR PRODUCTS. NE592 Video amplifier. Product specification April 15, Philips Semiconductors
LINEAR PRODUCTS April 5, 992 Philips Semiconductors DESCRIPTION The is a monolithic, two-stage, differential output, wideband video amplifier. It offers fixed gains of and 4 without external components
More informationMIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp
MIC915 Dual 135MHz Low-Power Op Amp General Description The MIC915 is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply
More informationVariable Gain Sub Femto Ampere Current Amplifier
Features 0.4 fa Peak-Peak Noise Very High Dynamic Range: Sub-fA to 1 ma (> 240 db) Transimpedance (Gain) Switchable from 1 x 10 4 to 1 x 10 13 V/A Bandwidth up to 400 Hz, Rise Time Down to 0.8 ms - Independent
More information200 MHz Photoreceiver with Si PIN Photodiode
The picture shows the -FS with free space input. The photoreceiver will be delivered without post holder and post. Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth
More informationHigh Speed BUFFER AMPLIFIER
High Speed BUFFER AMPLIFIER FEATURES WIDE BANDWIDTH: MHz HIGH SLEW RATE: V/µs HIGH OUTPUT CURRENT: 1mA LOW OFFSET VOLTAGE: 1.mV REPLACES HA-33 IMPROVED PERFORMANCE/PRICE: LH33, LTC11, HS APPLICATIONS OP
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD 2 X 12 W HI-FI AUDIO POWER AMPLIFIERS WITH MUTE LINEAR INTEGRATED CIRCUIT DESCRIPTION The UTC PA2616 is dual power amplifiers which the supplied in a 9-lead plastic power
More information2.5Gb/s Burst Mode Trans-impedance Amplifier with Precision Current Monitor
2.5Gb/s Burst Mode Trans-impedance Amplifier with Precision Current Monitor for XG-PON1 OLT MG3250 is a burst mode TIA with high optical sensitivity (typical 24dBm with PIN and 30dBm with APD), wide input
More informationHigh Speed, Low Power Dual Op Amp AD827
a FEATURES HIGH SPEED 50 MHz Unity Gain Stable Operation 300 V/ s Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads EXCELLENT VIDEO PERFORMANCE 0.04% Differential Gain @ 4.4 MHz 0.19 Differential
More informationFHP3350, FHP3450 Triple and Quad Voltage Feedback Amplifiers
FHP335, FHP345 Triple and Quad Voltage Feedback Amplifiers Features.dB gain flatness to 3MHz.7%/.3 differential gain/phase error 2MHz full power -3dB bandwidth at G = 2,V/μs slew rate ±55mA output current
More informationFSK DEMODULATOR / TONE DECODER
FSK DEMODULATOR / TONE DECODER GENERAL DESCRIPTION The is a monolithic phase-locked loop (PLL) system especially designed for data communications. It is particularly well suited for FSK modem applications,
More informationTEB1033 TEF1033-TEC1033
TEB1033 TEF1033-TEC1033 PRECISION DUAL OPERATIONAL AMPLIFIERS VERY LOW INPUT OFFSET VOLTAGE : 1mV max. LOW DISTORTION RATIO LOW NOISE VERY LOW SUPPLY CURRENT LOW INPUT OFFSET CURRENT LARGE COMMON-MODE
More informationLM833 Dual Audio Operational Amplifier
LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier
More informationLM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers
LM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers General Description The LM6172 is a dual high speed voltage feedback amplifier. It is unity-gain stable and provides excellent
More informationGreat Britain: LASER COMPONENTS (UK) Ltd., Phone: , Fax: , France: LASER COMPONENTS
F E M T O P H O T O R E C E I V E R O V E R V I E W 2 0 0 5 S O P H I S T I C A T E D T O O L S F O R S I G N A L R E C O V E R Y Selection Guide Photoreceivers Model Spectral Calibration Bandwidth Min.
More informationLM3046 Transistor Array
LM3046 Transistor Array General Description The LM3046 consists of five general purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected to form
More informationHigh Precision 10 V IC Reference AD581*
a FEATURES Laser Trimmed to High Accuracy: 10.000 Volts 5 mv (L and U) Trimmed Temperature Coefficient: 5 ppm/ C max, 0 C to +70 C (L) 10 ppm/ C max, 55 C to +125 C (U) Excellent Long-Term Stability: 25
More informationMODEL: 20VS2-02. Hybrid IC Isolation Amplifiers 20 Series
MODEL: 0VS-0 Hybrid IC Isolation Amplifiers 0 Series ISOLATION AMPLIFIER (-port isolation) Functions & Features Being used for printed wiring board installation High-linearity Low power consumption Isolating
More informationHigh Speed, Low Power Dual Op Amp AD827
a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential
More informationHA Features. 650ns Precision Sample and Hold Amplifier. Applications. Functional Diagram. Ordering Information. Pinout
HA-50 Data Sheet June 200 FN2858.5 650ns Precision Sample and Hold Amplifier The HA-50 is a very fast sample and hold amplifier designed primarily for use with high speed A/D converters. It utilizes the
More informationLock-In-Amplifier Module
Features BNC Connectors for Input and Output Signals Rugged Aluminium Housing Single Phase Detection with X Output Working Frequency 5 Hz... 10 khz, Digital Phase Shifter 0... 360 Parameter Control by
More informationMGM 3000X Q67000-A5179 P-DSO-20-1 (SMD) MGM 3000X Q67006-A5179 P-DSO-20-1 Tape & Reel (SMD)
Video Modulator for FM/AM-Audio MGM 3000X Bipolar IC Features FM- and AM-audio modulator Audio carrier output for suppression of harmonics Sync level clamping of video input signal Controlling of peak
More informationHigh Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
More information87415A microwave system amplifier A microwave. system amplifier A microwave system amplifier A microwave.
20 Amplifiers 83020A microwave 875A microwave 8308A microwave 8307A microwave 83006A microwave 8705C preamplifier 8705B preamplifier 83050/5A microwave The Agilent 83006/07/08/020/050/05A test s offer
More information300MHz, Low-Power, High-Output-Current, Differential Line Driver
9-; Rev ; /9 EVALUATION KIT AVAILABLE 3MHz, Low-Power, General Description The differential line driver offers high-speed performance while consuming only mw of power. Its amplifier has fully symmetrical
More informationAT431 Adjustable Precision Shunt Regulators
FEATURES DESCRIPTION Programmable Output Voltage to 40V Voltage Reference Tolerance 1.0% for B Series and 0.5% for A Series Low Dynamic Output Impedance 0.22Ω Sink Current Capability of 0.1mA to 100mA
More informationDS2000ICLA. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 0 ppm offset Current
More informationDUAL OP AMP AND VOLTAGE REFERENCE General Description. Features
General Description The is a monolithic IC specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies. The device contains two Op Amps and
More informationOBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B
a FEATURES Excellent Noise Performance: 950 pv/ Hz or 1.5 db Noise Figure Ultralow THD: < 0.01% @ G = 100 Over the Full Audio Band Wide Bandwidth: 1 MHz @ G = 100 High Slew Rate: 17 V/ s typ Unity Gain
More informationDATA SHEET. TDA7056B 5 W mono BTL audio amplifier with DC volume control INTEGRATED CIRCUITS Aug 15
INTEGRATED CIRCUITS DATA SHEET W mono BTL audio amplifier with DC Supersedes data of 1996 May 8 File under Integrated Circuits, IC1 1997 Aug 1 FEATURES DC Few external components Mute mode Thermal protection
More informationINTEGRATED CIRCUITS DATA SHEET. TDA1596 IF amplifier/demodulator for FM radio receivers. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC01 April 1991 GENERAL DESCRIPTION The provides IF amplification, symmetrical quadrature demodulation and level detection for quality home
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More informationCLC440 High Speed, Low Power, Voltage Feedback Op Amp
CLC440 High Speed, Low Power, Voltage Feedback Op Amp General Description The CLC440 is a wideband, low power, voltage feedback op amp that offers 750MHz unity-gain bandwidth, 1500V/µs slew rate, and 90mA
More informationDATA SHEET. TDA8415 TV and VTR stereo/dual sound processor with integrated filters and I 2 C-bus control INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET TV and VTR stereo/dual sound processor with integrated filters and I 2 C-bus control File under Integrated Circuits, IC02 May 1989 with integrated filters and I 2 C-bus control
More informationFeatures. Applications
105MHz Low-Power SOT23-5 Op Amp General Description The is a high-speed operational amplifier which is unity gain stable regardless of resistive and capacitive load. It provides a gain-bandwidth product
More information400 MHz Photoreceiver with Si PIN Photodiode
The picture shows the -FS. The photoreceiver will be delivered without post holder and post. Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth DC... 400 MHz Amplifier
More informationNJM2823. Precision Micropower Shunt Voltage Reference
Precision Micropower Shunt Voltage Reference GENERAL DESCRIPTION NJM2823 is a precision and low quiescent current shunt voltage reference. Reference voltage form bandgap circuit has guaranteed the high
More informationMER1 Series 1kVDC Isolated 1W Single Output DC/DC Converters
www.murata-ps.com MER1 Series SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage Output Current Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)
More informationLM138/LM238 LM338 THREE-TERMINAL 5 A ADJUSTABLE VOLTAGE REGULATORS
LM138/LM238 LM338 THREE-TERMINAL 5 A ADJUSTABLE VOLTAGE REGULATORS GUARANTEED 7A PEAK OUTPUT CURRENT GUARANTEED 5A OUTPUT CURRENT ADJUSTABLE OUTPUT DOWN TO 1.2V LINE REGULATION TYPICALLY 0.005%/V LOAD
More informationCalsytech, # 38 North Mada Street Nandambakkam, Chennai, Tamil Nadu. Discipline Electro-Technical Calibration Issue Date
Last Amended on 23.11.2016 Page 1 of 7 SOURCE 1. DC VOLTAGE $ 1mV to 10 mv 10 mv to100 mv 100 mv to1000 V 0.43% to 0.05% 0.05% to 0.01% 0.01% to 0.004% Calibrator, Calibrator by DC VOLTAGE 1mV to 20 mv
More informationHigh-Speed Photoreceiver with Si PIN Photodiode
The photoreceiver will be delivered without post holder and post Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth DC... 200 MHz Amplifier Transimpedance (Gain) 2.0
More information500mA Laser Diode Controller
IP500 500mA Laser Diode Controller Operating Manual THORLABS, Inc. Ph: (973) 579-7227 435 Route 206N Fax: (973) 300-3600 Newton, NJ 07860 USA www.thorlabs.com Table of Contents TABLE OF FIGURES 1 OVERVIEW
More information8588A Reference Multimeter
8588A Reference Multimeter Product Specifications March 2019 Rev. A 2019 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of
More informationQUAD 5V RAIL-TO-RAIL PRECISION OPERATIONAL AMPLIFIER
ADVANCED LINEAR DEVICES, INC. ALD472A/ALD472B ALD472 QUAD 5V RAILTORAIL PRECISION OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The ALD472 is a quad monolithic precision CMOS railtorail operational amplifier
More informationDUAL ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER
ADVANCED LINEAR DEVICES, INC. ALD276A/ALD276B ALD276 DUAL ULTRA MICROPOWER RAILTORAIL CMOS OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The ALD276 is a dual monolithic CMOS micropower high slewrate operational
More informationSELECTION GUIDE. Nominal Input Voltage Output Voltage. Output Current
www.murata-ps.com CRV2 Series SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage Output Current Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)
More informationModel 3102D 0-2 kv H.V. Power Supply
Features Compact single width NIM package Regulated up to ±2000 V dc. 1 ma output Noise and ripple 3 mv peak to peak Overload and short circuit protected Overload, inhibit and polarity status indicators
More informationNCM6 Series. Isolated 6W Wide Input Single & Dual Output DC/DC Converters FEATURES PRODUCT OVERVIEW
NCM Series FEATURES UL9 Reinforced Insulation ANSI/AAMI ES-, MOPP/ MOOP s recognised : Wide range voltage input Operating temperature range C to 8 C.kVDC isolation Hi Pot Test Typical efficiency to 88%
More informationPART MAX4144ESD MAX4146ESD. Typical Application Circuit. R t IN- IN+ TWISTED-PAIR-TO-COAX CABLE CONVERTER
9-47; Rev ; 9/9 EVALUATION KIT AVAILABLE General Description The / differential line receivers offer unparalleled high-speed performance. Utilizing a threeop-amp instrumentation amplifier architecture,
More informationPIN CONFIGURATIONS FEATURES APPLICATION ORDERING INFORMATION. FE, N Packages
DESCRIPTION The are monolithic sample-and-hold circuits which utilize high-voltage ion-implant JFET technology to obtain ultra-high DC accuracy with fast acquisition of signal and low droop rate. Operating
More informationFeatures. Applications SOT-23-5
135MHz, Low-Power SOT-23-5 Op Amp General Description The is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply current,
More informationHigh-Precision Voltage References with Temperature Sensor
General Description The MAX6173 MAX6177 are low-noise, high-precision voltage references. The devices feature a proprietary temperature-coefficient curvature-correction circuit and laser-trimmed thin-film
More informationPrecision 4mA to 20mA CURRENT LOOP RECEIVER
Precision ma to 0mA CURRENT LOOP RECEIVER FEATURES COMPLETE -0mA TO 0-V CONVERSION INTERNAL SENSE RESISTORS PRECISION 0V REFERENCE BUILT-IN LEVEL-SHIFTING ±0V COMMON-MODE INPUT RANGE 0.% OVERALL CONVERSION
More informationCRL2 Series. Isolated 2W Single Output DC/DC Converters FEATURES PRODUCT OVERVIEW
www.murata-ps.com CRL2 Series SELECTION GUIDE Order Code Nominal Input Voltage Output Voltage Output Current Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)
More informationTL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More informationLM4562 Dual High Performance, High Fidelity Audio Operational Amplifier
October 2007 Dual High Performance, High Fidelity Audio Operational Amplifier General Description The is part of the ultra-low distortion, low noise, high slew rate operational amplifier series optimized
More informationTL494 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power-Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
More information