XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd.

Size: px
Start display at page:

Download "XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd."

Transcription

1 XIEGU COMMUNICATION X5105 HF+50MHz Portable HF Transceiver Instruction Manual V Chongqing Xiegu Technology Co.,Ltd.

2 Important reminder: Before operating the equipment, please Security considerations: read our operating manual carefully and keep the manual, so as not to lose. Features: Do not use equipment during a lightning storm. 3.6 inch LCD screen Built in 5000mAh large capacity battery pack Built in ATU Covers all modes of HF, 50MHz band (SSB/CW/AM/FM/RTTY/PSK) IF signal output Built in AF-DSP digital noise reduction processor Equipped with trestle for desktop operation Very small in size and ultra portable Damp-proof! Don't illegal operations! Note RF high-voltage of antenna connector! Packing list: 1 Qty 1 X Power supply cable Hand microphone USB Cable Service card

3 Introduce The X5105 is an ultra-portable multimode HF transceiver. 3.6 "super large LCD display screen with rich content information. Built-in 3800mAh high-capacity battery pack can provide 6 to 8 hours of use time for outdoor use, built-in highly efficient automatic antenna tuner (ATU), so you no longer worry about the antenna problem, you can quickly deploy your field shortwave communication station. X5105 covers HF, 50MHz band full mode. X5105 has many advanced functions of large base stations. VFOA/B mode, split frequency transceiver function, RIT receive fine tuning, NB noise suppressor, AGC speed selection, NR digital noise reduction, number NOTCH, built-in automatic telegraph keys, built-in efficient automatic antenna tuner, CW trainer, large capacity battery pack, and computer-aided control functions. X5105 has a small size (about 168 * 93 * 47mm, without protrusions), light body (about 0.94kg). It provides up to 5W of RF power over the full frequency range. It operates normally from 9 to 15V DC; its low standby current provides longer battery life, it has intelligent battery management. 3

4 1 X5105 Specifications Basic Specifications Frequency range: Receive: 500kHz-30MHz 50MHz-54MHz Transmitting: 160 meters -6 meters (Amateur band only) Operating mode: A1A(CW),A3E(AM),J3E(USB/LSB),F3E(FM) minimum frequency stepping: 1Hz Antenna impedance: 50Ω Operating temperature range: -10 ~ +60 Frequency stability: after turn on the radio 1-60 minutes is + :1ppm/hour supply voltage: normal: 13.8VDC + 15%, negative grounding Operating voltage: VDC, negative grounding Current consumption: receive: 500mA@ Max transmit: 2.5A@ Max Battery capacity: Dimensions: 168*93*47mm[does not include protrusion] Weight: 0.94Kg[host only] Transmitter parameters Transmitter power:5w(ssb/cw/fm),1.5w(am Modulation mode: SSB balanced modulation/am low level amplitude modulation/fm Variable reactance frequency modulation FM Maximum frequency swing: ±5kHz spur reduction: -45dB Carrier suppression: >40dB Sideband spurious: >50dB SSB frequency response: 400Hz-2800Hz(-6dB) Microphone impedance: k(conventional 600Ω) 4

5 Receiving parameters Circuit type: double frequency conversion superheterodyne + audio DSP IF frequency: first IF: MHz second IF: MHz third IF: 455kHz(NFM) Sensitivity SSB/CW AM FM 1MHz-1.8MHz 0.35uV 10uV / 1.8MHz-28MHz 0.25uV 2uV / 28MHz-30MHz 0.25uV 2uV 0.35uV 50MHz-54MHz 0.25uV 2uV 0.35uV (PRE=on,ATT=off,NB=off,NR=off,SSB/CW/AM = 10dB S/N,FM = 12dB SINAD) Image rejection: 70dB If Rejection: 60dB Selectivity: SSB:-6dB:2.4kHz/-60dB:4.6kHz CW:-6dB:500Hz/-60dB:2000Hz AM:-6dB:6.0kHz/-60dB:25.0kHz FM:-6dB:12.0kHz/-60dB:25.0kHz Audio output: 0.6W (8Ω, 10% THD) Audio output impedance: 4 16Ω 5

6 Packing List Item X5105 Mic power cable Data cable Instructions Certificate warranty card Quantity 1pcs 1pcs 1pcs 1pcs 1pcs 1pcs 1pcs ================================================== Optional accessories Item CE-19 XPA125 Description ACC Wiring expansion card 120W PA and ATU integrated machine 6

7 Interface definition 7

8 Charging and maintenance of internal battery X5105 has a built-in 3800mAh battery pack. When the external power supply is not connected, the battery pack supplies power to the X5105, when the X5105 is connected with an external power supply, the circuit inside the machine automatically switches to the external power supply. Charging method: 1 In the menu-7, select [CHG], select CHG ON, start charging function. 2 select Charger ON, Start boot-strap charging function. 3 Select Charger OFF Shut down boot-strap charging function. If it is power off, then the default is start boot-strap charging function. 4 The external power supply voltage is set between 13.5V-15.0V and the power supply is connected to the X5105 external power supply. The host will automatically start charging. 5 The maximum charge time is about 12~15 hours. When the battery is full, the charging will stop automatically. When the battery is powered for X5105, when the battery power is about to run out, the power indication sign on the upper right corner of the screen is displayed as. At this point, the X5105 should be charged or switched to an external power supply. During the charging process, the casing of the machine has a slight fever. Normally, the lifetime of the internal battery is about 3 years. When there is a significant drop in capacity or charging failure, contact the dealer to replace the battery (outside the warranty period, you will be charged for a fee). When using an external power supply, do not exceed the rated voltage of the device, otherwise it will cause damage to the device. Please turn off the power immediately when the machine shell is very hot near the battery, and put the equipment in a safe and ventilated place. After confirming the safety situation, please contact us for proper handling. 8

9 External power supply connection External DC power supply output voltage: 13.8;electric current load capacity:3a Cable connection method: white wire connect "+", shielded wire connect "-". Shielded white EMC magnetic ring installation method:as shown; The headphone cable Loop two Loop around the magnetic ring. 9

10 2 Description of equipment 2.1 Front panel button function 1 Power button Press this button for a second to turn on or turn off the radio. 2 Mode button With this key, you can change the mode of operation and will cycle in the following mode: [LSB-USB-CW-CWR-NFM-AM] 3 PRE/ATT button With this key, the preamplifier or pre attenuator will be turned on or be turn off in the following states: [PRE=ON--ATT=ON--PRE/ATT=OFF] 4 RIT button With this key, the receive frequency adjustment function is turned on. 5 NB button With this key to turn on or turn off the NB function. 6 MENU button With this key, you can switch the current display of the multi-function menu. 7-10Multifunctional menu button Press these four buttons to turn on or off the corresponding function displayed on the menu area on the current screen. 11 Major tuning knob The main tuning knob of X5105, can be used either for frequency regulation or set the parameters. 12 ATU button 10

11 When the key is pressed for a short time, the automatic antenna tuner will be connected to the antenna port, by pressing this button for a long time, the automatic antenna tuner will be started. 13 Po button With this key, and with the main tuning knob, the power of the transmitter can be adjusted. The range of adjustment is from 0.5W-5W, stepping for 0.5W. 14 A/B button With this key, you will switch between VFOA/VFOB. 15 < button With this key, the current frequency step carries one bit to the left. 16 > button With this key, the current frequency step carries one bit to the right. 17 V/M button With this key, you can switch between VFO mode and MEMO mode. 18 Up button With this key, X5105 can be switched to higher frequency bands. 19 DN button With this key, X5105 can be switched to lower frequency bands. 20 -button With this key, you can reduce current volume. 21 +button With this key, you can increase current volume. 22 PTT button Press and hold this button, X5105 will go into the transmit state. 23 LOCK button If you press this button for a short time, you will lock all buttons and knobs on the panel; By pressing this button for a long time, you can set the backlight on / off. Status indicator A [T/R] B [DATA] C [LINK] Transmit/Receive switch indication Data indication Peripheral indicator light Indicator color description: A T/R indicator When the X5105 is in receiving mode, the indicator light is green. When the X5105 is in transmitting mode, the indicator light is red. 11

12 B DATA indicator When the data signal or channel are busy, the indicator light flashes. C LINK indicator When the host is connected with the external equipment, the indicator light will shine. Function menu corresponding to 4 multi-function buttons below screen A=B SPL NR NTH Copy VFOA to the background Split On/Off Digital noise reduction number Notch AGC FIL SRM SWR Automatic gain control selection Filter selection Scan receiving mode SWR scanning M > V MW MC TAG Save the VFO frequency on the channel Store current channel Clear current channel Channel information / custom characters(press this button for a long time to enter the editor) BK KEY KSP - CW insert function on / off Key manual / automatic mode selection Automatic key rate selection - 12

13 5. RE1 RE2 RE3 CSN Set CW message 1(Press this button for a long time to enter the message editing) Set CW message 2(Press this button for a long time to enter the message editing) Set CW message 3(Press this button for a long time to enter the message editing) Power on display call sign editing(press this button for a long time to enter the editor) SQL CMP MTR VLT Squelch function Speech compression Display switch of multi-function table Power / voltage display switching CHG MSL IFO VER Charging switch Built-in / external MIC selection IF output switch Firmware version display 8 MDN -CAR -AFC Digital MODEM Carrier Tracking (MDN=ON) frequency tracking (MDN=ON) 9 AFF -HPF -LPF SPK Digital audio filter high-pass filter lower-pass filter Speaker / headphone mode selection Screen display information 13

14 2.2 Left panel interface function 1 Left bracket Rotate the bracket when using it, when after using it, take it back to the side shield. 2 Antenna interface Connect the antenna to the 50 ohm coaxial cable with the BNC connector. 3 IF signal output port The first IF signal is output for use by the XDT1. * XDT1 is a data terminal equipment of Xiegu. 4 External speaker / earphone interface This interface is 3.5mm stereo socket (3 line), it can connect external speaker (impedance 4-16). Before inserting the headset into the interface, be sure to select earphone mode first so as to avoid damage to your hearing and headset. 5 DC power interface The external DC power input interface, it uses the standard power cord to connect the external stable DC power to this interface. The external DC power supply must be able to provide the power output of the 13.8V@3A. The interface can also be used to charge for internal battery. 2.3 Right panel interface function 14

15 1 ACC interface The interface is a 8PIN micro DIN interface, it can be used for external power amplifier connection, PTT control, band signal transmission, it can also be used to communicate with the computer for PSK communication when the audio signal input / output. 2 KEY interface The interface is 3.5mm stereo interface, which can be used to connect manual / automatic telegraph keys. Key connection is shown in this figure: Manual key, you need to "drop" And "click" connected together 3 ATU interface The interface is a 3.5mm interface (3 lines) that can be used to control external power amplifiers with antenna tuning. 4 CIV interface The interface is a 3.5mm interface (3 wire) which used for the connection of the computer aided control system or firmware update. 5 Right bracket Rotate the bracket when using it, when after using it, take it back to the side shield. 6 MIC (microphone) interface The interface can be used for microphone connections. 2.4 Handheld microphone function 15

16 1. LOCK button, you can lock the host button and the mouse button via this button, and press it again to unlock. 2. PTT button, transmitting control button. 3. Move up/down, Increase and decrease of frequency. 4. Receiving / Transmitting indicator light, microphone operated indicator light. 5. Digital key 6. FIL button, built in filter selection. 7. MODE button, selection of host operating mode. 8. Function indicator lamp, No indication. 9. Function button, F1/F2 custom settings button. 10. MW button, store operation. 11. V/M button, frequency / channel switching. 12. XFC button, No function. 13. CALL button, press this button for a long time to start the automatic antenna tuning in the host. 3 Operation 3.1 Turn on / off transceiver 1. Turn on the transceiver: just press for a long time 2. Turn off the transceiver: in the boot state, press the key for a long time. Press the button of the switch to delay one second, in order to prevent the misoperation of the switch key. Forced reset: When the host system is in a halted state, such as the key is not responding, or can not exit the transmit state and the key is not responding, long press the power button and hold for more than 8 seconds, will force reset the MCU and shut down. 3.2 Battery / voltage display 1. When the battery is powered by the built-in battery, the remaining battery power of the current battery will be displayed in the upper right corner of the display. 2. When using an external power supply, after switching to the [VLT] Page 6 menu, this location shows the voltage level of the external DC power currently connected to the transceiver. 16

17 If you have not used the X5105 transceiver for more than 20 days, we recommend that you plug it in with an external power source and charge the device until the display is done. For details, please refer to [Charge] section. 3.3 Operating frequency band selection The frequency range of X5105 covers 1~54MHz. The amateur frequencies in this range are divided into multiple frequency bands and can be switched in a number of different ways. You can complete the equipment operation according to the operation instructions in this section. press DN or UP key to switch to the next or last operation band respectively. 1.8MHz 3.5MHz 5.2MHz 7.0MHz 10MHz 14MHz 50MHz 28MHz 24MHz 21MHz 18MHz A. The opening of the 5MHz frequency band is based on the regulations of the country (or region) where it is located. B. Different versions of the machine have different frequency divisions, depending on their country (or region) regulations. C. VFO-A and VFO-B are two separate VFO modes, which can be set to different working conditions, please refer to the [VFO settings]. 3.4 Work mode selection Press the [MODE] button to switch between all modes in a fixed order. LSB USB CW CWR FM AM *VFO-A and VFO-B can be set to different operating modes in the same frequency band, thus realizing the different operation modes of "voice /CW". 17

18 3.5 Adjust the volume Adjust the output volume according to the volume plus and minus buttons. When using the AF- IN/OUT port of the ACC interface, please adjusting the volume level in the system menu. 3.6 Regulated transmit power Press the [Po] transmit power setting button, you can set the transmit power. A. Press the [Po] button to enter the power setting state, the screen will display the Po power setting number. B. Rotate the big knob, set the power, step 0.5W. When you do not understand the current state of the antenna, minimize the set transmit power value for the first time you use the X5105 transceiver. 3.7 Use the host PTT button X5105 comes with a PTT button, you can start the transceiver's transmission through this button. A. Press this button to start the transmitting function. B. Speaking into the built-in MIC hole, can be completed communications. 18

19 3.8 Set operating frequency There are two ways to set the X5105 operating frequency, use the big knob to set the frequency, or use the multi-function mic to set the frequency. A. Use large knob to set frequency Press the button [<] or [>], move the cursor of the frequency bit to the left or to the right, select the frequency of the desired step. Rotating frequency knob sets the frequency of the current step. B. Use a multi-function microphone for frequency setting Press the [F-INP ENT] button on the cursor, and the X5105 enters the frequency setting. The cursor appears on the left of the frequency display bit. Enter the desired frequency value in turn, and then press [F-INP ENT] button again to complete the frequency setting. For example, set the current frequency to MHz, and press the order as follows: First, press the [F-INP ENT] button. Please press the numeric key in turn. Once again press the [F-INP ENT] button to complete the settings. 3.9 Start the ATU (automatic antenna tuner) into the tuning function X5105 transceiver built-in an efficient automatic antenna tuner, which can help you easily complete the erection and debugging of the antenna. Press the [ATU] button shortly to access the built-in tuner and the "TUNE" logo appears on the top of the screen. Press the [ATU] button for a long time, it will start the ATU auto tuning function. When the tuning is complete, the host will automatically return to the receiving state. In actual operation, if the [HI-SWR] icon flashes on the screen, the tuning fails, and the SWR is large and needs to be tuned again RIT (receive frequency trimming) Relative to the set frequency, the RIT function can set the offset value of the actual 19

20 receiving frequency of the maximum ±1.5kHz. A. Press [RIT] button to start RIT function. B. The rotating knob can change the receiver frequency in the range of ±5kHz. The screen has the corresponding area to display the frequency change value. C. If you want to clear the RIT offset, press [RIT] button for about 2 seconds, in the system prompt tone "beep" sound, the value of RIT settings will be cleared. If the frequency offset range more you want, you can use split frequency transceiver mode. Please refer to the VFO instructions for details Automatic gain control (AGC) By adjusting the appropriate AGC automatic gain control speed, the receiver can achieve the best effect. A. Switch to the second page menu, press [AGC] function button shortly. B. The AGC function will be selected in the following order: AGC- FAST AGC- OFF AGC- SLOW AGC- AUTO When you select "AGC-AUTO", the CW mode is actually "AGC-FAST", in voice mode is "AGC-SLOW." If AGC-OFF is selected, the AGC system is turned off and the display of the S table is stopped Preamplifier / preamplifier (PRE/ATT) Pre amplifier (PRE) and pre attenuator (ATT) can improve the receiver's listening effect. When the signal is weak, the preamplifier can be switched on to increase the signal strength. When the signal is strong, the preamplifier can be switched on to reduce the signal strength. Of course, you can also choose to turn off the circuit unit so that the signal will by pass. A. Press the [PRE/ATT] button to start the function. B. The switching sequence will follow the following loop: PRE ATT OFF In the low frequency waves (less than 10MHz) operation, the preamplifier can be closed, then let signal in by-pass state, it will be more conducive to improve the receiving effect, 20

21 And it can avoid the blocking of receiver caused by strong interference signal. Typically, when the S table is still changing, the preamplifier is not need to turned on Noise suppressor NB Noise suppressor can effectively eliminate some specific pulse type interference, especially the noise produced by the automobile ignition system, and can improve the receiving effect obviously. A. Press the [NB] button, the screen appears corresponding prompt information, NB function is turned on. B. Press the [NB] button again, it will turn off the NB noise suppressor. * The NB function can only suppress the pulse noise of a specific type, and can not replace the NR noise reduction function The Short-wave Data MODEM (MDN)(Currently only PSK31 receive decoding function can be used.) X5105 built-in amateur radio data communications modem. A. In the menu-7--modem function selection; select [MDN], Open the data function; B. [CAR] is the carrier tracking mode; C. [AFC] frequency tracking mode; When receiving the PSK31 signal, the spectrogram will display the spectrum of the corresponding signal, and the modulation information of PSK31 mode will be automatically demodulated. D. Press [MDN] again, then Exit Pilot frequency operation SPL and VFOA/B setting There are two independent VFO in X5105 transceiver, which can set different frequencies and modes respectively. Set the VFO reasonably, and with the menu SPL function, you can easily achieve pilot frequency transceiver operation mode. VFO settings: A. Press the [A/B] button, you can switch between VFO-A and VFO-B. B. When you switch to a certain VFO state, you can set the current VFO's working frequency, working mode, and so on. Pilot frequency transceiver operation method: A. First set the receiver frequency and mode (VFO-A). B. And then set the transmit frequency and mode (VFO-B). 21

22 C. Press [MENU] button, switch to the first page menu, select the SPL function, it opens the pilot frequency transceiver working mode. *You can also make full use of VFOA/B to set different frequencies or modes, so double frequency monitoring can be achieved via real-time switching VFO mode /MEMO mode (V/M) setting Transceiver can switch between VFO mode and MEMO mode, and realize flexible operation mode. A. Press the [V/M] button, you can switch between the VFO (frequency) mode and the MEMO (frequency) mode. B. In the current mode, press the [V/M] button, and then switch to another mode Lock button /Backlight off operation The lock key (LOCK) can avoid the incorrect triggering of the transceiver and the microphone during outdoor operation. A. Press the [Lock] button shortly to start the lock. B. Press the [Lock] button shortly again to turn off the lock. C. After locking, the corresponding area on the screen will have a locked symbol display. D. Press the [LOCK] button for a long time to turn off the display backlight completely. Press and hold the button again, turn on the backlight. This function is still valid when the lock is on. 22

23 3.18 CW communication Operate with a hand key or an external keying device. A. Insert the plug of the key (three wire) into the KEY interface on the right. B. Press the [MODE] button and switch mode to CW (or CWR). C. Press the [MENU] button for a long time, rotate the knob, transfer Menu #2(CW T/Rx Delay Time), press the button [<] and [>] set the delay time (default: 500ms). Press the corresponding [YES] button at the bottom of the screen to save the new setting and exit the menu mode. D. Press the [MENU] button, switch to the fourth page menu, select the BK function. E. Press the key, you can do the CW communication. *Practice mode You can use X5105 as a CW code trainer, as follows: Press the [MENU] button briefly, switch to the fourth page menu, select the BK function as "OFF". In this state, press the key, the transceiver CW side tone issued, but did not transmit the signal. F. The volume of the CW side tone can be adjusted by system menu, as follows: Press [MENU] button for a long time to enter menu mode. Turn to menu fifteenth (BEEP Volum); Rotary encoder, select the required volume level, range from 0~7 adjustable; After completing the operation, press the corresponding [YES] key below the screen, save the new settings and exit the menu mode. G. The tone of the CW side tone can be adjusted by the third system menu (CW RX Side Tone), as follows: Press [MENU] button for a long time to enter menu mode. Move to Menu 3 (CW RX Side Tone) Press the button [<] and [>] with the rotary encoder, select the required tone, range from 500~1200Hz to adjustable, the default value is 800Hz. After completing the operation, press the corresponding [YES] key below the screen, save the new settings and exit the menu mode. H. The left and right hand patterns in CW mode can be adjusted by [KEY] on the fourth page menu, as follows: Press the [MENU] button shortly and switch to the fourth page menu. 23

24 Press [KEY] button, select Manual / left hand / right hand mode. I. The automatic key rate adjustment method is as follows. Press the [MENU] button shortly and switch to the fourth page menu. Press the [KSP] button, rotate the encoder to adjust the automatic key rate CW automatic calling device The X5105 host provides 3 sets of CW preset message storage to realize automatic call in CW mode. Quickly press the [MENU] button, switch to the fifth page menu. Press [RE1] ~ [RE3] function button 2 seconds, into the preset message editor. In the text editor window, under the screen to provide the text editing tools used, press the corresponding function button to enable the corresponding function. After editing, press the [SAVE] button to save the edited message content and return to the normal operation state. Quickly press [RE1] ~ [RE3] function button, you can start the CW automatic call SWR scanner The X5105 host has the function of a simple antenna analyzer, which can scan the SWR parameters of the current antenna and facilitate the user to adjust the antenna. Press [MENU] button shortly, switch to the second page menu. Press the [SWR] function button, start SWR scanning function. Under the scanner interface, the SWR of the current antenna can be observed intuitively. Press the [BW] function button, you can set the SWR scanning bandwidth. Press the [QUIT] function button, exit SWR scanner. The scanning results of the SWR scanner may have some errors, such as the accurate measurement of antenna SWR and other data, please use professional antenna analyzer or RF network analyzer for measurement Digital audio filter(aff) A. Light press[menu] to Page 9; B. Select [AFF], open the digital filter function. In this case, [HPF] and [LPF] function options are displayed. C. [HPF] is a high-pass filter option, and [LPF] is a low-pass filter option. Select any filter, rotate the main knob to adjust the filter parameters. Two sets of filters cooperate, can form the ultra-narrow band filter, can improve the signal performance. D. Press [AFF] again, Exit. 1. SSB mode: We recommend to adjust the minimum HPF to 300Hz, the LPF adjust to 1800 ~ 2200Hz. 24

25 2. CW mode: We recommend to adjust the minimum HPF to 500Hz,the LPF adjust to 900 ~ 1200Hz Speaker / headphone mode switch A. Light press[menu] to Page 9; B. Select [SPK], Switch between speaker / headphone mode. At this point, the left side of the screen will display the corresponding speaker icon or headset icon. When in speaker mode, do not insert headphones. Otherwise it will damage your hearing and headphone equipment Frequency / channel scan SCN No function Channel storage(mw) Regular channel storage: A. In VFO mode, parameters such as frequency, mode and advanced functional status are adjusted. B. Press the [MENU] button briefly, switch to the third page menu, select the [MW] function, start channel storage operation. C. Rotate the encoder to select the channel number to be stored. Press the [YES] button shortly to complete the channel storage. D. If the current channel has stored the information and used this channel number to store again, the previous channel information is cleared and the current channel information is saved. Adjust storage channel: A. If in VFO mode, press the [V/M] button on the panel, it will enter the channel mode. B. Rotate the encoder to switch the current channel. Clear channel storage: A. In the channel mode, press the [MENU] button, switch to the third page menu, press the MC function key, start clear channel function. B. At this point, the channel number starts flashing. Rotating encoder to the corresponding channel number, press [YES] button shortly, you can complete the channel removal Channel naming The stored channels can be named with the labels of letters and numbers. A. Bring up the channel you want to name. B. Press the [MENU] button shortly, switch to the third page menu, press the [TAG] button for 2 seconds, and then release it into the text editor. C. In the text editor, under the screen to provide text editing tools used, press the corresponding function button to enable the corresponding function. D. After editing, press the [SAVE] button to save the set text content and return to the normal operation state. 25

26 E. In the channel mode, press the [TAG] button shortly, you can switch between the channel number /user-defined channel name Boot interface call sign setting This machine can set up the call sign information displayed on the boot interface, as follows: Press [MENU] button shortly, switch to page 5 menu, select [CSN] function, enter the call sign editor. In the editor, the bottom of the screen to provide text editing tools used, press the corresponding function button to enable corresponding function. After editing, press the [SAVE] button to save the set text and return to normal operation. When you start the machine again, the boot screen will display your edited text message. 4. System menu operation The System Settings menu allows you to personalize the transceiver to better suit your usage habits. Press the [MENU] key for 1 second and enter the system settings menu; Press the [<] and [>] key buttons below the screen to bring up the menu items you want to set. Press the [<] and [>] button on the board below and rotate the encoder to set the number you want. After setting, press the [YES] button to save the current settings and exit the menu mode. *In the fourth step, if the [NO] button is pressed shortly, the new settings will not be saved and the system menu mode will be exited. System menu specification Menu item Functional description Set value Default value 01 RF GAIN Receive RF gain 0~100% 65% 02 CW T/Rx Delay Time CW transmit delay 0~5000ms 200ms 03 CW RX Side Tone CW receiving side tone 50~1200Hz 800Hz 04 Tx AF Gain SSB MIC gain in SSB mode 0~100% 05 Tx AF Gain AM MIC gain in AM mode 0~100% 50% 06 Tx AF Gain NFM MIC gain in NFM mode 0~100% 100% 07 RX AF Gain SSB 08 RX AF Gain AM SSB mode receiving audio gain 10~100% 40% AM mode receiving audio gain 10~100% 90% 26

27 09 RX AF Gain NFM LCD Backlight 10 Level NFM mode receiving audio gain 10~100% 90% Screen backlight adjustment 0~100% 80% 11 Ref Clock System reference clock Hz Don t adjustment! 12 NFM TX IF NFM mode transmit IF Hz 13 Outband TX 14 Misc Option Amateur band transmit Don t adjustment! control Disable / Enable Disable Digital baseband configuration 0x7A5C3360 / 0x59A Beep Volum system volume 1~ AUX AFIN Volum ACC port input volume 0~ AUX AFOUT 18 User Key F1 19 User Key F2 Volum ACC port output volume 0~31 3 Manual F1 button customize / TS- Manual F2 button customize / TS- 20 Ext MIC Bias External MIC bias setting Disable / Enable Enable 21 Reset ALL Reset all system parameters No / YES No * The default parameter ensures that the transceiver operates in a better state. You can also set up the transceiver according to your own habits. 5 Restore factory settings: When the system parameter setting error causes the host unable to work, you can reset the transceiver using the "restore factory" function, and then all the data set on the transceiver will be cleared. Select [Reset ALL] menu, adjust to "YES", and press the [YES] button below the screen. 6 Connection and operation with computer aided control system 6.1 PSK communications and wiring instructions X5105 transceiver can be connected with the computer, using the corresponding computer software to complete the PSK communication. A. From the ACC port (MINI-DIN8), the computer audio output / input is connected to X5105. B. Use the data cable to connect the CIV port of the X5105 with the computer and ensure the driver is installed correctly. The PC software can control the X5105 transceiver. 27

28 C. Adjust the volume of X5105, ACC port input / output volume to the right, observe the software interface, to avoid the audio amplitude is too large can not communicate. * In order to prevent interference, the radio and computer must be grounded well. Please install EMC magnetic ring for the data line and audio line, and install it as close as possible to the host of the radio. The X5105 uses the standard CIV instruction set. You can use it to remotely control the transceiver, you can also control the X Band data format The ACC port of the X5105 provides band data for each band. The band data can be used to control the peripheral, to make automatic band switching, or to identify the band information for other devices. Band Voltage Band Voltage Band Voltage Band Voltage 1.8MHz 230mV 7MHz 920mV 18MHz 1610mV 28MHz 2300mV 3.5MHz 460mV 10MHz 1150mV 21MHz 1840mV 50MHz 2530mV 5.0MHz 690mV 14MHz 1380mV 24MHz 2070mV / After-sales service policy 1. Warranty: This product has two years warranty effective from the date of purchase. This warranty covers only manufacturing- and parts defects. It does not cover damage caused by lightning, excess voltage on the power supply, accidental damage or purposeful damage or misuse. If the product needs warranty repair within two weeks of receiving the product, XieGu will pay for the shipping both ways. After two weeks XieGu will pay only for return shipping. If the product is not covered under warranty, the customer pays for shipping both ways plus the cost of the repair. 2. Warranty limitations: Any of the following will void the warranty applicable to the product and its accessories: A. Modification-, removal-, or maintenance of the internal circuitry, without permission and authorization; B. Unauthorized change of product s embedded software; 28

29 C. Immersion in liquid or signs of external damage; D. Warranty period expired; E. Product s serial number is missing, torn or blurred so we cannot determine if the radio is under warranty; F. Product was not bought from XieGu or authorized distributor of XieGu. *None of the following conditions, are covered by the warranty: A. Damage caused by improper use by the user; B. Damage caused by an accident; C. Damage due to incorrect testing, maintenance, debugging, or other changes; D. Damage is not caused by the material or the quality of production; E. Damage to the shell or other external components due to improper use. Contact us: service@cqxiegu.com 29

30 Xiegu communication 30

XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd.

XIEGU COMMUNICATION X5105. HF+50MHz Portable HF Transceiver. Instruction Manual. Chongqing Xiegu Technology Co.,Ltd. XIEGU COMMUNICATION X5105 HF+50MHz Portable HF Transceiver Instruction Manual Chongqing Xiegu Technology Co.,Ltd. www.cqxiegu.com Important reminder: Before operating the equipment, please Security considerations:

More information

X108G. Outdoor version Operating Manual

X108G. Outdoor version Operating Manual XIEGU HF TRANSCEIVER X108G Outdoor version Operating Manual Chongqing XieGu Technology Co.,Ltd 403,4th buildings,youth DreamWorks, No.87, Langkou industrial park, Langkou community, Dalang Avenue,new district

More information

HF TRANSCEIVER V1.0. Copyright 2014, XIEGU, Inc. All Rights Reserved

HF TRANSCEIVER V1.0. Copyright 2014, XIEGU, Inc. All Rights Reserved HF TRANSCEIVER V1.0 Copyright 2014, XIEGU, Inc. All Rights Reserved Table of Contents I. Introduction equipment Second, the device description Third, the operating instructions Four, advanced menu settings

More information

HFTRANSCEIVER X108G. Operating Manual XIEGU TECH V1.01A. Outdoor Version. Revise: Copyright 2016, XIEGU, Inc.

HFTRANSCEIVER X108G. Operating Manual XIEGU TECH V1.01A. Outdoor Version. Revise: Copyright 2016, XIEGU, Inc. HFTRANSCEIVER X108G Operating Manual XIEGU TECH V1.01A Outdoor Version Revise: 2016-1 Copyright 2016, XIEGU, Inc. 1 All Rights Reserved Important reminder: Before operating the equipment, please read Security

More information

HFTRANSCEIVER X108G. OperatingManual XIEGUTECH V1.01A. OutdoorEdition. Revise: Copyright 2015, XIEGU, Inc.

HFTRANSCEIVER X108G. OperatingManual XIEGUTECH V1.01A. OutdoorEdition. Revise: Copyright 2015, XIEGU, Inc. HFTRANSCEIVER X108G OperatingManual XIEGUTECH V1.01A OutdoorEdition Revise: 2015 Copyright 2015, XIEGU, Inc. 1 All Rights Reserved Important reminder: Before operating the equipment, please read Security

More information

LnR Precision, Inc. 107 East Central Avenue, Asheboro, NC

LnR Precision, Inc. 107 East Central Avenue, Asheboro, NC LD5 CW/SSB QRP Transceiver Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase suppression

More information

LD5 CW/SSB QRP Transceiver SDR /DSP

LD5 CW/SSB QRP Transceiver SDR /DSP LD5 CW/SSB QRP Transceiver SDR /DSP Quick guide manual Description: At the development base of the digital signal processing unit, an algorithm is embedded for IQ processing of the channels with phase

More information

SPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver

SPECS FEATURES SUPPLIED ACCESSORIES. HF All Band Transceiver 718 HF All Band Transceiver RX 0.030-29.999999MHz* TX 1.800-1.999999 MHz** 3.500-3.999999 MHz** 7.000-7.300000 MHz 10.100-10.150000 MHz 14.000-14.350000 MHz 18.068-18.168000 MHz 21.000-21.450000 MHz 24.890-24.990000

More information

SUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups

SUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups SUBELEMENT T4 Amateur radio practices and station set up 2 Exam Questions - 2 Groups 1 T4A Station setup: connecting microphones; reducing unwanted emissions; power source; connecting a computer; RF grounding;

More information

TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_

TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_ New Product Release Information Oct 2014 TS-590SG HF/ 50MHz All-Mode TRANSCEIVER_ Kenwood introduces Updated to new G version new HF/50MHz All-Mode Transceiver Four years ago we launched our best-selling

More information

Elmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial)

Elmer Session Hand Out for 3/3/11 de W6WTI. Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) Elmer Session Hand Out for 3/3/11 de W6WTI Some Common Controls Found On Amateur Radio Transceivers. (From ARRL web site tutorial) The placement of the controls may vary from manufacturer to manufacturer

More information

The Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links

The Icom IC Adam Farson VA7OJ. A New Top-class HF/6m Transceiver. IC-7700 Information & Links The Icom IC-7700 A New Top-class HF/6m Transceiver Adam Farson VA7OJ IC-7700 Information & Links Copyright 2008 North Shore Amateur Radio Club NSARC HF Operators IC-7700 1 IC-7700 front panel This is a

More information

Icom IC-9100 HF/VHF/UHF transceiver

Icom IC-9100 HF/VHF/UHF transceiver 263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Icom IC-9100 HF/VHF/UHF

More information

I.D.A. Operation manual

I.D.A. Operation manual TRX-200 Wide ide Band Receiver Operation manual Thank you for purchasing the TRX-200 all modes wide band monitoring receiver. Please read this operating manual carefully to avoid miss operation of the

More information

Frequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor

Frequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency

More information

WORLD BAND RADIO. AM/FM/SW/L W/AIR Band /SSB radio with LCD backlight OWNER S MANUAL

WORLD BAND RADIO. AM/FM/SW/L W/AIR Band /SSB radio with LCD backlight OWNER S MANUAL WORLD BAND RADIO AM/FM/SW/L W/AIR Band /SSB radio with LCD backlight display and keypad direct entry OWNER S MANUAL WARNING Do not expose this appliance to rain or moisture Do not submerge or expose to

More information

Technician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers

Technician License Course Chapter 5. Lesson Plan Module 11 Transmitters, Receivers and Transceivers Technician License Course Chapter 5 Lesson Plan Module 11 Transmitters, Receivers and Transceivers Generalized Transceiver Categories Mobile Single Band Dual Band All Band Multimode Handheld (HT) VHF/UHF

More information

GRAND STRAND AMATEUR RADIO CLUB

GRAND STRAND AMATEUR RADIO CLUB The GRAND STRAND AMATEUR RADIO CLUB (GSARC) Myrtle Beach SC is offering used amateur related equipment for sale. Written bids may be submitted to the GSARC up to Friday, November 23 rd, 2018. Only currently

More information

DX AM FM SSB CW PA Amateur Base Station Transceiver OWNER S MANUAL RX / TX 2 4 POWER NF CHANNEL MODE RF POWER OFF CAL OFF OFF CALIBRATE

DX AM FM SSB CW PA Amateur Base Station Transceiver OWNER S MANUAL RX / TX 2 4 POWER NF CHANNEL MODE RF POWER OFF CAL OFF OFF CALIBRATE 1 2 3 6 4050 ULA 6070 TI 80 90 100 9 DX 2517 2517 RX / TX 0 2 4 SWR WATTS SET 81012 22 1 010 3 2030 5 MOD 7 ON dbover 9 SIGNAL +20 +40+60 PA FM AM USB LSB CW POWER ON SWR NB / ANL R.BEEP +10KHz NF CHANNEL

More information

HR MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL. Content of the packaging

HR MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL. Content of the packaging HR-2800 28 MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL NOTICE! It is recommended to carefully read this owner s manual before using the product. This will also help to prevent illegal use of

More information

G11 I N S T R U C T I O N G U I D E. Midland PMR446 Transceiver

G11 I N S T R U C T I O N G U I D E. Midland PMR446 Transceiver PMR446 Transceiver G11 I N S T R U C T I O N G U I D E Midland PMR446 Transceiver MIDLAND G11 PMR446 Transceiver Thanks for choosing Midland! G11 is a portable transceiver that is free use in almost all

More information

Content. Maintenance. Features ENGLISH. 1 transceiver 1 antenna 1 battery pack 1 belt clip 1 fast desktop charger User manual

Content. Maintenance. Features ENGLISH. 1 transceiver 1 antenna 1 battery pack 1 belt clip 1 fast desktop charger User manual ENGLISH Content 1 transceiver 1 antenna 1 battery pack 1 belt clip 1 fast desktop charger User manual If any items are missing, contact your dealer. Maintenance Your Two Way Radio is an electronic product

More information

The amazing evolution of the 706 series

The amazing evolution of the 706 series The amazing evolution of the 706 series The IC-706MKIIG carries on the 706 series tradition of base station performance and features in a mobile reg-sized package. Building on this legacy, frequency coverage

More information

QUICK REFERENCE GUIDE

QUICK REFERENCE GUIDE QUICK REFERENCE GUIDE Installation 1. Install a ground system for DC noise suppression and RFI suppression 2. Install your DC power supply 3. Install lightning protection. This will help protect more than

More information

RCI-6300F25/150. Owner's Manual. AM/FM Amateur Transceiver With Built-in Frequency Counter. Table of Contents. Downloaded from

RCI-6300F25/150. Owner's Manual. AM/FM Amateur Transceiver With Built-in Frequency Counter. Table of Contents. Downloaded from Table of Contents RCI-6300F25/150 AM/FM Amateur Transceiver With Built-in Frequency Counter PAGE Chapter 1 Specifications...... 2 Chapter 2 Installation...... 3 Installing the Radio... 3 Ignition Noise

More information

DC Instruction Manual. Professional FM Transceiver

DC Instruction Manual. Professional FM Transceiver DC-1074 Professional FM Transceiver Instruction Manual Use of the citizen band radio service is licensed in Australia by ACMA Radiocommunications (Citizen Band Radio Stations) Class Licence and in New

More information

CON NEX HP. OWNER'S MANUAL Full Channel AM/FM Amateur Mobile Transceiver TABLE OF CONTENTS TUNING THE ANTENNA FOR OPTIMUM S.W.R..

CON NEX HP. OWNER'S MANUAL Full Channel AM/FM Amateur Mobile Transceiver TABLE OF CONTENTS TUNING THE ANTENNA FOR OPTIMUM S.W.R.. TABLE OF CONTENTS PAGE SPECIFICATIONS... 2 INSTALLATION... 3 LOCATION... 3 CON NEX - 4300HP MOUNTING THE RADIO... 3 IGNITION NOISE INTERFERENCE... 4 ANTENNA... 4 TUNING THE ANTENNA FOR OPTIMUM S.W.R..

More information

FT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment

FT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment FT-897 Local Oscillator Adjustment Reference Frequency Adjustment a. Connect a frequency counter to TP1032. b. Adjust the trimmer capacitor (TC5001) for 67.875000MHz ±5Hz on the frequency counter. c. Connect

More information

ALAN 777 PMR 446 Radio Set User manual

ALAN 777 PMR 446 Radio Set User manual ALAN 777 PMR 446 Radio Set User manual The all new ALAN 777 represents the very latest and most advanced technology currently available on the PMR446 and LPD market. With its stylish lines and modern design,

More information

INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h

INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER. i910h INSTRUCTION MANUAL VHF/UHF ALL MODE TRANSCEIVER i910h IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. This

More information

INSTALLATION AND CONNECTIONS

INSTALLATION AND CONNECTIONS INSTALLATION AND CONNECTIONS 3 Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer. Keep the shipping cartons. For a description and a diagram of accessory equipment

More information

User Manual. Specifications...3. Control and Operation Microphone...8. Installation...9. Installation of Main Unit...9

User Manual. Specifications...3. Control and Operation Microphone...8. Installation...9. Installation of Main Unit...9 Contents Specifications...3 Control and Operation...4-7 Microphone...8 Installation...9 Installation of Main Unit...9 Antenna Installation...9 Operational test...9 Frequency Bands Table...10 Frequency

More information

Youkits SK-1A 40m SSB/CW QRP Transceiver. Operating manual

Youkits SK-1A 40m SSB/CW QRP Transceiver. Operating manual Youkits SK-1A 40m SSB/CW QRP Transceiver Operating manual Specifications Size: 88*38*124mm (not including knob, etc.) Weight: about 280g (not including battery pack) Supply voltage: 10-15VDC Current drain

More information

D-808. FM Stereo/LW/MW/SW-SSB AIR RDS Synthesized Receiver

D-808. FM Stereo/LW/MW/SW-SSB AIR RDS Synthesized Receiver XHDATA D-808 FM Stereo/LW/MW/SW-SSB AIR RDS Synthesized Receiver WARNING Do not expose this appliance to rain or moisture Do not submerge or expose to water Protect from high humidity and rain Only operate

More information

REDSUN PF2100 PLL RADIO OPERATING MANUAL

REDSUN PF2100 PLL RADIO OPERATING MANUAL REDSUN PF2100 PLL RADIO OPERATING MANUAL TRANSLATED BY LIYPN ALL RIGHTS RESERVED JUNE 2006 (We are the copyright holder of this manual in English. Please do NOT distribute this manual in any form nor post

More information

INSTALLATION AND CONNECTIONS Section 2

INSTALLATION AND CONNECTIONS Section 2 STLLTION ND CONNECTIONS Section Unpacking - ntenna jumper cable connection - Selecting a location - Rack mounting handle attachment - Grounding -3 ntenna connection -3 CF (Compact Flash) memory card -3

More information

ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012

ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012 ELECRAFT KX3 EXTENDED VFO TEMPERATURE COMPENSATION PROCEDURE Copyright 2012 Elecraft LLC Rev. A9, November 14, 2012 Introduction The KX3 standard VFO temperature compensation is entirely adequate for most

More information

Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3

Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3 Ten-Tec Orion/Orion II Users Manual Addendum Firmware Version V3 It is very important that you read this document in its entirety before using the V3 firmware. Some features behave differently than they

More information

Operating Station Equipment

Operating Station Equipment Amateur Radio License Class Operating Station Equipment Presented by Steve Gallafent October 3, 2007 Operating Station Equipment Modulation Modulation is the process of adding information to a radio signal

More information

Second Hand Yaesu FTDX5000MP HF base station transceiver

Second Hand Yaesu FTDX5000MP HF base station transceiver 263 Walsall Road, Great Wyrley, Walsall, WS6 6DL Established 1997. Open Monday - Friday 9am - 5pm and Saturday 9.30am - 4pm Tel: 01922 414 796 Fax: 01922 417829 Skype: radioworld_uk Second Hand Yaesu FTDX5000MP

More information

TABLE OF CONTENTS. Magnum International PO Box 445 Issaquah, WA 98027

TABLE OF CONTENTS. Magnum International PO Box 445 Issaquah, WA 98027 OPERATING MANUAL TABLE OF CONTENTS Limited Warranty... 2 Introduction... 3 Installation...3-4 Front Panel Controls and Functions...4-7 Other Features... 7 Specifications... 8 LIMITED WARRANTY Magnum International

More information

Applications: FM wireless audio, USB PC audio broadcasting, wireless microphones, maternal and child care.

Applications: FM wireless audio, USB PC audio broadcasting, wireless microphones, maternal and child care. Product Description 1: The use of advanced digital audio signal processing (DSP) technology and FM modulation phase-locked loop (PLL) to make sound more realistic, more stable performance, long working

More information

TS-590S ADJUSTMENT. Updating the Firmware. Required Test Equipment. Preparation

TS-590S ADJUSTMENT. Updating the Firmware. Required Test Equipment. Preparation Updating the Firmware The firmware of the main MCU and DSP can be updated using the TS590 Update update software. Update the firmware according to the procedure displayed in update software. Refer to the

More information

LT-800 Stationary FM Transmitter

LT-800 Stationary FM Transmitter LT-800 Stationary FM Transmitter Thanks to its outstanding audio quality, the Listen LT-800 Stationary Transmitter can be used in a variety of applications. The LT-800 is connected to your main audio system,

More information

14 CHANNEL FAMILY RADIO SYSTEM MODEL # FR142

14 CHANNEL FAMILY RADIO SYSTEM MODEL # FR142 14 CHANNEL FAMILY RADIO SYSTEM MODEL # FR142 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in China 128-6020 052FR142104 BEFORE OPERATING THIS PRODUCT PLEASE READ THESE INSTRUCTIONS COMPLETELY

More information

Testing Motorola P25 Conventional Radios Using the R8000 Communications System Analyzer

Testing Motorola P25 Conventional Radios Using the R8000 Communications System Analyzer Testing Motorola P25 Conventional Radios Using the R8000 Communications System Analyzer Page 1 of 24 Motorola CPS and Tuner Software Motorola provides a CD containing software programming facilities for

More information

1. Your new Eagle 599 3

1. Your new Eagle 599 3 Table of Contents 1. Your new Eagle 599 3 1.1. Unpacking Eagle 599 3 1.2. About this Manual 3 1.3. Accessory package 3 1.4. Connection to Antenna & Power Supply 4 1.5. A word about grounding 4 1.6. Philosophy

More information

KENWOOD SKY COMMAND SYSTEM

KENWOOD SKY COMMAND SYSTEM KENWOOD SKY COMMAND SYSTEM Operation Manual KENWOOD COMMINICATIONS CORPORATION KENWOOD COMMUNICATIONS CORPORATION This operation manual is used for the KENWOOD SKY COMMAND SYSTEM (hereinafter referred

More information

LT-800 Stationary Transmitter

LT-800 Stationary Transmitter LT-800 Stationary Transmitter Configuration Stationary FM Transmitter (72 MHz) Stationary FM Transmitter (216 MHz) Stationary FM Transmitter (863 MHz) Thanks to its outstanding audio quality, the Listen

More information

USER MANUAL. CommRadio CR-1 Communications Receiver

USER MANUAL. CommRadio CR-1 Communications Receiver USER MANUAL CommRadio CR-1 Communications Receiver AeroStream Communications CommRadio Division 1717 Washington Ave Suite 10 Golden, Colorado 80401 USA 303-279-3671 Email: support@commradio.com www.commradio.com

More information

TECSUN PL-365. FM stereo / MW / SW-SSB DSP RECEIVER OPERATION MANUAL ELECTRONIC IND. LTD. RADIOS AUSTRALIA

TECSUN PL-365. FM stereo / MW / SW-SSB DSP RECEIVER OPERATION MANUAL ELECTRONIC IND. LTD. RADIOS AUSTRALIA TECSUN TECSUN RADIOS AUSTRALIA PL-365 FM stereo / MW / SW-SSB DSP RECEIVER OPERATION MANUAL TECSUN PL-365 FM STEREO/MW/SW-SSB DSP RECEIVER TECSUN RADIOS TECSUN AUSTRALIA ELECTRONIC IND. LTD. PL-365 Functional

More information

IC-F7000. Advanced selective call and ALE make HF communication easier than ever!

IC-F7000. Advanced selective call and ALE make HF communication easier than ever! Page 1 of 5 HF TRANSCEIVER IC-F7000 Advanced selective call and ALE make HF communication easier than ever! The IC-F7000 is an HF land mobile transceiver especially designed forlong distance communications.

More information

Pushing performance to the pinnacle

Pushing performance to the pinnacle Pushing performance to the pinnacle The latest DSP technologies developed for the IC-7800/7700 plus over 45 years of analog circuit expertise give the IC-7600 the performance advantage. The flagship's

More information

Operation Manual. SlJPER ST AR Channel Mobile 5-Mode Transceiver -----~- --:.. KTSS200NXX ,, I

Operation Manual. SlJPER ST AR Channel Mobile 5-Mode Transceiver -----~- --:.. KTSS200NXX ,, I Operation Manual!.,, SlJPER ST AR 2000 200 Channel Mobile 5-Mode Transceiver -----~- --:.. KTSS200NXX General Description l Frequency/Channel Chart The Super Star -2000 is a combination transmitter-receiver

More information

AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL

AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL AM/FM/SSB/CW 12 & 10 METER MOBILE AMATEUR TRANSCEIVER OWNER S MANUAL TABLE OF CONTENTS Warranty...2 Introduction...3 Installation... 4-5 Front Panel Controls... 6-8 Microphone...8 Menu Settings... 9-11

More information

PLL SYNTHESIZED RECEIVER FM STEREO / MW / LW / SW-SSB / AIR BAND OPERATION MANUAL TECSUN PL-660. Shortwave BW

PLL SYNTHESIZED RECEIVER FM STEREO / MW / LW / SW-SSB / AIR BAND OPERATION MANUAL TECSUN PL-660. Shortwave BW PL-660 PLL SYNTHESIZED RECEIVER FM STEREO / MW / LW / SW-SSB / AIR BAND OPERATION MANUAL TECSUN Shortwave BW FAST khz SYNC USB PL-660 AM SYNCHRONOUS DETECTOR FM STEREO/LW/MW/SW-SSB/AIR PLL SYNTHESIZED

More information

Model: TP380 User Manual

Model: TP380 User Manual Model: TP380 User Manual 1 UHF RADIO TRANSCEIVER MODEL: TP380 USER MANUAL INTRODUCTION Thank you for selecting the Oregon Scientific TP380 as your product of choice. This product is a portable, easy-to-use

More information

IC-400pro - RADIOAFICION.COM

IC-400pro - RADIOAFICION.COM PROCEDURES IC-400pro - 5- PREPARATION When you adjust the contents on pages 5-5 and 5-6, SOFT- WARE, the optional CS-400PRO ADJ SOFTWARE (Rev..0 or later), *OPC- JIG CABLE (modified OPC- CLONING CABLE;

More information

WTI-100 Simplex wireless Interface Instruction Manual

WTI-100 Simplex wireless Interface Instruction Manual TELIKOU Intercom System WTI-100 Simplex wireless Interface Instruction Manual 2006 TELIKOU Systems All Rights Reserved www.telikou.com While TELIKOU makes every attempt to maintain the accuracy of the

More information

Midland 248XL I NSTRUCTION GUI DE

Midland 248XL I NSTRUCTION GUI DE Midland 248XL I NSTRUCTION GUI DE INDEX Introduction...2 Function and location of the controls...3 Installation...7 Power supply...7 Installing an antenna...7 How to use your Midland 248XL...8 Frequency

More information

DMR Application Note Testing MOTOTRBO Radios On the R8000 Communications System Analyzer

DMR Application Note Testing MOTOTRBO Radios On the R8000 Communications System Analyzer DMR Application Note Testing MOTOTRBO Radios On the R8000 Communications System Analyzer April 2 nd, 2015 MOTOTRBO Professional Digital Two-Way Radio System Motorola and MOTOTRBO is registered in the U.S.

More information

TABLE OF CONTENTS 8 SOFTWARE MENU MODE SETTINGS SOFTWARE MENU QUICK GUIDE SERVICE MODE... 24

TABLE OF CONTENTS 8 SOFTWARE MENU MODE SETTINGS SOFTWARE MENU QUICK GUIDE SERVICE MODE... 24 1 TABLE OF CONTENTS 1. TABLE OF CONTENTS......................... 2 2. INTRODUCTION............................. 3 3. SPECIFICATIONS............................ 4 4. ACCESSORY PACKAGE.......................

More information

INSTALLATION AND OPERATION GUIDE

INSTALLATION AND OPERATION GUIDE VHF Marine Radio RT-311 INSTALLATION AND OPERATION GUIDE Navicom plaisance: Z.A. des Boutries, 78700 Conflans Ste Honorine Tel: 01.39.72.19.90 Fax: 01.39.19.28.98 Navicom Pro: 3, rue J. Cugnot, Z.A.C Petit

More information

Application Note: DMR Application Note Testing MOTOTRBO Radios On the Freedom Communications System Analyzer

Application Note: DMR Application Note Testing MOTOTRBO Radios On the Freedom Communications System Analyzer : DMR Application Note Testing MOTOTRBO Radios On the Freedom Communications System Analyzer MOTOTRBO Professional Digital Two-Way Radio System Motorola and MOTOTRBO is registered in the U.S. Patent and

More information

Application Note: Testing P25 Conventional Radios Using the Freedom Communications System Analyzers

Application Note: Testing P25 Conventional Radios Using the Freedom Communications System Analyzers : Testing P25 Conventional Radios Using the Freedom Communications System Analyzers FCT-1007A Motorola CPS and Tuner Software Motorola provides a CD containing software programming facilities for the radio

More information

PC Tune PC Tune Test Procedures for 5100 Series Portable Radios

PC Tune PC Tune Test Procedures for 5100 Series Portable Radios PC Tune PC Tune Test Procedures for 5100 Series Portable Radios Part Number 002-9998-6513014 August 2008 Copyright 2006, 2007, 2008 by EFJohnson Technologies The EFJohnson Technologies logo, PC Configure,

More information

RM Italy HLA-305V HF Amplifier Test Report

RM Italy HLA-305V HF Amplifier Test Report RM Italy HLA-305V HF Amplifier Test Report By Adam Farson VA7OJ/AB4OJ P.O. Box 91105, West Vancouver BC V7V 3N3, Canada Iss. 2, April 30, 2015 Figure 1: HLA-305V HF Amplifier, with cooling fans.. Introduction:

More information

UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz)

UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz) UNIVERSAL-DDS-VFO UDV ( 1 Hz to 10 MHz) Connection and operating instructions 1. Introduction The UDV is the ideal device to adapt older, VFO-controlled transceivers to modern requirements regarding frequency

More information

Zeon PDF Driver Trial

Zeon PDF Driver Trial 401 W. 35th Street, Suite B National City, CA 91950 (800)446-5778. FAX( 619)426-3788 Email : rci@rangerusa.com http : //www.rangerusa.com Printed In Malaysia AT6960A11A PD000619 TR-936 SOLID STATE CITIZENS

More information

S5101 Handheld Radio Communication Analyzer

S5101 Handheld Radio Communication Analyzer is the ideal radio tester for laboratory, production, service and maintenance use. It combines radio frequency emission, reception analysis, audio source, analyzer, etc. all into one unit. It can measure

More information

Pair of PMR446 Two-Way Personal Radios Model: TP391

Pair of PMR446 Two-Way Personal Radios Model: TP391 Pair of PMR446 Two-Way Personal Radios Model: TP391 USER MANUAL MANUALE D USO MANUEL DE L UTILISATEUR BEDIENUNGSANLEITUNG MANUAL DE USUARIO MANUAL DO USUÁRIO HANDLEIDING BRUKSANVISNING P/N:086L004722-016

More information

SUPERSTAR TABLE OF CONTENTS AM/FM/USB/LSB/CW AMATEUR MOBILE TRANSCEIVER WITH BUILT-IN FREQUENCY COUNTER OWNER S MANUAL

SUPERSTAR TABLE OF CONTENTS AM/FM/USB/LSB/CW AMATEUR MOBILE TRANSCEIVER WITH BUILT-IN FREQUENCY COUNTER OWNER S MANUAL SUPERSTAR TABLE OF CONTENTS AM/FM/USB/LSB/CW AMATEUR MOBILE TRANSCEIVER WITH BUILT-IN FREQUENCY COUNTER PAGE CHAPTER 1 Specifications............................................... 2 CHAPTER 2 Installation.................................................

More information

Owner s Manual For Models G-225 & G-227 GMRS/FRS Radio

Owner s Manual For Models G-225 & G-227 GMRS/FRS Radio Owner s Manual For Models G-225 & G-227 GMRS/FRS Radio FEATURING 22 Channels 38 CTCSS codes VOX Monitor function Call Alert Back-Lit LCD Vibrate Alert (G-227 Only) Scan Roger Beep Tone This device complies

More information

HF/50MHz TRANSCEIVER

HF/50MHz TRANSCEIVER HF/50MHz TRANSCEIVER D isplay Pushing performance to the pinnacle The latest DSP technologies developed for the flagship models plus many decades of analog circuit expertise give the the performance advantage.

More information

BridgeCom Systems D Centimeter DMR and Analog Handheld Transceiver

BridgeCom Systems D Centimeter DMR and Analog Handheld Transceiver Product TechnicalReview Mark by Mark J. Wilson, Spencer, K1RO, WA8SME k1ro@arrl.org BridgeCom Systems D-500 70-Centimeter DMR and Analog Handheld Transceiver This solid radio offers an easy entry point

More information

HF SIGNALS ΜBITX. The QRP HF General Coverage Transceiver you can build. Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks

HF SIGNALS ΜBITX. The QRP HF General Coverage Transceiver you can build. Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks Page 1 of 5 HF SIGNALS ΜBITX The QRP HF General Coverage Transceiver you can build Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks ($109 USD) Page 2 of 5 The µbitx is a general coverage

More information

RL /430MHZ DUAL BAND FM TRANSCEIVER OPERATION INSTRUCTION

RL /430MHZ DUAL BAND FM TRANSCEIVER OPERATION INSTRUCTION RL-502 144/430MHZ DUAL BAND FM TRANSCEIVER OPERATION INSTRUCTION RoHS Table of Contents Packing List...1 Cautions...2 Parts Name & Functions...3 Fitting & Removing the Battery Pack...4 Installation the

More information

PAMS. User s Manual. Portable Attenuation Measurement System. The solution for making easy shielding effectiveness measurements.

PAMS. User s Manual. Portable Attenuation Measurement System. The solution for making easy shielding effectiveness measurements. PAMS Portable Attenuation Measurement System User s Manual The solution for making easy shielding effectiveness measurements. 310-010042-001 TABLE OF CONTENTS Warranty Statement 1 Chapter 1 General Information

More information

Improved performance and mobility for more applications. Delivering a new standard for high performance in complete wireless microphone systems, TOA

Improved performance and mobility for more applications. Delivering a new standard for high performance in complete wireless microphone systems, TOA Improved perfmance and mobility f me applications. Delivering a new standard f high perfmance in complete wireless microphone systems, TOA provides a full range of wireless microphones optimized f general

More information

AE 497 W (25-30 W-Version)

AE 497 W (25-30 W-Version) User Manual AE 497 W (25-30 W-Version) 10-Meter Amateur Radio Base Station Legal notes and general information This amateur radio base station complies to the minimum requirements of the EU directives

More information

RU210. Dual Multi-UHF Wireless System. Item ref: UK, UK User Manual. Version 1.0

RU210. Dual Multi-UHF Wireless System. Item ref: UK, UK User Manual. Version 1.0 RU210 Dual Multi-UHF Wireless System Item ref: 171.970UK, 171.971UK User Manual Version 1.0 Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty

More information

Dear Valued Customer,

Dear Valued Customer, Dear Valued Customer, Thank you for choosing Listen! All of us at Listen are dedicated to provide you with the highest quality products available. We take great pride in their outstanding performance because

More information

Introduction Pag. 1. Function and location of the controls Pag. 2. Installation Pag. 3. Power supply Pag. 3. Installing an antenna Pag.

Introduction Pag. 1. Function and location of the controls Pag. 2. Installation Pag. 3. Power supply Pag. 3. Installing an antenna Pag. ALAN 121 INDEX Introduction Pag. 1 E N G L I S H Function and location of the controls Pag. 2 Installation Pag. 3 Power supply Pag. 3 Installing an antenna Pag. 4 How to operate with your transceiver Pag.

More information

Yaesu FT-25R 2-Meter Handheld Transceiver

Yaesu FT-25R 2-Meter Handheld Transceiver Yaesu FT-25R 2-Meter Handheld Transceiver Reviewed by Dan Wall, W1ZFG ARRL LoTW Administration w1zfg@arrl.org The latest entry into the field of small, inexpensive handhelds is the Yaesu FT-25R. This is

More information

FCC STATEMENT This device complies with part 74, Subpart H of the FCC rules. Operation is subject to the following two conditions: (1)This device may

FCC STATEMENT This device complies with part 74, Subpart H of the FCC rules. Operation is subject to the following two conditions: (1)This device may FCC STATEMENT This device complies with part 74, Subpart H of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference and (2) This device

More information

User Manual. ilive 2 Wireless microphone system

User Manual. ilive 2 Wireless microphone system User Manual ilive 2 Wireless microphone system Safety instructions When using this electronic device, basic precautions should always be taken, including the following: 1 Read all instructions before using

More information

DELUXE 18CHANNEL SSB/AM CB TRANSCEIVER OWNER'S GUIDE

DELUXE 18CHANNEL SSB/AM CB TRANSCEIVER OWNER'S GUIDE DELUXE 18CHANNEL SSB/AM CB TRANSCEIVER OWNER'S GUIDE General Description The Bush Ranger is a combination transmitter and receiver designed for use in the Australian 27 MHz Citizens radio service. It is

More information

evolution wireless G4 ew 300 G4-Base SK-RC Bodypack Base Set

evolution wireless G4 ew 300 G4-Base SK-RC Bodypack Base Set 1/7 Best choice for your business, top of the class in education. The G4 300 Series uses the power of an increased switching bandwidth of up to 88 MHz. New frequency ranges allow to operate multi-channel

More information

Installation... 3 Installing The Radio... 3 Ignition Noise Interference... 4 Antenna... 4 External Speaker... 4 Public Address...

Installation... 3 Installing The Radio... 3 Ignition Noise Interference... 4 Antenna... 4 External Speaker... 4 Public Address... TABLE OF CONTENTS CHAPTER 1 Specifications.............................................. 2 PAGE BIG RIG SERIES S 1 MOD PW R 20 0 3 SW R 40 1 5 5 60 1.5 7 10 2 9 20 80 3 30 +20 40 50 +40 100% MAX db +60

More information

TLKR T60 OWNER'S MANUAL EN DE FR IT ES PR NL DA NO TU PL SV RU

TLKR T60 OWNER'S MANUAL EN DE FR IT ES PR NL DA NO TU PL SV RU TLKR T60 OWNER'S MANUAL EN DE FR IT ES PR NL DA NO TU PL SV RU SF 1 PRODUCT SAFETY AND RF EXPOSURE FOR PORTABLE TWO-WAY RADIOS! Caution ATTENTION! Before using this product, read the RF energy awareness

More information

200GTL ALIGNMENT REVISION: 1.0 BURKE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06. Total Pages: 6 pages. Page:1 print date: 9/23/09

200GTL ALIGNMENT REVISION: 1.0 BURKE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06. Total Pages: 6 pages. Page:1 print date: 9/23/09 ALIGNMENT PROCEDURE MODEL: 200GTL REVISION: 1.2 DATE: 02/14/06 PREPARED BY: BURKE Total Pages: 6 pages Page:1 print date: 9/23/09 1 TEST CONDITION: 200GTL ALIGNMENT INSTRUCTION 1.0. TEST TEMPERTAURE: 77

More information

E L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E

E L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E E L E C R A F T K 2 R E V I S I O N 2 F I R M W A R E Installation and Reference Manual Rev. B, August 28, 2001 Summary of Changes... 2 Computer Control (KIO2)... 2 Transverter Bands... 2 RTTY/Data Mode

More information

The Mountain Topper by Steve Weber (KD1JV) (MTR) www.lnrprecision.com FULLY ASSEMBLED Manufactured by LNR Precision, Inc. A very small, very efficient three band QRP CW rig. Specifications: Three bands,

More information

FREQUENCY SYNTHESIZERS, SIGNAL GENERATORS

FREQUENCY SYNTHESIZERS, SIGNAL GENERATORS SYNTHESIZED SIGNAL GENERATOR MG3641A/MG3642A 12 khz to 1040/2080 MHz NEW New Anritsu synthesizer technology permits frequency to be set with a resolution of 0.01 Hz across the full frequency range. And

More information

Langton House, 19 Village Street, Harvington, Worcestershire. WR11 8NQ Tel: Fax: RTB5211 UHF FULL DUPLEX BASE STATION

Langton House, 19 Village Street, Harvington, Worcestershire. WR11 8NQ Tel: Fax: RTB5211 UHF FULL DUPLEX BASE STATION Langton House, 19 Village Street, Harvington, Worcestershire. WR11 8NQ Tel:- 01789 777040 Fax:- 01789 881330 RTB5211 UHF FULL DUPLEX BASE STATION OPERATORS MANUAL Print Date 31/10/2008 Page 1 of 10 E2057-00MA-01.doc

More information

Talkabout T82/ T82 EXTREME OWNER S MANUAL

Talkabout T82/ T82 EXTREME OWNER S MANUAL Talkabout T82/ T82 EXTREME OWNER S MANUAL B RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety

More information

SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone

SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone SEA 235 OPERATOR S MANUAL Digital Single Sideband Radiotelephone TABLE OF CONTENTS GENERAL OPERATIONS...1 TECHNICAL SPECIFICATIONS...1 GENERAL INFORMATION...2 UNDERSTANDING CHANNEL MEMORY...3 LCD DISPLAY

More information

Important safety instructions

Important safety instructions RCR-29 GB Version 1 Important safety instructions VERY IMPORTANT PLEASE READ Sangean suggest that you keep your AC Adapter at least 12 inches away from the radio while listening to the AM Band. Your Sangean

More information

Technician License Course Chapter 3 Types of Radios and Radio Circuits. Module 7

Technician License Course Chapter 3 Types of Radios and Radio Circuits. Module 7 Technician License Course Chapter 3 Types of Radios and Radio Circuits Module 7 Radio Block Diagrams Radio Circuits can be shown as functional blocks connected together. Knowing the description of common

More information

PPA 377. Personal PA FM Listening System FM SPECIFICATION DATA. System Includes:

PPA 377. Personal PA FM Listening System FM SPECIFICATION DATA. System Includes: FM SPECIFICATION DATA Churches Schools Auditoriums Conference Rooms Theaters PPA 377 Personal PA FM Listening System The PPA 377 features the T35 high performance transmitter: powerful microprocessor,

More information