CAT (COMPUTER AIDED TRANSCEIVER) OPERATION

Transcription

1 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN FTD5000 SERIES CAT PERATIN REFERENCE BK FTD5000 SERIES CAT PERATIN REFERENCE

2 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN VERVIEW The CAT (Computer Aided Transceiver) System in the FTD5000 series provides control of frequency, VF, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated as single mouse clicks or keystroke operations on the computer keyboard. The FTD5000 series has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. You will need a serial cable for connection to the RS-232C (serial or CM port) connector on your computer. Purchase a standard serial cable (not the so-called null modem type), ensuring it has the correct gender and number of pins (some serial CM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Vertex Standard does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs later on for your operating needs and discover the true operating potential of this system. PIN N. PIN NAME N/A SERIAL UT SERIAL IN N/A GND N/A RTS CTS N/A CAT JACK I/ utput Input Input utput FUNCTIN utputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. Signal Ground When the computer is not ready to receive data, this port goes to L for inhibit the transmit data from the transceiver. When the transceiver is not ready to receive data, this port goes to L for inhibit the transmit data from the computer. CM CAT RS-232C "Straght" Cable Page 1 FTD5000 SERIES CAT PERATIN REFERENCE

3 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: Set the main band (VF-A) frequency to MHz. FA ; Command Parameter Terminator There is three for the FTD5000 Command as shown below: Set command: Set a particular condition (to the FTD5000) Read command: Reads an answer (from the FTD5000) Answer command: Transmits a condition (from the FTD5000) For example, note the following in the case of the FA command (Set the main band (VF-A) frequency): To set the main band (VF-A) frequency to MHz, the following command is sent from the computer to the transceiver: FA ; (Set command) To read the main band (VF-A) frequency, the following command is sent from the computer to the transceiver: FA; (Read command) When the Read command above has been sent, the following command is returned to the computer: FA ; (Answer command) Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. CNTRL CMMAND Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when correct parameter is IS (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (nly three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS ; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FTD5000, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. FTD5000 SERIES CAT PERATIN REFERENCE Page 2

4 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND LIST CMMAND FUNCTIN SET READ ANS. AI AB AC AG AI AM AN BA BC BD BI BP BS BU BY CA CH CN C CS CT DA DN DP DS ED EU E FA FB FR FS FT GT ID IF IS KM KP KR KS KY LK LM MA MC MD MG MK ML VF-A T VF-B ANTENNA TUNER CNTRL AF GAIN AUT INFRMATIN VF-A T MEMRY CHANNEL ANTENNA NUMBER VF-B T VF-A AUT NTCH BAND DWN BREAK-IN MANUAL NTCH BAND SELECT BAND UP BUSY CLASS-A CHANNEL UP/DWN CTCSS NUMBER CNTUR CW SPT CTCSS DIMMER DWN DISPLAY DIMMER SWITCH ENCRDER DWN ENCRDER UP MENU FREQUENCY VF-A FREQUENCY VF-B FUNCTIN R FAST STEP FUNCTIN T AGC FUNCTIN IDENTIFICATIN INFRMATIN IF-SHIFT KEYER MEMRY KEY PITCH KEYER KEY SPEED CW KEYING LCK LAD MESSAGE MEMRY CHANNEL T VF-A MEMRY CHANNEL MDE MIC GAIN MDE KEY MNITR LEVEL CMMAND FUNCTIN SET READ ANS. AI MR MS MW M NA NB NL NR I S PA PB PC PL PR PS QI QR QS RA RC RD RF RG RI RL RM R RS RT RU SC SD SF SH SM SQ SV TS T UL UP VD VF VG VM VS V T MEMRY READ METER SW MEMRY WRITE M SET NARRW NISE BLANKER NISE BLANKER LEVEL NISE REDUCTIN PPSITE BAND INFRMATIN FFSET (REPEATER SHIFT) PRE-AMP (IP) PLAY BACK PWER CNTRL SPEECH PRCESSR LEVEL SPEECH PRCESSR PWER SWITH QMB STRE QMB RECALL QUICK SPLIT RF ATTENUATR CLAR CLEAR CLAR DWN RFING FILTER RF GAIN RADI INFRMATIN NISE REDUCTIN LEVEL READ METER RTATR RADI STATUS CLAR CLAR UP SCAN SEMI BREAK-IN DELAY TIME SUB-DIAL FUNCTIN WIDTH S METER SQUELCH LEVEL SWAP VF TW T SET UNLCK UP V DELAY TIME VRF FILTER V GAIN [V/M] KEY FUNCTIN VF SELECT V T CLAR Page 3 FTD5000 SERIES CAT PERATIN REFERENCE

5 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN AB VF-A T VF-B A B ; CNTRL CMMAND TABLES AC ANTENNA TUNER CNTRL A C P2 P3 ; A C ; A C P2 P3 ; 0: Fixed P3 0: Tuner FF P2 0: Fixed 1: Tuner N 2: Tuning Start AG AF GAIN A G P2 P2 P2 ; A G ; A G P2 P2 P2 ; AI AUT INFRMATIN A I ; A I ; A I ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P : Auto Information FF 1: Auto Information N This parameter is set to 0 (FF) automatically when the transceiver is turned FF. AM VF-A T MEMRY CHANNEL A M ; AN ANTENNA NUMBER A N P2 ; A N ; A N P3 P4 ; 0: Main (VF-A) Band 1: Sub (VF-B) Band P2 1: ANT 1 2: ANT 2 3: ANT 3 4: ANT 4 5: ANT R P3 1: ANT 1 2: ANT 2 3: ANT 3 4: ANT 4 P4 0: ANT R FF 1: ANT R N BA VF-B T VF-A B A ; BC AUT NTCH B C P2 ; B C ; B C P2 ; BD BAND DWN B D ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: Auto Notch FF 1: Auto Notch N 0: Main (VF-A) Band 1: Sub (VF-B) Band FTD5000 SERIES CAT PERATIN REFERENCE Page 4

6 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES BI BREAK-IN B I ; B I ; B I ; BP MANUAL NTCH B P P2 P3 P3 P3 ; B P P2 ; B P P2 P3 P3 P3 ; BS BAND SELECT B S ; 0: Break-in FF 1: Break-in N 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: Manual NTCH N/FF 1: Manual NTCH LEVEL 00: 1.8 MHz 06: 18 MHz 01: 3.5 MHz 07: 21 MHz 02: - 08: 24.5 MHz 03: 7 MHz 09: 28 MHz 04: 10 MHz 10: 50 MHz 05: 14 MHz 11: GEN P3 When P2=0 000: FF 001: N When P2= (NTCH Frequency : x 10 Hz ) BU BAND UP B U ; 0: Main (VF-A) Band 1: Sub (VF-B) Band BY BUSY B Y ; B Y P2 ; CA CLASS-A C A P2 P2 P2 ; C A ; C A P2 P2 P2 ; CH CHANNEL UP/DWN C H ; 0: Main (VF-A) Band BUSY FF 1: Main (VF-A) Band BUSY N P2 0: Sub (VF-B) Band BUSY FF 1: Sub (VF-B) Band BUSY N 0:CLASS-A N/FF 1: BIAS LEVEL P2 When =0 000: FF 001: N When = : Memory Channel UP 1: Memory Channel DWN CN CTCSS TNE FREQUENCY C N P2 P2 ; C N ; C N P2 P2 ; P2 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver 0-49: Tone Frequency Number Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz Hz 94.8 Hz 97.4 Hz Hz Hz Hz Hz Hz Hz CTCSS TNE CHART Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Hz Page 5 FTD5000 SERIES CAT PERATIN REFERENCE

7 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES C CNTUR C P2 P3 P3 ; C P2 ; C P2 P3 P3 ; CS CW SPT C S ; C S ; C S ; CT CTCSS C T P2 ; C T ; C T P2 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: CNTUR/APF N/FF 1: CNTUR FREQUENCY 0: FF 1: N 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: CTCSS FF 1: CTCSS ENC/DEC N 2: CTCSS ENC N P3 When P2=0, 000: CNTUR/APF FF 001: CNTUR N 002: APF N When P2=1, (CNTUR FREQUENCY) 100 ~ 4000 Hz DA DIMMER D A P2 P2 P3 P3 P4 P4 D A ; D A P2 P2 P3 P3 P4 P4 Set ; Read P2 P3 P : VFD Backlight Brightness Level 00-15: Meter Brightness Level 00-15: LE Brightness Level 00-15: ELCD (SM-5000) Brightness Level Answer ; DN MIC DWN D N ; DP DISPLAY D P ; D P ; D P ; DS DIMMER SWITCH D S ; D S ; D S ; ED ENCRDER DWN E D P2 P2 ; P2 0: World Clock Display 1: Band Scope Display 2: AF scilloscope/spectrum Analyzer Display 3: Log Book Display 4: Temperature/SWR Display 5: Rotator Display 6: Memory Channel List Display 0: DIMMER FF 1: DIMMER N 0: MAIN ENCRDER 1: SUB ENCRDER 2: MAIN Select 3: SUB Select 01-99: Steps : This command does not activates when the optional Data Managemnt Unit is not attached. FTD5000 SERIES CAT PERATIN REFERENCE Page 6

8 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES EU ENCRDER UP E U P2 P2 ; P2 0: MAIN ENCRDER 1: SUB ENCRDER 2: MAIN Select 3: SUB Select 01-99: Steps E MENU Set nn ** E P2 P2 ~ P2 ; E ; Answer nn ** E P2 P2 ~ P2 ; : (MENU Number) P2 : Parameter See Table 1 - Table 3 TABLE 1 FUNCTIN P2 BYTE 001 MAIN-FAST-DELAY 0020~4000 (20msec/step) MAIN-FAST-HLD 0000~2000 (20msec/step) MAIN-MID-DELAY 0020~4000 (20msec/step) MAIN-MID-HLD 0000~2000 (20msec/step) MAIN-SLW-DELAY 0020~4000 (20msec/step) MAIN-SLW-HLD 0000~2000 (20msec/step) TFT CLR 0: CL BLUE, 1: CNTRAST BLUE, 2: FLASH WHITE, 3: CNTRAST UMBER, 4: UMBER DIMMER-METER 00~ DIMMER-VFD 00~ DIMMER-LE 00~ DIMMER-E.LCD 00~ BAR DISPLAY SELECT 0: CLAR, 1: CW TUNE SUB MTR PEAK HLD 0: FF, 1: 0.5, 2: 1.0, 3: 2.0 (sec) RTATR START UP 0: 0, 1: 90, 2: 180, 3: RTATR FFSET ADJ -30~0 (P2 = 30~00) (2 step) QMB MARKER 0: DISABLE, 1: ENABLE LEVEL INDICATR ~ (see Page 9) INDICATR 0: VFD, 1: EL SELECT 0: PTN1, 1: PTN R UT LEVEL 000~ T UT LEVEL 000~ BEACN TIME FF/001~255sec (0: FF) NUMBER STYLE 0: 1290, 1: AUN, 2: AUNT, 3: A2N, 4: A2NT, 5: 12N, 6: 12NT CNTEST NUMBER 0000~ CW MEMRY 1 0: TET, 1: MESSAGE CW MEMRY 2 0: TET, 1: MESSAGE CW MEMRY 3 0: TET, 1: MESSAGE CW MEMRY 4 0: TET, 1: MESSAGE CW MEMRY 5 0: TET, 1: MESSAGE ANT SELECT 0: BAND, 1: STACK BEEP LEVEL 000~ CAT RATE 0: 4800, 1: 9600, 2: 19200, 3: (bps) CAT TIME UT TIMER 0: 10, 1: 100, 2: 1000, 3: 3000 (msec) CAT RTS 0: DISABLE, 1: ENABLE CAT DATA INDICATR 0: DISABLE, 1: ENABLE MEM GRUP 0: DISABLE, 1: ENABLE QUICK SPLIT FREQ -20 ~ +20 khz (P2 = -20 ~ +00 ~ +20) TRACKING 0: FF, 1: BAND, 2: FREQ TIME UT TIMER FF/01~30min TRV FFSET (14MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) TRV FFSET (28MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) TRV FFSET (50MHz) 30: 30, 31: 31, 32: 32 ~ 44: 44, 45: 45, 46: 46 (MHz) utune DIAL STEP 0: DIAL STEP-2, 1: DIAL STEP-1, 2: FF MIC SCAN 0: DISABLE, 1: ENABLE MIC SCAN RESUME 0: PAUSE, 1: TIME FREQ ADJ -25~0~+25 (P2 = -25 ~ +00 ~ +25) AM LCUT FREQ 00: FF, 01: 100Hz, ~, 19: 1000Hz (50Hz/step) AM LCUT SLPE 0: 6dB/oct, 1: 18dB/oct AM HCUT FREQ 00: FF, 01: 700Hz, ~, 67: 4000Hz (50Hz/step) AM HCUT SLPE 0: 6dB/oct, 1: 18dB/oct AM MIC GAIN MCVR/FI(0~100) (P2 = 1000: MCVR, 0000~0100: FI(0~100)) AM MIC SEL 0: FRNT, 1: DATA, 2: PC CW LCUT FREQ 00: FF, 01: 100Hz, ~, 19: 1000Hz (50Hz/step) CW LCUT SLPE 0: 6dB/oct, 1: 18dB/oct CW HCUT FREQ 00: FF, 01: 700Hz, ~, 67: 4000Hz (50Hz/step) CW HCUT SLPE 0: 6dB/oct, 1: 18dB/oct F-KEYER TYPE 0: FF, 1: BUG, 2: ELEKEY, 3: ACS F-CW KEYER 0: NR, 1: REV R-KEYER TYPE 0: FF, 1: BUG, 2: ELEKEY, 3: ACS R-CW KEYER 0: NR, 1: REV CW AUT MDE 0: FF, 1: 50M, 2: N CW BF 0: USB, 1: LSB, 2: AUT CW BK-IN 0: SEMI, 1: FULL CW WAVE SHAPE 0: 1, 1: 2, 2: 4, 3: 6 (msec) CW WEIGHT 2.5~3.0~4.5 (P2 = 25~45) CW FREQ DISPLAY 0: DIRECT FREQ, 1: PITCH FFSET PC KEYING 0: DISABLE, 1: ENABLE 1 Page 7 FTD5000 SERIES CAT PERATIN REFERENCE

9 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES TABLE 2 FUNCTIN P2 BYTE 068 QSK 0: 15, 1: 20, 2: 25, 3: 30 (msec) DATA IN SELECT 0: DATA, 1: PC DATA T GAIN 000~ DATA UT 0: VF-A, 1: VF-B DATA UT LEVEL 000~ DATA V DELAY 0030~0300~3000msec (10msec/step) DATA V GAIN 000~ FM LCUT FREQ 00: FF, 01: 100Hz, ~, 19: 1000 Hz (50Hz/step) FM LCUT SLPE 0: 6, 1: 18 (db/oct) FM HCUT FREQ 00: FF, 01: 700, ~, 67: 4000 Hz (50Hz/step) FM HCUT SLPE 0: 6, 1: 18 (db/oct) FM MIC GAIN MCVR/FI(0~100) (P2 = 1000: MCVR, 0000~0100: FI(0~100)) FM MIC SEL 0: FRNT, 1: DATA, 2: PC RPT SHIFT(28MHz) 0000 ~0100 ~ 1000 khz (10Hz/step) RPT SHIFT(50MHz) 0000 ~0100 ~ 1000 ~ 4000 khz (10Hz/step) PKT LCUT FREQ 00: FF, 01: 100Hz, ~, 19: 1000 Hz (50Hz/step) PKT LCUT SLPE 0: 6, 1: 18 (db/oct) PKT HCUT FREQ 00: FF, 01: 700, ~, 67: 4000 Hz (50Hz/step) PKT HCUT SLPE 0: 6, 1: 18 (db/oct) PKT DISP (SSB) ~ 0 ~ Hz (10Hz/step) (P2 = ~ ~ +3000) PKT SHIFT (SSB) ~ 0 ~ Hz (10Hz/step) (P2 = ~ ~ +3000) RTTY LCUT FREQ 00: FF, 01: 100, ~, 19: 1000 Hz (50Hz/step) RTTY LCUT SLPE 0: 6, 1: 18 (db/oct) RTTY HCUT FREQ 00: FF, 01: 700, ~, 67: 4000 Hz (50Hz/step) RTTY HCUT SLPE 0: 6, 1: 18 (db/oct) PLARITY-R 0: NR, 1: REV PLARITY-T 0: NR, 1: REV RTTY UT 0: VF-A, 1: VF-B RTTY UT LEVEL 000 ~ RTTY SHIFT 0: 170, 1: 200, 2: 425, 3: 850 (Hz) RTTY TNE 0: 1275, 1: 2125 (Hz) SSB LCUT FREQ 00: FF, 01: 100 ~ 19: 1000Hz (50Hz/step) SSB LCUT SLPE 0: 6, 1: 18 (db/oct) SSB HCUT FREQ 00: FF, 01: 700 ~ 67: 4000 Hz (50Hz/step) SSB HCUT SLPE 0: 6 1: 18 (db/oct) SSB MIC SELECT 0: FRNT, 1: DATA, 2: PC SSB-T-BPF 0: , 1: , 2: , 3: , 4: (Hz), 5: 3000WB LSB R-CARRIER -200Hz~0~+200 Hz (10Hz/step) (P2 = -200 ~ +000 ~ +200) USB R-CARRIER -200Hz~0~+200 Hz (10Hz/step) (P2 = -200 ~ +000 ~ +200) AGC-SLPE 0: NRMAL, 1: SLPE HEADPHNE MI 0: SEPARATE, 1: CMBINE-1, 2: CMBINE IF UT 0: ENABLE, 1: DISABLE MAIN NB LEVEL 000 ~ MAIN NB WIDTH 000 ~ MAIN-CNTUR-LEVEL -40~0~20 (P2 = -40 ~ +00 ~ +20) MAIN-CNTUR-WIDTH 01 ~ IF-NTCH-WIDTH 0: NARRW, 1: WIDE MAIN-CW SHAPE 0: SFT, 1: SHARP MAIN-CW SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE MAIN-PSK SHAPE 0: SFT, 1: SHARP MAIN-PSK SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE MAIN-RTY SHAPE 0: SFT, 1: SHARP MAIN-RTY SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE MAIN-SSB SHAPE 0: SFT, 1: SHARP MAIN-SSB SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE SUB-CW SHAPE 0: SFT, 1: SHARP SUB-CW SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE SUB-PSK SHAPE 0: SFT, 1: SHARP SUB-PSK SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE SUB-RTY SHAPE 0: SFT, 1: SHARP SUB-RTY SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE SUB-SSB SHAPE 0: SFT, 1: SHARP SUB-SSB SLPE 0: STEEP, 1: MEDIUM, 2: GENTLE FI 1.8MHz 1.800MHz ~ 1.999MHz 1kHz /step (P2 = ~ 01999) FI 3.5MHz 3.500MHz ~ 3.999MHz 1kHz /step (P2 = ~ 03999) FI 5.0MHz 5.250MHz ~ 5.499MHz 1kHz /step (P2 = ~ 05499) FI 7.0MHz 7.000MHz ~ 7.299MHz 1kHz /step (P2 = ~ 07299) FI 10MHz MHz ~ MHz 1kHz /step (P2 = ~ 10149) FI 14MHz MHz ~ MHz 1kHz /step (P2 = ~ 14349) FI 18MHz MHz ~ MHz 1kHz /step (P2 = ~ 18199) FI 21MHz MHz ~ MHz 1kHz /step (P2 = ~ 21449) FI 24MHz MHz ~ MHz 1kHz /step (P2 = ~ 24989) FI 28MHz MHz ~ MHz 1kHz /step (P2 = ~ 29699) FI 50MHz MHz ~ MHz 1kHz /step (P2 = ~ 53999) DIAL STEP 0: 1, 1: 5Hz, 2: 10Hz DIAL CW FINE 0: DISABLE, 1: ENABLE UP/DWN STEP 0: 1MHz, 1: 100kHz AM CH STEP 0: 2.5, 1: 5, 2: 9, 3: 10, 4: 12.5kHz FM CH STEP 0: 5, 1: 6.25, 2: 10, 3: 12.5, 4: 20kHz, 5: 25kHz AM DIAL LCK 0: DISABLE, 1: ENABLE FM DIAL LCK 0: DISABLE, 1: ENABLE FM DIAL STEP 0: 10, 1: 100Hz MY BAND ~ (see Page 9) PRMTRC EQ1 FREQ 00: FF, 01: 100, 02: 200, 03: 300, 04: 400, 05: 500, 06: 600, 07: 700 (Hz) PRMTRC EQ1 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) PRMTRC EQ1 BWTH 01~ PRMTRC EQ2 FREQ 00: FF, 01: 700, 02: 800, 03: 900, 04: 1000, 05: 1100, 06: 1200, 07: 1300, 08: 1400, 09: 1500 (Hz) PRMTRC EQ2 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) PRMTRC EQ2 BWTH 01~ PRMTRC EQ3 FREQ 00: FF,01: 1500, 02: 1600, 03: 1700,04: 1800, 05: 1900, 06: 2000, 07: 2100, 08: 2200, 09: : 2400, 11: 2500, 12: 2600, 13: 2700, 14: 2800, 15: 2900, 16: 3000, 17: 3100, 18: 3200 (Hz) FTD5000 SERIES CAT PERATIN REFERENCE Page 8

10 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES TABLE 3 FUNCTIN P2 BYTE 158 PRMTRC EQ3 LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) PRMTRC EQ3 BWTH 01~ P-PRMTRC EQ1-FREQ 00: FF, 01: 100, 02: 200, 03: 300, 04: 400, 05: 500, 06: 600, 07: 700 (Hz) P-PRMTRC EQ1-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) P-PRMTRC EQ1-BWTH 01~ P-PRMTRC EQ2-FREQ 00: FF, 01: 700, 02: 800, 03: 900, 04: 1000, 05: 1100, 06: 1200, 07: 1300, 08: 1400, 09: 1500 (Hz) P-PRMTRC EQ2-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) P-PRMTRC EQ2-BWTH 01~ P-PRMTRC EQ3-FREQ 00: FF, 01: 1500, 02: 1600, 03: 1700,04: 1800, 05: 1900, 06: 2000, 07: 2100, 08: 2200, 09: : 2400, 11: 2500, 12: 2600, 13: 2700, 14: 2800, 15: 2900, 16: 3000, 17: 3100, 18: 3200 (Hz) 167 P-PRMTRC EQ3-LEVEL -10~0~+10 (P2 = -10 ~ +00 ~ +10) P-PRMTRC EQ3-BWTH 01~ FINAL BIAS A(1~100%) (P2 = 0001~0100: A(1~100%)) T MA PWER 0: 10(20), 1: 20(50), 2: 50(100), 3: 100(200) (200W type) T PWR CNTRL 0: ALL MDE, 1: CARRIER ET AMP T-GND 0: DISABLE, 1: ENABLE ET AMP TUNING PWR 0: 10(20), 1: 20(50), 2: 50(100), 3: 100(200) (200W type) V SELECT 0: MIC, 1: DATA ANTI V GAIN 000~ EMERGENCY FREQ T 0: DISABLE, 1: ENABLE 1 Menu Item 017 LEVEL INDICATR Command P2 13-Byte Details 1 Byte Byte PRCE MIC GAIN RF PWR V DELAY CW DELAY CW SPEED CW PITCH Menu Item 150 MY BAND SELECT Command P2 14-Byte Details 1 Byte Byte TRANSVERTER 50M TRANSVERTER 28M TRANSVERTER 14M GENERAL 50 MHz 28 MHz 24.5 MHz 21 MHz 18 MHz 14 MHz 10 MHz 7 MHz 3.5 MHz 1.8 MHz Page 9 FTD5000 SERIES CAT PERATIN REFERENCE

11 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES FA FREQUENCY VF-A F A ; F A ; F A ; FB FREQUENCY VF-B F B ; F B ; F B ; (Hz) (Hz) FR FUNCTIN R F R ; F R ; F R ; 0: Main (VF-A) Band Receiver: R, Sub (VF-B) Band Receiver: FF 1: Main (VF-A) Band Receiver: Mute, Sub (VF-B) Band Receiver: FF 2: Main (VF-A) Band Receiver: R, Sub (VF-B) Band Receiver: R 3: Main (VF-A) Band Receiver: Mute, Sub (VF-B) Band Receiver: R FS FAST STEP F S ; F S ; F S ; 0: VF A FF (SET nly) 1: VF A N (SET nly) 2: VF B FF (SET nly) 3: VF B N (SET nly) 4: VF A FF, VF B FF 5: VF A N, VF B FF 6: VF A FF, VF B N 7: VF A N, VF B N FT FUNCTIN T F T ; F T ; F T P2 ; P2 0: T Band = Main (VF-A) Band Sub (VF-B) Band (Toggle) 1: T Band = Sub (VF-B) Band Main (VF-A) Band (Toggle) 2: T Band = Main (VF-A) Band 3: T Band = Sub (VF-B) Band 0: T Band = Main (VF-A) Band 1: T Band = Sub (VF-B) Band GT AGC FUNCTIN G T P2 ; G T ; G T P3 ; 0: Main (VF-A) Band 1: Sub (VF-B) Band P2 0: AGC FF 1: AGC FAST 2: AGC MID 3: AGC SLW 4: AGC AUT P3 0: AGC FF 1: AGC FAST 2: AGC MID 3: AGC SLW 4: AGC AUT-FAST 5: AGC AUT-MID 6: AGC AUT-SLW ID IDENTIFICATIN 0362: FTD5000 I D ; I D ; FTD5000 SERIES CAT PERATIN REFERENCE Page 10

12 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN IF INFRMATIN I F ; I F P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; CNTRL CMMAND TABLES (Memory Channel) P2 VF-A Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory 2: Memory Tune 3: Quick Memory Bank (QMB) 4: QMB-MT P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Page 5: CTCSS Tone Chart ) 00 ~ : Simplex 1: Plus Shift 2: Minus Shift IS IF-SHIFT I S -/+ P2 P2 P2 P2 ; I S ; I S -/+ P2 P2 P2 P2 ; P2 0:Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver ~ Hz KM KEYER MEMRY Set ~ 53 ** 1-5 : Keyer Memory Channel Number K M P2 P2 P2 P2 ~ P2 ; P2 Message Characters (up to 50 characters) When the message is complete, add the "" character at the end to signify the termination of the message. K M ; Answer ~ 53 ** ex. KM CQ ~ ; ( space) K M P2 P2 P2 P2 ~ P2 ; KP KEY PITCH K P ; K P ; K P ; 00 ~75: 300 Hz ~ 1050 Hz (10 Hz Step) KR KEYER K R ; K R ; K R ; 0: KEYER FF 1: KEYER N KS KEY SPEED K S ; K S ; K S ; (WPM) KY CW KEYING K Y ; 1: Keyer Memory 1 Playback 6: Message Keyer 1 Playback 2: Keyer Memory 2 Playback 7: Message Keyer 2 Playback 3: Keyer Memory 3 Playback 8: Message Keyer 3 Playback 4: Keyer Memory 4 Playback 9: Message Keyer 4 Playback 5: Keyer Memory 5 Playback A: Message Keyer 5 Playback LK LCK L K ; L K ; L K ; 0: VF A FF (SET nly) 1: VF A N (SET nly) 2: VF B FF (SET nly) 3: VF B N (SET nly) 4: VF A FF, VF B FF 5: VF A N, VF B FF 6: VF A FF, VF B N 7: VF A N, VF B N Page 11 FTD5000 SERIES CAT PERATIN REFERENCE

13 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES LM LAD MESSAGE L M P2 ; L M ; L M P2 ; 0: DVS P2 When =0 When =1 1: P. B 0: DVS (Recording Stop) 0: P.B (Recording Stop) 1: DVS (CH 1 Recording Start/Stop) 1: P.B (Recording Start) 2: DVS (CH 2 Recording Start/Stop) 3: DVS (CH 3 Recording Start/Stop) 4: DVS (CH 4 Recording Start/Stop) 5: DVS (CH 5 Recording Start/Stop) MA MEMRY CHANNEL T VF-A M A ; MC MEMRY CHANNEL M C ; M C ; M C ; : Memory Channel Number : Regular Memory Channel 100: L 101: U ~ 116: P9L 117: P9U MD PERATING MDE M D P2 ; M D ; M D P2 ; MG MIC GAIN M G ; M G ; M G ; MK MDE KEY M K ; ML MNITR LEVEL M L P2 P2 P2 ; M L ; M L P2 P2 P2 ; 0: Main (VF-A) Band 1: Sub (VF-B) Band P2 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U KEY 0: LSB 1: USB 2: CW 3: AM / FM 4: FM / FM 5: RTTY 6: PKT 0: MNI N/FF 1: MNI Level P2 When =0 000: MNI FF 001: MNI N When = MR MEMRY CHANNEL READ M R ; M R P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; Memory Channel Number P2 Memory Channel Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Page 5: CTCSS Tone Chart ) 00 ~ : Simplex 1: Plus Shift 2: Minus Shift FTD5000 SERIES CAT PERATIN REFERENCE Page 12

14 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES MS METER SW M S ; M S ; M S ; 0: CMP 1: ALC 2: P 3: SWR 4: ID 5: VDD MW MEMRY CHANNEL WRITE Memory Channel Number P2 Memory Channel Frequency (Hz) M W P2 P2 P2 P2 P2 P3 Clarifier Direction +: Plus Shift, --: Minus Shift Clarifier ffset: (Hz) P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: (Fixed) P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Page 5: CTCSS Tone Chart ) 00 ~ : Simplex 1: Plus Shift 2: Minus Shift M M SET M ; N ; N ; NA NARRW M A P2 ; N A ; N A P2 ; NB NISE BLANKER STATUS N B P2 ; N B ; N B P2 ; NL NISE BLANKER LEVEL N L P2 P2 P2 ; N L ; N L P2 P2 P2 ; NR NISE REDUCTIN N R P2 ; N R ; N R P2 ; 0: M FF 1: M N 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: FF 1: N 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: Noise Blanker FF 1: Noise Blanker N 2: Noise Blanker (Wide) N 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P : Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: Noise Reduction FF 1: Noise Reduction N I PPSITE BAND INFRMATIN I ; I P2 P2 P2 P2 P P2 P2 P2 P3 P3 P3 P3 P3 P4 P P6 P7 P8 P9 P9 0 ; Current Memory Channel P2 VF-B Frequency (Hz) P3 Clarifier Direction +: Plus Shift, --: Minus Shift Crarifier ffset: (Hz) P4 0: R CLAR FF 1: R CLAR N P5 0: T CLAR FF 1: T CLAR N P6 MDE 1: LSB 2: USB 3: CW 4: FM 5: AM 6: FSK (RTTY-LSB) 7: CW-R 8: PKT-L 9: FSK-R (RTTY-USB) A: PKT-FM B: FM-N C: PKT-U P7 0: VF 1: Memory P8 0: CTCSS FF 1: CTCSS ENC/DEC 2: CTCSS ENC P9: Tone Number (See Page 5: CTCSS Tone Chart ) 00 ~ : Simplex 1: Plus Shift 2: Minus Shift Page 13 FTD5000 SERIES CAT PERATIN REFERENCE

15 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES S FFSET (REPEATER SHIFT) S P2 ; S ; S P2 ; PA PRE-AMP (IP) P A P2 ; P A ; P A P2 ; PB PLAY BACK P B P2 ; P B ; P B P2 ; PC PWER CNTRL P C ; P C ; P C ; PL SPEECH PRCESSR LEVEL P L ; P L ; P L ; PR SPEECH PRCESSR P R ; P R ; P R ; PS PWER SWITCH P S ; P S ; P S ; 0: Main (VF-A) Band 1: Sub (VF-B) Band P2 0: Simplex 1: Plus Shift 2: Minus Shift : FM mode only 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: IP 1 1: AMP 1 2: AMP 2 3: IP 2 0: DVS P2 When =0 When =1 1: P.B 0: DVS (Recording Stop) 0: P.B (Playback Stop) 1: DVS (CH 1 Playback Start) 1: P.B (Playback Start) 2: DVS (CH 2 Playback Start) 3: DVS (CH 3 Playback Start) 4: DVS (CH 4 Playback Start) 5: DVS (CH 5 Playback Start) : Speech Processor FF 1: Speech Processor N 2: Microphone Equalizer N 0: PWER FF 1: PWER N (Send the PS1; command twice every one second.) QI QMB STRE Q I ; QR QMB RECALL Q R ; FTD5000 SERIES CAT PERATIN REFERENCE Page 14

16 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN QS QUICK SPLIT Q S ; CNTRL CMMAND TABLES RA RF ATTENUATR R A P2 ; R A ; R A P2 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: FF 1: 6 db 2: 12 db 3: 18 db RC CLAR CLEAR R C ; RD CLAR MINUS FFSET R D ; (Hz) RF RFING FILTER R F P2 ; R F ; R F P3 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: AUT P3 1: 15 khz 2: 6 khz 3: 3 khz 4: 600 Hz (Main) 5: 300 Hz (Main) 1: 15 khz 8: 300 Hz (Main) 2: 6 khz 9: AUT Hz (Main) 3: 3 khz A: AUT Hz (Main) 4: AUT - 15 khz 5: AUT - 6kHz 6: AUT - 3 khz 7: 600 Hz (Main) RG RF GAIN R G P2 P2 P2 ; R G ; R G P2 P2 P2 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P RI RADI INFRMATIN R I ; R I P2 ; 0: Hi-SWR 1: MIC-EQ 2: CLASS-A 3: REC 4: PLAY 5: MAIN T 6: SUB T 7: MAIN R 8: SUB R P2 0: FF 1: N RL NISE REDUCTIN LEVEL R L P2 P2 ; R L ; R L P2 P2 ; RM READ METER R M ; R M P2 P2 P2 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P : Depends of the front panel s METER knob 1: S Meter (Main) 5: P Meter 2: S Meter (Sub) 6: SWR Meter 3: CMP Meter 7: ID Meter 4: ALC Meter 8: VDD Meter P Page 15 FTD5000 SERIES CAT PERATIN REFERENCE

17 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN R RTATR R ; R ; R P2 P2 P2 P3 P3 P3 ; CNTRL CMMAND TABLES 0: FF 1: Counter Clockwise 2: Clockwise 3: SPEED 1 % DWN 4: SPEED 1 % UP P2 DIRECTIN (0-450) P3 SPEED (0-100 %) RS RADI STATUS R S ; R S ; RT CLAR R T ; R T ; R T ; 0: NRMAL MDE 1: MENU MDE 0: R Clarifier FF 1: R Clarifier N RU R CLARIFIER PLUS FFSET R U ; (Hz) SC SCAN S C ; S C ; S C ; 0: Scan FF 1: Scan N (Upward) 2: Scan N (Downward) SD CW BREAK-IN DELAY TIME S D ; S D ; S D ; (ms) SF SUB VF-B KNB FUNCTIN S F ; S F ; S F ; 00: BAND 01: - 02: GRP 03: MCH 04: - 05: - 06: - 07: S-DIAL 08: CLAR SH WIDTH 0: Main (VF-A) Band Receiver Read S H P2 P2 ; 1: Sub (VF-B) Band Receiver P2 00 [Default] SSB NARRW 01: : : : : 1100 S H ; 06: : [1500] SSB WIDE 07: : : : : 2100 S H P2 P2 ; 12: : [2400] 14: : : : : : : : : : : : 4000 CW NARRW 01: 50 02: : : : : : : : : [500] CW WIDE 10: : : : : : : [2400] RTTY NARRW 01: 50 02: : : : : [300] 07: : : : 500 RTTY WIDE 10: [500] 11: : : : : : 2400 PSK NARRW 01: 50 02: : : : : [300] 07: : : : 500 PSK WIDE 10: [500] 11: : : : : : 2400 FTD5000 SERIES CAT PERATIN REFERENCE Page 16

18 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES SM S-METER READING S M ; S M P2 P2 P2 ; SQ SQUELCLH LEVEL S Q P2 P2 P2 ; S Q ; S Q P2 P2 P2 ; 0: Main (VF-A) Band S-meter 1: Sub (VF-B) Band S-meter P : Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P SV SWAP VF S V ; TS TW T S ; T S ; T S ; T T SET T ; T ; T ; UL PLL UNLCK STATUS U L ; U L ; 0: TW FF 1: TW N 0: RADI T FF CAT T FF 1: RADI T FF CAT T N 2: RADI T N CAT T FF (Answer) 0: PLL Lock 1: PLL Unlock UP MIC UP U P ; VD V DELAY TIME V D ; V D ; V D ; ms (20 ms multiples) VF VRF FILTER V F P2 P3 P4 ; V F ; V F P2 P5 P5 P5 P6 ; 0: Main (VF-A) Band Receiver 1: Sub (VF-B) Band Receiver P2 0: FF 1: N 2: Default set P3 +: Plus Shift : Minus Shift P4 0-9 (Step) P P6 0: VRF 1: μtune Page 17 FTD5000 SERIES CAT PERATIN REFERENCE

19 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN CNTRL CMMAND TABLES VG V GAIN V G ; V G ; V G ; VM VF-A T MEMRY CHANNEL V M ; VS VF SELECT V S ; V S ; V S ; V V STATUS V ; V ; V ; T T CLAR Set T ; T ; T ; 0: VF-A 1: VF-B 0: V FF 1: V N 0: T CLAR FF 1: T CLAR N FTD5000 SERIES CAT PERATIN REFERENCE Page 18

20 CAT (CMPUTER AIDED TRANSCEIVER) PERATIN Copyright 2010 VERTE STANDARD C., LTD. All rights reserved No portion of this manual may be reproduced without the permission of VERTE STANDARD C., LTD. E H H FTD5000 SERIES CAT PERATIN REFERENCE