FT-891 YAESU MUSEN CO., LTD.

Transcription

1 FT- CAT Operation Reference Book YAESU MUSEN CO., LTD.

2 Overview The CAT (Computer Aided Transceiver) System in the FT- transceiver provides control of frequency, VFO, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated with single mouse clicks, or keystroke operations on the computer keyboard. Using the USB Cable (Refer to figure ) Note: A USB driver is required for remote control from a computer. Download the driver from the Yaesu website ( The FT- transceiver has a built-in USB to Dual UART Bridge, allowing direct connection from the rear-panel USB jack to the USB jack of your computer without the need of any external boxes. You will need a USB cable to connect to the USB jack on your computer. YAESU MUSEN does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs for your operating needs and utilize the full operating potential of this system. Connection Personal Computer FT- USB USB Commercially available USB Cable Figure FT- CAT Operation Reference Book

3 Control Command A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: the VFO-A frequency to.0000 MHz. FA Command Parameter Terminator There are three commands for the FT- as shown below: command: a particular condition (to the FT-) command: s an answer (from the FT-) command: Transmits a condition (from the FT-) For example, note the following case of the FA command ( the VFO-A frequency): To set the VFO-A frequency to.0000 MHz, the following command is sent from the computer to the transceiver: FA00000 ( command) To read the VFO-A frequency, the following command is sent from the computer to the transceiver: FA ( command) When the command above has been sent, the following command is returned to the computer: FA00000 ( command) Alphabetical Commands A command consists of alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the PC Control Command Tables on the following pages. Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the Control Command List and the Control Command Tables to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when the correct parameter is IS0+000 (IF SHIFT): IS0000 Not enough parameters specified (No direction (+) given for the IF shift) IS0+00 Not enough digits (Only three frequency digits given) IS0_+_000 Unnecessary characters between parameters IS Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT-, the parameter digits should be filled using any character except the ASCII control codes (00 to Fh) and the terminator (). Terminator To signal the end of a command, it is necessary to use a semicolon (). The digit where this special character must appear differs depending on the command used. FT- CAT Operation Reference Book

4 Command Function Ans. AI AB VFO-A TO VFO-B O X X X AC ANTENNA TUNER CONTROL O O O O AG AF GAIN O O O O AI AUTO INFORMATION O O O X AM VFO-A TO MEMORY CHANNEL O X X X BA VFO-B TO VFO-A O X X X BC AUTO NOTCH O O O O BD BAND DOWN O X X X BI BREAK-IN O O O O BP MANUAL NOTCH O O O O BS BAND SELECT O X X X BU BAND UP O X X X BY BUSY X O O O CF CLAR O O O O CH CHANNEL UP/DOWN O X X X CN CTCSS/DCS NUMBER O O O O CO CONTOUR O O O O CS CW SPOT O O O O CT CTCSS O O O O DA DIMMER O O O X DN DOWN O X X X ED ENCORDER DOWN O X X X EK ENT KEY O X X X EU ENCORDER UP O X X X EX MENU O O O O FA FREQUENCY VFO-A O O O X FB FREQUENCY VFO-B O O O X FS FAST STEP O O O O GT AGC FUNCTION O O O O ID IDENTIFICATION X O O X IF INFORMATION X O O O IS IF-SHIFT O O O O KM KEYER MEMORY O O O X KP KEY PITCH O O O O KR KEYER O O O O KS KEY SPEED O O O O KY CW KEYING O X X X LK LOCK O O O O LM LOAD MESSAGE O O O X MA MEMORY CHANNEL TO VFO-A O X X X MC MEMORY CHANNEL O O O X MD MODE O O O O MG MIC GAIN O O O O ML MONITOR LEVEL O O O O MR MEMORY READ X O O X MS METER SW O O O O MT MEMORY WRITE & TAG O X X X MW MEMORY WRITE O X X X MX MOX SET O O O O NA NARROW O O O O NB NOISE BLANKER O O O O NL NOISE BLANKER LEVEL O O O O NR NOISE REDUCTION O O O O OI OPPOSITE BAND NFORMATION X O O O OS OFFSET (Repeater Shift) O O O O PA PRE-AMP (IPO) O O O O PB PLAY BACK O O O X PC POWER CONTROL O O O O PL SPEECH PROCESSOR LEVEL O O O O Command Function Ans. AI PR SPEECH PROCESSOR O O O O PS POWER SWITCH O O O X QI QMB STORE O X X X QR QMB RECALL O X X X QS QUICK SPLIT O X X X RA RF ATTENUATOR O O O O RC CLAR CLEAR O X X X RD CLAR DOWN O X X X RG RF GAIN O O O O RI RADIO INFORMATION X O O O RL NOISE REDUCTION LEVEL O O O O RM READ METER X O O O RS RADIO STATUS X O O O RU CLAR UP O X X X SC SCAN O O O O SD SEMI BREAK-IN DELAY TIME O O O O SH WIDTH O O O O SM S METER X O O X SQ SQUELCH LEVEL O O O O ST SPLIT O O O O SV SWAP VFO O X X X TS TXW O O O O TX TX SET O O O O UL UNLOCK X O O O UP UP O X X X VD VOX DELAY TIME O O O O VG VOX GAIN O O O O VM [V/M] KEY FUNCTION O X X X VX VOX O O O O ZI ZERO IN O X X X FT- CAT Operation Reference Book

5 AB VFO-A TO VFO-B A B AC ANTENNA TUNER CONTROL 0: (Fixed) P 0: Tuner OFF A C P P P 0: (Fixed) : Tuner ON : Tuning Start A C A C P P AG AF GAIN 0: (Fixed) A G P P P P A G A G P P P AI AUTO INFORMATION 0: Auto Information OFF A I : Auto Information ON A I This parameter is set to 0 (OFF) automatically when the transceiver is turned OFF. A I AM VFO-A TO MEMORY CHANNEL A M BA VFO-B TO VFO-A B A BC AUTO NOTCH 0: (Fixed) B C P P 0: Auto Notch OFF : Auto Notch ON B C B C P BD BAND DOWN 0: (Fixed) B D FT- CAT Operation Reference Book

6 BI BREAK-IN 0: Break-in OFF B I : Break-in ON B I B I BP MANUAL NOTCH 0: (Fixed) P P=0 B P P P P P P 0: Manual NOTCH ON/OFF 000: OFF B P P 0 0 : Manual NOTCH LEVEL 00: ON P= 00-0 (NOTCH Frequency : x 0 Hz ) B P P P P P BS BAND SELECT 00:. MHz 0: MHz : MW B S 0:. MHz 0: MHz 0: - 0:. MHz 0: MHz 0: MHz 0: 0 MHz 0: 0 MHz 0: MHz : GEN BU BAND UP 0: (Fixed) B U BY BUSY 0: RX BUSY OFF : RX BUSY ON P 0: (Fixed) B Y B Y P CF CLAR 0: (Fixed) C F P P P 0: CLAR OFF : CLAR ON P 0: (Fixed) C F C F P P CH CHANNEL UP/DOWN 0: Memory Channel UP C H : Memory Channel DOWN CN CTCSS TONE FREQUENCY 0: (Fixed) C C N N P P P P P 0 P 0: CTCSS : DCS P P= : Tone Frequency Number (See Table, page ) P= 000-0: DCS Code Number (See Table, page) C N P P P P FT- CAT Operation Reference Book

7 CO CONTOUR 0: (Fixed) P P=0 0000: CONTOUR OFF C O P P P P P P 0: CONTOUR ON/OFF 000: CONTOUR ON : CONTOUR FREQ P= : APF ON/OFF (CONTOUR Frequency:0-00 Hz) C O P : APF FREQ P= 0000: APF OFF C O P P P P P 0 000: APF ON P= (APF Frequency: -0-0 Hz ) CS CW SPOT 0: OFF C S : ON C S C S CT CTCSS 0: (Fixed) C C T T P 0 P 0: CTCSS OFF : CTCSS ENC/DEC ON : CTCSS ENC ON : DCS ON C T P Table (CTCSS Tone Chart) Hz 00. Hz 0.0 Hz 0. Hz 0. Hz 0. Hz 00. Hz 00. Hz 0. Hz 0. Hz 0. Hz 0. Hz 00. Hz 0. Hz 00. Hz 0. Hz 0. Hz 0. Hz 00. Hz Hz 0. Hz 00. Hz 0. Hz 0 0. Hz 00.0 Hz 0 0. Hz 0. Hz 0. Hz Hz 0. Hz 00. Hz 0 0. Hz 0. Hz 0. Hz 0 0. Hz Hz 0 0. Hz 0. Hz 0. Hz 0 0. Hz Hz 0. Hz 0. Hz 0. Hz 0. Hz Hz 0. Hz 0. Hz 0. Hz 0. Hz - - Table (DCS Code Chart) DA DIMMER 0 - : LCD Contrast Level D A P P P P P P P 0 - : Dimmer Backligt Level 0 P 00 - : Dimmer LCD Level P 00 - : Dimmer TX/BUSY Level D A D A P P P P P P 0 FT- CAT Operation Reference Book

8 DN MIC DWN D N ED ENCORDER DOWN 0: MAIN ENCORDER E D P P : MULTI FUNCTION KNOB P 0 - : Steps EK ENT KEY E K EU ENCORDER UP 0: MAIN ENCORDER E U P P : MULTI FUNCTION KNOB P 0 - : Steps EX MENU ~ n- n : 00-0 (MENU Number) E X P ~ P P : Parameter (See Table below) E X ~ n- n E X P ~ P Function P Digits 00 AGC FAST DELAY (msec) (P= , 0 msec/step) 00 AGC MID DELAY (msec) (P= , 0 msec/step) 00 AGC SLOW DELAY (msec) (P= , 0 msec/step) 00 LCD CONTRAST 0-00 DIMMER BACKLIT 0-00 DIMMER LCD 0-00 DIMMER TX/BUSY 0-00 PEAK HOLD 0: OFF : 0. sec :.0 sec :.0 sec 00 ZIN LED 0: DISABLE : ENABLE 00 POP-UP MENU 0: UPPER : LOWER 00 DVS RX OUT LVL (P= ) 00 DVS TX OUT LVL (P= ) 00 KEYER TYPE 0: OFF : BUG : ELEKEY-A : ELEKEY-B : ELEKEY-Y : ACS 00 KEYER DOT/DASH 0: NOR : REV 00 CW WEIGHT. -. (P= - ) 00 BEACON INTERVAL OFF/ - 0 sec (P= 000-0, 000: OFF) 00 NUMBER STYLE 0: 0 : AUNO : AUNT : ANO : ANT : NO : NT 00 CONTEST NUMBER CW MEMORY 0: TEXT : MESSAGE 00 CW MEMORY 0: TEXT : MESSAGE 00 CW MEMORY 0: TEXT : MESSAGE 00 CW MEMORY 0: TEXT : MESSAGE 0 CW MEMORY 0: TEXT : MESSAGE 00 NB WIDTH 0: msec : msec : 0 msec 00 NB REJECTION 0: 0 db : 0 db : 0 db 00 NB LEVEL 0-0 (P= 00-0) 00 BEEP LEVEL 0-00 (P= ) 00 RF/SQL VR 0: RF : SQL 00 CAT RATE 0: 00 bps : 00 bps : 00 bps : 00 bps 00 CAT TOT 0: 0 msec : 00 msec : 000 msec : 000 msec 00 CAT RTS 0: DISABLE : ENABLE FT- CAT Operation Reference Book

9 Function P Digits 00 MEM GROUP 0: DISABLE : ENABLE 00 FM SETTING 0: DISABLE : ENABLE 0 REC SETTING 0: DISABLE : ENABLE 0 ATAS SETTING 0: DISABLE : ENABLE 0 QUICK SPL FREQ -0 khz (or -00) - +0 khz (P= or ) 0 TX TOT 00-0 min (P= 00-0, 00: OFF) 0 MIC SCAN 0: DISABLE : ENABLE 0 MIC SCAN RESUME 0: PAUSE : TIME 0 REF FREQ ADJ (or -00) - + (P= or ) 0 CLAR SELECT 0: RX : TX : TRX 0 APO 0: OFF : h : h : h : h : h : 0 h : h 00 FAN CONTROL 0: NORMAL : CONTEST 00 AM LCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 AM LCUT SLOPE 0: db/oct : db/oct 00 AM HCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 AM HCUT SLOPE 0: db/oct : db/oct 00 AM MIC SELECT 0: MIC : REAR 00 AM OUT LEVEL 0-00 (P= ) 00 AM PTT SELECT 0: DAKY : RTS : DTR 00 CW LCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 CW LCUT SLOPE 0: db/oct : db/oct 00 CW HCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 CW HCUT SLOPE 0: db/oct : db/oct 00 CW OUT LEVEL 0-00 (P= ) 00 CW AUTO MODE 0: OFF : 0M : ON 00 CW BFO 0: USB : LSB : AUTO 00 CW BK-IN TYPE 0: SEMI : FULL 00 CW BK-IN DELAY msec (P= ) (0 msec/step) 00 CW WAVE SHAPE : msec : msec 0 CW FREQ DISPLAY 0: FREQ : PITCH 0 PC KEYING 0: OFF : DAKY : RTS : DTR 0 QSK DELAY TIME 0: msec : 0 msec : msec : 0 msec 00 DATA MODE 0: PSK : OTHERS 00 PSK TONE 0: 000 Hz : 00 Hz : 000 Hz 00 OTHER DISP -000 Hz Hz (P= or ) (0 Hz/steps) 00 OTHER SHIFT -000 Hz Hz (P= or ) (0 Hz/steps) 00 DATA LCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 DATA LCUT SLOPE 0: db/oct : db/oct 00 DATA HCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 DATA HCUT SLOPE 0: db/oct : db/oct 00 DATA IN SELECT 0: MIC : REAR 00 DATA PTT SELECT 0: DAKY : RTS : DTR 0 DATA OUT LEVEL 0-00 (P= ) 0 DATA BFO 0: USB : LSB 00 FM MIC SELECT 0: MIC : REAR 00 FM OUT LEVEL 0-00 (P= ) 00 PKT PTT SELECT 0: DAKY : RTS : DTR 00 RPT SHIFT MHz khz (P= ) (0 khz/step) 00 RPT SHIFT 0MHz khz (P= ) (0 khz/step) 00 DCS POLARITY 0: Tn-Rn : Tn-Riv : Tiv-Rn : Tiv-Riv 00 RTTY LCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 RTTY LCUT SLOPE 0: db/oct : db/oct 00 RTTY HCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 00 RTTY HCUT SLOPE 0: db/oct : db/oct 00 RTTY SHIFT PORT 0: SHIFT : DTR : RTS 00 RTTY POLARITY-R 0: NOR : REV 00 RTTY POLARITY-T 0: NOR : REV 00 RTTY OUT LEVEL 0-00 (P= ) 00 RTTY SHIFT FREQ 0: 0 Hz : 00 Hz : Hz : 0 Hz 00 RTTY MARK FREQ 0: Hz : Hz 0 RTTY BFO 0: USB : LSB 0 SSB LCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 0 SSB LCUT SLOPE 0: db/oct : db/oct 0 SSB HCUT FREQ 00: OFF 0: 00 Hz - : 000 Hz (0 Hz steps) 0 SSB HCUT SLOPE 0: db/oct : db/oct 0 SSB MIC SELECT 0: MIC : REAR 0 SSB OUT LEVEL 0-00 (P= ) 0 SSB BFO 0: USB : LSB : AUTO 0 SSB PTT SELECT 0: DAKY : RTS : DTR 0 SSB TX BPF 0: : : : : APF WIDTH 0: NARROW : MEDIUM : WIDE 0 CONTOUR LEVEL (P= or ) 0 CONTOUR WIDTH 0-0 IF NOTCH WIDTH 0: NARROW : WIDE 0 SCP START CYCLE 0: OFF : sec : sec : 0 sec 0 SCP SPAN FREQ 0:. khz : khz : 0 khz : khz : 0 khz 0 QUICK DIAL 0: 0 khz : 00 khz : 00 khz 0 SSB DIAL STEP 0: Hz : Hz : 0 Hz 0 AM DIAL STEP 0: 0 Hz : 00 Hz 0 FM DIAL STEP 0: 0 Hz : 00 Hz 0 DIAL STEP 0: Hz : Hz : 0 Hz 0 AM CH STEP 0:. khz : khz : khz : 0 khz :. khz : khz FT- CAT Operation Reference Book

10 Function P Digits 0 FM CH STEP 0: khz :. khz : 0 khz :. khz : khz : 0 khz : khz 0 EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0 EQ LEVEL (P= or ) 0 EQ BWTH EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 000Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0 EQ LEVEL (P= or ) 0 EQ BWTH EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 000 Hz -: 00 Hz 0 EQ LEVEL (P= or ) 0 EQ BWTH P-EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz P-EQ LEVEL (P= or ) P-EQ BWTH 0-0 P-EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 000Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz P-EQ LEVEL (P= or ) P-EQ BWTH 0-0 P-EQ FREQ 00: OFF 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 00 Hz 0: 000 Hz -: 00 Hz P-EQ LEVEL (P= or ) P-EQ BWTH HF SSB PWR - 00 (P= 00-00) 0 HF AM PWR - 0 (P= 00-00) 0 HF PWR - 00 (P= 00-00) 0 0M SSB PWR - 00 (P= 00-00) 0 0M AM PWR - 0 (P= 00-00) 0 0M PWR - 00 (P= 00-00) 0 SSB MIC GAIN 0-00 (P= ) 0 AM MIC GAIN 0-00 (P= ) 0 FM MIC GAIN 0-00 (P= ) 0 DATA MIC GAIN 0-00 (P= ) SSB DATA GAIN 0-00 (P= ) AM DATA GAIN 0-00 (P= ) FM DATA GAIN 0-00 (P= ) DATA DATA GAIN 0-00 (P= ) TUNER SELECT 0: OFF : EXTERNAL : ATAS : LAMP VOX SELECT 0: MIC : DATA VOX GAIN 0-00 (P= ) VOX DELAY msec (P= ) (0 msec/step) ANTI VOX GAIN 0-00 (P= ) 0 DATA VOX GAIN 0-00 (P= ) DATA VOX DELAY msec (P= ) ANTI DVOX GAIN 0-00 (P= ) EMERGENCY FREQ 0: DISABLE : ENABLE 0 RESET 0: ALL : DATA : FUNC 0 MAIN VERSION (V0- = 0) 0 DSP VERSION (V0- = 0) 0 LCD VERSION (V0- = 0) FA FREQUENCY VFO-A (Hz) F A 0 F A F A 0 FB FREQUENCY VFO-B (Hz) F B 0 F B F B 0 FT- CAT Operation Reference Book

11 FS FAST STEP 0: VFO-A FAST Key OFF F S : VFO-A FAST Key ON F S F S GT AGC FUNCTION 0: (Fixed) P 0: AGC OFF G T P P 0: AGC OFF : AGC FAST : AGC FAST : AGC MID : AGC MID : AGC SLOW G T : AGC SLOW : AGC AUTO-FAST G T P 0 : AGC AUTO : AGC AUTO-MID : AGC AUTO-SLOW ID IDENTIFICATION 00: FT- I D I D IF INFORMATION I F (Regular Memory Channel) L - PU (PMS) 0-0 ( MHz, U.S. and U.K. version only) EMG (Emergency) P VFO-A Frequency (Hz) P Clarifier Direction +: Plus Shift, -: Minus Shift Clarifier Offset: (Hz) I F P P P P P P 0: CLAR OFF : CLAR ON 0 P 0: (Fixed) P MODE : SSB (SSB BFO) : SSB (SSB BFO) : CW : FM : AM P P P P +/- P P P P P : RTTY (RTTY BFO) : CW (CW BFO) : DATA (DATA BFO) 0 : RTTY (RTTY BFO) A: - B: FM-N C: DATA (DATA BFO) P P P P P P 0 D: AM-N P 0: VFO : Memory : Memory Tune : - : - : PMS P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift IS IF-SHIFT 0:(Fixed) I I S S P -/+ P P P P 0 P 0: OFF : ON P 0 ~ 00 Hz (0 Hz steps) I S P -/+ P P P P KM KEYER MEMORY ~ n - : Keyer Memory Channel Number K M P P P P ~ P P Message Characters (up to 0 characters) K M ~ n K M P P P P ~ P KP KEY PITCH 00: 00 Hz - : 00 Hz (0Hz steps) K P K P K P 0 FT- CAT Operation Reference Book

12 KR KEYER 0: KEYER OFF K R : KEYER ON K R K R KS KEY SPEED (WPM) K S K S K S KY CW KEYING : Keyer Memory Playback : Message Keyer Playback K Y : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback : Message Keyer Playback : Keyer Memory Playback A: Message Keyer Playback LK LOCK 0: VFO DIAL Lock OFF L K : VFO DIAL Lock ON L K L K LM LOAD MESSAGE 0: DVS P 0: DVS (Recording Stop) L L M M P 0 0 : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) : DVS (CH Recording Start/Stop) L M P MA MEMORY CHANNEL TO VFO-A M A MC MEMORY CHANNEL 00-0: Regular Memory Channel M C L - PU (PMS) M C M C MD OPERATING MODE 0: MAIN RX M D P P MODE : SSB (SSB BFO) : SSB (SSB BFO) : CW : FM : AM : RTTY (RTTY BFO) : CW (CW BFO) : DATA (DATA BFO) : RTTY (RTTY BFO) A: - B: FM-N C: DATA (DATA BFO) M D D: AM-N M D P FT- CAT Operation Reference Book

13 MG MIC GAIN M G M G M G ML MONITOR LEVEL 0: MONI ON/OFF M L P P P : MONI Level P =0 000: MONI OFF M L 00: MONI ON = M L P P P MR MEMORY CHANNEL READ P0/ 00-0 (Regular Memory Channel) L - PU (PMS) 0-0 ( MHz, U.S. and U.K. version only) EMG (Emergency) M R P0 P0 P0 P VFO-A Frequency (Hz) P Clarifier Direction +: Plus Shift, -: Minus Shift Clarifier Offset: (Hz) M R P P P P P P 0: CLAR OFF : CLAR ON 0 P 0: (Fixed) P P P P +/- P P P P P P MODE :LSB : USB : CW : FM : AM : RTTY-LSB : CW-R 0 : DATA-LSB : RTTY-USB A: - B: FM-N C: DATA-USB D: AM-N P P P P P P 0 P 0: VFO : Memory P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift MS METER SW 0: COMP M S : ALC : PO M S : SWR : ID M S MT MEMORY WRITE & TAG 00-0 (Regular Memory Channel) M T P P P P P L - PU (PMS) P Frequency (Hz) 0 P Clarifier Direction +: Plus Shift, -: Minus Shift P P P P +/- P P P P P Clarifier Offset: (Hz) 0 P 0: CLAR OFF : CLAR ON P P P P P P 0 P 0: (Fixed) P MODE : LSB : USB : CW : FM : AM : RTTY-LSB : CW-R 0 : DATA-LSB : RTTY-USB A: - B: FM-N C: DATA-USB D: AM-N P 0: (Fixed) P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift M T P0 P0 P0 0: TAG OFF : TAG ON TAG Characters (up to characters) (ASCII) M T P P P P P 0 P P P P +/- P P P P P 0 P P P P P P 0 0 FT- CAT Operation Reference Book

14 MW MEMORY CHANNEL WRITE 00-0 (Regular Memory Channel) M W P P P P P L - PU (PMS) P Frequency (Hz) 0 P Clarifier Direction +: Plus Shift, -: Minus Shift P P P P +/- P P P P P Clarifier Offset: (Hz) 0 P 0: CLAR OFF : CLAR ON P P P P P P 0 P 0: (Fixed) P MODE : LSB : USB : CW : FM : AM : RTTY-LSB : CW-R : DATA-LSB : RTTY-USB A: - B: FM-N C: DATA-USB D: AM-N P 0: (Fixed) P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift MX MOX SET 0: MOX OFF M X : MOX ON M X M X NA NARROW 0: (Fixed) N A P P 0: OFF : ON N A N A P NB NOISE BLANKER STATUS 0: (Fixed) N B P P 0: Noise Blanker OFF : Noise Blanker ON N B N B P NL NOISE BLANKER LEVEL 0: (Fixed) N L P P P P N L N L P P P NR NOISE REDUCTION 0: (Fixed) N R P P 0: Noise Reduction OFF : Noise Reduction ON N R N R P FT- CAT Operation Reference Book

15 OI OPPOSITE BAND INFORMATION 00-0 (Regular Memory Channel) L - PU (PMS) 0-0 ( MHz, U.S. and U.K. version only) EMG (Emergency) O I P VFO-B Frequency (Hz) P Clarifier Direction +: Plus Shift, -: Minus Shift O I P P P P P Clarifier Offset: (Hz) P 0: CLAR OFF : CLAR ON 0 P 0: (Fixed) P P P P +/- P P P P P P MODE : SSB (SSB BFO) : SSB (SSB BFO) : CW : FM : AM 0 : RTTY (RTTY BFO) : CW (CW BFO) : DATA (DATA BFO) P P P P P P 0 : RTTY (RTTY BFO) A: - B: FM-N C: DATA (DATA BFO) D: AM-N P 0: VFO : Memory : Memory Tune : Quick Memory Bank (QMB) : QMB-MT : PMS : HOME P 0: CTCSS OFF : CTCSS ENC/DEC : CTCSS ENC P 00: (Fixed) 0 0: Simplex : Plus Shift : Minus Shift OS OFFSET (REPEATER SHIFT) 0: (Fixed) O O S S P 0 P 0: Simplex : Plus Shift : Minus Shift *: This command can be activated only with an FM mode. O S P PA PRE-AMP (IPO) 0:(Fixed) P A P P 0: IPO : AMP P A P A P PB PLAY BACK 0: DVS P 0: DVS (Playback Stop) P P B B P 0 0 : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) : DVS (CH Playback Start) P B P PC POWER CONTROL P C P C P C PL SPEECH PROCESSOR LEVEL P L P L P L PR SPEECH PROCESSOR 0: Speech Processor P P R R P 0 : Parametric Microphone Equalizer P 0: OFF : ON P R P FT- CAT Operation Reference Book

16 PS POWER SWITCH 0: POWER OFF P S 0 : POWER ON P S This command requires dummy data be initially sent. Then after one second and before two seconds the command is sent. P S QI QMB STORE Q I QR QMB RECALL Q R QS QUICK SPLIT Q S RA RF ATTENUATOR 0: (Fixed) R A P P 0: OFF : ON R A R A P RC CLAR CLEAR R C RD CLAR DOWN (Hz) R D RG RF GAIN 0: (Fixed) R G P P P P R G R G P P P FT- CAT Operation Reference Book

17 RI RADIO INFORMATION 0: Hi-SWR : REC : PLAY A: TX LED B: RX LED R I 0 P 0: OFF : ON R I P RL NOISE REDUCTION LEVEL 0: (Fixed) R L P P P 0 - R L R L P P RM READ METER 0: Depends on the front panel METER : ALC : S : PO : Depends on the front panel METER : SWR R M 0 (PO / COMP / ALC / SWR / ID) : ID : COMP P 0 - R M P P P RS RADIO STATUS 0: NORMAL MODE : MENU MODE R S R S RU RX CLARIFIER PLUS OFFSET (Hz) R U SC SCAN 0: Scan OFF S C : Scan ON (UP ward) : Scan ON (DOWN ward) S C S C SD CW BREAK-IN DELAY TIME msec S D S D S D SH WIDTH 0: (Fixed) S H P P P P 0: OFF : ON P 00 (See Table below) S H S H P P P FT- CAT Operation Reference Book

18 Command Bandwidth P SSB (Narrow) SSB (Wide) CW (Narrow) CW (Wide) RTTY/PSK (Narrow) RTTY/PSK (Wide) 00 (Default) 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 00 Hz 0 00 Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz - 0 Hz - 0 Hz Hz - 00 Hz - 00 Hz Hz 00 Hz 0 Hz - 0 Hz Hz 00 Hz 00 Hz 00 Hz 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz Hz Hz - 00 Hz - 00 Hz - 00 Hz - 00 Hz Hz Hz - 00 Hz Hz Hz Hz SM S-METER READING 0: (Fixed) P S M S M P P P SQ SQUELCLH LEVEL 0: (Fixed) S Q P P P P S Q S Q P P P ST SPLIT 0: SPLIT OFF S Q : SPLIT ON : SPLIT ON + khz up S Q S Q SV SWAP VFO S V TS TX TXW 0: TXW OFF T S : TXW ON T S T S TX SET FT- CAT Operation Reference Book

19 0: RADIO TX OFF CAT TX OFF T X : RADIO TX OFF CAT TX ON : RADIO TX ON CAT TX OFF () T X T X UL PLL UNLOCK STATUS 0: PLL Lock : PLL Unlock U L U L UP UP U P VD VOX DELAY TIME msec (0 msec multiples) V D V D V D VG VOX GAIN V G V G V G VM VFO-A TO MEMORY CHANNEL V M VX VOX STATUS 0: VOX OFF V X : VOX ON V X V X ZI ZERO IN (CW AUTO ZERO IN Function) Z I FT- CAT Operation Reference Book

20 Copyright 0 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building -- Higashi-Shinagawa, Shinagawa-ku, Tokyo Japan YAESU USA Phyllis Drive, Cypress, CA 00, U.S.A. YAESU UK Unit, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO 0LB, U.K. 0-B