Table of Contents. CII Mid-Range Relays

Transcription

1 Table of Contents TD2 Series Time Delay Relays, per MIL-PRF-83726/28, /29, /30, & / Double-pole, Electrically Held, 5 mps and Less FC-205 Series Four-pole, Electrically Held, 5 mps and Less FC-405 Series Double-pole, Electrically Held, 15 mps and Less FC-210 Series FC-212 Series FC-215 Series Four-pole, Electrically Held, 15 mps and Less FC-410 Series FC-415 Series Single-pole, Electrically Held, 25 mps and Less FC-125 Series Three-pole, Electrically Held, 25 mps and Less FC-325 Series Three-pole, Electrically Held, 25 mps and Less, with uxiliary Contacts FCC-325 Series Single-Pole, Electrically Held, 50 mps or Less FC Single-Pole, Electrically Held, 50 mps and Less, Normally Closed, with uxiliary Contacts FC-150NC Single Pole, Electrically Held, 50 mps and Less, with uxiliary Contacts FCC Selection and pplication Guide Cross Reference - Socket to Relay Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 1

2 TD2 Series Time Delay Relay Product Facts n Qualified to: MIL-PRF-83726/28 MIL-PRF-83726/29 MIL-PRF-83726/30 MIL-PRF-83726/31 n Fixed delay on operate, fixed delay on release, adjustable delay on operate & adjustable delay on release n Meets or exceeds electrostatic discharge MIL-STD-1686 Class Non-Sensitive n Welded hermetically sealed enclosure occupies about 1 in 3 (16.4 cm 3 ) n 10, 2 form C (DPDT) output contacts TD2 series time delay relays are available for delay on operate or delay on release operation. Either can be supplied as fixed or resistor adjustable types. oth military and commercial versions are offered. These products consist of solid state timing circuits controlling our FC-210 series relays, providing 2 Form C (DPDT) output contacts rated 10 amps. The internal timing circuit uses an R/C controlled oscillator with a programmable digital pulse counter, gating a semiconductor switch to operate the relay. Timing is independent of whether the controlling voltage is a ramp or step function. For the adjustable models the user specifies a one decade range in seconds, within which the required delay will be set. This range is programmed internally at the time of manufacture. The required delay is obtained by calculating the oscillator timing resistor as follows and connecting it externally to terminals 1D - 3D as below. R EXT = [(T 1 / T 0 ) -1] 100K Ohms T 0 = Minimum time of selected decade in seconds. T1 = Required time delay. EXMPLE Selected Range = 3-30 sec Required Time = 15 sec R EXT = [(15/3) -1] 100K = 400K Timing ction and Terminal Wiring Delay On Operate: The time delay starts on the application of input voltage to X1. The timing circuit energizes the end of the time delay period. Delay On Release: The input voltage is continuous to X1. When the control voltage is applied to C1 the timing circuit and the relay are both energized. The time delay starts when the control voltage is shut off. INPUT VOLTGE / X2 OUTPUT RELY INPUT OFF DEENERGIZED 20-30VDC TIME DELY ENERGIZED INPUT VOLTGE / X2 CONTROL VOLTGE C1 / X2 CONTROL OFF OUTPUT RELY INPUT OFF DEENERGIZED 20-30VDC 20-30VDC ENERGIZED TIME DELY Fixed Model ( ) Fixed Model ( ) D D INPUT TD C CONTROL () INPUT TD C () () djustable Model EXT. RESISTOR 1/4 WTT MIN. djustable Model EXT. RESISTOR 1/4 WTT MIN. ( ) ( ) D D INPUT TD C CONTROL () INPUT TD C () () Terminal designations shown in the diagrams above are for reference only. They do not appear on the relay header. 5 2 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

3 TD2 Series Time Delay Relay (Continued) Specifications Timing Data Timing ction Time Delay, Fixed M83726/28, /29 and Commercial 28C, 29C Time Delay, djustable M83726/30, /31 and Commercial 30C, 31C Timing ccuracy (note 1) Recycle Time (note 2) Power Interrupts Input Data Input Voltage Duty Rating Delay on Operate or Delay on Release Select from 0.1 to 600 sec for Commercial Models Select from 0.1 to 500 sec for Mil-Spec Models Select one decade between 0.1 to 1.0 and 60 to 600 seconds ±10% of Nominal Value 50 ms, max., to next cycle. ccuracy is not affected by power interruptions up to 1 ms spaced at least 10ms apart. 28 Vdc nominal, range Vdc Continuous Input Current 110 mdc 25 C Control Voltage (applies only to Delay on Release type) Control Current Input Voltage Polarity Protection Output Data Contact Form Contact Material Contact Rating in mps (Continuous Duty) Vdc 15 mdc Max (applies only to delay on release types) The timer will be inoperative during, and undamaged by, reversal of the polarity of the input voltage. 2 Form C (DPDT) Silver Cadmium Oxide, Gold plated Type of Life (Min.) 115 Vac 115/200 Vac 3 phase Load Cycles 28 Vdc 400Hz 400 Hz. 60 Hz.* Resistive 100 x Inductive 20 x Motor 100 x Lamp 100 x * 60 Hz. loads are rated at 10 x 10 3 cycles. Overload Current 40 dc; 60, 400 Hz. Rupture Current 50 dc; 80, 400 Hz. Max. Contact Drop at 10 Initial 0.150V; fter Life 0.175V Electrical Data Electrostatic Discharge Withstand Voltage 16,000V Transients (note 3): Positive Transients 80V Self-generated Transients ±50V, Max. Spike Susceptibility ±600V, 10 µs, Max. Insulation Resistance (note 4) 1,000 megohms at 500Vdc, between each pin and case Dielectric Strength (note 4) 1,000Vrms at 60 Hz at sea level, between case and all pins connected together Environmental Data mbient Temperature Range, Operating -55 C to 125 C ltitude 80,000 feet maximum Shock Resistance 100 G s, 6 ms. Vibration Resistance, Sinusoidal Z & Y Enclosure: 30 G s, Hz.; X & W Enclosure: 20 G s, Hz. Mechanical Data pproximate Weight 2.5 oz. (71g) Max. 5 NOTES 1. The accuracy requirement applies to any combination of operating temperature and voltage. dd ±10ms for timing less than one second. 2. Recycle time to assure that the next timing cycle will be completed. Units can be recycled during timing and after time-out: Delay on operate models Power must be OFF the input at least 10 ms. Delay on release models Power must be ON the control terminal at least 10 ms. 3. Transient specifications are based on a maximum duty cycle of 1/ ll wired terminals must be connected together during this test. Dielectric withstanding voltage and insulation resistance are measured between all mutually insulated wired terminals and between all these terminals and case. 5. Inductive loads must be diode suppressed. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 3

4 TD2 Series Time Delay Relay (Continued) Outline Dimensions The standard terminal types and enclosures are illustrated below with dimensions expressed as inches ± and (millimeters ±0.25). Terminals ll terminals on (5.4) centers. "P" Socket Pins Gold Plated.270 (6.86).050 ±.005 (1.27 ± (3) Silicone Rubber Gasket "T" Circuit oard Pins Tin/Lead Plated.270 (6.86) "S" Solder Hooks.062 ±.001 Pin (1.57 ±.02) 14 places Dia. Pin ( ) 14 Plcs ±.020 (7.26) ±.51 X DI (2.03) Dia. Pin ( ) 14 Plcs Enclosures ll Enclosures have cupro-nickel cans bright acid tin/lead plated after assembly to terminal headers. "Z" "Y".150 typ. (3.8).625 (15.88).937 (23.80) 6 PLCS (35.46) (36.73).312 (7.92) (25.4) "X" (25.4) 6 PLCS typ. (3.8) (35.46) (36.73) Max. (43.64).625 (15.88).937 (23.80) (1.02) "W".312 (7.92) 6-32 UNC-2 3 Studs * (25.4) Max. (43.64) (25.78).687 (17.44).375 (9.52).047 (1.20).160 (4.06).687 (17.44) (1.02).156 (3.96).343 (8.71).160 (4.06) *Metric threads available. To specify use M in place of W 5 4 For factory-direct application assistance, phone or fax Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

5 TD2 Series Time Delay Relay (Continued) Part Numbering System Mil-Spec Types Commercial Types Typical Mil-Spec Part Number TD P Series: TD2 = Time delay relay with 2 pole, 10 output Mil-Spec Model: 28 = M83726/28 (Fixed, Delay on Operate) 29 = M83726/29 (Fixed, Delay on Release) 30 = M83726/30 (djustable, Delay on Operate) 31 = M83726/31 (djustable, Delay on Release) Time Delay Range (Within 0.1 to 500 seconds): For /28 and /29 types (fixed types), the delay is expressed in milliseconds in a four-digit code. The first three digits are significant. The fourth is the number of zeros following the first three. Example: 5002 is 50 seconds. For /30 and /31 types (adjustable types), the delay decade range is expressed in milliseconds in a four-digit code representing the upper limit of the range. The first three digits are significant. The fourth is the number of zeros following the first three. Example: 1001 is 1 second, so the range is 0.1 to 1 second. Terminals: P= Socket Pin Terminals S= Solder Hook Terminals Note: Mil-spec models have Y type enclosure. Typical Commercial Part Number TD2 28C P Y Series: TD2 = Time delay relay with 2 pole, 10 output Commercial Model: 28C = Fixed, Delay on Operate (COTS version of M83726/28) 29C = Fixed, Delay on Release (COTS version of M83726/29) 30C = djustable, Delay on Operate (COTS version of M83726/30) 31C = djustable, Delay on Release (COTS version of M83726/31) Time Delay Range (Within 0.1 to 600 seconds): For fixed types, the delay is expressed in milliseconds in a fourdigit code. The first three digits are significant. The fourth is the number of zeros following the first three. Example: 5002 is 50 seconds. For adjustable types, the delay decade range is expressed in milliseconds in a four-digit code representing the upper limit of the range. The first three digits are significant. The fourth is the number of zeros following the first three. Example: 1001 is 1 second, so the range is 0.1 to 1 second. Terminals: P= Socket Pin Terminals S= Solder Hook Terminals T= Solder Pin Terminals Enclosure W = Mounting Studs X = Horizontal Flange Mount Y = Raised Vertical Flange Mount Z = No Mount 5 NOTE: Commercial versions are available with timing ranges outside of.1 to 600 sec. range. For factory-direct application assistance, phone or fax Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 5

6 Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts rated low level to 5 mps VDC and 115/200 VC 400 Hz, 3 Phase n Weight.54 ounces max. (15.4 grams) n Qualified to M83536/1, /2 FC-205 Series, 5 mperes, DPDT The Series FC-205 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other forms of the FC relay: FC mp 4PDT Relay Contact Rating mperes Ratings re Continuous Duty Type of Load Life (Min.) Cycles x VDC 115VC 400Hz 115/200VC 400Hz, 3Ø Resistive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Low Level Switching Capability: With contacts operating a load of 10 to 50 microamperes at 10 to 50 millivolts, the contact resistance miss detection level shall be 100 ohms max. Cycling rate is 1 to 12 per second, for 100,000 operations. Overload Current 20 MPS DC, 30 MPS 400Hz Rupture Current 25 MPS DC, 40 MPS 400Hz Contact Make ounce 1.0 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 5 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & X Enclosures 200 g for 6 ms W & M Enclosures (Stud Mtg.) 100 g for 6 ms T Enclosure (Socket Mounted in Track) 50 g for 11 ms Vibration, Sinusoidal* Z, Y, & X Enclosures 0.12 D 10 to 70 Hz, 30 g Hz W & M Enclosures (Stud Mtg.) 0.12 D 10 to 57 Hz, 20 g Hz T Enclosure (Socket Mounted in Track) 0.06 D 10 to 57 Hz, 10 g 57 to 500Hz, 20 g 500 to 3000 Hz Vibration, Random* Z, Y, & X Enclosures 0.4 g2/hz Hz T, W & M Enclosures 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1000 V rms Coil to ground 1000 V rms t 80,000 Feet 250 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage 4 ms or less Release Time at Nominal Voltage 4 ms or less * Max. contact opening under vibration or shock 10 microseconds Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 20 Ω DC 95 Ω DC 500 Ω () 28 DC 500 Ω DC 1600 Ω COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. 5 6 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

7 FC-205 Series, 5 mperes, DPDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Terminals "" Socket Pin Terminals Socket Pins Gold Plated. Polarizing pin tin/lead plated.050 ± (1.27 ± (.13) (4.32) Silicone Rubber Gasket.200 (5.08) Solder Pin Terminals "" ll Terminals Tin/Lead Plated Solder Hook Terminals Hook Terminals Tin/Lead Plated "C".170 (4.32).200 (5.08).050 ±.002 (1.27 ±.05) polarizing pin.050 ±.002 (1.27 ±.05) polarizing pin.065 DI (1.65) ±.002 Dia Pin (1.02 ±.02) 8 Places.210 (5.33) "H" ±.001 Dia Pin (1.02 ±.02) 8 Places 90 Solder Pins ±.002 Dia Pin (1.02 ±.02) 8 Places "Z" ll Pins right cid Tin/lead.150±.015 (3.81) "Y".640 Max. (16.26).640 Max (16.26).150 (3.81).025 (.64).810 Max. (20.57) (27.38) (26.92) (3.38).410 Max. (10.4).312 (7.92) Dimensions: Inches ±.010 (mm ±.25) Enclosure "T" is for use with track mounted sockets and requires socket pin terminals, but no gasket. The gasket is included in the socket assembly..141 (3.58).640 Max (16.26) 4 PLCS.156 (3.96) Max. (32.57) ll Enclosures have Cupro-Nickel Cans bright acid tin/lead plated after assembly to terminal headers..312 (7.92).410 Max. (10.41).150± (3.81) (5.33) Enclosures "X" 4 PLCS.810 Max. (20.57) ±.020 R Typ..150 (3.81) ±.001 Dia Pin (1.02 ±.02) 8 Places.133 (3.38) "W" "T".410 Max. (10.41).080 ±.005 (2.03 ±.13).500 (12.7).172 (4.37) 4-40 UNC-2 2 Studs *.693 Max. (17.6).320 (8.13).810 Max. (20.57) (26,92) (27.38) M83536/2-028 (REFERENCE ONLY).810 Max. (20.57).158 ±.005 ** (4.01 ±.13).640 Max. (16.26).375 (9.52).032 (.79).810 Max. (20.57).055 ±.005 (1.38 ±.13).410 Max. (10.41).055 ±.005 (1.38 ±.13).110 ±.005 (2.79 ±.13) *Metric threads available,to specify use M in place of W NOTE: FOR USE WITH TRCK MOUNT PER MIL-R-6106/ Max. (10.4) ** MESURED FROM SURFCE OF HEDER Max. (32.51).025 (.64) 5 7 Catalog Revised 3-13 Dimensions are shown for reference purposes only. Specifications subject Dimensions are in millimeters unless otherwise specified. US: sia Pacific: UK: For additional support numbers please visit

8 FC-205 Series, 5 mperes, DPDT (Continued) Terminal Wiring DC Coils Transient Suppression POLRIZING PIN 3 X X2-2 1 X1 POLRIZING PIN X1 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header..150 Typ (3.81).075 (1.90).075 (1.90) 3 Polarizing Pin Typ (3.81) lue ead TERMINL VIEW HOW TO ORDER FC-205- Y 4 RELY TYPE TERMINLS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). 5 8 * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

9 FC-405 Series, 5 mperes, 4PDT Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts rated low level to 5 mps 28 VDC and 115/200 VC 400 Hz, 3 Phase n Weight.93 ounces max. (26.4 grams) n Qualified to M83536/5 & /6 The Series FC-405 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mp DPDT Relay Contact Rating mperes Ratings re Continuous Duty Type of Load Life (Min.) Cycles x VDC 115VC 400Hz 115/200VC 400Hz-3Ø Resistive Inductive Motor Lamp Low Level Switching Capability: With contacts operating a load of 10 to 50 microamperes at 10 to 50 millivolts, the contact resistance miss detection level shall be 100 ohms max. Cycling rate is 1 to 12 per second, for 100,000 operations. Overload Current 20 MPS DC, 30 MPS 400Hz Rupture Current 25 MPS DC, 40 MPS 400Hz Contact Make ounce 1.0 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 5 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z & Y Enclosures 200 g for 6 ms W, X & M Enclosures 100 g for 6 ms T Enclosure (In Track) 50 g for 11 ms Vibration, Sinusoidal* Z & Y Enclosures 30 g Hz W, X & M Enclosures 20 g Hz T Enclosure (Socket Mounted in Track) 20 g Hz Vibration, Random* Z & Y Enclosures 0.4 g2/hz Hz T, W, X & M Enclosures 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1000 V rms Coil to ground 1000 V rms t 80,000 Feet 250 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage 6 ms or less Release Time at Nominal Voltage 6 ms or less * Max. contact opening under vibration or shock 10 microseconds 5 Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 25 Ω DC 78 Ω DC 400 Ω () 28 DC 400 Ω DC 1275 Ω COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 9

10 FC-405 Series, 5 mperes, 4PDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Terminals "" Socket Pins - ll DC Coils "" Solder Pin Terminals PIN TERMINLS RE GOLD PLTED.050 ±.005 (1.27 ± (3) Silicone Rubber Gasket.170 (4.32) PIN TERMINLS TIN/LED PLTED.170 (4.32) ±.001Dia. Pin (1.02 ±.02) 14 Plcs "C" Solder Hook Terminals HOOK TERMINLS TIN/LED PLTED.210 (7.62) ±.002Dia. Pin (1.02 ±.05 ) 14 Plcs.210 (7.62) "T" ll Enclosures have cupro-nickel cans bright acid tin/lead plated after assembly to terminal headers..080 ±.005 (2.03) (±.13).640 Max. (16.26) Enclosures M83536/6-025 (REFERENCE ONLY) "Z".640 Max. (16.26) Dimensions: Inches ±.010 (mm ±.25).810 Max. (20.37).055 ±.005 (1.38) (±.13).065 Dia. typ (1.65) ±.002 Dia. Pin (1.02 ±.05 )14 Plcs.158 ** ±.005 (4.01) (±.13).110 ±.005 (2.79) (±.13) Code "T" used only with trackmounted Sockets. Requires code "" pin terminals. Gasket is included in the socket assembly..810 Max. (20.37).810 Max. (20.37).810 Max. (20.37).430 (10.92) "Y" ±.005 (±.13) "W" ** Measured from surface of header "X".141 Typ (3.58) (27.38) (26.92).640 Max. (16.26).133 Typ (3.38).810 Max. (20.37).405 (10.29).600 (5.24) (32.51).810 Max. (20.37) (27.38) (26.92).141 (3.58).810 Max. (20.37) 8 PLCS.810 Max. (20.57).025 (.64).640 Max. (16.26).025 (.64).500 (12.70).250 (6.35).156 (3.96).172 Dia (4.37).133 Typ (3.38) 4-40 UNC-2 3 Studs *.500 (12.7).712 (18.0).250 (6.35).500 (12.70).375 (9.52) ±.031 ± (.79).032 (.79).640 Max. (16.26) (32.51) 6 PLCS.810 Max. (20.37).810 Max. (20.37) 5 10 Catalog Revised 3-13 Dimensions are shown for reference purposes only. Specifications subject Dimensions are in millimeters unless otherwise specified. US: sia Pacific: UK: For additional support numbers please visit

11 FC-405 Series, 5 mperes, 4PDT (Continued) Terminal Wiring DC Coils DC Coils with Transient Suppression 3 X2-2 1 D 3 X2-2 1 D C C X1 X1 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header..450 (11.43).150 (3.81).450 (3.81).150 (3.81).300 (7.62) 5 TERMINL VIEW HOW TO ORDER FC-405- Y 4 RELY TYPE TERMINLS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 11

12 Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC, 50 to 400Hz and 400Hz C n Weight 1.6 ounces max. (45.4 grams) n Qualified to M83536/9, /10 FC-210 Series, 10 mperes, DPDT The Series FC-210 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mpere 4PDT Relay FC mpere 6 PDT Relay vailable: FC mpere DPDT Relay, Has the same specifications as the FC-210 except is rated at 15 amps. (Commercial Only) Contact Rating mperes Ratings re Continuous Duty Type of Life (Min.) 28 VDC 115VC 115/200VC 3Ø Load Cycles x Hz 400Hz 60Hz* Resistive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 40 MPS DC, 60 MPS 400Hz Rupture Current 50 MPS DC, 80 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 10 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & X Enclosures 200 g for 6 ms W & M Enclosures (Stud Mtg.) 100 g for 6 ms Vibration, Sinusoidal* Z, Y, & X Enclosures 30 g Hz W & M Enclosures (Stud Mtg.) 20 g Hz Vibration, Random* Z, Y, & X Enclosures 0.4 g2/hz Hz W & M Enclosures (Stud Mtg.) 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 10 ms or less C Relays 15 ms or less Release Time at Nominal Voltage DC Relays 10 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds 5 12 NOTE: Only DC Coil Models are QPL pproved. Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 20 Ω DC 80 Ω DC 320 Ω () 28 DC 320 Ω DC 920 Ω Hz 180 m /400Hz 100 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

13 FC-210 Series, 10 mperes, DPDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Enclosures Terminals SOCKET PINS RE GOLD PLTED POLRIZING PINS RE TIN/LED PLTED CIRCUIT ORD PINS RE TIN/LED PLTED DIMENSIONS EXCEPT S NOTED: INCHES ±.010 (MILLIMETERS ±.25) Socket Pins - ll DC Coils.050 ±.005 (1.27 ± (.127) Silicone Rubber Gasket.270 (6.86).300 (7.62) Socket Pins 115 VC D.050 ±.005 (1.27 ± (13) Silicone Rubber Gasket.270 (6.86).330 ±.030 (8.83) ± (.76) (.010) (2.92) (.152) - (.254).070 (1.78).050 (1.27).525 Max. (13.34) Socket Pins 28 VC Coils Same as Code D Except polarizing Pin turned 90 to this plane. POLRIZING PIN.062 ±.001 Dia. Pin (1.57 ±.02) 8 Plcs.270 (6.86) Max Max. (26.04).062 ±.001 Dia. Pin (1.57 ±.02) E Circuit oard Pins - ll DC Coils C Coils in. (28.57) Max. DC Coils in. (25.65) Max ±.003 (1.57) (.69) ± (.08) Dia. Polar ( ) Pin Dimensions: Inches ±.010 (mm ±.25) Z Dia. ll Enclosures have Cupro-Nickel Cans bright acid tin/lead plated after assembly to terminal headers. Y MX. Circuit oard Pins 115 VC Coils F.156 (3.96) 4 PLCS.270 (6.86) Dia ( ) Polar -.02 Pin Solder Hook Terminals (.010) (2.92) (.152) - (.254) X Dia. Pin Circuit oard Pins 28 VC Coils.550 (13.97) C Coils Max. (26.04) (35.46) (36.73) 4 PLCS.312 (7.92) "W" 6-32 UNC (9.52) 2 Studs * 0.80 DI (2.03) Dia. Term. (1.57).05 8 Plcs -.02 H 90 Solder Pins ll Pins right cid Tin/lead.400 (10.61).200 (5.08).200 (5.08) Dia. Catalog Revised 3-13 Dimensions are shown for reference purposes only. Specifications subject Dimensions are in millimeters unless otherwise specified..031 (.787) MX Max. (26.04).200 (5.08).257 (6.52).525 Max. (13.34).100 R Typ. (1.02) Max. (43.64) POLRIZING PIN.300 ±.020 (7.62)± (12.70) DC Coils.525 Max. (13.34) Same as Code F Except polarizing Pin turned 90 to this plane. HOOK TERMINLS TIN/LED PLTED.150 (3.8).375 (9.52) Max Max. (43.64) ±.003 (1.57) (.69) ± (.08) Dia. G.375 (9.52).070 (1.78).050 (1.27) C.150 (3.8).525 Max. (13.34).330 ±.030 (8.83) ± (.76).062 ±.001 Dia. Pin (1.57 ±.02) 8 Plcs (1.02).625 (5.88).200 (5.08) *Metric threads available,to specify use M in place of W US: sia Pacific: UK: For additional support numbers please visit (7.62) Max. (26.04) (36.73) (35.46)

14 FC-210 Series, 10 mperes, DPDT (Continued) Terminal Wiring DC Coils with Transient Suppression DC Coils C Coils 115 VC C Coils 28 VC 1 POLRIZING PIN X2 - X1 2 3 POLRIZING PIN 1 X2 - X POLRIZING PIN X2 X1 C POLRIZING PIN X2 X1 C 2 3 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header..200 (5.08).100 (2.54).100 (2.54).100 (2.54) (10.16).600 (15.24) 3 TERMINL VIEW.200 (5.08) HOW TO ORDER FC-215- FC-210- Y 4 RELY TYPE TERMINLS (Socket Pins, DC Coil) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL pproved 5 14 * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

15 FC-212 Series, 12 mperes, DPDT Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC, 50 to 400Hz and 400Hz C n Weight 1.6 ounces max. (45.4 grams) The Series FC-212 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mp 4PDT Relay Contact Rating mperes Ratings re Continuous Duty Type of Life (Min.) 28 VDC 115VC 115/200VC 3Ø Load Cycles x Hz 400Hz 60Hz* Resistive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 40 MPS DC, 60 MPS 400Hz Rupture Current 50 MPS DC, 80 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 12 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & X Enclosures 200 g for 6 ms W & M Enclosures (Stud Mtg.) 100 g for 6 ms Vibration, Sinusoidal* Z, Y, & X Enclosures 30 g Hz W Enclosure 20 g Hz Vibration, Random* Z, Y, & X Enclosures 0.4 g2/hz Hz W & M Enclosures (Stud Mtg.) 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 10 ms or less C Relays 15 ms or less Release Time at Nominal Voltage DC Relays 10 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 20 Ω DC 80 Ω DC 320 Ω () 28 DC 320 Ω DC 920 Ω Hz 180 m /400Hz 100 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. 5 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 15

16 FC-212 Series, 12 mperes, DPDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Enclosures Terminals SOCKET PINS RE GOLD PLTED POLRIZING PINS RE TIN/LED PLTED CIRCUIT ORD PINS RE TIN/LED PLTED DIMENSIONS EXCEPT S NOTED: INCHES ±.010 (MILLIMETERS ±.25) Socket Pins - ll DC Coils.050 ±.005 (1.27 ± (.127) Silicone Rubber Gasket.270 (6.86).300 (7.62) Socket Pins 115 VC D.050 ±.005 (1.27 ± (13) Silicone Rubber Gasket.270 (6.86).330 ±.030 (8.83) ± (.76) (.010) (2.92) (.152) - (.254).070 (1.78).050 (1.27) Max Max. (26.04).062 ±.001 Dia. Pin (1.57 ±.02).525 Max. (13.34) Socket Pins 28 VC Coils E Same as Code D Except polarizing Pin turned 90 to this plane. POLRIZING PIN.062 ±.001 Dia. Pin (1.57 ±.02) 8 Plcs Y MX. Circuit oard Pins - ll DC Coils F.270 (6.86) C Coils in. (28.57) Max. DC Coils in. (25.65) Max ±.003 (1.57) (.69) ± (.08) Dia. Polar ( ) Pin Dimensions: Inches ±.010 (mm ±.25) Z Dia. ll Enclosures have Cupro-Nickel Cans bright acid tin/lead plated after assembly to terminal headers. Circuit oard Pins 115 VC Coils.156 (3.96) 4 PLCS.270 (6.86).300 (7.62) Dia ( ) Polar -.02 Pin Solder Hook Terminals Max. (43.64) X G Dia. Pin Circuit oard Pins 28 VC Coils.550 (13.97) C Coils Max. (26.04) (35.46) (36.73) 4 PLCS Max. (43.64) POLRIZING PIN.312 (7.92) "W" 6-32 UNC DI (2.03) Dia. Term. (1.57).05 8 Plcs -.02 H 90 Solder Pins ll Pins right cid Tin/lead.400 (10.61) Max. (26.04).200 (5.08) Dia Catalog Revised 3-13 Dimensions are shown for reference purposes only. Specifications subject Dimensions are in millimeters unless otherwise specified..200 (5.08).257 (6.52).525 Max. (13.34).100 R Typ..031 (.787) MX..200 (5.08) (1.02).375 (9.52) 2 Studs *.300 ±.020 (7.62)± (12.70) DC Coils.525 Max. (13.34) Same as Code F Except polarizing Pin turned 90 to this plane. HOOK TERMINLS TIN/LED PLTED.150 (3.8).375 (9.52) Max. C.150 (3.8).375 (9.52).070 (1.78).050 (1.27) ±.003 (1.57) (.69) ± (.08) Dia..062 ±.001 Dia. Pin (1.57 ±.02) 8 Plcs (1.02).525 Max. (13.34).330 ±.030 (8.83) ± (.76) (.010) (2.92) (.152) - (.254) Max. (26.04) (36.73) (35.46).625 (5.88).200 (5.08) *Metric threads available,to specify use M in place of W US: sia Pacific: UK: For additional support numbers please visit

17 FC-212 Series, 12 mperes, DPDT (Continued) Terminal Wiring DC Coils with Transient Suppression DC Coils C Coils 115 VC C Coils 28 VC 1 POLRIZING PIN X2 - X1 2 3 POLRIZING PIN 1 X2 - X POLRIZING PIN X2 X1 C POLRIZING PIN X2 X1 C 2 3 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header..200 (5.08).100 (2.54).100 (2.54).100 (2.54) (10.16).600 (15.24) 3 TERMINL VIEW.200 (5.08) 5 HOW TO ORDER FC-212- Y 4 RELY TYPE TERMINLS (Socket Pins, DC Coil) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 17

18 Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n 4PDT switching in one inch cube n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC and C 50 to 400Hz or 400Hz n Weight 2.72 ounces max. (77 grams max.) n Qualified to M83536/15, /16 FC-410 Series, 10 mperes, 4PDT The Series FC-410 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture 2-pole and 6-pole versions of this relay. FC mp DPDT Relay FC mp 6PDT Relay vailable FC mp 4PDT, Has the same specifications as the FC-410 except is rated at 15 amps. (Commercial Only) Contact Rating mperes Ratings re Continuous Duty Type of Life (Min.) 28 VDC 120VC 120/200VC Load Cycles x Hz 400Hz-3Ø 60Hz-3Ø* Resistive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 40 MPS DC, 60 MPS 400Hz Rupture Current 50 MPS DC, 80 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 10 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z & Y Enclosures 200 g for 6 ms W, X & M Enclosures 100 g for 6 ms Vibration, Sinusoidal* Z & Y Enclosures 0.12 D 10 to 70Hz 30 g 70 to 3000Hz W, X & M Enclosures 0.12 D 10 to 57Hz 20 g 57 to 3000Hz Vibration, Random* Z & Y Enclosures 0.4 g2/hz Hz W, X & M Enclosures 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 15 ms or less C Relays 20 ms or less Release Time at Nominal Voltage DC Relays 15 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 18 Ω DC 70 Ω DC 290 Ω () 28 DC 290 Ω DC 865 Ω Hz 225 m /400Hz 120 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVER-VOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. NOTE: Only DC Coil Models are QPL pproved Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

19 FC-410 Series, 10 mperes, 4PDT (Continued) elow are shown the standard terminal types and the enclosures available. Note that the pin configuration for coil connections is determined by the coil supply voltage. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25) except as noted. Enclosures Terminals Terminals on centers. Coil terminals: X1. Socket Pins are Gold Plated. Circuit oard Pins are Tin/Lead Plated. Socket Pins-ll DC Coils ll Enclosures have cupro-nickel cans bright acid tin/lead plated after assembly to terminal headers. Socket Pins-115 VC Coils.050 ±.005 (1.27 ± (3) Silicone Rubber Gasket.270 (6.86) Z.100 (25.4) ±.005 (1.27 ± (3) Silicone Rubber Gasket.270 (6.86) D ±.001 Pin (1.57 ±.02 ) 14 places.150 typ. Y (3.8).062 ±.001 Pin (1.57 ±.02 ) 14 places Circuit oard Pins-ll DC Coils.270 (6.86) PLCS SEE NEXT PGE 5 (35.46) (36.73) Dia. Pin ( ) 14 Plcs..02 FOR MORE COIL (25.4) TERMINL OPTIONS "W" C Solder Hooks-C or DC Coils X.150 Typ. (3.8) (25.4).300 ±.020 (7.26) ±.51 (1.02).156 (3.96) Max. (43.64) 0.80 DI (2.03) 6 PLCS.312 (7.92) 6-32 UNC-2 3 Studs *.375 (9.52) (25.4).031 (.787) (25.78) (35.46) (36.73).343 (8.71).687 (17.44).160 (4.06) Dia. Pin ( )14 Plcs Max. (43.64).687 (17.44).160 (4.06) (1.02) *Metric threads available,to specify use M in place of W 5 19 Catalog Revised 3-13 Dimensions are shown for reference purposes only. Specifications subject Dimensions are in millimeters unless otherwise specified. US: sia Pacific: UK: For additional support numbers please visit

20 FC-410 Series, 10 mperes, 4PDT (Continued) Terminals (Continued) E Socket Pins- 28 VC Coils.270 (6.86).050 ±.005 (1.27 ± (3) Silicone Rubber Gasket F Circuit oard Pins-115 VC Coils.270 (6.86) G Circuit oard Pins- 28 VC Coils.270 (6.86) Dia. Pin ( ) 14 Plcs Dia. Pin ( ) 14 Plcs Dia. Pin ( ) 14 Plcs Terminal Wiring & Pin Terminal ll DC Coils 1 X2 2 3 D - C Hook Terminal ll C & DC Coils 1 X2 2 3 D - Transient Suppression D & F Pin Terminal Cir. 115 VC Coils 1 X D - D E & G Pin Terminal 28 VC Coils D C C C C C X2 X1 C C X X1 X1 X1 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header. HOW TO ORDER RELY TYPE TERMINLS (Socket Pins) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL pproved.400 (10.16).600 (15.24).400 (10.16).200 (5.08) Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit TERMINL VIEW.200 (5.08) X1 FC-415- FC-410 Y 4 * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section (15.24)

21 FC-125 Series, 25 mperes, SPDT Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC, 50 to 400Hz and 400Hz C n Weight 1.6 ounces max. (45.4 grams) n Qualified to M6106/19, M83536/36, /37 The Series FC-125 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mpere 3PDT Relay FCC mpere 3PST-NO Relay with 2 amp SPDT auxiliary Contact Rating mperes Ratings re Continuous Duty Type of Load Life (Min.) Cycles x VDC 115VC 400Hz 115VC 60Hz* Resistive Inductive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 50 MPS DC, 80 MPS 400Hz Rupture Current 60 MPS DC, 100 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 25 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & X Enclosures 200 g for 6 ms W & M Enclosures (Stud Mtg.) 100 g for 6 ms Vibration, Sinusoidal* Z, Y, & X Enclosures 30 g Hz W & M Enclosures (Stud Mtg.) 20 g Hz Vibration, Random* Z, Y, & X Enclosures 0.4 g2/hz Hz W & M Enclosures (Stud Mtg.) 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 10 ms or less C Relays 15 ms or less Release Time at Nominal Voltage DC Relays 10 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds 5 Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 20 Ω DC 80 Ω DC 320 Ω () 28 DC 320 Ω DC 920 Ω Hz 180 m /400Hz 100 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. NOTE: Only DC Coil Models are QPL pproved. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 21

22 FC-125 Series, 25 mperes, SPDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Terminals Enclosures 5 22 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

23 FC-125 Series, 25 mperes, SPDT (Continued) Terminal Wiring HOW TO ORDER TERMINL VIEW 5 FC-125- Y 4 RELY TYPE TERMINLS (Socket Pins, DC Coil) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL pproved * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 23

24 Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC, 50 to 400Hz and 400Hz C n Weight 2.89 ounces max. (82 grams) n Qualified to M83536/32, /33 FC-325 Series, 25 mperes, 3PDT The Series FC-325 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mp SPDT Relay FCC mpere 3PST-NO Relay with 2 amp SPDT auxiliary Contact Rating mperes Ratings re Continuous Duty Type of Life (Min.) 28 VDC 115VC 115/200VC Load Cycles x Hz 400Hz-3Ø 60Hz-3Ø* Resistive Inductive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 50 MPS DC, 80 MPS 400Hz Rupture Current 60 MPS DC, 100 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE Max. Contact Drop at 25 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & V Enclosures 200 g for 6 ms W, X & M Enclosures 100 g for 6 ms Vibration, Sinusoidal* Z, Y, & V Enclosures 30 g Hz W, X & M Enclosures 20 g Hz Vibration, Random* Z, Y, & V Enclosures 0.4 g2/hz Hz W, X & M Enclosures 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 15 ms or less C Relays 20 ms or less Release Time at Nominal Voltage DC Relays 15 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds 5 24 Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 18 Ω DC 70 Ω DC 290 Ω () 28 DC 290 Ω DC 865 Ω Hz 225 m /400Hz 120 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVER-VOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. NOTE: Only DC Coil Models are QPL pproved. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

25 FC-325 Series, 25 mperes, 3PDT (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Terminals Socket Pins - ll DC Coils Solder Pin Terminals PIN TERMINLS RE GOLD PLTED.050 ±.005 (1.27 ± (.12) Silicone Rubber Gasket.250 (6.35).270 (6.86) PIN TERMINLS TIN/LED PLTED HOOK TERMINLS TIN/LED PLTED.250 (6.35).375 ±.020 (9.52 ±.508).270 (6.86).062 ±.001 Dia. Pin (1.57 ±.02) 2 Plcs C Solder Hook Terminals.625 ±.020 (15.88 ±.51).062 ±.001Dia. Pin (1.57 ±.02) 2 Plcs.300 ±.020 (7.62 ±.51) ±.002 Dia. Pin (1.02 ±.05 ) 2 Plcs Dia. Pin.05 ( ) 9 Plcs "V" Dia. Pin ( ) 9 Plcs -.00 Enclosures.150 Typ. (3.8) ±.003 Dia.Pin (2.36 ±.08) 9 Plcs ll Enclosures have cupro-nickel cans bright acid tin/lead plated after assembly to terminal headers. Z (2.54) 5 Dimensions: Inches ±.010 (mm ±.25) 6 PLCS For socket pin terminals: specify Y enclosures with DC coils and "V" enclosures with C coils. (25.4) Max. (43.64) Y (1.02).156 (3.96).150 typ. (3.8) 6 PLCS (35.46) (36.73) 6 PLCS (7.92) 6-32 UNC-2 3 Studs *.375 (9.52) (25.4).047 (1.20) (35.46) (36.73) (25.78).343 (8.71).687 (17.44).160 (4.06) Max. (43.64) Max. (43.64) "W".150 typ. (3.8) (25.4) Catalog Revised 3-13 X (25.4) (35.46) (36.73) (1.02).687 (17.44).160 (4.06) (1.02).156 (3.96) Dimensions are shown for reference purposes only. Specifications subject *Metric threads available,to specify use M in place of W 5 25 Dimensions are in millimeters unless otherwise specified. US: sia Pacific: UK: For additional support numbers please visit

26 FC-325 Series, 25 mperes, 3PDT (Continued) Terminal Wiring DC Coils DC Coils with Transient Suppression C Coils 1 X2-2 3 C 1 X2-2 3 C 1 X2 2 3 C X1 X1 C X1 NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header..150 (3.81).450 (11.43).630 (16.00).300 (7.62).600 (15.24).432 (10.97).234 (5.94) TERMINL VIEW HOW TO ORDER FC-325- Y 4 RELY TYPE TERMINLS (Socket Pins, DC Coil) ENCLOSURE (With Flanges) COIL (28 VDC With Transient Suppression). NOTE: Only DC coil models are QPL pproved 5 26 * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

27 FCC-325 Series, 25 mperes, 3PST-NO with 2 mp SPDT uxiliary Contacts Product Facts n Hermetically Sealed n ll Welded Construction n alanced Force n Permanent Magnet Drive n Contacts Silver Cadmium Oxide with Gold Plating n Coils for DC, 50 to 400Hz and 400Hz C n Weight 2.89 ounces max. (82grams) The Series FCC-325 relay is a polarized single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return nonpolar design. We also manufacture other versions of this relay: FC mpere SPDT Relay FC mpere 3PDT Relay Contact Rating mperes Ratings re Continuous Duty Life (Min.) 115VC Type of Cycles 28 VDC 400Hz 115/200VC 115/200VC Load 400Hz-3Ø 60Hz-3Ø* x103 Main ux. Main ux. Resistive Inductive Inductive Motor Lamp *60 Hz loads rated for 10,000 operations Overload Current 50 MPS DC, 80 MPS 400Hz Rupture Current 60 MPS DC, 100 MPS 400Hz Contact Make ounce 1 MILLISECOND T NOMINL VOLTGE uxiliary Contact ounce 4 MILLISECONDS MX. Max. Contact Drop at 25 mps INITIL VOLTS End of Life VOLTS General Specifications Temperature Rating -70 C TO 125 C ltitude 300,000 Feet Shock* Z, Y, & V Enclosures 200 g for 6 ms W, X & M Enclosures 100 g for 6 ms Vibration, Sinusoidal* Z, Y, & VEnclosures 30 g Hz W, X & M Enclosures 20 g Hz Vibration, Random* Z, Y, & V Enclosures 0.4 g2/hz Hz W, X & M Enclosures 0.2 g2/hz Hz Dielectric Strength t Sea Level ll circuits to ground and circuit to circuit 1250 V rms Coil to ground 1000 V rms t 80,000 Feet 350 V rms Insulation Resistance Initial (500 VDC) 100 MΩ Min. fter Life or Environmental Tests 50 MΩ Min. Operate Time at Nominal Voltage DC Relays 15 ms or less C Relays 10 ms or less Release Time at Nominal Voltage DC Relays 15 ms or less C Relays 50 ms or less * Max. contact opening under vibration or shock 10 microseconds 5 Coil Data Over Temperature Range Coil Nominal Freq. DC Res. Code Voltages Hz C mps () Pickup or Dropout or Must Hold elow Volts bove Volts Voltage (C) 1 6 DC 18 Ω DC 70 Ω DC 290 Ω () 28 DC 290 Ω DC 865 Ω Hz 225 m /400Hz 120 m Hz 40 m /400 Hz 30 m COILS HVE CK EMF SUPPRESSION TO 42 VOLTS MX.. DC COIL RESISTNCE ± 10% T 25 C; C COIL MX. CURRENT T NOMINL VOLTGE. C. RELY WILL STY IN PICKED-UP STTE DOWN TO MUST HOLD VOLTGES SHOWN. D. MX. OVERVOLTGE: 6 & 12 VDC COILS 120% OF NOMINL; LL OTHERS 110% OF NOMINL. E. COILS VILLE FOR OTHER VOLTGES ND FOR C 50/60HZ. Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 27

28 FCC-325 Series (Continued) elow are shown the standard terminal types and the enclosures available. Specify the assembly as indicated under How To Order. Dimensions are shown in inches ±.010 and (Millimeters ±.25). Terminals "" Socket Pin Terminals Pin Terminals are Gold Plated.250 (6.35) "V".150 typ. (3.8).050 ±.005 (1.27 ± (13) Silicone Rubber Gasket "" Solder Pin Terminals Pin Terminals are Tin/Lead Plated.250 (6.35) (7.62) (7.62).270 ± (6.86).062 Dia. Pin.062 ±.001Dia. Pin (1.57 ±.02) 5 Plcs (6.86) (1.57 ±.02) 5 Plcs.062 ±.002Dia. Pin.062 ±.002Dia. Pin (1.57 ±.05) (1.57 ±.05) REGISTRTION PIN REGISTRTION PIN Dia. Pin Dia. Pin (2.36 ) 6 Plcs (2.36 ) 6 Plcs ENCLOSURES ll Enclosures have cupro-nickel cans bright acid tin/lead plated after assembly to terminal headers. "C" Solder Hook Terminals Hook Terminals are Tin/Lead Plated.300 ±.020 (7.62)±.51 "Z" (25.4).375 ±.020 (9.52)± ±.020 (15.88)±.51 ±.002Dia. Pin (1.02 ±.05) 2 Plcs.093 ±.003 Dia.Pin (2.36 ±.08) 9 Plcs 6 PLCS (35.46) (36.73) Dimensions: Inches ±.010 (mm ±.25) For socket pin terminals: specify "Y" enclosures with DC coils and "V" enclosures with C coils. "Y" 6 PLCS (25.4) (25.4).150 typ. (3.8) Max. (43.64) (35.46) (36.73) Max. (43.64) (1.02).156 (3.96) (1.02).156 (3.96) "X" 6 PLCS (25.4).150 typ. (3.8) (35.46) (36.73) Max. (43.64) (1.02) "W".312 (7.92) 6-32 UNC-2 3 Studs * (25.4) (25.78).375 (9.52).047 (1.20).687 (17.44).343 (8.71).160 (4.06).160 (4.06).687 (17.44) *Metric threads available, To specify use M in place of W 5 28 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

29 FCC-325 Series (Continued) Terminal Wiring TERMINL WIRING DC COILS 1 2 DC COILS WITH TRNSIENT SUPPRESSION C COILS 2 C X2-12 C X2-12 C X2 12 X1 U X X1 U X C X1 U X NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity. Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header. HOW TO ORDER.150 (3.81).450 (11.43) REGISTRTION PIN.630 (16.00).432 (10.97) TERMINL VIEW.300 (7.62).234 (5.94).600 (15.24) 5 FCC Y 4 RELY TYPE TERMINLS (Socket Pins, DC Coil) ENCLOSURE (With Flanges and DC Coil) COIL (28 VDC With Transient Suppression) Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 29

30 FC-150 Series, 50 mps, 1PST/NO (DM) Relay Product Facts n Non-latching relay n alanced force design n Corrosion protected metal enclosure n ll welded hermetically sealed enclosure occupies about 1 in3 (16.4 cm 3 ) n 1 Form X (SPST-NO-DM) n 6, 12 and 28 Vdc coils n Weight: 90 grams n Designed and built in accordance to MIL-PRF-6106 The FC-150 series relay is a polarized, single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return non-polar design. 1 Form X (SPST-NO-DM) configuration with main contacts rated 50 mps. Specifications Contact Data Contact Form 1 Form X (SPST-NO-DM) Contact Rating in mps (Continuous Duty) Type of Life (Min.) Load Cycles 28 Vdc Resistive 50, Inductive (L/R=5ms) 20, Motor 20, None 100,000 Overload Current (Resistive) 200, 50 cycles Max. Contact Drop at 10 Initial 30mV; fter Life 175mV Operate Time at Nominal Voltage 15ms Release Time 15ms ounce Time 1ms Coil Data Coil Code Nominal Operating Voltage (Vdc) Maximum Operating Voltage (Vdc) Maximum Pick-Up Voltage at 125 C Maximum Pick-Up Voltage at 125 C, continuous current test (Vdc) Drop-Out Voltage at OTR Maximum Coil Current at 25 C () ack EMF Suppressed to (Vdc) (Max) N/ N/ N/ -42 Coil Resistance ±10% 18Ω 70Ω 290Ω 290Ω 5 30 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

31 FC-150 Series, 50 mps, 1PST/NO (DM) Relay (Continued) Specifications Electrical Data Initial Insulation Resistance (note 1) Insulation Resistance fter Life or Environmental Test (note 1) Dielectric Strength t Sea Level Contacts to Ground and etween Contacts Coil to Ground Dielectric Strength at 80,000 ft (25,000m), ll Points (note 4) Environmental Data mbient Temperature Range, Operating ltitude Shock Resistance Vibration Resistance, Sinusoidal Mechanical Data pproximate Weight 100 megohms, minimum, at 500Vdc, between each pin and case 50 megohms, minimum, at 500Vdc, between each pin and case 1,250Vrms, 60 Hz. 1,000Vrms, 60 Hz. 500Vrms, 60 Hz -70 C to 125 C 300,000 feet 50 G s, 11 ms. 20 G s, Hz. 3.2 oz. (90g) Max. NOTES 1. ll wired terminals must be connected together during this test. Dielectric withstanding voltage and insulation resistance are measured between all mutually insulated wired terminals and between all these terminals and case. Terminals Solder Pin Terminals Tin/Lead Plated C Solder Hook Terminals Tin/Lead Plated K Terminal Shield GOLD PIN TERMINLS FOR MIL-C-39029/ SOCKET PINS.062±.002 DI PINS 2 PLCS).062±.002 DI HOOKS 2 (PLCS).510 M4 x.7 STUD (2X) DIN 6798 LOCK WSHER DIN 934 NUT HEX (4X) UNC-2 STUD MS LOCK WSHER N961-8T FLT WSHER MS T NUT, HEX 2 ECH REQUIRED UNC-2 STUD MS LOCK WSHER N961-8T FLT WSHER MS T NUT, HEX 2 ECH REQUIRED Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 31

32 FC-150 Series, 50 mps, 1PST/NO (DM) Relay (Continued) Outline Dimensions The standard terminal types and enclosures are illustrated below with dimensions in inches ± and (millimeters ±0.25). Enclosures "U" MX.150 "Y" MX PLCS.156 "X" "R" "Z" 6 PLCS MX Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

33 FC-150 Series, 50 mps, 1PST/NO (DM) Relay (Continued) Terminal Wiring DC Coils 1 DC Coils with Transient Suppression 1 2 ED 2 ED NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header TERMINL VIEW 5 How to Order Typical Part Number FC Y 3 Series and Contact rrangement: FC-150 = Relay with 1 Form X Main Contacts Terminals (see drawings for details): = Solder Pin Coil Terminals, Stud Power Terminals C = Solder Hook Coil Terminals, Stud Power Terminals K = Terminal lock, Stud Power Terminals Enclosure (see drawings for details): R = Horizontal Flange Mount, Rotated U = Flush Vertical Flange Mount X = Horizontal Flange Mount Y = Raised Vertical Flange Mount Z = No Mount Coil: 1 = 6Vdc nominal 2 = 12Vdc nominal 3 = 28Vdc nominal 4 = 28Vdc nominal, with back EMF suppression Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 33

34 FC-150NC Series, 50 mps, 1PST/NC (D) Relay Product Facts n Non latching hermetically sealed relay n alanced force design n Hermetically sealed, corrosion protected metal can n ll welded construction n 6, 12 and 28Vdc coils available. n Weight 90 grams n Designed and built in accordance to MIL-PRF-6106 Specifications General Characteristics Temperature range -70 C to 125 C ltitude 300,000 feet Dielectric strength at sea level - Contacts to ground and between contacts 1250 Vrms / 60 Hz - Coil to ground 1000 Vrms / 60 Hz Dielectric strength at altitude m (80,000 ft) (all points) 500 Vrms / 60 Hz Initial insulation resistance at 500 Vdc 100 MΩ min. Initial insulation after life or environmental test 50 MΩ min. Sinusoidal vibration 20g / 75 to 3000 Hz Shock 50g / 11 ms Operate time at nominal voltage 15 ms max. Release time 15 ms max. ounce time 1 ms max. Contact voltage drop at nominal current -initial value 150 mv max. -after life 175 mv max. Coil Data Coil Code () Nominal Operating Voltage (Vdc) Maximum Operating Voltage (Vdc) Maximum Pick-Up Voltage at 125 C Maximum Pick-Up Voltage at 125 C, continuous current test (Vdc) Drop-Out Voltage at OTR Maximum Coil Current at 25 C (m) ack EMF Suppressed to (Vdc) N/ N/ N/ -42 Coil Resistance 18Ω 70Ω 290Ω 290Ω For other coil voltages, consult factory Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

35 FC-150NC Series, 50 mps, 1PST/NC (D) Relay (Continued) Contact Electrical Characteristics Contact Type Rated Current Rated Voltage Main Contact 50 28Vdc Minimum Operating cycles Contact rating per pole and load type Load Currents in mps MIN Contact 50,000 cycles Resistive load 50 20,000 cycles Inductive load (L/R=5ms) 20 20,000 cycles Motor load cycles Resistive overload ,000 cycles No Load ll endurance ratings are subject to validation - consult factory Terminals Solder Pin Terminals Tin/Lead Plated C Solder Hook Terminals Tin/Lead Plated K Terminal Shield GOLD PIN TERMINLS FOR MIL-C-39029/ SOCKET PINS.062±.002 DI PINS 2 PLCS).062±.002 DI HOOKS 2 (PLCS) M4 x.7 STUD (2X) DIN 6798 LOCK WSHER (2X) DIN 934 NUT HEX (4X) UNC-2 STUD MS LOCK WSHER N961-8T FLT WSHER MS T NUT, HEX 2 ECH REQUIRED UNC-2 STUD MS LOCK WSHER N961-8T FLT WSHER MS T NUT, HEX 2 ECH REQUIRED Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 35

36 FC-150NC Series, 50 mps, 1PST/NC (D) Relay (Continued) Outline Dimensions The standard terminal types and enclosures are illustrated below with dimensions in inches ± and (millimeters ±0.25). Enclosures "U" "Y" MX "Z" MX PLCS "X" "V" "R" MX PLCS MX 6 PLCS Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit

37 FC-150NC Series, 50 mps, 1PST/NC (D) Relay (Continued) Terminal Wiring DC Coils 1 DC Coils with Transient Suppression 1 2 ED 2 ED NOTE: Polarity must be observed with DC coil supply. Relay is polarized with a permanent magnet and will not operate or be damaged by reverse polarity Diodes used in transient suppression and in C rectifier circuits have peak inverse voltage rating of 600 VDC minimum. Zener diodes have a minimum rating of 1 watt. Terminal designations are for reference only and do not appear on the header PRT NUMERING SYSTEM TERMINL VIEW 5 FC - 150NC Y 4 RELY TYPE TERMINLS ENCLOSURE COIL Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit 5 37

38 FCC-150 Series, 50 mps, 1PST/NO (DM) with 1PDT uxiliary Contacts Product Facts n Non-latching relay n alanced force design n Corrosion protected metal enclosure n ll welded hermetically sealed enclosure occupies about 1 in3 (16.4 cm 3 ) n 1 Form C (SPDT) auxiliary contact n 6, 12 and 28 Vdc coils n Weight: 90 grams n Designed and built in accordance to MIL-PRF-6106 The FCC-150 series relay is a polarized, single-side stable design, where the flux from a permanent magnet provides the armature holding force in the deactivated state, and its flux path is switched and combined with the coil flux in the operated state. This results in appreciably increased contact pressure in both states over that of a spring return non-polar design. 1 form C (SPDT) auxiliary contact set rated 2 amps is available. Specifications uxiliary Contact Data Contact Form 1 Form X (SPDT-NO-DM) with 1 Form C (SPDT) uxiliary Contact Rating in mps (Continuous Duty) Type of Life (Min.) 115 Vac Load Cycles 28 Vdc 400Hz Resistive 50, Inductive (L/R=5ms) 20, Motor 20, None 100,000 Coil Data Coil Code () Nominal Operating Voltage (Vdc) Maximum Operating Voltage (Vdc) Maximum Pick-Up Voltage at 125 C Maximum Pick-Up Voltage at 125 C, continuous current test (Vdc) Drop-Out Voltage at OTR Maximum Coil Current at 25 C (m) ack EMF Suppressed to (Vdc) (max) N/ N/ N/ -42 Coil Resistance ±10% 18Ω 70Ω 290Ω 290Ω 5 38 Revised 3-13 reference purposes only. unless otherwise specified. sia Pacific: please visit