MH Series, W. Input Ranges : 9-75 VDC

Size: px
Start display at page:

Download "MH Series, W. Input Ranges : 9-75 VDC"

Transcription

1 MH Series, W Input Ranges : 9-5 VDC Voltage: Single 12V - 4V Dual +5.0V/+12V +5.0V/+15V Triple +5.0V/, +5.0V/, Power: W FEATURES General: Small footprint : 3.0 x 3.0 High output power : to 300 watts Wide input range : 10-5Vdc Open frame or encapsulated Integral PCB transformer High conversion efficiency to 93% Line regulation to ±0.1% Load regulation to ±0.5% Fixed operating frequency : over-voltage protection over-load protection Hiccup mode short circuit protection Over-temperature protection Input under-voltage lock-out Input over-voltage shut-down Control: Enable (On/Off) Control Voltage Trim Isolation: Isolation Voltage > 500V MH series is a family of high power density, high efficiency, and high reliability DC-DC Converters. It provides up to 300W output in a 3.0 x 3.0 footprint. The wide input range (2:1 & 3:1) is ideal for battery or unregulated input applications. Integral PCB transformer / inductor is used for all models in this series. This new design technique has greatly improved the magnetic coupling, reduced switching spike and provided performance consistency. It also streamlines the production process by completely eliminating the hand-wind magnetic assembly process from production lines. MH series provides the most extensive protection to safeguard both the power converter and the load. It includes output over-voltage protection, over-current protection, hiccup mode indefinite short circuit protection, under-voltage lockout and over-temperature protection. Over-current inception point is set at about 115% of rated load. Hiccup mode cycles for 2mSec periods with 3mSec on and 25mSec off. Over-temperature shutdown, activated at +105 C of board temperature, will recover when the temperature falls below +95 C. MH series features low output noise, very tight line and load regulation, and high efficiency. No external capacitor requirement for normal operation. TABLE OF CONTANTS : General Specifications... 2 Single... 4 Dual... 9 Triple ACON, INC. MH Series Rev. Jan. 2, 200 Pg. of 15

2 MH Series, W 1. Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause performance degradation, adversely effect longterm reliability, and cause permanent damage to the device. Parameter Voltage Range Designator / Description Min Max Units Input Voltage Vdc Vdc Continuous Vdc Vdc Vdc Vdc Transient Vdc Vdc (100mSec.) Vdc Vdc Operating Temperature All models, base plate temperature C Storage Temperature Ambient C Isolation Voltage Input to Vdc 2. Input Specifications Parameter Conditions / Description Min Nom Max Units Input Voltage Voltage Range (Continuous) Under-Voltage Lockout (UVLO) Turn-On Threshold (Ramping Up) Turn-Off Threshold (Ramping Down) Vdc Vdc Vdc Vdc Vdc Vdc 24 1 Vdc 4 35 Vdc Vdc 60 1 Vdc Vdc Vdc 4 33 Vdc Vdc Vdc 3. Enable (On-Off Control) Parameter Conditions / Description Min Nom Max Units Enable Pin Open Circuit Voltage 10 Vdc Source Current 1 ma Positive Logic Standard On-Control Logic High or Floating Vdc Off-Control Vdc Negative Logic Optional (Please add Suffix N) On-Control Vdc Off-Control Logic High or Floating Vdc ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 2 of 15

3 4. Specifications Parameter Conditions / Description Min Nom Max Units Voltage Accuracy Please see table % Current Please see table Adc Start-Up Time 150 msec. Trim ±5 %Vout Over Voltage 120 %Vdc Line Regulation ±0.1 %Vout Load Regulation ±0.5 %Vout Transient Respoonse 50% ± 25% step load change 400 µsec. Ripple & Noise Please see table mvp-p Switching Frequency 250 KHz 5. Trim Parameter Conditions / Description Min Nom Max Units Negative Trim Standard Trim Up Trim Pin to (-)Vout 5 %Vdc Trim Down Trim Pin to (+)Vout 5 %Vdc Positive Trim Not Available *Trim pin can be left floating if not used MH Series, W 6. Environmental and Mechanical Specifications Parameter Conditions / Description Min Nom Max Units Operating Temperature PCB Temperature Standard C Extended Optional - (Please add Suffix C) C Storage Temperature C Temperature Coefficient ±0.02 %/ C Shock Halfsine wave, 3 axes 50 g Sinusoidal Vibration GR-63-CORE, Section g Humidity Relative Humidity, Non-Condensing 95 %R.H. Weight PC Board Mount 6.4(10) Oz(g) Chassis Mount.(21) Oz(g) MTBF (calculated) Bellcore TR-NWT method 1 - parts count 1 MHrs. Isolation Specifications Parameter Conditions / Description Min Nom Max Units Isolation Voltage Input to 500 Vdc I/O to Case 500 Vdc Isolation Resistance Input to 10 MΩ Isolation Capacitance Input to 3 nf. s Parameter Conditions / Description Min Nom Max Units Over-Load Type Current-Mode, Pulse by Pulse Current Limit Threshold % Rated Load 120 % Short-Circuit Type Hiccup Mode, Non-Latching, Auto-Recovery Threshold Short-Circuit Resistance 65 mω Over-Temperature Type Non-Latching, Auto-Recovery Threshold PCB Temperature 105 C Hysteresis 15 C Over-Voltage Type Auxiliary Feedback Loop Control Set-Point 120 %Vout ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 3 of 15

4 MH Series, Single W BLOCK DIAGRAM (+)Vin 1 (+)Vin 2 (+)Vout (-)Vin 4 (-)Vin 5 *Enable 3 Undervoltage Lockout Enable Control Over-Temp. PWM Controller Indefinite Short-circuit Opto Isolation Over-Voltage Over-Load Error Amplifier 10 (-)Vout Trim* *Enable & Trim pin can be left floating if not used. Product Numbering System & Selection Guide MH 150 S TS Series No. Power No Input Voltage Range Voltage Options MH 100 : 100W S : Single 12 : 10-20V 12 : 12V C : Extended Temp. 150 : 1 24 : 1-36V 15 : 15V MC : Encapsulated 200 : 200W 4 : 36-5V 24 : 24V N : Negative Enable 300 : 300W 30 : 10-32V 2 : 2V TS : Chassis Mount 400 : 400W 60 : 20-60V 4 : 4V ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 4 of 15

5 Open Frame (Standard) 0.1 (4.32) MH Series, Single W 2.4 (2.2) 0.1 (4.32) Ø, 4 PLACES (11.2) max 2.4 (2.2) 2.25 (5.2) 0.3 (.5) 0.50 (19.05) (9.525) 0 (9.525) 0.50 (19.05) 5 - Vin(-) 4 - Vin(-) 3 - Enable 2 - Vin(+) 1 - Vin(+) V Rtn V Out *6 1. Pin 3 is (1.0mm) dia. 2. All other pins are (1.52mm) dia. with 0.05 (2.16mm) dia standoff shoulders. *9 Trim - 10 * Pins 6, 9 will be added on next revision and will be connected internally to pins and respectively. (Please make provisions on your design) 0.50 (19.05) (9.525) 0 (9.525) 0.50 (19.05) 0.15 (3.) min Encapsulated (Optional, MC Suffix) Chassis Mount (Optional, TS Suffix) 0.25 (6.4) 0.25 (6.4) 5 - Vin(-) 4 - Vin(-) V Rtn *6 5 4 Vin(-) Vin(-) V Rtn * (5.2) 3 - Enable 2 - Vin(+) V Out *9 4 SPACES (9.525) EACH 2.25 (5.2) 3 2 Enable Vin(+) V Out *9 1 - Vin(+) Trim Vin(+) Trim 10 (9.5) 1. Pin 3 is (1.0mm) dia. 2. All other pins are (1.52mm) dia. * Pins 6, 9 will be added on next revision and will be connected internally to pins and respectively. (Please make provisions on your design) (9.5) * Pins 6, 9 will be connected intternally to pins and respectively on next revision 0.53 (13.5) max (0.5) Encapsulated (MC Suffix) 0.9 (25) max. Chassis Mount (TS Suffix) #4-40 TAP, 4 PLACES. #4-40 TAP, 4 PLACES. ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 5 of 15

6 Range Designator (Range) 12 (10-20) 30 (10-32) 24 (1-36) MH Series, Single W INPUT OUTPUT Over Voltage (V) Current (A) Ripple & Noise Temp. EFF. UVL OVP Power Short Set OVP Circuit Shutdown (typ.) (On/Off) (Max) (Watts) Min.* Max.* Min. Max. Peak-Peak R.M.S. Point /Recover MODEL NO. 12V mV 15mV 15V % MH100S V mV 20mV 1V % MH100S V mV 30mV 2V +105/+95 C 90% MH100S1224 2V mV 40mV 33V 90% MH100S122 4V mV 60mV 5V 90% MH100S124 12V mV 15mV 15V % MH150S V mV 20mV 1V % MH150S V mV 30mV 2V +105/+95 C 90% MH150S1224 2V mV 40mV 33V 90% MH150S122 9.V/ 4V mV 60mV 5V 90% MH150S124 22V 9.5V 12V mV 15mV 15V % MH200S V mV 20mV 1V 9% MH200S V mV 30mV 2V +100/+90 C 90% MH200S1224 2V mV 40mV 33V 90% MH200S122 4V mV 60mV 5V 90% MH200S124 12V mV 15mV 15V % MH300S V mV 20mV 1V 90% MH300S V mV 30mV 2V +95/+5 C 90% MH300S1224 2V mV 40mV 33V 90% MH300S122 4V mV 60mV 5V 90% MH300S124 12V mV 15mV 15V % MH100S V mV 20mV 1V % MH100S V mV 30mV 2V +105/+95 C % MH100S3024 2V mV 40mV 33V % MH100S302 4V mV 60mV 5V % MH100S304 12V mV 15mV 15V % MH150S V mV 20mV 1V % MH150S V mV 30mV 2V +105/+95 C % MH150S3024 2V mV 40mV 33V % MH150S302 9.V/ 4V mV 60mV 5V % MH150S304 34V 9.5V 12V mV 15mV 15V % MH200S V mV 20mV 1V Hiccup % MH200S V mV 30mV 2V Mode +100/+90 C % MH200S3024 2V mV 40mV 33V Indefinite % MH200S302 4V mV 60mV 5V % MH200S304 12V mV 15mV 15V 6% MH300S V mV 20mV 1V 6% MH300S V mV 30mV 2V +95/+5 C % MH300S3024 2V mV 40mV 33V % MH300S302 4V mV 60mV 5V % MH300S304 12V mV 15mV 15V % MH100S V mV 20mV 1V % MH100S V mV 30mV 2V +105/+95 C 90% MH100S2424 2V mV 40mV 33V 90% MH100S242 4V mV 60mV 5V 90% MH100S244 12V mV 15mV 15V % MH150S V mV 20mV 1V % MH150S V mV 30mV 2V +105/+95 C 90% MH150S2424 2V mV 40mV 33V 90% MH150S242 4V mV 60mV 5V 90% MH150S244 12V mV 15mV 15V 90% MH200S V mV 20mV 1V 90% MH200S V/ 3V V mV 30mV 2V +100/+90 C 92% MH200S V 2V mV 40mV 33V 92% MH200S242 4V mV 60mV 5V 92% MH200S244 12V mV 15mV 15V 92% MH300S V mV 20mV 1V 92% MH300S V mV 30mV 2V +95/+5 C 94% MH300S1224 2V mV 40mV 33V 92% MH300S122 4V mV 60mV 5V 92% MH300S124 12V mV 15mV 15V 92% MH400S V mV 20mV 1V 92% MH400S V mV 30mV 2V +95/+5 C 94% MH400S2424 2V mV 40mV 33V 92% MH400S242 4V mV 60mV 5V 92% MH400S244 * Combined Line & Load Regulation (Low Line to High Line & Min. Load to Full Load) (Continued on Next Page ) ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 6 of 15

7 MH Series, Single W (Continued from Previous Page ) Range Designator (Range) 4 (36-5) 60 (20-60) INPUT OUTPUT Over Voltage (V) Current (A) Ripple & Noise Temp. EFF. UVL OVP Power Short Set OVP Circuit Shutdown (typ.) (On/Off) (Max) (Watts) Min.* Max.* Min. Max. Peak-Peak R.M.S. Point /Recover MODEL NO. 12V mV 15mV 15V 90% MH100S412 15V mV 20mV 1V 90% MH100S V mV 30mV 2V +105/+95 C 92% MH100S424 2V mV 40mV 33V 92% MH100S42 4V mV 60mV 5V 92% MH100S44 12V mV 15mV 15V 90% MH150S412 15V mV 20mV 1V 90% MH150S V mV 30mV 2V +105/+95 C 92% MH150S424 2V mV 40mV 33V 92% MH150S42 4V mV 60mV 5V 93% MH150S44 12V mV 15mV 15V 90% MH200S412 15V mV 20mV 1V 90% MH200S415 35V/34V 5V V mV 30mV 2V +100/+90 C 92% MH200S424 2V mV 40mV 33V 92% MH200S42 4V mV 60mV 5V 92% MH200S44 12V mV 15mV 15V 90% MH300S412 15V mV 20mV 1V 90% MH300S V mV 30mV 2V +95/+5 C 90% MH300S424 2V mV 40mV 33V 90% MH300S42 4V mV 60mV 5V 90% MH300S44 12V mV 15mV 15V 92% MH400S412 15V mV 20mV 1V 92% MH400S V mV 30mV 2V +95/+5 C 94% MH400S424 2V mV 40mV 33V 94% MH400S42 Hiccup 4V mV 60mV 5V 94% MH400S44 Mode 12V mV 15mV 15V % MH100S6012 Indefinite 15V mV 20mV 1V % MH100S V mV 30mV 2V +105/+95 C 90% MH100S6024 2V mV 40mV 33V 90% MH100S602 4V mV 60mV 5V 90% MH100S604 12V mV 15mV 15V % MH150S V mV 20mV 1V % MH150S V mV 30mV 2V +105/+95 C 90% MH150S6024 2V mV 40mV 33V 90% MH150S602 4V mV 60mV 5V 90% MH150S604 12V mV 15mV 15V % MH200S V mV 20mV 1V % MH200S V/ 62V V mV 30mV 2V +100/+90 C 90% MH200S V 2V mV 40mV 33V 90% MH200S602 4V mV 60mV 5V 90% MH200S604 12V mV 15mV 15V % MH300S V mV 20mV 1V % MH300S V mV 30mV 2V +95/+5 C 90% MH300S6024 2V mV 40mV 33V 90% MH300S602 4V mV 60mV 5V 90% MH300S604 12V mV 15mV 15V % MH400S V mV 20mV 1V % MH400S V mV 30mV 2V +95/+5 C 92% MH400S6024 2V mV 40mV 33V 92% MH400S602 4V mV 60mV 5V 92% MH400S604 * Combined Line & Load Regulation (Low Line to High Line & Min. Load to Full Load) ACON, INC. MH Series Rev. Jan. 2, 200 Pg. of 15

8 MH Series, Single W Efficiency Curves EFFICIENCY (%) Vin = 20V Vin = 4V Vin = 60V EFFICIENCY (%) Vin = 36V Vin = 60V Vin = 20V Current (A) MH100S4W MH300S Current (A) EFFICIENCY (%) Vin = 24V Vin = 36V Vin = 1V EFFICIENCY (%) Vin = 24V Vin = 36V Vin = 1V MH150S Current (A) Current (A) MH200S244 MH300S122 MH300S302 ACON, INC. MH Series Rev. Jan. 2, 200 Pg. of 15

9 INPUT Nominal (Range) 12 (10-20) 24 (1-36) 4 (36-5) 24W (10-30) 4W (1-36) UVLO On/Off 9./9.5 1/16 34/33 9./9.5 1/16 Power (Watt) MH Series, Dual 50 & Voltage (V) Current (A) Ripple & Noise OVP # Set (V) Point Min.* Max.* # Min. Max. Peak-Peak R.M.S. +V I mV 15mV V +V I mV 25mV +V I mV 15mV V +V I mV 30mV +V V +4.90V +5.10V +I mV 15mV V +V V I mV 25mV +V V +4.90V +5.10V +I mV 15mV V +V V +14.5V +15.5V +I mV 30mV +V I mV 15mV V +V I mV 25mV +V I mV 15mV V +V I mV 30mV +V V +4.90V +5.10V +I mV 15mV V +V V I mV 25mV +V V +4.90V +5.10V +I mV 15mV V +V V +14.5V +15.5V +I mV 30mV +V I mV 15mV V +V I mV 25mV +V I mV 15mV V +V I mV 30mV +V V +4.90V +5.10V +I mV 15mV V +V V I mV 25mV +V V +4.90V +5.10V +I mV 15mV V +V V +14.5V +15.5V +I mV 30mV +V I mV 15mV V +V I mV 25mV +V I mV 15mV V +V I mV 30mV +V V +4.90V +5.10V +I mV 15mV V +V V I mV 25mV +V V +4.90V +5.10V +I mV 15mV V +V V +14.5V +15.5V +I mV 30mV +V I mV 15mV V +V I mV 25mV +V I mV 15mV V +V I mV 30mV +V V +4.90V +5.10V +I mV 15mV V +V V I mV 25mV +V V +4.90V +5.10V +I mV 15mV V +V V +14.5V +15.5V +I mV 30mV * Combined Line & Load (Low Line to High Line, Min. Load to Full Load) Short Circuit Hiccup Mode Indefinite Over Temp. Shutdown /Recover +105 C/ +95 C EFF. (typ.) MODEL NO. 4% MH50D % MH50D % MH5D % MH5D % MH50D % MH50D % MH5D % MH5D % MH50D % MH50D % MH5D % MH5D % MH50D24W % MH50D24W % MH5D24W % MH5D24W % MH50D4W05+12 % MH50D4W % MH5D4W05+12 % MH5D4W05+12 Product Numbering System & Selection Guide MH 50 D MC Series No. Power No Input Voltage V1 V2/V3 Options MH 50 : D : Dual 12 : 10-20V 05 : 5.0V +12 : +12V C : -55 C Operation 5 : 24 : 1-36V +15 : +15V MC : Metal Case 4 : 36-5V TS : Terminal Strip 24W : 10-36V 4W : 20-5V ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 9 of 15

10 MH Series, Dual 50 & BLOCK DIAGRAM (+)Vin 3 Regulator for +12Vout only Low Dropout Regulator (+)V2 6 N.C. 9 (+)V1 (-)Vin 2 Undervoltage Lockout Over-Voltage Opto PWM Isolation *Enable Error 1 Enable Control Controller Amplifier 10 Trim* Over-Temp. Indefinite Short-circuit *Enable & Trim pin can be left floating if not used. Over-Load Com ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 10 of 15

11 Open Frame (Standard) 0.1 (4.32) MH Series, Dual 50 & 2.4 (2.14) 0.1 (4.32) Ø, 4 PLACES. N.C Vin(-) (+)V (50.) 1.60 (40.64) 3 - Vin(+) 2 - N.C. Com - (+)V1-9 4 SPACES (9.525) EACH 1 - Enable Trim (5.0) 0.35 (.9) max 1. All pins are (1.52mm) dia. with 0.05 (2.16mm) dia. standoff shoulders. 2. Tolerances: x.xx in. ±0.01 in. (0.25 mm) x.xxx in. ±0.005 in. (0.13 mm) 0.15 (3.) typ. Encapsulated (Optional, MC Suffix) Chassis Mount (Optional, TS Suffix) 0.25 (6.4) 0.25 (6.4) N.C N.C. N.C Vin(-) (+)V2-4 Vin(-) (+)V (5.2) 3 - Vin(+) 2 - N.C. Com - (+)V1-9 4 SPACES (9.525) EACH 2.25 (5.2) 3 2 Vin(+) N.C. Com (+)V Enable Trim Enable Trim 10 (9.5) All pins are (1.52mm) dia. (9.5) (1.52) 0.53 (13.5) max (0.5) Encapsulated (MC Suffix) 0.9 (25) max. Chassis Mount (TS Suffix) #4-40 TAP, 4 PLACES. #4-40 TAP, 4 PLACES. ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 11 of 15

12 INPUT OUTPUT Over Voltage (V) Current (A) Ripple & Noise Temp. UVLO Power OVP Short Shutdown (Watt) (V) Circuit # Set Point Min.* Max.* # Min. Max. Peak-Peak R.M.S. On/Off /Recover 9./9.5 +V I mV 15mV 5.9 +V I mV 25mV -V I mV 25mV +V I mV 15mV 5.9 +V I mV 30mV -V I mV 30mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V I mV 25mV -V3-12.0V I mV 25mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V +14.5V +15.5V +I mV 30mV -V3-15.0V -14.5V -15.5V +I mV 30mV 1/16 +V I mV 15mV 5.9 +V I mV 25mV -V I mV 25mV +V I mV 15mV 5.9 +V I mV 30mV -V I mV 30mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V I mV 25mV -V3-12.0V I mV 25mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V +14.5V +15.5V +I mV 30mV -V3-15.0V -14.5V -15.5V +I mV 30mV 34/33 +V I mV 15mV 5.9 +V I mV 25mV -V I mV 25mV +V I mV 15mV 5.9 +V I mV 30mV Hiccup -V I mV 30mV +105 C/ Mode +V V +4.90V +5.10V +I mV 15mV C Indefinite +V V I mV 25mV -V3-12.0V I mV 25mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V +14.5V +15.5V +I mV 30mV -V3-15.0V -14.5V -15.5V +I mV 30mV 9./9.5 +V I mV 15mV 5.9 +V I mV 25mV -V I mV 25mV +V I mV 15mV 5.9 +V I mV 30mV -V I mV 30mV +V V I mV 15mV 5.9 +V V I mV 25mV -V3-12.0V -11.5V -12.5V +I mV 25mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V +14.5V +15.5V +I mV 30mV -V3-15.0V -14.5V -15.5V +I mV 30mV 1/16 +V I mV 15mV 5.9 +V I mV 25mV -V I mV 25mV +V I mV 15mV 5.9 +V I mV 30mV -V I mV 30mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V I mV 25mV -V3-12.0V I mV 25mV +V V +4.90V +5.10V +I mV 15mV 5.9 +V V +14.5V +15.5V +I mV 30mV -V3-15.0V -14.5V -15.5V +I mV 30mV Nominal (Range) 12 (10-20) 24 (1-36) 4 (36-5) 24W (10-30) 4W (1-36) * Combined Line & Load (Low Line to High Line, Min. Load to Full Load) MH Series, Triple 50 & EFF. (typ.) MODEL NO. 4% MH50T % MH50T % MH5T % MH5T % MH50T % MH50T % MH5T % MH5T % MH50T % MH50T % MH5T % MH5T % MH50T24W05-12 % MH50T24W % MH5T24W05-12 % MH5T24W % MH50T4W05-12 % MH50T4W % MH5T4W05-12 % MH5T4W05-12 ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 12 of 15

13 MH Series, Triple 50 & BLOCK DIAGRAM Regulators for out only Low Dropout Regulator (+)V2 (+)Vin 3 Low Dropout Regulator 6 9 (-)V3 (+)V1 (-)Vin 2 Undervoltage Lockout Over-Voltage Opto PWM Isolation *Enable Error 1 Enable Control Controller Amplifier 10 Trim* Over-Temp. Indefinite Short-circuit *Enable & Trim pin can be left floating if not used. Over-Load Com 12.5 Cross Regulation ( vs Load) 16.0 Cross Regulation ( vs Load) (V) V or 0.05A +12V or 1.0A +12V or 2.0A (V) V or 0.05A +15V or 1.0A +15V or 2.0A Loading (A) Loading (A) Product Numbering System & Selection Guide MH 50 T MC Series No. Power No Input Voltage V1 V2/V3 Options MH 50 : T : Triple 12 : 10-20V 05 : 5.0V -12 : C : -55 C Operation 5 : 24 : 1-36V -15 : MC : Metal Case 4 : 36-5V TS : Terminal Strip 24W : 10-36V 4W : 20-5V ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 13 of 15

14 Open Frame (Standard) 0.1 (4.32) MH Series, Triple 50 & 2.4 (2.14) 0.1 (4.32) Ø, 4 PLACES. (-)V Vin(-) (+)V (50.) 1.60 (40.64) 3 - Vin(+) 2 - N.C. Com - (+)V1-9 4 SPACES (9.525) EACH 1 - Enable Trim (5.0) 0.35 (.9) max 1. All pins are (1.52mm) dia. with 0.05 (2.16mm) dia. standoff shoulders. 2. Tolerances: x.xx in. ±0.01 in. (0.25 mm) x.xxx in. ±0.005 in. (0.13 mm) 0.15 (3.) typ. Metal Case (Optional, MC Suffix) Chassis Mount (Optional, TS Suffix) 0.25 (6.4) 0.25 (6.4) (-)V3-6 5 N.C. (-)V Vin(-) (+)V2-4 Vin(-) (+)V (5.2) 3 - Vin(+) 2 - N.C. Com - (+)V1-9 4 SPACES (9.525) EACH 2.25 (5.2) 3 2 Vin(+) N.C. Com (+)V1 9 1 Enable *Trim 10 (9.5) (9.5) 0.53 (13.5) max. 1 - Enable (0.5) Trim - 10 Encapsulated (MC Suffix) 0.9 (25) max. Chassis Mount (TS Suffix) #4-40 TAP, 4 PLACES. #4-40 TAP, 4 PLACES. ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 14 of 15

15 Efficiency Curve 95 EFFICIENCY vs LOAD MH Series, Triple 50 & Transient Response EFFICIENCY (%) Vin = 1V Vin = 24V Vin = 36V LOAD (%) MH5T EFFICIENCY vs LOAD EFFICIENCY (%) Vin = 24V Vin = 36V Vin = 10V LOAD (%) MH5T24W EFFICIENCY vs LOAD EFFICIENCY (%) Vin = 4V Vin = 5V Vin = 1V LOAD (%) MH5T4W V -12V ACON, INC. MH Series Rev. Jan. 2, 200 Pg. 15 of 15

200 WATT TH SERIES DC/DC CONVERTERS

200 WATT TH SERIES DC/DC CONVERTERS Features 4:1 Input voltage range High power density Small size 2.4 x 2.28 x 0.65 Efficiency up to 90 Excellent thermal performance with metal case Pulse-by-pulse current limiting Over-temperature protection

More information

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output

DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output THN 20WI Series Application Note DC/DC Converter 9 to 36Vdc and 18 to 75Vdc input voltage, 20 Watt Output Power; 3.3 to 15Vdc Single Output and ±12Vdc to ±15Vdc Dual Output Pending Applications Wireless

More information

STB Series 2:1 & 4:1 Vin range / up to 60W 1/16 Brick

STB Series 2:1 & 4:1 Vin range / up to 60W 1/16 Brick 2:1 & 4:1 Vin range / up to W 1/16 Brick Features Industry-Standard DOSA pin out 4:1 / 2:1 Ultra-Wide input range High Ffficiency 91%@ 5V (SR topology) Compact size 1.49 x 1.46 x.5 Metal Case Six-Sided

More information

ESB Series Embedded EMC Filter Up to 40W converter

ESB Series Embedded EMC Filter Up to 40W converter Features High Ffficiency up to 91% 2:1 / 4:1 Ultra-Wide input range Compact size 1.6 x 1.0 x 0.4 & 1.6 x 1.0 x 0.5 Standard DOSA pin out; Fully replaceable with 2 x1 standard case Metal Case Six-Sided

More information

Note1: Measured at nominal input voltage and full load Note2: Measured at minimum input voltage and constant resistive load

Note1: Measured at nominal input voltage and full load Note2: Measured at minimum input voltage and constant resistive load Features Regulated Converters Description :1 wide input voltage range 1.kV isolation UL certified Efficiency up to 88% Fixed operating frequency Six-Sided continuous shield No minimum load required The

More information

AA SERIES (1 x 1 Package) Up to 10 Watt DC-DC Converter

AA SERIES (1 x 1 Package) Up to 10 Watt DC-DC Converter FEATURES Industry standard footprint (1 inch X 1 inch) Regulated Outputs, Fixed Switching Frequency Up to 87 % Efficiency Low No Load Power Consumption Designed for use without tantalum capacitors -40

More information

AA SERIES (1 x 1 Package) Up to 30 Watt DC-DC Converter

AA SERIES (1 x 1 Package) Up to 30 Watt DC-DC Converter FEATURES Industry standard footprint (1 inch X 1 inch) Regulated Outputs, Fixed Switching Frequency Up to 90 Efficiency Low No Load Power Consumption Designed for use without tantalum capacitors -40 C

More information

15 W DC/DC CONVERTERS. SERIES DESCRIPTION Page. PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation

15 W DC/DC CONVERTERS. SERIES DESCRIPTION Page. PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation 15 W DC/DC CONVERTERS SERIES DESCRIPTION Page PC15WR 2:1 Input Range 2 2 x 1 Metal Can Package 2kv Isolation PC15WR4 4:1 Input Range 6 2 x 1 Metal Can Package 2kv Isolation CTC TECHNOLOGY CO.,LTD. DC /

More information

RPP20-W. Features ICE Technology* POWERLINE+ 20 Watt 4:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty

RPP20-W. Features ICE Technology* POWERLINE+ 20 Watt 4:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty Features ICE Technology* Description 115 C Maximum Case Temperature -40 C Minimum Temp. UL Certified Built-in FCC/EN55022 Class B Filter 4:1 Wide Input Voltage Range Six Sided Shielded Enclosure Ribbed

More information

Ripple & Max. capacitive Output Current

Ripple & Max. capacitive Output Current 0 Watts xxx Series Wide 4: Input Range Single Output Industry Standard /4 Brick -40 C to +0 C Operation 0 VDC Isolation Output Trim ±0% Remote On/Off Year Warranty Dimensions: QSC0:. x.4 x 0. (.9 x. x.

More information

PM24S/DR24S series 60W Single Output DC/DC Converter

PM24S/DR24S series 60W Single Output DC/DC Converter FEATURES Efficiency up to 92% Wide input range, 9V-36V Package Dimension: Panel Mount: 100.0*56.0*19.0mm (3.94 * 2.20 *0.75 ) Din Rail: 118.6*67.1*23.5mm (4.67 *2.64 *0.93 ) Over voltage protection, hiccup

More information

(typ.) (Range) Parameter Model Min. Typ. Max. Unit

(typ.) (Range) Parameter Model Min. Typ. Max. Unit FEATURES Smallest Encapsulated 20W! Package Size 1.0 x1.0 x0.4 Ultra-wide 4:1 Input Range Very high Efficiency up to % Operating Temp. Range - C to +85 C Output Voltage Trimmable I/O-isolation Voltage

More information

PM24S/PM24D series 30W Single/Dual Output DC/DC Converter

PM24S/PM24D series 30W Single/Dual Output DC/DC Converter FEATURES Efficiency up to 88% Wide input range, 9V-36V Package Dimension: Panel Mount: 100.0*56.0*19.0mm (3.94 * 2.20 *0.75 ) Din Rail: 118.6*67.1*23.5mm (4.67 *2.64 *0.93 ) Over voltage protection, hiccup

More information

Notes: Note1: Max. capacitive load is tested at nominal input voltage and full load. Single or Dual

Notes: Note1: Max. capacitive load is tested at nominal input voltage and full load. Single or Dual Features Regulated Converters Description 6-Side Shielding External ON/OFF control 1.6kV Isolation UL/CSA/EN-695-1 Certified 2:1 Input Voltage Range Continuous Short Circuit Protection Efficiency up to

More information

PRODUCT OVERVIEW. APPLICATIONS: Distributed Power Architectures Mobile telecommunication Industrial applications Battery operated equipment

PRODUCT OVERVIEW. APPLICATIONS: Distributed Power Architectures Mobile telecommunication Industrial applications Battery operated equipment FEATURES Industry Standard 24-Pin DIP package 15Watts Isolated Output 4:1 Input Range Regulated Outputs Up to 90 % Efficiency Low No Load Power Consumption -40 C to +85 C industrial temperature range Negative

More information

SIL20C SERIES. Single Output. SIL20C Series 20 A DC-DC Converter C Class Non-Isolated

SIL20C SERIES. Single Output. SIL20C Series 20 A DC-DC Converter C Class Non-Isolated SIL20C SERIES Single Output Wide output voltage trim (0.9 Vdc to 5.0 Vdc, 20 A max.) Power good output signal (open collector) Input undervoltage lockout Current sink capability for termination applications

More information

SIL20C2 Series Single Output

SIL20C2 Series Single Output SIL20C2 Series 20 A DC-DC SIL20C2 Series Single Output Adjustable output voltage (0.59-5.1 V, 20 A max.) Power good output signal (open collector) Input undervoltage lockout Current sink capability for

More information

TB65 65W Single Output Test and Measurement/Industrial Series

TB65 65W Single Output Test and Measurement/Industrial Series Features 2.0 x 3.5 x 1.3 Package TB65 Up to 65W Convection Cooled Output Power Compliant to high levels of EMC per EN61000-4 15kV ESD (Air), 8kV (Contact) 4kV Surge Meets Class B Conducted EMI with 6db

More information

MIW3000 Series EMI. 5-6W, Wide Input Range DIP, Single & Dual Output DC/DC Converters MINMAX. Block Diagram. Key Features

MIW3000 Series EMI. 5-6W, Wide Input Range DIP, Single & Dual Output DC/DC Converters MINMAX. Block Diagram. Key Features -6W, Wide Input Range DIP, Single & DC/DC s Key Features Efficiency up to 10 Isolation MTBF > 1,000,000 Hours 2:1 Wide Input Range UL19 Safety Approval Complies with EN22 Class A Temperature Performance

More information

OVP 2:1. Wide Range. Protection

OVP 2:1. Wide Range. Protection 10W, Wide Input Range DIP, Single & Dual Output DC/DC s Key Features High Efficiency up to 88 10 Isolation MTBF > 1,000,000 Hours 2:1 Wide Input Range CSA9-1 Safety Approval Complies with EN522 Class A

More information

RPP30. Features ICE Technology* POWERLINE+ 30 Watt 2:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty

RPP30. Features ICE Technology* POWERLINE+ 30 Watt 2:1 Single & Dual Output. DC/DC-Converter with 3 year Warranty Features ICE Technology* Description 115 C Maximum Case Temperature -40 C MinimumTemp. Built-in FCC/EN55022 Class B Filter 2:1 Wide Input Voltage Range Six Sided Shielded Enclosure Ribbed or Baseplate

More information

SMT20C SERIES. Single Output TÜV. SMT20C Series 20 A DC-DC Converter C Class Non-Isolated

SMT20C SERIES. Single Output TÜV. SMT20C Series 20 A DC-DC Converter C Class Non-Isolated SMT20C SERIES Single Output Wide output voltage trim (0.9 Vdc to 5.0 Vdc, 20 A max.) Power good output signal (open collector) Input undervoltage lockout Current sink capability for termination applications

More information

DC Output Voltage range: 5 to 50VDC Current range: 0 to 40A Power range: 0 to 500W Peak power: Up to 750W for up to 4 seconds.

DC Output Voltage range: 5 to 50VDC Current range: 0 to 40A Power range: 0 to 500W Peak power: Up to 750W for up to 4 seconds. M7027 SERIES MINIATURE, SINGLE OUTPUT VERY HIGH DENSITY, DC / DC CONVERTERS Up to 500 W (750 W peak) Applications Military (Airborne, ground-fix, shipboard), Ruggedized, Telecom, Industrial Special Features

More information

Features. Power Module. 2 Amp Single Output RBB RBB DC/DC Converter

Features. Power Module. 2 Amp Single Output RBB RBB DC/DC Converter Features Power Module 1W buck/boost converter with up to 4A output Input voltage can be higher, lower or same as output voltage >9% efficiency from 1mA 3mA load 7µA standby power consumption Low profile,

More information

The 0RQB-C5U54x is an isolated DC-DC converter that operates from a nominal 24 VDC, 48 VDC source.

The 0RQB-C5U54x is an isolated DC-DC converter that operates from a nominal 24 VDC, 48 VDC source. The 0RQB-C5U54x is an isolated DC-DC converter that operates from a nominal 24 VDC, 48 VDC source. This unit will provide up to 162 W of output power from a nominal 24 VDC, 48 VDC input. This unit is designed

More information

PXD30-xxWS-xx-Single Output DC/DC Converters

PXD30-xxWS-xx-Single Output DC/DC Converters PXD30-xxWS-xx-Single Output DC/DC Converters 9 to 36 Vdc and 18 to 75 Vdc input, 1.5 to 15 Vdc Single Output, 30W Applications Wireless Network Telecom / Datacom Industry Control System Measurement Semiconductor

More information

150 WATT QSW DC/DC CONVERTERS

150 WATT QSW DC/DC CONVERTERS Description The 4:1 Input Voltage 150 Watt Single QSW DC/DC converter provides a precisely regulated dc output. The output voltage is fully isolated from the input, allowing the output to be positive or

More information

DVETR2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS WITH INTEGRAL EMI FILTER DESCRIPTION FEATURES

DVETR2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS WITH INTEGRAL EMI FILTER DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS WITH INTEGRAL EMI FILTER DESCRIPTION The DVETR series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range

More information

SXN15 48V SERIES. Dual output TÜV. High Efficiency DC/DC Converters

SXN15 48V SERIES. Dual output TÜV. High Efficiency DC/DC Converters SXN15 48V SERIES Dual output High efficiency topology, 86% typical at 5V/3.3V Wide operating temperature, up to and exceedingly 65ºC (natural convection) 9% to 11% output trim No minimum load Overvoltage

More information

60 Watt Triple Output Half Brick DC/DC Converter

60 Watt Triple Output Half Brick DC/DC Converter VKP60xT Corporate: Corporate: www.cdtechno.com www.cdtechno.com 60 Watt Triple Output Half Brick DC/DC Converter 18-40 & 33-75V Input Range Each Channel Independently Current Limited High Efficiency: 87%

More information

Efficiency (typ.) (Range) Load. Output Current Input Current Reflected Ripple

Efficiency (typ.) (Range)  Load. Output Current Input Current Reflected Ripple FEATURES Highest Power Density 1" x 1" x 0.4" Shielded Metal Package Ultra Wide 4:1 Input Range Excellent Efficiency up to % Operating Temp. Range - C to + C Optional Heatsink I/O-isolation Voltage 10VDC

More information

XD50-24S28-POCW Technical Specification

XD50-24S28-POCW Technical Specification Key Features Package: Open Frame Small footprint: 2.08 1.48 0.38in 52.8 37.6 9.7mm Product Overview These DC-DC converter modules use advanced power processing, control and packaging technologies to provide

More information

500 WATT MXW SERIES DC/DC CONVERTERS

500 WATT MXW SERIES DC/DC CONVERTERS 4:1 Input voltage range High power density Small size 2.4 x 2.5 x 0.52 Efficiency up to 95.7% Excellent thermal performance with metal case Over-Current and Short Circuit Protection Over-Temperature protection

More information

Cool Power Technologies

Cool Power Technologies Cool Power Technologies Sixteenth-Brick Isolated DC/DC Converter Features Industry-standard pinout Wide input voltage range: 36 75Vin Output: 3.3 V at 12 A, 40W max. No minimum load required Low height

More information

Encapsulated Power Supply

Encapsulated Power Supply 0 Watt Features AC/DC Power Modules PCB Mounting or Chassis Mounting with Screw Terminals Fully encapsulated Plastic Case Single, Dual and Triple Output Models Universal Input 8- VAC, 7-0 Hz High Efficiency

More information

360 WATT MTW SERIES DC/DC CONVERTERS

360 WATT MTW SERIES DC/DC CONVERTERS Description The 4:1 Input Voltage 360 Watt Single MTW DC/DC converter provides a precisely regulated dc output. The output voltage is fully isolated from the input, allowing the output to be positive or

More information

Note1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage.

Note1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage. Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Ribbed Case Style 22VDC Isolation Built-in EMC Filter, EN-522 Class B The RPP20 series

More information

S24SP12004 series 40W Single Output DC/DC Converter

S24SP12004 series 40W Single Output DC/DC Converter FEATURES Efficiency up to 92.8% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: Without heat sink 5.8 x25.4 x1.5mm (2. x1. x.41 ) With heat sink 5.8 x25.4 x17.5mm (2.

More information

S24SP05012 series 60W Single Output DC/DC Converter

S24SP05012 series 60W Single Output DC/DC Converter Model List Model Number S24SP05012 Input Voltage (Range) Output Voltage Output Current Input Current (typ input voltage) Load Regulation Maxcapacitive Load (Cap ESR>=10mohm;Full Efficiency load;5%overshoot

More information

9 to 36 Vdc and 18 to 75 Vdc input, 3.3 to 15 Vdc Single Output, 40W. Features

9 to 36 Vdc and 18 to 75 Vdc input, 3.3 to 15 Vdc Single Output, 40W. Features PXF40xxWSxx Single Output DC/DC Converter 9 to 36 Vdc and 18 to 75 Vdc input, 3.3 to 15 Vdc Single Output, 40W Features Single output current up to 10A 40 watts maximum output power 4:1 ultra wide input

More information

S24SP24003 series 60W Single Output DC/DC Converter

S24SP24003 series 60W Single Output DC/DC Converter FEATURES Efficiency up to 93% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: Without heat sink 5.8 x25.4 x1.5mm (2. x1. x.41 ) With heat sink 5.8 x25.4 x17.5mm (2. x1.

More information

Features. Regulated Converter. REM10 10 Watt. 2:1 & 4:1 DIP24 Single and Dual Output REM10- / DC/DC Converter

Features. Regulated Converter. REM10 10 Watt. 2:1 & 4:1 DIP24 Single and Dual Output REM10- / DC/DC Converter Features Regulated Converter Description Reinforced insulation for 250VAC working voltage Clearance and creepage distance: 8mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard

More information

Distributing Tomorrow s Technologies For Today s Designs Toll-Free:

Distributing Tomorrow s Technologies For Today s Designs Toll-Free: 3W, Wide Input Range DIP, Single & DC/DC s Key Features Efficiency up to 82 Isolation MTBF > 1,000,000 Hours 2:1 Wide Input Range Low Cost Complies with EN022 Class A Temperature Performance -2 to +71

More information

S24SE/S24DE series 30W Single/Dual Output DC/DC Converter

S24SE/S24DE series 30W Single/Dual Output DC/DC Converter FEATURES Efficiency up to 89% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: 25.4 x25.4 x10.2mm (1.0 x1.0 x0.40 )(No HSK) Over voltage protection, hiccup mode Over current

More information

Note1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage.

Note1: Typical values at nominal input voltage and full load. 17.5VDC. Open, 4.5V Short, 0V. 5mA. Efficiency vs. Input Voltage. Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Ribbed Case Style 22VDC Isolation Built-in EMC Filter, EN-522 Class B The RPP20 series

More information

Ordercode Output Power Output 1 Output 2 Output 3 PCB-mounting Chassis mounting max. with solder pins with screw terminals

Ordercode Output Power Output 1 Output 2 Output 3 PCB-mounting Chassis mounting max. with solder pins with screw terminals Features PCB Mounting with Solder Pins or Chassis Mounting with Screw Terminals Single, Dual and Triple Output Models Universal Input 8-2 VAC, 0 0 Hz EMI meets EN 022, Class B and FCC, Level B Low Ripple

More information

Add suffix /W/X3 for wired version with both analogue and PWM dimming controls (six wires) (a)

Add suffix /W/X3 for wired version with both analogue and PWM dimming controls (six wires) (a) Features Regulated Converters Selection Guide UL/ RAILWAYS Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature

More information

(DOSA) VDC, 5.5 A.

(DOSA) VDC, 5.5 A. Features Industry-standard pinout Output: 15 V at 5.5 A, 82.5W max. No minimum load required Low height - 0.374 (9.5mm) max. Basic Insulation Withstands 100 V input transients Fixed-frequency operation

More information

Features. Regulated Converters. RS6 6 Watt. SIP8 Single and Dual Output. DC/DC Converter. Description. Selection Guide

Features. Regulated Converters. RS6 6 Watt. SIP8 Single and Dual Output. DC/DC Converter. Description. Selection Guide Features Regulated Converters Description Highest Power Density In SIP Package 1.6kVDC/1 Minute Isolation Efficiency Up To 88% -4 C To +75 C Operating Temperature Range @ Full Load EN695 And UL/EN62368-1

More information

Pinning (3) 4:1 Input Single or Dual. Notes: Note3: /X2 is without ON/OFF CTRL and without Output Voltage Trimming

Pinning (3) 4:1 Input Single or Dual. Notes: Note3: /X2 is without ON/OFF CTRL and without Output Voltage Trimming Features Regulated Converters 4:1 wide input voltage range Compact size 1 x1 package Efficiency up to % Wide operating temperature from - C to +75 C without derating Continuous short circuit protection

More information

DVSA2800S Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES

DVSA2800S Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVSA series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range with no power derating.

More information

DVTR2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES

DVTR2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVTR series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range with no power derating.

More information

S24SE/S24DE series 30W Single/Dual Output DC/DC Converter

S24SE/S24DE series 30W Single/Dual Output DC/DC Converter Model List Model Number Input Voltage Output Voltage Output Current Input Current (typ input voltage) (Range) Max. Min. @Max. Load @No Load Load Regulation Maxcapacitive Efficiency Load (typ.) @Max. Load

More information

Networking Computers and Peripherals Telecommunications

Networking Computers and Peripherals Telecommunications The 0RCY-60U12x is part of the isolated DC/DC converters that operate from a wide input range (18 VDC - 75 VDC) and can cover both 24 Vin and 48 Vin input range. These units will provide up to 84 W of

More information

Efficiency (typ.) (Range) Load VDC VDC ma ma(typ.) ma(typ.) μf % MCWI05-12S

Efficiency (typ.) (Range)  Load VDC VDC ma ma(typ.) ma(typ.) μf % MCWI05-12S FEATURES Smallest Encapsulated 5W Ultracompact SIP8 Package Ultrawide 4 : 1 Input Voltage Range Fully Regulated Output Voltage I/O Isolation 1500 VDC Operating Ambient Temp. Range40 to 75 No Min. Requirement

More information

DN03S/D Series DC/DC CONVERTER 2-3W, DIP-Package

DN03S/D Series DC/DC CONVERTER 2-3W, DIP-Package DN03S/D Series DC/DC CONVERTER 2-3W, DIP-Package FEATURES DIP-24 Plastic Package Wide 2:1 Input Range Operating Temp.Range -40 to +85 C Overload Protection No Minimum Load Requirement Isolation voltage

More information

Output Voltage Output Amps Input Range Max. Iin FL Efficiency (Tb=25 C) O/P Set Point

Output Voltage Output Amps Input Range Max. Iin FL Efficiency (Tb=25 C) O/P Set Point Miniature 4.59 x 2.4 x 0.5. Size High Power Density up to 90.78W/ Inch ³ High Efficiency up to 90.5% at 230VAC (28V) Low Output Noise Metal Baseplate Thermal Protection Over Voltage Protection Current

More information

DVHV2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES

DVHV2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES The DVHV series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range with no power derating.

More information

Features. Regulated Converter. REM6 6 Watt 2:1 & 4:1 DIP24 Single and Dual. Output. DC/DC Converter

Features. Regulated Converter. REM6 6 Watt 2:1 & 4:1 DIP24 Single and Dual. Output. DC/DC Converter Features Regulated Converter Reinforced insulation for 250VAC working voltage Clearance and creepage distance: 8mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout

More information

QUARTER-BRICK SERIES Single Output Performance Products

QUARTER-BRICK SERIES Single Output Performance Products Quarter-Brick Series 100 A DC-DC QUARTER-BRICK SERIES Single Output Performance Products High efficiency topology High output current Low profile, 0.300 inch (7.62 mm) height Unprecedented useable output

More information

DVCH2800S Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES

DVCH2800S Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVCH series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range with no power derating.

More information

Features. Unregulated Converters. 1 Watt SIP6 Micro Size, Single and Dual Output RBM. RBM- / Protection (3) Single or Dual.

Features. Unregulated Converters. 1 Watt SIP6 Micro Size, Single and Dual Output RBM. RBM- / Protection (3) Single or Dual. Features Unregulated Converters Micro size SIP 6 package Industry standard pinout Power sharing on dual output version 3kVDC/1s basic isolation Optional continuous short circuit protection Efficiency up

More information

S24SE/S24DE series 15W Single/Dual Output DC/DC Converter

S24SE/S24DE series 15W Single/Dual Output DC/DC Converter FEATURES Efficiency up to 89% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: 25.4 x25.4 x10.2mm (1.0 x1.0 x0.40 )(No HSK) Over voltage protection, hiccup mode Over current

More information

SRPE-50E1A0 Non-Isolated DC-DC Converter

SRPE-50E1A0 Non-Isolated DC-DC Converter SRPE-50E1A0 Non-Isolated DC-DC Converter The Bel SRPE-50E1A0 is part of the non-isolated dc to dc converter Power Module series. The modules use a Vertical SMT package. These converters are available in

More information

DVSB2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES

DVSB2800D Series HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION FEATURES HIGH RELIABILITY HYBRID DC-DC CONVERTERS DESCRIPTION The DVSB series of high reliability DC-DC converters is operable over the full military (-55 C to +125 C) temperature range with no power derating.

More information

High power density 3W Converter in SIP7 case. 3kVDC and 4kVDC Isolation Options

High power density 3W Converter in SIP7 case. 3kVDC and 4kVDC Isolation Options Features Unregulated Converters Description High power density 3W Converter in SIP7 case 3kVDC and 4kVDC Isolation Options Efficiency to 9% Certified to IEC/EN62368 The series of 3W high isolation DC/DC

More information

Load (2) Single or Dual

Load (2) Single or Dual Features Regulated Converter Reinforced insulation for 2VAC working voltage Clearance and creepage distance >8.mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout 4:

More information

Note1: Max. capacitive load is tested at nominal input and constant resistive load. RI3- _/_ Isolation (2) Single

Note1: Max. capacitive load is tested at nominal input and constant resistive load. RI3- _/_ Isolation (2) Single Features Unregulated Converters 3 Watt in a SIP4 Package -3kVDC Isolation Efficiency up to 9% -4 C to + C Operating Temperature Range IEC/EN/UL69 (Pending) CB Report (Pending) Industry Standard Pinout

More information

Specifications ( typical at 25 C, nominal input voltage, rated output current unless otherwise specified )

Specifications ( typical at 25 C, nominal input voltage, rated output current unless otherwise specified ) Features Regulated Converters Description UL Certified Constant Current LED Driver Wide Input and Output Voltage Range Digital PWM and Analogue Voltage Dimming Short Circuit and Overtemperature Protected

More information

Distributing Tomorrow s Technologies For Today s Designs Toll-Free:

Distributing Tomorrow s Technologies For Today s Designs Toll-Free: 2W, Wide Input Range DIP, Single & DC/DC s Key Features Efficiency up to 81 Isolation MTBF > 1,000,000 Hours 2:1 Wide Input Range CSA1 Safety Approval Low Ripple and Noise Short Circuit Protection Complies

More information

One part that covers many applications Reduces board space, system cost and complexity, and time to market. North America

One part that covers many applications Reduces board space, system cost and complexity, and time to market. North America Bel Power Solutions point-of-load converters are recommended for use with regulated bus converters in an Intermediate Bus Architecture (IBA). The YEV09T, non-isolated DC-DC point of load (POL) converter,

More information

0RQB-X3S11B(F) Isolated DC-DC Converter

0RQB-X3S11B(F) Isolated DC-DC Converter 0RQB-X3S11B(F) Isolated DC-DC Converter The 0RQB-X3S11B(F) is an isolated DC/DC converter that operates from a nominal 50/54 Vdc source. This converter is intended to provide isolation and step down to

More information

AS SERIES (2.00 x 1.6 Package) Up to 20 Watt DC-DC Converter

AS SERIES (2.00 x 1.6 Package) Up to 20 Watt DC-DC Converter PRODUCT OVERVIEW The AS series offer up to 20 watts of output power in standard 2.00 x 1.60 x 0.45 inches packages. This series features high efficiency and 1500 Volts of DC isolation. The AS series provides

More information

id id mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator Features General Description Applications

id id mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator Features General Description Applications 500mA, Low Dropout, Low Noise Ultra-Fast With Soft Start CMOS LDO Regulator General Description The is a 500mA, low dropout and low noise linear regulator with high ripple rejection ratio. It has fixed

More information

Series AM50E-NZ 50 Watt DC-DC Converter

Series AM50E-NZ 50 Watt DC-DC Converter FEATURES: Wide Input range 2:1 Input to Output Isolation of 1500 High Efficiency up to 93% Input Over Voltage and Under Voltage Lockout Remote On/Off Control Output OVP, OCP & SCP Trim Adjustment Operating

More information

Load (2) Single or Dual

Load (2) Single or Dual Features Regulated Converter Reinforced insulation for VAC working voltage Clearance and creepage distance >8.mm kvac I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout 4:

More information

PXD10-Single Output DC/DC Converter

PXD10-Single Output DC/DC Converter PXD10-Single Output DC/DC Converter 9 to 18 Vdc, 18 to 36 Vdc and 36 to 75 Vdc input, 3.3 to 15 Vdc Single Output, 10W Features Single output current up to 2A 10 watts maximum output power 2:1 wide input

More information

ISOLATED DC-DC CONVERTER CEB75 SERIES APPLICATION NOTE

ISOLATED DC-DC CONVERTER CEB75 SERIES APPLICATION NOTE ISOLATED DC-DC CONVERTER CEB75 SERIES APPLICATION NOTE Approved By: Department Approved By Checked By Written By Enoch Louis Joyce Research and Development Department Danny Quality Assurance Department

More information

H80SV12017 * * FEATURES. Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W APPLICATIONS

H80SV12017 * * FEATURES. Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W APPLICATIONS H80SV12017 200W DC/DC Power Modules Delphi Series H80SV, half Brick Family DC/DC Power Modules: 16.8~137.5 Vin, 54/48/24/15/12Vout,200W The H80SV series Half-Brick is isolated 200W DC/DC converters with

More information

LD7536R 05/11/2010. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features.

LD7536R 05/11/2010. Green-Mode PWM Controller with Frequency Swapping and Integrated Protections. General Description. Features. 05/11/2010 Green-Mode PWM Controller with Frequency Swapping and Integrated Protections Rev. 00 General Description The LD7536R is built-in with several functions, protection and EMI-improved solution

More information

S24SP series 60W Single Output DC/DC Converter

S24SP series 60W Single Output DC/DC Converter Model List Model Number Input Voltage (Range) Output Voltage Output Current Input Current (typ input voltage) Load Regulation Maxcapacitive Load (Cap ESR>=1mohm;Full Efficiency (typ.) load;5%overshoot

More information

ISOLATED DC-DC CONVERTER EC4SBW SERIES APPLICATION NOTE

ISOLATED DC-DC CONVERTER EC4SBW SERIES APPLICATION NOTE ISOLATED DC-DC CONVERTER EC4SBW SERIES APPLICATION NOTE Approved By: Department Approved By Checked By Written By Enoch Danny Eunice Research and Development Department Jacky David Benny Quality Assurance

More information

0RCY-F0S10x Isolated DC-DC Convert

0RCY-F0S10x Isolated DC-DC Convert 0RCY-F0S10x Isolated DC-DC Convert The 0RCY-F0S10x is an isolated DC/DC converter that operate from a nominal 50 V/54 V source. This converter is intended to provide isolation and step down to generate

More information

LDO03C SERIES. Single Output. LDO03C Series 3 A DC-DC C Class Non-Isolated DC/DC Converter [ 2 YEAR WARRANTY ]

LDO03C SERIES. Single Output. LDO03C Series 3 A DC-DC C Class Non-Isolated DC/DC Converter [ 2 YEAR WARRANTY ] LDO03C SERIES Single Output 3 A current rating Input voltage range 3-13.8 V Adjustable output voltage 0.59-5.1 V Optional 3-pin model factory set Optional 5-pin model factory set with power good option

More information

40 Watt TMF Single and Dual Series

40 Watt TMF Single and Dual Series Watt TMF Single and Dual Series Efficiency up to 91% 10VDC Isolation MTBF > 328,000 Hours 4:1 Wide Input Over Voltage Protection Short Circuit Protection Six Sided Shielding Remote On/Off Control RoHS

More information

Parameter Symbol Min Typ Max Unit Operating voltage Range Vin Vdc Input current at 36V. Iin - - A Input current at 55V

Parameter Symbol Min Typ Max Unit Operating voltage Range Vin Vdc Input current at 36V. Iin - - A Input current at 55V QPC20A NonIoslated Quater Brick Buck Converters Features Industry standard Quarterbrick 58.42mm x 36.83mm x 13mm (2.3in x 1.45in x 0.512in) High efficiency Single output Constant switching frequency Synchronous

More information

CV SERIES. 1.8 to 45 Watts VDC, VDC, 10-30VDC Input Ranges Adjustable Output Voltage Non-Isolated DC/DC Converters

CV SERIES. 1.8 to 45 Watts VDC, VDC, 10-30VDC Input Ranges Adjustable Output Voltage Non-Isolated DC/DC Converters DATASHEET CV SERIES 2.-.VDC, 4.-4VDC, 0-30VDC Input Ranges FEATURES Output Current up to 3A Output Power Range 2.-.VDC, 4.-4VDC, and 0-30VDC Input Voltage Ranges High Efficiency - 9% at 2VDC and Full Load

More information

EIGHTH-BRICK SERIES. Single Output Value Products. Special Features

EIGHTH-BRICK SERIES. Single Output Value Products. Special Features EIGHTH-BRICK SERIES Embedded Power for Business-Critical Continuity 1 of 31 EIGHTH-BRICK SERIES Total Power: 50 W Input Voltage: 36-75 VDC # of Outputs: Single Special Features High efficiency topology

More information

QUARTER-BRICK SERIES Single Output Value Products

QUARTER-BRICK SERIES Single Output Value Products Quarter-Brick Series 50 A DC-DC QUARTER-BRICK SERIES Single Output Value Products High efficiency topology High output current Low profile, 0.300 inch (7.62 mm) height Unprecedented useable output power

More information

Features. Switching Regulator. 0.5 Amp SIP3 Single Output R R DC/DC Converter

Features. Switching Regulator. 0.5 Amp SIP3 Single Output R R DC/DC Converter Features Switching Regulator Description Efficiency up to 97%, no need for heatsinks Pin-out compatible with LM78XX linears Very low profile 4.75V - 32V Wide input range Short circuit protection, thermal

More information

Input Load (ma) Typ.

Input Load (ma) Typ. 1. Features Wide 4 : 1 Input Range Low Ripple And Noise Input / Output Isolation 1.5K Vdc Or K Vdc 100% Burn-In Input - Filter Custom Design Available Net Weight: 12 g / g Typical RoHS Converter Certified

More information

MPM V-5.5V, 4A, Power Module, Synchronous Step-Down Converter with Integrated Inductor

MPM V-5.5V, 4A, Power Module, Synchronous Step-Down Converter with Integrated Inductor The Future of Analog IC Technology MPM3840 2.8V-5.5V, 4A, Power Module, Synchronous Step-Down Converter with Integrated Inductor DESCRIPTION The MPM3840 is a DC/DC module that includes a monolithic, step-down,

More information

Output Current Input Current Load Regulation

Output Current Input Current Load Regulation PB01S/D series 1W DC/DC CONVERTER, SIP-Package FEATURES Efficiency up to 1% SIP Package with Industry Standard Pinout Package Dimension: 5V&12V Models: 19.5 x 10.2 x 6.1 mm (0.77 x 0.4 x 0.24 ) 15V&24V

More information

Bothhand USA. Features. Isolated DC-DC Converters HAA5 Series -- 5 Watt

Bothhand USA. Features. Isolated DC-DC Converters HAA5 Series -- 5 Watt Features Wide 2 : 1 Input Voltage Range(9~18V, 18~36V, 36~75V) I/O-Isolation Voltage: 4000VACrms Isolation Test Voltage 6000VDC Extended Operating Temperature Range: -40 C to +85 C Output Short Circuit

More information

ISOLATED DC-DC Converter EC4SAW SERIES APPLICATION NOTE

ISOLATED DC-DC Converter EC4SAW SERIES APPLICATION NOTE ISOLATED DC-DC Converter EC4SAW SERIES APPLICATION NOTE Approved By: Department Approved By Checked By Reported By Enoch Wade Joyce Research and Development Department Danny Jack Benny Quality Assurance

More information

CLP0112 Open Frame Power Supply Vac input; 12Vdc output; 150W Output Power

CLP0112 Open Frame Power Supply Vac input; 12Vdc output; 150W Output Power Applications Telecommunications equipment Embedded Computing Storage Systems Industrial equipment Features Compact size 50.8 mm x 101.6 mm x 36.1 mm (2 in x 4 in x 1.4 in) with density of 13.4W/in 3 Universal

More information

SPS10-24 Series small size isolated DC/DC converters

SPS10-24 Series small size isolated DC/DC converters SPS10-24 Series small size isolated DC/DC converters Features High Efficiency Wide operating temperature range ( -40 C to +85 C ) Wide 2:1 input range Dimensions 35.60 x 8.50 x 26.0 (mm) Built in over

More information

For more information, please visit the product page. input voltage 1 range. output voltage

For more information, please visit the product page. input voltage 1 range. output voltage date 9/12/218 page 1 of 1 SERIES: V78E--SMT DESCRIPTION: NON-ISOLATED DC SWITCHING REGULATOR FEATURES 1 A of output current efficiency up to SMT package industrial operating temp -~+ C designed to meet

More information

25 40 W DC/DC Power Modules 24 V Input Series

25 40 W DC/DC Power Modules 24 V Input Series PKA 2000 I 25 40 W DC/DC Power Modules 24 V Input Series Single, dual and triple output 500 V dc isolation voltage MTBF >2 million hours @75 C case temperature Complete, no extra filters or heatsinks required

More information