Analog and Telecommunication Electronics

Size: px
Start display at page:

Download "Analog and Telecommunication Electronics"

Transcription

1 Politecnico di Torino - ICT School Analog and Telecommunication Electronics F2 Active power devices»mos»bjt» IGBT, TRIAC» Safe Operating Area» Thermal analysis 30/05/ ATLCE - F DDC

2 Lesson F2: active power devices Device structure, models, parameters MOS BJT Other devices: IGBT, SCR, TRIAC Operating limits Safe Operating Area Power dissipation Thermal analysis Reference: Book 1: ch 3, ch 4, ch 5, ch 14 30/05/ ATLCE - F DDC

3 Power BJT devices Fundamental relation: Ic= β Ib Most relevant parameters for power applications: Vcebr C-E breakdown voltage Icmax max collector current β current gain (lower with high currents) Vcesat C-E voltage drop in saturation I c Thermal parameters» Max power, Thermal resistance Use vertical technology More current in the same area (higher density) I b V be V ce 30/05/ ATLCE - F DDC

4 Vertical power BJT structure Low doping in base region Wide depletion layer, high brk voltage Low current gain (5 20) High transit time Ft < 10 MHz B E n p 10^16 n 10^14 Primary breakdown Avalanche in the BC junction Secondary breakdown High current in small area (same problem as diodes)» Multiple small devices with current sharing Critical region is near saturation: High current, voltage drop high power dissipation Need to get deep saturation (problem: low β) n+ 10^19 C 30/05/ ATLCE - F DDC

5 BJT model Ebers-Moll model for BJT Simplified models (active region) BE diode + Ic source Ic = β Ib Linear models» Hybrid»Gm» 30/05/ ATLCE - F DDC

6 Switch or amplifier? Use as amplifier Active region Use as switch ON Saturation Use as switch OFF Cutoff 30/05/ ATLCE - F DDC

7 BJT as a switch Operating points are on the load line 30/05/ ATLCE - F DDC

8 BJT operation The current gain β decreases for high currents Need significant driving power Operation is based on minority carriers Slow dynamic behavior Temperature dependence To increase BVceo, base region long and lightly doped Higher epsilon Reduced E field Higher recombination probability Lower current gain High voltage devices have low current gain 30/05/ ATLCE - F DDC

9 Saturation model for BJT V source Vcesat (0.1 V) Series resistor Rcesat (few ohms) Lower Vcesat with C-E inversion (lower β) 30/05/ ATLCE - F DDC

10 Critical saturation parameters Low current gain (5 20) Critical region: Near saturation, high Ic, residual Vce High power dissipation Design solution Guarantee deep saturation (high Ib drive) Use Darlington connections» Higher current gain (and Vbe)» Single integrated structure» Npn-npn» Npn-pnp 30/05/ ATLCE - F DDC

11 Cutoff model for BJT Ib = 0 Ic = 0 (ideal) BC junction leakage current: Icbo If base open, enters as Ib, causing Iceo = β Icbo Iceo causes power dissipation Temperature rise higher leakage current further temperature rise Thermal runaway Avoid high current density areas (hot spot) Multiple devices, with current partition Steer Icbo away from Base R to GND Reverse bias BE (without breakdown!) 30/05/ ATLCE - F DDC

12 Power MOS-FET Planar structure Low power devices Current and breakdown voltage ratings function of the channel W & L. Vertical structure Voltage rating function of doping and thickness of N-epitaxial layer (vertical) Current rating is a function of the channel W & L A vertical structure can sustain both high V & I 30/05/ ATLCE - F DDC

13 MOS-FET parasitics The vertical structure creates a pn junction from body (S) to substrate (D) S G D Current can always flow from S to D A 1-quadrant switch 4-quadrant requires at least two MOS 30/05/ ATLCE - F DDC

14 MOS-FET parasitics The vertical structure creates also a parasitic transistor 30/05/ ATLCE - F DDC

15 MOS-FET parameters Basic parameters: Vdsbr D-S Breakdown voltage Idmax Max Drain current Vgsth Threshold voltage Rdson ON equivalent resistance Qg total charge injected into the Gate (for a given Vgs) A power transistor may consist of several cells (thousands) Power MOS DMOS,. (double-diffused metal oxide semiconductor) Power MOSFETs are made using this technology 30/05/ ATLCE - F DDC

16 MOS-FET model Model depends on operating point Low Vgs (subthreshold):» Exponential Medium Vgs:» Square law High Vgs:» linear Figure Typical i D v GS characteristic for a power MOSFET. 30/05/ ATLCE - F DDC

17 MOS-FET output characteristic Warning! Saturation in MOS has a different meaning (called active region in BJT) 30/05/ ATLCE - F DDC

18 MOS-FET switching models ON: Equivalent resistance Ron OFF: Leakage current Ioff Dynamic GS capacitance DS capacitance Parasitic towards substrate 30/05/ ATLCE - F DDC

19 MOS-FET gate charge Before threshold: Cgs Active region Miller effect on Cgd Saturation Cgd 30/05/ ATLCE - F DDC

20 MOS-FET vs BJT MOS-FET use majority carriers High switching speed Reduced temperature dependence MOSFET use simpler driving circuit The Gate represents a plate of a capacitor (towards GND); no current after first charging step, but Fast switching circuits able to drive a high-capacitance load ON state BJT modeled as Vcesat (+Ron) MOS modeled as Ron OFF state: both modeled as current source (leakage) 30/05/ ATLCE - F DDC

21 Four-layer devices Transistors have limitations in switching high currents at high voltages Other devices are specifically designed for such applications: four-layer devices Specific physical structure Can be used only as switches (not for linear amplifiers) A great deal in common with bipolar transistors SCR/Tyristor TRIAC/DIAC 30/05/ ATLCE - F DDC

22 4-layer device operation Circuit with two interconnected BJTs Turning on T2 provides Ic2 as Ib1 to T1, and Ic1 as Ib2. Both devices conducts until the current goes to zero. The two BJTs can be built as a single 4-layer device Tyristor or Silicon Controlled Rectifier (SCR) 30/05/ ATLCE - F DDC

23 SCR in CMOS logic circuits SCR structure intrinsic in CMOS ICs Responsible for latch up Triggered by Input levels out of GND-Vcc range High energy particles pmosfet nmosfet V G DD S D D G S V SS p+ p+ n+ n+ n+ p+ T1 p-well T2 n-substrate 30/05/ ATLCE - F DDC

24 The thyristor Four-layer device with a pnpn structure Three terminals: anode, cathode and gate Gate is the control input. Power flow between Anode and Cathode 30/05/ ATLCE - F DDC

25 Thyristor in AC power control Triggered ON by a pulse on the Gate Stays ON as long as V > 0 (remainder of the half cycle) Returns OFF when V = 0 Varying firing time changes output power Single-wave allows control from 0 50% of full power 30/05/ ATLCE - F DDC

26 The Triac and the Diac A bidirectional thyristor Allows full-wave control using a single device Often used with a diac: bidirectional trigger diode to produce the gate drive pulses The DIAC breaks down at a particular voltage and fires the triac 30/05/ ATLCE - F DDC

27 A simple lamp-dimmer using a triac Current pulse to fire the Triac Phase shift network. Provides trigger voltage for Diac 30/05/ ATLCE - F DDC

28 IGBT The Insulated Gate Bipolar Transistor or IGBT combines bipolar and MOS devices MOSFET gate-drive + high Ic and low Vcesat of BJT isolated gate FET for the control input, bipolar power transistor as a switch, in a single device combines high efficiency and fast switching. Used in medium- to high-power applications switching power supply, motor control, induction heating, Large IGBT modules (many devices in parallel), can handle» high current k 100 A» High voltages k 1000 V. 30/05/ ATLCE - F DDC

29 IGBT structure 30/05/ ATLCE - F DDC

30 IGBT characteristic 30/05/ ATLCE - F DDC

31 Lesson F2: active power devices Device structure, models, parameters MOS BJT Operating regions Other devices: IGBT, SCR, TRIAC Operating limits Safe Operating Area Power dissipation Thermal model 30/05/ ATLCE - F DDC

32 Operating limits Breakdown voltage If higher, insulating layers are broken Max current If higher, wires or conducting paths can melt Max power Power dissipation causes temperature rise (see max temp.) Max temperature Doping distribution is modified changes in parameters Silicon itself can melt Special application parameters Radiation in space,. 30/05/ ATLCE - F DDC

33 Safe Operating Area Any electronic devices can handle limited power, voltage, current For active devices, the region of acceptable V,I is the Safe Operating Area (SOA), defined by Power limit (V x I > Pdmax)» Excess power cause temperature rise, with melting» Secondary breakdown: local heating and thermal runaway Voltage (V < Vbrk)» Excess voltage causes breakdown and insulator perforation Current (I < Imax)» Excess current cause heating and metal evaporation 30/05/ ATLCE - F DDC

34 Safe Operating Area boundaries (BJT) Too high current Too high V x I (power) - not uniform current flow - high local power dissipation Active & Safe Operating Area (SOA) Too high voltage 30/05/ ATLCE - F DDC

35 SOA for BJT (TIP31) Includes dynamic behavior Pdmax depends on pulse Duty Cycle Log scale! I x V = K is a straigth line 30/05/ ATLCE - F DDC

36 SOA for MOS (IRF640) Dynamic behavior Log scale No secondary breakdown Id limited by Rds 30/05/ ATLCE - F DDC

37 Power dissipation All electric devices dissipate a power Pd = V I Power dissipation increases temperature Any device has temperature limits, therefore power limits The effects of power dissipation can be modeled using thermal equivalent circuits Power current Temperature node voltage Heat conduction capability thermal resistance θr ( /W) Diodes/MOS/BJT power dissipated on the junctions Heat must be brought outside, through a path including» Junction-case defined by manufacturer» Case-ambient controlled using heat sinks 30/05/ ATLCE - F DDC

38 Power derating Manufacturers specify Max power dissipation Pdmax Max junction operating temperature Tjmax Power dissipation causes temperature rise Allowed power dissipation decreases with Ta Ta = Tjmax Pd = 0 30/05/ ATLCE - F DDC

39 Evaluation of temperature rise Electric network model for thermal behaviour Power Pd current source Temperature T node voltage Heat conduction θ thermal resistance θr ( /W) Electrical equivalent circuit Tj Ta = Pd θja 30/05/ ATLCE - F DDC

40 From junction to ambient The thermal path from junctin to ambient consists of: Junction-Case: θ JC» Thermal resistance defined by the package Case-heatsink: θ CS» Case and fixture Heatsink-ambient: θ SA» Heatsink and operating condition (air flow) Designer can control θ CS and θ SA 30/05/ ATLCE - F DDC

41 Thermal specification Power devices specified for No heatsink, Ta specified, Tc? infinite heatsink, Tc = Ta Example datasheet TIP30 30/05/ ATLCE - F DDC

42 Power BJT datasheet (TIP31) 30/05/ ATLCE - F DDC

43 Power MOS datasheet IRF640 30/05/ ATLCE - F DDC

44 Heatsink datasheet example 30/05/ ATLCE - F DDC

45 Dynamic thermal response 30/05/ ATLCE - F DDC

46 Lesson F2: summary Describe the structure of BJT power transistors. Describe the structure of MOS power transistors. Plot output V(I) characteristic of a MOS or BJT power device, and identify the different operating regions. What is secondary breakdown? Draw a model for power BJT. Describe differences between low and high power MOS-FETs. Which parameters defines the boundary of SOA? How can we evaluate the actual temperature of a power semiconductor junction? Define the infinite heatsink concept. 30/05/ ATLCE - F DDC

Analog and Telecommunication Electronics

Analog and Telecommunication Electronics Politecnico di Torino - ICT School Analog and Telecommunication Electronics F1 - Power devices» Schottky and pin diodes» MOS, BJT, IGBT, TRIAC» Safe Operating Area» Thermal analysis 06/06/2011-1 ATLCE

More information

Analog and Telecommunication Electronics

Analog and Telecommunication Electronics Politecnico di Torino - ICT School Analog and Telecommunication Electronics F3 - Actuator driving» Driving BJT switches» Driving MOS-FET» SOA and protection» Smart switches 29/06/2011-1 ATLCE - F3-2011

More information

Power Semiconductor Devices

Power Semiconductor Devices TRADEMARK OF INNOVATION Power Semiconductor Devices Introduction This technical article is dedicated to the review of the following power electronics devices which act as solid-state switches in the circuits.

More information

Lecture Note on Switches Marc T. Thompson, 2003 Revised Use with gratefulness for ECE 3503 B term 2018 WPI Tan Zhang

Lecture Note on Switches Marc T. Thompson, 2003 Revised Use with gratefulness for ECE 3503 B term 2018 WPI Tan Zhang Lecture Note on Switches Marc T. Thompson, 2003 Revised 2007 Use with gratefulness for ECE 3503 B term 2018 WPI Tan Zhang Lecture note on switches_tan_thompsonpage 1 of 21 1. DEVICES OVERVIEW... 4 1.1.

More information

SRM INSTITUTE OF SCIENCE AND TECHNOLOGY (DEEMED UNIVERSITY)

SRM INSTITUTE OF SCIENCE AND TECHNOLOGY (DEEMED UNIVERSITY) SRM INSTITUTE OF SCIENCE AND TECHNOLOGY (DEEMED UNIVERSITY) QUESTION BANK I YEAR B.Tech (II Semester) ELECTRONIC DEVICES (COMMON FOR EC102, EE104, IC108, BM106) UNIT-I PART-A 1. What are intrinsic and

More information

Solid State Devices- Part- II. Module- IV

Solid State Devices- Part- II. Module- IV Solid State Devices- Part- II Module- IV MOS Capacitor Two terminal MOS device MOS = Metal- Oxide- Semiconductor MOS capacitor - the heart of the MOSFET The MOS capacitor is used to induce charge at the

More information

Power Electronics. P. T. Krein

Power Electronics. P. T. Krein Power Electronics Day 10 Power Semiconductor Devices P. T. Krein Department of Electrical and Computer Engineering University of Illinois at Urbana-Champaign 2011 Philip T. Krein. All rights reserved.

More information

CONTENTS. 2.2 Schrodinger's Wave Equation 31. PART I Semiconductor Material Properties. 2.3 Applications of Schrodinger's Wave Equation 34

CONTENTS. 2.2 Schrodinger's Wave Equation 31. PART I Semiconductor Material Properties. 2.3 Applications of Schrodinger's Wave Equation 34 CONTENTS Preface x Prologue Semiconductors and the Integrated Circuit xvii PART I Semiconductor Material Properties CHAPTER 1 The Crystal Structure of Solids 1 1.0 Preview 1 1.1 Semiconductor Materials

More information

UNIT 3: FIELD EFFECT TRANSISTORS

UNIT 3: FIELD EFFECT TRANSISTORS FIELD EFFECT TRANSISTOR: UNIT 3: FIELD EFFECT TRANSISTORS The field effect transistor is a semiconductor device, which depends for its operation on the control of current by an electric field. There are

More information

UNIT-1 Bipolar Junction Transistors. Text Book:, Microelectronic Circuits 6 ed., by Sedra and Smith, Oxford Press

UNIT-1 Bipolar Junction Transistors. Text Book:, Microelectronic Circuits 6 ed., by Sedra and Smith, Oxford Press UNIT-1 Bipolar Junction Transistors Text Book:, Microelectronic Circuits 6 ed., by Sedra and Smith, Oxford Press Figure 6.1 A simplified structure of the npn transistor. Microelectronic Circuits, Sixth

More information

2 Marks - Question Bank. Unit 1- INTRODUCTION

2 Marks - Question Bank. Unit 1- INTRODUCTION Two marks 1. What is power electronics? EE6503 POWER ELECTRONICS 2 Marks - Question Bank Unit 1- INTRODUCTION Power electronics is a subject that concerns the applications electronics principles into situations

More information

Fundamentals of Power Semiconductor Devices

Fundamentals of Power Semiconductor Devices В. Jayant Baliga Fundamentals of Power Semiconductor Devices 4y Spri ringer Contents Preface vii Chapter 1 Introduction 1 1.1 Ideal and Typical Power Switching Waveforms 3 1.2 Ideal and Typical Power Device

More information

I E I C since I B is very small

I E I C since I B is very small Figure 2: Symbols and nomenclature of a (a) npn and (b) pnp transistor. The BJT consists of three regions, emitter, base, and collector. The emitter and collector are usually of one type of doping, while

More information

Questions on JFET: 1) Which of the following component is a unipolar device?

Questions on JFET: 1) Which of the following component is a unipolar device? Questions on JFET: 1) Which of the following component is a unipolar device? a) BJT b) FET c) DJT d) EFT 2) Current Conduction in FET takes place due e) Majority charge carriers only f) Minority charge

More information

Analog Electronics. Electronic Devices, 9th edition Thomas L. Floyd Pearson Education. Upper Saddle River, NJ, All rights reserved.

Analog Electronics. Electronic Devices, 9th edition Thomas L. Floyd Pearson Education. Upper Saddle River, NJ, All rights reserved. Analog Electronics BJT Structure The BJT has three regions called the emitter, base, and collector. Between the regions are junctions as indicated. The base is a thin lightly doped region compared to the

More information

55:041 Electronic Circuits

55:041 Electronic Circuits 55:041 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo

More information

ECE:3410 Electronic Circuits

ECE:3410 Electronic Circuits ECE:3410 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo

More information

Semiconductor Devices

Semiconductor Devices Semiconductor Devices Modelling and Technology Source Electrons Gate Holes Drain Insulator Nandita DasGupta Amitava DasGupta SEMICONDUCTOR DEVICES Modelling and Technology NANDITA DASGUPTA Professor Department

More information

UNIT I POWER SEMI-CONDUCTOR DEVICES

UNIT I POWER SEMI-CONDUCTOR DEVICES UNIT I POWER SEMI-CONDUCTOR DEVICES SUBJECT CODE SUBJECT NAME STAFF NAME : EE6503 : Power Electronics : Ms.M.Uma Maheswari 1 SEMICONDUCTOR DEVICES POWER DIODE POWER TRANSISTORS POWER BJT POWER MOSFET IGBT

More information

COLLECTOR DRAIN BASE GATE EMITTER. Applying a voltage to the Gate connection allows current to flow between the Drain and Source connections.

COLLECTOR DRAIN BASE GATE EMITTER. Applying a voltage to the Gate connection allows current to flow between the Drain and Source connections. MOSFETS Although the base current in a transistor is usually small (< 0.1 ma), some input devices (e.g. a crystal microphone) may be limited in their output. In order to overcome this, a Field Effect Transistor

More information

Field Effect Transistors (npn)

Field Effect Transistors (npn) Field Effect Transistors (npn) gate drain source FET 3 terminal device channel e - current from source to drain controlled by the electric field generated by the gate base collector emitter BJT 3 terminal

More information

QUESTION BANK EC6201 ELECTRONIC DEVICES UNIT I SEMICONDUCTOR DIODE PART A. It has two types. 1. Intrinsic semiconductor 2. Extrinsic semiconductor.

QUESTION BANK EC6201 ELECTRONIC DEVICES UNIT I SEMICONDUCTOR DIODE PART A. It has two types. 1. Intrinsic semiconductor 2. Extrinsic semiconductor. FATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY Senkottai Village, Madurai Sivagangai Main Road, Madurai - 625 020. [An ISO 9001:2008 Certified Institution] QUESTION BANK EC6201 ELECTRONIC DEVICES SEMESTER:

More information

MTLE-6120: Advanced Electronic Properties of Materials. Semiconductor transistors for logic and memory. Reading: Kasap

MTLE-6120: Advanced Electronic Properties of Materials. Semiconductor transistors for logic and memory. Reading: Kasap MTLE-6120: Advanced Electronic Properties of Materials 1 Semiconductor transistors for logic and memory Reading: Kasap 6.6-6.8 Vacuum tube diodes 2 Thermionic emission from cathode Electrons collected

More information

EE 330 Lecture 27. Bipolar Processes. Special Bipolar Processes. Comparison of MOS and Bipolar Proces JFET. Thyristors SCR TRIAC

EE 330 Lecture 27. Bipolar Processes. Special Bipolar Processes. Comparison of MOS and Bipolar Proces JFET. Thyristors SCR TRIAC EE 330 Lecture 27 Bipolar Processes Comparison of MOS and Bipolar Proces JFET Special Bipolar Processes Thyristors SCR TRIAC Review from a Previous Lecture B C E E C vertical npn B A-A Section B C E C

More information

Student Lecture by: Giangiacomo Groppi Joel Cassell Pierre Berthelot September 28 th 2004

Student Lecture by: Giangiacomo Groppi Joel Cassell Pierre Berthelot September 28 th 2004 Student Lecture by: Giangiacomo Groppi Joel Cassell Pierre Berthelot September 28 th 2004 Lecture outline Historical introduction Semiconductor devices overview Bipolar Junction Transistor (BJT) Field

More information

Power Electronics Power semiconductor devices. Dr. Firas Obeidat

Power Electronics Power semiconductor devices. Dr. Firas Obeidat Power Electronics Power semiconductor devices Dr. Firas Obeidat 1 Table of contents 1 Introduction 2 Classifications of Power Switches 3 Power Diodes 4 Thyristors (SCRs) 5 The Triac 6 The Gate Turn-Off

More information

AN1491 APPLICATION NOTE

AN1491 APPLICATION NOTE AN1491 APPLICATION NOTE IGBT BASICS M. Aleo (mario.aleo@st.com) 1. INTRODUCTION. IGBTs (Insulated Gate Bipolar Transistors) combine the simplicity of drive and the excellent fast switching capability of

More information

EE 330 Laboratory 9. Semiconductor Parameter Measurement and Thyristor Applications

EE 330 Laboratory 9. Semiconductor Parameter Measurement and Thyristor Applications EE 330 Laboratory 9 Semiconductor Parameter Measurement and Thyristor Applications Spring 2011 Objective: The objective of this laboratory experiment is to become familiar with using a semiconductor parameter

More information

Experiment (1) Principles of Switching

Experiment (1) Principles of Switching Experiment (1) Principles of Switching Introduction When you use microcontrollers, sometimes you need to control devices that requires more electrical current than a microcontroller can supply; for this,

More information

Reg. No. : Question Paper Code : B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER Second Semester

Reg. No. : Question Paper Code : B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER Second Semester WK 5 Reg. No. : Question Paper Code : 27184 B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2015. Time : Three hours Second Semester Electronics and Communication Engineering EC 6201 ELECTRONIC DEVICES

More information

Device Technologies. Yau - 1

Device Technologies. Yau - 1 Device Technologies Yau - 1 Objectives After studying the material in this chapter, you will be able to: 1. Identify differences between analog and digital devices and passive and active components. Explain

More information

Other Electronic Devices

Other Electronic Devices Other Electronic Devices 1 Contents Field-Effect Transistors(FETs) - JFETs - MOSFETs Insulate Gate Bipolar Transistors(IGBTs) H-bridge driver and PWM Silicon-Controlled Rectifiers(SCRs) TRIACs Device Selection

More information

Field-Effect Transistor (FET) is one of the two major transistors; FET derives its name from its working mechanism;

Field-Effect Transistor (FET) is one of the two major transistors; FET derives its name from its working mechanism; Chapter 3 Field-Effect Transistors (FETs) 3.1 Introduction Field-Effect Transistor (FET) is one of the two major transistors; FET derives its name from its working mechanism; The concept has been known

More information

Unit III FET and its Applications. 2 Marks Questions and Answers

Unit III FET and its Applications. 2 Marks Questions and Answers Unit III FET and its Applications 2 Marks Questions and Answers 1. Why do you call FET as field effect transistor? The name field effect is derived from the fact that the current is controlled by an electric

More information

DOWNLOAD PDF POWER ELECTRONICS DEVICES DRIVERS AND APPLICATIONS

DOWNLOAD PDF POWER ELECTRONICS DEVICES DRIVERS AND APPLICATIONS Chapter 1 : Power Electronics Devices, Drivers, Applications, and Passive theinnatdunvilla.com - Google D Download Power Electronics: Devices, Drivers and Applications By B.W. Williams - Provides a wide

More information

ECE520 VLSI Design. Lecture 2: Basic MOS Physics. Payman Zarkesh-Ha

ECE520 VLSI Design. Lecture 2: Basic MOS Physics. Payman Zarkesh-Ha ECE520 VLSI Design Lecture 2: Basic MOS Physics Payman Zarkesh-Ha Office: ECE Bldg. 230B Office hours: Wednesday 2:00-3:00PM or by appointment E-mail: pzarkesh@unm.edu Slide: 1 Review of Last Lecture Semiconductor

More information

Power semiconductors. José M. Cámara V 1.0

Power semiconductors. José M. Cámara V 1.0 Power semiconductors José M. Cámara V 1.0 Introduction Here we are going to study semiconductor devices used in power electronics. They work under medium and high currents and voltages. Some of them only

More information

Lesson 5. Electronics: Semiconductors Doping p-n Junction Diode Half Wave and Full Wave Rectification Introduction to Transistors-

Lesson 5. Electronics: Semiconductors Doping p-n Junction Diode Half Wave and Full Wave Rectification Introduction to Transistors- Lesson 5 Electronics: Semiconductors Doping p-n Junction Diode Half Wave and Full Wave Rectification Introduction to Transistors- Types and Connections Semiconductors Semiconductors If there are many free

More information

Power Devices and ICs Chapter 15

Power Devices and ICs Chapter 15 Power Devices and ICs Chapter 15 Syed Asad Alam DA, ISY 4/28/2015 1 Overview 4/28/2015 2 Overview Types of Power Devices PNPN Thyristor TRIAC (Triode Alternating Current) GTO (Gate Turn-Off Thyristor)

More information

Lecture 3: Transistors

Lecture 3: Transistors Lecture 3: Transistors Now that we know about diodes, let s put two of them together, as follows: collector base emitter n p n moderately doped lightly doped, and very thin heavily doped At first glance,

More information

FIELD EFFECT TRANSISTOR (FET) 1. JUNCTION FIELD EFFECT TRANSISTOR (JFET)

FIELD EFFECT TRANSISTOR (FET) 1. JUNCTION FIELD EFFECT TRANSISTOR (JFET) FIELD EFFECT TRANSISTOR (FET) The field-effect transistor (FET) is a three-terminal device used for a variety of applications that match, to a large extent, those of the BJT transistor. Although there

More information

EEE118: Electronic Devices and Circuits

EEE118: Electronic Devices and Circuits EEE118: Electronic Devices and Circuits Lecture XI James E Green Department of Electronic Engineering University of Sheffield j.e.green@sheffield.ac.uk Review Review Introduced the idea of a dynamic resistance

More information

Laboratory #5 BJT Basics and MOSFET Basics

Laboratory #5 BJT Basics and MOSFET Basics Laboratory #5 BJT Basics and MOSFET Basics I. Objectives 1. Understand the physical structure of BJTs and MOSFETs. 2. Learn to measure I-V characteristics of BJTs and MOSFETs. II. Components and Instruments

More information

VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur

VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203. DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING SUBJECT QUESTION BANK : EC6201 ELECTRONIC DEVICES SEM / YEAR: II / I year B.E.ECE

More information

INTRODUCTION: Basic operating principle of a MOSFET:

INTRODUCTION: Basic operating principle of a MOSFET: INTRODUCTION: Along with the Junction Field Effect Transistor (JFET), there is another type of Field Effect Transistor available whose Gate input is electrically insulated from the main current carrying

More information

EEL 5245 POWER ELECTRONICS I Lecture #4: Chapter 2 Switching Concepts and Semiconductor Overview

EEL 5245 POWER ELECTRONICS I Lecture #4: Chapter 2 Switching Concepts and Semiconductor Overview EEL 5245 POWER ELECTRONICS I Lecture #4: Chapter 2 Switching Concepts and Semiconductor Overview Objectives of Lecture Switch realizations Objective is to focus on terminal characteristics Blocking capability

More information

NAME: Last First Signature

NAME: Last First Signature UNIVERSITY OF CALIFORNIA, BERKELEY College of Engineering Department of Electrical Engineering and Computer Sciences EE 130: IC Devices Spring 2003 FINAL EXAMINATION NAME: Last First Signature STUDENT

More information

10. Output Stages and Power Supplies. 10. Output Stages and Power Supplies TLT-8016 Basic Analog Circuits 2005/2006 1

10. Output Stages and Power Supplies. 10. Output Stages and Power Supplies TLT-8016 Basic Analog Circuits 2005/2006 1 10. Output Stages and Power Supplies 10. Output Stages and Power Supplies TLT-8016 Basic Analog Circuits 2005/2006 1 10.1 Thermal Considerations Considerable power is dissipated as heat in power devices.

More information

Digital Electronics. By: FARHAD FARADJI, Ph.D. Assistant Professor, Electrical and Computer Engineering, K. N. Toosi University of Technology

Digital Electronics. By: FARHAD FARADJI, Ph.D. Assistant Professor, Electrical and Computer Engineering, K. N. Toosi University of Technology K. N. Toosi University of Technology Chapter 7. Field-Effect Transistors By: FARHAD FARADJI, Ph.D. Assistant Professor, Electrical and Computer Engineering, K. N. Toosi University of Technology http://wp.kntu.ac.ir/faradji/digitalelectronics.htm

More information

Bipolar Junction Transistor (BJT) Basics- GATE Problems

Bipolar Junction Transistor (BJT) Basics- GATE Problems Bipolar Junction Transistor (BJT) Basics- GATE Problems One Mark Questions 1. The break down voltage of a transistor with its base open is BV CEO and that with emitter open is BV CBO, then (a) BV CEO =

More information

Today s subject MOSFET and IGBT

Today s subject MOSFET and IGBT Today s subject MOSFET and IGBT 2018-05-22 MOSFET metal oxide semiconductor field effect transistor Drain Gate n-channel Source p-channel The MOSFET - Source Gate G D n + p p n + S body body n - drift

More information

Basic Electronics. Introductory Lecture Course for. Technology and Instrumentation in Particle Physics Chicago, Illinois June 9-14, 2011

Basic Electronics. Introductory Lecture Course for. Technology and Instrumentation in Particle Physics Chicago, Illinois June 9-14, 2011 Basic Electronics Introductory Lecture Course for Technology and Instrumentation in Particle Physics 2011 Chicago, Illinois June 9-14, 2011 Presented By Gary Drake Argonne National Laboratory Session 3

More information

L MOSFETS, IDENTIFICATION, CURVES. PAGE 1. I. Review of JFET (DRAW symbol for n-channel type, with grounded source)

L MOSFETS, IDENTIFICATION, CURVES. PAGE 1. I. Review of JFET (DRAW symbol for n-channel type, with grounded source) L.107.4 MOSFETS, IDENTIFICATION, CURVES. PAGE 1 I. Review of JFET (DRAW symbol for n-channel type, with grounded source) 1. "normally on" device A. current from source to drain when V G = 0 no need to

More information

IGBTs (Insulated Gate Bipolar Transistor)

IGBTs (Insulated Gate Bipolar Transistor) IGBTs (Insulated Gate Bipolar Transistor) Description This document describes the basic structures, ratings, and electrical characteristics of IGBTs. It also provides usage considerations for IGBTs. 1

More information

MOS Field-Effect Transistors (MOSFETs)

MOS Field-Effect Transistors (MOSFETs) 6 MOS Field-Effect Transistors (MOSFETs) A three-terminal device that uses the voltages of the two terminals to control the current flowing in the third terminal. The basis for amplifier design. The basis

More information

1. Introduction Device structure and operation Structure Operation...

1. Introduction Device structure and operation Structure Operation... Application Note 96 February, 2 IGBT Basics by K.S. Oh CONTENTS. Introduction... 2. Device structure and operation... 2-. Structure... 2-2. Operation... 3. Basic Characteristics... 3-. Advantages, Disadvantages

More information

Insulated Gate Bipolar Transistor (IGBT)

Insulated Gate Bipolar Transistor (IGBT) nsulated Gate Bipolar Transistor (GBT) Comparison between BJT and MOS power devices: BJT MOS pros cons pros cons low V O thermal instability thermal stability high R O at V MAX > 400 V high C current complex

More information

Next Generation Curve Tracing & Measurement Tips for Power Device. Kim Jeong Tae RF/uW Application Engineer Keysight Technologies

Next Generation Curve Tracing & Measurement Tips for Power Device. Kim Jeong Tae RF/uW Application Engineer Keysight Technologies Next Generation Curve Tracing & Measurement Tips for Power Device Kim Jeong Tae RF/uW Application Engineer Keysight Technologies Agenda Page 2 Conventional Analog Curve Tracer & Measurement Challenges

More information

55:041 Electronic Circuits

55:041 Electronic Circuits 55:041 Electronic Circuits Output Stages and Power Amplifiers Sections of Chapter 8 A. Kruger Power + Output Stages1 Power Amplifiers, Power FETS & BJTs Audio (stereo) MP3 Players Motor controllers Servo

More information

FET(Field Effect Transistor)

FET(Field Effect Transistor) Field Effect Transistor: Construction and Characteristic of JFETs. Transfer Characteristic. CS,CD,CG amplifier and analysis of CS amplifier MOSFET (Depletion and Enhancement) Type, Transfer Characteristic,

More information

Chapter 1 Power Electronic Devices

Chapter 1 Power Electronic Devices Chapter 1 Power Electronic Devices Outline 1.1 An introductory overview of power electronic devices 1.2 Uncontrolled device power diode 1.3 Half- controlled device thyristor 1.4 Typical fully- controlled

More information

FUNDAMENTALS OF MODERN VLSI DEVICES

FUNDAMENTALS OF MODERN VLSI DEVICES 19-13- FUNDAMENTALS OF MODERN VLSI DEVICES YUAN TAUR TAK H. MING CAMBRIDGE UNIVERSITY PRESS Physical Constants and Unit Conversions List of Symbols Preface page xi xiii xxi 1 INTRODUCTION I 1.1 Evolution

More information

Chapter 3 Bipolar Junction Transistors (BJT)

Chapter 3 Bipolar Junction Transistors (BJT) Chapter 3 Bipolar Junction Transistors (BJT) Transistors In analog circuits, transistors are used in amplifiers and linear regulated power supplies. In digital circuits they function as electrical switches,

More information

UNIT 3 Transistors JFET

UNIT 3 Transistors JFET UNIT 3 Transistors JFET Mosfet Definition of BJT A bipolar junction transistor is a three terminal semiconductor device consisting of two p-n junctions which is able to amplify or magnify a signal. It

More information

Semiconductor Physics and Devices

Semiconductor Physics and Devices Metal-Semiconductor and Semiconductor Heterojunctions The Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET) is one of two major types of transistors. The MOSFET is used in digital circuit, because

More information

UNIT I PN JUNCTION DEVICES

UNIT I PN JUNCTION DEVICES UNIT I PN JUNCTION DEVICES 1. Define Semiconductor. 2. Classify Semiconductors. 3. Define Hole Current. 4. Define Knee voltage of a Diode. 5. What is Peak Inverse Voltage? 6. Define Depletion Region in

More information

SGP100N09T. Symbol Parameter SGP100N09T Unit. 70* -Continuous (TA = 100 )

SGP100N09T. Symbol Parameter SGP100N09T Unit. 70* -Continuous (TA = 100 ) SUPER-SEMI SUPER-MOSFET Super Gate Metal Oxide Semiconductor Field Effect Transistor 100V Super Gate Power Transistor SG*100N09T Rev. 1.01 Jun. 2016 SGP100N09T 100V N-Channel MOSFET Description The SG-MOSFET

More information

(a) BJT-OPERATING MODES & CONFIGURATIONS

(a) BJT-OPERATING MODES & CONFIGURATIONS (a) BJT-OPERATING MODES & CONFIGURATIONS 1. The leakage current I CBO flows in (a) The emitter, base and collector leads (b) The emitter and base leads. (c) The emitter and collector leads. (d) The base

More information

LESSON PLAN. Chap.no. Testing. & Page. Outcome No. 1. Introduction - T1 C5,95. Understand the devices. a).an ability to 2. Field intensity - potential

LESSON PLAN. Chap.no. Testing. & Page. Outcome No. 1. Introduction - T1 C5,95. Understand the devices. a).an ability to 2. Field intensity - potential EE0207 ELECTRONIC DEVICES LESSON PLAN SEMICONDUCTORS Semiconductors devices: Field intensity - potential energy - mobility - conductivity - electrons holes - charge density in semiconductors - electrical

More information

Sub-Threshold Region Behavior of Long Channel MOSFET

Sub-Threshold Region Behavior of Long Channel MOSFET Sub-threshold Region - So far, we have discussed the MOSFET behavior in linear region and saturation region - Sub-threshold region is refer to region where Vt is less than Vt - Sub-threshold region reflects

More information

SYED AMMAL ENGINEERING COLLEGE

SYED AMMAL ENGINEERING COLLEGE SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, Chennai) Established in 1998 - An ISO 9001:2008 Certified Institution Dr. E.M.Abdullah

More information

Department of Electrical Engineering IIT Madras

Department of Electrical Engineering IIT Madras Department of Electrical Engineering IIT Madras Sample Questions on Semiconductor Devices EE3 applicants who are interested to pursue their research in microelectronics devices area (fabrication and/or

More information

Lecture 16. The Bipolar Junction Transistor (I) Forward Active Regime. Outline. The Bipolar Junction Transistor (BJT): structure and basic operation

Lecture 16. The Bipolar Junction Transistor (I) Forward Active Regime. Outline. The Bipolar Junction Transistor (BJT): structure and basic operation Lecture 16 The Bipolar Junction Transistor (I) Forward Active Regime Outline The Bipolar Junction Transistor (BJT): structure and basic operation I-V characteristics in forward active regime Reading Assignment:

More information

SYLLABUS OSMANIA UNIVERSITY (HYDERABAD)

SYLLABUS OSMANIA UNIVERSITY (HYDERABAD) UNIT - 1 i SYLLABUS OSMANIA UNIVERSITY (HYDERABAD) JUNCTION DIODE Different Types of PN Junction Formation Techniques, PN Junction Characteristics, Biasing, Band Diagrams and Current Flow, Diode Current

More information

MEASUREMENT AND INSTRUMENTATION STUDY NOTES UNIT-I

MEASUREMENT AND INSTRUMENTATION STUDY NOTES UNIT-I MEASUREMENT AND INSTRUMENTATION STUDY NOTES The MOSFET The MOSFET Metal Oxide FET UNIT-I As well as the Junction Field Effect Transistor (JFET), there is another type of Field Effect Transistor available

More information

4.2.2 Metal Oxide Semiconductor Field Effect Transistor (MOSFET)

4.2.2 Metal Oxide Semiconductor Field Effect Transistor (MOSFET) 4.2.2 Metal Oxide Semiconductor Field Effect Transistor (MOSFET) The Metal Oxide Semitonductor Field Effect Transistor (MOSFET) has two modes of operation, the depletion mode, and the enhancement mode.

More information

DFP50N06. N-Channel MOSFET

DFP50N06. N-Channel MOSFET N-Channel MOSFET Features R DS(on) (Max.22 )@ =1V Gate Charge (Typical 36nC) Improved dv/dt Capability High ruggedness 1% Avalanche Tested 1.Gate 2.Drain 3.Source BS = 6V R DS(ON) =.22 ohm = 5A General

More information

Lecture 19 Real Semiconductor Switches and the Evolution of Power MOSFETS A.. Real Switches: I(D) through the switch and V(D) across the switch

Lecture 19 Real Semiconductor Switches and the Evolution of Power MOSFETS A.. Real Switches: I(D) through the switch and V(D) across the switch Lecture 19 Real Semiconductor Switches and the Evolution of Power MOSFETS 1 A.. Real Switches: I(D) through the switch and V(D) across the switch 1. Two quadrant switch implementation and device choice

More information

FYSE400 ANALOG ELECTRONICS

FYSE400 ANALOG ELECTRONICS 7.9.016 YS400 ANALOG LTONS LTU 1 ntroduction to ipolar Junction Transistor ircuits 1 NTODUTON The deal urrent-controlled urrent Source efore the detailed analyzation of transistor operation, we should

More information

Chapter 8. Field Effect Transistor

Chapter 8. Field Effect Transistor Chapter 8. Field Effect Transistor Field Effect Transistor: The field effect transistor is a semiconductor device, which depends for its operation on the control of current by an electric field. There

More information

UNIT II JFET, MOSFET, SCR & UJT

UNIT II JFET, MOSFET, SCR & UJT UNIT II JFET, MOSFET, SCR & UJT JFET JFET as an Amplifier and its Output Characteristics JFET Applications MOSFET Working Principles, SCR Equivalent Circuit and V-I Characteristics. SCR as a Half wave

More information

Three Terminal Devices

Three Terminal Devices Three Terminal Devices - field effect transistor (FET) - bipolar junction transistor (BJT) - foundation on which modern electronics is built - active devices - devices described completely by considering

More information

EC6202-ELECTRONIC DEVICES AND CIRCUITS YEAR/SEM: II/III UNIT 1 TWO MARKS. 1. Define diffusion current.

EC6202-ELECTRONIC DEVICES AND CIRCUITS YEAR/SEM: II/III UNIT 1 TWO MARKS. 1. Define diffusion current. EC6202-ELECTRONIC DEVICES AND CIRCUITS YEAR/SEM: II/III UNIT 1 TWO MARKS 1. Define diffusion current. A movement of charge carriers due to the concentration gradient in a semiconductor is called process

More information

Pre-certification Electronics Questions. Answer the following with the MOST CORRECT answer.

Pre-certification Electronics Questions. Answer the following with the MOST CORRECT answer. Electronics Questions Answer the following with the MOST CORRECT answer. 1. The cathode end terminal of a semiconductor diode can be identified by: a. the negative sign marked on the case b. a circular

More information

Analog and Telecommunication Electronics

Analog and Telecommunication Electronics Politecnico di Torino - ICT School Analog and Telecommunication Electronics A3 BJT Amplifiers»Biasing» Output dynamic range» Small signal analysis» Voltage gain» Frequency response 12/03/2012-1 ATLCE -

More information

IFB270 Advanced Electronic Circuits

IFB270 Advanced Electronic Circuits IFB270 Advanced Electronic Circuits Chapter 11: Thyristors Prof. Manar Mohaisen Department of EEC Engineering Review of the Precedent Lecture To introduce several concepts on capacitance in amplifiers

More information

EE70 - Intro. Electronics

EE70 - Intro. Electronics EE70 - Intro. Electronics Course website: ~/classes/ee70/fall05 Today s class agenda (November 28, 2005) review Serial/parallel resonant circuits Diode Field Effect Transistor (FET) f 0 = Qs = Qs = 1 2π

More information

3. Draw the two transistor model of a SCR and mention its applications. (MAY 2016)

3. Draw the two transistor model of a SCR and mention its applications. (MAY 2016) DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE6503 POWER ELECTRONICS UNIT I- POWER SEMI-CONDUCTOR DEVICES PART - A 1. What is a SCR? A silicon-controlled rectifier

More information

UNIT-VI FIELD EFFECT TRANSISTOR. 1. Explain about the Field Effect Transistor and also mention types of FET s.

UNIT-VI FIELD EFFECT TRANSISTOR. 1. Explain about the Field Effect Transistor and also mention types of FET s. UNIT-I FIELD EFFECT TRANSISTOR 1. Explain about the Field Effect Transistor and also mention types of FET s. The Field Effect Transistor, or simply FET however, uses the voltage that is applied to their

More information

Q1. Explain the construction and principle of operation of N-Channel and P-Channel Junction Field Effect Transistor (JFET).

Q1. Explain the construction and principle of operation of N-Channel and P-Channel Junction Field Effect Transistor (JFET). Q. Explain the construction and principle of operation of N-Channel and P-Channel Junction Field Effect Transistor (JFET). Answer: N-Channel Junction Field Effect Transistor (JFET) Construction: Drain(D)

More information

Bipolar Junction Transistors (BJTs) Overview

Bipolar Junction Transistors (BJTs) Overview 1 Bipolar Junction Transistors (BJTs) Asst. Prof. MONTREE SIRIPRUCHYANUN, D. Eng. Dept. of Teacher Training in Electrical Engineering, Faculty of Technical Education King Mongkut s Institute of Technology

More information

Field Effect Transistors

Field Effect Transistors Field Effect Transistors LECTURE NO. - 41 Field Effect Transistors www.mycsvtunotes.in JFET MOSFET CMOS Field Effect transistors - FETs First, why are we using still another transistor? BJTs had a small

More information

1. (2pts) What is the purpose of the buried collector in a bipolar process?

1. (2pts) What is the purpose of the buried collector in a bipolar process? EE 330 Exam 2 Fall 2013 Name Instructions: This is a 50-minute exam. Students may bring 2 pages of notes (front and back) to this exam. The points allocated to each question and each problem are as indicated.

More information

1 Introduction to analog CMOS design

1 Introduction to analog CMOS design 1 Introduction to analog CMOS design This chapter begins by explaining briefly why there is still a need for analog design and introduces its main tradeoffs. The need for accurate component modeling follows.

More information

8. Characteristics of Field Effect Transistor (MOSFET)

8. Characteristics of Field Effect Transistor (MOSFET) 1 8. Characteristics of Field Effect Transistor (MOSFET) 8.1. Objectives The purpose of this experiment is to measure input and output characteristics of n-channel and p- channel field effect transistors

More information

Basic Electronics: Diodes and Transistors. October 14, 2005 ME 435

Basic Electronics: Diodes and Transistors. October 14, 2005 ME 435 Basic Electronics: Diodes and Transistors Eşref Eşkinat E October 14, 2005 ME 435 Electric lectricity ity to Electronic lectronics Electric circuits are connections of conductive wires and other devices

More information

INTRODUCTION TO MOS TECHNOLOGY

INTRODUCTION TO MOS TECHNOLOGY INTRODUCTION TO MOS TECHNOLOGY 1. The MOS transistor The most basic element in the design of a large scale integrated circuit is the transistor. For the processes we will discuss, the type of transistor

More information

VALLIAMMAI ENGINEERING COLLEGE SRM NAGAR, KATTANKULATHUR- 603 203 DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING EC6202- ELECTRONIC DEVICES AND CIRCUITS UNIT I PN JUNCTION DEVICES 1. Define Semiconductor.

More information

Power MOSFET Basics. Table of Contents. 2. Breakdown Voltage. 1. Basic Device Structure. 3. On-State Characteristics

Power MOSFET Basics. Table of Contents. 2. Breakdown Voltage. 1. Basic Device Structure. 3. On-State Characteristics Power MOSFET Basics Table of Contents P-body N + Source Gate N - Epi 1. Basic Device Structure 2. Breakdown Voltage 3. On-State Characteristics 4. Capacitance 5. Gate Charge 6. Gate Resistance 7. Turn-on

More information

Index. Small-Signal Models, 14 saturation current, 3, 5 Transistor Cutoff Frequency, 18 transconductance, 16, 22 transit time, 10

Index. Small-Signal Models, 14 saturation current, 3, 5 Transistor Cutoff Frequency, 18 transconductance, 16, 22 transit time, 10 Index A absolute value, 308 additional pole, 271 analog multiplier, 190 B BiCMOS,107 Bode plot, 266 base-emitter voltage, 16, 50 base-emitter voltages, 296 bias current, 111, 124, 133, 137, 166, 185 bipolar

More information