BUSBAR TRUNKING SYSTEMS 25A-63A AB-E SERIES. The smartest way of power distribution.

Transcription

1 BUSBAR TRUNKING SYSTEMS SERIES 25A-63A

2 TABLE OF CONTENTS SERIES General Information 2-4 Project Information 5-6 Fittings Straight Lengths 7-8 Elbow Modules 8-9 Dilatation Module 9 Top Feed Module 10 End Feed Module 10 Centre Feed Module 11 Tap-Off Plug 11 Tap-Off Unit 12 Flanged End 13 Hanger Kit Hanger Technical Data Technical Data 19 Busbar Features 19 Installation Installation 20 Kit Installation 20 Quality Certificates Quality Certificates 21 Certificates

3 General Features DTM s Series Busbar Trunking System is designed to meet all lighting requirements from 25A to 63A. Technical Data Made of galvanized sheet, the enclosure of the Busbar Trunking System is roll formed for increased mechanical strength. There are 4 PVC insulated conductors: L1, L2, L3 and N+Pe. The cross section of the neutral conductor (optionally 5 conductors) is same as that of the phase conductor. The housing is used for earthing. The Busbar Trunking System is tested and designed according to the standard IEC /6. Installation through a cable trunk is possible. Smoke, light intensity, etc. can be controlled using a PLC and a Router. The Busbar Trunking System is manufactured in compliance with the standard ISO 9000 under a certified quality assurance system. Advantages Fittings For an adaptable lighting system, fittings allow for taking optimal advantage of space and for both vertical and horizontal installation. 3-step easy and quick installation: 1. Hangers are placed for hanging the busbars. 2. For connecting two busbars, one busbar is attached to the spring retainer pin. 3. No skilled person or special tool is required for installation. Advantages of the Busbar Trunking System Easy Easy-to-design power distribution, clear network structure and easy engineering and installation Quick With minimum number of tools, quick installation and reduced installation time Flexible Easy-to-extend and modify Plug-In Points The standard distance between two tap-off points is 75 cm. Standard lengths with higher number of plug-in points are available upon request. Colored Covers The tap-off plug covers of DTM s Series Busbar Trunking System are designed in different colors so as to allow for seeing the phase supplied. Tap-Off Plugs and Tap-Off Units The tap-off plugs and tap-off units of DTM s Busbar Trunking Systems are designed with different contact sequences in order to avoid the misuse of the busbar. In order to avoid the misuse of the phase, all tap-off plugs and tap-off units are manufactured so as to allow for unidirectional connection with the busbar. Safety For safety reasons, the first and last members to contact the busbar housing are the earth conductors of the tap-off plugs and tap-off units. Conductor Option In addition to full-section phase and neutral conductors, earth conductors are available upon request. Silver Plated Contact Pins Contact resistances are minimized. 4 5

4 Order Code System TECHNICAL DETAILS Number of Active Conductors n Cu Busbar Dimensions A x B (mm) 39x x x x57.5 C 12 5 T2 PS Rated Current ln (A) Busbar Cross-Section (3P+N) S (mm 2 ) Rated Operational Voltage Ue (V) Rated Insulation Voltage Ui (V) Rated Frequency f (Hz) 50/60 50/60 50/60 50/60 Rated Short-Circuit Current lcw (ka)rms BUSBAR NAME Peak Current lpk (ka) COPPER (C) Plug-In Busbar Elbow Module PS DM Max. Thermal Limit l 2 (A 2 sx10 ) Phase Resistance R 20 (mω/m) COPPER CURRENT BUSBAR CODE 25A 12 Plug-In Optional Length Tap-Off Plug Top Feed Module End Feed Module Centre Feed Module Flanged End PX F BM SM OM S Phase Reactance X (mω/m) Phase Impedance Z (mω/m) Protective Busbar Resistance R PE (mω/m) Protective Busbar Reactance X PE (mω/m) A 13 40A 14 63A 16 IP 55 5 Hanger Kit Tap-Off Plug with Automatic Fuse Joint Cover U Hanger C Hanger L Hanger Wall Hanger A SF E UA CA LA DA Fault-Loop Resistance R 0 (mω/m) Fault-Loop Reactance X 0 (mω/m) Fault-Loop Impedance Z 0 (mω/m) Distributed Load Voltage Drop ΔV3F = 3/2 (Rcosø + 2x sinø) Linear Busbar Weight p (kg/m) Ceiling Hanger TA Fire Load (kwh/m) NUMBER OF CONDUCTORS CODE L1 L2 L3 N 1/2 EARTH CLEAN EARTH 1/2 CLEAN EARTH 3P+N+PE (4P) T P+N+PE+FE1 (5P) T EARTH IP Joule Effect Loss in Rated Current P (W/m) Ambient Temperature min. / maks. t ( C) -5/+50-5/+50-5/+50-5/

5 Standard Length Optional Length Plug-In Busbar Standard Length PS Plug-In Busbar Optional Length PX 32 A Copper Plug-In IP55 5 Conductor C135T2PS 25 A Copper Plug-In Optional Length IP55 5 Conductor C125T2PXT Optional lengths are manufactured as 1 mt, 1.5 mt and 2 mt. OPTIONAL LENGTH ORDER CODES LENGTH MM CODE 1000 W 1500 T 2000 L 8 9

6 Elbow Modules Feeder Modules Elbow Modules DM End Feed Module SM 32 A Copper Horizontal Elbow IP55 5 Conductor C135T2DM 40 A Copper Feeder Module IP55 5 Conductor C145T2SM Top Feed Module BM 25 A Copper Feeder Module IP55 5 Conductor C125T2BM 10 11

7 Centre Feed Tap-Off Plug Tap-Off Unit With Automatic Fuse Centre Feed Module OM Tap-Off Unit with Automatic Fuse SF 63 A Copper Centre Feed IP 55 5 Conductor C165T2OM Tap-Off Plug F 25 A Copper Tap-Off Plug IP 55 5 Conductor C255T212F AMR TAP-OFF PLUG PHASE SEQUENCE CODE L1,N,PE 1 L2,N,PE 2 L3,N,PE 3 L1,L2,L3,N,PE 4 L1,N,PE 5 L2,N,PE 6 L3,N,PE 7 L1,L2,L3,N,PE 8 L1,N,PE 9 L2,N,PE 10 L3,N,PE 11 L1,L2,L3,N,PE 12 L1,N,PE 13 L2,N,PE 14 L3,N,PE 15 L1,L2,L3,N,PE A Copper Tap-Off Unit IP 55 5 Conductor C325T232SF AMR TAP-OFF PLUG PHASE SEQUENCE KOD L1,N,PE 17 L2,N,PE 18 L3,N,PE 19 L1,L2,L3,N,PE 20 L1,N,PE 21 L2,N,PE 22 L3,N,PE 23 L1,L2,L3,N,PE 24 L1,N,PE 25 L2,N,PE 26 L3,N,PE 27 L1,L2,L3,N,PE 28 L1,N,PE 29 L2,N,PE 30 L3,N,PE 31 L1,L2,L3,N,PE

8 Flanged End Joint Covers Busbar and Fittings Hanger Flanged End S 30 mm Hanger (U) UA UA 32 A Copper Flanged End IP 55 5 Conductor 88 mm C135T2S 41 mm Joint Cover E C5T2E 14 15

9 Busbar and Fittings Hanger Busbar and Fittings Hanger 50 mm Hanger (L) LA 60 mm Hanger (C) CA 118 mm LA 98 mm CA 40 mm

10 Hangers Hangers Wall-Type Hanger DA Hangers T 25 mm 42 mm DA T 59 mm 1 2 Expansion Bolt Extension Member FITTINGS DESCRIPTION W (mm) Code B-E 8 Rod Hanger (M8) 500 T101 B-E 8 Rod Hanger (M8) 1000 T102 (M8) Extension Member - T103 M 8 Draw-In Anchor - T104 M 8 Steel Nut - T105 Ceiling-Type Hanger TA 25 mm TA 59 mm 1 2 W Tij 42 mm 18 19

11 Busbar Technical Data Installation Instructions Align the pin on the joint of the 1 2 housing with the pin hole of the other housing. Insert the pin into the pin hole. AMPERE RATING 25A 39 COPPER BUSBAR DIMENSIONS AND WEIGHTS BUSBAR mm FEEDER KG 3P+N+PE (4) 3P+N+PE+FE1 (5) A X 40A A Jointing of the housing is completed once the pin is inserted into the pin hole. CLICK 4 Place the joint cover and screw the covers together. 5 Jointing is completed once the joint covers are screwed

12 Product Group Manufacturer EC DECLARATION OF CONFORMITY Busbar Power Distribution Systems DTM Elektroteknik San. ve Tic. A.Ş Çatalmeşe Mah. Sultansuyu Cad. No: Çekmeköy / Istanbul We hereby confirm that the above-stated product/product group manufactured in DTM s Plants is in conformity with the following standards and directives. Standard TS EN Low-voltage switchgear and control gear assemblies Part 6: Busbar trunking systems (busways) EC Directive (2006/95/EC) Directive relating to electrical equipment designed for use within certain voltage limits Date DTM Elektroteknik San. Tic. A.Ş. Çatalmeşe Mah. Sultansuyu Cad. No: Çekmeköy / Istanbul Phone: +90(216) BUSBAR EQUIPMENT LIST TYPE PCS. CATALOG NO COMPANY PROJECT PROJECT NO Please use this page by photocopying 22

13