Model PHASE DIGITAL POWER CLAMP METER USERS MANUAL

Size: px
Start display at page:

Download "Model PHASE DIGITAL POWER CLAMP METER USERS MANUAL"

Transcription

1 Model 577 PHSE DIGITL POER CLMP METER USERS MNUL

2 CONTENTS Safety Precautions Safety Information Safety Symbols General Description Feature Meter Layout Using The Selector Using The Buttons Lcd Display Making Measurements Measuring c Voltage Measuring c Current Measuring Single-Phase Circuit Measuring Three -Phase Four-ire Circuit Measuring Three -Phase Three-ire Circuit Saving Measurement Recalling Memory RSC Date Interface Input Voltage nd Current Backlight Display Sketch Of Safety Holding Curve Diagram Of Power Low Voltage Indication Replacing Batteries Specifications ccessories

3 Safety Precautions Read these operation instructions thoroughly and completely before operating your meter. Pay particular attention to RNINGS. The instructions in these warnings must be followed. You must be careful when working with voltages above V. Keep fingers behind the probe barriers while measuring. Never use the meter to measure voltages that might exceed the maximum allowable input value of any function measurement mode. lways inspect your meter and test leads before every use. If any abnormal conditions exist: broken test leads, cracked cases, LCD not reading, etc, do not attempt to take any measurement. Using the meter with the equipped test leads to conform to safety requirements. If you need to replace broken test leads, you must replace with the same type and electric specification. Never touch a voltage source when the test leads are plugged into a current jack. Do not expose the instrument to direct sunlight, extreme temperature or moisture. RNING RED THE INSTRUCTIONS BEFORE USING THE INSTRUMENT Safety Information Three-phase digital power clamp meter has been designed according to IEC- and IEC-- concerning safety requirements for electrical measuring instruments and handheld clamps with pollution degree, overvoltage category ( 6V CTⅢ ). -

4 Safety Symbols Important safety information, refer to the operating manual Dangerous voltage may be present. Earth ground Double insulation (Protection classⅡ ) Battery General Description Three-phase digital power clamp meter is a handheld aptitude meter with power measurement; it incorporates current meter and power measurement instrument. The meter is composed of three channels: voltage, current, power and single chip Microcontroller. It has powerful measuring and data processing software, and complete to measure, calculate and display of the 8 parameters: Voltage, Current, ctive Power, Power Factor, pparent Power, Reactive Power, ctive Energy, and Frequency. It has Stable capability, easy operation. It is especially suitable for measurement and overhaul of the electric power equipment and the power-supply circuit on the spot. The structure of the instrument is pincers. It is very small, very light and portable, making measurements easy and fast. To the power measurement user, the digital power clamp meter which is used completely in three-phase systems is one of the best instruments. Feature. For power measurement of -phase -wire circuit, -phase 4-wire circuit, single-phase circuit.. The instrument can complete the true RMS value measurement. If there is nonsinusoidal current input signal, it can accurately measure the active current. - -

5 . Using autorange switch circuit and modulus transducer which has 8 count and high resolution, the instrument has high accuracy and easy operation. 4. Minimum current of ctive Energy measurement is.5, it can measure expending energy per hour of general electrical equipment. Measurement and display five parameters of power: ctive Power, pparent Power, Power Factor, Reactive Power, ctive Energy. 5. Double display two parameters on each menu and store 8 groups of measurement parameter. 6. Measure five power parameters of each phase and total power value in three-phase measurement mode respectively. 7. Multifunctional button control, there are double scales analogue bar graph to display fluctuation of voltage and current. 8. ith PC RSC interface and special INDOS data graphics software. 9. Display measurement time and select tested voltage signal power supply for the clamp at one time in ctive Energy measurement mode, so the instrument can measure for a long time.. The instrument is a portable clamp meter. It is very light and convenient to carry. - -

6 Meter Layout 6k 6V CT.III DIGITL POER CLMP MS HOLD 8 EX- P 7 Ture RMS UTO RNGE OPTICL INTERFE ~ RS 6V V / Hz RS CLER 6 DC CL RS PF P Hz FREQ Time hmin 4 V V V COM 5 ( Figure ). Clamp Jaws Ф 5mm. HOLD Button Holds the display reading and " symbol is shown in the LCD display, press this button again, the meter returns to normal measurement mode.. Function Selector Rotary Switch Rotate the selector to any measurement function. 4. Function Selector Buttons To select the measurement object. 4

7 5. Input terminal V: The input terminal for the first phase, using the yellow test lead to connect. V: The input terminal for the second phase, using the green test lead to connect. V: The input terminal for the third phase, using the red test lead to connect. COM: Common terminal, the earth input terminal for all measure- 6. LCD Display -ment modes, using the black test lead to connect. 4 digit display, 7 segment LCD to display function mode, measured value and symbols. 7. Trigger Press the lever to open the transformer. hen the lever is released, the jaws will close again. 8. RSC Data Interface Your clamp meter can use a serial interface cable to communicate with a computer. Refer to Figure 8 for complete instructions. Using the Selector Turn the meter on by rotating the selector to any function as following. ( Table. Introducing The Selector) ITEM EX- P DESCRIPTION POER. Turn the meter off EXTERNL POER SUPPLY. Use without battery, select tested voltage signal power supply for ctive Energy measurement for long use at one time. RECLL DT. Recall saved data in the meter memory. TOTL POER. For display total power value of three phase 5

8 ( Table. Introducing The Selector ) ITEM Φ DESCRIPTION THIRD MESUREMENT CHNNEL. For V input terminal measurement Φ SECOND MESUREMENT CHNNEL. For V input terminal measurement Φ FIRST MESUREMENT CHNNEL. For V input terminal measurement Using the buttons ( Table. Function Button) ITEM DESCRIPTION ctive Power, Power Factor Measurement Button. pparent Power, Reactive Power Measurement Button. ctive Energy, Time Measurement Button 4 Power Summation Button V / Hz RS CLER Voltage, Frequency Measurement Button Current Measurement Button Data Transmit Button Clear Memory Button 9 Backlight Button Maximum Value Button/ Previous Record Button Minimum Value Button/ Next Record Button Data Save Button 6

9 . Press ctive Power, Power Factor Measurement Button button to measure ctive Power and Power Factor in measurement mode. Then the LCD shows ctive Power reading in the primary display and Power Factor reading in the secondary display.. Press pparent power, Reactive Power measurement button button to measure pparent Power and Reactive Power in measurement mode. Then the LCD shows pparent Power reading in the primary display and Reactive Power reading in the. secondary display. ctive Energy, Time Measurement Button Press button to measure ctive Energy in measurement mode. Then the LCD shows ctive Energy reading in the primary display and measurement time of the ctive Energy in the secondary display. 4. Power Summation Button Press button to sum up the measured value of current one phase in three phase measurement mode; then measure the second phase and press the button to sum up again; press the button for the third phase after you get the measured value of the third phase on the display. Then the meter will calculate the sum in this three phase system automatically, you will rotate the selector to at one time, then the display shows the total power value. V / Hz 5. Voltage Measurement Button Press V / Hz button to measure voltage of the circuit and display the measured value in the LCD display. 7

10 6. Press Current Measurement Button button to measure current of the circuit and display the measurement value in the LCD display. 7. RS Data Transmit Button Press RS button to transmit measured data to a computer by special interface cable, you can record current measured value and print reports and data trend curve drawing. Before pressing the RS button to transmit measured data, you must connect RSC interface cable to the clamp meter and a 8. computer, the communication function is now working. CLER Clear Memory Button Press CLER button for three seconds to erase all measured data in the meter memory in the measurement mode. 9. Backlight Button Press button to turn the backlight on or off. hen the back- -light is turned on over five seconds, it will turn off automatically.. Button Maximum Value Measurement Button / Previous Record Press button to measure maximum value in measurement mode. The display shows current maximum value in the secondary display. hen you turn the selector to, press button to recall previous memory location and display the data on the LCD. Once pressing this button, the clamp meter recalls a memory location. previous current location. Minimum Value Measurement Button / Next Record Button Press button to measure minimum value in measurement mode, the display shows current minimum value in the secondary display. 8

11 hen you turn the selector to, press button to recall next memory location and display the data on the LCD. Once pressing this button, the clamp meter recalls a memory location next current location.. Data Save Button Press button to save current measured data to the meter in measured mode. The meter can save 8 groups of measured data into the meter at most. Lcd Display ( Figure ). Dangerous voltage symbol. Data holding symbol. First phase symbol 4. Second phase symbol 5. Third phase symbol 6. Three phase total power symbol 7. External power supply symbol 8. Battery symbol - 9 -

12 9. Voltage unit (V), current unit (), pparent Power unit () ( For primary display ). ctive power unit (k) ctive Energy unit (). 4 digit display ( For primary display ). Frequency unit. Voltage unit (V), current unit (), pparent Power unit (), Reactive Power unit () ( For secondary display ) 4. Time unit : hour(h) minute(min) 5. Overflow symbol 6. graduate scale 7. 4 graduate scale 8. Bar graph 9. 4 digit display ( For secondary display ). Frequency unit. Time symbol. Negative sign of scale. Number of memory location symbol 4. Recall data symbol 5. Save data symbol 6. Minimum value symbol 7. Power factor symbol 8. Maximum value symbol 9. RSC interface symbol. Calibrate symbol. Negative symbol. symbol. DC symbol - -

13 Ture RMS UTO RNGE P HOLD 4 Making Measurements Measuring Voltage FREQ V Hz 6k 6V CT.III Circuit V EX- V V V / Hz RS CLER FREQ Hz FREQ V Hz 4 V V V COM Black Yellow ( Figure. Voltage Measurements). Turn the selector to one of Φ,Φ,Φ, refer to Table to connect the test leads to input terminals: Insert the black test lead into the COM input terminal and one corresponding color test lead into the corresponding input terminal.( Figure ) (Table Input Terminal Connections) SELECTOR INPUT TERL(+) INPUT TERL(-) Phase Φ V jack Yellow lead COM jack Black lead First phase Φ V jack Green lead COM jack Black lead Second phase Φ V jack Red lead COM jack Black lead Third phase. Connect test leads to the load, press V / Hz button, voltage measured value is displayed in the primary display and current frequency value of voltage is shown in the secondary display. - -

14 6k Ture RMS UTO RNGE V / Hz FREQ P HOLD CLER 4 6V CT.III. In voltage measurement mode, press button, the LCD displays symbol, then maximum value(trms) is shown in the secondary display. Press button again, the symbol disappears, the secondary display returns to current frequency value. 4. Press button, the LCD displays symbol, then minimum value(trms) is shown in the secondary display. Press button again, the symbol is disappeared, the secondary display return to current frequency value. 5. If input voltage exceeds 6V, the display will show OL symbol and the bar graph is full.( Figure 4 ) Circuit V EX- V V RS FREQ Hz V Hz V V V COM Black Yellow ( Figure 4. Voltage Exceeds 6V ) 6. If input voltage exceeds V, the display will show for safety. 7. There are two modes to show the bar graph in the LCD. You can observe fluctuation range of measured voltage. The first mode is , the second is Measuring Current

15 Ture RMS UTO RNGE RS P HOLD 4 Test ed conduct or 6k 6V CT.III Earth wire EX- RS V / Hz RS CLER 4 V V V COM ( Figure 5. Current Measurements). Turn the selector to one of Φ,Φ,Φ.. Press the trigger to hook the clamp jaw around one conductor to be measured. Press button, the primary display reading is current value (RMS) of the conductor. ( Figure 5). To measure the maximum value of current, press button, the maximum value is shown in the secondary display. Press button again to cancel maximum value measurement. ( Figure 6) 4. To measure the minimum value of current, press button, the minimum value is shown in the secondary display. Press button again to cancel minimum value measurement. 5. For current exceeds (RMS), the display will show OL symbol. ( Figure 7) -

16 Ture RMS UTO RNGE Ture RMS UTO RNGE RS P P HOLD HOLD There are two modes to show the bar graph. You can observe the fluctuation range of measured current. The first mode is , the second is ( Figure 5 and Figure 6 ) Tested conductor 6k 6V CT.III Earth wire EX- V / Hz RS CLER V V V COM ( Figure 6. Maximum Value Of Current Measurements ) 6k 6V CT.III Tested conductor Earth wire EX- V / Hz RS CLER V V V COM ( Figure 7. Current Exceeds ) - 4 -

17 Ture RMS UTO RNGE HOLD Measuring Single-Phase Circuit Tested conductor 6k 6V CT.III Earth wire EX- P k V / Hz RS CLER k PF PF V V V COM Black Green (Figure 8. Single-phase Power Measurements). Hook the clamp jaws around the conductor of the loading or the circuit. The clamped conductor is one phase which you want to test in the three-phase circuit.. Turn the selector to one of Φ,Φ,Φ, and refer to Table to connect test leads into input terminals which is corresponding to the position of the selector. ( Figure 8). fter right connection, you can measure five power parameters of single-phase circuit (ctive Power, Power Factor, pparent Power, Reactive Power, ctive Energy): (. ) ctive Power(k) and Power Factor (PF) (Figure 8 ) a. Press button, the ctive Power value is shown in the primary display and the Power Factor value, PF symbol are shown in the secondary display. hen the Power Factor value is negative, the loading is capacitive

18 Ture RMS UTO RNGE HOLD b. The maximum measurement range of ctive Power is 6k. For exceeding the maximum value, the OL symbol will be shown in the display. If test voltage exceeds 6V or the test current exceeds, the OL symbol will be shown in the display too. nd the bar graph is full.(figure 9) The minimum input voltage is V and the minimum input current is 5, if it less than the minimum input voltage and minimum input current, the ctive Power value is.k. c. Press button, the maximum value of ctive Power is shown in the secondary display. d. Press button, the minimum value of ctive Power is shown in the secondary display. e. The bar graph is shown. Tested conductor 6k 6V CT.III Earth wire EX- P k V / Hz RS CLER k PF PF V V V COM Black Green (Figure 9.Current Exceeds Or Voltage Exceeds 6V) - 6 -

19 6k Ture RMS UTO RNGE V / Hz P 4 6 HOLD CLER 8 6V CT.III (. ) pparent Power ()and Reactive Power ( ) a. Press button, the pparent Power value is shown in the primary display, Reactive Power value and the bar graph are shown in the secondary display.(figure ) Tested conductor Earth wire EX- RS V V V COM Black Red (Figure.pparent power measurements) b. For input voltage less than V and input current less than 5, pparent Power value is.. c. Press button, the maximum value of pparent Power is shown in the secondary display. d. Press button, the minimum value of pparent Power is shown in the secondary display. e. Reactive Power is not direct measuring parameter of power, = -k is a formula to calculate Reactive Power value. The value is calculated and shown according to measured voltage, current and ctive Power in software

20 6k Ture RMS UTO RNGE V / Hz HOLD CLER 6V CT.III (.) ctive Energy () and Time(hmin) a. In ctive Energy measurement mode, voltage signal must be input into V and COM terminal of the clamp meter (Figure ), and the selector must be turned to Φ.So the ctive Energy measurement function is valid, Tested conductor Earth wire EX- P RS hmin hmin V V V COM Black Yellow b. Press ( Figure. ctive Energy measurements) button, starting value of the ctive Energy is. and is shown in the primary display at first, ctive Energy measured time and the bar graph is shown in the secondary display. fter time time passe, the measured value of ctive Energy will be larger. If you need to read the ctive Energy value, press the HOLD button, so the measured value display and the display of the measured time are locked, but the ctive Energy measurement continues along with timing in the clamp meter. fter reading the display, press the HOLD button again to exit date hold - 8 -

21 and continue to measure, ctive Energy value still adds up. ctive energy measurement doesn t stop until another measurement function is selected. c. The button and button is invalid in ctive Energy measurement mode. d. The maximum value of ctive Energy is If ctive Energy value exceeds the maximum value, the display will show OL symbol. e. ctive energy measurement is viable in a single-phase circuit because you only measure current of one phase at one time, so you cannot measure three-phase ctive Energy. If you need to measure ctive Energy for a long time during measurement, you should use the EX- P function, so the meter will work without using the battery but will use test voltage signal as power supply. NOTE: hen you turn the selector to EX- P to measure voltage or power parameter, the input voltage of V jack must less than 5V, otherwise the fuse will blow. Measuring Three Phase Four-ire Circuit Three-phase power parameter means total ctive Power, total Reactive Power, total pparent Power, total Power Factor. The clamp meter cannot measure three-phase ctive Energy. The measurement method of three-phase power parameter is that you measure power parameter of each phase conductor respectively at first, then calculate three-phase power parameter in the meter. For a balance load, the measured data is accurate, if power parameter fluctuates larger, then the error of total power parameter increases more

22 6k Ture RMS UTO RNGE V / Hz PF P HOLD CLER 6V CT.III. Refer to Table, connect yellow test lead, green test lead, red test lead to every phase live wire of the three-phase circuit and V jack, V jack, V jack of the meter respectively, connect black test lead to zero conductor of the circuit and COM jack of the meter.. Turn the selector to Φ at first ( to first phase measurement ), hook the clamp jaw around the first phase conductor of the tested circuit, press button to measure ctive Power (k) and Power Factor (PF). The measured value is shown in the LCD then press button to sum power parameter of this phase; press button again to measure pparent Power and Reactive Power, after the result is shown in the LCD, press button to sum power parameter of this phase. The power parameter measurement is completed in the first phase. If you need save the result, you can press button to do it. ( Figure ) Tested conductor PF k EX- Earth wire RS k V V V COM Black Red Green Yellow ( Figure.The First Phase Power Measurements ) - -

23 6k Ture RMS UTO RNGE V / Hz PF P HOLD CLER 6V CT.III. Turn the selector to Φ (to the second phase measurement), hook the clamp jaw around the second phase conductor of the tested circuit, press button and button to measure power parameter respectively, when measured result is shown every time, you must press button to sum in turn. The operation is same as the first phase measurement. (Figure ) 4. Turn the selector to Φ ( to the third phase measurement),hook the clamp jaw around the third phase conductor of the tested circuit, press button and button to measure power parameter respectively, when measured result is shown every time, you must press button to obtain the sum. The operation is the same as the first phase measurement. ( Figure 4) Tested conductor EX- Earth wire k PF RS k V V V COM Black Red Green Yellow ( Figure.The Second Power Measurements ) - -

24 6k Ture RMS UTO RNGE PF HOLD 6V CT.III Tested conductor Earth EX- P k PF V / Hz RS CLER k V V V COM Black Red Green Yellow ( Figure 4. The Third Phase Power Measurements ) 5. fter doing each phase measurement, turn the selector to, the display then shows total ctive Power value and Power Factor value of the three-phase load (Figure 5). fter displaying for three seconds, the display switches to show total pparent Power value and total Reactive Power value automatically(figure 6). The total pparent Power value is in the primary display and the total Reactive Power value is in the secondary display. The display switches automatically every three seconds until you turn the meter to another function. - -

25 6k 6k Ture RMS UTO RNGE V / Hz PF Ture RMS UTO RNGE V / Hz PF P 4 HOLD RS 6 8 CLER HOLD CLER 6V CT.III 6V CT.III Tested conductor Earth wire EX- k RS k PF V V V COM Black Red Green Yellow ( Figure5. Total ctive Power Of Three-Phase ) Tested conductor Earth wire EX- P V V V COM Black Red Green Yellow ( Figure6. Total pparent Power Of Three-Phase ) - -

26 6k Ture RMS UTO RNGE V / Hz PF P RS HOLD CLER 6V CT.III Measuring Three-Phase Three-ire Circuit In three-phase three-wire circuit, the operation of the selector and function button is the same as the operation in three-phase four-wire circuit except the connection of test leads.(figure 7) Tested conductor PF k EX k V V V COM Red Green Yellow ( Figure 7.Power Measurements Of Three-Phase Three-ire) Saving Measurement In measurement mode, you can press button to save the present display to a memory location. The meter can store 8 groups of measurement date. hen the meter has saved 8 groups of date, you press button to save again, the display shows FUL symbol to prompt full memory in the meter now. You must press button to clear the memory and continue saving new date. CLER Recalling Memory If something is saved in the meter memory, use the following procedure to display of a memory location:. Turn the selector to

27 OPTICL INTERFE RS-C. The display shows and HOLD symbol, location number and date in current memory location.. Press button and button to cycle through memory location. RSC Data Interface Connect RSC interface cable to the clamp meter as shown in Figure 8, and then rotate the interface cable deasil to lock it in the meter. Connect the other plug of the interface cable to a serial port of a computer. Then the meter can transmit measured data to computer by the infrared photoelectricity RSC interface in real-time mode. If you want to take out the interface cable from the meter, first you must rotate the cable widdershins to unlock it, then you can pull it out. You will install the special data record software into the computer according to REDME.TEXT file in SETUP disk. hen the meter is in measurement mode, press RS button, you can record and print the measured data of the meter in real time mode in the INDOS. The software can record, plot, print data and curve. OPTICL INTERFE RS ~ 6V COMPUTER ( Figure 8. RSC Interface Cable Connection ) - 5 -

28 Input Voltage nd Current hen the meter is in power measurement mode, if input voltage exceeds 6V(TRMS)or current exceeds (TRMS), the meter will display OL symbol, and bar graph is full. hen input voltage exceeds V, the symbol is shown in the display for safety. Backlight Display hen pressing button, backlight of LCD display is on. fter lighting for 4 seconds the backlight is self-off. Sketch Of Safety Holding Use the wrist-webbing to prevent an accidental drop as shown in Figure 9. OPEN RNING PLESE RED MNUL FOR SFETY.TO VOID ELECTRICL SHOCK NEVER CONNECT THE TEST LEDS TO THE INPUT JKS HICH RE NOT FORRELTED MESURING ND REMOVE LL INPUTS BEFORE OPENING CSE. BTTERIES : 4 X.5 V SIZE IEC- IEC-- 6V CT.III POLLUTION DEGREE ( Figure 9 ) - 6 -

29 V I Curve Diagram Of Power ( PF=K / KV ) +E +I +P PEK VLUE OF POER E=4V PEK VLUE -E -I -P TIVE POER POER 9 8 X 6 I=4 PEK VLUE ( Figure. PF=) +V +I +P P 5 X TIVE POER K= I R -E -I -P θ θ 45 8 PEK VLUE ( Figure ) +V +I P +P V +V +i I k=i R 8 X -E -I -P θ θ -i -V 6 ( Figure ) - 7 -

30 IEC- IEC-- 6V CT.III POLLUTION DEGREE Low Voltage Indication The " " symbol is shown on the top right of the LCD display, when the batteries are weak, you need replace new batteries or use the EX- P function of the meter. Turn the selector to EX- P, the meter will use the measured voltage signal as power supply to work. But the meter can only measure a single-phase circuit and cannot work with a three-phase circuit in this power source mode. Replacing Batteries RNING To avoid electrical shock, the instrument must be powered off and the lest leads or any input signals disconnected before replacing the batteries. Never use the instrument unless the back cover of the instrument is fastened completely. Replace batteries only with same type or rating. Coin OPEN RNING PLESE RED MNUL FOR SFETY.TO VOID ELECTRICL SHOCK NEVER CONNECT THE TEST LEDS TO THE INPUT JKS HICH RE NOT FORRELTED MESURING ND REMOVE LL INPUTS BEFORE OPENING CSE. OPEN RNING PLESE RED MNUL FOR ELECTRICL SHOT BTTERIES : 4 X.5 V SIZE ( Figure. Open The Battery Cover ) - 8 -

31 hen the LCD displays the symbol, the batteries must be replaced to maintain proper operation. Use the following procedure to replace the batteries:. Disconnect test leads from any signals, turn the rotary function switch to, and remove the test leads from the input terminals.. Open the battery cover and remove the battery cover. Because there is a locked design in the battery cover, do not force the battery cover open, otherwise the cover may break. Refer to Figure for opening it: Insert a coin into the groove of the battery cover, press the coin down, then open the cover.. Remove old batteries and replace with new batteries which are the same type or rating. 4. Reinstall the battery cover. SPECIFICTIONS VOLTGE RMS RNGE CURY RESOLUTION INPUT IMPEDNCE V ±(.%+5).V MΩ V ±(.%+5).V (Pf SHUNT) 6V ±(.%+5).V Max. Overload Voltage:75V (RMS) - 9 -

32 CURRENT RMS RNGE CURY RESOLUTION 4 ±(%+5). ±(%+5). 4 ±(%+5). ±(%+5). Max. Overload Current:5 TIVE POER ( ) RNGE CURY RESOLUTION 4k ±(%+5).k k ±(%+5).k 4k ±(%+5).k k ±(%+5).k 6k ±(%+5).k Minimum measurement current : 5 Minimum measurement voltage : V PPRENT POER (V) RNGE CURY RESOLUTION 4 ±(%+5). ±(%+5). 4 ±(%+5). ±(%+5). 6 ±(%+5). Minimum measurement current : 5 Minimum measurement voltage : V - -

33 POER FTOR (PF) RNGE CURY RESOLUTION.~ Capacitive ±(.+)..~ Inductive ±(.+). Minimum measurement current : 5 Minimum measurement voltage : V RETIVE POER (Var) =(V) + RNGE CURY RESOLUTION 4 ±(4%+5). ±(4%+5). 4 ±(4%+5). ±(4%+5). 6 ±(4%+5). Minimum input current : 5 Minimum input voltage : V Recording Voltage value current value ctive Power value to calculate Reactive Power value, The calculating accuracy is.% of the range. TIVE ENERGY () RNGE CURY RESOLUTION ~9999 ±(%+). Minimum measurement current :.5 Minimum measurement voltage : V - -

34 FREQUENCY ( Hz ) RNGE CURY RESOLUTION Hz~kHz.5%.Hz Minimum measurement voltage: V * ccuracy:% of reading + number of digits The specification given assume an operating temperature: 8 ~8,humidity up to: 8%, the frequency of voltage and current is 45Hz~65Hz * Maximum common made voltage: 6V RMS * Display : LCD 9999 * Range : autorange * Overrange indication: Figure OL on the display * Reading Holding: Figure on the display * Power supply : 4.5V * Power consume: 5m * Storage temperature: - ~7 * Operating temperature: ~4 * Dimension size: mm mm 5mm * eight: approx. 5g ( include battery ) CESSORIES Users manual Battery.5V 4 Test Leads (MS) Connect test clamp (MS) RSC interface cable ( MS4 ) PC Data Record graph software Carry Case - -

USING THE INSTRUMENT

USING THE INSTRUMENT PHSE DIGITL POER CLMP METER Safety Precautions Read these operation instructions thoroughly and completely before operating your meter. Pay particular attention to RNING. The instructions in these warnings

More information

3 PHASE DIGITAL POWER CLAMP METER USERS MANUAL

3 PHASE DIGITAL POWER CLAMP METER USERS MANUAL PHASE DIGITAL POWER CLAMP METER USERS MANUAL CONTENTS Safety Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - Safety Information - - - - - - - - - - - - - - - - - - - - - - - - - - - Safety

More information

AC/DC CLAMP METER USER S MANUAL

AC/DC CLAMP METER USER S MANUAL AC/DC CLAMP METER USER S MANUAL CONTENTS PAGE SAFETY INFORMATION SYMBOL EXPLANATION SAFETY PRECAUTIONS 1 1 2 MAINTENANCE 3 GENERAL DESCRIPTION 4 PANEL DESCRIPTION 4 OPERATING INSTRUCTIONS... 7 SPECIFICATIONS

More information

OPERATOR S INSTRUCTION MANUAL

OPERATOR S INSTRUCTION MANUAL OPERATOR S INSTRUCTION MANUAL AUTO-RANGE DUAL DISPLAY CONFORMED IEC1010 DIGITAL MULTIMETER CONTENTS PAGE SAFETY INFORMATION..... DESCRIPTION.. OPERATING INSTRUCTION.. SPECIFICATIONS.... ACCESSORIES. BATTERY

More information

Model UT233 OPERATING MANUAL

Model UT233 OPERATING MANUAL Model UT233 OPERATING MANUAL TABLE OF CONTENTS TITLE PAGE Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical Symbols The Meter Structure A. The Meter Front

More information

UT232. Operating Manual. Digital Power Clamp Meter

UT232. Operating Manual. Digital Power Clamp Meter UT232 Operating Manual Digital Power Clamp Meter Model UT232 OPERATING MANUAL TABLE OF CONTENTS TITLE PAGE Overview Unpacking Inspection Safety Information Rules For Safe Operation International Electrical

More information

AC/DC DIGITAL CLAMP METER OPERATION MANUAL

AC/DC DIGITAL CLAMP METER OPERATION MANUAL AC/DC DIGITAL CLAMP METER OPERATION MANUAL HYS005661 A0 ACCESSORIES 6. ACCESSORIES 1) Test Leads: Electric Ratings 1000V 10A 1 pair (set) 2) Operating Manual 1 copy 3) 1.5V AAA Battery 3 piece - - 55 -

More information

MANUAL PCE-UT232

MANUAL PCE-UT232 www.pce-group-europe.com PCE- Deutschland Gmb H & Co. KG Tel: +49 029 03 976 99-0 Fax: +49 029 03 976 99-29 info@warensortiment.de www.warensortiment.de PCE Group Ibérica S.L. Tel: +34 967 543 548 Fax:

More information

Multifunction Digital

Multifunction Digital MS2009A Multifunction Digital Clamp Meter User Manual 200/600 OFF 2/20 NCV SEL MAX V RAN HOLD OFF MS2009A AC CLAMP METER AUTO MAX C F kmω μmva CONTENTS Safety requirements...1 Safety signs...1 Notes...1

More information

AMM-1022 Digital Multimeter USER`S MANUAL

AMM-1022 Digital Multimeter USER`S MANUAL Digital Multimeter USER`S MANUAL www.tmatlantic.com CONTENTS 1. SAFETY INFORMATION.3 2. DESCRIPTION..6 3. SPECIFICATIONS.8 4. OPERATING INSTRUCTION..11 4.1 Voltage measurement...11 4.2 Current measurement

More information

USER MANUAL Clamp Meters ACM-2353

USER MANUAL Clamp Meters ACM-2353 USER MANUAL Clamp Meters ACM-2353 www.tmatlantic.com Overview This Operating Manual covers information on safety and cautions. Please read the relevant information carefully and observe all the Warnings

More information

DIGITAL MULTIMETER INSTRUCTION MANUAL

DIGITAL MULTIMETER INSTRUCTION MANUAL DIGITAL MULTIMETER INSTRUCTION MANUAL 1 CONTENTS CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 3 1.4 MAINTENANCE 4 2. DESCRIPTION 5 2.1 NAMES OF COMPONENTS 5 2.2 SWITCH,

More information

EM420A/420B DIGITAL MULTIMETER OWNERS MANUAL Read this owners manual thoroughly before use

EM420A/420B DIGITAL MULTIMETER OWNERS MANUAL Read this owners manual thoroughly before use http://www.all-sun.com EM420A/420B DIGITAL MULTIMETER OWNERS MANUAL V Read this owners manual thoroughly before use WARRANTY This instrument is warranted to be free from defects in material and workmanship

More information

DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A OPERATION MANUAL

DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A OPERATION MANUAL DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A OPERATION MANUAL DIGITAL DUAL DISPLAY AC/DC CLAMP METER MODEL-860A TABLE OF CONTENTS TITLE PAGE Safety Information Safety Symbols... 1 Meter Description...

More information

Model DIGITAL MULTIMETER

Model DIGITAL MULTIMETER Model 57070 DIGITAL MULTIMETER INSTRUCTION MANUAL SAFETY INFORMATION To ensure safe operation, and in order to exploit to the full the functionality of the meter, please follow the directions in this section

More information

UT231. Operating Manual. Digital Power Clamp Meter P/N:

UT231. Operating Manual. Digital Power Clamp Meter P/N: UT231 Operating Manual Digital Power Clamp Meter P/N: 41451518 Model UT231 OPERATING MANUAL TABLE OF CONTENTS TITLE PAGE Overview Unpacking Inspection Safety Information Rules For Safe Operation International

More information

DVM1190 DIGITAL MULTIMETER

DVM1190 DIGITAL MULTIMETER DIGITAL MULTIMETER 1. Introduction Thank you for buying the. This digital multimeter has a large LCD, a data-hold function and a backlight. The device uses a very practical safety mechanism that keeps

More information

Digital clamp meter AX-3550

Digital clamp meter AX-3550 Digital clamp meter AX-3550 Instruction Manual 1. Safety Information To avoid possible electric shock or personal injury, and to avoid possible damage to the Meter or to the equipment under test, adhere

More information

PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D

PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D PEN TYPE DIGITAL MULTIMETER OPERATION MANUAL T8211D T8211D 1 1. SAFETY INFORMATION BE EXTREMELY CAREFUL IN THE USE OF THIS METER. Improper use of this device can result in electric shock or destroy of

More information

MS6231 DIGITAL ENGINE ANALYZER OPERATOR S MANUAL CONTENTS CONTENTS

MS6231 DIGITAL ENGINE ANALYZER OPERATOR S MANUAL CONTENTS CONTENTS CONTENTS MS6231 DIGITAL ENGINE ANALYZER OPERATOR S MANUAL CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 2 1.2 DURING USE 3 1.3 SYMBOLS 5 1.4 MAINTENANCE 6 2. DESCRIPTION 8 2.1 NAMES OF COMPONENTS 9

More information

DIGIT & POINTER MULTIMETER

DIGIT & POINTER MULTIMETER CONTENTS DIGIT & POINTER MULTIMETER OPERATOR S MANUAL 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 3 1.4 MAINTENANCE 3 2. DESCRIPTION 4 2.1 NAMES OF COMPONENTS 4 2.2 FUNCTION

More information

600 AAC Clamp Meter Instruction Manual

600 AAC Clamp Meter Instruction Manual C Clamp Meter Instruction Manual #1-744 # WRNING Read First: Safety Information Understand and follow operating instructions carefully. Use the meter only as specified in this manual; otherwise, the protection

More information

MS8211 DIGITAL MULTIMETER INSTRUCTION MANUAL

MS8211 DIGITAL MULTIMETER INSTRUCTION MANUAL MS8211 DIGITAL MULTIMETER INSTRUCTION MANUAL Ω CONTENTS CONTENTS 1. SAFETY INFORM...1 4.4 Range Transform...10 1.1 Preliminary...1 4.5 Auto Power Off...10 1.2 During use...2 4.6 Preparation For Measurement...11

More information

1. SAFETY INFORMATION.1 2. DESCRIPTION SPECIFICATIONS.6 4. OPERATING INSTRUCTION Voltage measurement Current measurement 10

1. SAFETY INFORMATION.1 2. DESCRIPTION SPECIFICATIONS.6 4. OPERATING INSTRUCTION Voltage measurement Current measurement 10 CONTENTS 1. SAFETY INFORMATION.1 2. DESCRIPTION..4 3. SPECIFICATIONS.6 4. OPERATING INSTRUCTION..9 4.1 Voltage measurement...10 4.2 Current measurement 10 4.3 Resistance measurement...12 4.4 Diode test.12

More information

OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER

OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL DIGITAL MULTIMETER SAFETY INFORMATION This multimeter has been designed according to IEC 1010 concerning electronic measuring instruments with an overvoltage category (CATⅡ)

More information

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use True RMS Digital Multimeter DVM98 1 Safety information This multimeter has been designed according to IEC - 1010 concerning electronic measuring instruments with an overvoltage category (CAT II) and pollution

More information

OPERATOR S INSTRUCTION MANUAL M-2625 AUTO RANGING DIGITAL MULTIMETER

OPERATOR S INSTRUCTION MANUAL M-2625 AUTO RANGING DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL M-2625 AUTO RANGING DIGITAL MULTIMETER with Temperature Probe Copyright 2007 Elenco Electronics, Inc. Contents 1. Safety Information 3,4 2. Safety Symbols 5 3. Front Plate

More information

OPERATING INSTRUCTION

OPERATING INSTRUCTION OPERATING INSTRUCTION AUTOMOTIVE MULTIMETER MODEL QM1444 the finger guards on the probes. Measuring voltage which exceeds the limits of the multimeter may damage the meter and expose the operator to a

More information

Model ST Instruction Manual. True RMS Autoranging Digital Multimeter. reedinstruments. www. com

Model ST Instruction Manual. True RMS Autoranging Digital Multimeter. reedinstruments. www. com Model ST-9933 True RMS Autoranging Digital Multimeter Instruction Manual reedinstruments com Table of Contents Safety... 3 Features... 4 Specifications...4-8 Technical...4-5 Accuracy...5-8 Display Description...

More information

NOTE: Fully read and understand this manual before using this Digital Multimeter.

NOTE: Fully read and understand this manual before using this Digital Multimeter. ASTROAI USER MANUAL AUTO RANGING DIGITAL CLAMP METER Thank you for purchasing the Auto Ranging Digital Clamp Meter from AstroAI. The AstroAI Auto Ranging Digital Clamp Meter is designed to be safely and

More information

Thank you again for choosing AstroAI, if you have any questions or concerns regarding your product, please contact us at

Thank you again for choosing AstroAI, if you have any questions or concerns regarding your product, please contact us at ASTROAI USER MANUAL DT132A 4000 Count Auto-Ranging Multimeter Thank you for purchasing the AstroAI DT132A 4000 Count Auto-Ranging Multimeter. It is a 3 ¾ digit, 3999 counts, auto-ranging digital multimeter.

More information

USER MANUAL 600A AC Clamp Meter + NCV Model MA610

USER MANUAL 600A AC Clamp Meter + NCV Model MA610 USER MANUAL 600A AC Clamp Meter + NCV Model MA610 Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech MA610 Clamp Meter. This meter measures

More information

ATK Clamp Meter

ATK Clamp Meter ATK-2209 Clamp Meter User s Manual Title CONTENTS Page I. SAFETY INFORMATION... 1 II. TECHNICAL SPECIFICATIONS... 2 2-1 Environment Conditions... 2 2-2 Maintenance... 2 2-3 Features... 2 2-4 General Specifications...

More information

MS8250A/B OPERATION MANUAL MS8250A. Hz% FUNC REL RANGE REL HOLD OFF 10A. Hz% A NCV. Hz% COM. A ma 10A FUSED 600V CAT IV.

MS8250A/B OPERATION MANUAL MS8250A. Hz% FUNC REL RANGE REL HOLD OFF 10A. Hz% A NCV. Hz% COM. A ma 10A FUSED 600V CAT IV. MS8250A/B DIGITAL MULTIMETER OPERATION MANUAL AUTO DC AC REL hfe PCLINK % C F kmωkz nµmfav MS8250A DIGITAL MULTIMETER Auto Power Off RANGE REL HOLD FUNC NCV A ma OFF 10A A ma 10A FUSED 600V CAT IV COM

More information

MS8216 DIGITAL MULTIMETER OPERATOR S MANUAL

MS8216 DIGITAL MULTIMETER OPERATOR S MANUAL MS8216 DIGITAL MULTIMETER OPERATOR S MANUAL CONTENTS 1. SAFETY INFORMATION 1 1.1 PRELIMINARY 1 1.2 DURING USE 2 1.3 SYMBOLS 4 1.4 MAINTENANCE 4 2. DESCRIPTION 5 2.1 NAMES OF COMPONENTS 5 2.2 FUNCTION AND

More information

DVM645BI BENCH MULTIMETER TAFELMULTIMETER MULTIMETRE DE TABLE BANCO MULTÍMETRO TISCHMULTIMETER. User Manual. Gebruikershandleiding

DVM645BI BENCH MULTIMETER TAFELMULTIMETER MULTIMETRE DE TABLE BANCO MULTÍMETRO TISCHMULTIMETER. User Manual. Gebruikershandleiding BENCH MULTIMETER TAFELMULTIMETER MULTIMETRE DE TABLE BANCO MULTÍMETRO TISCHMULTIMETER User Manual Gebruikershandleiding Manuel d'utilisation Gebrauchsanleitung Introduction BENCH MULTIMETER This manual

More information

MW3105 DIGITAL CLAMP MULTIMETER

MW3105 DIGITAL CLAMP MULTIMETER MW3105 DIGITAL CLAMP MULTIMETER 2 M MW3105 A 01 INTRODUCTION 1.1 - Unpacking and inspection Upon removing your new Digital Clamp Meter from its packing, you should have the following items: 1. Digital

More information

MS2030 CAT III 600 V A V AUTO RS232

MS2030 CAT III 600 V A V AUTO RS232 MS2030 AC Digital Clamp Meter User s Manual CAT III 600 V AUTO RS232 A V CONTENTS 1.Introduction...1 2.Safety Information...1 2.1 Precautions...1 2.2 Safety Symbols...3 3. Description...4 3.1 Front Panel...4

More information

ET-3888 True RMS Clamp Meter. User Manual

ET-3888 True RMS Clamp Meter. User Manual ET-3888 True RMS Clamp Meter User Manual Index Introduction... 3 Safety Notes... 4 Features... 5 Specifications... 6-8 Instrument Layout... 9 Measurement... 10 Maintenance... 11 Page 2 1. Introduction

More information

OPERATOR S INSTRUCTION MANUAL

OPERATOR S INSTRUCTION MANUAL 2 OPERATOR S INSTRUCTION MANUAL CLAMP METER HOLD 20 A 200 A 2 A 600 600 LIGHT ON/OFF Digital Clamp Meter 2 20 200 A khz COM CAT.II MAX 600 CONTENTS 1. General instruction.....1 2. Description...1 2.1 Precautions

More information

DIGITAL MULTIMETER CONTENTS DIGITAL MULTIMETER CONTENTS

DIGITAL MULTIMETER CONTENTS DIGITAL MULTIMETER CONTENTS CONTENTS CONTENTS CONTENTS 1. SAFETY INFORMATION...1 1.1 Preliminary...1 1.2 Dos and don ts...2 1.3 Symbols...3 1.4 Precautions...4 2. DESCRIPTION...5 2.1 Names of parts...6 2.2 Switches, buttons and input

More information

AX-C Introduction. 2. Safety Information

AX-C Introduction. 2. Safety Information AX-C708 1. Introduction Read Safety Information before using the meter. ProcessMeter ( referred to as the meter )is a handheld, battery-operated tool for measuring electrical parameters. It has all the

More information

MM700. True RMS ENGLISH. INSTRUCTION MANUAL Auto-Ranging. Measurement Technology

MM700. True RMS ENGLISH. INSTRUCTION MANUAL Auto-Ranging. Measurement Technology INSTRUCTION MANUAL Auto-Ranging Digital Multimeter er True RMS Measurement Technology MM700 DATA & RANGE HOLD LOW IMPEDANCE AUDIBLE CONTINUITY MIN / MAX / RELATIVE TEMPERATURE DIODE TEST CAPACITANCE &

More information

MODEL: D03128 CLAMP METER

MODEL: D03128 CLAMP METER MODEL: D03128 CLAMP METER 1 CONTENTS Page Number Details 3 Important Safety Information 3 Features 4 Product Overview 5 Switches, Buttons & Input Jacks 5 LCD 6 Specifications 6 Electrical Specifications

More information

AC Clamp Meter + Phase Rotation Tester

AC Clamp Meter + Phase Rotation Tester User's Manual AC Clamp Meter + Phase Rotation Tester Model 380974 Hz Introduction Congratulations on your purchase of the Extech 380974 AC Clamp Meter + Phase Rotation Tester. This professional 1000A Clamp

More information

DIGITAL CLAMP METER Use s Manual

DIGITAL CLAMP METER Use s Manual MS2026 MS2026R DIGITAL CLAMP METER Use s Manual MS2026 FUNC. RANGE MAX/MIN Hz/% HOLD AC CLAMP METER Auto Range AUTO DC AC MAX MIN REL μnf %Hz kmω mva CAT III 600 V CONTENTS 1. Safety Information...1 1.1

More information

Keysight U1241C/ U1242C Handheld Digital Multimeter. Quick Start Guide

Keysight U1241C/ U1242C Handheld Digital Multimeter. Quick Start Guide Keysight U4C/ U4C Handheld Digital Multimeter Quick Start Guide Safety Notices CUTION CUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly

More information

Instruction Manual for Digital Grounding Resistance Meter

Instruction Manual for Digital Grounding Resistance Meter Instruction Manual for Digital Grounding Resistance Meter Instruction Manual for Digital Grounding Resistance Meter Table of Contents I. Overview...2 II. Open-case Inspection...3 III. Safety Precautions...4

More information

Digital Multimeter with Backlight

Digital Multimeter with Backlight MODEL: D03126 Digital Multimeter with Backlight 1 CONTENTS Page Number Description 3 Important Safety Information 3 What s Included? 4 Overview 4 Front Panel Description 5 General Specification 5 DC Voltage

More information

User Manual Digital Clamp Multimeter. model no.: MSR-C600

User Manual Digital Clamp Multimeter. model no.: MSR-C600 User Manual Digital Clamp Multimeter model no.: MSR-C600 Overview This Operating Manual covers information on safety and cautions. Please read the relevant information carefully and observe all the Warnings

More information

Dawson DDM190. Digital Multimeter User s Manual

Dawson DDM190. Digital Multimeter User s Manual Dawson DDM190 Digital Multimeter User s Manual TABLE OF CONTENTS LIMITED WARRANTY AND LIMITATION OF LIABILITY... 3 Out of the Box... 3 Accessories.. Error! Bookmark not defined. Safety Information... 7

More information

User Manual Digital Multimeter

User Manual Digital Multimeter User Manual Digital Multimeter model no.: MSR-R500 Questions or Concerns? support@etekcity.com visit etekcity.com for more products Safe and Proper Usage Thank you for purchasing the Etekcity MSR-R500

More information

770E DIGITAL MULTIMETER OPERATOR S MANUAL

770E DIGITAL MULTIMETER OPERATOR S MANUAL 770E DIGITAL MULTIMETER OPERATOR S MANUAL TABLE OF CONTENTS 1.Overview... 1 2.Panel Layout...1/2 3. Safety information... 2 4. Specical cautions for operation.... 2 5.General specifications...2/3 6.Testing

More information

MM700. INSTRUCTION MANUAL Auto-Ranging Digital Multimeter True RMS

MM700. INSTRUCTION MANUAL Auto-Ranging Digital Multimeter True RMS INSTRUCTION MANUAL Auto-Ranging Digital Multimeter True RMS Measurement Technology MM700 DATA & RANGE HOLD LOW IMPEDANCE AUDIBLE CONTINUITY MIN / MAX / RELATIVE TEMPERATURE DIODE TEST CAPACITANCE & FREQUENCY

More information

PCMT20 PYLE C;",D J WWWPYLEAUDIO.COM

PCMT20 PYLE C;,D J WWWPYLEAUDIO.COM PCMT20 PYLE C;",D J @~:@F WWWPYLEAUDIO.COM OPERATING INSTRUCTION AC CLAMP METER Safety International Safety Symbols ~ This symbol, adjacent to another symbol or terminal, indicates the user must refer

More information

Mini Clamp Meter Model:

Mini Clamp Meter Model: Mini Clamp Meter Model: 72-2985 1 CONTENTS Page Number Details 2 What s Included 3 Important Safety Information 3 Technical Specification 4 Product Overview 5 LCD Overview 6 Operation - AC/DC Voltage Measurement

More information

Model 77 Series IV. Digital Multimeter. Users Manual

Model 77 Series IV. Digital Multimeter. Users Manual Model 77 Series IV Digital Multimeter Users Manual Model 77 Series IV Digital Multimeter The Fluke Model 77 Series IV is a battery-powered, average responding-rms indicating multimeter (hereafter "the

More information

Digital Clamp Meter (TRMS) Model : 2727

Digital Clamp Meter (TRMS) Model : 2727 Digital Clamp Meter (TRMS) Model : 2727 Instruction Manual 1. SPECIFICATIONS 1.1 General Specifications Display : 3 ¾ digit liquid crystal display (LCD) with a maximum reading of 3999. Polarity : Automatic,

More information

Contents 1. General instructions. 1.1 Precautions safety measures Protection mechanisms. 2. Description. 2.1 Instrument Familiarization. 2.

Contents 1. General instructions. 1.1 Precautions safety measures Protection mechanisms. 2. Description. 2.1 Instrument Familiarization. 2. Contents 1. General instructions. 1.1 Precautions safety measures... 1.2 Protection mechanisms. 2. Description. 2.1 Instrument Familiarization. 2.2 LCD Display 2.3 Keypad. 3. Function description. 3.1

More information

Compact Autoranging Clamp Meters. Models (400 A AC), (400 A AC/DC)

Compact Autoranging Clamp Meters. Models (400 A AC), (400 A AC/DC) User Manual Compact Autoranging Clamp Meters with NIST-Traceable Calibration Models 20250-55 (400 A AC), 20250-56 (400 A AC/DC) THE STANDARD IN PRECISION MEASUREMENT 1065DGMAN_20250-55,-56 DS Clamp Meter

More information

DM-46 Instruction Manual

DM-46 Instruction Manual Auto Meter Products Inc. Test Equipment DM-46 Instruction Manual Automotive Multimeter and Inductive Amp Probe The DM-46 is the auto industry s answer to pocket portability in a 20 2650-1552-00 3/8/11

More information

USER MANUAL. Model MA A AC Mini Clamp-on Meter. Additional User Manual Translations available at

USER MANUAL. Model MA A AC Mini Clamp-on Meter. Additional User Manual Translations available at USER MANUAL Model MA150 200A AC Mini Clamp-on Meter Additional User Manual Translations available at www.extech.com Introduction Thank you for selecting the Extech MA150 AC Mini Clamp Meter. This device

More information

Dawson DDM230C. True RMS Multimeter with Bar Graph Display User s Manual

Dawson DDM230C. True RMS Multimeter with Bar Graph Display User s Manual Dawson DDM230C True RMS Multimeter with Bar Graph Display User s Manual Table of Contents LIMITED WARRANTY AND LIMITATION OF LIABILITY... 3 Out of the Box... 3 Accessories... 4 Safety Information... 4

More information

User s Guide. 400A AC/DC Clamp Meter. Model MA Washington Street Melrose, MA Phone Toll Free

User s Guide. 400A AC/DC Clamp Meter. Model MA Washington Street Melrose, MA Phone Toll Free User s Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 400A AC/DC Clamp Meter Model MA220 Introduction Thank you for selecting

More information

CL900. True RMS 1000V 2000A 60MΩ ENGLISH. INSTRUCTION MANUAL 2000A Digital Clamp Meter. Measurement Technology

CL900. True RMS 1000V 2000A 60MΩ ENGLISH. INSTRUCTION MANUAL 2000A Digital Clamp Meter. Measurement Technology ENGLISH INSTRUCTION MANUAL 2000A Digital Clamp Meter True RMS Measurement Technology NON-CONTACT VOLTAGE TESTING INRUSH CURRENT LOW IMPEDANCE DATA HOLD RANGE HOLD AUDIBLE CONTINUITY DIODE TEST CAPACITANCE

More information

MS8268 HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL

MS8268 HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL MS8268 HANDHELD DIGITAL MULTIMETER OPERATOR S INSTRUCTION MANUAL Table of Contents TITLE PAGE 1. GENERAL INSTRUCTIONS 1 1.1 Precaution safety measures 1 1.1.1 Preliminary 1 1.1.2 During use 2 1.1.3 Symbols

More information

Model UT511 OPERATING MANUAL

Model UT511 OPERATING MANUAL Model UT511 OPERATING MANUAL TITLE PAGE Introduction Unpacking the Meter Safety Information International Electrical Symbols Battery Saver (Sleep Mode) Battery Indication The Meter Structure Display Key

More information

CONTENTS MS2033A. 1.Introduction Safety Information...01

CONTENTS MS2033A. 1.Introduction Safety Information...01 MS2033A AC Digital Clamp Meter User s Manual CAT III 600 V CONTENTS 1.Introduction...01 2.Safety Information...01 2.1 Precautions...02 2.2 Safety Symbols...03 3. Description...04 3.1 Front Panel...04 3.2

More information

Digital Clamp Meter Model: &

Digital Clamp Meter Model: & Digital Clamp Meter Model: 72-7224 & 72-7226 1 SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This meter is designed to meet IEC61010-1, 61010-2-032,

More information

DM-46 Instruction Manual

DM-46 Instruction Manual Test Equipment Auto Meter Products Inc. 413 West Elm Street Sycamore, IL 60178 Service (815) 899-0801 Toll Free (866) 883-TEST (8378) www.autometer.com/test DM-46 Instruction Manual Automotive Multimeter

More information

Digital automotive analyser 13 function with ic

Digital automotive analyser 13 function with ic Digital automotive analyser 13 function with ic Model no: TA201 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and

More information

Digital Clamp Meter. User Manual

Digital Clamp Meter. User Manual Digital Clamp Meter User Manual CM240 WWW.OWON.COM.CN Mar. 2016 edition V1.2 Copyright LILLIPUT Company. All rights reserved. The LILLIPUT's products are under the protection of the patent rights, including

More information

User Manual Digital Multimeter. model no.: MSR-U1000

User Manual Digital Multimeter. model no.: MSR-U1000 User Manual Digital Multimeter model no.: MSR-U1000 This Operating Manual covers information on safety and cautions. Please read the relevant information carefully and observe all the Warnings and Notes

More information

1. GENERAL INSTRUCTIONS Precaution safety measures Preliminary During use Symbols Instructions 4

1. GENERAL INSTRUCTIONS Precaution safety measures Preliminary During use Symbols Instructions 4 Contents TITLE PGE 1. GENERL INSTRUCTIONS 1 1.1 Precaution safety measures 1 1.1.1 Preliminary 1 1.1.2 During use 3 1.2 Symbols 4 1.3 Instructions 4 2. DESCRIPTION 6 2.1 Instrument Familiarization 6 2.2

More information

APPA 300 Series. The Most User-Friendly High Performance Multimeter

APPA 300 Series. The Most User-Friendly High Performance Multimeter APPA 300 Series The Most User-Friendly High Performance Multimeter Throw Away the Manual... So Easy, So Simple Straight Forward... For basic application, simply to operate these keys... "LIGHT" "BAR" "DIGIT"

More information

SAFETY PRECAUTIONS: Before use, read the following safety precautions

SAFETY PRECAUTIONS: Before use, read the following safety precautions [1] SAFETY PRECAUTIONS: Before use, read the following safety precautions This instruction manual explains how to use your multimeter CD731, CD751 safely. Before use, please read this manual thoroughly.

More information

Model EARTH RESISTANCE CLAMP USERS MANUAL EARTH RESISTANCE C L A M P : CAT II. 1mA 20A AL : ~ 600V

Model EARTH RESISTANCE CLAMP USERS MANUAL EARTH RESISTANCE C L A M P : CAT II. 1mA 20A AL : ~ 600V Model 57276 EARTH RESISTANCE CLAMP USERS MANUAL EARTH RESISTANCE C L A M P A A : 600V : 0.01 1200 CAT II AL : 1 100 1mA 20A MEM : 1 99 CONTENTS WARNING - - - - - - - - - - - - - - - - - - - - - - - - -

More information

DIGITAL MULTIMETER AUTORANGING

DIGITAL MULTIMETER AUTORANGING MODEL: D03124 DIGITAL MULTIMETER AUTORANGING 1 CONTENTS Page Number Details 2 Introduction 2 What s Included 3 Important Safety Information 3 Symbol Guide 4 Overview 5 Buttons 5 Display Indicators 6 General

More information

MM V 10A ENGLISH. INSTRUCTION MANUAL Auto-Ranging DATA HOLD AUDIBLE CONTINUITY MIN / MAX TEMPERATURE DIODE TEST CAPACITANCE

MM V 10A ENGLISH. INSTRUCTION MANUAL Auto-Ranging DATA HOLD AUDIBLE CONTINUITY MIN / MAX TEMPERATURE DIODE TEST CAPACITANCE INSTRUCTION MANUAL Auto-Ranging Digital Multimeter MM400 DATA HOLD AUDIBLE CONTINUITY MIN / MAX TEMPERATURE DIODE TEST CAPACITANCE 600V 10A 40MΩ 2 GENERAL SPECIFICATIONS Klein Tools MM400 is an auto-ranging

More information

TRMS LEAKAGE CURRENT CLAMP-ON METER 565

TRMS LEAKAGE CURRENT CLAMP-ON METER 565 TRMS LEAKAGE CURRENT CLAMP-ON METER 565 E N G L I S H User Manual Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument has been calibrated using standards

More information

USER'S MANUAL. ACD-6 Pro. ACD-6 TRMS Pro. Versatile Clamp-on Multimeter Series

USER'S MANUAL. ACD-6 Pro. ACD-6 TRMS Pro. Versatile Clamp-on Multimeter Series USER'S MANUAL ACD-6 Pro ACD-6 TRMS Pro Versatile Clamp-on Multimeter Series 1 1) SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and maintaining

More information

1. SAFETY 1.1. SAFETY INFORMATION 1.2. SAFETY SYMBOLS

1. SAFETY 1.1. SAFETY INFORMATION 1.2. SAFETY SYMBOLS To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

More information

Model φ/1φ Power Clamp-on Meter

Model φ/1φ Power Clamp-on Meter User's Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech 382075 Product Page Model 382075 3φ/1φ Power Clamp-on

More information

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: MODEL: Multimeter Service Information

IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: MODEL: Multimeter Service Information IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-340 MODEL: 61-342 Multimeter Service Information The Service Information provides the following information: Precautions and safety information Specifications

More information

USER'S MANUAL ACDC-100 TRMS ACDC-100. Versatile AC/DC Clamp-on Multimeter Series

USER'S MANUAL ACDC-100 TRMS ACDC-100. Versatile AC/DC Clamp-on Multimeter Series 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com USER'S MANUAL ACDC-100 TRMS ACDC-100 Versatile AC/DC Clamp-on Multimeter Series 1 1) SAFETY This manual contains information

More information

UT207A/208A/209A Operating Manual. Table of Contents

UT207A/208A/209A Operating Manual. Table of Contents Table of Contents Title Overview Unpacking Inspection Safety Information Rules for Safe Operation International Electrical Symbols The Meter Structure Display Symbols Functional Buttons The Effectiveness

More information

DMM8900 SERIES USERS MANUAL

DMM8900 SERIES USERS MANUAL DMM8900 SERIES USERS MANUAL WARRANTY This instrument is warranted to be free from defects in material and workmanship for a period of one year. Any instrument found defective within one year from the delivery

More information

600A Clamp Meters w/tightsight Display

600A Clamp Meters w/tightsight Display V 750V #61-764 #61-766 #61-768 600A Clamp Meters w/tightsight Display Instruction Manual 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com CAT.IV 600V CAT.III 1000V 600A 61-766

More information

Instruction Manual for Digital Grounding Resistance Meter. Table of Contents

Instruction Manual for Digital Grounding Resistance Meter. Table of Contents I. Overview...2 II. Open-case Inspection...3 III. Safety Precautions...4 IV. Work Principle...7 V. Appearance Description...9 VI. Technical Characteristics 10 VII. Resistance Measurement Method..12 VIII.Battery

More information

Digital Automotive Analyser 14 Function With IC

Digital Automotive Analyser 14 Function With IC Digital Automotive Analyser 14 Function With IC Model no: TA202 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and

More information

Dawson DDM181. Pocket-Size Autorange Digital Meter User s Manual

Dawson DDM181. Pocket-Size Autorange Digital Meter User s Manual Dawson DDM181 Pocket-Size Autorange Digital Meter User s Manual 1 Table of Contents LIMITED WARRANTY AND LIMITATION OF LIABILITY... 3 Out of the Box... 3 Accessories... 4 Important Safety Information...

More information

MS2109A AC/DC Clamp Meter. User Manual. Contents

MS2109A AC/DC Clamp Meter. User Manual. Contents MS2109A AC/DC Clamp Meter User Manual Contents 1. Safety information 1 1.1 Preparation 1 1.2 Usage 1 1.3 Signs and Labels 2 1.4 Maintenance 2 2. Description 2 2.1 Part name 3 2.2 Switch and button description

More information

DC/AC CLAMP METER ISO-TECH 2000 USERS MANUAL

DC/AC CLAMP METER ISO-TECH 2000 USERS MANUAL DC/AC CLAMP METER ISO-TECH 2000 USERS MANUAL Warnings and Safety symbols: Caution, refer to this manual before using the meter. Dangerous voltages. Meter is protected throughout by double insulation or

More information

USER MANUAL. Model MA A AC Clamp Meter DMM Model MA445 True RMS 400A AC/DC Clamp Meter DMM

USER MANUAL. Model MA A AC Clamp Meter DMM Model MA445 True RMS 400A AC/DC Clamp Meter DMM USER MANUAL Model MA440 400A AC Clamp Meter DMM Model MA443 True RMS 400 AC Clamp Meter DMM Model MA445 True RMS 400A AC/DC Clamp Meter DMM Introduction Thank you for selecting the Extech EX44x Series

More information

ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL

ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL ETHOS 5030 TRUE-RMS DIGITAL MULTIMETER OPERATION MANUAL 1 1. SAFETY INFORMATION SAFETY SYMBOLS Warning! Dangerous Voltage (Risk of electric shock). Caution! Refer to the user s manual before using this

More information

Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES

Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES Instruction Manual ICM 3091N Digital AC Clampmeter EN FR IT DE ES TABLE OF CONTENTS / EN TITLE TABLE OF CONTENTS PAGE 1. SAFETY INFORMATION... 1 2. TECHNICAL SPECIFICATIONS... 2 3. PARTS & CONTROLS...

More information

USER'S MANUAL. ACD-16 Pro ACD-16 TRMS Pro ACD-40PQ

USER'S MANUAL. ACD-16 Pro ACD-16 TRMS Pro ACD-40PQ USER'S MANUAL ACD-16 Pro ACD-16 TRMS Pro ACD-40PQ 1 1) SAFETY This manual contains information and warnings that must be followed for operating the instrument safely and maintaining the instrument in a

More information

CONTENTS. SAFETY PRECAUTIONS: Before use, read the following safety precautions

CONTENTS. SAFETY PRECAUTIONS: Before use, read the following safety precautions CONTENTS [1] SAFETY PRECAUTIONS: Before use, read the following safety precautions 2 [2] APPLICATION AND FEATURES 5 [3] NAME OF COMPONENT UNITS 6 [4] DESCRIPTION OF FUNCTIONS 8 [5] MEASUREMENT PROCEDURE

More information

79/26 Series III Multimeter

79/26 Series III Multimeter 79/26 Series III Multimeter Instruction Sheet W Read First: Safety Information Never use the meter if the meter or test leads look damaged. Be sure the test leads and switch are in the correct position

More information

User's Guide. 800 Amp AC/DC True RMS Clamp Meter. Model EX Washington Street Melrose, MA Phone Toll Free

User's Guide. 800 Amp AC/DC True RMS Clamp Meter. Model EX Washington Street Melrose, MA Phone Toll Free User's Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 800 Amp AC/DC True RMS Clamp Meter Model EX730 Introduction Congratulations

More information