Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Size: px
Start display at page:

Download "Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment"

Transcription

1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED LEASING/MONTHLY RENTALS ITAR CERTIFIED SECURE ASSET SOLUTIONS SERVICE CENTER REPAIRS Experienced engineers and technicians on staff at our full-service, in-house repair center SM InstraView REMOTE INSPECTION Remotely inspect equipment before purchasing with our interactive website at Contact us: (888) 88-SOURCE WE BUY USED EQUIPMENT Sell your excess, underutilized, and idle used equipment We also offer credit for buy-backs and trade-ins LOOKING FOR MORE INFORMATION? Visit us on the web at for more information on price quotations, drivers, technical specifications, manuals, and documentation

2 Contactor System Suppressor Auxiliary contact modul (side mounting) Contactor Pneumatic timer module Auxiliary contact modules (front mounting) 4th -pole Thermal overload relay IEC 947, EN J7K Contactor Range from 4 to 7 kw (AC--, 80/440 V). Seven contactor frame sizes, with 2 ratings each (except for J7K--AMA). Main contacts with -- and 4--pole. Both AC-- and DC--type available (Base area is same but DC is always 2 mm deeper, except for J7K--AMA, J7K--FM(A) and J7K--GM(A)). 4 mm width up to J7K--CMA, 11 kw (at 80/440 V AC). Finger proof protection. All terminals supplied open, ready to connect. J7TK Overload Relays Three frame sizes adapting complete contactor range. For separate mounting. Can be mounted directly. Single phasing sensitivity according to IEC J7K Auxiliary Contact Modules Up to four auxiliary contact modules. Contacts can be fitted to the side (not J7K--BM(A)). Interlocked opposing contacts. Suitable for electronic devices (for J7K--AMA). Safe isolation to IEC 6 between the contacts. Top and side mounting (for J7K--CM(A) to J7K--EM(A)) 2--pole/4--pole with various contact combinations. Accessories Suppressors. Mechanical interlocks. Single coils 1

3 Ordering Information Model Number Legend: Contactor: J7K - jjj - j - j j Frame size: A, B, C, D, E, F, G 2. Application: M = motor load. Rating: Standard = none, high = A 4. Int. auxiliary contacts: -01, pole: - 4. Coil type: DC or AC (AC = none, DC = D) 6. Coil voltages: Standard voltages AC 24V 0Hz 48V 0Hz 110V 0Hz / 120V 60Hz 20V 0Hz / 240V 60Hz 41V 0Hz / 480V 60Hz 110V 0Hz / 60Hz 20V 0Hz / 60Hz DC 24V DC 48V DC 60V DC 220V DC Auxiliary contact modules: J7K - jj - j j Frame size: If used for more than one frame size. Onlythelowestframe:A,B,C,F 2. Application: nothing: universal use, M: use only for M -contactor. No. of contacts and configuration: 11, 22, 02, etc. 4. Mounting: S = side mounting SI, SA = side mounting, in/outside nothing = top mounting SID = side mounting inside, with early make and late break contacts Accessories for contactors: J7K - j - j Frame size of the contactor: If used for more than one frame size: Onlythelowestframe:A,B,C,D,E,F 2. Type of accessories: RC 20: RC suppressor 20V AC FD: Diode suppressor VG 20: Varistor suppressor 20V VG 41: Varistor suppressor 41V MV: Mechanical interlock N: 4th -pole PTE -11: Pneumatic timer module (ON -delayed) PTD -11: Pneumatic timer module (OFF -delayed) Single coils: J7KB -IC - j - j Accessories for overload relays: J7TK - j - j Coil type: AC or DC (AC = none, DC = D) 2. Coil voltages Standard voltages: AC 24V 0Hz 48V 0Hz 110V 0Hz / 120V 60Hz 20V 0Hz / 240V 60Hz 41V 0Hz / 480V 60Hz 110V 0Hz / 60Hz 20V 0Hz / 60Hz DC 24V DC 48V DC 60V DC 220V DC 1. Frame size of overload relays: BorD 2. Type of accessory: B=Base Thermal overload relays: J7TK - j - j - j Frame size: If used for more than one contactor frame size: Onlythelowestframe:B,D,F 2. Setting current: 0.4 to 10 A. Optional kind of terminals: FB = box terminal (for separate mounting equal to J7K -F) FP = (one side) pin terminal (for direct mounting on J7K -F) GB = boxterminal (for separate mounting equal to J7K -G) GP = (one side) pin terminal (for direct mounting on J7K -G) 2

4 Available types J7K -AMA Type Contactor Voltage AC J7K -AMA V 0Hz / 240V 60Hz J7K -AMA -10 J7K - AMA V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K-AMA-01-D 24V DC J7K-AMA-10-D J7K - AMA D 48V DC 60V DC 220V DC J7K -BM(A) Type Contactor Voltage AC J7K -BM 20V 0Hz / 240V 60Hz J7K -BM -01 J7K - BM V 0Hz / 120V 60Hz J7K - B M V 0Hz / 480V 60Hz J7K -BMA 110V 0 / 60Hz J7K -BMA -01 J7K - BMA V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - B M - D 24V DC J7K -BM -01 -D J7K - B M D 48V DC J7K -BM -4 -D J7K -BMA -D 60V DC J7K-BMA-01-D J7K-BMA-10-D 220V DC J7K -CM(A) Type Contactor Voltage AC J7K -CM 20V 0Hz / 240V 60Hz J7K -CMA 110V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - C M - D 24V DC J7K -CMA -D 48V DC 60V DC 220V DC J7K -DM(A) Type Contactor Voltage AC J7K -DM 20V 0Hz / 240V 60Hz J7K -DMA 110V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - D M - D 24V DC J7K -DMA -D 48V DC 60V DC 220V DC J7K -EM(A) Type Contactor Voltage AC J7K -EM 20V 0Hz / 240V 60Hz J7K -EMA 110V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - EM - D 24V DC J7K -EMA -D 48V DC 60V DC 220V DC J7K -FM(A) Type Contactor Voltage AC J7K -FM 20V 0Hz / 240V 60Hz J7K -FMA 110V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - FM - D 24V DC J7K -FMA -D 48V DC 60V DC 220V DC J7K -GM(A) Type Contactor Voltage AC J7K -GM 20V 0Hz / 240V 60Hz J7K -GMA 110V 0Hz / 120V 60Hz 41V 0Hz / 480V 60Hz 110V 0 / 60Hz 20V 0 / 60Hz 48V 0Hz 24V 0Hz DC J7K - G M - D 24V DC J7K -GMA -D 48V DC 60V DC 220V DC

5 System overview Contactor J7K -AMA -10( -D) J7K -AMA -01( -D) J7K-AMA-4(-D) J7K -BM(A)( -D) J7K -BM(A) -10( -D) J7K -BM(A) -01( -D) J7K - B M - 4( - D ) J7K -CM(A)( -D) Auxiliary contact modules Top mounting 2 -pole J7K - AM - 11 J7K -A -02 J7K -A pole J7K -AM -22 J7K -A -04 J7K -A -40 Top mounting 2 -pole J7K - BM - 11 J7K -B -02 J7K -B pole J7K -BM -22 J7K -BM -1 J7K -B -04 J7K - B - 1 J7K -B -40 Overload relays for direct mounting - - Base for separate mounting J7TK -B J7TKB -B Pneumatic timer module J7KB -PTE -11 J7KB -PTD -11 J7K -DM(A)( -D) Side mounting J7K - CM - 11S Except for J7K-BM(A)(-D) and J7K-BM-4(-D) J7TK -D J7TKD -B J7K -EM(A)( -D) J7K -FM(A)( -D) Side mounting 2 -pole J7K -FM -02 SA J7K -FM -02 SI J7K - FM - 11 SA J7K - FM - 11 SID J7K - FM - 11 SI J7K -FM -20 SA J7K -FM -20 SI J7TK -F -.../FP direct mounting J7TK -F -.../FB separate mounting - J7K -GM(A)( -D) J7TK -F -.../GP direct mounting - J7TK -F -.../GB separate mounting 4

6 Rating overview J7K- AMA- 10(- D) AMA- 01(- D) AMA- 4(- D) BM(- D) BM- 10(- D) BM- 01(- D) BM- 4(- D) BMA(- D) BMA- 10(- D) BMA- 01(- D) CM(- D) CMA(- D) DM(- D) DMA(- D) Rated operational voltage kw kw kw kw kw kw kw AC -, three -phase motor rating 0-60 Hz V V V /690 V V AC -4, three -phase motor rating 0-60 Hz V V V /690 V V AC -1, resistive rating V V V /690 V V * A A A A A A A Max. 690 V V J7K- EM(- D) EMA(- D) FM(- D) FMA(- D) GM(- D) GMA(- D) Rated operational voltage kw kw kw kw kw kw AC -, three -phase motor rating 0-60 Hz V V V /690 V V AC -4, three -phase motor rating 0-60 Hz V V V /690 V V AC -1, resistive rating V V V /690 V V * A A A A A A Max. 690 V V * Conventional free air thermal current I th =I e, open.

7 Contactor with interlocked opposing contacts Coil AC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V 240 V 440 V open kw kw kw kw kw kw kw kw Basic units, -pole Voltage tolerance of the coil 0.80 to 1.1 x U c Contacts to EN 0012 Terminal markings Coil to EN 000 Std. J7K -AMA A J7K -AMA A 1 10* * Basic units, 4 -pole Voltage tolerance of the coil 0.80 to 1.1 x U c Contacts to EN 0012 J7K -AMA -4-20A 7 A Auxiliary contact modules** Contacts to EN 0012 should be given preference + + J7K -AM -11 M = Make contact B = Break contact 2 -pole 1M 1B J7K -AM pole 2M 2B =21* =(11) * =2* =(22)* - - Auxiliary contact modules** Contacts to EN J7K -A -02 M = Make contact B = Break contact 2 -pole - 2B =12* =(02)* 1 61 = 0* 2 62 J7K -A -11 1M 1B J7K -A -20 2M =21* =(11) * =0* =(20)* 4 64 = 12* = 21* J7K -A pole - 4B J7K -A -22 2M 2B =14* =(04)* =2* =(22)* = 0* = 2* J7K -A -40 4M =0* =(40)* = 41* * jj Distinctive number (The numbers in brackets apply to J7K -AMA -4) ** Auxiliary contact modules, conventional free air thermal current I th =10A. 6

8 Coil DC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V 240 V 440 V open kw kw kw kw kw kw kw kw Terminal markings Coil to EN 000 Std. Basic units, coil rating 2.6 W, -pole Voltage tolerance of the coil x Uc. Integral resistor/diode combination. Contacts to EN 0012 J7K-AMA-10-D A + - A1 A * + J7K-AMA-01-D A A1 - A * Basic units, 4 -pole Voltage tolerance of the coil x Uc. Integral resistor/diode combination. Contacts to EN 0012 J7K - A MA D - 20A + A A Auxiliary contact modules** + + Contacts to EN 0012 J7K -AM -11 M = Make contact B = Break contact 2 -pole 1M 1B =21* =(11)* - J7K -AM pole 2M 2B =2* =(22)* - Auxiliary contact modules** + + Contacts to EN 000 J7K -A -02 M = Make contact B = Break contact 2 -pole - 2B =12* =(02)* 1 61 = 0* 2 62 J7K -A -11 1M 1B =21* =(11)* 4 62 = 12* J7K -A -20 2M =0* =(20)* 4 64 = 21* J7K -A pole - 4B J7K -A -22 2M 2B =14* =(04)* =2* =(22)* = 0* = 2* J7K -A -40 4M =0* =(40)* = 41* * jj Distinctive numbers (The number in brackets apply to J7K -AMA -4 -D) ** Auxiliary contact modules, conventional free air thermal current I th =10A. 7

9 Contactor Coil AC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V * 240 V 440 V * open kw kw kw kw kw kw kw kw Basic units, -pole Terminal markings Coil to EN 000 Std. J7K -BM A 1 A J7K -BMA A 1 A J7K -CM A 1 A J7K -CMA A 1 A Basic units, 4 -pole J7K - BM A 7 1 A Auxiliary contact module, side mounting** + + Can be combined with auxiliary contacts for top mounting up to a maximum of four contacts. J7K-CM-11S M = Make contact B = Break contact 2 -pole 1M 1B Auxiliary contact modules, top mounting + + J7K -BM -11 J7K -BM -22 J7K -BM -1 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN 0012 and is to be given preference. 2 -pole 1M 1B 4 -pole 2M 2B M 1B J7K -B -02 J7K -B -20 J7K -B -04 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN pole - 2B 2M - 4 -pole - 4B J7K -B -1 1M B J7K -B -40 4M * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. 8

10 Coil DC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V * 240 V 440 V * open kw kw kw kw kw kw kw kw Basic units, -pole Terminal markings Coil to EN 000 Std. J7K - BM - D A 1 J7K -BMA -D A 1 J7K - CM - D A 1 J7K -CMA -D A 1 Basic units, 4 -pole J7K - B M D - 20A Auxiliary contact module, side mounting** + + Can be combined with auxiliary contacts for top mounting up to a maximum of four contacts. J7K-CM-11S M = Make contact B = Break contact 2 -pole 1M 1B Auxiliary contact modules, top mounting + + J7K -BM -11 J7K -BM -22 J7K -BM -1 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN 0012 and is to be given preference. 2 -pole 1M 1B 4 -pole 2M 2B M 1B J7K -B -02 J7K -B -20 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN pole - 2B 2M - J7K -B pole - 4B J7K -B -1 1M B J7K -B -40 4M * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. 9

11 Contactor Coil AC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V * 240 V 440 V * open kw kw kw kw kw kw kw kw Basic units, -pole Terminal markings Coil to EN 000 Std. J7K -DM A 1 J7K -DMA A 1 J7K -EM A 1 J7K -EMA A 1 Auxiliary contact module, side mounting** + + Can be combined with auxiliary contacts for top mounting up to a maximum of four contacts. J7K-CM-11S M = Make contact B = Break contact 2 -pole 1M 1B Auxiliary contact modules, top mounting + + J7K -BM -11 J7K -BM -22 J7K -BM -1 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN 0012 and is to be given preference. 2 -pole 1M 1B 4 -pole 2M 2B M 1B J7K -B -02 J7K -B -20 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN pole - 2B 2M - J7K -B pole - 4B J7K -B -1 1M B J7K -B -40 4M * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. 10

12 Coil DC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC- 4 current 220 V 80 V 00 V 660 V 220 V 80 V 00 V 660 V I 20 V 400 V 690 V 20 V 400 V 690 V th =I e AC V 440 V * 240 V 440 V * open kw kw kw kw kw kw kw kw Terminal markings Coil to EN 000 Terminal markings Coil to EN 000 Std. Basic units, -pole J7K - DM - D A 1 J7K -DMA -D A 1 J7K - EM - D A 1 J7K -EMA -D A 1 Auxiliary contact module, side mounting** + + Can be combined with auxiliary contacts for top mounting up to a maximum of four contacts. J7K-CM-11S M = Make contact B = Break contact 2 -pole 1M 1B Auxiliary contact modules, top mounting** + + J7K -BM -11 J7K -BM -22 J7K -BM -1 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN 0012 and is to be given preference. 2 -pole 1M 1B 4 -pole 2M 2B M 1B J7K -B -02 J7K -B -20 M = Make contact B = Break contact The combination of basic unit and auxiliary contact module correspond to EN pole - 2B 2M - J7K -B pole - 4B J7K -B -1 1M B J7K -B -40 4M * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. 11

13 Contactor Coil AC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC-4 current 220V 80V 00V 660V 1000V 220V 80V 00V 660V 1000V I 20V 400V 690V * 20V 400V 690V * th =I e AC V 440V * 240V 440V * open kw kw kw kw kw kw kw kw kw kw Terminal markings Coil to EN 000 Basic units Snap fitting onto 7 mm top -hat rail to EN 002. J7K- FM A J7K- FMA A J7K- GM A J7K- GMA A Auxiliary contact modules, side mounting** (1)*** (2)*** ()*** J7K- FM- 20SI M = Make contact B = Break contact 2 -pole 2M J7K- FM- 11SI 1M 1B J7K- FM- 02SI - 2B J7K- FM- 11SID 1M 1B early make late break J7K- FM- 20SA M = Make contact B = Break contact 2 -pole 2M J7K- FM- 11SA 1M 1B J7K- FM- 02SA - 2B * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. *** See layout Note (1), (2) and () of auxiliary contact modules on page

14 Coil DC operated Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal AC- AC-4 current 220V 80V 00V 660V 1000V 220V 80V 00V 660V 1000V I 20V 400V 690V * 20V 400V 690V * th =I e AC V 440V * 240V 440V * open kw kw kw kw kw kw kw kw kw kw Terminal markings Coil to EN 000 Basic units Snap fitting onto 7 mm top -hat rail to EN 002. Units with integral suppressor circuit (varistor). J7K- FM- D A J7K-FMA-D A J7K- GM- D A J7K-GMA-D A Auxiliary contact modules, side mounting** (1)*** (2)*** ()*** J7K- FM- 20SI M = Make contact B = Break contact 2 -pole 2M J7K- FM- 11SI 1M 1B J7K- FM- 02SI - 2B J7K- FM- 11SID 1M 1B early make late break J7K- FM- 20SA M = Make contact B = Break contact 2 -pole 2M J7K- FM- 11SA 1M 1B J7K- FM- 02SA - 2B * Do not reverse directly. ** Auxiliary contact modules, conventional free air thermal current I th =16A. *** See layout Note (1), (2) and () of auxiliary contact modules on page 16. 1

15 Contactor, complete units Article No. Article No. Max. three-phase motor rating 0-60 Hz Conv. thermal Coil AC operated Coil DC operated AC- AC-4 current 220V 80V 00V 660V 220V 80V 00V 660V I 20V 400V 690V 20V 400V 690V th =I e AC V 440V * 240V 440V * open kw kw kw kw kw kw kw kw Complete units Terminal markings Coil to EN 000 Std. J7K- BM- 10 (20V 0Hz) J7K- BM- 10- D (24 VDC) A 1 14 AC= DC=1 J7K- BM- 01 (20V 0Hz) J7K- BM- 01- D (24 VDC) A AC= DC=1 J7K-BMA-10 (20V 0Hz) J7K-BMA-10-D (24 VDC) A 1 14 AC= DC=1 J7K-BMA-01 (20V 0Hz) J7K-BMA-01-D (24 VDC) A AC= DC=1 * Do not reverse directly. Accessories RC Suppressor Article No. Voltage For use with contactor Note Std. J7KA -RC20 A1 A V AC J7K -AMA For AC operated 0-60 Hz contactor. Note the drop -out time. 1 RC Suppressors Article No. Voltage For use with contactor Note Std. J7KB -RC20 A V AC J7K -BM to J7K -EMA For AC operated 0-60 Hz contactor. 10 Note the drop -out time. J7KF -RC20 A2 J7K -FM to J7K -GMA 10 Varistor suppressor Article No. Voltage For use with contactor Note Std. J7KA -VG20 A1 A V AC J7K-AMA(-D) For AC operated, 0-60 Hz. (J7K -AMA -D) DC operated contactors fitted with integral suppressor circuit as standard 10 Free -wheel diode suppressor Article No. Voltage For use with contactor Note Std. J7KB -FD A1 A V DC J7K -BM to J7K -EMA For DC operated contactors. Note drop out time

16 Varistor suppressors Article No. Voltage For use with contactor Note Std. J7KB -VG20 J7KB -VG41 A1 A V AC/DC 80-41V AC/DC J7K -BM to J7K -EMA J7K -FM to J7K -GMA For AC operated 0-60 Hz contactors (J7K -BM to J7K -GM(A)) and DC operated contactors (J7K - BM( - D) to J7K - GMA( - D). DC operated contactors fitted with integral suppressor circuit (varistor) as standard Mechanical interlocks Article No. For use with contactor Note Std. J7KA -MV J7K -AMA For contactors with the same or different magnet systems, mounted vertically or horizontally. Distance between contactors: 0 mm. Mechanical lifespan: 2. x 10 6 operations. Additional auxiliary contact modules can be fitted. J7KB -MV J7K -BM to J7K -EMA For contactors with the same or different frame size but with the same magnet system, mounted vertically or horizontally. Distance between contactors: 1 mm. Mechanical lifespan: x 10 6 operations. J7KF -MV* J7K -FM to J7K -GMA For contactors with the same or different magnet systems, mounted vertically or horizontally. Distance between contactors: 0 mm. Mechanical lifespan: x 10 6 operations. Auxiliary contact modules cannot be placed between the mechanical interlock and the contactor. 1 * See layout Note 4 of auxiliary contact modules on page 16. Pneumatic timer modules Article No. For use with contactor Note Terminal ratings Std. J7KB -PTE -11 ON -delayed J7KB -PTD -11 OFF -delayed J7K -BM to J7K -EMA Switching time ranges of s and s adjustable. Conventional free -air thermal current 10 A. ON -delayed OFF -delayed th -pole, only for AC -1 load Article No. For use with contactor I e AC -1, open Terminal rating Std. J7KC -N J7K -CM A J7KD -N J7K -DM A J7KE -N J7K -EM 7 A J7KF -N J7K -FM 100 A (No UL/CSA approbiation!)

17 Individual coil Article No. For use with contactor AC -voltage DC -voltage Std. J7KB -IC(...) J7K -BM(A) 24V 0Hz - 1 J7KC -IC(...) J7K -CM(A) 48V 0Hz 110V 0/60Hz 1 J7KD -IC(...) J7K -DM(A) 20V 0/60Hz 1 J7KE -IC(...) J7K -EM(A) 41V 0/60Hz 1 J7KF -IC(...) J7K -FM(A) 1 J7KG -IC(...) J7K -GM(A) 1 J7KB -IC(...) J7K -BR 1 J7KB -IC -D(...) J7K -BM(A) -D - 24 VDC 1 J7KC -IC -D(...) J7K -CM(A) -D 48 VDC 60 VDC 1 J7KD -IC -D(...) J7K -DM(A) -D 110 VDC 1 J7KE -IC -D(...) J7K -EM(A) -D 220 VDC 1 J7KF -IC -D(...) J7K -FM(A) -D 1 J7KG -IC -D(...) J7K -GM(A) -D 1 J7KB -IC -D(...) J7KM -BR -D 1 Layout of auxiliary contact modules (1) J 7K - FM - J 7K - FM -..SI(D)..SI(D) (4) J7K-FM(A)(-D) J7K-GM(A)(-D) J7K-FM(A)(-D) J7K-GM(A)(-D) J7K -MV J7K-FM(A)(-D) J7K-GM(A)(-D) (2) J 7K - FM - J 7K - FM -..SI(D)..SI(D) 4. Auxiliary contact modules can not be fitted between mechanical interlock and contactor J 7K - FM -..SA J7K-FM(A)(-D) J7K-GM(A)(-D) J 7K - FM -..SA () J 7K - FM -..SA J 7K - FM -..SA + + J7K-FM(A)(-D) J7K-GM(A)(-D) 1. Up to 8 contacts possible. 2. If there are more than 4 contacts in total, up to 4 make contacts or 4 break contacts are permitted.. Any combination is permissible with total of 4 contacts or less. 16

18 Contact travel diagrams for contactor The diagrams show the closing and opening travel of the auxiliary contact modules of contactors and modules at no -load. Tolerances are not taken into consideration. J7K -AMA -.. (AC) J7K -GM(A) Make contact mm Make contact mm Break contact mm J7K -FM(A) J7K -FM -..S. J7K -AMA -.. -D (DC) Make contact mm Make contact mm Break contact mm Break contact mm J7K -GM(A) J7K -FM -..S. J7K -A -.. Make contact mm Make contact mm Break contact mm Break contact mm J7K -FM(A) J7K -FM -..SID J7K -BM(A) -..; J7K -BM(A) J7K -B(M) -.. Make contact mm Make contact mm Break contact mm Break contact mm J7K -GM(A) J7K -FM -..SID J7K -CM(A); J7K -CM(A) + J7K -B(M) -.. Make contact mm Make contact mm Break contact mm Break contact mm J7K -DM(A); J7K -DM(A) + J7K -B(M) -.. Make contact Break contact mm mm J7K -EM(A); J7K -EM(A) + J7K -B(M) -.. Make contact Break contact mm mm J7K -FM(A) Make contact mm 17

19 Overload relays with single -phasing sensitivity to IEC Direct mounting Overload relay For use with Terminal marking Auxiliary contact module*** J7TK -B -0,4 J7TK -B -0,6 J7K -BM(A)( -D) J7K -CM(A)( -D) 97 9 J7TK -B -1, Setting range overload release** I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL 1M 1B A A A 2 4 J7TK -B -1, A 2 6 J7TK -B -2, A 2 10 J7TK -B A 2 16 J7TK -B A 2 20 J7TK -B A 0 2 J7TK -B A 6 J7TK -B A 6 0 Std. Overload relay For use with Terminal marking Auxiliary contact module*** J7TK -D -10 J7TK -D -16 J7TK -D -24 J7K -DM(A)( -D) J7K -EM(A)( -D) Setting range overload release** I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL M 1B A A A J7TK -D A J7TK -D A J7TK -D A Std. Overload relay For use with Terminal marking Auxiliary contact module*** Setting range overload release** I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL Max. A I Std. J7TK -F -/FP J7K -FM(A)( -D) M 1B A J7TK -F -0/FP J7TK -F -70/FP A A J7TK -F -100/FP A Overload relay For use with Terminal marking Auxiliary contact module*** Setting range overload release** I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL Max. A I Std. J7TK -F -100/GP J7K -GM(A)( -D) M 1B A J7TK -F -12/GP A J7TK -F -10/GP A * The max. permissible fuse of the contactor must be observed when mounting overload relays directly. ** Tripping class 10 A. *** M = make contact, B = Break contact 18

20 Separate mounting Overload relay Terminal marking Auxiliary contact module*** Setting range overload release** I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL Max. A I Std. J7TK -D M 1B A Overload relay Terminal marking Auxiliary contact module*** Setting range** overload release I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL Max. A I Std. J7TK -F -/FB M 1B A J7TK -F -0/FB J7TK -F -70/FB A A J7TK -F -100/FB A Overload relay Terminal marking Auxiliary contact module*** Setting range** overload release I r 1 max. AgL Short -circuit protection* Type of coordination 2 max. AgL Max. A I Std. J7TK -F -100/GB M 1B A J7TK -F -12/GB J7TK -F -10/GB A A * The max. permissible fuse of the contactor must be observed when mounting overload relays directly. ** Tripping class 10 A. *** M = make contact, B = Break contact Bases for separate mounting For use with Application note Std. J7TKB -B J7TK -B Snap fitting on top -hat rail to EN x1 or screw fixing. J7TKD -B J7TK -D 19

21 Tripping characteristics These tripping characteristics show mean values of the tolerance range at an ambient temperature of 20 C, starting from cold. They show the tripping time in relation to the response current; at operational temperature, the tripping time of the overload relay drops to approx. 1/4 of that shown. Specific characteristics for each individual setting range are available on request. Protection of DC motors 1 -pole 2 -pole J7TK -B J7TK -D J7TK -F Features J7TK -B J7TK -F J7TK -D Single -phasing sensitivity X X Temperature compensation X X Auxiliary contacts 1M+1B X X Test -/OFF button X X Hand/Auto reset button X X Separate mounting X X Trip -free release X X Trip indication X X 20

22 Engineering Data Normal switching duty (AC -) AC -/400V Rated output of three -phase motors 0-60 Hz kw Rated operational current 0-60 Hz A GMA(--D) GM(--D) FMA(--D) FM(--D) EMA(--D) EM(--D) DMA(--D) DM(--D) CMA(--D) CM(--D) BMA(--D) BM(--D) AMA AMA--D AMA Squirrel -cage motors Operating characteristics: Starting from rest Stopping after attaining full running speed Electrical characteristics: Make up to 6 x rated motor current Break 1 x rated motor current Utilization category: 100% AC - Typical applications: Compressors, Pumps, Fans, Valves Lifts, Escalators, Conveyors, Bucket elevators Mixers, Agitators, Centrifuges, Air -conditioning systems. Drives in general in manufacturing and processing machines AMA(--D) J7K Contactors Component lifespan (millions of operations) Extreme switching duty (AC -4) AC -4/400V Rated output of three -phase motors 0-60 Hz kw Rated operational current 0-60 Hz A GMA(--D) GM(--D) FMA(--D) FM(--D) EMA(--D) EM(--D) DMA(--D) DM(--D) CMA(--D) CM(--D) BMA(--D) BM(--D) AMA(--D) Squirrel -cage motors Operating characteristics: Inching, plugging, reversing Electrical characteristics: Make up to 6 x rated motor current Break up to 6 x rated motor current Utilization category: 100% AC -4 Typical applications: Printing presses Wire -drawing machines Centrifuges Special drives for manufacturing and processing machines J7K Contactors Component lifespan (millions of operations) 21

23 Switching duty for non -motor loads, -pole (AC -1) AC -1/400V Breaking current A GMA GM FM(A) EMA EM DMA DM CMA CM BMA BM AMA Operating characteristics: Non -inductive or slightly inductive loads Electrical characteristics: Make up to 1. x rated motor current Break 1 x rated motor current Utilization category: 100% AC -1 Typical applications: Electric heater J7K Contactors Component lifespan (millions of operations) Max, conventional thermal current I th for enclosed type 22

24 Short -time loading Pause between two loads: 1 min AC -1/400V A Short -time current EM(A) DM(A) CM(A) BM(A) AMA 20 1 J7K Contactors sec Duration of load 1min min min 10min 1min AC -1/400V A Short -time current GM(A) FM(A) J7K Contactors sec Duration of load 1min min min 10min 1min 2

25 Determination of the max. number of operations per hour in relation to rating and utilization category (Approx. value) Ops./h = Max. number of operations per hour. Ops./h Type Characteristics AC -1 AC - AC -2 AC -4 J7K-AMA(-D) J7K -BM( -D) J7K-BMA(-D) J7K -CM( -D) J7K-CMA(-D) J7K -DM( -D) J7K-DMA(-D) J7K -EM( -D) J7K-EMA(-D) J7K -FM( -D) 8 J7K-FMA(-D) 6 8 J7K -GM( -D) J7K-GMA(-D) % P N (kw) Ops./h % P N (kw) 24

26 Specifications Contactors General Typ J7K -AMA J7K -AMA -D Standards IEC 947, EN 60947, UL, CSA Mechanical lifespan 10 x 10 6 Ops. 20 x 10 6 Ops. Max. operating frequency Mechanical 9000 Ops./h Climatic proofing Damp heat, constant, to IEC 68 Part 2 - Ambient temperature Open min./max. -2/+0 C Mounting position Damp heat, cyclic, to IEC 68 Part 2-0 As required, except vertical with A1/A2 at bottom Mechanical shock resistance (sinusoidal shock 10 ms) Basic unit Main contacts Make contacts 10 g Auxiliary Make/break 10/8 g contacts contacts Basic unit with auxiliary Main contacts Make contacts 10 g contact module Auxiliary contacts Make/break contacts 10/8 g Degree of protection IP20 Protection against direct contact from front when actuated by Finger - and back -of -hand proof a perpenticular test finger (IEC6) Weights 0.17 kg 0.2 kg Terminal capacity Solid (min.) 2 x 0.7 mm 2 Auxiliary and main contacts Solid (max.) 2x2.mm 2 Flexible with ferrule to DIN x1.mm 2 (max.) Solid or stranded (min.) 18 AWG Solid or stranded (max.) 14 AWG Terminal screw M. Pozidriv screwdriver Size 2 Standard screwdriver 0.8 x. mm 1x6mm Tightening torque (max.) 1.2 N A1 A2 Main contacts Typ J7K -AMA J7K -AMA -D Rated impulse withstand voltage U imp 6000 V Overvoltage category/pollution degree III/ Rated insulation voltage U i 690 V AC Rated operational voltage U e 690 V AC Safe isolation to IEC6 between coil and contacts and 00 V AC between contacts Making capacity cos φ to IEC A 110 A Breaking capacity cos φ to IEC /20 V 90 A 80/400 V 90 A 00 V 64 A 660/690 V 4 A Short -circuit rating max fuse Type 2 10 A gl coordination Type 1 coordination 20 A gl 2

27 AC Typ J7K -AMA( -4) J7K -AMA -D AC -1 duty (conventional free air thermal current I th rated operational current I e 0-60 Hz -pole Open at 40 C 22 A 1 -pole Three/four main contacts in parallel AC - duty (rated operational current I e Open* Open at 0 C 20 A Open at C 19 A Open* 0 A (60 A for J7K -AMA -4) 0-60 Hz 220/20 V 8.8 A AC -4 duty (rated operational current I e Open* 80/400 V 8.8 A 00 V 6.4 A 660/690 V 4.8 A 0-60 Hz 220/20 V 6.6 A DC (rated operational current I e, Open** 80/400 V 6.6 A 00 V A 660/690 V.4 A Typ J7K -AMA J7K -AMA -4 J7K -AMA -D DC -1 duty 12 V 20 A - 20 A 24 V 20 A - 20 A 60 V 20 A - 20 A 110 V 20 A - 20 A 220 V 20 A - 20 A DC - duty 12 V 8A - 8A 24 V 8A - 8A 60 V 4A - 4A 110 V A - A 220 V - 1A - DC - duty 12 V 2. A - 2. A Current heat loss ( - or 4 -pole) 24 V 2. A - 2. A 60 V 2. A - 2. A 110 V 1. A 2. A 1. A 220 V 0. A 1A 0. A at conventional 2W 2.7 W. W free air thermal current I th at I e to 0. W W AC -/400 V * At maximum permissible ambient temperature ** For switching DC configuration see Appendix, page NO TAG. 26

28 Magnet system Typ J7K -AMA J7K -AMA -D Pick -up and drop -out values AC operated, single voltage coil 0 Hz and dual -voltage coil 0 Hz, 60 Hz Pick -up x U c - AC operated, Dual -frequency coil...v 0/60 Hz Pick -up x U c - DC operated Pick -up x U c Power AC operated, single voltage Pick -up 2 VA/22 W - consumption of coil 0 Hz and dual -voltage the coil coil 0 Hz, 60 Hz Sealing 4.6 VA/1. W - AC operated, Pick -up 0 VA/26 W - dual -frequency coil...v 0/60 Hz at 0 Hz Sealing.4 VA/1.6 W - AC operated, Pick -up 29 VA/24 W - dual -frequency coil...v 0/60 Hz at 60 Hz Sealing.9 VA/1.1 W - DC operated Pick -up = W Sealing Duty factor 100 % DF Switching times Make contacts Closing ms 26 - ms at 100 % U c delay (Approximate Opening values) delay 8-18ms 1-2 ms With top mounting auxiliary contacts Closing delay max. 4 ms max. 70 ms Reversing Changeover time at 110 % U c ms 40-0 ms contactors Arcing time at 690 V AC 12 ms Coil 0/60 Hz Mechanical lifespan at 0 Hz approximately 0% less than listed under General 27

29 Contacts Typ J7K -AMA J7K -AMA -D Interlocked opposing contacts to German specification ZH + 1/47, including auxiliary contact modules Rated impulse withstand voltage U imp 6000 V Overvoltage category/pollution degree III/ Rated insulation voltage U i 690 V AC Rated operational voltage U e 600 V AC Safe isolation to IEC6 between coil and auxiliary contacts, 00 V AC and between auxiliary contacts Rated operational current Ie AC /240 V 6A 80/41 V A 00 V 1. A Top mounting auxiliary contacts 4A Rated operational current I e at DC -1* (Above 110 V and at L/R > 1 ms it is essential that means of arc suppression be used in parallel with the contacts): required capacitor 1 µf und resistor 0. Ω in series; L/R 1 ms, e.g. contactor coils, solenoid valves, DC motors: 1 contact in series at 24 V 2. A 2 contacts in series at 60 V 2. A contacts in series at 110 V 1. A contacts in series at 220 V 0. A Conventional free air thermal current I th Control circuit reliability U e = 24 V DC, 17 V,.4 ma Component lifespan (U e = 240 V) AC -1 DC -1* At Ie = 0. A, L/R= 0 ms, 2 contacts in series Maximum overcurrent protective device 10 A Error rate H F <10-8, < 1 fault in 100 million operations 0.2 x 10 6 Operations 0.1 x 10 6 Operations Short -circuit rating with direct connection to 220/240 V J7M-AM-4 mains or transformer > 1000 VA without welding 80/41 V J7M-AM-4 Without welding 00 V 6AgL Maximum fuse 00 V 10 A fast Current heat loss at conventional free air thermal current I th max. 0.2 W per contact * Making and breaking currents to DC -1, time constant as stated max. 0. W 28

30 General Typ J7K- BM J7K- BMA J7K- CM J7K- CMA J7K- DM J7K- DMA Standards Mechanical lifespan AC operated 10 x 10 6 Ops. Max. operating frequency Mechanical DC operated IEC 947, EN 60947, UL, CSA 10 x 10 6 Ops. AC operated (Ops./h) DC operated (Ops./h) Climatic proofing Damp heat, constant, to IEC 68 Part 2 - Ambient temperature Open min./max. -2/+0 C Mounting position Damp heat, cyclic, to IEC 68 Part 2-0 For DC operation, observe minimum spacing mm AC/DC operation J7K -BM to J7K -EMA AC operation J7K -BM to J7K -EMA DC operation J7K -BM to J7K -EMA Mechanical shock resistance (sinusoidal 20 ms) Main contacts Auxiliary contacts Make contacts (AC) Make contacts (AC) Break contacts (AC) 10 g 10 g 8g 10 g 10 g 8g 6g Degree of protection IP20 IP00 Protection against direct contact from the front by a Finger - and back -of -hand proof perpenticular test finger (IEC6) Weights Basic unit AC operated 0.2 kg 0.42 kg 0.71 kg DC operated 0.0 kg 0.77 kg 1.2 kg Terminal capacities Solid* 1x(0.7-4)mm 2 1x(1-6)mm 2 1 x (2. -10) mm 2 main cables: Screw terminal; one or 2x(0.7-4)mm 2 2x(1-6)mm 2 2 x (2. -10) mm 2 two conductors can be Flexible with ferrule to DIN x(0.7-4)mm 2 1x(1-6)mm 2 1 x (2. -16) mm 2 connected (max.)* 2x(0.7-4)mm 2 2x(1-6)mm 2 2 x (2. -10) mm 2 Stranded x (10-2) mm x10mm 2 Solid or min. AWG 18 AWG 16 AWG 12 stranded d max. AWG 10 AWG 4 Terminal capacities Solid 1x(0.7-4)mm 2 control circuit i cable: Screw terminal; one or 2x(0.7-4)mm 2 two conductors can be Flexible with ferrule 1 x (0.7-2.) mm 2 connected 2 x (0.7-2.) mm 2 Solid or min. AWG 18 stranded d max. AWG 12 Terminal screw Main cable M. M4 M6 Control circuit cable M. Main cable and control Pozidriv screwdriver Size 2 circuit i cable Standard screwdriver 0.8 x. mm 1x6mm Tightening g torque Main cable 1.2 Nm 1.8 Nm 4Nm Control circuit cable 1.2 Nm * When using two conductors, maximum permissible difference in cross -section: one size. 29

31 General Typ J7K- EM J7K- EMA J7K- FM J7K- FMA J7K- GM J7K- GMA Standards Mechanical lifespan AC operated 10 x 10 6 Ops. Max. operating frequency Mechanical IEC 947, EN 60947, UL, CSA DC operated 10 x 10 6 Ops. x10 6 Ops. AC operated (Ops./h) 000 DC operated (Ops./h) Climatic proofing constant Damp heat, to IEC 68 Part 2 - cyclic Damp heat, to IEC 68 Part 2-0 Ambient temperature Open min./max. -2/+0 C -2/+ C Mounting position For DC operation, observe minimum spacing mm Mechanical shock resistance (sinusoidal) Main contacts Auxiliary contacts Make contacts (AC) Make contacts (AC) Break contacts (AC) 8g(20ms) 8g(20ms) 6g(20ms) AC/DC operation J7K -EM to J7K -GMA 10g(10ms) 10g(10ms) 8g(10ms) AC operation J7K -EM(A) AC/DC operation J7K -FM to J7K -GMA DC operation J7K -EM(A) Degree of protection IP00 Protection against direct contact from the front by a Finger - and back -of -hand proof perpenticular test finger (IEC6) Weights Basic unit AC operated 0.9 kg 2kg 2.9 kg DC operated 1.8 kg 2kg 2.9 kg Terminal capacity Solid* 1 x (2. -16) mm 2 1 x (6-16) mm 2 main cables: Screw terminal; one or 2 x (2. -16) mm 2 2 x (6-16) mm 2 two conductors can be Flexible with ferrule* 1 x (2. -2) mm 2 1 x (4-0) mm 2 1 x (16-70) mm 2 connected 2 x (2. -10) mm 2 2 x (4-0) mm 2 2 x (16-70) mm 2 Terminal capacity control circuit i cable: Screw terminal; one or two conductors can be connected Stranded 1 x (10 -) mm 2 16 mm 2 2x10mm 2 0 mm 2 70 mm 2 Solid or min. AWG 12 AWG 10 AWG 6 stranded d max. AWG 2 AWG 2/0 Solid 1x(0.7-4)mm 2-2x(0.7-4)mm 2 Flexible with ferrule 1 x (0.7-2.) mm 2-2 x (0.7-2.) mm 2 Solid or min. AWG 18 - stranded d max. AWG 12 2 x AWG (18-12) Terminal screw Main cable M6 M 8 (SW4) Hexagon socket -head screw Control circuit cable M. Main cable and control Pozidriv screwdriver Size 2 circuit i cable Standard screwdriver 0.8 x. mm 1x6 Tightening g torque Main cable 4Nm 6Nm 10 Nm Control circuit cable 1.2 Nm * When using two conductors, maximum permissible difference in cross -section: one size. M 10 (SW) Hexagon socket -head screw 0

32 Main contacts Typ J7K- BM J7K- BMA J7K- CM J7K- CMA J7K- DM J7K- DMA Rated impulse withstand voltage U imp 8000 V Overvoltage category/pollution degree III/ Rated insulation voltage U i 690 V AC Rated operational voltage U e 690 V AC Safe isolation to IEC between coil and contacts 440 V AC 6 and between contacts 440 V AC Making capacity cos φ to IEC A 270 A 70 A Braking capacity cos φ to 220/20 V 10 A 20 A 80 A IEC /400 V 120 A 20 A 80 A 00 V 120 A 20 A A 660/690 V 100 A 210 A 2 A Short -circuit rating Type 2 coordination 20 A gl A gl 6 A gl Maximum fuse Type 1 coordination 2 A gl 0 A gl 100 A gl Typ J7K- EM J7K- EMA J7K- FM J7K- FMA J7K- GM J7K- GMA Rated impulse withstand voltage U imp 8000 V Overvoltage category/pollution degree III/ Rated insulation voltage U i 690 V AC 1000 V AC Rated operational voltage U e 690 V AC 1000 V AC Safe isolation to IEC between coil and contacts 440 V AC 00 V AC 6 and between contacts 440 V AC 00 V AC 690 V AC Making capacity cos φ to IEC A 100 A 1800 A Breaking capacity cos φ 220/20 V 70 A 1100 A 1800 A to IEC /400 V 600 A 1100 A 1800 A 00 V 600 A 1100 A 1800 A 660/690 V 4 A 60 A 1200 A 1000 V - 0 A 60 A Short -circuit rating Type 2 coordination 100 A gl 160 A gl 20 A gl Maximum fuse Type 1 coordination 12 A gl 20 A gl 1 A gl 1

33 AC Typ J7K- BM J7K- BMA J7K- CM J7K- CMA J7K- DM J7K- DMA AC -1 duty Conventional free air -pole, open at 40 C 22 A 8 A 60 A thermal current I th rated operational current at 0 C 20 A A A I e 0-60 Hz up to 690 V at C 19 A A 2 A AC - duty Rated operational current I e 0-60 Hz AC -4 duty Rated operational current I e 0-60 Hz 1 -pole, open* 0 A 8 A 140 A open* 220/20 V 8.8 A 12 A 1. A 22. A 0 A 8 A 80/400 V 8.8 A 12 A 1. A 22. A 0 A 6 A 00 V 9A 12 A 17 A 22. A 28 A 2 A 660/690 V 6.7 A 9A 1 A 17. A 21 A 2 A open* 220/20 V 6.6 A 8.7 A 11. A 1. A 22. A 0 A 80/400 V 6. A 8. A 11. A 1. A 22. A 0 A 00 V 6.4 A 9A 11. A 17 A 22. A 28 A 660/690 V 4.9 A 6.7 A 9A 1 A 17. A 21 A Typ J7K- EM J7K- EMA J7K- FM J7K- FMA J7K- GM J7K- GMA AC -1 duty Conventional free air -pole, open at 40 C 98. A 114 A 182 A thermal current I th rated operational current at 0 C 90 A 104 A 167 A I e 0-60 Hz up to 690 V at C 8 A 100 A 160 A AC - duty Rated operational current I e 0-60 Hz AC -4 duty Rated operational current I e 0-60 Hz * At max. permissible ambient temperature. 1 -pole, open* 22 A 20 A 400 A open* 220/20 V 0 A 62 A 7 A 8 A 104 A 147 A 80/400 V 4 A 8 A 72 A 8 A 104 A 142 A 00 V 4 A 4 A 64 A 78 A 106 A 127 A 660/690 V A 42 A 60 A 82 A 98 A 118 A 1000 V A A 40 A 47 A open* 220/20 V 7 A 49 A 64 A 7 A 86 A 106 A 80/400 V 6 A 4 A 8 A 72 A 8 A 106 A 00 V 2 A 4 A 4 A 64 A 78 A 106 A 660/690 V 2 A A 49 A 49 A 60 A 82 A 1000 V A A 40 A 40 A 2

34 DC Typ J7K- BM J7K- BMA J7K- CM J7K- CMA J7K- DM J7K- DMA DC -1 duty 60 V 20 A A A Rated operational current I e open 110 V 20 A A A 220 V 12 A 1 A 20 A 2 A 40 A 440 V A A 7A DC - duty 60 V 1 A 20 A 20 A 28 A 28 A Rated operational current I e open 110 V 1 A 20 A 20 A 28 A 28 A 220 V A 8A 10 A 12 A 1 A DC - duty 60 V 12 A 16 A 18 A 2 A 2 A 27 A Rated operational current I e open 110 V 12 A 16 A 18 A 2 A 2 A 27 A Current heat loss ( -pole) at conventional free air thermal 2. W.7 W 12.4 W current I th at I e AC -/400 V 0.4 W 0.8 W 0.7 W 1. W.8 W. W Typ J7K- EM J7K- EMA J7K- FM J7K- FMA J7K- GM J7K- GMA DC -1 duty 60 V 90 A 100 A 160 A Rated operational current I e open 110 V 90 A 100 A 160 A 220 V 80 A 100 A 160 A 440 V 10 A - - DC - duty 60 V 70 A 100 A 160 A Rated operational current I e open 110 V 70 A 91 A 14 A 220 V 4 A 91 A 14 A DC - duty 60 V 4 A 48 A 100 A 160 A Rated operational current I e open 110 V 4 A 48 A 91 A 14 A 220 V A 14 A Current heat loss ( -pole) at conventional free air thermal 20 W 21 W W current I th at I e AC -/400 V 4.6 W 8.4 W 11 W 1 W 1 W 28 W

35 Magnet system Typ J7K- BM J7K- BMA J7K- CM J7K- CMA J7K- DM J7K- DMA Pick -up and drop -out values AC operated Pick -up x U c ( x U c to 0/60 Hz coil) DC operated 1 ) Pick -up x U c Power consumption of AC operated Pick -up 67 VA 100 VA 16 VA the coil 2 W 72 W 88 W Single -voltage Sealing 8. VA 10 VA 14 VA coil...v 0 Hz 2. W W. W Dual -voltage Sealing 8.6 VA 10 VA 1 VA coil...v 0 Hz...V 60 Hz 2. W W 4W DC operated 1 ) Pick -up 9. W 10 W 14. W Sealing 9. W 10 W 14. W Duty factor 100 % DF Switching times at 100 % AC operated Closing delay ms 9-19 ms ms U c (approximate values); Main contacts Opening delay -14 ms -1 ms 6-1 ms DC operated 1 ) Closing delay -40 ms 40 - ms 68-7 ms Opening delay -10 ms 6-10 ms 10-1 ms Reversing contactors, AC operated, Changeover time at ms 2 ) 1-19 ms 2 ) ms 2 ) %U c Arcing time when AC operated 10 ms <20 ms Coil 0/60 Hz Mechanical lifespan at 0 Hz approximately 0 % less than listed under General Typ J7K- EM J7K- EMA J7K- FM J7K- FMA J7K- GM J7K- GMA Pick -up and drop -out values AC operated Pick -up x U c ( x U c to 0/60 Hz coil) DC operated 1 ) Pick -up x U c Power consumption of AC operated Pick -up 18 VA 20 VA 0 VA the coil 106 W 10 W 220 W Single -voltage Sealing 16 VA 24 VA 8 VA coil...v 0 Hz 4. W. W 10 W Dual -voltage Sealing 16. VA 26 VA 40 VA coil...v 0 Hz...V 60 Hz.8 W 7W 10 W DC operated 1 ) Pick -up 16 W 20 W 1 ) 60 W 1 ) Sealing 16 W W 1 ).7 W 1 ) Duty factor 100 % DF Switching times at 100 % AC operated Closing delay ms ms ms U c (approximate values); Main contacts Opening delay -1 ms 8-1 ms 7-11 ms DC operated 1 ) Closing delay 7-90 ms ms 28-0 ms Opening delay ms 12-2 ms 1-16 ms Reversing contactors, AC operated, Changeover time at ms 2 ) 21-0 ms 2-0 ms ) %U c Arcing time when AC operated <20 ms ms 10-2 ms Coil 0/60 Hz Mechanical lifespan at 0 Hz approximately 0 % less than listed under General 1 ) Smoothed DC voltage of three -phase bridge rectifier. 2 ) J7K -BM(A) to J7K -EM(A) must have a current -free pause of at least 2 ms for reversing at 660/690 V. ) J7K -GM(A) must have a current -free pause of at least 2 ms for reversing at 1000 V. 4

36 Auxiliary contact modules Typ J7K -BM to J7K -EMA J7K -FM to J7K -GMA Rated impulse withstand voltage U imp Overvoltage category/pollution degree Rated insulation voltage U i 6000 V III/ 690 V AC Rated operational voltage U e 00 V AC Safe isolation to between coil and auxiliary 440 V AC 00 V AC IEC 6 contacts and between auxiliary contacts 440 V AC 00 V AC Rated operational current AC /240 V 6A I e 80/41 V 4A 00 V 1. A 2. A DC -1* 24/60/110/220V L/R 1 ms 10/6//1 A Conventional free air thermal current I th Control circuit reliability at U e = 24 V DC, 17 V,.4 ma Short -circuit rating without welding maximum fuse * Making and breaking currents to DC -1 time constant as stated 16 A Error rate H F <10-8 <1 fault operation in 100 million operations 16 A gl Pneumatic timer module General Typ J7KB -PTE -11, J7KB -PTD -11 Standards Mechanical lifespan AC 1x10 6 ops. DC IEC 947, EN 60947, UL, CSA 1x10 6 ops. Maximum operating frequency, mechanical AC 600 ops./h DC 600 ops./h Climatic proofing Damp heat, constant to IEC 68 Part 2 - Damp heat, cyclic to IEC 68 Part 2-0 Ambient temperature Open min./max. -2/+0 C Mounting position Mechanical shock resistance (sinusoidal 20 ms) Make/Brake contacts Degree of protection Protection against direct contact As required, except suspended 10/6 g IP00 Finger - and back -of -hand proof when actuated from the front by a perpendicular test finger (IEC 6) Terminal capacities Solid 1 x (0. -2.) mm 2 2 x (0. -2.) mm 2 Flexible with ferrule 1 x (0. -1.) mm 2 2 x ( ) mm 2 Solid or Stranded AWG Terminal screws Size M Pozidriv screwdriver Size 2 Standard screwdriver 0.8 x. mm 1x6mm Tightening torque 1.2 N

37 Contacts Typ J7KB -PTE -11, J7KB -PTD -11 Rated impulse withstand voltage U imp Overvoltage category/pollution degree Rated insulation voltage U i Rated operational voltage U e Rated operational current I e AC -1 Rated operational current I e DC - 1* Above 110 V and at L/R > 1 ms it is essential that t an arc - quenching device (RC suppressor) be used in parallel l with the contacts. t Required capacitor 1µF and resistor o. Ω series. Conventional free air thermal current I th L/R 1 ms e.g. contactor coils, solenoid valves, DC motors L/R 0 ms e.g. magnetic clutches, solenoid brakes 8000 V III/ 220/240 V 4A 80/41 V 4A 24 V 10 A 60 V 6A 110 V A 220 V 1A 24 V 4A 60 V 4A 110 V 1A 690 V AC 00 V AC 220 V 0. A Control circuit reliability at U e = 24 V DC, 17 V,,4 ma Error rate H F <10-8 <1 fault operation in 100 million operations Short -circuit rating without welding 00 V 6AgL Maximum fuse Current heat loss at conventional free air thermal current I th Per contact max. 0. W * Making and breaking currents to DC -1 time constant as stated 10 A Magnet system/control circuit Typ J7KB -PTE -11, J7KB -PTD -11 Duty factor 100 % DF Repetition accuracy <% Time deviation in relation to ambient temperature 0.2%/K Basedon+20 C Long -time deviation +1% Recovery time (after 100% time delay) Coil 0/60 Hz, mechanical lifespan 20 ms At 0 Hz approximately 0% less than listed under General 6

38 J7TK Overload relay General Typ J7TK -B -.. J7TK -D -.. J7TK -F -../FB J7TK -F -../FP Standards IEC 947, EN 60947, UL, CSA Climatic proofing Damp heat, constant to IEC 68 Part 2 - Damp heat, cyclic to IEC 68 Part 2-0 Ambient Open min./max. -2/+0 C* temperature Temperature compensation Mechanical shock resistance (sinusoidal 10 ms) Degree of protection Protection against direct contact Continuous 10 g IP00 J7TK -F -../GB J7TK -F -../GP Finger - and back -of -hand proof when actuated from the front by a perpendicular test finger (IEC 6) Main contacts Typ J7TK -B -.. J7TK -D -.. J7TK -F -../FB J7TK -F -../FP Rated impulse withstand voltage U imp 6000 V 8000 V Overvoltage category/pollution degree III/ Rated insulation voltage U i 690 V AC 1000 V AC Rated operational voltage U e 690 V AC 1000 V AC Safe insolation to IEC 6 between main 440 V AC contacts and auxiliary contacts and between main contacts J7TK -F -../GB J7TK -F -../GP Current setting A 6-7 A A A (J7TK -F -../GP) A (J7TK -F -../GB) Heat losses in the Minimum setting 2. W (7)W <16 W <16 W current paths (J7TK -D -7) Terminal capacities i (max.) Maximum setting 6W 7. (10) W (J7TK -D -7) <28 W <28 W Solid 2x(1-6)mm 2 2x(1-16) mm 2 ** 16 mm 2 16 mm 2 Flexible without ferrule mm 2 70 mm 2 Flexible with ferrule 2x(1-6)mm 2 1x2 mm 2 2x(1-10)mm 2 ** 0 mm 2 70 mm 2 Stranded mm 2 70 mm 2 Solid or stranded AWG 14-8 AWG 14-2 AWG 2 AWG 2/0 Terminal screws Size M4 M6 M8 M10 Pozidriv screwdriver Size 2 Size Standard screwdriver 1x6mm 1x6mm - - Hexagon socket -head - - 4mm mm screw SW Tightening torque 1.8 Nm. Nm 6Nm 10 Nm * Operating range to IEC947, EN ** When using two conductors, use equal cross -sections 7

39 Auxiliary and control circuits Typ Rated impulse withstand voltage U imp Overvoltage category/pollution degree Terminal capacities i 6000 V III/ Solid 2x(0.7-4)mm 2 Flexible with ferrule 2 x (0.7-2.) mm 2 Solid or Stranded Terminal screws Size M. Rated insulation voltage U i Rated operational voltage U e Pozidriv screwdriver Size 2 Standard screwdriver Tightening torque Safe insolation to IEC 6 between auxiliary contacts Conventional free air thermal current I th Rated operational current I e AC -1 Make/break k contacts Short -circuit rating without welding Maximum fuse 2xAWG x6mm Nm 00 V AC 00 V AC 240 V AC 6A 220/240 V 1. A/1. A 80/41 V 0. A/0.9 A 00 V 0. A/0.8 A AC -1* 24 V 0.9 A at L/R 1 ms; Make and break 60 V 0.7 A contacts 110 V 0.4 A 220 V 0.2 A 6AgL J7TK-B/-D/-F * Making and breaking currents to DC -1, time constant as stated 8

40 Dimensions Contactor J7K - AMA -..( - D) J7K-AMA-4(-D) M4 0 J7K - BM -..( - D) to J7K - EMA -..( - D) J7K - BM - 4( - D) a a4 a1 J7K Contactor BM(-D) BMA(-D) BM -4(-D) CM(-D) CMA(-D) a 4 (4) 4 (4) a1 () () b2 a4 - - () a (60) b 77 (77) 91 (91) 2M4x16 J7K -BM(A) J7K -CM(A) 2Mx16 J7K -DM(A) J7K -EM(A) b1 9 (9) 46 (46) b2 60 (60) 7 (7) c (with shroud) c (without shroud) 76. (101.) 86. (11.) 74 (99) 79 (104) c1 107 (12) 112 (17) c2 16 (161) 141 (166) J7TK-B Overload relays BM(-D) BMA(-D) CM(-D) CMA(-D) a 4 (4) 4 (4) b 120 (120) 1 (1) c6 90 (11) 96 (121) J7TK-D Overload relays DM(-D) DMA(-D) EM(-D) EMA(-D) a 60 (60) 60 (60) b 1 (1) 171 (171) c6 91 (116) 91 (116) J7K - FM -..( - D) to J7K - GMA -..( - D) J7K Contactor a DM(-D) DMA(-D) EM(-D) EMA(-D) FM(-D) FMA(-D) GM(-D) GMA(-D) a 60 (60) 70 (70) a1 0 (0) 60 (60) a4 70 (70) 80 (80) a 80 (80) 90 (90) 12 - b 98 (98) 118 (118) b1 49 (49) 9 (9) 6 7 b2 7 (7) 90 (90) c 97 (122) 102 (127) c1 10 (1) 1 (160) - - c c a4 With side mounting auxiliary contact module on J7K -CM( -D) to J7K -EMA( -D), with second side mounting auxiliary contact module J7K -FM -..SA on J7K -FM( -D) to J7K -GMA( -D). a With J7K -.. -N 4th pole module c1 With J7K -B(M) -.. auxiliary contact module c2 With J7KB -PTE(D) -11 pneumatic timer module 9

41 J7K -FM(A)( -D) + J7TK -F -../FP J7K -GM(A)( -D) + J7TK -F -../GP a1 J7TK-F Overload relays -/FP -/GP a a b2 b b a7 b c b6 b J7K-FM(A)(-D) + 2 M x 20 J7TK -F -../FP 2 M x 20 J7K-GM(A)(-D) + 2 M6 x 20 J7TK -F -../GP 2 M6 x 20 J7TK -B + J7TKB -B J7TK -D + J7TKD -B b1 a2 a a J7TKB -B = 2 M4 x 12 J7TKB -D = 2 M x 1 Overload relays J7TK-B + J7TKB-B a 8 86 a a a 7 7 a 7. - b 60 c c J7TK-D + J7TKD-B J7TK -F -../(F)(G)P Knockout; Supplied closed J7K-FM(A) J7K-GM(A) Overload relays J7TK-F../FP J7TK-F../GP a a a a b b b2 1 1 c 1 1 c d e

42 J7TK -F -../(F)(G)B Overload relays J7TK-F-../FB J7TK-F-../GB a a b b c 1 1 d e 6 7 Accessories Suppressors J7KA -RC J7KA -VG J7KB(F) -RC J7KB -VG J7KB -FD RC/VG/FD a b 1 c 0 Mechanical interlock J7KA -MV J7KB -MV J7KF -MV J7K Contactor + mechanical interlock BM(-D) + J7KB-MV EMA(-D)+ J7KB-MV a 1 0 FM(-D) + J7KF-MV GMA(-D) + J7KF-MV 41

Type: DILEM 10(220V50HZ,240V60HZ) Article No.:

Type: DILEM 10(220V50HZ,240V60HZ) Article No.: Type: DILEM 10(220V50HZ,240V60HZ) Article No.: 051785 Ordering information Actuating voltage Description Connection technique 380 V 400 V I e A 8.8 Max. rating for three phase motors, 50 AC 3 220 V 230

More information

Type: DILEM 10 G(24VDC) Article No.:

Type: DILEM 10 G(24VDC) Article No.: Type: DILEM 10 G(24VDC) Article No.: 010213 Ordering information Description Connection technique Rated operational current AC 3 380 V 400 V I e A 9 Max. rating for three phase motors, 50 60 Hz AC 3 220

More information

Type: DILM80(110V50HZ,120V60HZ) Article No.: Sales text Contactor,37kW/400V,AC operated. Ordering information

Type: DILM80(110V50HZ,120V60HZ) Article No.: Sales text Contactor,37kW/400V,AC operated. Ordering information Type: DILM80(110V50HZ,120V60HZ) Article No.: 239399 Sales text Contactor,37kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current AC 3 380 V 400

More information

Type: DILM95(230V50HZ,240V60HZ) Article No.: Sales text Contactor,45kW/400V,AC operated. Ordering information

Type: DILM95(230V50HZ,240V60HZ) Article No.: Sales text Contactor,45kW/400V,AC operated. Ordering information Type: DILM95(230V50HZ,240V60HZ) Article No.: 239480 Sales text Contactor,45kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current AC 3 380 V 400

More information

Description Basic devices with positive operation contacts. Standards IEC/EN 60947, EN , VDE 0660, UL, CSA

Description Basic devices with positive operation contacts. Standards IEC/EN 60947, EN , VDE 0660, UL, CSA Contactor relay, 2N/O+2N/C, AC Part no. DILA-22(24V60HZ) Catalog No. 276390 Eaton Catalog No. XTRE10B22B6 Delivery program Product range DILA relays Application Contactor relays Description Basic devices

More information

Instructions Contact numbers to EN Coil terminal markings to EN Integrated diode-resistor combination Coil rating 2.

Instructions Contact numbers to EN Coil terminal markings to EN Integrated diode-resistor combination Coil rating 2. Delivery program Contactor relay, 2N/O+2N/C, DC current Part no. DILER-22-G(24VDC) Catalog No. 010042 Eaton Catalog No. XTRM10A22TD EL-Nummer 4130354 (Norway) Product range DILER Mini-contactors Application

More information

Description Basic devices with positive operation contacts

Description Basic devices with positive operation contacts Contactorrelay,3N/O+1N/C,DCcurrent Partno. DILA-31(24VDC) Articleno. 276379 CatalogNo. XTRE10B31TD Deliveryprogramme Product range DILA relays Application Contactor relays Description Basic devices with

More information

J7M-AM/-BM. Motor--protective circuit--breaker system. J7M -BM System IEC 947, EN IEC 947, EN 60947

J7M-AM/-BM. Motor--protective circuit--breaker system. J7M -BM System IEC 947, EN IEC 947, EN 60947 Motor--protective circuit--breaker system J7M -AM System Rated operational current 25 A. Switching capacity up to 10 A, 100 ka/415 V. Switching capacity 16 A, 20 A, 25 A, 16 ka/415 V. Fixed short--circuit

More information

Description Basic devices with positive operation contacts. Connection to SmartWire-DT yes in conjunction with DIL-SWD SmartWire DT contactor module

Description Basic devices with positive operation contacts. Connection to SmartWire-DT yes in conjunction with DIL-SWD SmartWire DT contactor module DATASHEET - DILA-22(24VDC) Delivery program Contactor relay, 2N/O+2N/C, DC current Part no. DILA-22(24VDC) Catalog No. 276414 Eaton Catalog No. XTRE10B22TD EL-Nummer 4130211 (Norway) Product range DILA

More information

Description Basic devices with positive operation contacts. Standards IEC/EN 60947, EN , VDE 0660, UL, CSA

Description Basic devices with positive operation contacts. Standards IEC/EN 60947, EN , VDE 0660, UL, CSA DATASHEET - DILA-22(230V50HZ,240V60HZ) Delivery program Contactor relay, 2N/O+2N/C, AC Part no. DILA-22(230V50HZ,240V60HZ) Catalog No. 276399 Eaton Catalog No. XTRE10B22F EL-Nummer 0004130208 (Norway)

More information

Type: DILM40(RDC24) Article No.:

Type: DILM40(RDC24) Article No.: Type: DILM40(RDC24) Article No.: 277780 Ordering information Rated operational current AC 3 400 V I e A 40 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase motors, 50

More information

DATASHEET - ETR4-70-A. Delivery program. Timing relay, 2W, 0.05s-100h, multi-function, VAC/DC, potentiometer connection

DATASHEET - ETR4-70-A. Delivery program. Timing relay, 2W, 0.05s-100h, multi-function, VAC/DC, potentiometer connection DATASHEET - ETR4-70-A Delivery program Timing relay, 2W, 0.05s-100h, multi-function, 24-240VAC/DC, potentiometer connection Part no. ETR4-70-A Catalog No. 031888 Eaton Catalog No. XTTR6A100H70B EL-Nummer

More information

DATASHEET - ETR4-51-A. Delivery program. Technical data General. Timing relay, star-delta, 50 ms, 1W, 3-60s, VAC/DC

DATASHEET - ETR4-51-A. Delivery program. Technical data General. Timing relay, star-delta, 50 ms, 1W, 3-60s, VAC/DC DATASHEET - ETR4-51-A Timing relay, star-delta, 50 ms, 1W, 3-60s, 24-240VAC/DC Part no. ETR4-51-A Catalog No. 031884 Eaton Catalog No. XTTR6A60S51B EL-Nummer 0004133308 (Norway) Delivery program Product

More information

Industrial Controls. Catalog IC SIRIUS. Answers for industry.

Industrial Controls. Catalog IC SIRIUS. Answers for industry. Industrial Controls Catalog IC 10 2012 SIRIUS Answers for industry. Contactor Relays Siemens AG 2012 Overview Standards IEC 60947-1, EN 60947-1, IEC 60947--1, EN 60947--1 The 3TH42 and 3TH43 contactor

More information

PKZ 2 Manual Motor Protectors Technical Data

PKZ 2 Manual Motor Protectors Technical Data 08/066 PKZ 2 Manual Motor Protectors General Standards UL 508, CSA C 22.2 No. 14, IEC/EN 60 947, VDE 0660 GL, LR, DNV, PRS, BV, RINA, RS, EZU, MEEI Climatic proofing Damp heat, constant, to IEC 60 068-2-3

More information

Controls Contactors and Contactor Assemblies Special Applications

Controls Contactors and Contactor Assemblies Special Applications Controls Contactors and Contactor Assemblies Special Applications Price groups 1B, 1H /2 Introduction More information can be found on the Internet: see the opening information, page 13 - Contactors for

More information

XT IEC Power Control Miniature Controls

XT IEC Power Control Miniature Controls Product Family Overview May 07 Contents Description Page Selection................ Product Selection.......... Non-reversing Mini Contactors......... Reversing Mini Contactors............. Star-Delta (Wye-Delta)

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Type: EASY719 AC RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC. Description

Type: EASY719 AC RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC. Description Type: EASY719 AC RC Article No.: 274115 Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC Description 12 digital inputs 6 relay outputs LCD display Operating buttons Screw terminals

More information

Catalog 200 Contactors up to 115 A Motor Starters up to 55 kw 03/2009

Catalog 200 Contactors up to 115 A Motor Starters up to 55 kw 03/2009 Catalog 00 Contactors up to 5 A Motor Starters up to 55 kw 03/009 Kraus & Naimer The development of the Blue Line rotary switch, contactor and motor starter product ranges is based on more than hundred

More information

Motor-protective circuit-breaker, 3p, Ir=40-50A, screw connection. Product range PKZM4 motor protective circuit-breakers up to 65 A

Motor-protective circuit-breaker, 3p, Ir=40-50A, screw connection. Product range PKZM4 motor protective circuit-breakers up to 65 A DATASHEET - PKZM4-50 Delivery program Motor-protective circuit-breaker, 3p, Ir=40-50A, screw connection Part no. PKZM4-50 Catalog No. 222355 Eaton Catalog No. XTPR050DC1NL EL-Nummer 0004355161 (Norway)

More information

Type CP-S, CP-C & CP-A Switch mode

Type CP-S, CP-C & CP-A Switch mode Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting

More information

Type: EASY719 DA RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC. Description

Type: EASY719 DA RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC. Description Type: EASY719 DA RC Article.: 274117 Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display

More information

AC-3 AC-1 230V 400/415V 500V 690V 115V 230V 200V 230V 460V 575V N.O. N.C. Qty. Cat. No. Screw Terminals. Spring Clamp Terminals. 40 C Pkg.

AC-3 AC-1 230V 400/415V 500V 690V 115V 230V 200V 230V 460V 575V N.O. N.C. Qty. Cat. No. Screw Terminals. Spring Clamp Terminals. 40 C Pkg. Bulletin -K, -K IEC Miniature Contactors Overview/Product Selection Product Selection -Pole AC- and DC-Operated Contactors Bulletin -K/-K IEC Miniature Contactors Compact size Same dimensions for AC and

More information

Mini Contactors. Mini Contactor Relays 4-pole 8 Auxiliary Contact Blocks. Interface Contactor Relays. Mini Contactors 10 Auxiliary Contact Blocks

Mini Contactors. Mini Contactor Relays 4-pole 8 Auxiliary Contact Blocks. Interface Contactor Relays. Mini Contactors 10 Auxiliary Contact Blocks Mini Contactors Mini Contactor Relays 4-pole 8 Auxiliary Contact Blocks Interface Contactor Relays Mini Contactors 10 Auxiliary Contact Blocks Mini Contactors With Fast On Tab Connectors 12 Mini Contactors

More information

Characteristics 5 TeSys k contactors and reversing contactors

Characteristics 5 TeSys k contactors and reversing contactors 90 Characteristics contactors k contactors and reversing contactors Environment characteristics Conforming to standards IEC 60947, NF C 63-110, VDE 0660, BS 424 Product certifications LCp and LPp K06 to

More information

Utilization category DC-1 DC-3 DC-5 L/R 1 ms L/R 2 ms L/R 7.5 ms

Utilization category DC-1 DC-3 DC-5 L/R 1 ms L/R 2 ms L/R 7.5 ms controls IEC Technical data D.C. Power circuit switching Utilization category DC- DC- DC- L/R ms L/R ms L/R 7. ms + + + V A 6.0 6.0 6.0 8 V A 6.0 8.0.0 60 V A 6.0.0. V A 7.0. 0. 0 V A 0.8 0. V A 6.0 6.0

More information

Output of three-phase motors at 50 Hz and 400 V

Output of three-phase motors at 50 Hz and 400 V RT0, RH Coupling Relays (Interfaces) Description DC operation IEC 0 947 and EN 0 947 (VDE 00) The RT0 coupling relays for switching motors and RH for auxiliary circuits are laid out to the special requirements

More information

Micro Contactors. Micro Contactor Relays 10. Micro Contactors 11. Micro Contactors With Solder Pins 12. Coil voltages 12. Micro Reversing Contactor 13

Micro Contactors. Micro Contactor Relays 10. Micro Contactors 11. Micro Contactors With Solder Pins 12. Coil voltages 12. Micro Reversing Contactor 13 Micro Contactor Relays 10 Micro Contactors 11 Micro Contactors With Solder Pins 12 Coil voltages 12 Micro Reversing Contactor 13 Technical Data 14 Dimensions 18 D946E 9 Micro Contactor Relays 4-pole AC

More information

NZMH4, NZM(H)6(B), NZM(H)9, NZM12 Technical Data

NZMH4, NZM(H)6(B), NZM(H)9, NZM12 Technical Data Circuit Breakers, 09/098 Molded case circuit breakers 3 pole NZMH 4-...-C 1) NZM6B.../ZM6A...- Frame size A 80 125 125 IEC 60 947-2 Electrical Ratings Rated impulse withstand voltage U imp V 8000 8000

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Easy measuring, reliable monitoring and flexible planning - the EMR, ETR and EMT relays

Easy measuring, reliable monitoring and flexible planning - the EMR, ETR and EMT relays EMR6 EMT6 ETR4 www.eaton.eu Easy measuring, reliable monitoring and flexible planning - the EMR, ETR and EMT relays The measuring and monitoring of industrial applications made simple - with the EMR6 With

More information

Moeller Electric Corporation

Moeller Electric Corporation EMR4-I Current Monitoring Relays 02/0053 EMR4-I1-2-A EMR4-I15-2-A EMR4-I15-2-B Mechanical lifespan operations x10 6 30 30 30 24-h cycle, 55 C, 93 % relative humidty, 96 h Ambient temperature min./max.

More information

TeSys contactors. TeSys D contactors. IEC/EN , IEC/EN , UL 508, CSA C22.2 n 14. Protection against direct fi nger contact IP 2X

TeSys contactors. TeSys D contactors. IEC/EN , IEC/EN , UL 508, CSA C22.2 n 14. Protection against direct fi nger contact IP 2X Characteristics Contactor type LC1 D09 D18 DT20 and DT25 Environment Rated insulation voltage (Ui) Conforming to IEC 097--1, overvoltage category III, degree of pollution: 3 Conforming to UL, CSA V 00

More information

Bulletin 100S-C/104S-C Safety Contactors. Bulletin 700S-CF Safety Control Relays. Table of Contents. Selection Guide

Bulletin 100S-C/104S-C Safety Contactors. Bulletin 700S-CF Safety Control Relays. Table of Contents. Selection Guide Bulletin S-C/S-C Safety Contactors Bulletin 7S-CF Safety Control Relays Selection Guide Table of Contents Description Page Bulletin S-C/S-C Safety Contactors Product Selection.................................

More information

The CWC0 compact contactors are offered as a complete solution for switching and controlling motors.

The CWC0 compact contactors are offered as a complete solution for switching and controlling motors. Compact Contactors The CWC compact contactors are offered as a complete solution for switching and controlling motors. Main Features Contactors with screw s for C-3 operation up to Contactors with spring

More information

s s s 3-60 s min min 3-60 min h h 3-60 h V AC, 50/60 Hz

s s s 3-60 s min min 3-60 min h h 3-60 h V AC, 50/60 Hz HPL11002EN DILETTiming relays Rated operational current AC-11 230 V 400 V I th I e I e A A A A A Conventional thermal current Time Range Voltage Article No. See price list Std. pack On-delayed Timing functions

More information

Contactors and Contactor Assemblies

Contactors and Contactor Assemblies s for Switching Motors Technical data General data Permissible mounting position The contactors are designed for operation on a vertical mounting surface. C and DC operation S3 3RT14 46 For DC operation

More information

Block Contactors. Contents. Panorama 3-pole Contactors... 2/2 4-pole Contactors... 2/4

Block Contactors. Contents. Panorama 3-pole Contactors... 2/2 4-pole Contactors... 2/4 /0 Block Contactors Contents Panorama -pole Contactors... / 4-pole Contactors... /4 -pole Contactors: Description and Ordering Details A 9... A 0 Contactors (a.c. Operated)... /6 A 4... AF 60 Contactors

More information

New Products Catalogue 2009 Safety Relays ESR5

New Products Catalogue 2009 Safety Relays ESR5 www.moeller.net New Products Catalogue 2009 Safety Relays ESR5 u Description Functional safety on machines monitoring with safety relays ESR5 Emergency-stop circuits Monitoring of movable guards with guard

More information

Capacitor Switching Contactors

Capacitor Switching Contactors Capacitor Switching D385E51 Technical catalogues and news under: www.benedict.at Motor-Starter Mini- Overload Relays Capacitor Switching Motor-Starters Modular Circuit Breakers M4-32T... up to 32A M4-32R..

More information

Breakcontact,Front. Articleno Deliveryprogramme. Product range RMQ-Titan (drilling dimensions 22.5 mm) Basic function Accessories

Breakcontact,Front. Articleno Deliveryprogramme. Product range RMQ-Titan (drilling dimensions 22.5 mm) Basic function Accessories Breakcontact,Front Partno. M22-K01 Articleno. 216378 Deliveryprogramme Product range RMQ-Titan (drilling dimensions 22.5 mm) Basic function Accessories Standard/Approval UL/CSA, IEC Construction size NZM1/2/3/4

More information

For non-electrical quantities

For non-electrical quantities Controlgear 3UG3 monitoring relays 3RS17 interface converters N nsb0346h nsb0348h nsb0775h For electrical quantities For non-electrical quantities 3RS17 interface converter Selection and ordering data

More information

Control module CP-A CM

Control module CP-A CM 2CDC 271 002 F0t05 Features Pluggable onto redundancy unit CP A RU Threshold values adjustable (14 28 V) One relay output per monitored input / channel Approvals H UL 508, CAN/CSA C22.2 No.14 H UL 60950,

More information

PHOENIX CONTACT - 09/2009

PHOENIX CONTACT - 09/2009 Electronic miniature circuit-breaker CLIPLINE Data sheet 03906_en_0 PHOENIX CONTACT - 09/2009 Description The EC-E... electronic miniature circuit-breaker selectively protects all 24 V DC load circuits

More information

Approved Standards. Ordering Information. Mini Contactor Relays 4-pole J7KNA-AR. Model Number Legend. Main contactor. Accessories

Approved Standards. Ordering Information. Mini Contactor Relays 4-pole J7KNA-AR. Model Number Legend. Main contactor. Accessories Mini Contactor Relays 4-pole J7KN-R ) Main contactor C & DC operated 4-, 6- and 8-pole versions in different configurations Mirror contacts Screw fixing and snap fitting (35 mm DIN rail) Rated current

More information

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet

Electronic timer CT-SDS.22 Star-delta change-over with 2 n/o contacts Data sheet CDC 0 F0t07 Features Rated control supply voltage -8 V DC, -0 V AC Single-function timer with star-delta change-over One device includes 7 time ranges (0.0 s - 0 min) n/o contacts LEDs for status indication

More information

3 - Protection components Circuit-breakers

3 - Protection components Circuit-breakers Contents - Protection components Circuit-breakers for the motor protection Selection guide..............................................page /2 Thermal-magnetic motor circuit-breakers Selection guide..............................................page

More information

Thermistor motor protection relays

Thermistor motor protection relays Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /

More information

Electronic timer CT-SDS.22

Electronic timer CT-SDS.22 CDC 0 F0t07 Features Rated control supply voltage 8 V DC, 0 V AC Single function timer with star delta change over One device includes 7 time ranges (0.0 s 0 min) n/o contacts LEDs for status indication

More information

60 Series - General purpose relays 6-10 A. Features Plug-in mount 10 A General purpose relay

60 Series - General purpose relays 6-10 A. Features Plug-in mount 10 A General purpose relay Series - General purpose relays - 0 A Features Plug-in mount 0 A General purpose relay.. & pole changeover contacts Cadmium Free contacts (preferred version) AC coils & DC coils UL Listed (certain relay/socket

More information

Three-phase monitoring relays CM-PFE and CM-PFE.2

Three-phase monitoring relays CM-PFE and CM-PFE.2 Data sheet Three-phase monitoring relays CM-PFE and CM-PFE.2 The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251

More information

NS..S contactor relays - with spring terminals AC operated

NS..S contactor relays - with spring terminals AC operated NS..S contactor relays - with spring terminals AC operated NSES 1SBC101015F00 Description NS..S contactor relays are used for switching auxiliary and control circuits. These contactor relays are designed

More information

Index. Capacitor Switching - 2 Contactors. Typical Circuit Diagram 2. Auxiliary Contact Blocks 2. Contactors 3. Dimensions 3. Technical Data 4,5,6

Index. Capacitor Switching - 2 Contactors. Typical Circuit Diagram 2. Auxiliary Contact Blocks 2. Contactors 3. Dimensions 3. Technical Data 4,5,6 Index Index Page Capacitor Switching - 2 Contactors Typical Circuit Diagram 2 Auxiliary Contact Blocks 2 Contactors 3 Dimensions 3 Technical Data 4,5,6 Contactor operation 7 Function 8 Construction 9 Oscillogram

More information

Switching Devices Contactors and Contactor Assemblies for Switching Motors

Switching Devices Contactors and Contactor Assemblies for Switching Motors Switching Devices Contactors and Contactor Assemblies for Switching Motors groups 41B, 41H / Introduction Power contactors for switching motors /5 General data /11 SIRIUS RT10 contactors, -pole,... 50

More information

VEO. V2PF480Y/277VS01 Art.Nr.: B TECHNICAL DATA

VEO. V2PF480Y/277VS01 Art.Nr.: B TECHNICAL DATA Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Status indication LED U: Supply voltage

More information

Power Electronics. POWERSWITCH Solid-State Contactor BF 9250, BH 9250

Power Electronics. POWERSWITCH Solid-State Contactor BF 9250, BH 9250 Power Electronics POWERSWITCH Solid-State Contactor, BH 9250 02342 According to IEC/E 60 947-4-2, IEC/E 60 947-4-3 1-, 2- and 3-pole models Load current up to 50 A For AC load up to 480 V Switching at

More information

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units

10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units BETA Switching Transformers, Bells and Socket Outlets /2 Product overview /3 4AC3 0, 4AC3 1 bell transformers /5 4AC3 4... 4AC3 transformers for permanent loads /8 4AC2 4 power supply units / 7LQ2 2 bells

More information

Ratings for Switching AC Motors AC-2, AC-3, AC / /

Ratings for Switching AC Motors AC-2, AC-3, AC / / Bulletin -C/-C Overview/Product Selection Product Selection -Pole AC- and DC-Operated Contactors Ie [A] Bulletin -C/-C Compact sizes from kw/ Hp ( A) AC and DC coil control Common accessories for all contactor

More information

Electronic timer CT-SDD.22

Electronic timer CT-SDD.22 CDC 099 F0t0 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c U: green LED V control supply voltage applied W

More information

62 Series - Power relays 16 A. Features / /

62 Series - Power relays 16 A. Features / / 6 Series - Power relays 6 A Features 6. / 6.3 6.-0300 / 6.3-0300 Printed circuit mount 6 A Power relay & 3 Pole changeover contacts or NO ( 3 mm contact gap) AC coils & DC coils Reinforced insulation between

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Electronic timer CT-TGD.22

Electronic timer CT-TGD.22 2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents

Current monitoring relays CM-SRS.2 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

2 Pole CO, 8 A Plug-in 2 CO (DPDT) 1 CO (SPDT) 8/15 16/25* 250/ /400 2,000 4, /0.5/ /0.5/ (5/5) 300 (10/5)

2 Pole CO, 8 A Plug-in 2 CO (DPDT) 1 CO (SPDT) 8/15 16/25* 250/ /400 2,000 4, /0.5/ /0.5/ (5/5) 300 (10/5) 46 Series - Relays for railway applications 8-16 A 46 SERIES Features Plug-in power relays: 8 A, 2 pole 16 A, 1 pole Complies with EN 45545-2:2013 (protection against fire of materials), EN 61373 (resistance

More information

VEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA

VEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA P Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Control elements Asymmetry Status

More information

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents

Current monitoring relays CM-SRS.2 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.2 For single-phase AC/DC currents The CM-SRS.2 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

Three-phase monitoring relay CM-PFS

Three-phase monitoring relay CM-PFS Data sheet Three-phase monitoring relay CM-PFS The CM-PFS is a three-phase monitoring relay that is used to monitor three phase mains for incorrect phase sequence and phase failure. All devices are available

More information

Semiconductor contactors, Solid-state relays

Semiconductor contactors, Solid-state relays Semiconductor contactors, Solid-state relays Content Benefits and advantages... 338 Approvals and marks... 338 Semiconductor contactors... 339 Ordering details... 339 R100.xx, single-phase... 339 R300.xx,

More information

AF AF V50/60HZ-DC Contactor. General Information. Ordering. Popular Downloads. Dimensions. Technical AF

AF AF V50/60HZ-DC Contactor. General Information. Ordering. Popular Downloads. Dimensions. Technical AF ABB AF12-30-01-14 250-500V50/60HZ-DC Contactor General Information Extended Product Type Product ID AF12-30-01-14 1SBL157001R1401 EAN 3471523110441 Catalog Description Long Description AF12-30-01-14 250-500V50/60HZ-DC

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with OFF-delay and 10 time ranges. All electronic timers from the CT-S

More information

22 Series Relays. Technical Data...1. Specifications...2. Model Number Structure - Relays...3. Model Number Selection

22 Series Relays. Technical Data...1. Specifications...2. Model Number Structure - Relays...3. Model Number Selection Relays 22 Technical Data...1 Specifications...2 Model Number Structure - Relays...3 Model Number Selection... 4-5 Electrical Characteristics...6 Accessories...7 Dimensions...8 Instructions...10 Safety

More information

Solid-State Soft Starters

Solid-State Soft Starters Selection and ordering data Rated operational voltage U e V Soft starters for three-phase asynchronous motors 3RW30 25-1B14 3RW30 35-1B14 t ambient temperature 40 C Size Order No. Price Weight Pack. Rated

More information

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 For single-phase AC/DC currents The CM-SRS.1 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent

More information

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)

Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,

More information

LC2D09BL REVERSING CONTACTOR 575VAC 9A IEC

LC2D09BL REVERSING CONTACTOR 575VAC 9A IEC Product datasheet Characteristics LC2D09BL REVERSING CONTACTOR 575VAC 9A IEC Price* : 107.62 GBP Main Range Product name Product or component type Device short name Contactor application Utilisation category

More information

Ratings for Switching AC Motors AC-2, AC-3, AC / /

Ratings for Switching AC Motors AC-2, AC-3, AC / / Bulletin S-C/S-C IEC Safety Contactors Overview/Product Selection Product Selection -Pole AC- and DC-Operated Contactors Bulletin S-C/S-C IEC Safety Contactors Mechanically linked N.C. auxiliary contacts

More information

Thermistor motor protection relays

Thermistor motor protection relays Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /

More information

Electronic timer CT-MFS.21

Electronic timer CT-MFS.21 2CDC 251 053 F0t07 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c Rotary switch for the preselection of the

More information

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts

Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with true OFF-delay and 10 time ranges. All electronic timers from

More information

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents

Current monitoring relays CM-SRS.1 for single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.1 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact

More information

Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC

Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC Data sheet Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC The CM-IWS.1 serves to monitor insulation resistance in accordance with IEC

More information

CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. UL 508, CAN/CSA C22.2 No.14 GL GOST CB scheme CCC

CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. UL 508, CAN/CSA C22.2 No.14 GL GOST CB scheme CCC 2CDC 251 048 F0t08 CM-MPS.11 2CDC 251 049 F0t08 CM-MPS.21 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage as well as phase unbalance

More information

Three-phase monitoring relays

Three-phase monitoring relays 2CDC 251 046 F0t08 Features Monitoring of three-phase mains for phase sequence, phase failure, phase unbalance Threshold value for phase unbalance adjustable as absolute value Tripping delay can be adjusted

More information

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents

Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents Data sheet Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents The CM-SRS.M1 is an electronic current monitoring relay that monitors single-phase mains (DC or AC) for over- and undercurrent

More information

ABB NEW. Multifunctional three-phase monitoring relays. CM-MPS.23 and CM-MPS.43 Data sheet. Features J. Approvals. Marks.

ABB NEW. Multifunctional three-phase monitoring relays. CM-MPS.23 and CM-MPS.43 Data sheet. Features J. Approvals. Marks. 2CDC 251 052 F0t08 CM-MPS.23 2CDC 251 053 F0t08 CM-MPS.43 - relay status, timing - fault message - fault message Adjustment of the tripping delay t V Adjustment of the threshold value for overvoltage 6

More information

2 or 4 pole changeover contact Plug-in/Faston 187

2 or 4 pole changeover contact Plug-in/Faston 187 56 Miniature power relays 56 Plug-in - Power relay, & 4 pole Flange mount option - (Faston 87, 4.8 x 0.5 mm termination) C coils & DC coils Lockable test button and mechanical flag indicator Cadmium Free

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

LC1D25BL TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 25 A - 24 V DC coil

LC1D25BL TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 25 A - 24 V DC coil Product data sheet Characteristics LC1D25BL TeSys D contactor - 3P(3 NO) - AC-3 -

More information

Power Electronics. POWERSWITCH Semiconductor Contactor BF 9250, BH 9250

Power Electronics. POWERSWITCH Semiconductor Contactor BF 9250, BH 9250 Power Electronics POWERSWITCH Semiconductor Contactor, BH 9250 02342 According to IEC/E 60 947-4-2, IEC/E 60 947-4-3 1-, 2- and 3-pole models Load current up to 50 A For AC load up to 480 V Switching at

More information

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages

Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages Data sheet Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages The CM-EFS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of

More information

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC

Measuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC 2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from

More information

Electronic Circuit Breaker with reset input ESS20-1..

Electronic Circuit Breaker with reset input ESS20-1.. Electronic Circuit Breaker with reset input ESS0-.. Description The special device ESS0-.. is a further extension of the product line electronic circuit breakers. Type ESS0-.. has a width of only. mm and

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

Relay interface modules A

Relay interface modules A 4C SЕRIES Relay interface modules 8-10 - 16 A Escalators Road / tunnel lighting Hoists and cranes Carousel warehouses Control panels Panels for electrical distribution FINDER reserves the right to alter

More information

ABB NEW. Three-phase monitoring relays. CM-PVS.31 and CM-PVS.41 Data sheet. Features J. Approvals. Marks. Order data. Order data - Accessories

ABB NEW. Three-phase monitoring relays. CM-PVS.31 and CM-PVS.41 Data sheet. Features J. Approvals. Marks. Order data. Order data - Accessories 2CDC 251 042 F0t08 CM-PVS.31 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage Threshold values for over- and undervoltage are adjustable

More information

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment

Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED

More information

V2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC

V2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC P AC/DC voltage monitoring Multifunction Supply voltage 24 V DC or 230V AC/DC Supply circuit = Measuring circuit 1 change-over contact Width 22,5 mm Control elements Tripping delay Maximum threshold Minimum

More information