PERFORMANCE EVALUATION OF OPTICAL AMPLIFIER IN WDM SYSTEM PEH PO ING

Transcription

1 i PERFORMANCE EVALUATION OF OPTICAL AMPLIFIER IN WDM SYSTEM PEH PO ING This report is submitted in partial of the requirement for the award of Bachelor of Electronic Engineering (Telecommunication Electronics) With Honours Faculty of Electronic and Computer Engineering Universiti Teknikal Malaysia Melaka June 2012

2 ii UNIVERSTI TEKNIKAL MALAYSIA MELAKA FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER BORANG PENGESAHAN STATUS LAPORAN PROJEK SARJANA MUDA II Tajuk Projek : PERFORMANCE EVALUATION OF OPTICAL AMPLIFIER IN WDM SYSTEM Sesi Pengajian : 1 1 / 1 2 Saya PEH PO ING mengaku membenarkan Laporan Projek Sarjana Muda ini disimpan di Perpustakaan dengan syaratsyarat kegunaan seperti berikut: 1. Laporan adalah hakmilik Universiti Teknikal Malaysia Melaka. 2. Perpustakaan dibenarkan membuat salinan untuk tujuan pengajian sahaja. 3. Perpustakaan dibenarkan membuat salinan laporan ini sebagai bahan pertukaran antara institusi pengajian tinggi. 4. Sila tandakan ( ) : SULIT* *(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia seperti yang termaktub di dalam AKTA RAHSIA RASMI 1972) TERHAD** **(Mengandungi maklumat terhad yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan) TIDAK TERHAD Disahkan oleh:

3 iii DECLARATION I hereby declare that this report is result of my own effort except for works that have been cited clearly in the references. Signature Name :. : PEH PO ING Date : 15 th JUNE 2012

4 iv I hereby declare that I have read this report and in my opinion this report is sufficient in terms of scope and quality for the award of Bachelor of Electronic Engineering (Telecommunication Engineering) with Honours Signature Supervisor s Name :. : MR. CHAIRULSYAH B. ABDUL WASLI Date : 15 th JUNE 2012

5 v DEDICATION Special dedicated to my beloved father, Peh Kim Pong and my mother, Tee Siew Ching.

6 vi ACKNOWLEDGEMENT First and foremost, I would like to convey my sincere appreciation to my supervisor Mr. Chairulsyah B. Abdul Wasli for his assistance and guidance toward the progress of this thesis project. In the other hand, I also would like to extend my sincere gratitude to my ex-supervisor, Puan Zaiton Abdul Mutalip for her patience, concern and encouragement throughout the preparation of this thesis. Besides that, I would like to dedicated my deepest thank to my beloved family members for their moral and financial support while completing my tertiary education. Furthermore, thanks to all the lectures and my fellow course mate for their cooperation, opinion and sharing. Last but not least, I would like to express my thanks to the technicians and librarians of University of Technical Malaysia Malacca (UTeM) for their valuable resources providing in completing my thesis.

7 vii ABSTRACT This report explores on how to evaluate the performance of optical amplifier which are Erbium-Doped Fiber Amplifier (EDFA), Raman Amplifier, and Hybrid Raman and Erbium-Doped Fiber Amplifier (HFAs) which are technologies for future dense wavelength-division-multiplexing (DWDM) multiterabit systems. After that, the best optical amplifier will be chosen among all of these amplifiers. This report will be explained the fundamental knowledge, the characteristic of these three types of amplifier and the simulation process involved in completing the project. The methods used to achieve the objectives are also clarified throughout the report.

8 viii ABSTRAK Laporan ini menghuraikan tentang bagaimana untuk menilai prestasi penguat optic Erbium-Doped Fiber Amplifier (EDFA), Raman Amplifier, and Hybrid Raman and Erbium-Doped Fiber Amplifier (HFAs) yang merupakan teknologi wavelength-division-multiplexing (WDM) sistem multiterabit untuk masa depan. Peguat optic yang terbaik akan dipilih dikalangan ketiga-tiga jenis peguat tersebut. Laporan ini akan menerangkan pegetahuan asas, cirri-ciri ketiga-tiga jenis peguat dan proses simulasi yang terlibat dalam menyiapkan projek ini. Kaedah-kaedah yang digunakan untik mencapai objektif juga dijelaskan sepanjang laporan ini.

9 ix CONTENT CHAPTER TITLE PAGES TITLE STATUS VERIFICATION FORM STUDENT DECLARATION SUPERVISOR DECLARATION DEDICATION ACKNOWLEDGEMENT ABSTRACT ABSTRAK CONTENT LIST OF TABLE LIST OF FIGURE LIST OF APPENDIX LIST OF ABBREVIATIONS i ii iii iv v vi vii viii ix xiii xv xvii xviii I INTRODUCTION 1.0 Project Background Objectives of Project Scopes of Work Problems Statement Methodology Thesis Structure 3

10 x II LITERATURE REVIEW 2.1 Fiber Optic is Green Technology Wavelength-Division-Multiplexing Optical Cables Fiber Core Index Profile Single-Mode Step-Index Optical Fiber Multimode Step-Index Optical Fiber Multimode Gradient-Index Optical Fiber Advantages and Disadvantages of Single-mode Step-index, Multimode Step Index, and Multimode Gradient-Index Performance of Optical Amplifier Gain Attenuation Loss Attenuation Coefficient Return Loss Insertion Loss Noise Figure Optical Signal-to-Noise Ratio Bit Error Rate Eye-Pattern Optical Amplifier Erbium-Doped Fiber Amplifier Raman Amplifier Semiconductor Optical Amplifier Comparison of EDFA, Raman Amplifier and SOA Advantages and Disadvantages of EDFA, Raman Amplifier and SOA Hybrid Raman and Erbium-Doped Fiber Amplifier (HFAs) 21

11 xi III METHODOLOGY 3.1 Project Flow Chart Project Block Diagram Calculation of Gain, Noise Figure Design Parameter for Erbium Doped Fiber Amplifier Design Parameter for Raman Amplifier Design Parameter for Hybrid Amplifier Wavelength-Division Multiplexing (WDM) Lab Test 30 IV RESULT 4.1 Calculation Result of Design Parameter for Erbium Doped Fiber Amplifier Simulation Result of Design Parameter for Erbium Doped Fiber Amplifier Calculation Result of Design Parameter for Raman Amplifier Simulation Result of Design Parameter for Raman Amplifier Simulation Result of Design Parameter for Hybrid Amplifier Simulation Result by Comparing The Gain, Noise Figure and OSNR of EDFA and Raman Amplifier by Using The same Length Gain comparison between EDFA, Raman & Hybrid amplifier Noise Figure Comparison between EDFA, Raman & Hybrid Amplifier 41

12 xii 4.9 BER Comparison between EDFA, Raman & Hybrid Amplifier Lab Test Result for WDM 48 V CONCLUSION 5.1 Discussion Conclusion 54 REFERENCES 55 APPENDICES Appendix A-H 56

13 xiii LIST OF TABLES TABLE TITLE PAGE 2.1 Transmission windows (wavelength bands) Typical value for Mux/DMux Parameter in WDM Advantages and disadvantages of Single-mode step-index, Multimode step-index, and Multimode gradient-index Characteristic of EDFA, Raman and SOA Advantages and disadvantages of EDFA, Raman and SOA Typical values observed in Hybrid amplifier (EDFA-Raman) Calculated Gain, Noise Figure and OSNR of EDFA from 8m to 12m with input signal 0dBm Simulated Gain, Noise Figure and OSNR of EDFA from 8m to 12m with input signal 0dBm Simulated Gain, Noise Figure and BER of EDFA from 8m to 12m with input signal 0dBm at different frequency spacing Calculated Gain, Noise Figure and OSNR of Raman from 20km to 25km with input signal 0dBm Simulated Gain, Noise Figure and BER of Raman from 20km to 25km with input signal 0dBm at different number of channel Simulated Gain, Noise Figure and BER of EDFA from 20km to 25km with input signal 0dBm at different frequency spacing Simulated Gain, Noise Figure and BER of Hybrid (EDFA=8m, Raman=25km) with input signal 0dBm at different number of channel 35

14 xiv 4.8 Simulated Gain, Noise Figure and BER of Hybrid (EDFA=8m, Raman=25km) with input signal 0dBm at different frequency spacing Simulation result by comparing the Gain, Noise Figure and OSNR by using the same length Gain comparison between EDFA, Raman & Hybrid amplifier with 0dBm input signal Gain comparison between EDFA, Raman & Hybrid amplifier with -10dBm input signal Gain comparison between EDFA, Raman & Hybrid amplifier with 10dBm input signal Noise Figure comparison between EDFA, Raman & Hybrid amplifier with 0dBm input signal Noise Figure comparison between EDFA, Raman & Hybrid amplifier with -10dBm input signal Noise Figure comparison between EDFA, Raman & Hybrid amplifier with -10dBm input signal BER comparison between EDFA, Raman & Hybrid amplifier with 0dBm input signal BER comparison between EDFA, Raman & Hybrid amplifier with -10dBm input signal BER comparison between EDFA, Raman & Hybrid amplifier with 10dBm input signal Received Power for an optical cable with length of 1m and 3m Output Power for different value of Output Frequency by using WDM (set 1) Output Power for different value of Output Frequency by using WDM (set 2) 49

15 xv LIST OF FIGURES FIGURE TITLE PAGE 2.1 Wavelengths-Division-Multiplexing (WDM) Core Index Profiles Eye-pattern Schematic diagram of EDFA Energy level of Er3+ ions in EDFA Schematic of an optical communication system employing Raman Amplification Semiconductor Optical Amplifier Schematic diagram of HFAs Project Flow Chart Project Block Diagram Schematic Diagram of single EDFA with 0dBm input signal Schematic diagram of single Raman amplifier with 0dBm input signal Schematic diagram of Hybrid (EDFA + Raman) amplifier with 0dBm input signal Lab Test of WDM by using 1m and 3m cable Comparison of Gain between EDFA, Raman & Hybrid amplifier at 0dBm input signal Comparison of Gain between EDFA, Raman & Hybrid amplifier at -10dBm input signal 39

16 xvi 4.3 Comparison of Gain between EDFA, Raman & Hybrid amplifier at 10dBm input signal Comparison of Noise Figure between EDFA, Raman & Hybrid amplifier at 0dBm input signal Comparison of Noise Figure between EDFA, Raman & Hybrid amplifier at -10dBm input signal Comparison of Noise Figure between EDFA, Raman & Hybrid amplifier at 10dBm input signal 45

17 xvii LIST OF APPENDIX APPENDIX TITLE PAGE A B Eye diagram for EDFA at 8m to 12m with input signal at 0dB 56 Eye diagram for Raman at 20km to 25km with input signal at 0dB 59 C Eye diagram for Hybrid Amplifier at different wavelength 63 D Calculation of EDFA for different length 67 E Calculation of Raman Amplifier for different length 71 F Calculation of Hybrid Amplifier at length of 8m (EDFA) and 25km (Raman) 77 G Datasheet for WDM 79 H Technical Specification of Optical Amplifier 81

18 xviii LIST OF ABBREVIATIONS ASE - Amplified Spontaneous Emission BER - Bit Error Rate DMux - Demultiplexer DRA - Distributed Raman Amplifier EDFA - Erbium-Doped Fiber Amplifier HFAs - Hybrid Fiber Amplifiers Mux - Multiplexer NF - Noise Figure OSA - Optical Spectrum Analyzer OSNR - Optical Signal-to-Noise Ratio P H - Power High P M - Power Medium SNR - Signal-to-Noise Ratio SOAs - Semiconductor Optical Amplifiers WDM - Wavelength-Division-Multiplexing

19 1 CHAPTER I INTRODUCTION In optical fiber network, amplifiers are used to regenerate an optical signal, amplify and then retransmitting an optical signal. In a long-haul optical systems, the amplifiers are needed to compensate the attenuation occurred. The main purpose of this project is to investigate and determine the characteristic of Erbium-Doped Fiber Amplifier (EDFA), Raman Amplifier, and Hybrid Raman and Erbium-Doped Fiber Amplifier (HFAs) and its performance in telecommunication by using the Optisystem software. After that, the best optical amplifier will be chosen among these amplifiers. Since the performance of the amplifier is influenced by the parameter of gain, Noise Figure (NF), Bit Error Rate (BER), and Optical-Signal-to-Noise Ratio (OSNR), the problem encounter in this project is to find the best design parameter for maximum reachable transmission distance. Optisystem software is used as the simulation tools for the whole project. Optisystem software is based on the realistic modeling for the fiber optic communication systems and serves a wide range of applications, thus it is an ideal simulation tools for this project. Since the simulation would not give the significant result in this project without understanding the calculation in this aspect, therefore this project also will explore the theoretical.

20 2 1.1 Objectives of Project The objectives of this project are: 1) To identify the best optical amplifier that can be used in the WDM system. 2) To suggest a new design of optical WDM transmission by using the best optical amplifier characteristic. 3) To analyze the simulated data obtained from the Optisystem software. 1.2 Scopes of Works This project will be focused primarily on the simulation of Erbium-Doped Fiber Amplifier (EDFA), Raman Amplifier, and Hybrid Raman and Erbium-Doped Fiber Amplifier (HFAs) by using the Optisystem software. The performance of the amplifiers will be evaluated depend on the amplifier s gain, Noise Figure (NF), Bit Error Rate (BER), Optical Signal-to-Noise Ratio (OSNR), and eye-pattern. After that, comparison of result between the simulation result and theoretical result will be analyzed. 1.3 Problems Statement Optical amplifiers have become a necessary component in long-haul fiber optic systems due to the demand for longer transmission lengths. The effect of dispersion and attenuation can be minimized in long-haul optical systems due to the invention of Erbium-Doped Fiber Amplifier (EDFA), Raman Amplifier, and Semiconductor Optical Amplifier (SOAs). In order to have a high capacity transmission system, there are several ways such as by using the WDM technique, increase the power of output transmission system, reduce the losses in transmission system and etc. by increase the number of optical amplifier in long-haul transmission system is able to increase the output power of transmission system but this will increase the costs. Thus, the best solution is to evaluate the best performance of optical amplifier.

21 3 1.4 Methodology This project will starts with the searching of source and information regarding to the EDFA, Raman amplifier, and HFA. The source and information are acquired from journal, reference books, e-books, and internet. The circuit schematic diagrams of these amplifiers are determined from the journal and simulate by using the Optisystem software. All the parameters such as gain, Noise Figure (NF), Bit Error Rate (BER), Optical Signal-to-Noise Ratio (OSNR), and eye-pattern that determine the performance of these amplifiers are analyzed. 1.5 Thesis Outlines Chapter 1: The first chapter will provide a general inspiration for the project. It includes the objectives of the project, scopes of works, problems statement and the methodology. Chapter 2: In this chapter, the research of background related to the project will be discussed. The concept and theory of the circuit schematic diagram of Erbium-Doped Fiber Amplifier (EDFA), Raman amplifier, and Hybrid Raman and Erbium-Doped Fiber Amplifier (HFA) that is used in the simulation will be explained. Chapter 3: The third chapter is the methodology. In this chapter, the procedure and project flow of this project will be shown. Chapter 4: This chapter will present all the simulation result from the Optisystem software. All the graphs and tables obtained from the simulation will be compared with the theoretical results. Chapter 5: The last chapter of this thesis is the conclusion and recommendation. The results will be evaluated based on the objectives of the project. It s followed by some recommendation for the future study about this project.

22 4 CHAPTER II LITERATURE REVIEW 2.1 Fiber Optic is Green Technology For instance, when a solar company improves energy conversion rate by a couple of percents, it is a market-breaking result! Slow improvements seem to be characteristic of energy production. But it is time we use technology innovation and put the best minds to work in order to improve energy efficiency across the board. It is possible. One example: first experiments in emitting diodes started in early nineties with very small efficiency. Fifteen years later, semiconductor lights are surpassing incandescent lights thanks to improvements typical of the semiconductor industry (performance doubling roughly every 2 years aka. as Moore s law). But it is fair to say that performance increase cannot always go hand-to-hand with energy efficiency. If we continue to take the semiconductor analogy, Moore s law is possible thanks to the ability to integrate more and more transistors and reduce the resolution of printed circuit boards. This comes with a cost though: power consumption. As distances get finer, power dissipation increases too. This explains why personal computers feel hotter on our laps, or why servers require fancier cooling systems. Heat dissipation is a real problem in today s processors. Actually, if we continue to increase integrated circuit speed, their power density would reach the mark of a nuclear reactor within 10 years.

23 5 In contrast, fiber optics is a very green technology compared to semiconductor electronics. It dissipates a lot less energy than copper based cables and it saves a lot of materials: one single strand of glass can carry as much data as many thousands of copper cables and it can do over a longer distance without using electronic equipment to regenerate it. The oceans for example are a lot less crowded with more efficient fiber-optic submarine cables while supporting an ever growing need for international communications. In the other hand, fiber optics does not create any environmental polluting waste or byproducts or do not emit any harmful radiations etc. 2.2 Wavelengths-Division-Multiplexing (WDM) Wavelengths-division-multiplexing (WDM) is the basic technology of optical networking. It is a technique for using a fiber (or optical device) to carry many separate and independent optical channels as shown in Figure 1. The wavelength division multiplexing (WDM) is one of the most efficient techniques for increasing the information carrying capacity of an optical fiber communication system. The number of multiplexed channels is increased by reducing the channel spacing. The reduction in channel spacing increases the crosstalk and hence the performance of the system degrades considerably. There is continuous effort in scientific community to devise methods to decrease it [1]. Figure 2.1: Wavelength-Division-Multiplexing (WDM) Wavelength selective couplers are used both to mix (multiplex) and to separate (demultiplex) the signals. The distinguishing characteristic is very wide separation of wavelength used (different band rather than different wavelengths in

24 6 the same band). Some systems are using a single fiber bidirectional for each direction. Each channel is allocated its own wavelength or rather range wavelength. A typical optical channel might be separate in 1nm wide. This channel is really a wavelength range within which the signal must stay. Normally, it s much wider the signal itself. The width of the channel depends on many things such as the modulated line width of the transmitter, its stability and the tolerances of the other components in the system. Table 2.1 shows the transmission windows for different wavelength bands. Table 2.1: Transmission windows (wavelength bands) Bands Description Wavelength Range (nm) O band Original E band Extended S band Short Wavelength C band Conventional ( erbium window ) L band Long Wavelength U band Ultra-long Wavelength In most of telecommunication system, C band is chosen because C band has the lowest attenuation losses and achieves the longest range, compatible with fiber amplifiers. There is some specification of the WDM such as conventional single-mode fibers transmit wavelengths in the 1300nm and 1550nm ranges and absorb wavelengths in the nm ranges. Therefore, WDM use wavelengths in the two regions of 1310nm and 1550nm. The other specifications for use in WDM are as shown in Table 2.2.